| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright (C) 2016 Jagan Teki <jteki@openedev.com> |
| * Christophe Ricard <christophe.ricard@gmail.com> |
| * |
| * Copyright (C) 2010 Dirk Behme <dirk.behme@googlemail.com> |
| * |
| * Driver for McSPI controller on OMAP3. Based on davinci_spi.c |
| * Copyright (C) 2009 Texas Instruments Incorporated - https://www.ti.com/ |
| * |
| * Copyright (C) 2007 Atmel Corporation |
| * |
| * Parts taken from linux/drivers/spi/omap2_mcspi.c |
| * Copyright (C) 2005, 2006 Nokia Corporation |
| * |
| * Modified by Ruslan Araslanov <ruslan.araslanov@vitecmm.com> |
| */ |
| |
| #include <dm.h> |
| #include <spi.h> |
| #include <time.h> |
| #include <malloc.h> |
| #include <asm/global_data.h> |
| #include <asm/io.h> |
| #include <linux/bitops.h> |
| #include <omap3_spi.h> |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| struct omap2_mcspi_platform_config { |
| unsigned int regs_offset; |
| }; |
| |
| struct omap3_spi_priv { |
| struct mcspi *regs; |
| unsigned int cs; |
| unsigned int freq; |
| unsigned int mode; |
| unsigned int wordlen; |
| unsigned int pin_dir:1; |
| |
| bool bus_claimed; |
| }; |
| |
| static void omap3_spi_write_chconf(struct omap3_spi_priv *priv, int val) |
| { |
| writel(val, &priv->regs->channel[priv->cs].chconf); |
| /* Flash post writes to make immediate effect */ |
| readl(&priv->regs->channel[priv->cs].chconf); |
| } |
| |
| static void omap3_spi_set_enable(struct omap3_spi_priv *priv, int enable) |
| { |
| writel(enable, &priv->regs->channel[priv->cs].chctrl); |
| /* Flash post writes to make immediate effect */ |
| readl(&priv->regs->channel[priv->cs].chctrl); |
| } |
| |
| static int omap3_spi_write(struct omap3_spi_priv *priv, unsigned int len, |
| const void *txp, unsigned long flags) |
| { |
| ulong start; |
| int i, chconf; |
| |
| chconf = readl(&priv->regs->channel[priv->cs].chconf); |
| |
| /* Enable the channel */ |
| omap3_spi_set_enable(priv, OMAP3_MCSPI_CHCTRL_EN); |
| |
| chconf &= ~(OMAP3_MCSPI_CHCONF_TRM_MASK | OMAP3_MCSPI_CHCONF_WL_MASK); |
| chconf |= (priv->wordlen - 1) << 7; |
| chconf |= OMAP3_MCSPI_CHCONF_TRM_TX_ONLY; |
| chconf |= OMAP3_MCSPI_CHCONF_FORCE; |
| omap3_spi_write_chconf(priv, chconf); |
| |
| for (i = 0; i < len; i++) { |
| /* wait till TX register is empty (TXS == 1) */ |
| start = get_timer(0); |
| while (!(readl(&priv->regs->channel[priv->cs].chstat) & |
| OMAP3_MCSPI_CHSTAT_TXS)) { |
| if (get_timer(start) > SPI_WAIT_TIMEOUT) { |
| printf("SPI TXS timed out, status=0x%08x\n", |
| readl(&priv->regs->channel[priv->cs].chstat)); |
| return -1; |
| } |
| } |
| /* Write the data */ |
| unsigned int *tx = &priv->regs->channel[priv->cs].tx; |
| if (priv->wordlen > 16) |
| writel(((u32 *)txp)[i], tx); |
| else if (priv->wordlen > 8) |
| writel(((u16 *)txp)[i], tx); |
| else |
| writel(((u8 *)txp)[i], tx); |
| } |
| |
| /* wait to finish of transfer */ |
| while ((readl(&priv->regs->channel[priv->cs].chstat) & |
| (OMAP3_MCSPI_CHSTAT_EOT | OMAP3_MCSPI_CHSTAT_TXS)) != |
| (OMAP3_MCSPI_CHSTAT_EOT | OMAP3_MCSPI_CHSTAT_TXS)) |
| ; |
| |
| /* Disable the channel otherwise the next immediate RX will get affected */ |
| omap3_spi_set_enable(priv, OMAP3_MCSPI_CHCTRL_DIS); |
| |
| if (flags & SPI_XFER_END) { |
| |
| chconf &= ~OMAP3_MCSPI_CHCONF_FORCE; |
| omap3_spi_write_chconf(priv, chconf); |
| } |
| return 0; |
| } |
| |
| static int omap3_spi_read(struct omap3_spi_priv *priv, unsigned int len, |
| void *rxp, unsigned long flags) |
| { |
| int i, chconf; |
| ulong start; |
| |
| chconf = readl(&priv->regs->channel[priv->cs].chconf); |
| |
| /* Enable the channel */ |
| omap3_spi_set_enable(priv, OMAP3_MCSPI_CHCTRL_EN); |
| |
| chconf &= ~(OMAP3_MCSPI_CHCONF_TRM_MASK | OMAP3_MCSPI_CHCONF_WL_MASK); |
| chconf |= (priv->wordlen - 1) << 7; |
| chconf |= OMAP3_MCSPI_CHCONF_TRM_RX_ONLY; |
| chconf |= OMAP3_MCSPI_CHCONF_FORCE; |
| omap3_spi_write_chconf(priv, chconf); |
| |
| writel(0, &priv->regs->channel[priv->cs].tx); |
| |
| for (i = 0; i < len; i++) { |
| start = get_timer(0); |
| /* Wait till RX register contains data (RXS == 1) */ |
| while (!(readl(&priv->regs->channel[priv->cs].chstat) & |
| OMAP3_MCSPI_CHSTAT_RXS)) { |
| if (get_timer(start) > SPI_WAIT_TIMEOUT) { |
| printf("SPI RXS timed out, status=0x%08x\n", |
| readl(&priv->regs->channel[priv->cs].chstat)); |
| return -1; |
| } |
| } |
| |
| /* Disable the channel to prevent further receiving */ |
| if (i == (len - 1)) |
| omap3_spi_set_enable(priv, OMAP3_MCSPI_CHCTRL_DIS); |
| |
| /* Read the data */ |
| unsigned int *rx = &priv->regs->channel[priv->cs].rx; |
| if (priv->wordlen > 16) |
| ((u32 *)rxp)[i] = readl(rx); |
| else if (priv->wordlen > 8) |
| ((u16 *)rxp)[i] = (u16)readl(rx); |
| else |
| ((u8 *)rxp)[i] = (u8)readl(rx); |
| } |
| |
| if (flags & SPI_XFER_END) { |
| chconf &= ~OMAP3_MCSPI_CHCONF_FORCE; |
| omap3_spi_write_chconf(priv, chconf); |
| } |
| |
| return 0; |
| } |
| |
| /*McSPI Transmit Receive Mode*/ |
| static int omap3_spi_txrx(struct omap3_spi_priv *priv, unsigned int len, |
| const void *txp, void *rxp, unsigned long flags) |
| { |
| ulong start; |
| int chconf, i = 0; |
| |
| chconf = readl(&priv->regs->channel[priv->cs].chconf); |
| |
| /*Enable SPI channel*/ |
| omap3_spi_set_enable(priv, OMAP3_MCSPI_CHCTRL_EN); |
| |
| /*set TRANSMIT-RECEIVE Mode*/ |
| chconf &= ~(OMAP3_MCSPI_CHCONF_TRM_MASK | OMAP3_MCSPI_CHCONF_WL_MASK); |
| chconf |= (priv->wordlen - 1) << 7; |
| chconf |= OMAP3_MCSPI_CHCONF_FORCE; |
| omap3_spi_write_chconf(priv, chconf); |
| |
| /*Shift in and out 1 byte at time*/ |
| for (i=0; i < len; i++){ |
| /* Write: wait for TX empty (TXS == 1)*/ |
| start = get_timer(0); |
| while (!(readl(&priv->regs->channel[priv->cs].chstat) & |
| OMAP3_MCSPI_CHSTAT_TXS)) { |
| if (get_timer(start) > SPI_WAIT_TIMEOUT) { |
| printf("SPI TXS timed out, status=0x%08x\n", |
| readl(&priv->regs->channel[priv->cs].chstat)); |
| return -1; |
| } |
| } |
| /* Write the data */ |
| unsigned int *tx = &priv->regs->channel[priv->cs].tx; |
| if (priv->wordlen > 16) |
| writel(((u32 *)txp)[i], tx); |
| else if (priv->wordlen > 8) |
| writel(((u16 *)txp)[i], tx); |
| else |
| writel(((u8 *)txp)[i], tx); |
| |
| /*Read: wait for RX containing data (RXS == 1)*/ |
| start = get_timer(0); |
| while (!(readl(&priv->regs->channel[priv->cs].chstat) & |
| OMAP3_MCSPI_CHSTAT_RXS)) { |
| if (get_timer(start) > SPI_WAIT_TIMEOUT) { |
| printf("SPI RXS timed out, status=0x%08x\n", |
| readl(&priv->regs->channel[priv->cs].chstat)); |
| return -1; |
| } |
| } |
| /* Read the data */ |
| unsigned int *rx = &priv->regs->channel[priv->cs].rx; |
| if (priv->wordlen > 16) |
| ((u32 *)rxp)[i] = readl(rx); |
| else if (priv->wordlen > 8) |
| ((u16 *)rxp)[i] = (u16)readl(rx); |
| else |
| ((u8 *)rxp)[i] = (u8)readl(rx); |
| } |
| /* Disable the channel */ |
| omap3_spi_set_enable(priv, OMAP3_MCSPI_CHCTRL_DIS); |
| |
| /*if transfer must be terminated disable the channel*/ |
| if (flags & SPI_XFER_END) { |
| chconf &= ~OMAP3_MCSPI_CHCONF_FORCE; |
| omap3_spi_write_chconf(priv, chconf); |
| } |
| |
| return 0; |
| } |
| |
| static int _spi_xfer(struct omap3_spi_priv *priv, unsigned int bitlen, |
| const void *dout, void *din, unsigned long flags) |
| { |
| unsigned int len; |
| int ret = -1; |
| |
| if (priv->wordlen < 4 || priv->wordlen > 32) { |
| printf("omap3_spi: invalid wordlen %d\n", priv->wordlen); |
| return -1; |
| } |
| |
| if (bitlen % priv->wordlen) |
| return -1; |
| |
| len = bitlen / priv->wordlen; |
| |
| if (bitlen == 0) { /* only change CS */ |
| int chconf = readl(&priv->regs->channel[priv->cs].chconf); |
| |
| if (flags & SPI_XFER_BEGIN) { |
| omap3_spi_set_enable(priv, OMAP3_MCSPI_CHCTRL_EN); |
| chconf |= OMAP3_MCSPI_CHCONF_FORCE; |
| omap3_spi_write_chconf(priv, chconf); |
| } |
| if (flags & SPI_XFER_END) { |
| chconf &= ~OMAP3_MCSPI_CHCONF_FORCE; |
| omap3_spi_write_chconf(priv, chconf); |
| omap3_spi_set_enable(priv, OMAP3_MCSPI_CHCTRL_DIS); |
| } |
| ret = 0; |
| } else { |
| if (dout != NULL && din != NULL) |
| ret = omap3_spi_txrx(priv, len, dout, din, flags); |
| else if (dout != NULL) |
| ret = omap3_spi_write(priv, len, dout, flags); |
| else if (din != NULL) |
| ret = omap3_spi_read(priv, len, din, flags); |
| } |
| return ret; |
| } |
| |
| static void _omap3_spi_set_speed(struct omap3_spi_priv *priv) |
| { |
| uint32_t confr, div = 0; |
| |
| confr = readl(&priv->regs->channel[priv->cs].chconf); |
| |
| /* Calculate clock divisor. Valid range: 0x0 - 0xC ( /1 - /4096 ) */ |
| if (priv->freq) { |
| while (div <= 0xC && (OMAP3_MCSPI_MAX_FREQ / (1 << div)) |
| > priv->freq) |
| div++; |
| } else { |
| div = 0xC; |
| } |
| |
| /* set clock divisor */ |
| confr &= ~OMAP3_MCSPI_CHCONF_CLKD_MASK; |
| confr |= div << 2; |
| |
| omap3_spi_write_chconf(priv, confr); |
| } |
| |
| static void _omap3_spi_set_mode(struct omap3_spi_priv *priv) |
| { |
| uint32_t confr; |
| |
| confr = readl(&priv->regs->channel[priv->cs].chconf); |
| |
| /* standard 4-wire master mode: SCK, MOSI/out, MISO/in, nCS |
| * REVISIT: this controller could support SPI_3WIRE mode. |
| */ |
| if (priv->pin_dir == MCSPI_PINDIR_D0_IN_D1_OUT) { |
| confr &= ~(OMAP3_MCSPI_CHCONF_IS|OMAP3_MCSPI_CHCONF_DPE1); |
| confr |= OMAP3_MCSPI_CHCONF_DPE0; |
| } else { |
| confr &= ~OMAP3_MCSPI_CHCONF_DPE0; |
| confr |= OMAP3_MCSPI_CHCONF_IS|OMAP3_MCSPI_CHCONF_DPE1; |
| } |
| |
| /* set SPI mode 0..3 */ |
| confr &= ~(OMAP3_MCSPI_CHCONF_POL | OMAP3_MCSPI_CHCONF_PHA); |
| if (priv->mode & SPI_CPHA) |
| confr |= OMAP3_MCSPI_CHCONF_PHA; |
| if (priv->mode & SPI_CPOL) |
| confr |= OMAP3_MCSPI_CHCONF_POL; |
| |
| /* set chipselect polarity; manage with FORCE */ |
| if (!(priv->mode & SPI_CS_HIGH)) |
| confr |= OMAP3_MCSPI_CHCONF_EPOL; /* active-low; normal */ |
| else |
| confr &= ~OMAP3_MCSPI_CHCONF_EPOL; |
| |
| /* Transmit & receive mode */ |
| confr &= ~OMAP3_MCSPI_CHCONF_TRM_MASK; |
| |
| omap3_spi_write_chconf(priv, confr); |
| } |
| |
| static void _omap3_spi_set_wordlen(struct omap3_spi_priv *priv) |
| { |
| unsigned int confr; |
| |
| /* McSPI individual channel configuration */ |
| confr = readl(&priv->regs->channel[priv->cs].chconf); |
| |
| /* wordlength */ |
| confr &= ~OMAP3_MCSPI_CHCONF_WL_MASK; |
| confr |= (priv->wordlen - 1) << 7; |
| |
| omap3_spi_write_chconf(priv, confr); |
| } |
| |
| static void spi_reset(struct omap3_spi_priv *priv) |
| { |
| unsigned int tmp; |
| |
| writel(OMAP3_MCSPI_SYSCONFIG_SOFTRESET, &priv->regs->sysconfig); |
| do { |
| tmp = readl(&priv->regs->sysstatus); |
| } while (!(tmp & OMAP3_MCSPI_SYSSTATUS_RESETDONE)); |
| |
| writel(OMAP3_MCSPI_SYSCONFIG_AUTOIDLE | |
| OMAP3_MCSPI_SYSCONFIG_ENAWAKEUP | |
| OMAP3_MCSPI_SYSCONFIG_SMARTIDLE, &priv->regs->sysconfig); |
| |
| writel(OMAP3_MCSPI_WAKEUPENABLE_WKEN, &priv->regs->wakeupenable); |
| |
| /* |
| * Set the same default mode for each channel, especially CS polarity |
| * which must be common for all SPI slaves before any transfer. |
| */ |
| for (priv->cs = 0 ; priv->cs < OMAP4_MCSPI_CHAN_NB ; priv->cs++) |
| _omap3_spi_set_mode(priv); |
| priv->cs = 0; |
| } |
| |
| static void _omap3_spi_claim_bus(struct omap3_spi_priv *priv) |
| { |
| unsigned int conf; |
| /* |
| * setup when switching from (reset default) slave mode |
| * to single-channel master mode |
| */ |
| conf = readl(&priv->regs->modulctrl); |
| conf &= ~(OMAP3_MCSPI_MODULCTRL_STEST | OMAP3_MCSPI_MODULCTRL_MS); |
| conf |= OMAP3_MCSPI_MODULCTRL_SINGLE; |
| |
| writel(conf, &priv->regs->modulctrl); |
| |
| priv->bus_claimed = true; |
| } |
| |
| static int omap3_spi_claim_bus(struct udevice *dev) |
| { |
| struct udevice *bus = dev->parent; |
| struct omap3_spi_priv *priv = dev_get_priv(bus); |
| struct dm_spi_slave_plat *slave_plat = dev_get_parent_plat(dev); |
| |
| priv->cs = slave_plat->cs[0]; |
| if (!priv->freq) |
| priv->freq = slave_plat->max_hz; |
| |
| _omap3_spi_claim_bus(priv); |
| _omap3_spi_set_speed(priv); |
| _omap3_spi_set_mode(priv); |
| |
| return 0; |
| } |
| |
| static int omap3_spi_release_bus(struct udevice *dev) |
| { |
| struct udevice *bus = dev->parent; |
| struct omap3_spi_priv *priv = dev_get_priv(bus); |
| |
| writel(OMAP3_MCSPI_MODULCTRL_MS, &priv->regs->modulctrl); |
| |
| priv->bus_claimed = false; |
| |
| return 0; |
| } |
| |
| static int omap3_spi_set_wordlen(struct udevice *dev, unsigned int wordlen) |
| { |
| struct udevice *bus = dev->parent; |
| struct omap3_spi_priv *priv = dev_get_priv(bus); |
| struct dm_spi_slave_plat *slave_plat = dev_get_parent_plat(dev); |
| |
| priv->cs = slave_plat->cs[0]; |
| priv->wordlen = wordlen; |
| _omap3_spi_set_wordlen(priv); |
| |
| return 0; |
| } |
| |
| static int omap3_spi_probe(struct udevice *dev) |
| { |
| struct omap3_spi_priv *priv = dev_get_priv(dev); |
| struct omap3_spi_plat *plat = dev_get_plat(dev); |
| |
| priv->regs = plat->regs; |
| priv->pin_dir = plat->pin_dir; |
| priv->wordlen = SPI_DEFAULT_WORDLEN; |
| |
| spi_reset(priv); |
| |
| return 0; |
| } |
| |
| static int omap3_spi_xfer(struct udevice *dev, unsigned int bitlen, |
| const void *dout, void *din, unsigned long flags) |
| { |
| struct udevice *bus = dev->parent; |
| struct omap3_spi_priv *priv = dev_get_priv(bus); |
| |
| return _spi_xfer(priv, bitlen, dout, din, flags); |
| } |
| |
| static int omap3_spi_set_speed(struct udevice *dev, unsigned int speed) |
| { |
| |
| struct omap3_spi_priv *priv = dev_get_priv(dev); |
| |
| priv->freq = speed; |
| if (priv->bus_claimed) |
| _omap3_spi_set_speed(priv); |
| |
| return 0; |
| } |
| |
| static int omap3_spi_set_mode(struct udevice *dev, uint mode) |
| { |
| struct omap3_spi_priv *priv = dev_get_priv(dev); |
| |
| priv->mode = mode; |
| |
| if (priv->bus_claimed) |
| _omap3_spi_set_mode(priv); |
| |
| return 0; |
| } |
| |
| static const struct dm_spi_ops omap3_spi_ops = { |
| .claim_bus = omap3_spi_claim_bus, |
| .release_bus = omap3_spi_release_bus, |
| .set_wordlen = omap3_spi_set_wordlen, |
| .xfer = omap3_spi_xfer, |
| .set_speed = omap3_spi_set_speed, |
| .set_mode = omap3_spi_set_mode, |
| /* |
| * cs_info is not needed, since we require all chip selects to be |
| * in the device tree explicitly |
| */ |
| }; |
| |
| #if CONFIG_IS_ENABLED(OF_REAL) |
| static struct omap2_mcspi_platform_config omap2_pdata = { |
| .regs_offset = 0, |
| }; |
| |
| static struct omap2_mcspi_platform_config omap4_pdata = { |
| .regs_offset = OMAP4_MCSPI_REG_OFFSET, |
| }; |
| |
| static int omap3_spi_of_to_plat(struct udevice *dev) |
| { |
| struct omap2_mcspi_platform_config *data = |
| (struct omap2_mcspi_platform_config *)dev_get_driver_data(dev); |
| struct omap3_spi_plat *plat = dev_get_plat(dev); |
| |
| plat->regs = (struct mcspi *)(dev_read_addr(dev) + data->regs_offset); |
| |
| if (dev_read_bool(dev, "ti,pindir-d0-out-d1-in")) |
| plat->pin_dir = MCSPI_PINDIR_D0_OUT_D1_IN; |
| else |
| plat->pin_dir = MCSPI_PINDIR_D0_IN_D1_OUT; |
| |
| return 0; |
| } |
| |
| static const struct udevice_id omap3_spi_ids[] = { |
| { .compatible = "ti,omap2-mcspi", .data = (ulong)&omap2_pdata }, |
| { .compatible = "ti,omap4-mcspi", .data = (ulong)&omap4_pdata }, |
| { } |
| }; |
| #endif |
| U_BOOT_DRIVER(omap3_spi) = { |
| .name = "omap3_spi", |
| .id = UCLASS_SPI, |
| .flags = DM_FLAG_PRE_RELOC, |
| #if CONFIG_IS_ENABLED(OF_REAL) |
| .of_match = omap3_spi_ids, |
| .of_to_plat = omap3_spi_of_to_plat, |
| .plat_auto = sizeof(struct omap3_spi_plat), |
| #endif |
| .probe = omap3_spi_probe, |
| .ops = &omap3_spi_ops, |
| .priv_auto = sizeof(struct omap3_spi_priv), |
| }; |