ARM: board: meson: rename odroid-c2 to p200
This renames the odroid-c2 to p200 and set it as the default GXBB board
Other boards (odroid-c2 and nanopi-k2) will inherit from p200
Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
diff --git a/board/amlogic/p200/MAINTAINERS b/board/amlogic/p200/MAINTAINERS
new file mode 100644
index 0000000..77a055b
--- /dev/null
+++ b/board/amlogic/p200/MAINTAINERS
@@ -0,0 +1,7 @@
+P200
+M: Beniamino Galvani <b.galvani@gmail.com>
+M: Neil Armstrong <narmstrong@baylibre.com>
+S: Maintained
+F: board/amlogic/p200/
+F: configs/nanopi-k2_defconfig
+F: configs/odroid-c2_defconfig
diff --git a/board/amlogic/p200/Makefile b/board/amlogic/p200/Makefile
new file mode 100644
index 0000000..f82a7ea
--- /dev/null
+++ b/board/amlogic/p200/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2016 Beniamino Galvani <b.galvani@gmail.com>
+
+obj-y := p200.o
diff --git a/board/amlogic/p200/README.nanopi-k2 b/board/amlogic/p200/README.nanopi-k2
new file mode 100644
index 0000000..d450d3c
--- /dev/null
+++ b/board/amlogic/p200/README.nanopi-k2
@@ -0,0 +1,99 @@
+U-Boot for NanoPi-K2
+====================
+
+NanoPi-K2 is a single board computer manufactured by FriendlyElec
+with the following specifications:
+
+ - Amlogic S905 ARM Cortex-A53 quad-core SoC @ 1.5GHz
+ - ARM Mali 450 GPU
+ - 2GB DDR3 SDRAM
+ - Gigabit Ethernet
+ - HDMI 2.0 4K/60Hz display
+ - 40-pin GPIO header
+ - 4 x USB 2.0 Host, 1 x USB OTG
+ - eMMC, microSD
+ - Infrared receiver
+
+Schematics are available on the manufacturer website.
+
+Currently the u-boot port supports the following devices:
+ - serial
+ - eMMC, microSD
+ - Ethernet
+
+u-boot compilation
+==================
+
+ > export ARCH=arm
+ > export CROSS_COMPILE=aarch64-none-elf-
+ > make nanopi-k2_defconfig
+ > make
+
+Image creation
+==============
+
+Amlogic doesn't provide sources for the firmware and for tools needed
+to create the bootloader image, so it is necessary to obtain them from
+the git tree published by the board vendor:
+
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
+ > git clone https://github.com/BayLibre/u-boot.git -b libretech-cc amlogic-u-boot
+ > git clone https://github.com/friendlyarm/u-boot.git -b nanopi-k2-v2015.01 amlogic-u-boot
+ > cd amlogic-u-boot
+ > sed -i 's/aarch64-linux-gnu-/aarch64-none-elf-/' Makefile
+ > sed -i 's/arm-linux-/arm-none-eabi-/' arch/arm/cpu/armv8/gxb/firmware/scp_task/Makefile
+ > make nanopi-k2_defconfig
+ > make
+ > export FIPDIR=$PWD/fip
+
+Go back to mainline U-Boot source tree then :
+ > mkdir fip
+
+ > cp $FIPDIR/gxb/bl2.bin fip/
+ > cp $FIPDIR/gxb/acs.bin fip/
+ > cp $FIPDIR/gxb/bl21.bin fip/
+ > cp $FIPDIR/gxb/bl30.bin fip/
+ > cp $FIPDIR/gxb/bl301.bin fip/
+ > cp $FIPDIR/gxb/bl31.img fip/
+ > cp u-boot.bin fip/bl33.bin
+
+ > $FIPDIR/blx_fix.sh \
+ fip/bl30.bin \
+ fip/zero_tmp \
+ fip/bl30_zero.bin \
+ fip/bl301.bin \
+ fip/bl301_zero.bin \
+ fip/bl30_new.bin \
+ bl30
+
+ > $FIPDIR/fip_create \
+ --bl30 fip/bl30_new.bin \
+ --bl31 fip/bl31.img \
+ --bl33 fip/bl33.bin \
+ fip/fip.bin
+
+ > python $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0
+
+ > $FIPDIR/blx_fix.sh \
+ fip/bl2_acs.bin \
+ fip/zero_tmp \
+ fip/bl2_zero.bin \
+ fip/bl21.bin \
+ fip/bl21_zero.bin \
+ fip/bl2_new.bin \
+ bl2
+
+ > cat fip/bl2_new.bin fip/fip.bin > fip/boot_new.bin
+
+ > $FIPDIR/gxb/aml_encrypt_gxb --bootsig \
+ --input fip/boot_new.bin
+ --output fip/u-boot.bin
+
+and then write the image to SD with:
+
+ > DEV=/dev/your_sd_device
+ > dd if=fip/u-boot.bin of=$DEV conv=fsync,notrunc bs=512 seek=1
diff --git a/board/amlogic/p200/README.odroid-c2 b/board/amlogic/p200/README.odroid-c2
new file mode 100644
index 0000000..bed48c5
--- /dev/null
+++ b/board/amlogic/p200/README.odroid-c2
@@ -0,0 +1,66 @@
+U-Boot for ODROID-C2
+====================
+
+ODROID-C2 is a single board computer manufactured by Hardkernel
+Co. Ltd with the following specifications:
+
+ - Amlogic S905 ARM Cortex-A53 quad-core SoC @ 2GHz
+ - ARM Mali 450 GPU
+ - 2GB DDR3 SDRAM
+ - Gigabit Ethernet
+ - HDMI 2.0 4K/60Hz display
+ - 40-pin GPIO header
+ - 4 x USB 2.0 Host, 1 x USB OTG
+ - eMMC, microSD
+ - Infrared receiver
+
+Schematics are available on the manufacturer website.
+
+Currently the u-boot port supports the following devices:
+ - serial
+ - eMMC, microSD
+ - Ethernet
+ - I2C
+ - Regulators
+ - Reset controller
+ - Clock controller
+ - ADC
+
+u-boot compilation
+==================
+
+ > export ARCH=arm
+ > export CROSS_COMPILE=aarch64-none-elf-
+ > make odroid-c2_defconfig
+ > make
+
+Image creation
+==============
+
+Amlogic doesn't provide sources for the firmware and for tools needed
+to create the bootloader image, so it is necessary to obtain them from
+the git tree published by the board vendor:
+
+ > DIR=odroid-c2
+ > git clone --depth 1 \
+ https://github.com/hardkernel/u-boot.git -b odroidc2-v2015.01 \
+ $DIR
+ > $DIR/fip/fip_create --bl30 $DIR/fip/gxb/bl30.bin \
+ --bl301 $DIR/fip/gxb/bl301.bin \
+ --bl31 $DIR/fip/gxb/bl31.bin \
+ --bl33 u-boot.bin \
+ $DIR/fip.bin
+ > $DIR/fip/fip_create --dump $DIR/fip.bin
+ > cat $DIR/fip/gxb/bl2.package $DIR/fip.bin > $DIR/boot_new.bin
+ > $DIR/fip/gxb/aml_encrypt_gxb --bootsig \
+ --input $DIR/boot_new.bin \
+ --output $DIR/u-boot.img
+ > dd if=$DIR/u-boot.img of=$DIR/u-boot.gxbb bs=512 skip=96
+
+and then write the image to SD with:
+
+ > DEV=/dev/your_sd_device
+ > BL1=$DIR/sd_fuse/bl1.bin.hardkernel
+ > dd if=$BL1 of=$DEV conv=fsync bs=1 count=442
+ > dd if=$BL1 of=$DEV conv=fsync bs=512 skip=1 seek=1
+ > dd if=$DIR/u-boot.gxbb of=$DEV conv=fsync bs=512 seek=97
diff --git a/board/amlogic/p200/p200.c b/board/amlogic/p200/p200.c
new file mode 100644
index 0000000..62f0f4c
--- /dev/null
+++ b/board/amlogic/p200/p200.c
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2016 Beniamino Galvani <b.galvani@gmail.com>
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <environment.h>
+#include <asm/io.h>
+#include <asm/arch/gx.h>
+#include <asm/arch/sm.h>
+#include <asm/arch/eth.h>
+#include <asm/arch/mem.h>
+
+#define EFUSE_SN_OFFSET 20
+#define EFUSE_SN_SIZE 16
+#define EFUSE_MAC_OFFSET 52
+#define EFUSE_MAC_SIZE 6
+
+int misc_init_r(void)
+{
+ u8 mac_addr[EFUSE_MAC_SIZE];
+ char serial[EFUSE_SN_SIZE];
+ ssize_t len;
+
+ meson_eth_init(PHY_INTERFACE_MODE_RGMII, 0);
+
+ if (!eth_env_get_enetaddr("ethaddr", mac_addr)) {
+ len = meson_sm_read_efuse(EFUSE_MAC_OFFSET,
+ mac_addr, EFUSE_MAC_SIZE);
+ if (len == EFUSE_MAC_SIZE && is_valid_ethaddr(mac_addr))
+ eth_env_set_enetaddr("ethaddr", mac_addr);
+ }
+
+ if (!env_get("serial#")) {
+ len = meson_sm_read_efuse(EFUSE_SN_OFFSET, serial,
+ EFUSE_SN_SIZE);
+ if (len == EFUSE_SN_SIZE)
+ env_set("serial#", serial);
+ }
+
+ return 0;
+}