Blame - drivers/usb/host/Kconfig - filogic/uboot

blob: 42e8a9f934fb0a50d16e1600d8fd3c299ef4260a [file] [log] [blame]

Masahiro Yamada	1b0a06b	2014-11-07 18:48:31 +0900	[diff] [blame]	1	#
				2	# USB Host Controller Drivers
				3	#
				4	comment "USB Host Controller Drivers"
				5
Masahiro Yamada	59cfdc0	2016-08-01 00:16:34 +0900	[diff] [blame]	6	config USB_HOST
				7	bool
				8
Masahiro Yamada	1b0a06b	2014-11-07 18:48:31 +0900	[diff] [blame]	9	config USB_XHCI_HCD
				10	bool "xHCI HCD (USB 3.0) support"
Masahiro Yamada	59cfdc0	2016-08-01 00:16:34 +0900	[diff] [blame]	11	select USB_HOST
Masahiro Yamada	1b0a06b	2014-11-07 18:48:31 +0900	[diff] [blame]	12	---help---
				13	The eXtensible Host Controller Interface (xHCI) is standard for USB 3.0
				14	"SuperSpeed" host controller hardware.
				15
Masahiro Yamada	1b0a06b	2014-11-07 18:48:31 +0900	[diff] [blame]	16	if USB_XHCI_HCD
				17
Masahiro Yamada	d3b72ca	2016-06-04 07:35:04 +0900	[diff] [blame]	18	config USB_XHCI_DWC3
				19	bool "DesignWare USB3 DRD Core Support"
				20	help
				21	Say Y or if your system has a Dual Role SuperSpeed
				22	USB controller based on the DesignWare USB3 IP Core.
				23
Masahiro Yamada	78a9c79	2016-08-01 00:16:32 +0900	[diff] [blame]	24	endif # USB_XHCI_HCD
Alexey Brodkin	83fd312	2015-12-14 17:18:50 +0300	[diff] [blame]	25
Masahiro Yamada	1b0a06b	2014-11-07 18:48:31 +0900	[diff] [blame]	26	config USB_EHCI_HCD
				27	bool "EHCI HCD (USB 2.0) support"
Masahiro Yamada	59cfdc0	2016-08-01 00:16:34 +0900	[diff] [blame]	28	select USB_HOST
Masahiro Yamada	1b0a06b	2014-11-07 18:48:31 +0900	[diff] [blame]	29	---help---
				30	The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0
				31	"high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware.
				32	If your USB host controller supports USB 2.0, you will likely want to
				33	configure this Host Controller Driver.
				34
				35	EHCI controllers are packaged with "companion" host controllers (OHCI
				36	or UHCI) to handle USB 1.1 devices connected to root hub ports. Ports
				37	will connect to EHCI if the device is high speed, otherwise they
				38	connect to a companion controller. If you configure EHCI, you should
				39	probably configure the OHCI (for NEC and some other vendors) USB Host
				40	Controller Driver or UHCI (for Via motherboards) Host Controller
				41	Driver too.
				42
				43	You may want to read <file:Documentation/usb/ehci.txt>.
				44
				45	config USB_EHCI
				46	bool
				47	default USB_EHCI_HCD
				48	---help---
				49	TODO: rename after most boards switch to Kconfig
				50
				51	if USB_EHCI_HCD
				52
Wenyou Yang	11e2665	2016-08-05 08:57:35 +0800	[diff] [blame]	53	config USB_EHCI_ATMEL
				54	bool "Support for Atmel on-chip EHCI USB controller"
				55	depends on ARCH_AT91
				56	default y
				57	---help---
				58	Enables support for the on-chip EHCI controller on Atmel chips.
				59
Stefan Roese	0390102	2015-09-01 11:39:44 +0200	[diff] [blame]	60	config USB_EHCI_MARVELL
				61	bool "Support for MVEBU (AXP / A38x) on-chip EHCI USB controller"
				62	depends on ARCH_MVEBU
				63	default y
				64	---help---
				65	Enables support for the on-chip EHCI controller on MVEBU SoCs.
				66
Nikita Kiryanov	9924103	2015-07-23 17:19:35 +0300	[diff] [blame]	67	config USB_EHCI_MX6
				68	bool "Support for i.MX6 on-chip EHCI USB controller"
				69	depends on ARCH_MX6
				70	default y
				71	---help---
				72	Enables support for the on-chip EHCI controller on i.MX6 SoCs.
				73
Stefan Agner	100fe07	2016-07-13 00:25:36 -0700	[diff] [blame]	74	config USB_EHCI_MX7
				75	bool "Support for i.MX7 on-chip EHCI USB controller"
				76	depends on ARCH_MX7
				77	default y
				78	---help---
				79	Enables support for the on-chip EHCI controller on i.MX7 SoCs.
				80
Stefan Agner	8652ce9	2016-07-13 00:25:38 -0700	[diff] [blame]	81	if USB_EHCI_MX7
				82
				83	config MXC_USB_OTG_HACTIVE
				84	bool "USB Power pin high active"
				85	---help---
				86	Set the USB Power pin polarity to be high active (PWR_POL)
				87
				88	endif
				89
Mateusz Kulikowski	dc38117	2016-03-31 23:12:26 +0200	[diff] [blame]	90	config USB_EHCI_MSM
				91	bool "Support for Qualcomm on-chip EHCI USB controller"
				92	depends on DM_USB
				93	select USB_ULPI_VIEWPORT
				94	default n
				95	---help---
				96	Enables support for the on-chip EHCI controller on Qualcomm
				97	Snapdragon SoCs.
				98	This driver supports combination of Chipidea USB controller
				99	and Synapsys USB PHY in host mode only.
				100
Siva Durga Prasad Paladugu	42fcc18	2016-07-22 14:51:51 +0530	[diff] [blame]	101	config USB_EHCI_ZYNQ
				102	bool "Support for Xilinx Zynq on-chip EHCI USB controller"
				103	depends on ARCH_ZYNQ
				104	default y
				105	---help---
				106	Enable support for Zynq on-chip EHCI USB controller
				107
Alexey Brodkin	a6aff43	2015-12-02 12:32:02 +0300	[diff] [blame]	108	config USB_EHCI_GENERIC
				109	bool "Support for generic EHCI USB controller"
				110	depends on OF_CONTROL
				111	depends on DM_USB
				112	default n
				113	---help---
				114	Enables support for generic EHCI controller.
				115
Masahiro Yamada	78a9c79	2016-08-01 00:16:32 +0900	[diff] [blame]	116	endif # USB_EHCI_HCD
				117
				118	config USB_OHCI_HCD
				119	bool "OHCI HCD (USB 1.1) support"
				120	---help---
				121	The Open Host Controller Interface (OHCI) is a standard for accessing
				122	USB 1.1 host controller hardware. It does more in hardware than Intel's
				123	UHCI specification. If your USB host controller follows the OHCI spec,
				124	say Y. On most non-x86 systems, and on x86 hardware that's not using a
				125	USB controller from Intel or VIA, this is appropriate. If your host
				126	controller doesn't use PCI, this is probably appropriate. For a PCI
				127	based system where you're not sure, the "lspci -v" entry will list the
				128	right "prog-if" for your USB controller(s): EHCI, OHCI, or UHCI.
				129
				130	if USB_OHCI_HCD
				131
				132	config USB_OHCI_GENERIC
				133	bool "Support for generic OHCI USB controller"
				134	depends on OF_CONTROL
				135	depends on DM_USB
Masahiro Yamada	59cfdc0	2016-08-01 00:16:34 +0900	[diff] [blame]	136	select USB_HOST
Masahiro Yamada	78a9c79	2016-08-01 00:16:32 +0900	[diff] [blame]	137	---help---
				138	Enables support for generic OHCI controller.
				139
				140	endif # USB_OHCI_HCD
Masahiro Yamada	718ba3c	2016-08-01 00:16:33 +0900	[diff] [blame]	141
				142	config USB_UHCI_HCD
				143	bool "UHCI HCD (most Intel and VIA) support"
Masahiro Yamada	59cfdc0	2016-08-01 00:16:34 +0900	[diff] [blame]	144	select USB_HOST
Masahiro Yamada	718ba3c	2016-08-01 00:16:33 +0900	[diff] [blame]	145	---help---
				146	The Universal Host Controller Interface is a standard by Intel for
				147	accessing the USB hardware in the PC (which is also called the USB
				148	host controller). If your USB host controller conforms to this
				149	standard, you may want to say Y, but see below. All recent boards
				150	with Intel PCI chipsets (like intel 430TX, 440FX, 440LX, 440BX,
				151	i810, i820) conform to this standard. Also all VIA PCI chipsets
				152	(like VIA VP2, VP3, MVP3, Apollo Pro, Apollo Pro II or Apollo Pro
				153	133) and LEON/GRLIB SoCs with the GRUSBHC controller.
				154	If unsure, say Y.
				155
				156	if USB_UHCI_HCD
				157
				158	endif # USB_UHCI_HCD