blob: 8130d7d7b6f219a7c3d877a0b5e6ab50d1ebce64 [file] [log] [blame]
Measured Boot Design
====================
This document briefly explains the Measured-Boot design implementation
in |TF-A|.
Introduction
------------
Measured Boot is the process of computing and securely recording hashes of code
and critical data at each stage in the boot chain before the code/data is used.
These measurements can be leveraged by other components in the system to
implement a complete attestation system. For example, they could be used to
enforce local attestation policies (such as releasing certain platform keys or
not), or they could be securely sent to a remote challenger a.k.a. `verifier`
after boot to attest to the state of the code and critical-data.
Measured Boot does not authenticate the code or critical-data, but simply
records what code/critical-data was present on the system during boot.
It is assumed that BL1 is implicitly trusted (by virtue of immutability) and
acts as the root of trust for measurement hence it is not measured.
The Measured Boot implementation in TF-A supports multiple backends to securely
store measurements mentioned below in the :ref:`Measured Boot Backends` section.
Critical data
-------------
All firmware images - i.e. BLx images and their corresponding configuration
files, if any - must be measured. In addition to that, there might be specific
pieces of data which needs to be measured as well. These are typically different
on each platform. They are referred to as *critical data*.
Critical data for the platform can be determined using the following criteria:
#. Data that influence boot flow behaviour such as -
- Configuration parameters that alter the boot flow path.
- Parameters that determine which firmware to load from NV-Storage to
SRAM/DRAM to pass the boot process successfully.
#. Hardware configurations settings, debug settings and security policies
that need to be in a valid state for a device to maintain its security
posture during boot and runtime.
#. Security-sensitive data that is being updated by hardware.
Examples of Critical data:
#. The list of errata workarounds being applied at reset.
#. State of fuses such as whether an SoC is in secure mode.
#. NV counters that determine whether firmware is up-to-date and secure.
Measurement slot
----------------
The measurement slot resides in a Trusted Module and can be either a secure
register or memory.
The measurement slot is used to provide a method to cryptographically record
(measure) images and critical data on a platform.
The measurement slot update calculation, called an **extend** operation, is
a one-way hash of all the previous measurements and the new measurement. It
is the only way to change the slot value, thus no measurements can ever be
removed or overwritten.
.. _Measured Boot Backends:
Measured Boot Backends
----------------------
The Measured Boot implementation in TF-A supports:
#. Event Log
The TCG Event Log holds a record of measurements made into the Measurement
Slot aka PCR (Platform Configuration Register).
The `TCG EFI Protocol Specification`_ provides details on how to measure
components. The Arm document
`Arm® Server Base Security Guide`_ provides specific guidance for
measurements on an SBSA/SBBR server system. By considering these
specifications it is decided that -
#. Use PCR0 for images measurements.
#. Use PCR1 for Critical data measurements.
TCG has specified the architecture for the structure of this log in the
`TCG EFI Protocol Specification`_. The specification describes two event
log event recordsthe legacy, fixed size SHA1 structure called TCG_PCR_EVENT
and the variable length crypto agile structure called TCG_PCR_EVENT2. Event
Log driver implemented in TF-A covers later part.
#. RSS
It is one of physical backend to extend the measurements. Please refer this
document :ref:`Runtime Security Subsystem (RSS)` for more details.
Platform Interface
------------------
Every image which gets successfully loaded in memory (and authenticated, if
trusted boot is enabled) then gets measured. In addition to that, platforms
can measure any relevant piece of critical data at any point during the boot.
The following diagram outlines the call sequence for Measured Boot platform
interfaces invoked from generic code:
.. image:: ../resources/diagrams/measured_boot_design.png
These platform interfaces are used by BL1 and BL2 only, and are declared in
``include/plat/common/platform.h``.
BL31 does not load and thus does not measure any image.
Responsibilities of these platform interfaces are -
#. **Function : blx_plat_mboot_init()**
.. code-block:: c
void bl1_plat_mboot_init(void);
void bl2_plat_mboot_init(void);
Initialise all Measured Boot backends supported by the platform
(e.g. Event Log buffer, RSS). As these functions do not return any value,
the platform should deal with error management, such as logging the error
somewhere, or panicking the system if this is considered a fatal error.
- On the Arm FVP port -
- In BL1, this function is used to initialize the Event Log backend
driver, and also to write header information in the Event Log
buffer.
- In BL2, this function is used to initialize the Event Log buffer with
the information received from the BL1. It results in panic on
error.
#. **Function : plat_mboot_measure_image()**
.. code-block:: c
int plat_mboot_measure_image(unsigned int image_id,
image_info_t *image_data);
- Measure the image using a hash function of the crypto module.
- Record the measurement in the corresponding backend -
- If it is Event Log backend, then record the measurement in TCG Event Log
format.
- If it is a secure crypto-processor (like RSS), then extend the designated
PCR (or slot) with the given measurement.
- This function must return 0 on success, a signed integer error code
otherwise.
- On the Arm FVP port, this function measures the given image and then
records that measurement in the Event Log buffer.
The passed id is used to retrieve information about on how to measure
the image (e.g. PCR number).
#. **Function : blx_plat_mboot_finish()**
.. code-block:: c
void bl1_plat_mboot_finish(void);
void bl2_plat_mboot_finish(void);
- Do all teardown operations with respect to initialised Measured Boot backends.
This could be -
- Pass the Event Log details (start address and size) to Normal world or to
Secure World using any platform implementation way.
- Measure all critical data if any.
- As these functions do not return any value, the platform should deal with
error management, such as logging the error somewhere, or panicking the
system if this is considered a fatal error.
- On the Arm FVP port -
- In BL1, this function is used to pass the base address of
the Event Log buffer and its size to BL2 via tb_fw_config to extend the
Event Log buffer with the measurement of various images loaded by BL2.
It results in panic on error.
- In BL2, this function is used to pass the Event Log buffer information
(base address and size) to non-secure(BL33) and trusted OS(BL32) via
nt_fw and tos_fw config respectively.
See :ref:`DTB binding for Event Log properties` for a description of the
bindings used for Event Log properties.
#. **Function : plat_mboot_measure_critical_data()**
.. code-block:: c
int plat_mboot_measure_critical_data(unsigned int critical_data_id,
const void *base,
size_t size);
This interface is not invoked by the generic code and it is up to the
platform layer to call it where appropriate.
This function measures the given critical data structure and records its
measurement using the Measured Boot backend driver.
This function must return 0 on success, a signed integer error code
otherwise.
In FVP, Non volatile counters get measured and recorded as Critical data
using the backend via this interface.
--------------
*Copyright (c) 2023, Arm Limited. All rights reserved.*
.. _Arm® Server Base Security Guide: https://developer.arm.com/documentation/den0086/latest
.. _TCG EFI Protocol Specification: https://trustedcomputinggroup.org/wp-content/uploads/EFI-Protocol-Specification-rev13-160330final.pdf