Gitiles
Code Review Sign In
git01.mediatek.com / filogic / uboot / fb0889d356bd9f7ab75d7928eecba72bf7f0ce68 / . / drivers / mtd / cfi_flash.c
blob: e50502824aca257da700ef0eabbcee975a594fd8 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2002-2004
* Brad Kemp, Seranoa Networks, Brad.Kemp@seranoa.com
*
* Copyright (C) 2003 Arabella Software Ltd.
* Yuli Barcohen <yuli@arabellasw.com>
*
* Copyright (C) 2004
* Ed Okerson
*
* Copyright (C) 2006
* Tolunay Orkun <listmember@orkun.us>
*/
/* The DEBUG define must be before common to enable debugging */
/* #define DEBUG */
#include <config.h>
#include <console.h>
#include <dm.h>
#include <env.h>
#include <errno.h>
#include <fdt_support.h>
#include <flash.h>
#include <init.h>
#include <irq_func.h>
#include <log.h>
#include <time.h>
#include <asm/global_data.h>
#include <asm/processor.h>
#include <asm/io.h>
#include <asm/byteorder.h>
#include <asm/unaligned.h>
#include <env_internal.h>
#include <linux/delay.h>
#include <mtd/cfi_flash.h>
#include <watchdog.h>
/*
* This file implements a Common Flash Interface (CFI) driver for
* U-Boot.
*
* The width of the port and the width of the chips are determined at
* initialization. These widths are used to calculate the address for
* access CFI data structures.
*
* References
* JEDEC Standard JESD68 - Common Flash Interface (CFI)
* JEDEC Standard JEP137-A Common Flash Interface (CFI) ID Codes
* Intel Application Note 646 Common Flash Interface (CFI) and Command Sets
* Intel 290667-008 3 Volt Intel StrataFlash Memory datasheet
* AMD CFI Specification, Release 2.0 December 1, 2001
* AMD/Spansion Application Note: Migration from Single-byte to Three-byte
* Device IDs, Publication Number 25538 Revision A, November 8, 2001
*
* Define CFG_SYS_WRITE_SWAPPED_DATA, if you have to swap the Bytes between
* reading and writing ... (yes there is such a Hardware).
*/
DECLARE_GLOBAL_DATA_PTR;
static uint flash_offset_cfi[2] = { FLASH_OFFSET_CFI, FLASH_OFFSET_CFI_ALT };
#ifdef CONFIG_FLASH_CFI_MTD
static uint flash_verbose = 1;
#else
#define flash_verbose 1
#endif
flash_info_t flash_info[CFI_MAX_FLASH_BANKS]; /* FLASH chips info */
#ifdef CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
#define __maybe_weak __weak
#else
#define __maybe_weak static
#endif
/*
* 0xffff is an undefined value for the configuration register. When
* this value is returned, the configuration register shall not be
* written at all (default mode).
*/
static u16 cfi_flash_config_reg(int i)
{
#ifdef CONFIG_SYS_CFI_FLASH_CONFIG_REGS
return ((u16 [])CONFIG_SYS_CFI_FLASH_CONFIG_REGS)[i];
#else
return 0xffff;
#endif
}
#if defined(CONFIG_SYS_MAX_FLASH_BANKS_DETECT)
int cfi_flash_num_flash_banks = CFI_MAX_FLASH_BANKS;
#else
int cfi_flash_num_flash_banks;
#endif
#ifdef CONFIG_CFI_FLASH /* for driver model */
static void cfi_flash_init_dm(void)
{
struct udevice *dev;
cfi_flash_num_flash_banks = 0;
/*
* The uclass_first_device() will probe the first device and
* uclass_next_device() will probe the rest if they exist. So
* that cfi_flash_probe() will get called assigning the base
* addresses that are available.
*/
for (uclass_first_device(UCLASS_MTD, &dev);
dev;
uclass_next_device(&dev)) {
}
}
phys_addr_t cfi_flash_bank_addr(int i)
{
return flash_info[i].base;
}
#else
__weak phys_addr_t cfi_flash_bank_addr(int i)
{
return ((phys_addr_t [])CFG_SYS_FLASH_BANKS_LIST)[i];
}
#endif
__weak unsigned long cfi_flash_bank_size(int i)
{
#ifdef CFG_SYS_FLASH_BANKS_SIZES
return ((unsigned long [])CFG_SYS_FLASH_BANKS_SIZES)[i];
#else
return 0;
#endif
}
__maybe_weak void flash_write8(u8 value, void *addr)
{
__raw_writeb(value, addr);
}
__maybe_weak void flash_write16(u16 value, void *addr)
{
__raw_writew(value, addr);
}
__maybe_weak void flash_write32(u32 value, void *addr)
{
__raw_writel(value, addr);
}
__maybe_weak void flash_write64(u64 value, void *addr)
{
/* No architectures currently implement __raw_writeq() */
*(volatile u64 *)addr = value;
}
__maybe_weak u8 flash_read8(void *addr)
{
return __raw_readb(addr);
}
__maybe_weak u16 flash_read16(void *addr)
{
return __raw_readw(addr);
}
__maybe_weak u32 flash_read32(void *addr)
{
return __raw_readl(addr);
}
__maybe_weak u64 flash_read64(void *addr)
{
/* No architectures currently implement __raw_readq() */
return *(volatile u64 *)addr;
}
/*-----------------------------------------------------------------------
*/
#if defined(CONFIG_ENV_IS_IN_FLASH) || defined(CONFIG_ENV_ADDR_REDUND) || \
(defined(CONFIG_SYS_MONITOR_BASE) && \
(CONFIG_SYS_MONITOR_BASE >= CFG_SYS_FLASH_BASE))
static flash_info_t *flash_get_info(ulong base)
{
int i;
flash_info_t *info;
for (i = 0; i < CFI_FLASH_BANKS; i++) {
info = &flash_info[i];
if (info->size && info->start[0] <= base &&
base <= info->start[0] + info->size - 1)
return info;
}
return NULL;
}
#endif
unsigned long flash_sector_size(flash_info_t *info, flash_sect_t sect)
{
if (sect != (info->sector_count - 1))
return info->start[sect + 1] - info->start[sect];
else
return info->start[0] + info->size - info->start[sect];
}
/*-----------------------------------------------------------------------
* create an address based on the offset and the port width
*/
static inline void *
flash_map(flash_info_t *info, flash_sect_t sect, uint offset)
{
unsigned int byte_offset = offset * info->portwidth;
return (void *)(info->start[sect] + (byte_offset << info->chip_lsb));
}
static inline void flash_unmap(flash_info_t *info, flash_sect_t sect,
unsigned int offset, void *addr)
{
}
/*-----------------------------------------------------------------------
* make a proper sized command based on the port and chip widths
*/
static void flash_make_cmd(flash_info_t *info, u32 cmd, void *cmdbuf)
{
int i;
int cword_offset;
int cp_offset;
#if defined(__LITTLE_ENDIAN) || defined(CFG_SYS_WRITE_SWAPPED_DATA)
u32 cmd_le = cpu_to_le32(cmd);
#endif
uchar val;
uchar *cp = (uchar *) cmdbuf;
for (i = info->portwidth; i > 0; i--) {
cword_offset = (info->portwidth - i) % info->chipwidth;
#if defined(__LITTLE_ENDIAN) || defined(CFG_SYS_WRITE_SWAPPED_DATA)
cp_offset = info->portwidth - i;
val = *((uchar *)&cmd_le + cword_offset);
#else
cp_offset = i - 1;
val = *((uchar *)&cmd + sizeof(u32) - cword_offset - 1);
#endif
cp[cp_offset] = (cword_offset >= sizeof(u32)) ? 0x00 : val;
}
}
#ifdef DEBUG
/*-----------------------------------------------------------------------
* Debug support
*/
static void print_longlong(char *str, unsigned long long data)
{
int i;
char *cp;
cp = (char *)&data;
for (i = 0; i < 8; i++)
sprintf(&str[i * 2], "%2.2x", *cp++);
}
static void flash_printqry(struct cfi_qry *qry)
{
u8 *p = (u8 *)qry;
int x, y;
for (x = 0; x < sizeof(struct cfi_qry); x += 16) {
debug("%02x : ", x);
for (y = 0; y < 16; y++)
debug("%2.2x ", p[x + y]);
debug(" ");
for (y = 0; y < 16; y++) {
unsigned char c = p[x + y];
if (c >= 0x20 && c <= 0x7e)
debug("%c", c);
else
debug(".");
}
debug("\n");
}
}
#endif
/*-----------------------------------------------------------------------
* read a character at a port width address
*/
static inline uchar flash_read_uchar(flash_info_t *info, uint offset)
{
uchar *cp;
uchar retval;
cp = flash_map(info, 0, offset);
#if defined(__LITTLE_ENDIAN) || defined(CFG_SYS_WRITE_SWAPPED_DATA)
retval = flash_read8(cp);
#else
retval = flash_read8(cp + info->portwidth - 1);
#endif
flash_unmap(info, 0, offset, cp);
return retval;
}
/*-----------------------------------------------------------------------
* read a word at a port width address, assume 16bit bus
*/
static inline ushort flash_read_word(flash_info_t *info, uint offset)
{
ushort *addr, retval;
addr = flash_map(info, 0, offset);
retval = flash_read16(addr);
flash_unmap(info, 0, offset, addr);
return retval;
}
/*-----------------------------------------------------------------------
* read a long word by picking the least significant byte of each maximum
* port size word. Swap for ppc format.
*/
static ulong flash_read_long (flash_info_t *info, flash_sect_t sect,
uint offset)
{
uchar *addr;
ulong retval;
#ifdef DEBUG
int x;
#endif
addr = flash_map(info, sect, offset);
#ifdef DEBUG
debug("long addr is at %p info->portwidth = %d\n", addr,
info->portwidth);
for (x = 0; x < 4 * info->portwidth; x++)
debug("addr[%x] = 0x%x\n", x, flash_read8(addr + x));
#endif
#if defined(__LITTLE_ENDIAN) || defined(CFG_SYS_WRITE_SWAPPED_DATA)
retval = ((flash_read8(addr) << 16) |
(flash_read8(addr + info->portwidth) << 24) |
(flash_read8(addr + 2 * info->portwidth)) |
(flash_read8(addr + 3 * info->portwidth) << 8));
#else
retval = ((flash_read8(addr + 2 * info->portwidth - 1) << 24) |
(flash_read8(addr + info->portwidth - 1) << 16) |
(flash_read8(addr + 4 * info->portwidth - 1) << 8) |
(flash_read8(addr + 3 * info->portwidth - 1)));
#endif
flash_unmap(info, sect, offset, addr);
return retval;
}
/*
* Write a proper sized command to the correct address
*/
static void flash_write_cmd(flash_info_t *info, flash_sect_t sect,
uint offset, u32 cmd)
{
void *addr;
cfiword_t cword;
addr = flash_map(info, sect, offset);
flash_make_cmd(info, cmd, &cword);
switch (info->portwidth) {
case FLASH_CFI_8BIT:
debug("fwc addr %p cmd %x %x 8bit x %d bit\n", addr, cmd,
cword.w8, info->chipwidth << CFI_FLASH_SHIFT_WIDTH);
flash_write8(cword.w8, addr);
break;
case FLASH_CFI_16BIT:
debug("fwc addr %p cmd %x %4.4x 16bit x %d bit\n", addr,
cmd, cword.w16,
info->chipwidth << CFI_FLASH_SHIFT_WIDTH);
flash_write16(cword.w16, addr);
break;
case FLASH_CFI_32BIT:
debug("fwc addr %p cmd %x %8.8x 32bit x %d bit\n", addr,
cmd, cword.w32,
info->chipwidth << CFI_FLASH_SHIFT_WIDTH);
flash_write32(cword.w32, addr);
break;
case FLASH_CFI_64BIT:
#ifdef DEBUG
{
char str[20];
print_longlong(str, cword.w64);
debug("fwrite addr %p cmd %x %s 64 bit x %d bit\n",
addr, cmd, str,
info->chipwidth << CFI_FLASH_SHIFT_WIDTH);
}
#endif
flash_write64(cword.w64, addr);
break;
}
/* Ensure all the instructions are fully finished */
sync();
flash_unmap(info, sect, offset, addr);
}
static void flash_unlock_seq(flash_info_t *info, flash_sect_t sect)
{
flash_write_cmd(info, sect, info->addr_unlock1, AMD_CMD_UNLOCK_START);
flash_write_cmd(info, sect, info->addr_unlock2, AMD_CMD_UNLOCK_ACK);
}
/*-----------------------------------------------------------------------
*/
static int flash_isequal(flash_info_t *info, flash_sect_t sect, uint offset,
uchar cmd)
{
void *addr;
cfiword_t cword;
int retval;
addr = flash_map(info, sect, offset);
flash_make_cmd(info, cmd, &cword);
debug("is= cmd %x(%c) addr %p ", cmd, cmd, addr);
switch (info->portwidth) {
case FLASH_CFI_8BIT:
debug("is= %x %x\n", flash_read8(addr), cword.w8);
retval = (flash_read8(addr) == cword.w8);
break;
case FLASH_CFI_16BIT:
debug("is= %4.4x %4.4x\n", flash_read16(addr), cword.w16);
retval = (flash_read16(addr) == cword.w16);
break;
case FLASH_CFI_32BIT:
debug("is= %8.8x %8.8x\n", flash_read32(addr), cword.w32);
retval = (flash_read32(addr) == cword.w32);
break;
case FLASH_CFI_64BIT:
#ifdef DEBUG
{
char str1[20];
char str2[20];
print_longlong(str1, flash_read64(addr));
print_longlong(str2, cword.w64);
debug("is= %s %s\n", str1, str2);
}
#endif
retval = (flash_read64(addr) == cword.w64);
break;
default:
retval = 0;
break;
}
flash_unmap(info, sect, offset, addr);
return retval;
}
/*-----------------------------------------------------------------------
*/
static int flash_isset(flash_info_t *info, flash_sect_t sect, uint offset,
uchar cmd)
{
void *addr;
cfiword_t cword;
int retval;
addr = flash_map(info, sect, offset);
flash_make_cmd(info, cmd, &cword);
switch (info->portwidth) {
case FLASH_CFI_8BIT:
retval = ((flash_read8(addr) & cword.w8) == cword.w8);
break;
case FLASH_CFI_16BIT:
retval = ((flash_read16(addr) & cword.w16) == cword.w16);
break;
case FLASH_CFI_32BIT:
retval = ((flash_read32(addr) & cword.w32) == cword.w32);
break;
case FLASH_CFI_64BIT:
retval = ((flash_read64(addr) & cword.w64) == cword.w64);
break;
default:
retval = 0;
break;
}
flash_unmap(info, sect, offset, addr);
return retval;
}
/*-----------------------------------------------------------------------
*/
static int flash_toggle(flash_info_t *info, flash_sect_t sect, uint offset,
uchar cmd)
{
u8 *addr;
cfiword_t cword;
int retval;
addr = flash_map(info, sect, offset);
flash_make_cmd(info, cmd, &cword);
switch (info->portwidth) {
case FLASH_CFI_8BIT:
retval = flash_read8(addr) != flash_read8(addr);
break;
case FLASH_CFI_16BIT:
retval = flash_read16(addr) != flash_read16(addr);
break;
case FLASH_CFI_32BIT:
retval = flash_read32(addr) != flash_read32(addr);
break;
case FLASH_CFI_64BIT:
retval = ((flash_read32(addr) != flash_read32(addr)) ||
(flash_read32(addr + 4) != flash_read32(addr + 4)));
break;
default:
retval = 0;
break;
}
flash_unmap(info, sect, offset, addr);
return retval;
}
/*
* flash_is_busy - check to see if the flash is busy
*
* This routine checks the status of the chip and returns true if the
* chip is busy.
*/
static int flash_is_busy(flash_info_t *info, flash_sect_t sect)
{
int retval;
switch (info->vendor) {
case CFI_CMDSET_INTEL_PROG_REGIONS:
case CFI_CMDSET_INTEL_STANDARD:
case CFI_CMDSET_INTEL_EXTENDED:
retval = !flash_isset(info, sect, 0, FLASH_STATUS_DONE);
break;
case CFI_CMDSET_AMD_STANDARD:
case CFI_CMDSET_AMD_EXTENDED:
#ifdef CONFIG_FLASH_CFI_LEGACY
case CFI_CMDSET_AMD_LEGACY:
#endif
if (info->sr_supported) {
flash_write_cmd(info, sect, info->addr_unlock1,
FLASH_CMD_READ_STATUS);
retval = !flash_isset(info, sect, 0,
FLASH_STATUS_DONE);
} else {
retval = flash_toggle(info, sect, 0,
AMD_STATUS_TOGGLE);
}
break;
default:
retval = 0;
}
debug("%s: %d\n", __func__, retval);
return retval;
}
/*-----------------------------------------------------------------------
* wait for XSR.7 to be set. Time out with an error if it does not.
* This routine does not set the flash to read-array mode.
*/
static int flash_status_check(flash_info_t *info, flash_sect_t sector,
ulong tout, char *prompt)
{
ulong start;
#if CONFIG_SYS_HZ != 1000
/* Avoid overflow for large HZ */
if ((ulong)CONFIG_SYS_HZ > 100000)
tout *= (ulong)CONFIG_SYS_HZ / 1000;
else
tout = DIV_ROUND_UP(tout * (ulong)CONFIG_SYS_HZ, 1000);
#endif
/* Wait for command completion */
#ifdef CFG_SYS_LOW_RES_TIMER
reset_timer();
#endif
start = get_timer(0);
schedule();
while (flash_is_busy(info, sector)) {
if (get_timer(start) > tout) {
printf("Flash %s timeout at address %lx data %lx\n",
prompt, info->start[sector],
flash_read_long(info, sector, 0));
flash_write_cmd(info, sector, 0, info->cmd_reset);
udelay(1);
return FL_ERR_TIMEOUT;
}
udelay(1); /* also triggers watchdog */
}
return FL_ERR_OK;
}
/*-----------------------------------------------------------------------
* Wait for XSR.7 to be set, if it times out print an error, otherwise
* do a full status check.
*
* This routine sets the flash to read-array mode.
*/
static int flash_full_status_check(flash_info_t *info, flash_sect_t sector,
ulong tout, char *prompt)
{
int retcode;
retcode = flash_status_check(info, sector, tout, prompt);
switch (info->vendor) {
case CFI_CMDSET_INTEL_PROG_REGIONS:
case CFI_CMDSET_INTEL_EXTENDED:
case CFI_CMDSET_INTEL_STANDARD:
if (retcode == FL_ERR_OK &&
!flash_isset(info, sector, 0, FLASH_STATUS_DONE)) {
retcode = FL_ERR_INVAL;
printf("Flash %s error at address %lx\n", prompt,
info->start[sector]);
if (flash_isset(info, sector, 0, FLASH_STATUS_ECLBS |
FLASH_STATUS_PSLBS)) {
puts("Command Sequence Error.\n");
} else if (flash_isset(info, sector, 0,
FLASH_STATUS_ECLBS)) {
puts("Block Erase Error.\n");
retcode = FL_ERR_NOT_ERASED;
} else if (flash_isset(info, sector, 0,
FLASH_STATUS_PSLBS)) {
puts("Locking Error\n");
}
if (flash_isset(info, sector, 0, FLASH_STATUS_DPS)) {
puts("Block locked.\n");
retcode = FL_ERR_PROTECTED;
}
if (flash_isset(info, sector, 0, FLASH_STATUS_VPENS))
puts("Vpp Low Error.\n");
}
flash_write_cmd(info, sector, 0, info->cmd_reset);
udelay(1);
break;
default:
break;
}
return retcode;
}
static int use_flash_status_poll(flash_info_t *info)
{
#ifdef CONFIG_SYS_CFI_FLASH_STATUS_POLL
if (info->vendor == CFI_CMDSET_AMD_EXTENDED ||
info->vendor == CFI_CMDSET_AMD_STANDARD)
return 1;
#endif
return 0;
}
static int flash_status_poll(flash_info_t *info, void *src, void *dst,
ulong tout, char *prompt)
{
#ifdef CONFIG_SYS_CFI_FLASH_STATUS_POLL
ulong start;
int ready;
#if CONFIG_SYS_HZ != 1000
/* Avoid overflow for large HZ */
if ((ulong)CONFIG_SYS_HZ > 100000)
tout *= (ulong)CONFIG_SYS_HZ / 1000;
else
tout = DIV_ROUND_UP(tout * (ulong)CONFIG_SYS_HZ, 1000);
#endif
/* Wait for command completion */
#ifdef CFG_SYS_LOW_RES_TIMER
reset_timer();
#endif
start = get_timer(0);
schedule();
while (1) {
switch (info->portwidth) {
case FLASH_CFI_8BIT:
ready = flash_read8(dst) == flash_read8(src);
break;
case FLASH_CFI_16BIT:
ready = flash_read16(dst) == flash_read16(src);
break;
case FLASH_CFI_32BIT:
ready = flash_read32(dst) == flash_read32(src);
break;
case FLASH_CFI_64BIT:
ready = flash_read64(dst) == flash_read64(src);
break;
default:
ready = 0;
break;
}
if (ready)
break;
if (get_timer(start) > tout) {
printf("Flash %s timeout at address %lx data %lx\n",
prompt, (ulong)dst, (ulong)flash_read8(dst));
return FL_ERR_TIMEOUT;
}
udelay(1); /* also triggers watchdog */
}
#endif /* CONFIG_SYS_CFI_FLASH_STATUS_POLL */
return FL_ERR_OK;
}
/*-----------------------------------------------------------------------
*/
static void flash_add_byte(flash_info_t *info, cfiword_t *cword, uchar c)
{
#if defined(__LITTLE_ENDIAN) && !defined(CFG_SYS_WRITE_SWAPPED_DATA)
unsigned short w;
unsigned int l;
unsigned long long ll;
#endif
switch (info->portwidth) {
case FLASH_CFI_8BIT:
cword->w8 = c;
break;
case FLASH_CFI_16BIT:
#if defined(__LITTLE_ENDIAN) && !defined(CFG_SYS_WRITE_SWAPPED_DATA)
w = c;
w <<= 8;
cword->w16 = (cword->w16 >> 8) | w;
#else
cword->w16 = (cword->w16 << 8) | c;
#endif
break;
case FLASH_CFI_32BIT:
#if defined(__LITTLE_ENDIAN) && !defined(CFG_SYS_WRITE_SWAPPED_DATA)
l = c;
l <<= 24;
cword->w32 = (cword->w32 >> 8) | l;
#else
cword->w32 = (cword->w32 << 8) | c;
#endif
break;
case FLASH_CFI_64BIT:
#if defined(__LITTLE_ENDIAN) && !defined(CFG_SYS_WRITE_SWAPPED_DATA)
ll = c;
ll <<= 56;
cword->w64 = (cword->w64 >> 8) | ll;
#else
cword->w64 = (cword->w64 << 8) | c;
#endif
break;
}
}
/*
* Loop through the sector table starting from the previously found sector.
* Searches forwards or backwards, dependent on the passed address.
*/
static flash_sect_t find_sector(flash_info_t *info, ulong addr)
{
static flash_sect_t saved_sector; /* previously found sector */
static flash_info_t *saved_info; /* previously used flash bank */
flash_sect_t sector = saved_sector;
if (info != saved_info || sector >= info->sector_count)
sector = 0;
while ((sector < info->sector_count - 1) &&
(info->start[sector] < addr))
sector++;
while ((info->start[sector] > addr) && (sector > 0))
/*
* also decrements the sector in case of an overshot
* in the first loop
*/
sector--;
saved_sector = sector;
saved_info = info;
return sector;
}
/*-----------------------------------------------------------------------
*/
static int flash_write_cfiword(flash_info_t *info, ulong dest, cfiword_t cword)
{
void *dstaddr = (void *)dest;
int flag;
flash_sect_t sect = 0;
char sect_found = 0;
/* Check if Flash is (sufficiently) erased */
switch (info->portwidth) {
case FLASH_CFI_8BIT:
flag = ((flash_read8(dstaddr) & cword.w8) == cword.w8);
break;
case FLASH_CFI_16BIT:
flag = ((flash_read16(dstaddr) & cword.w16) == cword.w16);
break;
case FLASH_CFI_32BIT:
flag = ((flash_read32(dstaddr) & cword.w32) == cword.w32);
break;
case FLASH_CFI_64BIT:
flag = ((flash_read64(dstaddr) & cword.w64) == cword.w64);
break;
default:
flag = 0;
break;
}
if (!flag)
return FL_ERR_NOT_ERASED;
/* Disable interrupts which might cause a timeout here */
flag = disable_interrupts();
switch (info->vendor) {
case CFI_CMDSET_INTEL_PROG_REGIONS:
case CFI_CMDSET_INTEL_EXTENDED:
case CFI_CMDSET_INTEL_STANDARD:
flash_write_cmd(info, 0, 0, FLASH_CMD_CLEAR_STATUS);
flash_write_cmd(info, 0, 0, FLASH_CMD_WRITE);
break;
case CFI_CMDSET_AMD_EXTENDED:
case CFI_CMDSET_AMD_STANDARD:
sect = find_sector(info, dest);
flash_unlock_seq(info, sect);
flash_write_cmd(info, sect, info->addr_unlock1, AMD_CMD_WRITE);
sect_found = 1;
break;
#ifdef CONFIG_FLASH_CFI_LEGACY
case CFI_CMDSET_AMD_LEGACY:
sect = find_sector(info, dest);
flash_unlock_seq(info, 0);
flash_write_cmd(info, 0, info->addr_unlock1, AMD_CMD_WRITE);
sect_found = 1;
break;
#endif
}
switch (info->portwidth) {
case FLASH_CFI_8BIT:
flash_write8(cword.w8, dstaddr);
break;
case FLASH_CFI_16BIT:
flash_write16(cword.w16, dstaddr);
break;
case FLASH_CFI_32BIT:
flash_write32(cword.w32, dstaddr);
break;
case FLASH_CFI_64BIT:
flash_write64(cword.w64, dstaddr);
break;
}
/* re-enable interrupts if necessary */
if (flag)
enable_interrupts();
if (!sect_found)
sect = find_sector(info, dest);
if (use_flash_status_poll(info))
return flash_status_poll(info, &cword, dstaddr,
info->write_tout, "write");
else
return flash_full_status_check(info, sect,
info->write_tout, "write");
}
#ifdef CONFIG_SYS_FLASH_USE_BUFFER_WRITE
static int flash_write_cfibuffer(flash_info_t *info, ulong dest, uchar *cp,
int len)
{
flash_sect_t sector;
int cnt;
int retcode;
u8 *src = cp;
u8 *dst = (u8 *)dest;
u8 *dst2 = dst;
int flag = 1;
uint offset = 0;
unsigned int shift;
uchar write_cmd;
switch (info->portwidth) {
case FLASH_CFI_8BIT:
shift = 0;
break;
case FLASH_CFI_16BIT:
shift = 1;
break;
case FLASH_CFI_32BIT:
shift = 2;
break;
case FLASH_CFI_64BIT:
shift = 3;
break;
default:
retcode = FL_ERR_INVAL;
goto out_unmap;
}
cnt = len >> shift;
while ((cnt-- > 0) && (flag == 1)) {
switch (info->portwidth) {
case FLASH_CFI_8BIT:
flag = ((flash_read8(dst2) & flash_read8(src)) ==
flash_read8(src));
src += 1, dst2 += 1;
break;
case FLASH_CFI_16BIT:
flag = ((flash_read16(dst2) & flash_read16(src)) ==
flash_read16(src));
src += 2, dst2 += 2;
break;
case FLASH_CFI_32BIT:
flag = ((flash_read32(dst2) & flash_read32(src)) ==
flash_read32(src));
src += 4, dst2 += 4;
break;
case FLASH_CFI_64BIT:
flag = ((flash_read64(dst2) & flash_read64(src)) ==
flash_read64(src));
src += 8, dst2 += 8;
break;
}
}
if (!flag) {
retcode = FL_ERR_NOT_ERASED;
goto out_unmap;
}
src = cp;
sector = find_sector(info, dest);
switch (info->vendor) {
case CFI_CMDSET_INTEL_PROG_REGIONS:
case CFI_CMDSET_INTEL_STANDARD:
case CFI_CMDSET_INTEL_EXTENDED:
write_cmd = (info->vendor == CFI_CMDSET_INTEL_PROG_REGIONS) ?
FLASH_CMD_WRITE_BUFFER_PROG :
FLASH_CMD_WRITE_TO_BUFFER;
flash_write_cmd(info, sector, 0, FLASH_CMD_CLEAR_STATUS);
flash_write_cmd(info, sector, 0, FLASH_CMD_READ_STATUS);
flash_write_cmd(info, sector, 0, write_cmd);
retcode = flash_status_check(info, sector,
info->buffer_write_tout,
"write to buffer");
if (retcode == FL_ERR_OK) {
/* reduce the number of loops by the width of
* the port
*/
cnt = len >> shift;
flash_write_cmd(info, sector, 0, cnt - 1);
while (cnt-- > 0) {
switch (info->portwidth) {
case FLASH_CFI_8BIT:
flash_write8(flash_read8(src), dst);
src += 1, dst += 1;
break;
case FLASH_CFI_16BIT:
flash_write16(flash_read16(src), dst);
src += 2, dst += 2;
break;
case FLASH_CFI_32BIT:
flash_write32(flash_read32(src), dst);
src += 4, dst += 4;
break;
case FLASH_CFI_64BIT:
flash_write64(flash_read64(src), dst);
src += 8, dst += 8;
break;
default:
retcode = FL_ERR_INVAL;
goto out_unmap;
}
}
flash_write_cmd(info, sector, 0,
FLASH_CMD_WRITE_BUFFER_CONFIRM);
retcode = flash_full_status_check(
info, sector, info->buffer_write_tout,
"buffer write");
}
break;
case CFI_CMDSET_AMD_STANDARD:
case CFI_CMDSET_AMD_EXTENDED:
flash_unlock_seq(info, sector);
#ifdef CONFIG_FLASH_SPANSION_S29WS_N
offset = ((unsigned long)dst - info->start[sector]) >> shift;
#endif
flash_write_cmd(info, sector, offset, AMD_CMD_WRITE_TO_BUFFER);
cnt = len >> shift;
flash_write_cmd(info, sector, offset, cnt - 1);
switch (info->portwidth) {
case FLASH_CFI_8BIT:
while (cnt-- > 0) {
flash_write8(flash_read8(src), dst);
src += 1, dst += 1;
}
break;
case FLASH_CFI_16BIT:
while (cnt-- > 0) {
flash_write16(flash_read16(src), dst);
src += 2, dst += 2;
}
break;
case FLASH_CFI_32BIT:
while (cnt-- > 0) {
flash_write32(flash_read32(src), dst);
src += 4, dst += 4;
}
break;
case FLASH_CFI_64BIT:
while (cnt-- > 0) {
flash_write64(flash_read64(src), dst);
src += 8, dst += 8;
}
break;
default:
retcode = FL_ERR_INVAL;
goto out_unmap;
}
flash_write_cmd(info, sector, 0, AMD_CMD_WRITE_BUFFER_CONFIRM);
if (use_flash_status_poll(info))
retcode = flash_status_poll(info, src - (1 << shift),
dst - (1 << shift),
info->buffer_write_tout,
"buffer write");
else
retcode = flash_full_status_check(info, sector,
info->buffer_write_tout,
"buffer write");
break;
default:
debug("Unknown Command Set\n");
retcode = FL_ERR_INVAL;
break;
}
out_unmap:
return retcode;
}
#endif /* CONFIG_SYS_FLASH_USE_BUFFER_WRITE */
/*-----------------------------------------------------------------------
*/
int flash_erase(flash_info_t *info, int s_first, int s_last)
{
int rcode = 0;
int prot;
flash_sect_t sect;
int st;
if (info->flash_id != FLASH_MAN_CFI) {
puts("Can't erase unknown flash type - aborted\n");
return 1;
}
if (s_first < 0 || s_first > s_last) {
puts("- no sectors to erase\n");
return 1;
}
prot = 0;
for (sect = s_first; sect <= s_last; ++sect)
if (info->protect[sect])
prot++;
if (prot) {
printf("- Warning: %d protected sectors will not be erased!\n",
prot);
} else if (flash_verbose) {
putc('\n');
}
for (sect = s_first; sect <= s_last; sect++) {
if (ctrlc()) {
printf("\n");
return 1;
}
if (info->protect[sect] == 0) { /* not protected */
#ifdef CONFIG_SYS_FLASH_CHECK_BLANK_BEFORE_ERASE
int k;
int size;
int erased;
u32 *flash;
/*
* Check if whole sector is erased
*/
size = flash_sector_size(info, sect);
erased = 1;
flash = (u32 *)info->start[sect];
/* divide by 4 for longword access */
size = size >> 2;
for (k = 0; k < size; k++) {
if (flash_read32(flash++) != 0xffffffff) {
erased = 0;
break;
}
}
if (erased) {
if (flash_verbose)
putc(',');
continue;
}
#endif
switch (info->vendor) {
case CFI_CMDSET_INTEL_PROG_REGIONS:
case CFI_CMDSET_INTEL_STANDARD:
case CFI_CMDSET_INTEL_EXTENDED:
flash_write_cmd(info, sect, 0,
FLASH_CMD_CLEAR_STATUS);
flash_write_cmd(info, sect, 0,
FLASH_CMD_BLOCK_ERASE);
flash_write_cmd(info, sect, 0,
FLASH_CMD_ERASE_CONFIRM);
break;
case CFI_CMDSET_AMD_STANDARD:
case CFI_CMDSET_AMD_EXTENDED:
flash_unlock_seq(info, sect);
flash_write_cmd(info, sect,
info->addr_unlock1,
AMD_CMD_ERASE_START);
flash_unlock_seq(info, sect);
flash_write_cmd(info, sect, 0,
info->cmd_erase_sector);
break;
#ifdef CONFIG_FLASH_CFI_LEGACY
case CFI_CMDSET_AMD_LEGACY:
flash_unlock_seq(info, 0);
flash_write_cmd(info, 0, info->addr_unlock1,
AMD_CMD_ERASE_START);
flash_unlock_seq(info, 0);
flash_write_cmd(info, sect, 0,
AMD_CMD_ERASE_SECTOR);
break;
#endif
default:
debug("Unknown flash vendor %d\n",
info->vendor);
break;
}
if (use_flash_status_poll(info)) {
cfiword_t cword;
void *dest;
cword.w64 = 0xffffffffffffffffULL;
dest = flash_map(info, sect, 0);
st = flash_status_poll(info, &cword, dest,
info->erase_blk_tout,
"erase");
flash_unmap(info, sect, 0, dest);
} else {
st = flash_full_status_check(info, sect,
info->erase_blk_tout,
"erase");
}
if (st)
rcode = 1;
else if (flash_verbose)
putc('.');
}
}
if (flash_verbose)
puts(" done\n");
return rcode;
}
#ifdef CONFIG_SYS_FLASH_EMPTY_INFO
static int sector_erased(flash_info_t *info, int i)
{
int k;
int size;
u32 *flash;
/*
* Check if whole sector is erased
*/
size = flash_sector_size(info, i);
flash = (u32 *)info->start[i];
/* divide by 4 for longword access */
size = size >> 2;
for (k = 0; k < size; k++) {
if (flash_read32(flash++) != 0xffffffff)
return 0; /* not erased */
}
return 1; /* erased */
}
#endif /* CONFIG_SYS_FLASH_EMPTY_INFO */
void flash_print_info(flash_info_t *info)
{
int i;
if (info->flash_id != FLASH_MAN_CFI) {
puts("missing or unknown FLASH type\n");
return;
}
printf("%s flash (%d x %d)",
info->name,
(info->portwidth << 3), (info->chipwidth << 3));
if (info->size < 1024 * 1024)
printf(" Size: %ld kB in %d Sectors\n",
info->size >> 10, info->sector_count);
else
printf(" Size: %ld MB in %d Sectors\n",
info->size >> 20, info->sector_count);
printf(" ");
switch (info->vendor) {
case CFI_CMDSET_INTEL_PROG_REGIONS:
printf("Intel Prog Regions");
break;
case CFI_CMDSET_INTEL_STANDARD:
printf("Intel Standard");
break;
case CFI_CMDSET_INTEL_EXTENDED:
printf("Intel Extended");
break;
case CFI_CMDSET_AMD_STANDARD:
printf("AMD Standard");
break;
case CFI_CMDSET_AMD_EXTENDED:
printf("AMD Extended");
break;
#ifdef CONFIG_FLASH_CFI_LEGACY
case CFI_CMDSET_AMD_LEGACY:
printf("AMD Legacy");
break;
#endif
default:
printf("Unknown (%d)", info->vendor);
break;
}
printf(" command set, Manufacturer ID: 0x%02X, Device ID: 0x",
info->manufacturer_id);
printf(info->chipwidth == FLASH_CFI_16BIT ? "%04X" : "%02X",
info->device_id);
if ((info->device_id & 0xff) == 0x7E) {
printf(info->chipwidth == FLASH_CFI_16BIT ? "%04X" : "%02X",
info->device_id2);
}
if (info->vendor == CFI_CMDSET_AMD_STANDARD && info->legacy_unlock)
printf("\n Advanced Sector Protection (PPB) enabled");
printf("\n Erase timeout: %ld ms, write timeout: %ld ms\n",
info->erase_blk_tout, info->write_tout);
if (info->buffer_size > 1) {
printf(" Buffer write timeout: %ld ms, ",
info->buffer_write_tout);
printf("buffer size: %d bytes\n", info->buffer_size);
}
puts("\n Sector Start Addresses:");
for (i = 0; i < info->sector_count; ++i) {
if (ctrlc())
break;
if ((i % 5) == 0)
putc('\n');
#ifdef CONFIG_SYS_FLASH_EMPTY_INFO
/* print empty and read-only info */
printf(" %08lX %c %s ",
info->start[i],
sector_erased(info, i) ? 'E' : ' ',
info->protect[i] ? "RO" : " ");
#else /* ! CONFIG_SYS_FLASH_EMPTY_INFO */
printf(" %08lX %s ",
info->start[i],
info->protect[i] ? "RO" : " ");
#endif
}
putc('\n');
}
/*-----------------------------------------------------------------------
* This is used in a few places in write_buf() to show programming
* progress. Making it a function is nasty because it needs to do side
* effect updates to digit and dots. Repeated code is nasty too, so
* we define it once here.
*/
#if CONFIG_FLASH_SHOW_PROGRESS
#define FLASH_SHOW_PROGRESS(scale, dots, digit, dots_sub) \
if (flash_verbose) { \
dots -= dots_sub; \
if (scale > 0 && dots <= 0) { \
if ((digit % 5) == 0) \
printf("%d", digit / 5); \
else \
putc('.'); \
digit--; \
dots += scale; \
} \
}
#else
#define FLASH_SHOW_PROGRESS(scale, dots, digit, dots_sub)
#endif
/*-----------------------------------------------------------------------
* Copy memory to flash, returns:
* 0 - OK
* 1 - write timeout
* 2 - Flash not erased
*/
int write_buff(flash_info_t *info, uchar *src, ulong addr, ulong cnt)
{
ulong wp;
uchar *p;
int aln;
cfiword_t cword;
int i, rc;
#ifdef CONFIG_SYS_FLASH_USE_BUFFER_WRITE
int buffered_size;
#endif
#if CONFIG_FLASH_SHOW_PROGRESS
int digit = CONFIG_FLASH_SHOW_PROGRESS;
int scale = 0;
int dots = 0;
/*
* Suppress if there are fewer than CONFIG_FLASH_SHOW_PROGRESS writes.
*/
if (cnt >= CONFIG_FLASH_SHOW_PROGRESS) {
scale = (int)((cnt + CONFIG_FLASH_SHOW_PROGRESS - 1) /
CONFIG_FLASH_SHOW_PROGRESS);
}
#endif
/* get lower aligned address */
wp = (addr & ~(info->portwidth - 1));
/* handle unaligned start */
aln = addr - wp;
if (aln != 0) {
cword.w32 = 0;
p = (uchar *)wp;
for (i = 0; i < aln; ++i)
flash_add_byte(info, &cword, flash_read8(p + i));
for (; (i < info->portwidth) && (cnt > 0); i++) {
flash_add_byte(info, &cword, *src++);
cnt--;
}
for (; (cnt == 0) && (i < info->portwidth); ++i)
flash_add_byte(info, &cword, flash_read8(p + i));
rc = flash_write_cfiword(info, wp, cword);
if (rc != 0)
return rc;
wp += i;
FLASH_SHOW_PROGRESS(scale, dots, digit, i);
}
/* handle the aligned part */
#ifdef CONFIG_SYS_FLASH_USE_BUFFER_WRITE
buffered_size = (info->portwidth / info->chipwidth);
buffered_size *= info->buffer_size;
while (cnt >= info->portwidth) {
/* prohibit buffer write when buffer_size is 1 */
if (info->buffer_size == 1) {
cword.w32 = 0;
for (i = 0; i < info->portwidth; i++)
flash_add_byte(info, &cword, *src++);
rc = flash_write_cfiword(info, wp, cword);
if (rc != 0)
return rc;
wp += info->portwidth;
cnt -= info->portwidth;
continue;
}
/* write buffer until next buffered_size aligned boundary */
i = buffered_size - (wp % buffered_size);
if (i > cnt)
i = cnt;
rc = flash_write_cfibuffer(info, wp, src, i);
if (rc != FL_ERR_OK)
return rc;
i -= i & (info->portwidth - 1);
wp += i;
src += i;
cnt -= i;
FLASH_SHOW_PROGRESS(scale, dots, digit, i);
/* Only check every once in a while */
if ((cnt & 0xFFFF) < buffered_size && ctrlc())
return FL_ERR_ABORTED;
}
#else
while (cnt >= info->portwidth) {
cword.w32 = 0;
for (i = 0; i < info->portwidth; i++)
flash_add_byte(info, &cword, *src++);
rc = flash_write_cfiword(info, wp, cword);
if (rc != 0)
return rc;
wp += info->portwidth;
cnt -= info->portwidth;
FLASH_SHOW_PROGRESS(scale, dots, digit, info->portwidth);
/* Only check every once in a while */
if ((cnt & 0xFFFF) < info->portwidth && ctrlc())
return FL_ERR_ABORTED;
}
#endif /* CONFIG_SYS_FLASH_USE_BUFFER_WRITE */
if (cnt == 0)
return (0);
/*
* handle unaligned tail bytes
*/
cword.w32 = 0;
p = (uchar *)wp;
for (i = 0; (i < info->portwidth) && (cnt > 0); ++i) {
flash_add_byte(info, &cword, *src++);
--cnt;
}
for (; i < info->portwidth; ++i)
flash_add_byte(info, &cword, flash_read8(p + i));
return flash_write_cfiword(info, wp, cword);
}
static inline int manufact_match(flash_info_t *info, u32 manu)
{
return info->manufacturer_id == ((manu & FLASH_VENDMASK) >> 16);
}
/*-----------------------------------------------------------------------
*/
#ifdef CONFIG_SYS_FLASH_PROTECTION
static int cfi_protect_bugfix(flash_info_t *info, long sector, int prot)
{
if (manufact_match(info, INTEL_MANUFACT) &&
info->device_id == NUMONYX_256MBIT) {
/*
* see errata called
* "Numonyx Axcell P33/P30 Specification Update" :)
*/
flash_write_cmd(info, sector, 0, FLASH_CMD_READ_ID);
if (!flash_isequal(info, sector, FLASH_OFFSET_PROTECT,
prot)) {
/*
* cmd must come before FLASH_CMD_PROTECT + 20us
* Disable interrupts which might cause a timeout here.
*/
int flag = disable_interrupts();
unsigned short cmd;
if (prot)
cmd = FLASH_CMD_PROTECT_SET;
else
cmd = FLASH_CMD_PROTECT_CLEAR;
flash_write_cmd(info, sector, 0, FLASH_CMD_PROTECT);
flash_write_cmd(info, sector, 0, cmd);
/* re-enable interrupts if necessary */
if (flag)
enable_interrupts();
}
return 1;
}
return 0;
}
int flash_real_protect(flash_info_t *info, long sector, int prot)
{
int retcode = 0;
switch (info->vendor) {
case CFI_CMDSET_INTEL_PROG_REGIONS:
case CFI_CMDSET_INTEL_STANDARD:
case CFI_CMDSET_INTEL_EXTENDED:
if (!cfi_protect_bugfix(info, sector, prot)) {
flash_write_cmd(info, sector, 0,
FLASH_CMD_CLEAR_STATUS);
flash_write_cmd(info, sector, 0,
FLASH_CMD_PROTECT);
if (prot)
flash_write_cmd(info, sector, 0,
FLASH_CMD_PROTECT_SET);
else
flash_write_cmd(info, sector, 0,
FLASH_CMD_PROTECT_CLEAR);
}
break;
case CFI_CMDSET_AMD_EXTENDED:
case CFI_CMDSET_AMD_STANDARD:
/* U-Boot only checks the first byte */
if (manufact_match(info, ATM_MANUFACT)) {
if (prot) {
flash_unlock_seq(info, 0);
flash_write_cmd(info, 0,
info->addr_unlock1,
ATM_CMD_SOFTLOCK_START);
flash_unlock_seq(info, 0);
flash_write_cmd(info, sector, 0,
ATM_CMD_LOCK_SECT);
} else {
flash_write_cmd(info, 0,
info->addr_unlock1,
AMD_CMD_UNLOCK_START);
if (info->device_id == ATM_ID_BV6416)
flash_write_cmd(info, sector,
0, ATM_CMD_UNLOCK_SECT);
}
}
if (info->legacy_unlock) {
int flag = disable_interrupts();
int lock_flag;
flash_unlock_seq(info, 0);
flash_write_cmd(info, 0, info->addr_unlock1,
AMD_CMD_SET_PPB_ENTRY);
lock_flag = flash_isset(info, sector, 0, 0x01);
if (prot) {
if (lock_flag) {
flash_write_cmd(info, sector, 0,
AMD_CMD_PPB_LOCK_BC1);
flash_write_cmd(info, sector, 0,
AMD_CMD_PPB_LOCK_BC2);
}
debug("sector %ld %slocked\n", sector,
lock_flag ? "" : "already ");
} else {
if (!lock_flag) {
debug("unlock %ld\n", sector);
flash_write_cmd(info, 0, 0,
AMD_CMD_PPB_UNLOCK_BC1);
flash_write_cmd(info, 0, 0,
AMD_CMD_PPB_UNLOCK_BC2);
}
debug("sector %ld %sunlocked\n", sector,
!lock_flag ? "" : "already ");
}
if (flag)
enable_interrupts();
if (flash_status_check(info, sector,
info->erase_blk_tout,
prot ? "protect" : "unprotect"))
printf("status check error\n");
flash_write_cmd(info, 0, 0,
AMD_CMD_SET_PPB_EXIT_BC1);
flash_write_cmd(info, 0, 0,
AMD_CMD_SET_PPB_EXIT_BC2);
}
break;
#ifdef CONFIG_FLASH_CFI_LEGACY
case CFI_CMDSET_AMD_LEGACY:
flash_write_cmd(info, sector, 0, FLASH_CMD_CLEAR_STATUS);
flash_write_cmd(info, sector, 0, FLASH_CMD_PROTECT);
if (prot)
flash_write_cmd(info, sector, 0,
FLASH_CMD_PROTECT_SET);
else
flash_write_cmd(info, sector, 0,
FLASH_CMD_PROTECT_CLEAR);
#endif
};
/*
* Flash needs to be in status register read mode for
* flash_full_status_check() to work correctly
*/
flash_write_cmd(info, sector, 0, FLASH_CMD_READ_STATUS);
retcode = flash_full_status_check(info, sector, info->erase_blk_tout,
prot ? "protect" : "unprotect");
if (retcode == 0) {
info->protect[sector] = prot;
/*
* On some of Intel's flash chips (marked via legacy_unlock)
* unprotect unprotects all locking.
*/
if (prot == 0 && info->legacy_unlock) {
flash_sect_t i;
for (i = 0; i < info->sector_count; i++) {
if (info->protect[i])
flash_real_protect(info, i, 1);
}
}
}
return retcode;
}
/*-----------------------------------------------------------------------
* flash_read_user_serial - read the OneTimeProgramming cells
*/
void flash_read_user_serial(flash_info_t *info, void *buffer, int offset,
int len)
{
uchar *src;
uchar *dst;
dst = buffer;
src = flash_map(info, 0, FLASH_OFFSET_USER_PROTECTION);
flash_write_cmd(info, 0, 0, FLASH_CMD_READ_ID);
memcpy(dst, src + offset, len);
flash_write_cmd(info, 0, 0, info->cmd_reset);
udelay(1);
flash_unmap(info, 0, FLASH_OFFSET_USER_PROTECTION, src);
}
/*
* flash_read_factory_serial - read the device Id from the protection area
*/
void flash_read_factory_serial(flash_info_t *info, void *buffer, int offset,
int len)
{
uchar *src;
src = flash_map(info, 0, FLASH_OFFSET_INTEL_PROTECTION);
flash_write_cmd(info, 0, 0, FLASH_CMD_READ_ID);
memcpy(buffer, src + offset, len);
flash_write_cmd(info, 0, 0, info->cmd_reset);
udelay(1);
flash_unmap(info, 0, FLASH_OFFSET_INTEL_PROTECTION, src);
}
#endif /* CONFIG_SYS_FLASH_PROTECTION */
/*-----------------------------------------------------------------------
* Reverse the order of the erase regions in the CFI QRY structure.
* This is needed for chips that are either a) correctly detected as
* top-boot, or b) buggy.
*/
static void cfi_reverse_geometry(struct cfi_qry *qry)
{
unsigned int i, j;
u32 tmp;
for (i = 0, j = qry->num_erase_regions - 1; i < j; i++, j--) {
tmp = get_unaligned(&qry->erase_region_info[i]);
put_unaligned(get_unaligned(&qry->erase_region_info[j]),
&qry->erase_region_info[i]);
put_unaligned(tmp, &qry->erase_region_info[j]);
}
}
/*-----------------------------------------------------------------------
* read jedec ids from device and set corresponding fields in info struct
*
* Note: assume cfi->vendor, cfi->portwidth and cfi->chipwidth are correct
*
*/
static void cmdset_intel_read_jedec_ids(flash_info_t *info)
{
flash_write_cmd(info, 0, 0, FLASH_CMD_RESET);
udelay(1);
flash_write_cmd(info, 0, 0, FLASH_CMD_READ_ID);
udelay(1000); /* some flash are slow to respond */
info->manufacturer_id = flash_read_uchar(info,
FLASH_OFFSET_MANUFACTURER_ID);
info->device_id = (info->chipwidth == FLASH_CFI_16BIT) ?
flash_read_word(info, FLASH_OFFSET_DEVICE_ID) :
flash_read_uchar(info, FLASH_OFFSET_DEVICE_ID);
flash_write_cmd(info, 0, 0, FLASH_CMD_RESET);
}
static int cmdset_intel_init(flash_info_t *info, struct cfi_qry *qry)
{
info->cmd_reset = FLASH_CMD_RESET;
cmdset_intel_read_jedec_ids(info);
flash_write_cmd(info, 0, info->cfi_offset, FLASH_CMD_CFI);
#ifdef CONFIG_SYS_FLASH_PROTECTION
/* read legacy lock/unlock bit from intel flash */
if (info->ext_addr) {
info->legacy_unlock =
flash_read_uchar(info, info->ext_addr + 5) & 0x08;
}
#endif
return 0;
}
static void cmdset_amd_read_jedec_ids(flash_info_t *info)
{
ushort bank_id = 0;
uchar manu_id;
uchar feature;
flash_write_cmd(info, 0, 0, AMD_CMD_RESET);
flash_unlock_seq(info, 0);
flash_write_cmd(info, 0, info->addr_unlock1, FLASH_CMD_READ_ID);
udelay(1000); /* some flash are slow to respond */
manu_id = flash_read_uchar(info, FLASH_OFFSET_MANUFACTURER_ID);
/* JEDEC JEP106Z specifies ID codes up to bank 7 */
while (manu_id == FLASH_CONTINUATION_CODE && bank_id < 0x800) {
bank_id += 0x100;
manu_id = flash_read_uchar(info,
bank_id | FLASH_OFFSET_MANUFACTURER_ID);
}
info->manufacturer_id = manu_id;
debug("info->ext_addr = 0x%x, cfi_version = 0x%x\n",
info->ext_addr, info->cfi_version);
if (info->ext_addr && info->cfi_version >= 0x3134) {
/* read software feature (at 0x53) */
feature = flash_read_uchar(info, info->ext_addr + 0x13);
debug("feature = 0x%x\n", feature);
info->sr_supported = feature & 0x1;
}
switch (info->chipwidth) {
case FLASH_CFI_8BIT:
info->device_id = flash_read_uchar(info,
FLASH_OFFSET_DEVICE_ID);
if (info->device_id == 0x7E) {
/* AMD 3-byte (expanded) device ids */
info->device_id2 = flash_read_uchar(info,
FLASH_OFFSET_DEVICE_ID2);
info->device_id2 <<= 8;
info->device_id2 |= flash_read_uchar(info,
FLASH_OFFSET_DEVICE_ID3);
}
break;
case FLASH_CFI_16BIT:
info->device_id = flash_read_word(info,
FLASH_OFFSET_DEVICE_ID);
if ((info->device_id & 0xff) == 0x7E) {
/* AMD 3-byte (expanded) device ids */
info->device_id2 = flash_read_uchar(info,
FLASH_OFFSET_DEVICE_ID2);
info->device_id2 <<= 8;
info->device_id2 |= flash_read_uchar(info,
FLASH_OFFSET_DEVICE_ID3);
}
break;
default:
break;
}
flash_write_cmd(info, 0, 0, AMD_CMD_RESET);
udelay(1);
}
static int cmdset_amd_init(flash_info_t *info, struct cfi_qry *qry)
{
info->cmd_reset = AMD_CMD_RESET;
info->cmd_erase_sector = AMD_CMD_ERASE_SECTOR;
cmdset_amd_read_jedec_ids(info);
flash_write_cmd(info, 0, info->cfi_offset, FLASH_CMD_CFI);
#ifdef CONFIG_SYS_FLASH_PROTECTION
if (info->ext_addr) {
/* read sector protect/unprotect scheme (at 0x49) */
if (flash_read_uchar(info, info->ext_addr + 9) == 0x8)
info->legacy_unlock = 1;
}
#endif
return 0;
}
#ifdef CONFIG_FLASH_CFI_LEGACY
static void flash_read_jedec_ids(flash_info_t *info)
{
info->manufacturer_id = 0;
info->device_id = 0;
info->device_id2 = 0;
switch (info->vendor) {
case CFI_CMDSET_INTEL_PROG_REGIONS:
case CFI_CMDSET_INTEL_STANDARD:
case CFI_CMDSET_INTEL_EXTENDED:
cmdset_intel_read_jedec_ids(info);
break;
case CFI_CMDSET_AMD_STANDARD:
case CFI_CMDSET_AMD_EXTENDED:
cmdset_amd_read_jedec_ids(info);
break;
default:
break;
}
}
/*-----------------------------------------------------------------------
* Call board code to request info about non-CFI flash.
* board_flash_get_legacy needs to fill in at least:
* info->portwidth, info->chipwidth and info->interface for Jedec probing.
*/
static int flash_detect_legacy(phys_addr_t base, int banknum)
{
flash_info_t *info = &flash_info[banknum];
if (board_flash_get_legacy(base, banknum, info)) {
/* board code may have filled info completely. If not, we
* use JEDEC ID probing.
*/
if (!info->vendor) {
int modes[] = {
CFI_CMDSET_AMD_STANDARD,
CFI_CMDSET_INTEL_STANDARD
};
int i;
for (i = 0; i < ARRAY_SIZE(modes); i++) {
info->vendor = modes[i];
info->start[0] =
(ulong)map_physmem(base,
info->portwidth,
MAP_NOCACHE);
if (info->portwidth == FLASH_CFI_8BIT &&
info->interface == FLASH_CFI_X8X16) {
info->addr_unlock1 = 0x2AAA;
info->addr_unlock2 = 0x5555;
} else {
info->addr_unlock1 = 0x5555;
info->addr_unlock2 = 0x2AAA;
}
flash_read_jedec_ids(info);
debug("JEDEC PROBE: ID %x %x %x\n",
info->manufacturer_id,
info->device_id,
info->device_id2);
if (jedec_flash_match(info, info->start[0]))
break;
unmap_physmem((void *)info->start[0],
info->portwidth);
}
}
switch (info->vendor) {
case CFI_CMDSET_INTEL_PROG_REGIONS:
case CFI_CMDSET_INTEL_STANDARD:
case CFI_CMDSET_INTEL_EXTENDED:
info->cmd_reset = FLASH_CMD_RESET;
break;
case CFI_CMDSET_AMD_STANDARD:
case CFI_CMDSET_AMD_EXTENDED:
case CFI_CMDSET_AMD_LEGACY:
info->cmd_reset = AMD_CMD_RESET;
break;
}
info->flash_id = FLASH_MAN_CFI;
return 1;
}
return 0; /* use CFI */
}
#else
static inline int flash_detect_legacy(phys_addr_t base, int banknum)
{
return 0; /* use CFI */
}
#endif
/*-----------------------------------------------------------------------
* detect if flash is compatible with the Common Flash Interface (CFI)
* http://www.jedec.org/download/search/jesd68.pdf
*/
static void flash_read_cfi(flash_info_t *info, void *buf, unsigned int start,
size_t len)
{
u8 *p = buf;
unsigned int i;
for (i = 0; i < len; i++)
p[i] = flash_read_uchar(info, start + i);
}
static void __flash_cmd_reset(flash_info_t *info)
{
/*
* We do not yet know what kind of commandset to use, so we issue
* the reset command in both Intel and AMD variants, in the hope
* that AMD flash roms ignore the Intel command.
*/
flash_write_cmd(info, 0, 0, AMD_CMD_RESET);
udelay(1);
flash_write_cmd(info, 0, 0, FLASH_CMD_RESET);
}
void flash_cmd_reset(flash_info_t *info)
__attribute__((weak, alias("__flash_cmd_reset")));
static int __flash_detect_cfi(flash_info_t *info, struct cfi_qry *qry)
{
int cfi_offset;
/* Issue FLASH reset command */
flash_cmd_reset(info);
for (cfi_offset = 0; cfi_offset < ARRAY_SIZE(flash_offset_cfi);
cfi_offset++) {
flash_write_cmd(info, 0, flash_offset_cfi[cfi_offset],
FLASH_CMD_CFI);
if (flash_isequal(info, 0, FLASH_OFFSET_CFI_RESP, 'Q') &&
flash_isequal(info, 0, FLASH_OFFSET_CFI_RESP + 1, 'R') &&
flash_isequal(info, 0, FLASH_OFFSET_CFI_RESP + 2, 'Y')) {
flash_read_cfi(info, qry, FLASH_OFFSET_CFI_RESP,
sizeof(struct cfi_qry));
info->interface = le16_to_cpu(qry->interface_desc);
/* Some flash chips can support multiple bus widths.
* In this case, override the interface width and
* limit it to the port width.
*/
if ((info->interface == FLASH_CFI_X8X16) &&
(info->portwidth == FLASH_CFI_8BIT)) {
debug("Overriding 16-bit interface width to"
" 8-bit port width\n");
info->interface = FLASH_CFI_X8;
} else if ((info->interface == FLASH_CFI_X16X32) &&
(info->portwidth == FLASH_CFI_16BIT)) {
debug("Overriding 16-bit interface width to"
" 16-bit port width\n");
info->interface = FLASH_CFI_X16;
}
info->cfi_offset = flash_offset_cfi[cfi_offset];
debug("device interface is %d\n",
info->interface);
debug("found port %d chip %d chip_lsb %d ",
info->portwidth, info->chipwidth, info->chip_lsb);
debug("port %d bits chip %d bits\n",
info->portwidth << CFI_FLASH_SHIFT_WIDTH,
info->chipwidth << CFI_FLASH_SHIFT_WIDTH);
/* calculate command offsets as in the Linux driver */
info->addr_unlock1 = 0x555;
info->addr_unlock2 = 0x2aa;
/*
* modify the unlock address if we are
* in compatibility mode
*/
if (/* x8/x16 in x8 mode */
(info->chipwidth == FLASH_CFI_BY8 &&
info->interface == FLASH_CFI_X8X16) ||
/* x16/x32 in x16 mode */
(info->chipwidth == FLASH_CFI_BY16 &&
info->interface == FLASH_CFI_X16X32)) {
info->addr_unlock1 = 0xaaa;
info->addr_unlock2 = 0x555;
}
info->name = "CFI conformant";
return 1;
}
}
return 0;
}
static int flash_detect_cfi(flash_info_t *info, struct cfi_qry *qry)
{
debug("flash detect cfi\n");
for (info->portwidth = CONFIG_SYS_FLASH_CFI_WIDTH;
info->portwidth <= FLASH_CFI_64BIT; info->portwidth <<= 1) {
for (info->chipwidth = FLASH_CFI_BY8;
info->chipwidth <= info->portwidth;
info->chipwidth <<= 1) {
/*
* First, try detection without shifting the addresses
* for 8bit devices (16bit wide connection)
*/
info->chip_lsb = 0;
if (__flash_detect_cfi(info, qry))
return 1;
/*
* Not detected, so let's try with shifting
* for 8bit devices
*/
info->chip_lsb = 1;
if (__flash_detect_cfi(info, qry))
return 1;
}
}
debug("not found\n");
return 0;
}
/*
* Manufacturer-specific quirks. Add workarounds for geometry
* reversal, etc. here.
*/
static void flash_fixup_amd(flash_info_t *info, struct cfi_qry *qry)
{
/* check if flash geometry needs reversal */
if (qry->num_erase_regions > 1) {
/* reverse geometry if top boot part */
if (info->cfi_version < 0x3131) {
/* CFI < 1.1, try to guess from device id */
if ((info->device_id & 0x80) != 0)
cfi_reverse_geometry(qry);
} else if (flash_read_uchar(info, info->ext_addr + 0xf) == 3) {
/* CFI >= 1.1, deduct from top/bottom flag */
/* note: ext_addr is valid since cfi_version > 0 */
cfi_reverse_geometry(qry);
}
}
}
static void flash_fixup_atmel(flash_info_t *info, struct cfi_qry *qry)
{
int reverse_geometry = 0;
/* Check the "top boot" bit in the PRI */
if (info->ext_addr && !(flash_read_uchar(info, info->ext_addr + 6) & 1))
reverse_geometry = 1;
/* AT49BV6416(T) list the erase regions in the wrong order.
* However, the device ID is identical with the non-broken
* AT49BV642D they differ in the high byte.
*/
if (info->device_id == 0xd6 || info->device_id == 0xd2)
reverse_geometry = !reverse_geometry;
if (reverse_geometry)
cfi_reverse_geometry(qry);
}
static void flash_fixup_stm(flash_info_t *info, struct cfi_qry *qry)
{
/* check if flash geometry needs reversal */
if (qry->num_erase_regions > 1) {
/* reverse geometry if top boot part */
if (info->cfi_version < 0x3131) {
/* CFI < 1.1, guess by device id */
if (info->device_id == 0x22CA || /* M29W320DT */
info->device_id == 0x2256 || /* M29W320ET */
info->device_id == 0x22D7) { /* M29W800DT */
cfi_reverse_geometry(qry);
}
} else if (flash_read_uchar(info, info->ext_addr + 0xf) == 3) {
/* CFI >= 1.1, deduct from top/bottom flag */
/* note: ext_addr is valid since cfi_version > 0 */
cfi_reverse_geometry(qry);
}
}
}
static void flash_fixup_sst(flash_info_t *info, struct cfi_qry *qry)
{
/*
* SST, for many recent nor parallel flashes, says they are
* CFI-conformant. This is not true, since qry struct.
* reports a std. AMD command set (0x0002), while SST allows to
* erase two different sector sizes for the same memory.
* 64KB sector (SST call it block) needs 0x30 to be erased.
* 4KB sector (SST call it sector) needs 0x50 to be erased.
* Since CFI query detect the 4KB number of sectors, users expects
* a sector granularity of 4KB, and it is here set.
*/
if (info->device_id == 0x5D23 || /* SST39VF3201B */
info->device_id == 0x5C23) { /* SST39VF3202B */
/* set sector granularity to 4KB */
info->cmd_erase_sector = 0x50;
}
}
static void flash_fixup_num(flash_info_t *info, struct cfi_qry *qry)
{
/*
* The M29EW devices seem to report the CFI information wrong
* when it's in 8 bit mode.
* There's an app note from Numonyx on this issue.
* So adjust the buffer size for M29EW while operating in 8-bit mode
*/
if (qry->max_buf_write_size > 0x8 &&
info->device_id == 0x7E &&
(info->device_id2 == 0x2201 ||
info->device_id2 == 0x2301 ||
info->device_id2 == 0x2801 ||
info->device_id2 == 0x4801)) {
debug("Adjusted buffer size on Numonyx flash");
debug(" M29EW family in 8 bit mode\n");
qry->max_buf_write_size = 0x8;
}
}
/*
* The following code cannot be run from FLASH!
*
*/
ulong flash_get_size(phys_addr_t base, int banknum)
{
flash_info_t *info = &flash_info[banknum];
int i, j;
flash_sect_t sect_cnt;
phys_addr_t sector;
unsigned long tmp;
int size_ratio;
uchar num_erase_regions;
int erase_region_size;
int erase_region_count;
struct cfi_qry qry;
unsigned long max_size;
memset(&qry, 0, sizeof(qry));
info->ext_addr = 0;
info->cfi_version = 0;
#ifdef CONFIG_SYS_FLASH_PROTECTION
info->legacy_unlock = 0;
#endif
info->start[0] = (ulong)map_physmem(base, info->portwidth, MAP_NOCACHE);
if (flash_detect_cfi(info, &qry)) {
info->vendor = le16_to_cpu(get_unaligned(&qry.p_id));
info->ext_addr = le16_to_cpu(get_unaligned(&qry.p_adr));
num_erase_regions = qry.num_erase_regions;
if (info->ext_addr) {
info->cfi_version = (ushort)flash_read_uchar(info,
info->ext_addr + 3) << 8;
info->cfi_version |= (ushort)flash_read_uchar(info,
info->ext_addr + 4);
}
#ifdef DEBUG
flash_printqry(&qry);
#endif
switch (info->vendor) {
case CFI_CMDSET_INTEL_PROG_REGIONS:
case CFI_CMDSET_INTEL_STANDARD:
case CFI_CMDSET_INTEL_EXTENDED:
cmdset_intel_init(info, &qry);
break;
case CFI_CMDSET_AMD_STANDARD:
case CFI_CMDSET_AMD_EXTENDED:
cmdset_amd_init(info, &qry);
break;
default:
printf("CFI: Unknown command set 0x%x\n",
info->vendor);
/*
* Unfortunately, this means we don't know how
* to get the chip back to Read mode. Might
* as well try an Intel-style reset...
*/
flash_write_cmd(info, 0, 0, FLASH_CMD_RESET);
return 0;
}
/* Do manufacturer-specific fixups */
switch (info->manufacturer_id) {
case 0x0001: /* AMD */
case 0x0037: /* AMIC */
flash_fixup_amd(info, &qry);
break;
case 0x001f:
flash_fixup_atmel(info, &qry);
break;
case 0x0020:
flash_fixup_stm(info, &qry);
break;
case 0x00bf: /* SST */
flash_fixup_sst(info, &qry);
break;
case 0x0089: /* Numonyx */
flash_fixup_num(info, &qry);
break;
}
debug("manufacturer is %d\n", info->vendor);
debug("manufacturer id is 0x%x\n", info->manufacturer_id);
debug("device id is 0x%x\n", info->device_id);
debug("device id2 is 0x%x\n", info->device_id2);
debug("cfi version is 0x%04x\n", info->cfi_version);
size_ratio = info->portwidth / info->chipwidth;
/* if the chip is x8/x16 reduce the ratio by half */
if (info->interface == FLASH_CFI_X8X16 &&
info->chipwidth == FLASH_CFI_BY8) {
size_ratio >>= 1;
}
debug("size_ratio %d port %d bits chip %d bits\n",
size_ratio, info->portwidth << CFI_FLASH_SHIFT_WIDTH,
info->chipwidth << CFI_FLASH_SHIFT_WIDTH);
info->size = 1 << qry.dev_size;
/* multiply the size by the number of chips */
info->size *= size_ratio;
max_size = cfi_flash_bank_size(banknum);
#ifdef CONFIG_CFI_FLASH
if (max_size)
max_size = min((unsigned long)info->addr_size, max_size);
else
max_size = info->addr_size;
#endif
if (max_size && info->size > max_size) {
debug("[truncated from %ldMiB]", info->size >> 20);
info->size = max_size;
}
debug("found %d erase regions\n", num_erase_regions);
sect_cnt = 0;
sector = base;
for (i = 0; i < num_erase_regions; i++) {
if (i > NUM_ERASE_REGIONS) {
printf("%d erase regions found, only %d used\n",
num_erase_regions, NUM_ERASE_REGIONS);
break;
}
tmp = le32_to_cpu(get_unaligned(
&qry.erase_region_info[i]));
debug("erase region %u: 0x%08lx\n", i, tmp);
erase_region_count = (tmp & 0xffff) + 1;
tmp >>= 16;
erase_region_size =
(tmp & 0xffff) ? ((tmp & 0xffff) * 256) : 128;
debug("erase_region_count = %d ", erase_region_count);
debug("erase_region_size = %d\n", erase_region_size);
for (j = 0; j < erase_region_count; j++) {
if (sector - base >= info->size)
break;
if (sect_cnt >= CONFIG_SYS_MAX_FLASH_SECT) {
printf("ERROR: too many flash sectors\n");
break;
}
info->start[sect_cnt] =
(ulong)map_physmem(sector,
info->portwidth,
MAP_NOCACHE);
sector += (erase_region_size * size_ratio);
/*
* Only read protection status from
* supported devices (intel...)
*/
switch (info->vendor) {
case CFI_CMDSET_INTEL_PROG_REGIONS:
case CFI_CMDSET_INTEL_EXTENDED:
case CFI_CMDSET_INTEL_STANDARD:
/*
* Set flash to read-id mode. Otherwise
* reading protected status is not
* guaranteed.
*/
flash_write_cmd(info, sect_cnt, 0,
FLASH_CMD_READ_ID);
info->protect[sect_cnt] =
flash_isset(info, sect_cnt,
FLASH_OFFSET_PROTECT,
FLASH_STATUS_PROTECT);
flash_write_cmd(info, sect_cnt, 0,
FLASH_CMD_RESET);
break;
case CFI_CMDSET_AMD_EXTENDED:
case CFI_CMDSET_AMD_STANDARD:
if (!info->legacy_unlock) {
/* default: not protected */
info->protect[sect_cnt] = 0;
break;
}
/* Read protection (PPB) from sector */
flash_write_cmd(info, 0, 0,
info->cmd_reset);
flash_unlock_seq(info, 0);
flash_write_cmd(info, 0,
info->addr_unlock1,
AMD_CMD_SET_PPB_ENTRY);
info->protect[sect_cnt] =
!flash_isset(info, sect_cnt,
0, 0x01);
flash_write_cmd(info, 0, 0,
info->cmd_reset);
break;
default:
/* default: not protected */
info->protect[sect_cnt] = 0;
}
sect_cnt++;
}
}
info->sector_count = sect_cnt;
info->buffer_size = 1 << le16_to_cpu(qry.max_buf_write_size);
tmp = 1 << qry.block_erase_timeout_typ;
info->erase_blk_tout = tmp *
(1 << qry.block_erase_timeout_max);
tmp = (1 << qry.buf_write_timeout_typ) *
(1 << qry.buf_write_timeout_max);
/* round up when converting to ms */
info->buffer_write_tout = (tmp + 999) / 1000;
tmp = (1 << qry.word_write_timeout_typ) *
(1 << qry.word_write_timeout_max);
/* round up when converting to ms */
info->write_tout = (tmp + 999) / 1000;
info->flash_id = FLASH_MAN_CFI;
if (info->interface == FLASH_CFI_X8X16 &&
info->chipwidth == FLASH_CFI_BY8) {
/* XXX - Need to test on x8/x16 in parallel. */
info->portwidth >>= 1;
}
flash_write_cmd(info, 0, 0, info->cmd_reset);
}
return (info->size);
}
#ifdef CONFIG_FLASH_CFI_MTD
void flash_set_verbose(uint v)
{
flash_verbose = v;
}
#endif
static void cfi_flash_set_config_reg(u32 base, u16 val)
{
#ifdef CONFIG_SYS_CFI_FLASH_CONFIG_REGS
/*
* Only set this config register if really defined
* to a valid value (0xffff is invalid)
*/
if (val == 0xffff)
return;
/*
* Set configuration register. Data is "encrypted" in the 16 lower
* address bits.
*/
flash_write16(FLASH_CMD_SETUP, (void *)(base + (val << 1)));
flash_write16(FLASH_CMD_SET_CR_CONFIRM, (void *)(base + (val << 1)));
/*
* Finally issue reset-command to bring device back to
* read-array mode
*/
flash_write16(FLASH_CMD_RESET, (void *)base);
#endif
}
/*-----------------------------------------------------------------------
*/
static void flash_protect_default(void)
{
#if defined(CONFIG_SYS_FLASH_AUTOPROTECT_LIST)
int i;
struct apl_s {
ulong start;
ulong size;
} apl[] = CONFIG_SYS_FLASH_AUTOPROTECT_LIST;
#endif
/* Monitor protection ON by default */
#if defined(CONFIG_SYS_MONITOR_BASE) && \
(CONFIG_SYS_MONITOR_BASE >= CFG_SYS_FLASH_BASE) && \
(!defined(CONFIG_MONITOR_IS_IN_RAM))
flash_protect(FLAG_PROTECT_SET,
CONFIG_SYS_MONITOR_BASE,
CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1,
flash_get_info(CONFIG_SYS_MONITOR_BASE));
#endif
/* Environment protection ON by default */
#ifdef CONFIG_ENV_IS_IN_FLASH
flash_protect(FLAG_PROTECT_SET,
CONFIG_ENV_ADDR,
CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE - 1,
flash_get_info(CONFIG_ENV_ADDR));
#endif
/* Redundant environment protection ON by default */
#ifdef CONFIG_ENV_ADDR_REDUND
flash_protect(FLAG_PROTECT_SET,
CONFIG_ENV_ADDR_REDUND,
CONFIG_ENV_ADDR_REDUND + CONFIG_ENV_SECT_SIZE - 1,
flash_get_info(CONFIG_ENV_ADDR_REDUND));
#endif
#if defined(CONFIG_SYS_FLASH_AUTOPROTECT_LIST)
for (i = 0; i < ARRAY_SIZE(apl); i++) {
debug("autoprotecting from %08lx to %08lx\n",
apl[i].start, apl[i].start + apl[i].size - 1);
flash_protect(FLAG_PROTECT_SET,
apl[i].start,
apl[i].start + apl[i].size - 1,
flash_get_info(apl[i].start));
}
#endif
}
unsigned long flash_init(void)
{
unsigned long size = 0;
int i;
#ifdef CONFIG_SYS_FLASH_PROTECTION
/* read environment from EEPROM */
char s[64];
env_get_f("unlock", s, sizeof(s));
#endif
#ifdef CONFIG_CFI_FLASH /* for driver model */
cfi_flash_init_dm();
#endif
/* Init: no FLASHes known */
for (i = 0; i < CFI_FLASH_BANKS; ++i) {
flash_info[i].flash_id = FLASH_UNKNOWN;
/* Optionally write flash configuration register */
cfi_flash_set_config_reg(cfi_flash_bank_addr(i),
cfi_flash_config_reg(i));
if (!flash_detect_legacy(cfi_flash_bank_addr(i), i))
flash_get_size(cfi_flash_bank_addr(i), i);
size += flash_info[i].size;
if (flash_info[i].flash_id == FLASH_UNKNOWN) {
#ifndef CONFIG_SYS_FLASH_QUIET_TEST
printf("## Unknown flash on Bank %d ", i + 1);
printf("- Size = 0x%08lx = %ld MB\n",
flash_info[i].size,
flash_info[i].size >> 20);
#endif /* CONFIG_SYS_FLASH_QUIET_TEST */
}
#ifdef CONFIG_SYS_FLASH_PROTECTION
else if (strcmp(s, "yes") == 0) {
/*
* Only the U-Boot image and it's environment
* is protected, all other sectors are
* unprotected (unlocked) if flash hardware
* protection is used (CONFIG_SYS_FLASH_PROTECTION)
* and the environment variable "unlock" is
* set to "yes".
*/
if (flash_info[i].legacy_unlock) {
int k;
/*
* Disable legacy_unlock temporarily,
* since flash_real_protect would
* relock all other sectors again
* otherwise.
*/
flash_info[i].legacy_unlock = 0;
/*
* Legacy unlocking (e.g. Intel J3) ->
* unlock only one sector. This will
* unlock all sectors.
*/
flash_real_protect(&flash_info[i], 0, 0);
flash_info[i].legacy_unlock = 1;
/*
* Manually mark other sectors as
* unlocked (unprotected)
*/
for (k = 1; k < flash_info[i].sector_count; k++)
flash_info[i].protect[k] = 0;
} else {
/*
* No legancy unlocking -> unlock all sectors
*/
flash_protect(FLAG_PROTECT_CLEAR,
flash_info[i].start[0],
flash_info[i].start[0]
+ flash_info[i].size - 1,
&flash_info[i]);
}
}
#endif /* CONFIG_SYS_FLASH_PROTECTION */
}
flash_protect_default();
#ifdef CONFIG_FLASH_CFI_MTD
cfi_mtd_init();
#endif
return (size);
}
#ifdef CONFIG_CFI_FLASH /* for driver model */
static int cfi_flash_probe(struct udevice *dev)
{
fdt_addr_t addr;
fdt_size_t size;
int idx;
for (idx = 0; idx < CFI_MAX_FLASH_BANKS; idx++) {
addr = dev_read_addr_size_index(dev, idx, &size);
if (addr == FDT_ADDR_T_NONE)
break;
flash_info[cfi_flash_num_flash_banks].dev = dev;
flash_info[cfi_flash_num_flash_banks].base = addr;
flash_info[cfi_flash_num_flash_banks].addr_size = size;
cfi_flash_num_flash_banks++;
}
gd->bd->bi_flashstart = flash_info[0].base;
return 0;
}
static const struct udevice_id cfi_flash_ids[] = {
{ .compatible = "cfi-flash" },
{ .compatible = "jedec-flash" },
{}
};
U_BOOT_DRIVER(cfi_flash) = {
.name = "cfi_flash",
.id = UCLASS_MTD,
.of_match = cfi_flash_ids,
.probe = cfi_flash_probe,
};
#endif /* CONFIG_CFI_FLASH */