blob: 5804682c42c0db48c831517df4738d6ee23273f7 [file] [log] [blame]
/*
* Copyright (c) 2013-2014, ARM Limited and Contributors. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* Redistributions of source code must retain the above copyright notice, this
* list of conditions and the following disclaimer.
*
* Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
*
* Neither the name of ARM nor the names of its contributors may be used
* to endorse or promote products derived from this software without specific
* prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE
* LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*/
#include <arch_helpers.h>
#include <assert.h>
#include <bl_common.h>
#include <cci400.h>
#include <console.h>
#include <debug.h>
#include <mmio.h>
#include <platform.h>
#include <platform_def.h>
#include <tzc400.h>
#include "../../bl1/bl1_private.h"
#include "juno_def.h"
#include "juno_private.h"
/*******************************************************************************
* Declarations of linker defined symbols which will help us find the layout
* of trusted RAM
******************************************************************************/
extern unsigned long __COHERENT_RAM_START__;
extern unsigned long __COHERENT_RAM_END__;
/*
* The next 2 constants identify the extents of the coherent memory region.
* These addresses are used by the MMU setup code and therefore they must be
* page-aligned. It is the responsibility of the linker script to ensure that
* __COHERENT_RAM_START__ and __COHERENT_RAM_END__ linker symbols refer to
* page-aligned addresses.
*/
#define BL1_COHERENT_RAM_BASE (unsigned long)(&__COHERENT_RAM_START__)
#define BL1_COHERENT_RAM_LIMIT (unsigned long)(&__COHERENT_RAM_END__)
/* Data structure which holds the extents of the trusted RAM for BL1 */
static meminfo_t bl1_tzram_layout;
meminfo_t *bl1_plat_sec_mem_layout(void)
{
return &bl1_tzram_layout;
}
/*******************************************************************************
* Perform any BL1 specific platform actions.
******************************************************************************/
void bl1_early_platform_setup(void)
{
const size_t bl1_size = BL1_RAM_LIMIT - BL1_RAM_BASE;
/* Initialize the console to provide early debug support */
console_init(PL011_UART2_BASE, PL011_UART2_CLK_IN_HZ, PL011_BAUDRATE);
/*
* Enable CCI-400 for this cluster. No need for locks as no other cpu is
* active at the moment
*/
cci_init(CCI400_BASE,
CCI400_SL_IFACE3_CLUSTER_IX,
CCI400_SL_IFACE4_CLUSTER_IX);
cci_enable_cluster_coherency(read_mpidr());
/* Allow BL1 to see the whole Trusted RAM */
bl1_tzram_layout.total_base = TZRAM_BASE;
bl1_tzram_layout.total_size = TZRAM_SIZE;
/* Calculate how much RAM BL1 is using and how much remains free */
bl1_tzram_layout.free_base = TZRAM_BASE;
bl1_tzram_layout.free_size = TZRAM_SIZE;
reserve_mem(&bl1_tzram_layout.free_base,
&bl1_tzram_layout.free_size,
BL1_RAM_BASE,
bl1_size);
INFO("BL1: 0x%lx - 0x%lx [size = %u]\n", BL1_RAM_BASE, BL1_RAM_LIMIT,
bl1_size);
}
/*
* Address of slave 'n' security setting in the NIC-400 address region
* control
* TODO: Ideally this macro should be moved in a "nic-400.h" header file but
* it would be the only thing in there so it's not worth it at the moment.
*/
#define NIC400_ADDR_CTRL_SECURITY_REG(n) (0x8 + (n) * 4)
static void init_nic400(void)
{
/*
* NIC-400 Access Control Initialization
*
* Define access privileges by setting each corresponding bit to:
* 0 = Secure access only
* 1 = Non-secure access allowed
*/
/*
* Allow non-secure access to some SOC regions, excluding UART1, which
* remains secure.
* Note: This is the NIC-400 device on the SOC
*/
mmio_write_32(SOC_NIC400_BASE +
NIC400_ADDR_CTRL_SECURITY_REG(SOC_NIC400_USB_EHCI), ~0);
mmio_write_32(SOC_NIC400_BASE +
NIC400_ADDR_CTRL_SECURITY_REG(SOC_NIC400_TLX_MASTER), ~0);
mmio_write_32(SOC_NIC400_BASE +
NIC400_ADDR_CTRL_SECURITY_REG(SOC_NIC400_USB_OHCI), ~0);
mmio_write_32(SOC_NIC400_BASE +
NIC400_ADDR_CTRL_SECURITY_REG(SOC_NIC400_PL354_SMC), ~0);
mmio_write_32(SOC_NIC400_BASE +
NIC400_ADDR_CTRL_SECURITY_REG(SOC_NIC400_APB4_BRIDGE), ~0);
mmio_write_32(SOC_NIC400_BASE +
NIC400_ADDR_CTRL_SECURITY_REG(SOC_NIC400_BOOTSEC_BRIDGE),
~SOC_NIC400_BOOTSEC_BRIDGE_UART1);
/*
* Allow non-secure access to some CSS regions.
* Note: This is the NIC-400 device on the CSS
*/
mmio_write_32(CSS_NIC400_BASE +
NIC400_ADDR_CTRL_SECURITY_REG(CSS_NIC400_SLAVE_BOOTSECURE),
~0);
}
static void init_tzc400(void)
{
/* Enable all filter units available */
mmio_write_32(TZC400_BASE + GATE_KEEPER_OFF, 0x0000000f);
/*
* Secure read and write are enabled for region 0, and the background
* region (region 0) is enabled for all four filter units
*/
mmio_write_32(TZC400_BASE + REGION_ATTRIBUTES_OFF, 0xc0000000);
/*
* Enable Non-secure read/write accesses for the Soc Devices from the
* Non-Secure World
*/
mmio_write_32(TZC400_BASE + REGION_ID_ACCESS_OFF,
TZC_REGION_ACCESS_RDWR(TZC400_NSAID_CCI400) |
TZC_REGION_ACCESS_RDWR(TZC400_NSAID_PCIE) |
TZC_REGION_ACCESS_RDWR(TZC400_NSAID_HDLCD0) |
TZC_REGION_ACCESS_RDWR(TZC400_NSAID_HDLCD1) |
TZC_REGION_ACCESS_RDWR(TZC400_NSAID_USB) |
TZC_REGION_ACCESS_RDWR(TZC400_NSAID_DMA330) |
TZC_REGION_ACCESS_RDWR(TZC400_NSAID_THINLINKS) |
TZC_REGION_ACCESS_RDWR(TZC400_NSAID_AP) |
TZC_REGION_ACCESS_RDWR(TZC400_NSAID_GPU) |
TZC_REGION_ACCESS_RDWR(TZC400_NSAID_SCP) |
TZC_REGION_ACCESS_RDWR(TZC400_NSAID_CORESIGHT)
);
}
#define PCIE_SECURE_REG 0x3000
#define PCIE_SEC_ACCESS_MASK ((1 << 0) | (1 << 1)) /* REG and MEM access bits */
static void init_pcie(void)
{
/*
* PCIE Root Complex Security settings to enable non-secure
* access to config registers.
*/
mmio_write_32(PCIE_CONTROL_BASE + PCIE_SECURE_REG, PCIE_SEC_ACCESS_MASK);
}
/*******************************************************************************
* Function which will perform any remaining platform-specific setup that can
* occur after the MMU and data cache have been enabled.
******************************************************************************/
void bl1_platform_setup(void)
{
init_nic400();
init_tzc400();
init_pcie();
/* Initialise the IO layer and register platform IO devices */
io_setup();
/* Enable and initialize the System level generic timer */
mmio_write_32(SYS_CNTCTL_BASE + CNTCR_OFF, CNTCR_FCREQ(0) | CNTCR_EN);
}
/*******************************************************************************
* Perform the very early platform specific architecture setup here. At the
* moment this only does basic initialization. Later architectural setup
* (bl1_arch_setup()) does not do anything platform specific.
******************************************************************************/
void bl1_plat_arch_setup(void)
{
configure_mmu_el3(bl1_tzram_layout.total_base,
bl1_tzram_layout.total_size,
TZROM_BASE,
TZROM_BASE + TZROM_SIZE,
BL1_COHERENT_RAM_BASE,
BL1_COHERENT_RAM_LIMIT);
}
/*******************************************************************************
* Before calling this function BL2 is loaded in memory and its entrypoint
* is set by load_image. This is a placeholder for the platform to change
* the entrypoint of BL2 and set SPSR and security state.
* On Juno we are only setting the security state, entrypoint
******************************************************************************/
void bl1_plat_set_bl2_ep_info(image_info_t *bl2_image,
entry_point_info_t *bl2_ep)
{
SET_SECURITY_STATE(bl2_ep->h.attr, SECURE);
bl2_ep->spsr = SPSR_64(MODE_EL1, MODE_SP_ELX, DISABLE_ALL_EXCEPTIONS);
}