| /* |
| * Copyright (c) 2013-2014, ARM Limited and Contributors. All rights reserved. |
| * |
| * SPDX-License-Identifier: BSD-3-Clause |
| */ |
| |
| #ifndef __PL011_H__ |
| #define __PL011_H__ |
| |
| /* PL011 Registers */ |
| #define UARTDR 0x000 |
| #define UARTRSR 0x004 |
| #define UARTECR 0x004 |
| #define UARTFR 0x018 |
| #define UARTIMSC 0x038 |
| #define UARTRIS 0x03C |
| #define UARTICR 0x044 |
| |
| /* PL011 registers (out of the SBSA specification) */ |
| #if !PL011_GENERIC_UART |
| #define UARTILPR 0x020 |
| #define UARTIBRD 0x024 |
| #define UARTFBRD 0x028 |
| #define UARTLCR_H 0x02C |
| #define UARTCR 0x030 |
| #define UARTIFLS 0x034 |
| #define UARTMIS 0x040 |
| #define UARTDMACR 0x048 |
| #endif /* !PL011_GENERIC_UART */ |
| |
| /* Data status bits */ |
| #define UART_DATA_ERROR_MASK 0x0F00 |
| |
| /* Status reg bits */ |
| #define UART_STATUS_ERROR_MASK 0x0F |
| |
| /* Flag reg bits */ |
| #define PL011_UARTFR_RI (1 << 8) /* Ring indicator */ |
| #define PL011_UARTFR_TXFE (1 << 7) /* Transmit FIFO empty */ |
| #define PL011_UARTFR_RXFF (1 << 6) /* Receive FIFO full */ |
| #define PL011_UARTFR_TXFF (1 << 5) /* Transmit FIFO full */ |
| #define PL011_UARTFR_RXFE (1 << 4) /* Receive FIFO empty */ |
| #define PL011_UARTFR_BUSY (1 << 3) /* UART busy */ |
| #define PL011_UARTFR_DCD (1 << 2) /* Data carrier detect */ |
| #define PL011_UARTFR_DSR (1 << 1) /* Data set ready */ |
| #define PL011_UARTFR_CTS (1 << 0) /* Clear to send */ |
| |
| #define PL011_UARTFR_TXFF_BIT 5 /* Transmit FIFO full bit in UARTFR register */ |
| #define PL011_UARTFR_RXFE_BIT 4 /* Receive FIFO empty bit in UARTFR register */ |
| #define PL011_UARTFR_BUSY_BIT 3 /* UART busy bit in UARTFR register */ |
| |
| /* Control reg bits */ |
| #if !PL011_GENERIC_UART |
| #define PL011_UARTCR_CTSEN (1 << 15) /* CTS hardware flow control enable */ |
| #define PL011_UARTCR_RTSEN (1 << 14) /* RTS hardware flow control enable */ |
| #define PL011_UARTCR_RTS (1 << 11) /* Request to send */ |
| #define PL011_UARTCR_DTR (1 << 10) /* Data transmit ready. */ |
| #define PL011_UARTCR_RXE (1 << 9) /* Receive enable */ |
| #define PL011_UARTCR_TXE (1 << 8) /* Transmit enable */ |
| #define PL011_UARTCR_LBE (1 << 7) /* Loopback enable */ |
| #define PL011_UARTCR_UARTEN (1 << 0) /* UART Enable */ |
| |
| #if !defined(PL011_LINE_CONTROL) |
| /* FIFO Enabled / No Parity / 8 Data bit / One Stop Bit */ |
| #define PL011_LINE_CONTROL (PL011_UARTLCR_H_FEN | PL011_UARTLCR_H_WLEN_8) |
| #endif |
| |
| /* Line Control Register Bits */ |
| #define PL011_UARTLCR_H_SPS (1 << 7) /* Stick parity select */ |
| #define PL011_UARTLCR_H_WLEN_8 (3 << 5) |
| #define PL011_UARTLCR_H_WLEN_7 (2 << 5) |
| #define PL011_UARTLCR_H_WLEN_6 (1 << 5) |
| #define PL011_UARTLCR_H_WLEN_5 (0 << 5) |
| #define PL011_UARTLCR_H_FEN (1 << 4) /* FIFOs Enable */ |
| #define PL011_UARTLCR_H_STP2 (1 << 3) /* Two stop bits select */ |
| #define PL011_UARTLCR_H_EPS (1 << 2) /* Even parity select */ |
| #define PL011_UARTLCR_H_PEN (1 << 1) /* Parity Enable */ |
| #define PL011_UARTLCR_H_BRK (1 << 0) /* Send break */ |
| |
| #endif /* !PL011_GENERIC_UART */ |
| |
| #endif /* __PL011_H__ */ |