/dts-v1/;
#include "mt7986a.dtsi"
#include "mt7986a-pinctrl.dtsi"
#include "mt7986-spim-nand-partition.dtsi"
/ {
	model = "MediaTek MT7986a gsw RFB";
	compatible = "mediatek,mt7986a-2500wan-gsw-spim-snand-rfb";
	chosen {
		bootargs = "console=ttyS0,115200n1 loglevel=8  \
				earlycon=uart8250,mmio32,0x11002000";
	};

	gsw: gsw@0 {
		compatible = "mediatek,mt753x";
		mediatek,ethsys = <&ethsys>;
		#address-cells = <1>;
		#size-cells = <0>;
	};

	memory {
		reg = <0 0x40000000 0 0x10000000>;
	};

	sound {
		compatible = "mediatek,mt7986-wm8960-machine";
		mediatek,platform = <&afe>;
		audio-routing = "Headphone", "HP_L",
				"Headphone", "HP_R",
				"LINPUT1", "AMIC",
				"RINPUT1", "AMIC";
		mediatek,audio-codec = <&wm8960>;
		status = "okay";
	};
};

&fan {
	pwms = <&pwm 1 50000 0>;
	status = "disabled";
};

&pwm {
	pinctrl-names = "default";
	pinctrl-0 = <&pwm0_pin &pwm1_pin_g1>;
	status = "okay";
};

&uart0 {
	status = "okay";
};

&uart1 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart1_pins>;
	status = "okay";
};

&uart2 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart2_pins>;
	status = "disabled";
};

&i2c0 {
	pinctrl-names = "default";
	pinctrl-0 = <&i2c_pins>;
	status = "okay";

	wm8960: wm8960@1a {
		compatible = "wlf,wm8960";
		reg = <0x1a>;
	};
};

&auxadc {
	status = "okay";
};

&watchdog {
	status = "okay";
};

&eth {
	status = "okay";

	gmac0: mac@0 {
		compatible = "mediatek,eth-mac";
		reg = <0>;
		phy-mode = "2500base-x";
		phy-handle = <&phy5>;
	};

	gmac1: mac@1 {
		compatible = "mediatek,eth-mac";
		reg = <1>;
		phy-mode = "2500base-x";
		phy-handle = <&phy6>;
	};

	mdio: mdio-bus {
		#address-cells = <1>;
		#size-cells = <0>;

		reset-gpios = <&pio 6 1>;
		reset-delay-us = <600>;

		phy5: phy@5 {
			compatible = "ethernet-phy-ieee802.3-c45";
			reg = <5>;
		};

		phy6: phy@6 {
			compatible = "ethernet-phy-ieee802.3-c45";
			reg = <6>;
		};
	};
};

&gsw {
	mediatek,mdio = <&mdio>;
	mediatek,portmap = "lllll";
	mediatek,mdio_master_pinmux = <1>;
	reset-gpios = <&pio 5 0>;
	interrupt-parent = <&pio>;
	interrupts = <66 IRQ_TYPE_LEVEL_HIGH>;
	status = "okay";

	port5: port@5 {
		compatible = "mediatek,mt753x-port";
		reg = <5>;
		phy-mode = "sgmii";

		fixed-link {
			speed = <2500>;
			full-duplex;
		};

	};

	port6: port@6 {
		compatible = "mediatek,mt753x-port";
		/* mediatek,ssc-on; */
		reg = <6>;
		phy-mode = "sgmii";
		fixed-link {
			speed = <2500>;
			full-duplex;
		};
	};
};

&hnat {
	mtketh-wan = "eth1";
	mtketh-lan = "eth0";
	mtketh-max-gmac = <2>;
	status = "okay";
};

&spi0 {
	pinctrl-names = "default";
	pinctrl-0 = <&spi_flash_pins>;
	cs-gpios = <0>, <0>;
	status = "okay";

	spi_nor@0 {
		#address-cells = <1>;
		#size-cells = <1>;
		compatible = "jedec,spi-nor";
		reg = <0>;
		spi-max-frequency = <20000000>;
		spi-tx-buswidth = <4>;
		spi-rx-buswidth = <4>;
	};

	spi_nand: spi_nand@1 {
		#address-cells = <1>;
		#size-cells = <1>;
		compatible = "spi-nand";
		reg = <1>;
		spi-max-frequency = <20000000>;
		spi-tx-buswidth = <4>;
		spi-rx-buswidth = <4>;
	};
};

&spi1 {
	pinctrl-names = "default";
	pinctrl-0 = <&spic_pins_g2>;
	status = "okay";
};

&pcie0 {
	pinctrl-names = "default";
	pinctrl-0 = <&pcie0_pins>;
	status = "okay";
};

&wbsys {
	mediatek,mtd-eeprom = <&factory 0x0000>;
	status = "okay";
};

&pio {
	spi_flash_pins: spi-flash-pins-33-to-38 {
		mux {
			function = "flash";
			groups = "spi0", "spi0_wp_hold";
		};
		conf-pu {
			pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
			drive-strength = <MTK_DRIVE_8mA>;
			bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
		};
		conf-pd {
			pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
			drive-strength = <MTK_DRIVE_8mA>;
			bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
		};
	};
};