plat/allwinner/sun50i_a64/sunxi_power.c - filogic/atf - Gitiles

 /*
  * Copyright (c) 2017-2018, ARM Limited and Contributors. All rights reserved.
  * Copyright (c) 2018, Icenowy Zheng <icenowy@aosc.io>
  *
  * SPDX-License-Identifier: BSD-3-Clause
  */

 #include <allwinner/sunxi_rsb.h>
 #include <arch_helpers.h>
 #include <debug.h>
 #include <delay_timer.h>
 #include <errno.h>
 #include <libfdt.h>
 #include <mmio.h>
 #include <platform_def.h>
 #include <sunxi_def.h>
 #include <sunxi_mmap.h>
 #include <sunxi_private.h>

 static enum pmic_type {
 	GENERIC_H5,
 	GENERIC_A64,
 	REF_DESIGN_H5,	/* regulators controlled by GPIO pins on port L */
 	AXP803_RSB,	/* PMIC connected via RSB on most A64 boards */
 } pmic;

 #define AXP803_HW_ADDR	0x3a3
 #define AXP803_RT_ADDR	0x2d

 /*
  * On boards without a proper PMIC we struggle to turn off the system properly.
  * Try to turn off as much off the system as we can, to reduce power
  * consumption. This should be entered with only one core running and SMP
  * disabled.
  * This function only cares about peripherals.
  */
 void sunxi_turn_off_soc(uint16_t socid)
 {
 	int i;

 	/** Turn off most peripherals, most importantly DRAM users. **/
 	/* Keep DRAM controller running for now. */
 	mmio_clrbits_32(SUNXI_CCU_BASE + 0x2c0, ~BIT_32(14));
 	mmio_clrbits_32(SUNXI_CCU_BASE + 0x60, ~BIT_32(14));
 	/* Contains msgbox (bit 21) and spinlock (bit 22) */
 	mmio_write_32(SUNXI_CCU_BASE + 0x2c4, 0);
 	mmio_write_32(SUNXI_CCU_BASE + 0x64, 0);
 	mmio_write_32(SUNXI_CCU_BASE + 0x2c8, 0);
 	/* Keep PIO controller running for now. */
 	mmio_clrbits_32(SUNXI_CCU_BASE + 0x68, ~(BIT_32(5)));
 	mmio_write_32(SUNXI_CCU_BASE + 0x2d0, 0);
 	/* Contains UART0 (bit 16) */
 	mmio_write_32(SUNXI_CCU_BASE + 0x2d8, 0);
 	mmio_write_32(SUNXI_CCU_BASE + 0x6c, 0);
 	mmio_write_32(SUNXI_CCU_BASE + 0x70, 0);

 	/** Turn off DRAM controller. **/
 	mmio_clrbits_32(SUNXI_CCU_BASE + 0x2c0, BIT_32(14));
 	mmio_clrbits_32(SUNXI_CCU_BASE + 0x60, BIT_32(14));

 	/** Migrate CPU and bus clocks away from the PLLs. **/
 	/* AHB1: use OSC24M/1, APB1 = AHB1 / 2 */
 	mmio_write_32(SUNXI_CCU_BASE + 0x54, 0x1000);
 	/* APB2: use OSC24M */
 	mmio_write_32(SUNXI_CCU_BASE + 0x58, 0x1000000);
 	/* AHB2: use AHB1 clock */
 	mmio_write_32(SUNXI_CCU_BASE + 0x5c, 0);
 	/* CPU: use OSC24M */
 	mmio_write_32(SUNXI_CCU_BASE + 0x50, 0x10000);

 	/** Turn off PLLs. **/
 	for (i = 0; i < 6; i++)
 		mmio_clrbits_32(SUNXI_CCU_BASE + i * 8, BIT(31));
 	switch (socid) {
 	case SUNXI_SOC_H5:
 		mmio_clrbits_32(SUNXI_CCU_BASE + 0x44, BIT(31));
 		break;
 	case SUNXI_SOC_A64:
 		mmio_clrbits_32(SUNXI_CCU_BASE + 0x2c, BIT(31));
 		mmio_clrbits_32(SUNXI_CCU_BASE + 0x4c, BIT(31));
 		break;
 	}
 }

 static int rsb_init(void)
 {
 	int ret;

 	ret = rsb_init_controller();
 	if (ret)
 		return ret;

 	/* Start with 400 KHz to issue the I2C->RSB switch command. */
 	ret = rsb_set_bus_speed(SUNXI_OSC24M_CLK_IN_HZ, 400000);
 	if (ret)
 		return ret;

 	/*
 	 * Initiate an I2C transaction to write 0x7c into register 0x3e,
 	 * switching the PMIC to RSB mode.
 	 */
 	ret = rsb_set_device_mode(0x7c3e00);
 	if (ret)
 		return ret;

 	/* Now in RSB mode, switch to the recommended 3 MHz. */
 	ret = rsb_set_bus_speed(SUNXI_OSC24M_CLK_IN_HZ, 3000000);
 	if (ret)
 		return ret;

 	/* Associate the 8-bit runtime address with the 12-bit bus address. */
 	return rsb_assign_runtime_address(AXP803_HW_ADDR,
 					  AXP803_RT_ADDR);
 }

 static int axp_write(uint8_t reg, uint8_t val)
 {
 	return rsb_write(AXP803_RT_ADDR, reg, val);
 }

 static int axp_setbits(uint8_t reg, uint8_t set_mask)
 {
 	uint8_t regval;
 	int ret;

 	ret = rsb_read(AXP803_RT_ADDR, reg);
 	if (ret < 0)
 		return ret;

 	regval = ret | set_mask;

 	return rsb_write(AXP803_RT_ADDR, reg, regval);
 }

 static bool should_enable_regulator(const void *fdt, int node)
 {
 	if (fdt_getprop(fdt, node, "phandle", NULL) != NULL)
 		return true;
 	if (fdt_getprop(fdt, node, "regulator-always-on", NULL) != NULL)
 		return true;
 	return false;
 }

 /*
  * Retrieve the voltage from a given regulator DTB node.
  * Both the regulator-{min,max}-microvolt properties must be present and
  * have the same value. Return that value in millivolts.
  */
 static int fdt_get_regulator_millivolt(const void *fdt, int node)
 {
 	const fdt32_t *prop;
 	uint32_t min_volt;

 	prop = fdt_getprop(fdt, node, "regulator-min-microvolt", NULL);
 	if (prop == NULL)
 		return -EINVAL;
 	min_volt = fdt32_to_cpu(*prop);

 	prop = fdt_getprop(fdt, node, "regulator-max-microvolt", NULL);
 	if (prop == NULL)
 		return -EINVAL;

 	if (fdt32_to_cpu(*prop) != min_volt)
 		return -EINVAL;

 	return min_volt / 1000;
 }

 #define NO_SPLIT 0xff

 struct axp_regulator {
 	char *dt_name;
 	uint16_t min_volt;
 	uint16_t max_volt;
 	uint16_t step;
 	unsigned char split;
 	unsigned char volt_reg;
 	unsigned char switch_reg;
 	unsigned char switch_bit;
 } regulators[] = {
 	{"dcdc1", 1600, 3400, 100, NO_SPLIT, 0x20, 0xff, 9},
 	{"dcdc5",  800, 1840,  10,       32, 0x24, 0xff, 9},
 	{"dldo1",  700, 3300, 100, NO_SPLIT, 0x15, 0x12, 3},
 	{"dldo2",  700, 4200, 100,       27, 0x16, 0x12, 4},
 	{"dldo3",  700, 3300, 100, NO_SPLIT, 0x17, 0x12, 5},
 	{"fldo1",  700, 1450,  50, NO_SPLIT, 0x1c, 0x13, 2},
 	{}
 };

 static int setup_regulator(const void *fdt, int node,
 			   const struct axp_regulator *reg)
 {
 	int mvolt;
 	uint8_t regval;

 	if (!should_enable_regulator(fdt, node))
 		return -ENOENT;

 	mvolt = fdt_get_regulator_millivolt(fdt, node);
 	if (mvolt < reg->min_volt || mvolt > reg->max_volt)
 		return -EINVAL;

 	regval = (mvolt / reg->step) - (reg->min_volt / reg->step);
 	if (regval > reg->split)
 		regval = ((regval - reg->split) / 2) + reg->split;

 	axp_write(reg->volt_reg, regval);
 	if (reg->switch_reg < 0xff)
 		axp_setbits(reg->switch_reg, BIT(reg->switch_bit));

 	INFO("PMIC: AXP803: %s voltage: %d.%03dV\n", reg->dt_name,
 	     mvolt / 1000, mvolt % 1000);

 	return 0;
 }

 static void setup_axp803_rails(const void *fdt)
 {
 	int node;
 	bool dc1sw = false;

 	/* locate the PMIC DT node, bail out if not found */
 	node = fdt_node_offset_by_compatible(fdt, -1, "x-powers,axp803");
 	if (node == -FDT_ERR_NOTFOUND) {
 		WARN("BL31: PMIC: No AXP803 DT node, skipping initial setup.\n");
 		return;
 	}

 	if (fdt_getprop(fdt, node, "x-powers,drive-vbus-en", NULL))
 		axp_setbits(0x8f, BIT(4));

 	/* descend into the "regulators" subnode */
 	node = fdt_first_subnode(fdt, node);

 	/* iterate over all regulators to find used ones */
 	for (node = fdt_first_subnode(fdt, node);
 	     node != -FDT_ERR_NOTFOUND;
 	     node = fdt_next_subnode(fdt, node)) {
 		struct axp_regulator *reg;
 		const char *name;
 		int length;

 		/* We only care if it's always on or referenced. */
 		if (!should_enable_regulator(fdt, node))
 			continue;

 		name = fdt_get_name(fdt, node, &length);
 		for (reg = regulators; reg->dt_name; reg++) {
 			if (!strncmp(name, reg->dt_name, length)) {
 				setup_regulator(fdt, node, reg);
 				break;
 			}
 		}

 		if (!strncmp(name, "dc1sw", length)) {
 			/* Delay DC1SW enablement to avoid overheating. */
 			dc1sw = true;
 			continue;
 		}
 	}
 	/*
 	 * If DLDO2 is enabled after DC1SW, the PMIC overheats and shuts
 	 * down. So always enable DC1SW as the very last regulator.
 	 */
 	if (dc1sw) {
 		INFO("PMIC: AXP803: Enabling DC1SW\n");
 		axp_setbits(0x12, BIT(7));
 	}
 }

 int sunxi_pmic_setup(uint16_t socid, const void *fdt)
 {
 	int ret;

 	switch (socid) {
 	case SUNXI_SOC_H5:
 		pmic = REF_DESIGN_H5;
 		NOTICE("BL31: PMIC: Defaulting to PortL GPIO according to H5 reference design.\n");
 		break;
 	case SUNXI_SOC_A64:
 		pmic = GENERIC_A64;
 		ret = sunxi_init_platform_r_twi(socid, true);
 		if (ret)
 			return ret;

 		ret = rsb_init();
 		if (ret)
 			return ret;

 		pmic = AXP803_RSB;
 		NOTICE("BL31: PMIC: Detected AXP803 on RSB.\n");

 		if (fdt)
 			setup_axp803_rails(fdt);

 		break;
 	default:
 		NOTICE("BL31: PMIC: No support for Allwinner %x SoC.\n", socid);
 		return -ENODEV;
 	}
 	return 0;
 }

 void __dead2 sunxi_power_down(void)
 {
 	switch (pmic) {
 	case GENERIC_H5:
 		/* Turn off as many peripherals and clocks as we can. */
 		sunxi_turn_off_soc(SUNXI_SOC_H5);
 		/* Turn off the pin controller now. */
 		mmio_write_32(SUNXI_CCU_BASE + 0x68, 0);
 		break;
 	case GENERIC_A64:
 		/* Turn off as many peripherals and clocks as we can. */
 		sunxi_turn_off_soc(SUNXI_SOC_A64);
 		/* Turn off the pin controller now. */
 		mmio_write_32(SUNXI_CCU_BASE + 0x68, 0);
 		break;
 	case REF_DESIGN_H5:
 		sunxi_turn_off_soc(SUNXI_SOC_H5);

 		/*
 		 * Switch PL pins to power off the board:
 		 * - PL5 (VCC_IO) -> high
 		 * - PL8 (PWR-STB = CPU power supply) -> low
 		 * - PL9 (PWR-DRAM) ->low
 		 * - PL10 (power LED) -> low
 		 * Note: Clearing PL8 will reset the board, so keep it up.
 		 */
 		sunxi_set_gpio_out('L', 5, 1);
 		sunxi_set_gpio_out('L', 9, 0);
 		sunxi_set_gpio_out('L', 10, 0);

 		/* Turn off pin controller now. */
 		mmio_write_32(SUNXI_CCU_BASE + 0x68, 0);

 		break;
 	case AXP803_RSB:
 		/* (Re-)init RSB in case the rich OS has disabled it. */
 		sunxi_init_platform_r_twi(SUNXI_SOC_A64, true);
 		rsb_init();

 		/* Set "power disable control" bit */
 		axp_setbits(0x32, BIT(7));
 		break;
 	default:
 		break;
 	}

 	udelay(1000);
 	ERROR("PSCI: Cannot turn off system, halting.\n");
 	wfi();
 	panic();
 }
	/*
	* Copyright (c) 2017-2018, ARM Limited and Contributors. All rights reserved.
	* Copyright (c) 2018, Icenowy Zheng <icenowy@aosc.io>
	*
	* SPDX-License-Identifier: BSD-3-Clause
	*/

	#include <allwinner/sunxi_rsb.h>
	#include <arch_helpers.h>
	#include <debug.h>
	#include <delay_timer.h>
	#include <errno.h>
	#include <libfdt.h>
	#include <mmio.h>
	#include <platform_def.h>
	#include <sunxi_def.h>
	#include <sunxi_mmap.h>
	#include <sunxi_private.h>

	static enum pmic_type {
	GENERIC_H5,
	GENERIC_A64,
	REF_DESIGN_H5, /* regulators controlled by GPIO pins on port L */
	AXP803_RSB, /* PMIC connected via RSB on most A64 boards */
	} pmic;

	#define AXP803_HW_ADDR 0x3a3
	#define AXP803_RT_ADDR 0x2d

	/*
	* On boards without a proper PMIC we struggle to turn off the system properly.
	* Try to turn off as much off the system as we can, to reduce power
	* consumption. This should be entered with only one core running and SMP
	* disabled.
	* This function only cares about peripherals.
	*/
	void sunxi_turn_off_soc(uint16_t socid)
	{
	int i;

	/ Turn off most peripherals, most importantly DRAM users. /
	/* Keep DRAM controller running for now. */
	mmio_clrbits_32(SUNXI_CCU_BASE + 0x2c0, ~BIT_32(14));
	mmio_clrbits_32(SUNXI_CCU_BASE + 0x60, ~BIT_32(14));
	/* Contains msgbox (bit 21) and spinlock (bit 22) */
	mmio_write_32(SUNXI_CCU_BASE + 0x2c4, 0);
	mmio_write_32(SUNXI_CCU_BASE + 0x64, 0);
	mmio_write_32(SUNXI_CCU_BASE + 0x2c8, 0);
	/* Keep PIO controller running for now. */
	mmio_clrbits_32(SUNXI_CCU_BASE + 0x68, ~(BIT_32(5)));
	mmio_write_32(SUNXI_CCU_BASE + 0x2d0, 0);
	/* Contains UART0 (bit 16) */
	mmio_write_32(SUNXI_CCU_BASE + 0x2d8, 0);
	mmio_write_32(SUNXI_CCU_BASE + 0x6c, 0);
	mmio_write_32(SUNXI_CCU_BASE + 0x70, 0);

	/ Turn off DRAM controller. /
	mmio_clrbits_32(SUNXI_CCU_BASE + 0x2c0, BIT_32(14));
	mmio_clrbits_32(SUNXI_CCU_BASE + 0x60, BIT_32(14));

	/ Migrate CPU and bus clocks away from the PLLs. /
	/* AHB1: use OSC24M/1, APB1 = AHB1 / 2 */
	mmio_write_32(SUNXI_CCU_BASE + 0x54, 0x1000);
	/* APB2: use OSC24M */
	mmio_write_32(SUNXI_CCU_BASE + 0x58, 0x1000000);
	/* AHB2: use AHB1 clock */
	mmio_write_32(SUNXI_CCU_BASE + 0x5c, 0);
	/* CPU: use OSC24M */
	mmio_write_32(SUNXI_CCU_BASE + 0x50, 0x10000);

	/ Turn off PLLs. /
	for (i = 0; i < 6; i++)
	mmio_clrbits_32(SUNXI_CCU_BASE + i * 8, BIT(31));
	switch (socid) {
	case SUNXI_SOC_H5:
	mmio_clrbits_32(SUNXI_CCU_BASE + 0x44, BIT(31));
	break;
	case SUNXI_SOC_A64:
	mmio_clrbits_32(SUNXI_CCU_BASE + 0x2c, BIT(31));
	mmio_clrbits_32(SUNXI_CCU_BASE + 0x4c, BIT(31));
	break;
	}
	}

	static int rsb_init(void)
	{
	int ret;

	ret = rsb_init_controller();
	if (ret)
	return ret;

	/* Start with 400 KHz to issue the I2C->RSB switch command. */
	ret = rsb_set_bus_speed(SUNXI_OSC24M_CLK_IN_HZ, 400000);
	if (ret)
	return ret;

	/*
	* Initiate an I2C transaction to write 0x7c into register 0x3e,
	* switching the PMIC to RSB mode.
	*/
	ret = rsb_set_device_mode(0x7c3e00);
	if (ret)
	return ret;

	/* Now in RSB mode, switch to the recommended 3 MHz. */
	ret = rsb_set_bus_speed(SUNXI_OSC24M_CLK_IN_HZ, 3000000);
	if (ret)
	return ret;

	/* Associate the 8-bit runtime address with the 12-bit bus address. */
	return rsb_assign_runtime_address(AXP803_HW_ADDR,
	AXP803_RT_ADDR);
	}

	static int axp_write(uint8_t reg, uint8_t val)
	{
	return rsb_write(AXP803_RT_ADDR, reg, val);
	}

	static int axp_setbits(uint8_t reg, uint8_t set_mask)
	{
	uint8_t regval;
	int ret;

	ret = rsb_read(AXP803_RT_ADDR, reg);
	if (ret < 0)
	return ret;

	regval = ret \| set_mask;

	return rsb_write(AXP803_RT_ADDR, reg, regval);
	}

	static bool should_enable_regulator(const void *fdt, int node)
	{
	if (fdt_getprop(fdt, node, "phandle", NULL) != NULL)
	return true;
	if (fdt_getprop(fdt, node, "regulator-always-on", NULL) != NULL)
	return true;
	return false;
	}

	/*
	* Retrieve the voltage from a given regulator DTB node.
	* Both the regulator-{min,max}-microvolt properties must be present and
	* have the same value. Return that value in millivolts.
	*/
	static int fdt_get_regulator_millivolt(const void *fdt, int node)
	{
	const fdt32_t *prop;
	uint32_t min_volt;

	prop = fdt_getprop(fdt, node, "regulator-min-microvolt", NULL);
	if (prop == NULL)
	return -EINVAL;
	min_volt = fdt32_to_cpu(*prop);

	prop = fdt_getprop(fdt, node, "regulator-max-microvolt", NULL);
	if (prop == NULL)
	return -EINVAL;

	if (fdt32_to_cpu(*prop) != min_volt)
	return -EINVAL;

	return min_volt / 1000;
	}

	#define NO_SPLIT 0xff

	struct axp_regulator {
	char *dt_name;
	uint16_t min_volt;
	uint16_t max_volt;
	uint16_t step;
	unsigned char split;
	unsigned char volt_reg;
	unsigned char switch_reg;
	unsigned char switch_bit;
	} regulators[] = {
	{"dcdc1", 1600, 3400, 100, NO_SPLIT, 0x20, 0xff, 9},
	{"dcdc5", 800, 1840, 10, 32, 0x24, 0xff, 9},
	{"dldo1", 700, 3300, 100, NO_SPLIT, 0x15, 0x12, 3},
	{"dldo2", 700, 4200, 100, 27, 0x16, 0x12, 4},
	{"dldo3", 700, 3300, 100, NO_SPLIT, 0x17, 0x12, 5},
	{"fldo1", 700, 1450, 50, NO_SPLIT, 0x1c, 0x13, 2},
	{}
	};

	static int setup_regulator(const void *fdt, int node,
	const struct axp_regulator *reg)
	{
	int mvolt;
	uint8_t regval;

	if (!should_enable_regulator(fdt, node))
	return -ENOENT;

	mvolt = fdt_get_regulator_millivolt(fdt, node);
	if (mvolt < reg->min_volt \|\| mvolt > reg->max_volt)
	return -EINVAL;

	regval = (mvolt / reg->step) - (reg->min_volt / reg->step);
	if (regval > reg->split)
	regval = ((regval - reg->split) / 2) + reg->split;

	axp_write(reg->volt_reg, regval);
	if (reg->switch_reg < 0xff)
	axp_setbits(reg->switch_reg, BIT(reg->switch_bit));

	INFO("PMIC: AXP803: %s voltage: %d.%03dV\n", reg->dt_name,
	mvolt / 1000, mvolt % 1000);

	return 0;
	}

	static void setup_axp803_rails(const void *fdt)
	{
	int node;
	bool dc1sw = false;

	/* locate the PMIC DT node, bail out if not found */
	node = fdt_node_offset_by_compatible(fdt, -1, "x-powers,axp803");
	if (node == -FDT_ERR_NOTFOUND) {
	WARN("BL31: PMIC: No AXP803 DT node, skipping initial setup.\n");
	return;
	}

	if (fdt_getprop(fdt, node, "x-powers,drive-vbus-en", NULL))
	axp_setbits(0x8f, BIT(4));

	/* descend into the "regulators" subnode */
	node = fdt_first_subnode(fdt, node);

	/* iterate over all regulators to find used ones */
	for (node = fdt_first_subnode(fdt, node);
	node != -FDT_ERR_NOTFOUND;
	node = fdt_next_subnode(fdt, node)) {
	struct axp_regulator *reg;
	const char *name;
	int length;

	/* We only care if it's always on or referenced. */
	if (!should_enable_regulator(fdt, node))
	continue;

	name = fdt_get_name(fdt, node, &length);
	for (reg = regulators; reg->dt_name; reg++) {
	if (!strncmp(name, reg->dt_name, length)) {
	setup_regulator(fdt, node, reg);
	break;
	}
	}

	if (!strncmp(name, "dc1sw", length)) {
	/* Delay DC1SW enablement to avoid overheating. */
	dc1sw = true;
	continue;
	}
	}
	/*
	* If DLDO2 is enabled after DC1SW, the PMIC overheats and shuts
	* down. So always enable DC1SW as the very last regulator.
	*/
	if (dc1sw) {
	INFO("PMIC: AXP803: Enabling DC1SW\n");
	axp_setbits(0x12, BIT(7));
	}
	}

	int sunxi_pmic_setup(uint16_t socid, const void *fdt)
	{
	int ret;

	switch (socid) {
	case SUNXI_SOC_H5:
	pmic = REF_DESIGN_H5;
	NOTICE("BL31: PMIC: Defaulting to PortL GPIO according to H5 reference design.\n");
	break;
	case SUNXI_SOC_A64:
	pmic = GENERIC_A64;
	ret = sunxi_init_platform_r_twi(socid, true);
	if (ret)
	return ret;

	ret = rsb_init();
	if (ret)
	return ret;

	pmic = AXP803_RSB;
	NOTICE("BL31: PMIC: Detected AXP803 on RSB.\n");

	if (fdt)
	setup_axp803_rails(fdt);

	break;
	default:
	NOTICE("BL31: PMIC: No support for Allwinner %x SoC.\n", socid);
	return -ENODEV;
	}
	return 0;
	}

	void __dead2 sunxi_power_down(void)
	{
	switch (pmic) {
	case GENERIC_H5:
	/* Turn off as many peripherals and clocks as we can. */
	sunxi_turn_off_soc(SUNXI_SOC_H5);
	/* Turn off the pin controller now. */
	mmio_write_32(SUNXI_CCU_BASE + 0x68, 0);
	break;
	case GENERIC_A64:
	/* Turn off as many peripherals and clocks as we can. */
	sunxi_turn_off_soc(SUNXI_SOC_A64);
	/* Turn off the pin controller now. */
	mmio_write_32(SUNXI_CCU_BASE + 0x68, 0);
	break;
	case REF_DESIGN_H5:
	sunxi_turn_off_soc(SUNXI_SOC_H5);

	/*
	* Switch PL pins to power off the board:
	* - PL5 (VCC_IO) -> high
	* - PL8 (PWR-STB = CPU power supply) -> low
	* - PL9 (PWR-DRAM) ->low
	* - PL10 (power LED) -> low
	* Note: Clearing PL8 will reset the board, so keep it up.
	*/
	sunxi_set_gpio_out('L', 5, 1);
	sunxi_set_gpio_out('L', 9, 0);
	sunxi_set_gpio_out('L', 10, 0);

	/* Turn off pin controller now. */
	mmio_write_32(SUNXI_CCU_BASE + 0x68, 0);

	break;
	case AXP803_RSB:
	/* (Re-)init RSB in case the rich OS has disabled it. */
	sunxi_init_platform_r_twi(SUNXI_SOC_A64, true);
	rsb_init();

	/* Set "power disable control" bit */
	axp_setbits(0x32, BIT(7));
	break;
	default:
	break;
	}

	udelay(1000);
	ERROR("PSCI: Cannot turn off system, halting.\n");
	wfi();
	panic();
	}