board/siemens/capricorn/board.c - filogic/uboot - Gitiles

 // SPDX-License-Identifier: GPL-2.0+
 /*
  * Copyright 2017-2019 NXP
  *
  * Copyright 2019 Siemens AG
  *
  */
 #include <common.h>
 #include <command.h>
 #include <dm.h>
 #include <env.h>
 #include <errno.h>
 #include <init.h>
 #include <log.h>
 #include <netdev.h>
 #include <env_internal.h>
 #include <fsl_esdhc_imx.h>
 #include <i2c.h>
 #include <led.h>
 #include <pca953x.h>
 #include <power-domain.h>
 #include <asm/gpio.h>
 #include <asm/arch/imx8-pins.h>
 #include <asm/arch/iomux.h>
 #include <firmware/imx/sci/sci.h>
 #include <asm/arch/sys_proto.h>
 #ifndef CONFIG_SPL
 #include <asm/arch-imx8/clock.h>
 #endif
 #include <linux/delay.h>
 #include "../common/factoryset.h"

 #define GPIO_PAD_CTRL \
 		((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \
 		 (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
 		 (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
 		 (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))

 #define ENET_NORMAL_PAD_CTRL \
 		((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \
 		 (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
 		 (SC_PAD_28FDSOI_DSE_18V_10MA << PADRING_DSE_SHIFT) | \
 		 (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))

 #define UART_PAD_CTRL \
 		((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \
 		 (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
 		 (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
 		 (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))

 static iomux_cfg_t uart2_pads[] = {
 	SC_P_UART2_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
 	SC_P_UART2_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
 };

 static void setup_iomux_uart(void)
 {
 	imx8_iomux_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
 }

 int board_early_init_f(void)
 {
 	/* Set UART clock root to 80 MHz */
 	sc_pm_clock_rate_t rate = SC_80MHZ;
 	int ret;

 	ret = sc_pm_setup_uart(SC_R_UART_0, rate);
 	ret |= sc_pm_setup_uart(SC_R_UART_2, rate);
 	if (ret)
 		return ret;

 	setup_iomux_uart();

 	return 0;
 }

 #define ENET_PHY_RESET	IMX_GPIO_NR(0, 3)
 #define ENET_TEST_1	IMX_GPIO_NR(0, 8)
 #define ENET_TEST_2	IMX_GPIO_NR(0, 9)

 /*#define ETH_IO_TEST*/
 static iomux_cfg_t enet_reset[] = {
 	SC_P_ESAI0_SCKT | MUX_MODE_ALT(4) | MUX_PAD_CTRL(GPIO_PAD_CTRL),
 #ifdef ETH_IO_TEST
 	/* GPIO0.IO08 MODE3: TXD0 */
 	SC_P_ESAI0_TX4_RX1 | MUX_MODE_ALT(4) |
 	MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL),
 	/* GPIO0.IO09 MODE3: TXD1 */
 	SC_P_ESAI0_TX5_RX0 | MUX_MODE_ALT(4) |
 	MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL),
 #endif
 };

 static void enet_device_phy_reset(void)
 {
 	int ret = 0;

 	imx8_iomux_setup_multiple_pads(enet_reset, ARRAY_SIZE(enet_reset));

 	ret = gpio_request(ENET_PHY_RESET, "enet_phy_reset");
 	if (!ret) {
 		gpio_direction_output(ENET_PHY_RESET, 1);
 		gpio_set_value(ENET_PHY_RESET, 0);
 		/* SMSC9303 TRM chapter 14.5.2 */
 		udelay(200);
 		gpio_set_value(ENET_PHY_RESET, 1);
 	} else {
 		printf("ENET RESET failed!\n");
 	}

 #ifdef ETH_IO_TEST
 	ret =  gpio_request(ENET_TEST_1, "enet_test1");
 	if (!ret) {
 		int i;

 		printf("ENET TEST 1!\n");
 		for (i = 0; i < 20; i++) {
 			gpio_direction_output(ENET_TEST_1, 1);
 			gpio_set_value(ENET_TEST_1, 0);
 			udelay(50);
 			gpio_set_value(ENET_TEST_1, 1);
 			udelay(50);
 		}
 		gpio_free(ENET_TEST_1);
 	} else {
 		printf("GPIO for ENET TEST 1 failed!\n");
 	}
 	ret =  gpio_request(ENET_TEST_2, "enet_test2");
 	if (!ret) {
 		int i;

 		printf("ENET TEST 2!\n");
 		for (i = 0; i < 20; i++) {
 			gpio_direction_output(ENET_TEST_2, 1);
 			gpio_set_value(ENET_TEST_2, 0);
 			udelay(50);
 			gpio_set_value(ENET_TEST_2, 1);
 			udelay(50);
 		}
 		gpio_free(ENET_TEST_2);
 	} else {
 		printf("GPIO for ENET TEST 2 failed!\n");
 	}
 #endif
 }

 int setup_gpr_fec(void)
 {
 	sc_ipc_t ipc_handle = -1;
 	int err = 0;
 	unsigned int test;

 	/*
 	 * TX_CLK_SEL: it controls a mux between clock coming from the pad 50M
 	 * input pin and clock generated internally to connectivity subsystem
 	 *	0: internal clock
 	 *	1: external clock --->  your choice for RMII
 	 *
 	 * CLKDIV_SEL: it controls a div by 2 on the internal clock path à
 	 *	it should be don’t care when using external clock
 	 *	0: non-divided clock
 	 *	1: clock divided by 2
 	 * 50_DISABLE or 125_DISABLE:
 	 *	it’s used to disable the clock tree going outside the chip
 	 *	when reference clock is generated internally.
 	 *	It should be don’t care when reference clock is provided
 	 *	externally.
 	 *	0: clock is enabled
 	 *	1: clock is disabled
 	 *
 	 * SC_C_TXCLK		= 24,
 	 * SC_C_CLKDIV		= 25,
 	 * SC_C_DISABLE_50	= 26,
 	 * SC_C_DISABLE_125	= 27,
 	 */

 	err = sc_misc_set_control(ipc_handle, SC_R_ENET_1, SC_C_TXCLK, 1);
 	if (err)
 		printf("Error in setting up SC_C %d\n\r", SC_C_TXCLK);

 	sc_misc_get_control(ipc_handle, SC_R_ENET_1, SC_C_TXCLK, &test);
 	debug("TEST SC_C %d-->%d\n\r", SC_C_TXCLK, test);

 	err = sc_misc_set_control(ipc_handle, SC_R_ENET_1, SC_C_CLKDIV, 0);
 	if (err)
 		printf("Error in setting up SC_C %d\n\r", SC_C_CLKDIV);

 	sc_misc_get_control(ipc_handle, SC_R_ENET_1, SC_C_CLKDIV, &test);
 	debug("TEST SC_C %d-->%d\n\r", SC_C_CLKDIV, test);

 	err = sc_misc_set_control(ipc_handle, SC_R_ENET_1, SC_C_DISABLE_50, 0);
 	if (err)
 		printf("Error in setting up SC_C %d\n\r", SC_C_DISABLE_50);

 	sc_misc_get_control(ipc_handle, SC_R_ENET_1, SC_C_TXCLK, &test);
 	debug("TEST SC_C %d-->%d\n\r", SC_C_DISABLE_50, test);

 	err = sc_misc_set_control(ipc_handle, SC_R_ENET_1, SC_C_DISABLE_125, 1);
 	if (err)
 		printf("Error in setting up SC_C %d\n\r", SC_C_DISABLE_125);

 	sc_misc_get_control(ipc_handle, SC_R_ENET_1, SC_C_TXCLK, &test);
 	debug("TEST SC_C %d-->%d\n\r", SC_C_DISABLE_125, test);

 	err = sc_misc_set_control(ipc_handle, SC_R_ENET_1, SC_C_SEL_125, 1);
 	if (err)
 		printf("Error in setting up SC_C %d\n\r", SC_C_SEL_125);

 	sc_misc_get_control(ipc_handle, SC_R_ENET_1, SC_C_SEL_125, &test);
 	debug("TEST SC_C %d-->%d\n\r", SC_C_SEL_125, test);

 	return 0;
 }

 #if IS_ENABLED(CONFIG_FEC_MXC)
 #include <miiphy.h>
 int board_phy_config(struct phy_device *phydev)
 {
 	if (phydev->drv->config)
 		phydev->drv->config(phydev);

 	return 0;
 }

 #endif

 static int setup_fec(void)
 {
 	setup_gpr_fec();
 	/* Reset ENET PHY */
 	enet_device_phy_reset();
 	return 0;
 }

 void reset_cpu(void)
 {
 }

 #ifndef CONFIG_SPL_BUILD
 /* LED's */
 static int board_led_init(void)
 {
 	struct udevice *bus, *dev;
 	u8 pca_led[2] = { 0x00, 0x00 };
 	int ret;

 	/* enable all leds on PCA9552 */
 	ret = uclass_get_device_by_seq(UCLASS_I2C, PCA9552_1_I2C_BUS, &bus);
 	if (ret) {
 		printf("ERROR: I2C get %d\n", ret);
 		return ret;
 	}

 	ret = dm_i2c_probe(bus, PCA9552_1_I2C_ADDR, 0, &dev);
 	if (ret) {
 		printf("ERROR: PCA9552 probe failed\n");
 		return ret;
 	}

 	ret = dm_i2c_write(dev, 0x16, pca_led, sizeof(pca_led));
 	if (ret) {
 		printf("ERROR: PCA9552 write failed\n");
 		return ret;
 	}

 	mdelay(1);
 	return ret;
 }
 #endif /* !CONFIG_SPL_BUILD */

 int checkboard(void)
 {
 	puts("Board: Capricorn\n");

 	/*
 	 * Running build_info() doesn't work with current SCFW blob.
 	 * Uncomment below call when new blob is available.
 	 */
 	/*build_info();*/

 	print_bootinfo();
 	return 0;
 }

 int board_init(void)
 {
 	setup_fec();
 	return 0;
 }

 #ifdef CONFIG_OF_BOARD_SETUP
 int ft_board_setup(void *blob, struct bd_info *bd)
 {
 	return 0;
 }
 #endif

 int board_mmc_get_env_dev(int devno)
 {
 	return devno;
 }

 static int check_mmc_autodetect(void)
 {
 	char *autodetect_str = env_get("mmcautodetect");

 	if (autodetect_str && (strcmp(autodetect_str, "yes") == 0))
 		return 1;

 	return 0;
 }

 /* This should be defined for each board */
 __weak int mmc_map_to_kernel_blk(int dev_no)
 {
 	return dev_no;
 }

 void board_late_mmc_env_init(void)
 {
 	char cmd[32];
 	char mmcblk[32];
 	u32 dev_no = mmc_get_env_dev();

 	if (!check_mmc_autodetect())
 		return;

 	env_set_ulong("mmcdev", dev_no);

 	/* Set mmcblk env */
 	sprintf(mmcblk, "/dev/mmcblk%dp2 rootwait rw",
 		mmc_map_to_kernel_blk(dev_no));
 	env_set("mmcroot", mmcblk);

 	sprintf(cmd, "mmc dev %d", dev_no);
 	run_command(cmd, 0);
 }

 #ifndef CONFIG_SPL_BUILD
 int factoryset_read_eeprom(int i2c_addr);

 static int load_parameters_from_factoryset(void)
 {
 	int ret;

 	ret = factoryset_read_eeprom(EEPROM_I2C_ADDR);
 	if (ret)
 		return ret;

 	return factoryset_env_set();
 }

 int board_late_init(void)
 {
 	env_set("sec_boot", "no");
 #ifdef CONFIG_AHAB_BOOT
 	env_set("sec_boot", "yes");
 #endif

 #ifdef CONFIG_ENV_IS_IN_MMC
 	board_late_mmc_env_init();
 #endif
 	/* Init LEDs */
 	if (board_led_init())
 		printf("I2C LED init failed\n");

 	/* Set environment from factoryset */
 	if (load_parameters_from_factoryset())
 		printf("Loading factoryset parameters failed!\n");

 	return 0;
 }

 /* Service button */
 #define MAX_PIN_NUMBER			128
 #define BOARD_DEFAULT_BUTTON_GPIO	IMX_GPIO_NR(1, 31)

 unsigned char get_button_state(char * const envname, unsigned char def)
 {
 	int button = 0;
 	int gpio;
 	char *ptr_env;

 	/* If button is not found we take default */
 	ptr_env = env_get(envname);
 	if (!ptr_env) {
 		printf("Using default: %u\n", def);
 		gpio = def;
 	} else {
 		gpio = (unsigned char)simple_strtoul(ptr_env, NULL, 0);
 		if (gpio > MAX_PIN_NUMBER)
 			gpio = def;
 	}

 	gpio_request(gpio, "");
 	gpio_direction_input(gpio);
 	if (gpio_get_value(gpio))
 		button = 1;
 	else
 		button = 0;

 	gpio_free(gpio);

 	return button;
 }

 /*
  * This command returns the status of the user button on
  * Input - none
  * Returns -	1 if button is held down
  *		0 if button is not held down
  */
 static int
 do_userbutton(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[])
 {
 	int button = 0;

 	button = get_button_state("button_usr1", BOARD_DEFAULT_BUTTON_GPIO);

 	if (argc > 1)
 		printf("Button state: %u\n", button);

 	return button;
 }

 U_BOOT_CMD(
 	usrbutton, CONFIG_SYS_MAXARGS, 2, do_userbutton,
 	"Return the status of user button",
 	"[print]"
 );

 #define ERST	IMX_GPIO_NR(0, 3)

 static int
 do_eth_reset(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[])
 {
 	gpio_request(ERST, "ERST");
 	gpio_direction_output(ERST, 0);
 	udelay(200);
 	gpio_set_value(ERST, 1);
 	return 0;
 }

 U_BOOT_CMD(
 	switch_rst, CONFIG_SYS_MAXARGS, 2, do_eth_reset,
 	"Reset eth phy",
 	"[print]"
 );
 #endif /* ! CONFIG_SPL_BUILD */
	// SPDX-License-Identifier: GPL-2.0+
	/*
	* Copyright 2017-2019 NXP
	*
	* Copyright 2019 Siemens AG
	*
	*/
	#include <common.h>
	#include <command.h>
	#include <dm.h>
	#include <env.h>
	#include <errno.h>
	#include <init.h>
	#include <log.h>
	#include <netdev.h>
	#include <env_internal.h>
	#include <fsl_esdhc_imx.h>
	#include <i2c.h>
	#include <led.h>
	#include <pca953x.h>
	#include <power-domain.h>
	#include <asm/gpio.h>
	#include <asm/arch/imx8-pins.h>
	#include <asm/arch/iomux.h>
	#include <firmware/imx/sci/sci.h>
	#include <asm/arch/sys_proto.h>
	#ifndef CONFIG_SPL
	#include <asm/arch-imx8/clock.h>
	#endif
	#include <linux/delay.h>
	#include "../common/factoryset.h"

	#define GPIO_PAD_CTRL \
	((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) \| \
	(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) \| \
	(SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) \| \
	(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))

	#define ENET_NORMAL_PAD_CTRL \
	((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) \| \
	(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) \| \
	(SC_PAD_28FDSOI_DSE_18V_10MA << PADRING_DSE_SHIFT) \| \
	(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))

	#define UART_PAD_CTRL \
	((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) \| \
	(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) \| \
	(SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) \| \
	(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))

	static iomux_cfg_t uart2_pads[] = {
	SC_P_UART2_RX \| MUX_PAD_CTRL(UART_PAD_CTRL),
	SC_P_UART2_TX \| MUX_PAD_CTRL(UART_PAD_CTRL),
	};

	static void setup_iomux_uart(void)
	{
	imx8_iomux_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
	}

	int board_early_init_f(void)
	{
	/* Set UART clock root to 80 MHz */
	sc_pm_clock_rate_t rate = SC_80MHZ;
	int ret;

	ret = sc_pm_setup_uart(SC_R_UART_0, rate);
	ret \|= sc_pm_setup_uart(SC_R_UART_2, rate);
	if (ret)
	return ret;

	setup_iomux_uart();

	return 0;
	}

	#define ENET_PHY_RESET IMX_GPIO_NR(0, 3)
	#define ENET_TEST_1 IMX_GPIO_NR(0, 8)
	#define ENET_TEST_2 IMX_GPIO_NR(0, 9)

	/#define ETH_IO_TEST/
	static iomux_cfg_t enet_reset[] = {
	SC_P_ESAI0_SCKT \| MUX_MODE_ALT(4) \| MUX_PAD_CTRL(GPIO_PAD_CTRL),
	#ifdef ETH_IO_TEST
	/* GPIO0.IO08 MODE3: TXD0 */
	SC_P_ESAI0_TX4_RX1 \| MUX_MODE_ALT(4) \|
	MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL),
	/* GPIO0.IO09 MODE3: TXD1 */
	SC_P_ESAI0_TX5_RX0 \| MUX_MODE_ALT(4) \|
	MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL),
	#endif
	};

	static void enet_device_phy_reset(void)
	{
	int ret = 0;

	imx8_iomux_setup_multiple_pads(enet_reset, ARRAY_SIZE(enet_reset));

	ret = gpio_request(ENET_PHY_RESET, "enet_phy_reset");
	if (!ret) {
	gpio_direction_output(ENET_PHY_RESET, 1);
	gpio_set_value(ENET_PHY_RESET, 0);
	/* SMSC9303 TRM chapter 14.5.2 */
	udelay(200);
	gpio_set_value(ENET_PHY_RESET, 1);
	} else {
	printf("ENET RESET failed!\n");
	}

	#ifdef ETH_IO_TEST
	ret = gpio_request(ENET_TEST_1, "enet_test1");
	if (!ret) {
	int i;

	printf("ENET TEST 1!\n");
	for (i = 0; i < 20; i++) {
	gpio_direction_output(ENET_TEST_1, 1);
	gpio_set_value(ENET_TEST_1, 0);
	udelay(50);
	gpio_set_value(ENET_TEST_1, 1);
	udelay(50);
	}
	gpio_free(ENET_TEST_1);
	} else {
	printf("GPIO for ENET TEST 1 failed!\n");
	}
	ret = gpio_request(ENET_TEST_2, "enet_test2");
	if (!ret) {
	int i;

	printf("ENET TEST 2!\n");
	for (i = 0; i < 20; i++) {
	gpio_direction_output(ENET_TEST_2, 1);
	gpio_set_value(ENET_TEST_2, 0);
	udelay(50);
	gpio_set_value(ENET_TEST_2, 1);
	udelay(50);
	}
	gpio_free(ENET_TEST_2);
	} else {
	printf("GPIO for ENET TEST 2 failed!\n");
	}
	#endif
	}

	int setup_gpr_fec(void)
	{
	sc_ipc_t ipc_handle = -1;
	int err = 0;
	unsigned int test;

	/*
	* TX_CLK_SEL: it controls a mux between clock coming from the pad 50M
	* input pin and clock generated internally to connectivity subsystem
	* 0: internal clock
	* 1: external clock ---> your choice for RMII
	*
	* CLKDIV_SEL: it controls a div by 2 on the internal clock path à
	* it should be don’t care when using external clock
	* 0: non-divided clock
	* 1: clock divided by 2
	* 50_DISABLE or 125_DISABLE:
	* it’s used to disable the clock tree going outside the chip
	* when reference clock is generated internally.
	* It should be don’t care when reference clock is provided
	* externally.
	* 0: clock is enabled
	* 1: clock is disabled
	*
	* SC_C_TXCLK = 24,
	* SC_C_CLKDIV = 25,
	* SC_C_DISABLE_50 = 26,
	* SC_C_DISABLE_125 = 27,
	*/

	err = sc_misc_set_control(ipc_handle, SC_R_ENET_1, SC_C_TXCLK, 1);
	if (err)
	printf("Error in setting up SC_C %d\n\r", SC_C_TXCLK);

	sc_misc_get_control(ipc_handle, SC_R_ENET_1, SC_C_TXCLK, &test);
	debug("TEST SC_C %d-->%d\n\r", SC_C_TXCLK, test);

	err = sc_misc_set_control(ipc_handle, SC_R_ENET_1, SC_C_CLKDIV, 0);
	if (err)
	printf("Error in setting up SC_C %d\n\r", SC_C_CLKDIV);

	sc_misc_get_control(ipc_handle, SC_R_ENET_1, SC_C_CLKDIV, &test);
	debug("TEST SC_C %d-->%d\n\r", SC_C_CLKDIV, test);

	err = sc_misc_set_control(ipc_handle, SC_R_ENET_1, SC_C_DISABLE_50, 0);
	if (err)
	printf("Error in setting up SC_C %d\n\r", SC_C_DISABLE_50);

	sc_misc_get_control(ipc_handle, SC_R_ENET_1, SC_C_TXCLK, &test);
	debug("TEST SC_C %d-->%d\n\r", SC_C_DISABLE_50, test);

	err = sc_misc_set_control(ipc_handle, SC_R_ENET_1, SC_C_DISABLE_125, 1);
	if (err)
	printf("Error in setting up SC_C %d\n\r", SC_C_DISABLE_125);

	sc_misc_get_control(ipc_handle, SC_R_ENET_1, SC_C_TXCLK, &test);
	debug("TEST SC_C %d-->%d\n\r", SC_C_DISABLE_125, test);

	err = sc_misc_set_control(ipc_handle, SC_R_ENET_1, SC_C_SEL_125, 1);
	if (err)
	printf("Error in setting up SC_C %d\n\r", SC_C_SEL_125);

	sc_misc_get_control(ipc_handle, SC_R_ENET_1, SC_C_SEL_125, &test);
	debug("TEST SC_C %d-->%d\n\r", SC_C_SEL_125, test);

	return 0;
	}

	#if IS_ENABLED(CONFIG_FEC_MXC)
	#include <miiphy.h>
	int board_phy_config(struct phy_device *phydev)
	{
	if (phydev->drv->config)
	phydev->drv->config(phydev);

	return 0;
	}

	#endif

	static int setup_fec(void)
	{
	setup_gpr_fec();
	/* Reset ENET PHY */
	enet_device_phy_reset();
	return 0;
	}

	void reset_cpu(void)
	{
	}

	#ifndef CONFIG_SPL_BUILD
	/* LED's */
	static int board_led_init(void)
	{
	struct udevice bus, dev;
	u8 pca_led[2] = { 0x00, 0x00 };
	int ret;

	/* enable all leds on PCA9552 */
	ret = uclass_get_device_by_seq(UCLASS_I2C, PCA9552_1_I2C_BUS, &bus);
	if (ret) {
	printf("ERROR: I2C get %d\n", ret);
	return ret;
	}

	ret = dm_i2c_probe(bus, PCA9552_1_I2C_ADDR, 0, &dev);
	if (ret) {
	printf("ERROR: PCA9552 probe failed\n");
	return ret;
	}

	ret = dm_i2c_write(dev, 0x16, pca_led, sizeof(pca_led));
	if (ret) {
	printf("ERROR: PCA9552 write failed\n");
	return ret;
	}

	mdelay(1);
	return ret;
	}
	#endif /* !CONFIG_SPL_BUILD */

	int checkboard(void)
	{
	puts("Board: Capricorn\n");

	/*
	* Running build_info() doesn't work with current SCFW blob.
	* Uncomment below call when new blob is available.
	*/
	/build_info();/

	print_bootinfo();
	return 0;
	}

	int board_init(void)
	{
	setup_fec();
	return 0;
	}

	#ifdef CONFIG_OF_BOARD_SETUP
	int ft_board_setup(void blob, struct bd_info bd)
	{
	return 0;
	}
	#endif

	int board_mmc_get_env_dev(int devno)
	{
	return devno;
	}

	static int check_mmc_autodetect(void)
	{
	char *autodetect_str = env_get("mmcautodetect");

	if (autodetect_str && (strcmp(autodetect_str, "yes") == 0))
	return 1;

	return 0;
	}

	/* This should be defined for each board */
	__weak int mmc_map_to_kernel_blk(int dev_no)
	{
	return dev_no;
	}

	void board_late_mmc_env_init(void)
	{
	char cmd[32];
	char mmcblk[32];
	u32 dev_no = mmc_get_env_dev();

	if (!check_mmc_autodetect())
	return;

	env_set_ulong("mmcdev", dev_no);

	/* Set mmcblk env */
	sprintf(mmcblk, "/dev/mmcblk%dp2 rootwait rw",
	mmc_map_to_kernel_blk(dev_no));
	env_set("mmcroot", mmcblk);

	sprintf(cmd, "mmc dev %d", dev_no);
	run_command(cmd, 0);
	}

	#ifndef CONFIG_SPL_BUILD
	int factoryset_read_eeprom(int i2c_addr);

	static int load_parameters_from_factoryset(void)
	{
	int ret;

	ret = factoryset_read_eeprom(EEPROM_I2C_ADDR);
	if (ret)
	return ret;

	return factoryset_env_set();
	}

	int board_late_init(void)
	{
	env_set("sec_boot", "no");
	#ifdef CONFIG_AHAB_BOOT
	env_set("sec_boot", "yes");
	#endif

	#ifdef CONFIG_ENV_IS_IN_MMC
	board_late_mmc_env_init();
	#endif
	/* Init LEDs */
	if (board_led_init())
	printf("I2C LED init failed\n");

	/* Set environment from factoryset */
	if (load_parameters_from_factoryset())
	printf("Loading factoryset parameters failed!\n");

	return 0;
	}

	/* Service button */
	#define MAX_PIN_NUMBER 128
	#define BOARD_DEFAULT_BUTTON_GPIO IMX_GPIO_NR(1, 31)

	unsigned char get_button_state(char * const envname, unsigned char def)
	{
	int button = 0;
	int gpio;
	char *ptr_env;

	/* If button is not found we take default */
	ptr_env = env_get(envname);
	if (!ptr_env) {
	printf("Using default: %u\n", def);
	gpio = def;
	} else {
	gpio = (unsigned char)simple_strtoul(ptr_env, NULL, 0);
	if (gpio > MAX_PIN_NUMBER)
	gpio = def;
	}

	gpio_request(gpio, "");
	gpio_direction_input(gpio);
	if (gpio_get_value(gpio))
	button = 1;
	else
	button = 0;

	gpio_free(gpio);

	return button;
	}

	/*
	* This command returns the status of the user button on
	* Input - none
	* Returns - 1 if button is held down
	* 0 if button is not held down
	*/
	static int
	do_userbutton(struct cmd_tbl cmdtp, int flag, int argc, char const argv[])
	{
	int button = 0;

	button = get_button_state("button_usr1", BOARD_DEFAULT_BUTTON_GPIO);

	if (argc > 1)
	printf("Button state: %u\n", button);

	return button;
	}

	U_BOOT_CMD(
	usrbutton, CONFIG_SYS_MAXARGS, 2, do_userbutton,
	"Return the status of user button",
	"[print]"
	);

	#define ERST IMX_GPIO_NR(0, 3)

	static int
	do_eth_reset(struct cmd_tbl cmdtp, int flag, int argc, char const argv[])
	{
	gpio_request(ERST, "ERST");
	gpio_direction_output(ERST, 0);
	udelay(200);
	gpio_set_value(ERST, 1);
	return 0;
	}

	U_BOOT_CMD(
	switch_rst, CONFIG_SYS_MAXARGS, 2, do_eth_reset,
	"Reset eth phy",
	"[print]"
	);
	#endif /* ! CONFIG_SPL_BUILD */