blob: a83a0ad16082dd151b20e2a479e2980a33b15736 [file] [log] [blame]
/*
* Copyright (c) 2016-2018, ARM Limited and Contributors. All rights reserved.
*
* SPDX-License-Identifier: BSD-3-Clause
*/
#ifndef __RPI3_HW__
#define __RPI3_HW__
#include <utils_def.h>
/*
* Peripherals
*/
#define RPI3_IO_BASE ULL(0x3F000000)
#define RPI3_IO_SIZE ULL(0x01000000)
/*
* ARM <-> VideoCore mailboxes
*/
#define RPI3_MBOX_OFFSET ULL(0x0000B880)
#define RPI3_MBOX_BASE (RPI3_IO_BASE + RPI3_MBOX_OFFSET)
/* VideoCore -> ARM */
#define RPI3_MBOX0_READ_OFFSET ULL(0x00000000)
#define RPI3_MBOX0_PEEK_OFFSET ULL(0x00000010)
#define RPI3_MBOX0_SENDER_OFFSET ULL(0x00000014)
#define RPI3_MBOX0_STATUS_OFFSET ULL(0x00000018)
#define RPI3_MBOX0_CONFIG_OFFSET ULL(0x0000001C)
/* ARM -> VideoCore */
#define RPI3_MBOX1_WRITE_OFFSET ULL(0x00000020)
#define RPI3_MBOX1_PEEK_OFFSET ULL(0x00000030)
#define RPI3_MBOX1_SENDER_OFFSET ULL(0x00000034)
#define RPI3_MBOX1_STATUS_OFFSET ULL(0x00000038)
#define RPI3_MBOX1_CONFIG_OFFSET ULL(0x0000003C)
/* Mailbox status constants */
#define RPI3_MBOX_STATUS_FULL_MASK U(0x80000000) /* Set if full */
#define RPI3_MBOX_STATUS_EMPTY_MASK U(0x40000000) /* Set if empty */
/*
* Power management, reset controller, watchdog.
*/
#define RPI3_IO_PM_OFFSET ULL(0x00100000)
#define RPI3_PM_BASE (RPI3_IO_BASE + RPI3_IO_PM_OFFSET)
/* Registers on top of RPI3_PM_BASE. */
#define RPI3_PM_RSTC_OFFSET ULL(0x0000001C)
#define RPI3_PM_RSTS_OFFSET ULL(0x00000020)
#define RPI3_PM_WDOG_OFFSET ULL(0x00000024)
/* Watchdog constants */
#define RPI3_PM_PASSWORD U(0x5A000000)
#define RPI3_PM_RSTC_WRCFG_MASK U(0x00000030)
#define RPI3_PM_RSTC_WRCFG_FULL_RESET U(0x00000020)
/*
* The RSTS register is used by the VideoCore firmware when booting the
* Raspberry Pi to know which partition to boot from. The partition value is
* formed by bits 0, 2, 4, 6, 8 and 10. Partition 63 is used by said firmware
* to indicate halt.
*/
#define RPI3_PM_RSTS_WRCFG_HALT U(0x00000555)
/*
* Serial port (called 'Mini UART' in the BCM docucmentation).
*/
#define RPI3_IO_MINI_UART_OFFSET ULL(0x00215040)
#define RPI3_MINI_UART_BASE (RPI3_IO_BASE + RPI3_IO_MINI_UART_OFFSET)
#define RPI3_MINI_UART_CLK_IN_HZ ULL(500000000)
/*
* Local interrupt controller
*/
#define RPI3_INTC_BASE_ADDRESS ULL(0x40000000)
/* Registers on top of RPI3_INTC_BASE_ADDRESS */
#define RPI3_INTC_CONTROL_OFFSET ULL(0x00000000)
#define RPI3_INTC_PRESCALER_OFFSET ULL(0x00000008)
#define RPI3_INTC_MBOX_CONTROL_OFFSET ULL(0x00000050)
#define RPI3_INTC_MBOX_CONTROL_SLOT3_FIQ ULL(0x00000080)
#define RPI3_INTC_PENDING_FIQ_OFFSET ULL(0x00000070)
#define RPI3_INTC_PENDING_FIQ_MBOX3 ULL(0x00000080)
#endif /* __RPI3_HW__ */