| /* |
| * Copyright (c) 2016 - 2020, Broadcom |
| * |
| * SPDX-License-Identifier: BSD-3-Clause |
| */ |
| |
| #ifndef CSL_SD_PROT_H |
| #define CSL_SD_PROT_H |
| |
| #define SD_CARD_UNKNOWN 0 /* bad type or unrecognized */ |
| #define SD_CARD_SD 1 /* IO only card */ |
| #define SD_CARD_SDIO 2 /* memory only card */ |
| #define SD_CARD_COMBO 3 /* IO and memory combo card */ |
| #define SD_CARD_MMC 4 /* memory only card */ |
| #define SD_CARD_CEATA 5 /* IO and memory combo card */ |
| |
| #define SD_IO_FIXED_ADDRESS 0 /* fix Address */ |
| #define SD_IO_INCREMENT_ADDRESS 1 |
| |
| #define SD_HIGH_CAPACITY_CARD 0x40000000 |
| |
| #define MMC_CMD_IDLE_RESET_ARG 0xF0F0F0F0 |
| |
| /* Supported operating voltages are 3.2-3.3 and 3.3-3.4 */ |
| #define MMC_OCR_OP_VOLT 0x00300000 |
| /* Enable sector access mode */ |
| #define MMC_OCR_SECTOR_ACCESS_MODE 0x40000000 |
| |
| /* command index */ |
| #define SD_CMD_GO_IDLE_STATE 0 /* mandatory for SDIO */ |
| #define SD_CMD_SEND_OPCOND 1 |
| #define SD_CMD_ALL_SEND_CID 2 |
| #define SD_CMD_MMC_SET_RCA 3 |
| #define SD_CMD_MMC_SET_DSR 4 |
| #define SD_CMD_IO_SEND_OP_COND 5 /* mandatory for SDIO */ |
| #define SD_ACMD_SET_BUS_WIDTH 6 |
| #define SD_CMD_SWITCH_FUNC 6 |
| #define SD_CMD_SELECT_DESELECT_CARD 7 |
| #define SD_CMD_READ_EXT_CSD 8 |
| #define SD_CMD_SEND_CSD 9 |
| #define SD_CMD_SEND_CID 10 |
| #define SD_CMD_STOP_TRANSMISSION 12 |
| #define SD_CMD_SEND_STATUS 13 |
| #define SD_ACMD_SD_STATUS 13 |
| #define SD_CMD_GO_INACTIVE_STATE 15 |
| #define SD_CMD_SET_BLOCKLEN 16 |
| #define SD_CMD_READ_SINGLE_BLOCK 17 |
| #define SD_CMD_READ_MULTIPLE_BLOCK 18 |
| #define SD_CMD_WRITE_BLOCK 24 |
| #define SD_CMD_WRITE_MULTIPLE_BLOCK 25 |
| #define SD_CMD_PROGRAM_CSD 27 |
| #define SD_CMD_SET_WRITE_PROT 28 |
| #define SD_CMD_CLR_WRITE_PROT 29 |
| #define SD_CMD_SEND_WRITE_PROT 30 |
| #define SD_CMD_ERASE_WR_BLK_START 32 |
| #define SD_CMD_ERASE_WR_BLK_END 33 |
| #define SD_CMD_ERASE_GROUP_START 35 |
| #define SD_CMD_ERASE_GROUP_END 36 |
| #define SD_CMD_ERASE 38 |
| #define SD_CMD_LOCK_UNLOCK 42 |
| #define SD_CMD_IO_RW_DIRECT 52 /* mandatory for SDIO */ |
| #define SD_CMD_IO_RW_EXTENDED 53 /* mandatory for SDIO */ |
| #define SD_CMD_APP_CMD 55 |
| #define SD_CMD_GEN_CMD 56 |
| #define SD_CMD_READ_OCR 58 |
| #define SD_CMD_CRC_ON_OFF 59 /* mandatory for SDIO */ |
| #define SD_ACMD_SEND_NUM_WR_BLOCKS 22 |
| #define SD_ACMD_SET_WR_BLOCK_ERASE_CNT 23 |
| #define SD_ACMD_SD_SEND_OP_COND 41 |
| #define SD_ACMD_SET_CLR_CARD_DETECT 42 |
| #define SD_ACMD_SEND_SCR 51 |
| |
| /* response parameters */ |
| #define SD_RSP_NO_NONE 0 |
| #define SD_RSP_NO_1 1 |
| #define SD_RSP_NO_2 2 |
| #define SD_RSP_NO_3 3 |
| #define SD_RSP_NO_4 4 |
| #define SD_RSP_NO_5 5 |
| #define SD_RSP_NO_6 6 |
| |
| /* Modified R6 response (to CMD3) */ |
| #define SD_RSP_MR6_COM_CRC_ERROR 0x8000 |
| #define SD_RSP_MR6_ILLEGAL_COMMAND 0x4000 |
| #define SD_RSP_MR6_ERROR 0x2000 |
| |
| /* Modified R1 in R4 Response (to CMD5) */ |
| #define SD_RSP_MR1_SBIT 0x80 |
| #define SD_RSP_MR1_PARAMETER_ERROR 0x40 |
| #define SD_RSP_MR1_RFU5 0x20 |
| #define SD_RSP_MR1_FUNC_NUM_ERROR 0x10 |
| #define SD_RSP_MR1_COM_CRC_ERROR 0x80 |
| #define SD_RSP_MR1_ILLEGAL_COMMAND 0x40 |
| #define SD_RSP_MR1_RFU1 0x20 |
| #define SD_RSP_MR1_IDLE_STATE 0x01 |
| |
| /* R5 response (to CMD52 and CMD53) */ |
| #define SD_RSP_R5_COM_CRC_ERROR 0x80 |
| #define SD_RSP_R5_ILLEGAL_COMMAND 0x40 |
| #define SD_RSP_R5_IO_CURRENTSTATE1 0x20 |
| #define SD_RSP_R5_IO_CURRENTSTATE0 0x10 |
| #define SD_RSP_R5_ERROR 0x80 |
| #define SD_RSP_R5_RFU 0x40 |
| #define SD_RSP_R5_FUNC_NUM_ERROR 0x20 |
| #define SD_RSP_R5_OUT_OF_RANGE 0x01 |
| |
| /* argument for SD_CMD_IO_RW_DIRECT and SD_CMD_IO_RW_EXTENDED */ |
| #define SD_OP_READ 0 /* Read_Write */ |
| #define SD_OP_WRITE 1 /* Read_Write */ |
| |
| #define SD_RW_NORMAL 0 /* no RAW */ |
| #define SD_RW_RAW 1 /* RAW */ |
| |
| #define SD_BYTE_MODE 0 /* Byte Mode */ |
| #define SD_BLOCK_MODE 1 /* BlockMode */ |
| |
| #define SD_FIXED_ADDRESS 0 /* fix Address */ |
| #define SD_INCREMENT_ADDRESS 1 /* IncrementAddress */ |
| |
| #define SD_CMD5_ARG_IO_OCR_MASK 0x00FFFFFF |
| #define SD_CMD5_ARG_IO_OCR_SHIFT 0 |
| #define SD_CMD55_ARG_RCA_SHIFT 16 |
| #define SD_CMD59_ARG_CRC_OPTION_MASK 0x01 |
| #define SD_CMD59_ARG_CRC_OPTION_SHIFT 0 |
| |
| /* SD_CMD_IO_RW_DIRECT Argument */ |
| #define SdioIoRWDirectArg(rw, raw, func, addr, data) \ |
| (((rw & 1) << 31) | ((func & 0x7) << 28) | \ |
| ((raw & 1) << 27) | ((addr & 0x1FFFF) << 9) | \ |
| (data & 0xFF)) |
| |
| /* build SD_CMD_IO_RW_EXTENDED Argument */ |
| #define SdioIoRWExtArg(rw, blk, func, addr, inc_addr, count) \ |
| (((rw & 1) << 31) | ((func & 0x7) << 28) | \ |
| ((blk & 1) << 27) | ((inc_addr & 1) << 26) | \ |
| ((addr & 0x1FFFF) << 9) | (count & 0x1FF)) |
| |
| /* |
| * The Common I/O area shall be implemented on all SDIO cards and |
| * is accessed the the host via I/O reads and writes to function 0, |
| * the registers within the CIA are provided to enable/disable |
| * the operationo fthe i/o function. |
| */ |
| |
| /* cccr_sdio_rev */ |
| #define SDIO_REV_SDIOID_MASK 0xf0 /* SDIO spec revision number */ |
| #define SDIO_REV_CCCRID_MASK 0x0f /* CCCR format version number */ |
| |
| /* sd_rev */ |
| #define SDIO_REV_PHY_MASK 0x0f /* SD format version number */ |
| #define SDIO_FUNC_ENABLE_1 0x02 /* function 1 I/O enable */ |
| #define SDIO_FUNC_READY_1 0x02 /* function 1 I/O ready */ |
| #define SDIO_INTR_CTL_FUNC1_EN 0x2 /* interrupt enable for function 1 */ |
| #define SDIO_INTR_CTL_MASTER_EN 0x1 /* interrupt enable master */ |
| #define SDIO_INTR_STATUS_FUNC1 0x2 /* interrupt pending for function 1 */ |
| #define SDIO_IO_ABORT_RESET_ALL 0x08 /* I/O card reset */ |
| #define SDIO_IO_ABORT_FUNC_MASK 0x07 /* abort selection: function x */ |
| #define SDIO_BUS_CARD_DETECT_DIS 0x80 /* Card Detect disable */ |
| #define SDIO_BUS_SPI_CONT_INTR_CAP 0x40 /* support continuous SPI interrupt */ |
| #define SDIO_BUS_SPI_CONT_INTR_EN 0x20 /* continuous SPI interrupt enable */ |
| #define SDIO_BUS_DATA_WIDTH_MASK 0x03 /* bus width mask */ |
| #define SDIO_BUS_DATA_WIDTH_4BIT 0x02 /* bus width 4-bit mode */ |
| #define SDIO_BUS_DATA_WIDTH_1BIT 0x00 /* bus width 1-bit mode */ |
| |
| /* capability */ |
| #define SDIO_CAP_4BLS 0x80 /* 4-bit support for low speed card */ |
| #define SDIO_CAP_LSC 0x40 /* low speed card */ |
| #define SDIO_CAP_E4MI 0x20 /* enable int between block in 4-bit mode */ |
| #define SDIO_CAP_S4MI 0x10 /* support int between block in 4-bit mode */ |
| #define SDIO_CAP_SBS 0x08 /* support suspend/resume */ |
| #define SDIO_CAP_SRW 0x04 /* support read wait */ |
| #define SDIO_CAP_SMB 0x02 /* support multi-block transfer */ |
| #define SDIO_CAP_SDC 0x01 /* Support Direct cmd during multi-uint8 transfer */ |
| |
| /* CIA FBR1 registers */ |
| #define SDIO_FUNC1_INFO 0x100 /* basic info for function 1 */ |
| #define SDIO_FUNC1_EXT 0x101 /* extension of standard I/O device */ |
| #define SDIO_CIS_FUNC1_BASE_LOW 0x109 /* function 1 cis address bit 0-7 */ |
| #define SDIO_CIS_FUNC1_BASE_MID 0x10A /* function 1 cis address bit 8-15 */ |
| #define SDIO_CIS_FUNC1_BASE_HIGH 0x10B /* function 1 cis address bit 16 */ |
| #define SDIO_CSA_BASE_LOW 0x10C /* CSA base address uint8_t 0 */ |
| #define SDIO_CSA_BASE_MID 0x10D /* CSA base address uint8_t 1 */ |
| #define SDIO_CSA_BASE_HIGH 0x10E /* CSA base address uint8_t 2 */ |
| #define SDIO_CSA_DATA_OFFSET 0x10F /* CSA data register */ |
| #define SDIO_IO_BLK_SIZE_LOW 0x110 /* I/O block size uint8_t 0 */ |
| #define SDIO_IO_BLK_SIZE_HIGH 0x111 /* I/O block size uint8_t 1 */ |
| |
| /* SD_SDIO_FUNC1_INFO bits */ |
| #define SDIO_FUNC1_INFO_DIC 0x0f /* device interface code */ |
| #define SDIO_FUNC1_INFO_CSA 0x40 /* CSA support flag */ |
| #define SDIO_FUNC1_INFO_CSA_EN 0x80 /* CSA enabled */ |
| |
| /* SD_SDIO_FUNC1_EXT bits */ |
| #define SDIO_FUNC1_EXT_SHP 0x03 /* support high power */ |
| #define SDIO_FUNC1_EXT_EHP 0x04 /* enable high power */ |
| |
| /* devctr */ |
| /* I/O device interface code */ |
| #define SDIO_DEVCTR_DEVINTER 0x0f |
| /* support CSA */ |
| #define SDIO_DEVCTR_CSA_SUP 0x40 |
| /* enable CSA */ |
| #define SDIO_DEVCTR_CSA_EN 0x80 |
| |
| /* ext_dev */ |
| /* supports high-power mask */ |
| #define SDIO_HIGHPWR_SUPPORT_M 0x3 |
| /* enable high power */ |
| #define SDIO_HIGHPWR_EN 0x4 |
| /* standard power function(up to 200mA */ |
| #define SDIO_HP_STD 0 |
| /* need high power to operate */ |
| #define SDIO_HP_REQUIRED 0x2 |
| /* can work with standard power, but prefer high power */ |
| #define SDIO_HP_DESIRED 0x3 |
| |
| /* misc define */ |
| /* macro to calculate fbr register base */ |
| #define FBR_REG_BASE(n) (n*0x100) |
| #define SDIO_FUNC_0 0 |
| #define SDIO_FUNC_1 1 |
| #define SDIO_FUNC_2 2 |
| #define SDIO_FUNC_3 3 |
| #define SDIO_FUNC_4 4 |
| #define SDIO_FUNC_5 5 |
| #define SDIO_FUNC_6 6 |
| #define SDIO_FUNC_7 7 |
| |
| /* maximum block size for block mode operation */ |
| #define SDIO_MAX_BLOCK_SIZE 2048 |
| /* minimum block size for block mode operation */ |
| #define SDIO_MIN_BLOCK_SIZE 1 |
| |
| /* Card registers: status bit position */ |
| #define SDIO_STATUS_OUTOFRANGE 31 |
| #define SDIO_STATUS_COMCRCERROR 23 |
| #define SDIO_STATUS_ILLEGALCOMMAND 22 |
| #define SDIO_STATUS_ERROR 19 |
| #define SDIO_STATUS_IOCURRENTSTATE3 12 |
| #define SDIO_STATUS_IOCURRENTSTATE2 11 |
| #define SDIO_STATUS_IOCURRENTSTATE1 10 |
| #define SDIO_STATUS_IOCURRENTSTATE0 9 |
| #define SDIO_STATUS_FUN_NUM_ERROR 4 |
| |
| #define GET_SDIOCARD_STATUS(x) ((x >> 9) & 0x0f) |
| #define SDIO_STATUS_STATE_IDLE 0 |
| #define SDIO_STATUS_STATE_READY 1 |
| #define SDIO_STATUS_STATE_IDENT 2 |
| #define SDIO_STATUS_STATE_STBY 3 |
| #define SDIO_STATUS_STATE_TRAN 4 |
| #define SDIO_STATUS_STATE_DATA 5 |
| #define SDIO_STATUS_STATE_RCV 6 |
| #define SDIO_STATUS_STATE_PRG 7 |
| #define SDIO_STATUS_STATE_DIS 8 |
| |
| /* sprom */ |
| #define SBSDIO_SPROM_CS 0x10000 /* command and status */ |
| #define SBSDIO_SPROM_INFO 0x10001 /* info register */ |
| #define SBSDIO_SPROM_DATA_LOW 0x10002 /* indirect access data uint8_t 0 */ |
| #define SBSDIO_SPROM_DATA_HIGH 0x10003 /* indirect access data uint8_t 1 */ |
| #define SBSDIO_SPROM_ADDR_LOW 0x10004 /* indirect access addr uint8_t 0 */ |
| #define SBSDIO_SPROM_ADDR_HIGH 0x10005 /* indirect access addr uint8_t 0 */ |
| #define SBSDIO_CHIP_CTRL_DATA 0x10006 /* xtal_pu data output */ |
| #define SBSDIO_CHIP_CTRL_EN 0x10007 /* xtal_pu enable */ |
| #define SBSDIO_WATERMARK 0x10008 /* retired in rev 7 */ |
| #define SBSDIO_DEVICE_CTL 0x10009 /* control busy signal generation */ |
| |
| #define SBSDIO_SPROM_IDLE 0 |
| #define SBSDIO_SPROM_WRITE 1 |
| #define SBSDIO_SPROM_READ 2 |
| #define SBSDIO_SPROM_WEN 4 |
| #define SBSDIO_SPROM_WDS 7 |
| #define SBSDIO_SPROM_DONE 8 |
| |
| /* SBSDIO_SPROM_INFO */ |
| #define SBSDIO_SROM_SZ_MASK 0x03 /* SROM size, 1: 4k, 2: 16k */ |
| #define SBSDIO_SROM_BLANK 0x04 /* depreciated in corerev 6 */ |
| #define SBSDIO_SROM_OTP 0x80 /* OTP present */ |
| |
| /* SBSDIO_CHIP_CTRL */ |
| /* or'd with onchip xtal_pu, 1: power on oscillator */ |
| #define SBSDIO_CHIP_CTRL_XTAL 0x01 |
| |
| /* SBSDIO_WATERMARK */ |
| /* number of bytes minus 1 for sd device to wait before sending data to host */ |
| #define SBSDIO_WATERMARK_MASK 0x3f |
| |
| /* SBSDIO_DEVICE_CTL */ |
| /* 1: device will assert busy signal when receiving CMD53 */ |
| #define SBSDIO_DEVCTL_SETBUSY 0x01 |
| /* 1: assertion of sdio interrupt is synchronous to the sdio clock */ |
| #define SBSDIO_DEVCTL_SPI_INTR_SYNC 0x02 |
| |
| /* function 1 OCP space */ |
| /* sb offset addr is <= 15 bits, 32k */ |
| #define SBSDIO_SB_OFT_ADDR_MASK 0x07FFF |
| #define SBSDIO_SB_OFT_ADDR_LIMIT 0x08000 |
| /* sdsdio function 1 OCP space has 16/32 bit section */ |
| #define SBSDIO_SB_ACCESS_2_4B_FLAG 0x08000 |
| |
| /* direct(mapped) cis space */ |
| /* MAPPED common CIS address */ |
| #define SBSDIO_CIS_BASE_COMMON 0x1000 |
| /* function 0(common) cis size in bytes */ |
| #define SBSDIO_CIS_FUNC0_LIMIT 0x020 |
| /* function 1 cis size in bytes */ |
| #define SBSDIO_CIS_SIZE_LIMIT 0x200 |
| /* cis offset addr is < 17 bits */ |
| #define SBSDIO_CIS_OFT_ADDR_MASK 0x1FFFF |
| /* manfid tuple length, include tuple, link bytes */ |
| #define SBSDIO_CIS_MANFID_TUPLE_LEN 6 |
| |
| /* indirect cis access (in sprom) */ |
| /* 8 control bytes first, CIS starts from 8th uint8_t */ |
| #define SBSDIO_SPROM_CIS_OFFSET 0x8 |
| /* sdio uint8_t mode: maximum length of one data command */ |
| #define SBSDIO_BYTEMODE_DATALEN_MAX 64 |
| /* 4317 supports less */ |
| #define SBSDIO_BYTEMODE_DATALEN_MAX_4317 52 |
| /* sdio core function one address mask */ |
| #define SBSDIO_CORE_ADDR_MASK 0x1FFFF |
| |
| /* CEATA defines */ |
| #define CEATA_EXT_CSDBLOCK_SIZE 512 |
| #define CEATA_FAST_IO 39 |
| #define CEATA_MULTIPLE_REGISTER_RW 60 |
| #define CEATA_MULTIPLE_BLOCK_RW 61 |
| |
| /* defines CE ATA task file registers */ |
| #define CEATA_SCT_CNT_EXP_REG 0x02 |
| #define CEATA_LBA_LOW_EXP_REG 0x03 |
| #define CEATA_LBA_MID_EXP_REG 0x04 |
| #define CEATA_LBA_HIGH_EXP_REG 0x05 |
| #define CEATA_CNTRL_REG 0x06 |
| #define CEATA_FEATURE_REG 0x09 /* write */ |
| #define CEATA_ERROR_REG 0x09 /* read */ |
| #define CEATA_SCT_CNT_REG 0x0A |
| #define CEATA_LBA_LOW_REG 0x0B |
| #define CEATA_LBA_MID_REG 0x0C |
| #define CEATA_LBA_HIGH_REG 0x0D |
| #define CEATA_DEV_HEAD_REG 0x0E |
| #define CEATA_STA_REG 0x0F /* read */ |
| #define CEATA_CMD_REG 0x0F /* write */ |
| |
| /* defines CEATA control and status registers for ce ata client driver */ |
| #define CEATA_SCR_TEMPC_REG 0x80 |
| #define CEATA_SCR_TEMPMAXP_REG 0x84 |
| #define CEATA_TEMPMINP_REG 0x88 |
| #define CEATA_SCR_STATUS_REG 0x8C |
| #define CEATA_SCR_REALLOCSA_REG 0x90 |
| #define CEATA_SCR_ERETRACTSA_REG 0x94 |
| #define CEATA_SCR_CAPABILITIES_REG 0x98 |
| #define CEATA_SCR_CONTROL_REG 0xC0 |
| |
| /* defines for SCR capabilities register bits for ce ata client driver */ |
| #define CEATA_SCR_CAP_512 0x00000001 |
| #define CEATA_SCR_CAP_1K 0x00000002 |
| #define CEATA_SCR_CAP_4K 0x00000004 |
| |
| /* defines CE ATA Control reg bits for ce ata client driver */ |
| #define CEATA_CNTRL_ENABLE_INTR 0x00 |
| #define CEATA_CNTRL_DISABLE_INTR 0x02 |
| #define CEATA_CNTRL_SRST 0x04 |
| #define CEATA_CNTRL_RSRST 0x00 |
| |
| /* define CE ATA Status reg bits for ce ata client driver */ |
| #define CEATA_STA_ERROR_BIT 0x01 |
| #define CEATA_STA_OVR_BIT 0x02 |
| #define CEATA_STA_SPT_BIT 0x04 |
| #define CEATA_STA_DRQ_BIT 0x08 |
| #define CEATA_STA_DRDY_BIT 0x40 |
| #define CEATA_STA_BSY_BIT 0x80 |
| |
| /* define CE ATA Error reg bits for ce ata client driver */ |
| #define CEATA_ERROR_ABORTED_BIT 0x04 |
| #define CEATA_ERROR_IDNF_BIT 0x10 |
| #define CEATA_ERROR_UNCORRECTABLE_BIT 0x40 |
| #define CEATA_ERROR_ICRC_BIT 0x80 |
| |
| /* define CE ATA Commands for ce ata client driver */ |
| #define CEATA_CMD_IDENTIFY_DEVICE 0xEC |
| #define CEATA_CMD_READ_DMA_EXT 0x25 |
| #define CEATA_CMD_WRITE_DMA_EXT 0x35 |
| #define CEATA_CMD_STANDBY_IMMEDIATE 0xE0 |
| #define CEATA_CMD_FLUSH_CACHE_EXT 0xEA |
| |
| struct csd_mmc { |
| uint32_t padding:8; |
| uint32_t structure:2; |
| uint32_t csdSpecVer:4; |
| uint32_t reserved1:2; |
| uint32_t taac:8; |
| uint32_t nsac:8; |
| uint32_t speed:8; |
| uint32_t classes:12; |
| uint32_t rdBlkLen:4; |
| uint32_t rdBlkPartial:1; |
| uint32_t wrBlkMisalign:1; |
| uint32_t rdBlkMisalign:1; |
| uint32_t dsr:1; |
| uint32_t reserved2:2; |
| uint32_t size:12; |
| uint32_t vddRdCurrMin:3; |
| uint32_t vddRdCurrMax:3; |
| uint32_t vddWrCurrMin:3; |
| uint32_t vddWrCurrMax:3; |
| uint32_t devSizeMulti:3; |
| uint32_t eraseGrpSize:5; |
| uint32_t eraseGrpSizeMulti:5; |
| uint32_t wrProtGroupSize:5; |
| uint32_t wrProtGroupEnable:1; |
| uint32_t manuDefEcc:2; |
| uint32_t wrSpeedFactor:3; |
| uint32_t wrBlkLen:4; |
| uint32_t wrBlkPartial:1; |
| uint32_t reserved5:4; |
| uint32_t protAppl:1; |
| uint32_t fileFormatGrp:1; |
| uint32_t copyFlag:1; |
| uint32_t permWrProt:1; |
| uint32_t tmpWrProt:1; |
| uint32_t fileFormat:2; |
| uint32_t eccCode:2; |
| }; |
| |
| /* CSD register*/ |
| union sd_csd { |
| uint32_t csd[4]; |
| struct csd_mmc mmc; |
| }; |
| |
| struct sd_card_data { |
| union sd_csd csd; |
| }; |
| #endif /* CSL_SD_PROT_H */ |