| Tom Wai-Hong Tam | 2ab5695 | 2014-05-20 06:01:36 -0600 | [diff] [blame] | 1 | TPS65090 regulators |
| 2 | |
| 3 | Required properties: |
| 4 | - compatible: "ti,tps65090" |
| 5 | - reg: I2C slave address |
| 6 | - interrupts: the interrupt outputs of the controller |
| 7 | - regulators: A node that houses a sub-node for each regulator within the |
| 8 | device. Each sub-node is identified using the node's name, with valid |
| 9 | values listed below. The content of each sub-node is defined by the |
| 10 | standard binding for regulators; see regulator.txt. |
| 11 | dcdc[1-3], fet[1-7] and ldo[1-2] respectively. |
| 12 | - vsys[1-3]-supply: The input supply for DCDC[1-3] respectively. |
| 13 | - infet[1-7]-supply: The input supply for FET[1-7] respectively. |
| 14 | - vsys-l[1-2]-supply: The input supply for LDO[1-2] respectively. |
| 15 | |
| 16 | Optional properties: |
| 17 | - ti,enable-ext-control: This is applicable for DCDC1, DCDC2 and DCDC3. |
| 18 | If DCDCs are externally controlled then this property should be there. |
| 19 | - "dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3. |
| 20 | If DCDCs are externally controlled and if it is from GPIO then GPIO |
| 21 | number should be provided. If it is externally controlled and no GPIO |
| 22 | entry then driver will just configure this rails as external control |
| 23 | and will not provide any enable/disable APIs. |
| 24 | |
| 25 | Each regulator is defined using the standard binding for regulators. |
| 26 | |
| 27 | Example: |
| 28 | |
| 29 | tps65090@48 { |
| 30 | compatible = "ti,tps65090"; |
| 31 | reg = <0x48>; |
| 32 | interrupts = <0 88 0x4>; |
| 33 | |
| 34 | vsys1-supply = <&some_reg>; |
| 35 | vsys2-supply = <&some_reg>; |
| 36 | vsys3-supply = <&some_reg>; |
| 37 | infet1-supply = <&some_reg>; |
| 38 | infet2-supply = <&some_reg>; |
| 39 | infet3-supply = <&some_reg>; |
| 40 | infet4-supply = <&some_reg>; |
| 41 | infet5-supply = <&some_reg>; |
| 42 | infet6-supply = <&some_reg>; |
| 43 | infet7-supply = <&some_reg>; |
| 44 | vsys_l1-supply = <&some_reg>; |
| 45 | vsys_l2-supply = <&some_reg>; |
| 46 | |
| 47 | regulators { |
| 48 | dcdc1 { |
| 49 | regulator-name = "dcdc1"; |
| 50 | regulator-boot-on; |
| 51 | regulator-always-on; |
| 52 | ti,enable-ext-control; |
| 53 | dcdc-ext-control-gpios = <&gpio 10 0>; |
| 54 | }; |
| 55 | |
| 56 | dcdc2 { |
| 57 | regulator-name = "dcdc2"; |
| 58 | regulator-boot-on; |
| 59 | regulator-always-on; |
| 60 | }; |
| 61 | |
| 62 | dcdc3 { |
| 63 | regulator-name = "dcdc3"; |
| 64 | regulator-boot-on; |
| 65 | regulator-always-on; |
| 66 | }; |
| 67 | |
| 68 | fet1 { |
| 69 | regulator-name = "fet1"; |
| 70 | regulator-boot-on; |
| 71 | regulator-always-on; |
| 72 | }; |
| 73 | |
| 74 | fet2 { |
| 75 | regulator-name = "fet2"; |
| 76 | regulator-boot-on; |
| 77 | regulator-always-on; |
| 78 | }; |
| 79 | |
| 80 | fet3 { |
| 81 | regulator-name = "fet3"; |
| 82 | regulator-boot-on; |
| 83 | regulator-always-on; |
| 84 | }; |
| 85 | |
| 86 | fet4 { |
| 87 | regulator-name = "fet4"; |
| 88 | regulator-boot-on; |
| 89 | regulator-always-on; |
| 90 | }; |
| 91 | |
| 92 | fet5 { |
| 93 | regulator-name = "fet5"; |
| 94 | regulator-boot-on; |
| 95 | regulator-always-on; |
| 96 | }; |
| 97 | |
| 98 | fet6 { |
| 99 | regulator-name = "fet6"; |
| 100 | regulator-boot-on; |
| 101 | regulator-always-on; |
| 102 | }; |
| 103 | |
| 104 | fet7 { |
| 105 | regulator-name = "fet7"; |
| 106 | regulator-boot-on; |
| 107 | regulator-always-on; |
| 108 | }; |
| 109 | |
| 110 | ldo1 { |
| 111 | regulator-name = "ldo1"; |
| 112 | regulator-boot-on; |
| 113 | regulator-always-on; |
| 114 | }; |
| 115 | |
| 116 | ldo2 { |
| 117 | regulator-name = "ldo2"; |
| 118 | regulator-boot-on; |
| 119 | regulator-always-on; |
| 120 | }; |
| 121 | }; |
| 122 | }; |