| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright 2017~2020 NXP |
| * |
| */ |
| |
| #include <config.h> |
| #include <asm/global_data.h> |
| #include <asm/io.h> |
| #include <asm/arch/clock.h> |
| #include <asm/arch/sys_proto.h> |
| #include <dm.h> |
| #include <dm/device_compat.h> |
| #include <dm/device-internal.h> |
| #include <dm/device.h> |
| #include <errno.h> |
| #include <fuse.h> |
| #include <linux/delay.h> |
| #include <malloc.h> |
| #include <thermal.h> |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| #define SITES_MAX 16 |
| #define FLAGS_VER2 0x1 |
| #define FLAGS_VER3 0x2 |
| #define FLAGS_VER4 0x4 |
| |
| #define TMR_DISABLE 0x0 |
| #define TMR_ME 0x80000000 |
| #define TMR_ALPF 0x0c000000 |
| #define TMTMIR_DEFAULT 0x00000002 |
| #define TIER_DISABLE 0x0 |
| |
| #define TER_EN 0x80000000 |
| #define TER_ADC_PD 0x40000000 |
| #define TER_ALPF 0x3 |
| |
| #define IMX_TMU_POLLING_DELAY_MS 5000 |
| /* |
| * i.MX TMU Registers |
| */ |
| struct imx_tmu_site_regs { |
| u32 tritsr; /* Immediate Temperature Site Register */ |
| u32 tratsr; /* Average Temperature Site Register */ |
| u8 res0[0x8]; |
| }; |
| |
| struct imx_tmu_regs { |
| u32 tmr; /* Mode Register */ |
| u32 tsr; /* Status Register */ |
| u32 tmtmir; /* Temperature measurement interval Register */ |
| u8 res0[0x14]; |
| u32 tier; /* Interrupt Enable Register */ |
| u32 tidr; /* Interrupt Detect Register */ |
| u32 tiscr; /* Interrupt Site Capture Register */ |
| u32 ticscr; /* Interrupt Critical Site Capture Register */ |
| u8 res1[0x10]; |
| u32 tmhtcrh; /* High Temperature Capture Register */ |
| u32 tmhtcrl; /* Low Temperature Capture Register */ |
| u8 res2[0x8]; |
| u32 tmhtitr; /* High Temperature Immediate Threshold */ |
| u32 tmhtatr; /* High Temperature Average Threshold */ |
| u32 tmhtactr; /* High Temperature Average Crit Threshold */ |
| u8 res3[0x24]; |
| u32 ttcfgr; /* Temperature Configuration Register */ |
| u32 tscfgr; /* Sensor Configuration Register */ |
| u8 res4[0x78]; |
| struct imx_tmu_site_regs site[SITES_MAX]; |
| u8 res5[0x9f8]; |
| u32 ipbrr0; /* IP Block Revision Register 0 */ |
| u32 ipbrr1; /* IP Block Revision Register 1 */ |
| u8 res6[0x310]; |
| u32 ttr0cr; /* Temperature Range 0 Control Register */ |
| u32 ttr1cr; /* Temperature Range 1 Control Register */ |
| u32 ttr2cr; /* Temperature Range 2 Control Register */ |
| u32 ttr3cr; /* Temperature Range 3 Control Register */ |
| }; |
| |
| struct imx_tmu_regs_v4 { |
| u32 tmr; /* Mode Register */ |
| u32 tsr; /* Status Register */ |
| u32 tmsr; /* Monitor Site Register */ |
| u32 tmtmir; /* Temperature measurement interval Register */ |
| u8 res0[0x10]; |
| u32 tier; /* Interrupt Enable Register */ |
| u32 tidr; /* Interrupt Detect Register */ |
| u8 res1[0x8]; |
| u32 tiiscr; /* Interrupt Immediate Site Capture Register */ |
| u32 tiascr; /* Interrupt Average Site Capture Register */ |
| u32 ticscr; /* Interrupt Critical Site Capture Register */ |
| u8 res2[0x4]; |
| u32 tmhtcr; /* Monitor High Temperature Capture Register */ |
| u32 tmltcr; /* MonitorLow Temperature Capture Register */ |
| u32 tmrtrcr; /* Monitor Rising Temperature Rate Capture Register */ |
| u32 tmftrcr; /* Monitor Falling Temperature Rate Capture Register */ |
| u32 tmhtitr; /* Monitor High Temperature Immediate Threshold */ |
| u32 tmhtatr; /* Monitor High Temperature Average Threshold */ |
| u32 tmhtactr; /* Monitor High Temperature Average Crit Threshold */ |
| u8 res3[0x4]; |
| u32 tmltitr; /* Monitor Low Temperature Immediate Threshold */ |
| u32 tmltatr; /* Monitor Low Temperature Average Threshold */ |
| u32 tmltactr; /* Monitor Low Temperature Average Crit Threshold */ |
| u8 res4[0x4]; |
| u32 tmrtrctr; /* Monitor Rising Temperature Rate Critical Threshold Register */ |
| u32 tmftrctr; /* Monitor Falling Temperature Rate Critical Threshold Register */ |
| u8 res5[0x8]; |
| u32 ttcfgr; /* Temperature Configuration Register */ |
| u32 tscfgr; /* Sensor Configuration Register */ |
| u8 res6[0x78]; |
| u32 tritsr0; /* Immediate Temperature Site Register */ |
| u32 tratsr0; /* Average Temperature Site Register */ |
| u8 res7[0xdf8]; |
| u32 tcmcfg; /* Central Module Configuration */ |
| u8 res8[0xc]; |
| u32 ttrcr[16]; /* Temperature Range Control Register */ |
| }; |
| |
| struct imx_tmu_regs_v2 { |
| u32 ter; /* TMU enable Register */ |
| u32 tsr; /* Status Register */ |
| u32 tier; /* Interrupt enable register */ |
| u32 tidr; /* Interrupt detect register */ |
| u32 tmhtitr; /* Monitor high temperature immediate threshold register */ |
| u32 tmhtatr; /* Monitor high temperature average threshold register */ |
| u32 tmhtactr; /* TMU monitor high temperature average critical threshold register */ |
| u32 tscr; /* Sensor value capture register */ |
| u32 tritsr; /* Report immediate temperature site register 0 */ |
| u32 tratsr; /* Report average temperature site register 0 */ |
| u32 tasr; /* Amplifier setting register */ |
| u32 ttmc; /* Test MUX control */ |
| u32 tcaliv; |
| }; |
| |
| struct imx_tmu_regs_v3 { |
| u32 ter; /* TMU enable Register */ |
| u32 tps; /* Status Register */ |
| u32 tier; /* Interrupt enable register */ |
| u32 tidr; /* Interrupt detect register */ |
| u32 tmhtitr; /* Monitor high temperature immediate threshold register */ |
| u32 tmhtatr; /* Monitor high temperature average threshold register */ |
| u32 tmhtactr; /* TMU monitor high temperature average critical threshold register */ |
| u32 tscr; /* Sensor value capture register */ |
| u32 tritsr; /* Report immediate temperature site register 0 */ |
| u32 tratsr; /* Report average temperature site register 0 */ |
| u32 tasr; /* Amplifier setting register */ |
| u32 ttmc; /* Test MUX control */ |
| u32 tcaliv0; |
| u32 tcaliv1; |
| u32 tcaliv_m40; |
| u32 trim; |
| }; |
| |
| union tmu_regs { |
| struct imx_tmu_regs regs_v1; |
| struct imx_tmu_regs_v2 regs_v2; |
| struct imx_tmu_regs_v3 regs_v3; |
| struct imx_tmu_regs_v4 regs_v4; |
| }; |
| |
| struct imx_tmu_plat { |
| int critical; |
| int alert; |
| int polling_delay; |
| int id; |
| bool zone_node; |
| union tmu_regs *regs; |
| }; |
| |
| static int read_temperature(struct udevice *dev, int *temp) |
| { |
| struct imx_tmu_plat *pdata = dev_get_plat(dev); |
| ulong drv_data = dev_get_driver_data(dev); |
| u32 val; |
| u32 retry = 10; |
| u32 valid = 0; |
| |
| do { |
| mdelay(100); |
| retry--; |
| |
| if (drv_data & FLAGS_VER3) { |
| val = readl(&pdata->regs->regs_v3.tritsr); |
| valid = val & (1 << (30 + pdata->id)); |
| } else if (drv_data & FLAGS_VER2) { |
| val = readl(&pdata->regs->regs_v2.tritsr); |
| /* |
| * Check if TEMP is in valid range, the V bit in TRITSR |
| * only reflects the RAW uncalibrated data |
| */ |
| valid = ((val & 0xff) < 10 || (val & 0xff) > 125) ? 0 : 1; |
| } else if (drv_data & FLAGS_VER4) { |
| val = readl(&pdata->regs->regs_v4.tritsr0); |
| valid = val & 0x80000000; |
| } else { |
| val = readl(&pdata->regs->regs_v1.site[pdata->id].tritsr); |
| valid = val & 0x80000000; |
| } |
| } while (!valid && retry > 0); |
| |
| if (retry > 0) { |
| if (drv_data & FLAGS_VER3) { |
| val = (val >> (pdata->id * 16)) & 0xff; |
| if (val & 0x80) /* Negative */ |
| val = (~(val & 0x7f) + 1); |
| |
| *temp = val; |
| if (*temp < -40 || *temp > 125) /* Check the range */ |
| return -EINVAL; |
| |
| *temp *= 1000; |
| } else if (drv_data & FLAGS_VER4) { |
| *temp = (val & 0x1ff) * 1000; |
| if (val & 0x200) |
| *temp += 500; |
| |
| /* Convert Kelvin to Celsius */ |
| *temp -= 273000; |
| } else { |
| *temp = (val & 0xff) * 1000; |
| } |
| } else { |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| int imx_tmu_get_temp(struct udevice *dev, int *temp) |
| { |
| struct imx_tmu_plat *pdata = dev_get_plat(dev); |
| int cpu_tmp = 0; |
| int ret; |
| |
| ret = read_temperature(dev, &cpu_tmp); |
| if (ret) |
| return ret; |
| |
| while (cpu_tmp >= pdata->alert) { |
| dev_crit(dev, "CPU Temperature (%dC) is beyond alert (%dC), close to critical (%dC) waiting...\n", |
| cpu_tmp / 1000, pdata->alert / 1000, pdata->critical / 1000); |
| mdelay(pdata->polling_delay); |
| ret = read_temperature(dev, &cpu_tmp); |
| if (ret) |
| return ret; |
| } |
| |
| *temp = cpu_tmp / 1000; |
| |
| return 0; |
| } |
| |
| static const struct dm_thermal_ops imx_tmu_ops = { |
| .get_temp = imx_tmu_get_temp, |
| }; |
| |
| static int imx_tmu_calibration(struct udevice *dev) |
| { |
| int i, val, len, ret; |
| int index; |
| u32 range[4]; |
| const fdt32_t *calibration; |
| struct imx_tmu_plat *pdata = dev_get_plat(dev); |
| ulong drv_data = dev_get_driver_data(dev); |
| |
| dev_dbg(dev, "%s\n", __func__); |
| |
| if (drv_data & (FLAGS_VER2 | FLAGS_VER3)) |
| return 0; |
| |
| if (drv_data & FLAGS_VER4) { |
| calibration = dev_read_prop(dev, "fsl,tmu-calibration", &len); |
| if (!calibration || len % 8 || len > 128) { |
| printf("TMU: invalid calibration data.\n"); |
| return -ENODEV; |
| } |
| |
| for (i = 0; i < len; i += 8, calibration += 2) { |
| index = i / 8; |
| writel(index, &pdata->regs->regs_v4.ttcfgr); |
| val = fdt32_to_cpu(*calibration); |
| writel(val, &pdata->regs->regs_v4.tscfgr); |
| val = fdt32_to_cpu(*(calibration + 1)); |
| writel((1 << 31) | val, &pdata->regs->regs_v4.ttrcr[index]); |
| } |
| |
| return 0; |
| } |
| |
| ret = dev_read_u32_array(dev, "fsl,tmu-range", range, 4); |
| if (ret) { |
| dev_err(dev, "TMU: missing calibration range, ret = %d.\n", ret); |
| return ret; |
| } |
| |
| /* Init temperature range registers */ |
| writel(range[0], &pdata->regs->regs_v1.ttr0cr); |
| writel(range[1], &pdata->regs->regs_v1.ttr1cr); |
| writel(range[2], &pdata->regs->regs_v1.ttr2cr); |
| writel(range[3], &pdata->regs->regs_v1.ttr3cr); |
| |
| calibration = dev_read_prop(dev, "fsl,tmu-calibration", &len); |
| if (!calibration || len % 8) { |
| dev_err(dev, "TMU: invalid calibration data.\n"); |
| return -ENODEV; |
| } |
| |
| for (i = 0; i < len; i += 8, calibration += 2) { |
| val = fdt32_to_cpu(*calibration); |
| writel(val, &pdata->regs->regs_v1.ttcfgr); |
| val = fdt32_to_cpu(*(calibration + 1)); |
| writel(val, &pdata->regs->regs_v1.tscfgr); |
| } |
| |
| return 0; |
| } |
| |
| #if defined(CONFIG_IMX8MM) || defined(CONFIG_IMX8MN) |
| static void imx_tmu_mx8mm_mx8mn_init(struct udevice *dev) |
| { |
| /* Load TCALIV and TASR from fuses */ |
| struct ocotp_regs *ocotp = |
| (struct ocotp_regs *)OCOTP_BASE_ADDR; |
| struct fuse_bank *bank = &ocotp->bank[3]; |
| struct fuse_bank3_regs *fuse = |
| (struct fuse_bank3_regs *)bank->fuse_regs; |
| struct imx_tmu_plat *pdata = dev_get_plat(dev); |
| void *reg_base = (void *)pdata->regs; |
| |
| u32 tca_rt, tca_hr, tca_en; |
| u32 buf_vref, buf_slope; |
| |
| tca_rt = fuse->ana0 & 0xFF; |
| tca_hr = (fuse->ana0 & 0xFF00) >> 8; |
| tca_en = (fuse->ana0 & 0x2000000) >> 25; |
| |
| buf_vref = (fuse->ana0 & 0x1F00000) >> 20; |
| buf_slope = (fuse->ana0 & 0xF0000) >> 16; |
| |
| writel(buf_vref | (buf_slope << 16), (ulong)reg_base + 0x28); |
| writel((tca_en << 31) | (tca_hr << 16) | tca_rt, |
| (ulong)reg_base + 0x30); |
| } |
| #else |
| static inline void imx_tmu_mx8mm_mx8mn_init(struct udevice *dev) { } |
| #endif |
| |
| #if defined(CONFIG_IMX8MP) |
| static void imx_tmu_mx8mp_init(struct udevice *dev) |
| { |
| /* Load TCALIV0/1/m40 and TRIM from fuses */ |
| struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR; |
| struct fuse_bank *bank = &ocotp->bank[38]; |
| struct fuse_bank38_regs *fuse = |
| (struct fuse_bank38_regs *)bank->fuse_regs; |
| struct fuse_bank *bank2 = &ocotp->bank[39]; |
| struct fuse_bank39_regs *fuse2 = |
| (struct fuse_bank39_regs *)bank2->fuse_regs; |
| struct imx_tmu_plat *pdata = dev_get_plat(dev); |
| void *reg_base = (void *)pdata->regs; |
| u32 buf_vref, buf_slope, bjt_cur, vlsb, bgr; |
| u32 reg; |
| u32 tca40[2], tca25[2], tca105[2]; |
| |
| /* For blank sample */ |
| if (!fuse->ana_trim2 && !fuse->ana_trim3 && |
| !fuse->ana_trim4 && !fuse2->ana_trim5) { |
| /* Use a default 25C binary codes */ |
| tca25[0] = 1596; |
| tca25[1] = 1596; |
| writel(tca25[0], (ulong)reg_base + 0x30); |
| writel(tca25[1], (ulong)reg_base + 0x34); |
| return; |
| } |
| |
| buf_vref = (fuse->ana_trim2 & 0xc0) >> 6; |
| buf_slope = (fuse->ana_trim2 & 0xF00) >> 8; |
| bjt_cur = (fuse->ana_trim2 & 0xF000) >> 12; |
| bgr = (fuse->ana_trim2 & 0xF0000) >> 16; |
| vlsb = (fuse->ana_trim2 & 0xF00000) >> 20; |
| writel(buf_vref | (buf_slope << 16), (ulong)reg_base + 0x28); |
| |
| reg = (bgr << 28) | (bjt_cur << 20) | (vlsb << 12) | (1 << 7); |
| writel(reg, (ulong)reg_base + 0x3c); |
| |
| tca40[0] = (fuse->ana_trim3 & 0xFFF0000) >> 16; |
| tca25[0] = (fuse->ana_trim3 & 0xF0000000) >> 28; |
| tca25[0] |= ((fuse->ana_trim4 & 0xFF) << 4); |
| tca105[0] = (fuse->ana_trim4 & 0xFFF00) >> 8; |
| tca40[1] = (fuse->ana_trim4 & 0xFFF00000) >> 20; |
| tca25[1] = fuse2->ana_trim5 & 0xFFF; |
| tca105[1] = (fuse2->ana_trim5 & 0xFFF000) >> 12; |
| |
| /* use 25c for 1p calibration */ |
| writel(tca25[0] | (tca105[0] << 16), (ulong)reg_base + 0x30); |
| writel(tca25[1] | (tca105[1] << 16), (ulong)reg_base + 0x34); |
| writel(tca40[0] | (tca40[1] << 16), (ulong)reg_base + 0x38); |
| } |
| #else |
| static inline void imx_tmu_mx8mp_init(struct udevice *dev) { } |
| #endif |
| |
| static inline void imx_tmu_mx93_init(struct udevice *dev) { } |
| static inline void imx_tmu_mx8mq_init(struct udevice *dev) { } |
| |
| static void imx_tmu_arch_init(struct udevice *dev) |
| { |
| if (is_imx8mm() || is_imx8mn()) |
| imx_tmu_mx8mm_mx8mn_init(dev); |
| else if (is_imx8mp()) |
| imx_tmu_mx8mp_init(dev); |
| else if (is_imx93()) |
| imx_tmu_mx93_init(dev); |
| else if (is_imx8mq()) |
| imx_tmu_mx8mq_init(dev); |
| else |
| dev_err(dev, "Unsupported SoC, TMU calibration not loaded!\n"); |
| } |
| |
| static void imx_tmu_init(struct udevice *dev) |
| { |
| struct imx_tmu_plat *pdata = dev_get_plat(dev); |
| ulong drv_data = dev_get_driver_data(dev); |
| |
| dev_dbg(dev, "%s\n", __func__); |
| |
| if (drv_data & FLAGS_VER3) { |
| /* Disable monitoring */ |
| writel(0x0, &pdata->regs->regs_v3.ter); |
| |
| /* Disable interrupt, using polling instead */ |
| writel(0x0, &pdata->regs->regs_v3.tier); |
| |
| } else if (drv_data & FLAGS_VER2) { |
| /* Disable monitoring */ |
| writel(0x0, &pdata->regs->regs_v2.ter); |
| |
| /* Disable interrupt, using polling instead */ |
| writel(0x0, &pdata->regs->regs_v2.tier); |
| } else if (drv_data & FLAGS_VER4) { |
| /* Disable monitoring */ |
| writel(TMR_DISABLE, &pdata->regs->regs_v4.tmr); |
| |
| /* Disable interrupt, using polling instead */ |
| writel(TIER_DISABLE, &pdata->regs->regs_v4.tier); |
| |
| /* Set update_interval */ |
| writel(TMTMIR_DEFAULT, &pdata->regs->regs_v4.tmtmir); |
| } else { |
| /* Disable monitoring */ |
| writel(TMR_DISABLE, &pdata->regs->regs_v1.tmr); |
| |
| /* Disable interrupt, using polling instead */ |
| writel(TIER_DISABLE, &pdata->regs->regs_v1.tier); |
| |
| /* Set update_interval */ |
| writel(TMTMIR_DEFAULT, &pdata->regs->regs_v1.tmtmir); |
| } |
| |
| imx_tmu_arch_init(dev); |
| } |
| |
| static int imx_tmu_enable_msite(struct udevice *dev) |
| { |
| struct imx_tmu_plat *pdata = dev_get_plat(dev); |
| ulong drv_data = dev_get_driver_data(dev); |
| u32 reg; |
| |
| dev_dbg(dev, "%s\n", __func__); |
| |
| if (!pdata->regs) |
| return -EIO; |
| |
| if (drv_data & FLAGS_VER3) { |
| reg = readl(&pdata->regs->regs_v3.ter); |
| reg &= ~TER_EN; |
| writel(reg, &pdata->regs->regs_v3.ter); |
| |
| writel(pdata->id << 30, &pdata->regs->regs_v3.tps); |
| |
| reg &= ~TER_ALPF; |
| reg |= 0x1; |
| reg &= ~TER_ADC_PD; |
| writel(reg, &pdata->regs->regs_v3.ter); |
| |
| /* Enable monitor */ |
| reg |= TER_EN; |
| writel(reg, &pdata->regs->regs_v3.ter); |
| } else if (drv_data & FLAGS_VER2) { |
| reg = readl(&pdata->regs->regs_v2.ter); |
| reg &= ~TER_EN; |
| writel(reg, &pdata->regs->regs_v2.ter); |
| |
| reg &= ~TER_ALPF; |
| reg |= 0x1; |
| writel(reg, &pdata->regs->regs_v2.ter); |
| |
| /* Enable monitor */ |
| reg |= TER_EN; |
| writel(reg, &pdata->regs->regs_v2.ter); |
| } else if (drv_data & FLAGS_VER4) { |
| reg = readl(&pdata->regs->regs_v4.tcmcfg); |
| reg |= (1 << 30) | (1 << 28); |
| reg &= ~0xF000; /* set SAR clk = IPG clk /16 */ |
| writel(reg, &pdata->regs->regs_v4.tcmcfg); |
| |
| /* Set ALPF*/ |
| reg = readl(&pdata->regs->regs_v4.tmr); |
| reg |= TMR_ALPF; |
| writel(reg, &pdata->regs->regs_v4.tmr); |
| |
| writel(1, &pdata->regs->regs_v4.tmsr); |
| |
| /* Enable ME */ |
| reg |= TMR_ME; |
| writel(reg, &pdata->regs->regs_v4.tmr); |
| } else { |
| /* Clear the ME before setting MSITE and ALPF*/ |
| reg = readl(&pdata->regs->regs_v1.tmr); |
| reg &= ~TMR_ME; |
| writel(reg, &pdata->regs->regs_v1.tmr); |
| |
| reg |= 1 << (15 - pdata->id); |
| reg |= TMR_ALPF; |
| writel(reg, &pdata->regs->regs_v1.tmr); |
| |
| /* Enable ME */ |
| reg |= TMR_ME; |
| writel(reg, &pdata->regs->regs_v1.tmr); |
| } |
| |
| return 0; |
| } |
| |
| static int imx_tmu_bind(struct udevice *dev) |
| { |
| struct imx_tmu_plat *pdata = dev_get_plat(dev); |
| int ret; |
| ofnode node, offset; |
| const char *name; |
| const void *prop; |
| int minc, maxc; |
| |
| dev_dbg(dev, "%s\n", __func__); |
| |
| prop = dev_read_prop(dev, "compatible", NULL); |
| if (!prop) |
| return 0; |
| |
| pdata->zone_node = 1; |
| /* default alert/crit temps based on temp grade */ |
| get_cpu_temp_grade(&minc, &maxc); |
| pdata->critical = maxc * 1000; |
| pdata->alert = (maxc - 10) * 1000; |
| |
| node = ofnode_path("/thermal-zones"); |
| ofnode_for_each_subnode(offset, node) { |
| /* Bind the subnode to this driver */ |
| name = ofnode_get_name(offset); |
| |
| ret = device_bind_with_driver_data(dev, dev->driver, name, |
| dev->driver_data, offset, |
| NULL); |
| if (ret) |
| dev_err(dev, "Error binding driver: %d\n", ret); |
| } |
| |
| return 0; |
| } |
| |
| static int imx_tmu_parse_fdt(struct udevice *dev) |
| { |
| struct imx_tmu_plat *pdata = dev_get_plat(dev), *p_parent_data; |
| struct ofnode_phandle_args args; |
| ofnode trips_np, cpu_thermal_np; |
| int ret; |
| |
| dev_dbg(dev, "%s\n", __func__); |
| |
| cpu_thermal_np = ofnode_path("/thermal-zones/cpu-thermal"); |
| pdata->polling_delay = ofnode_read_u32_default(cpu_thermal_np, "polling-delay", |
| IMX_TMU_POLLING_DELAY_MS); |
| |
| if (pdata->zone_node) { |
| pdata->regs = (union tmu_regs *)dev_read_addr_ptr(dev); |
| |
| if (!pdata->regs) |
| return -EINVAL; |
| return 0; |
| } |
| |
| p_parent_data = dev_get_plat(dev->parent); |
| if (p_parent_data->zone_node) |
| pdata->regs = p_parent_data->regs; |
| |
| ret = dev_read_phandle_with_args(dev, "thermal-sensors", |
| "#thermal-sensor-cells", |
| 0, 0, &args); |
| if (ret) |
| return ret; |
| |
| if (!ofnode_equal(args.node, dev_ofnode(dev->parent))) |
| return -EFAULT; |
| |
| if (args.args_count >= 1) |
| pdata->id = args.args[0]; |
| else |
| pdata->id = 0; |
| |
| dev_dbg(dev, "args.args_count %d, id %d\n", args.args_count, pdata->id); |
| |
| pdata->polling_delay = dev_read_u32_default(dev, "polling-delay", |
| IMX_TMU_POLLING_DELAY_MS); |
| |
| trips_np = ofnode_path("/thermal-zones/cpu-thermal/trips"); |
| ofnode_for_each_subnode(trips_np, trips_np) { |
| const char *type; |
| |
| type = ofnode_get_property(trips_np, "type", NULL); |
| if (!type) |
| continue; |
| if (!strcmp(type, "critical")) |
| pdata->critical = ofnode_read_u32_default(trips_np, "temperature", 85); |
| else if (strcmp(type, "passive") == 0) |
| pdata->alert = ofnode_read_u32_default(trips_np, "temperature", 80); |
| else |
| continue; |
| } |
| |
| dev_dbg(dev, "id %d polling_delay %d, critical %d, alert %d\n", |
| pdata->id, pdata->polling_delay, pdata->critical, pdata->alert); |
| |
| return 0; |
| } |
| |
| static int imx_tmu_probe(struct udevice *dev) |
| { |
| struct imx_tmu_plat *pdata = dev_get_plat(dev); |
| int ret; |
| |
| ret = imx_tmu_parse_fdt(dev); |
| if (ret) { |
| dev_err(dev, "Error in parsing TMU FDT %d\n", ret); |
| return ret; |
| } |
| |
| if (pdata->zone_node) { |
| imx_tmu_init(dev); |
| imx_tmu_calibration(dev); |
| imx_tmu_enable_msite(dev); |
| } else { |
| imx_tmu_enable_msite(dev); |
| } |
| |
| return 0; |
| } |
| |
| static const struct udevice_id imx_tmu_ids[] = { |
| { .compatible = "fsl,imx8mq-tmu", }, |
| { .compatible = "fsl,imx8mm-tmu", .data = FLAGS_VER2, }, |
| { .compatible = "fsl,imx8mp-tmu", .data = FLAGS_VER3, }, |
| { .compatible = "fsl,imx93-tmu", .data = FLAGS_VER4, }, |
| { } |
| }; |
| |
| U_BOOT_DRIVER(imx_tmu) = { |
| .name = "imx_tmu", |
| .id = UCLASS_THERMAL, |
| .ops = &imx_tmu_ops, |
| .of_match = imx_tmu_ids, |
| .bind = imx_tmu_bind, |
| .probe = imx_tmu_probe, |
| .plat_auto = sizeof(struct imx_tmu_plat), |
| .flags = DM_FLAG_PRE_RELOC, |
| }; |