Armada100: Add SPI support for Marvell gplugD
This patch add SPI driver support for Marvell gplugD
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
diff --git a/arch/arm/include/asm/arch-armada100/armada100.h b/arch/arm/include/asm/arch-armada100/armada100.h
index c449d4e..a8181b6 100644
--- a/arch/arm/include/asm/arch-armada100/armada100.h
+++ b/arch/arm/include/asm/arch-armada100/armada100.h
@@ -45,6 +45,10 @@
#define FE_CLK_RST 0x1
#define FE_CLK_ENA 0x8
+/* SSP2 Clock Control */
+#define SSP2_APBCLK 0x01
+#define SSP2_FNCLK 0x02
+
/* Register Base Addresses */
#define ARMD1_DRAM_BASE 0xB0000000
#define ARMD1_FEC_BASE 0xC0800000
@@ -175,5 +179,20 @@
u32 ac97; /*0x084*/
};
+/*
+* APB2 Clock Reset/Control Registers
+* Refer Datasheet Appendix A.11
+*/
+struct armd1apb2_registers {
+ u32 pad1[0x01C - 0x000];
+ u32 ssp1_clkrst; /* 0x01C */
+ u32 ssp2_clkrst; /* 0x020 */
+ u32 pad2[0x04C - 0x020 - 4];
+ u32 ssp3_clkrst; /* 0x04C */
+ u32 pad3[0x058 - 0x04C - 4];
+ u32 ssp4_clkrst; /* 0x058 */
+ u32 ssp5_clkrst; /* 0x05C */
+};
+
#endif /* CONFIG_ARMADA100 */
#endif /* _ASM_ARCH_ARMADA100_H */
diff --git a/arch/arm/include/asm/arch-armada100/mfp.h b/arch/arm/include/asm/arch-armada100/mfp.h
index da76b58..d48251a 100644
--- a/arch/arm/include/asm/arch-armada100/mfp.h
+++ b/arch/arm/include/asm/arch-armada100/mfp.h
@@ -83,6 +83,12 @@
#define MFP101_ETH_MDIO (MFP_REG(0x194) | MFP_AF5 | MFP_DRIVE_MEDIUM)
#define MFP103_ETH_RXDV (MFP_REG(0x19C) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+/* SPI */
+#define MFP107_SSP2_RXD (MFP_REG(0x1AC) | MFP_AF4 | MFP_DRIVE_MEDIUM)
+#define MFP108_SSP2_TXD (MFP_REG(0x1B0) | MFP_AF4 | MFP_DRIVE_MEDIUM)
+#define MFP110_SSP2_CS (MFP_REG(0x1B8) | MFP_AF0 | MFP_DRIVE_MEDIUM)
+#define MFP111_SSP2_CLK (MFP_REG(0x1BC) | MFP_AF4 | MFP_DRIVE_MEDIUM)
+
/* More macros can be defined here... */
#define MFP_PIN_MAX 117
diff --git a/board/Marvell/gplugd/gplugd.c b/board/Marvell/gplugd/gplugd.c
index b4f7f81..42c8389 100644
--- a/board/Marvell/gplugd/gplugd.c
+++ b/board/Marvell/gplugd/gplugd.c
@@ -72,6 +72,12 @@
MFP101_ETH_MDIO,
MFP103_ETH_RXDV,
+ /* SSP2 */
+ MFP107_SSP2_RXD,
+ MFP108_SSP2_TXD,
+ MFP110_SSP2_CS,
+ MFP111_SSP2_CLK,
+
MFP_EOC /*End of configuration*/
};
/* configure MFP's */
@@ -81,6 +87,9 @@
int board_init(void)
{
+ struct armd1apb2_registers *apb2_regs =
+ (struct armd1apb2_registers *)ARMD1_APBC2_BASE;
+
/* arch number of Board */
gd->bd->bi_arch_number = MACH_TYPE_SHEEVAD;
/* adress of boot parameters */
@@ -90,6 +99,9 @@
udelay(10);
/* Deassert PHY_RST# */
gpio_set_value(CONFIG_SYS_GPIO_PHY_RST, GPIO_HIGH);
+
+ /* Enable SSP2 clock */
+ writel(SSP2_APBCLK | SSP2_FNCLK, &apb2_regs->ssp2_clkrst);
return 0;
}
diff --git a/include/configs/gplugd.h b/include/configs/gplugd.h
index a9f3b3b..6fa724a 100644
--- a/include/configs/gplugd.h
+++ b/include/configs/gplugd.h
@@ -90,6 +90,11 @@
/* GPIO Configuration for PHY */
#define CONFIG_SYS_GPIO_PHY_RST 104 /* GPIO104 */
+/* SPI Support */
+#define CONFIG_ARMADA100_SPI
+#define CONFIG_ENV_SPI_CS 110
+#define CONFIG_SYS_SSP_PORT 2
+
/*
* mv-common.h should be defined after CMD configs since it used them
* to enable certain macros