include/configs/woodburn_common.h - filogic/uboot - Gitiles

 /*
  * (C) Copyright 2011, Stefano Babic <sbabic@denx.de>
  *
  * (C) Copyright 2008-2010 Freescale Semiconductor, Inc.
  *
  * Configuration for the woodburn board.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __WOODBURN_COMMON_CONFIG_H
 #define __WOODBURN_COMMON_CONFIG_H

 #include <asm/arch/imx-regs.h>

  /* High Level Configuration Options */
 #define CONFIG_MX35
 #define CONFIG_MX35_HCLK_FREQ	24000000
 #define CONFIG_SYS_FSL_CLK

 #define CONFIG_SYS_DCACHE_OFF

 #define CONFIG_MACH_TYPE		MACH_TYPE_FLEA3

 /* This is required to setup the ESDC controller */

 #define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs */
 #define CONFIG_REVISION_TAG
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_INITRD_TAG

 /*
  * Size of malloc() pool
  */
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 1024 * 1024)

 /*
  * Hardware drivers
  */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_MXC
 #define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
 #define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
 #define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
 #define CONFIG_SYS_SPD_BUS_NUM		0
 #define CONFIG_MXC_SPI

 /* PMIC Controller */
 #define CONFIG_POWER
 #define CONFIG_POWER_I2C
 #define CONFIG_POWER_FSL
 #define CONFIG_POWER_FSL_MC13892
 #define CONFIG_SYS_FSL_PMIC_I2C_ADDR	0x8
 #define CONFIG_RTC_MC13XXX

 /* mmc driver */
 #define CONFIG_FSL_ESDHC
 #define CONFIG_SYS_FSL_ESDHC_ADDR	0
 #define CONFIG_SYS_FSL_ESDHC_NUM	1

 /*
  * UART (console)
  */
 #define CONFIG_MXC_UART
 #define CONFIG_MXC_UART_BASE	UART1_BASE

 /* allow to overwrite serial and ethaddr */
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_CONS_INDEX	1

 /*
  * Command definition
  */
 #define CONFIG_BOOTP_SUBNETMASK
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_DNS

 #define CONFIG_NET_RETRY_COUNT	100


 #define CONFIG_LOADADDR		0x80800000	/* loadaddr env var */

 /*
  * Ethernet on SOC (FEC)
  */
 #define CONFIG_FEC_MXC
 #define IMX_FEC_BASE	FEC_BASE_ADDR
 #define CONFIG_FEC_MXC_PHYADDR	0x1

 #define CONFIG_MII
 #define CONFIG_DISCOVER_PHY

 #define CONFIG_ARP_TIMEOUT	200UL

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP	/* undef to save memory */
 #define CONFIG_CMDLINE_EDITING

 #define CONFIG_AUTO_COMPLETE

 #define CONFIG_SYS_MEMTEST_START	0	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x10000

 #define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR

 /*
  * Physical Memory Map
  */
 #define CONFIG_NR_DRAM_BANKS	1
 #define PHYS_SDRAM_1		CSD0_BASE_ADDR
 #define PHYS_SDRAM_1_SIZE	(256 * 1024 * 1024)

 #define CONFIG_SYS_SDRAM_BASE		CSD0_BASE_ADDR

 #define CONFIG_SYS_GBL_DATA_OFFSET	(LOW_LEVEL_SRAM_STACK - \
 						IRAM_BASE_ADDR - \
 						GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_ADDR		(IRAM_BASE_ADDR + \
 					CONFIG_SYS_GBL_DATA_OFFSET)

 /*
  * MTD Command for mtdparts
  */
 #define CONFIG_MTD_DEVICE
 #define CONFIG_FLASH_CFI_MTD
 #define CONFIG_MTD_PARTITIONS

 /*
  * FLASH and environment organization
  */
 #define CONFIG_SYS_FLASH_BASE		CS0_BASE_ADDR
 #define CONFIG_SYS_MAX_FLASH_BANKS 1	/* max number of memory banks */
 #define CONFIG_SYS_MAX_FLASH_SECT 512	/* max number of sectors on one chip */
 /* Monitor at beginning of flash */
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_MONITOR_LEN		(512 * 1024)

 #define CONFIG_ENV_SECT_SIZE	(128 * 1024)
 #define CONFIG_ENV_SIZE		CONFIG_ENV_SECT_SIZE

 /* Address and size of Redundant Environment Sector	*/
 #define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
 #define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE

 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
 				CONFIG_SYS_MONITOR_LEN)

 /*
  * CFI FLASH driver setup
  */
 #define CONFIG_SYS_FLASH_CFI		/* Flash memory is CFI compliant */
 #define CONFIG_FLASH_CFI_DRIVER

 /* A non-standard buffered write algorithm */
 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	/* faster */
 #define CONFIG_SYS_FLASH_PROTECTION	/* Use hardware sector protection */

 /*
  * NAND FLASH driver setup
  */
 #define CONFIG_NAND_MXC_V1_1
 #define CONFIG_MXC_NAND_REGS_BASE	(NFC_BASE_ADDR)
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
 #define CONFIG_SYS_NAND_BASE		(NFC_BASE_ADDR)
 #define CONFIG_MXC_NAND_HWECC
 #define CONFIG_SYS_NAND_LARGEPAGE

 #define CONFIG_SYS_NAND_ONFI_DETECTION

 /*
  * Default environment and default scripts
  * to update uboot and load kernel
  */

 #define CONFIG_HOSTNAME woodburn
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
 		"nfsroot=${serverip}:${rootpath}\0"			\
 	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
 	"addip_sta=setenv bootargs ${bootargs} "			\
 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
 		":${hostname}:${netdev}:off panic=1\0"			\
 	"addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0"		\
 	"addip=if test -n ${ipdyn};then run addip_dyn;"			\
 		"else run addip_sta;fi\0"	\
 	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"		\
 	"addtty=setenv bootargs ${bootargs}"				\
 		" console=ttymxc0,${baudrate}\0"			\
 	"addmisc=setenv bootargs ${bootargs} ${misc}\0"			\
 	"loadaddr=80800000\0"						\
 	"kernel_addr_r=80800000\0"					\
 	"hostname=" __stringify(CONFIG_HOSTNAME) "\0"			\
 	"bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0"		\
 	"ramdisk_file=" __stringify(CONFIG_HOSTNAME) "/uRamdisk\0"	\
 	"flash_self=run ramargs addip addtty addmtd addmisc;"		\
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"flash_nfs=run nfsargs addip addtty addmtd addmisc;"		\
 		"bootm ${kernel_addr}\0"				\
 	"net_nfs=tftp ${kernel_addr_r} ${bootfile}; "			\
 		"run nfsargs addip addtty addmtd addmisc;"		\
 		"bootm ${kernel_addr_r}\0"				\
 	"net_self_load=tftp ${kernel_addr_r} ${bootfile};"		\
 		"tftp ${ramdisk_addr_r} ${ramdisk_file};\0"		\
 	"net_self=if run net_self_load;then "				\
 		"run ramargs addip addtty addmtd addmisc;"		\
 		"bootm ${kernel_addr_r} ${ramdisk_addr_r};"		\
 		"else echo Images not loades;fi\0"			\
 	"u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.bin\0"		\
 	"load=tftp ${loadaddr} ${u-boot}\0"				\
 	"uboot_addr=" __stringify(CONFIG_SYS_MONITOR_BASE) "\0"		\
 	"update=protect off ${uboot_addr} +80000;"			\
 		"erase ${uboot_addr} +80000;"				\
 		"cp.b ${loadaddr} ${uboot_addr} ${filesize}\0"		\
 	"upd=if run load;then echo Updating u-boot;if run update;"	\
 		"then echo U-Boot updated;"				\
 			"else echo Error updating u-boot !;"		\
 			"echo Board without bootloader !!;"		\
 		"fi;"							\
 		"else echo U-Boot not downloaded..exiting;fi\0"		\
 	"bootcmd=run net_nfs\0"

 #endif				/* __CONFIG_H */
	/*
	* (C) Copyright 2011, Stefano Babic <sbabic@denx.de>
	*
	* (C) Copyright 2008-2010 Freescale Semiconductor, Inc.
	*
	* Configuration for the woodburn board.
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __WOODBURN_COMMON_CONFIG_H
	#define __WOODBURN_COMMON_CONFIG_H

	#include <asm/arch/imx-regs.h>

	/* High Level Configuration Options */
	#define CONFIG_MX35
	#define CONFIG_MX35_HCLK_FREQ 24000000
	#define CONFIG_SYS_FSL_CLK

	#define CONFIG_SYS_DCACHE_OFF

	#define CONFIG_MACH_TYPE MACH_TYPE_FLEA3

	/* This is required to setup the ESDC controller */

	#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
	#define CONFIG_REVISION_TAG
	#define CONFIG_SETUP_MEMORY_TAGS
	#define CONFIG_INITRD_TAG

	/*
	* Size of malloc() pool
	*/
	#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1024 * 1024)

	/*
	* Hardware drivers
	*/
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_MXC
	#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
	#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
	#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
	#define CONFIG_SYS_SPD_BUS_NUM 0
	#define CONFIG_MXC_SPI

	/* PMIC Controller */
	#define CONFIG_POWER
	#define CONFIG_POWER_I2C
	#define CONFIG_POWER_FSL
	#define CONFIG_POWER_FSL_MC13892
	#define CONFIG_SYS_FSL_PMIC_I2C_ADDR 0x8
	#define CONFIG_RTC_MC13XXX

	/* mmc driver */
	#define CONFIG_FSL_ESDHC
	#define CONFIG_SYS_FSL_ESDHC_ADDR 0
	#define CONFIG_SYS_FSL_ESDHC_NUM 1

	/*
	* UART (console)
	*/
	#define CONFIG_MXC_UART
	#define CONFIG_MXC_UART_BASE UART1_BASE

	/* allow to overwrite serial and ethaddr */
	#define CONFIG_ENV_OVERWRITE
	#define CONFIG_CONS_INDEX 1

	/*
	* Command definition
	*/
	#define CONFIG_BOOTP_SUBNETMASK
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_DNS

	#define CONFIG_NET_RETRY_COUNT 100


	#define CONFIG_LOADADDR 0x80800000 /* loadaddr env var */

	/*
	* Ethernet on SOC (FEC)
	*/
	#define CONFIG_FEC_MXC
	#define IMX_FEC_BASE FEC_BASE_ADDR
	#define CONFIG_FEC_MXC_PHYADDR 0x1

	#define CONFIG_MII
	#define CONFIG_DISCOVER_PHY

	#define CONFIG_ARP_TIMEOUT 200UL

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_CMDLINE_EDITING

	#define CONFIG_AUTO_COMPLETE

	#define CONFIG_SYS_MEMTEST_START 0 /* memtest works on */
	#define CONFIG_SYS_MEMTEST_END 0x10000

	#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR

	/*
	* Physical Memory Map
	*/
	#define CONFIG_NR_DRAM_BANKS 1
	#define PHYS_SDRAM_1 CSD0_BASE_ADDR
	#define PHYS_SDRAM_1_SIZE (256 * 1024 * 1024)

	#define CONFIG_SYS_SDRAM_BASE CSD0_BASE_ADDR

	#define CONFIG_SYS_GBL_DATA_OFFSET (LOW_LEVEL_SRAM_STACK - \
	IRAM_BASE_ADDR - \
	GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_ADDR (IRAM_BASE_ADDR + \
	CONFIG_SYS_GBL_DATA_OFFSET)

	/*
	* MTD Command for mtdparts
	*/
	#define CONFIG_MTD_DEVICE
	#define CONFIG_FLASH_CFI_MTD
	#define CONFIG_MTD_PARTITIONS

	/*
	* FLASH and environment organization
	*/
	#define CONFIG_SYS_FLASH_BASE CS0_BASE_ADDR
	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
	/* Monitor at beginning of flash */
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_MONITOR_LEN (512 * 1024)

	#define CONFIG_ENV_SECT_SIZE (128 * 1024)
	#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE

	/* Address and size of Redundant Environment Sector */
	#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
	#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE

	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
	CONFIG_SYS_MONITOR_LEN)

	/*
	* CFI FLASH driver setup
	*/
	#define CONFIG_SYS_FLASH_CFI /* Flash memory is CFI compliant */
	#define CONFIG_FLASH_CFI_DRIVER

	/* A non-standard buffered write algorithm */
	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* faster */
	#define CONFIG_SYS_FLASH_PROTECTION /* Use hardware sector protection */

	/*
	* NAND FLASH driver setup
	*/
	#define CONFIG_NAND_MXC_V1_1
	#define CONFIG_MXC_NAND_REGS_BASE (NFC_BASE_ADDR)
	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	#define CONFIG_SYS_NAND_BASE (NFC_BASE_ADDR)
	#define CONFIG_MXC_NAND_HWECC
	#define CONFIG_SYS_NAND_LARGEPAGE

	#define CONFIG_SYS_NAND_ONFI_DETECTION

	/*
	* Default environment and default scripts
	* to update uboot and load kernel
	*/

	#define CONFIG_HOSTNAME woodburn
	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0" \
	"nfsargs=setenv bootargs root=/dev/nfs rw " \
	"nfsroot=${serverip}:${rootpath}\0" \
	"ramargs=setenv bootargs root=/dev/ram rw\0" \
	"addip_sta=setenv bootargs ${bootargs} " \
	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	":${hostname}:${netdev}:off panic=1\0" \
	"addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0" \
	"addip=if test -n ${ipdyn};then run addip_dyn;" \
	"else run addip_sta;fi\0" \
	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
	"addtty=setenv bootargs ${bootargs}" \
	" console=ttymxc0,${baudrate}\0" \
	"addmisc=setenv bootargs ${bootargs} ${misc}\0" \
	"loadaddr=80800000\0" \
	"kernel_addr_r=80800000\0" \
	"hostname=" __stringify(CONFIG_HOSTNAME) "\0" \
	"bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0" \
	"ramdisk_file=" __stringify(CONFIG_HOSTNAME) "/uRamdisk\0" \
	"flash_self=run ramargs addip addtty addmtd addmisc;" \
	"bootm ${kernel_addr} ${ramdisk_addr}\0" \
	"flash_nfs=run nfsargs addip addtty addmtd addmisc;" \
	"bootm ${kernel_addr}\0" \
	"net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
	"run nfsargs addip addtty addmtd addmisc;" \
	"bootm ${kernel_addr_r}\0" \
	"net_self_load=tftp ${kernel_addr_r} ${bootfile};" \
	"tftp ${ramdisk_addr_r} ${ramdisk_file};\0" \
	"net_self=if run net_self_load;then " \
	"run ramargs addip addtty addmtd addmisc;" \
	"bootm ${kernel_addr_r} ${ramdisk_addr_r};" \
	"else echo Images not loades;fi\0" \
	"u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.bin\0" \
	"load=tftp ${loadaddr} ${u-boot}\0" \
	"uboot_addr=" __stringify(CONFIG_SYS_MONITOR_BASE) "\0" \
	"update=protect off ${uboot_addr} +80000;" \
	"erase ${uboot_addr} +80000;" \
	"cp.b ${loadaddr} ${uboot_addr} ${filesize}\0" \
	"upd=if run load;then echo Updating u-boot;if run update;" \
	"then echo U-Boot updated;" \
	"else echo Error updating u-boot !;" \
	"echo Board without bootloader !!;" \
	"fi;" \
	"else echo U-Boot not downloaded..exiting;fi\0" \
	"bootcmd=run net_nfs\0"

	#endif /* __CONFIG_H */