| /* |
| * Copyright (c) 2013-2017, ARM Limited and Contributors. All rights reserved. |
| * |
| * SPDX-License-Identifier: BSD-3-Clause |
| */ |
| |
| #include <arch.h> |
| #include <asm_macros.S> |
| #include <cpu_macros.S> |
| #include <platform_def.h> |
| |
| .weak plat_secondary_cold_boot_setup |
| .weak plat_get_my_entrypoint |
| .globl css_calc_core_pos_swap_cluster |
| .weak plat_is_my_cpu_primary |
| |
| /* --------------------------------------------------------------------- |
| * void plat_secondary_cold_boot_setup(void); |
| * |
| * In the normal boot flow, cold-booting secondary CPUs is not yet |
| * implemented and they panic. |
| * |
| * When booting an EL3 payload, secondary CPUs are placed in a holding |
| * pen, waiting for their mailbox to be populated. Note that all CPUs |
| * share the same mailbox ; therefore, populating it will release all |
| * CPUs from their holding pen. If finer-grained control is needed then |
| * this should be handled in the code that secondary CPUs jump to. |
| * --------------------------------------------------------------------- |
| */ |
| func plat_secondary_cold_boot_setup |
| #ifndef EL3_PAYLOAD_BASE |
| /* TODO: Implement secondary CPU cold boot setup on CSS platforms */ |
| cb_panic: |
| b cb_panic |
| #else |
| mov_imm x0, PLAT_ARM_TRUSTED_MAILBOX_BASE |
| |
| /* Wait until the mailbox gets populated */ |
| poll_mailbox: |
| ldr x1, [x0] |
| cbz x1, 1f |
| br x1 |
| 1: |
| wfe |
| b poll_mailbox |
| #endif /* EL3_PAYLOAD_BASE */ |
| endfunc plat_secondary_cold_boot_setup |
| |
| /* --------------------------------------------------------------------- |
| * uintptr_t plat_get_my_entrypoint (void); |
| * |
| * Main job of this routine is to distinguish between a cold and a warm |
| * boot. On CSS platforms, this distinction is based on the contents of |
| * the Trusted Mailbox. It is initialised to zero by the SCP before the |
| * AP cores are released from reset. Therefore, a zero mailbox means |
| * it's a cold reset. |
| * |
| * This functions returns the contents of the mailbox, i.e.: |
| * - 0 for a cold boot; |
| * - the warm boot entrypoint for a warm boot. |
| * --------------------------------------------------------------------- |
| */ |
| func plat_get_my_entrypoint |
| mov_imm x0, PLAT_ARM_TRUSTED_MAILBOX_BASE |
| ldr x0, [x0] |
| ret |
| endfunc plat_get_my_entrypoint |
| |
| /* ----------------------------------------------------------- |
| * unsigned int css_calc_core_pos_swap_cluster(u_register_t mpidr) |
| * Utility function to calculate the core position by |
| * swapping the cluster order. This is necessary in order to |
| * match the format of the boot information passed by the SCP |
| * and read in plat_is_my_cpu_primary below. |
| * ----------------------------------------------------------- |
| */ |
| func css_calc_core_pos_swap_cluster |
| and x1, x0, #MPIDR_CPU_MASK |
| and x0, x0, #MPIDR_CLUSTER_MASK |
| eor x0, x0, #(1 << MPIDR_AFFINITY_BITS) // swap cluster order |
| add x0, x1, x0, LSR #6 |
| ret |
| endfunc css_calc_core_pos_swap_cluster |
| |
| /* ----------------------------------------------------- |
| * unsigned int plat_is_my_cpu_primary (void); |
| * |
| * Find out whether the current cpu is the primary |
| * cpu (applicable ony after a cold boot) |
| * ----------------------------------------------------- |
| */ |
| #if CSS_USE_SCMI_SDS_DRIVER |
| func plat_is_my_cpu_primary |
| mov x9, x30 |
| bl plat_my_core_pos |
| mov x4, x0 |
| bl sds_get_primary_cpu_id |
| /* Check for error */ |
| mov x1, #0xffffffff |
| cmp x0, x1 |
| b.eq 1f |
| cmp x0, x4 |
| cset w0, eq |
| ret x9 |
| 1: |
| no_ret plat_panic_handler |
| endfunc plat_is_my_cpu_primary |
| #else |
| func plat_is_my_cpu_primary |
| mov x9, x30 |
| bl plat_my_core_pos |
| mov_imm x1, SCP_BOOT_CFG_ADDR |
| ldr x1, [x1] |
| ubfx x1, x1, #PLAT_CSS_PRIMARY_CPU_SHIFT, \ |
| #PLAT_CSS_PRIMARY_CPU_BIT_WIDTH |
| cmp x0, x1 |
| cset w0, eq |
| ret x9 |
| endfunc plat_is_my_cpu_primary |
| #endif |