include/configs/ls1088ardb.h - filogic/uboot - Gitiles

 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2017, 2020-2021 NXP
  */

 #ifndef __LS1088A_RDB_H
 #define __LS1088A_RDB_H

 #include "ls1088a_common.h"

 #if defined(CONFIG_TFABOOT) || \
 	defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
 #ifndef CONFIG_SPL_BUILD
 #define CONFIG_QIXIS_I2C_ACCESS
 #endif
 #define SYS_NO_FLASH
 #endif

 #define CONFIG_SYS_CLK_FREQ		100000000
 #define CONFIG_DDR_CLK_FREQ		100000000
 #define COUNTER_FREQUENCY_REAL		25000000	/* 25MHz */
 #define COUNTER_FREQUENCY		25000000	/* 25MHz */

 #define CONFIG_DDR_SPD
 #ifdef CONFIG_EMU
 #define CONFIG_SYS_FSL_DDR_EMU
 #define CONFIG_SYS_MXC_I2C1_SPEED	40000000
 #define CONFIG_SYS_MXC_I2C2_SPEED	40000000
 #else
 #define CONFIG_DDR_ECC
 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
 #endif
 #define SPD_EEPROM_ADDRESS	0x51
 #define CONFIG_SYS_SPD_BUS_NUM	0	/* SPD on I2C bus 0 */
 #define CONFIG_DIMM_SLOTS_PER_CTLR	1


 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
 #define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
 #define CONFIG_SYS_NOR_AMASK		IFC_AMASK(128 * 1024 * 1024)
 #define CONFIG_SYS_NOR_AMASK_EARLY	IFC_AMASK(64 * 1024 * 1024)

 #define CONFIG_SYS_NOR0_CSPR					\
 	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS)		| \
 	CSPR_PORT_SIZE_16					| \
 	CSPR_MSEL_NOR						| \
 	CSPR_V)
 #define CONFIG_SYS_NOR0_CSPR_EARLY				\
 	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY)	| \
 	CSPR_PORT_SIZE_16					| \
 	CSPR_MSEL_NOR						| \
 	CSPR_V)
 #define CONFIG_SYS_NOR_CSOR	CSOR_NOR_ADM_SHIFT(6)
 #define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x1) | \
 				FTIM0_NOR_TEADC(0x1) | \
 				FTIM0_NOR_TEAHC(0x1))
 #define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x1) | \
 				FTIM1_NOR_TRAD_NOR(0x1))
 #define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x0) | \
 				FTIM2_NOR_TCH(0x0) | \
 				FTIM2_NOR_TWP(0x1))
 #define CONFIG_SYS_NOR_FTIM3	0x04000000
 #define CONFIG_SYS_IFC_CCR	0x01000000

 #ifndef SYS_NO_FLASH
 #define CONFIG_SYS_FLASH_QUIET_TEST
 #define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */

 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */

 #define CONFIG_SYS_FLASH_EMPTY_INFO
 #define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
 #endif
 #endif

 #ifndef SPL_NO_IFC
 #define CONFIG_NAND_FSL_IFC
 #endif

 #define CONFIG_SYS_NAND_MAX_ECCPOS	256
 #define CONFIG_SYS_NAND_MAX_OOBFREE	2

 #define CONFIG_SYS_NAND_CSPR_EXT	(0x0)
 #define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 				| CSPR_MSEL_NAND	/* MSEL = NAND */ \
 				| CSPR_V)
 #define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64 * 1024)

 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
 				| CSOR_NAND_RAL_3	/* RAL = 3Byes */ \
 				| CSOR_NAND_PGS_2K	/* Page Size = 2K */ \
 				| CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
 				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/

 #define CONFIG_SYS_NAND_ONFI_DETECTION

 /* ONFI NAND Flash mode0 Timing Params */
 #define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \
 					FTIM0_NAND_TWP(0x18)   | \
 					FTIM0_NAND_TWCHT(0x07) | \
 					FTIM0_NAND_TWH(0x0a))
 #define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
 					FTIM1_NAND_TWBE(0x39)  | \
 					FTIM1_NAND_TRR(0x0e)   | \
 					FTIM1_NAND_TRP(0x18))
 #define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x0f) | \
 					FTIM2_NAND_TREH(0x0a) | \
 					FTIM2_NAND_TWHRE(0x1e))
 #define CONFIG_SYS_NAND_FTIM3		0x0

 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
 #define CONFIG_MTD_NAND_VERIFY_WRITE

 #define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)

 #ifndef SPL_NO_QIXIS
 #define CONFIG_FSL_QIXIS
 #endif

 #define CONFIG_SYS_I2C_FPGA_ADDR	0x66
 #define QIXIS_BRDCFG4_OFFSET            0x54
 #define QIXIS_LBMAP_SWITCH		2
 #define QIXIS_QMAP_MASK			0xe0
 #define QIXIS_QMAP_SHIFT		5
 #define QIXIS_LBMAP_MASK		0x1f
 #define QIXIS_LBMAP_SHIFT		5
 #define QIXIS_LBMAP_DFLTBANK		0x00
 #define QIXIS_LBMAP_ALTBANK		0x20
 #define QIXIS_LBMAP_SD			0x00
 #define QIXIS_LBMAP_EMMC		0x00
 #define QIXIS_LBMAP_SD_QSPI		0x00
 #define QIXIS_LBMAP_QSPI		0x00
 #define QIXIS_RCW_SRC_SD		0x40
 #define QIXIS_RCW_SRC_EMMC		0x41
 #define QIXIS_RCW_SRC_QSPI		0x62
 #define QIXIS_RST_CTL_RESET		0x31
 #define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
 #define QIXIS_RCFG_CTL_RECONFIG_START	0x21
 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
 #define	QIXIS_RST_FORCE_MEM		0x01

 #define CONFIG_SYS_FPGA_CSPR_EXT	(0x0)
 #define CONFIG_SYS_FPGA_CSPR		(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
 					| CSPR_PORT_SIZE_8 \
 					| CSPR_MSEL_GPCM \
 					| CSPR_V)
 #define SYS_FPGA_CSPR_FINAL	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
 					| CSPR_PORT_SIZE_8 \
 					| CSPR_MSEL_GPCM \
 					| CSPR_V)

 #define CONFIG_SYS_FPGA_AMASK		IFC_AMASK(64*1024)
 #define CONFIG_SYS_FPGA_CSOR		CSOR_GPCM_ADM_SHIFT(0)
 /* QIXIS Timing parameters*/
 #define SYS_FPGA_CS_FTIM0	(FTIM0_GPCM_TACSE(0x0e) | \
 					FTIM0_GPCM_TEADC(0x0e) | \
 					FTIM0_GPCM_TEAHC(0x0e))
 #define SYS_FPGA_CS_FTIM1	(FTIM1_GPCM_TACO(0xff) | \
 					FTIM1_GPCM_TRAD(0x3f))
 #define SYS_FPGA_CS_FTIM2	(FTIM2_GPCM_TCS(0xf) | \
 					FTIM2_GPCM_TCH(0xf) | \
 					FTIM2_GPCM_TWP(0x3E))
 #define SYS_FPGA_CS_FTIM3	0x0

 #if defined(CONFIG_TFABOOT) || \
 	defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_FPGA_CSPR_EXT
 #define CONFIG_SYS_CSPR2		CONFIG_SYS_FPGA_CSPR
 #define CONFIG_SYS_CSPR2_FINAL		SYS_FPGA_CSPR_FINAL
 #define CONFIG_SYS_AMASK2		CONFIG_SYS_FPGA_AMASK
 #define CONFIG_SYS_CSOR2		CONFIG_SYS_FPGA_CSOR
 #define CONFIG_SYS_CS2_FTIM0		SYS_FPGA_CS_FTIM0
 #define CONFIG_SYS_CS2_FTIM1		SYS_FPGA_CS_FTIM1
 #define CONFIG_SYS_CS2_FTIM2		SYS_FPGA_CS_FTIM2
 #define CONFIG_SYS_CS2_FTIM3		SYS_FPGA_CS_FTIM3
 #else
 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR_EARLY
 #define CONFIG_SYS_CSPR0_FINAL		CONFIG_SYS_NOR0_CSPR
 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
 #endif

 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000

 #define I2C_MUX_CH_VOL_MONITOR         0xA
 /* Voltage monitor on channel 2*/
 #define I2C_VOL_MONITOR_ADDR           0x63
 #define I2C_VOL_MONITOR_BUS_V_OFFSET   0x2
 #define I2C_VOL_MONITOR_BUS_V_OVF      0x1
 #define I2C_VOL_MONITOR_BUS_V_SHIFT    3
 #define I2C_SVDD_MONITOR_ADDR		0x4F

 #define CONFIG_VID_FLS_ENV              "ls1088ardb_vdd_mv"
 #define CONFIG_VID

 /* The lowest and highest voltage allowed for LS1088ARDB */
 #define VDD_MV_MIN			819
 #define VDD_MV_MAX			1212

 #define CONFIG_VOL_MONITOR_LTC3882_SET
 #define CONFIG_VOL_MONITOR_LTC3882_READ

 #define PWM_CHANNEL0                    0x0

 /*
  * I2C bus multiplexer
  */
 #define I2C_MUX_PCA_ADDR_PRI		0x77
 #define I2C_MUX_PCA_ADDR_SEC		0x76 /* Secondary multiplexer */
 #define I2C_RETIMER_ADDR		0x18
 #define I2C_MUX_CH_DEFAULT		0x8
 #define I2C_MUX_CH5			0xD

 #ifndef SPL_NO_RTC
 /*
 * RTC configuration
 */
 #define RTC
 #define CONFIG_SYS_I2C_RTC_ADDR         0x51  /* Channel 3*/
 #endif

 /* EEPROM */
 #define CONFIG_SYS_I2C_EEPROM_NXID
 #define CONFIG_SYS_EEPROM_BUS_NUM		0

 #ifdef CONFIG_SPL_BUILD
 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
 #else
 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
 #endif

 #define CONFIG_FSL_MEMAC

 #ifndef SPL_NO_ENV
 /* Initial environment variables */
 #ifdef CONFIG_TFABOOT
 #define QSPI_MC_INIT_CMD				\
 	"sf probe 0:0;sf read 0x80a00000 0xA00000 0x200000;"	\
 	"sf read 0x80e00000 0xE00000 0x100000;"				\
 	"env exists secureboot && "			\
 	"sf read 0x80640000 0x640000 0x40000 && "	\
 	"sf read 0x80680000 0x680000 0x40000 && "	\
 	"esbc_validate 0x80640000 && "			\
 	"esbc_validate 0x80680000 ;"			\
 	"fsl_mc start mc 0x80a00000 0x80e00000\0"
 #define SD_MC_INIT_CMD				\
 	"mmcinfo;mmc read 0x80a00000 0x5000 0x1000;"		\
 	"mmc read 0x80e00000 0x7000 0x800;"				\
 	"env exists secureboot && "			\
 	"mmc read 0x80640000 0x3200 0x20 && "		\
 	"mmc read 0x80680000 0x3400 0x20 && "		\
 	"esbc_validate 0x80640000 && "			\
 	"esbc_validate 0x80680000 ;"			\
 	"fsl_mc start mc 0x80a00000 0x80e00000\0"
 #else
 #if defined(CONFIG_QSPI_BOOT)
 #define MC_INIT_CMD				\
 	"mcinitcmd=sf probe 0:0;sf read 0x80a00000 0xA00000 0x200000;"	\
 	"sf read 0x80e00000 0xE00000 0x100000;"				\
 	"env exists secureboot && "			\
 	"sf read 0x80640000 0x640000 0x40000 && "	\
 	"sf read 0x80680000 0x680000 0x40000 && "	\
 	"esbc_validate 0x80640000 && "			\
 	"esbc_validate 0x80680000 ;"			\
 	"fsl_mc start mc 0x80a00000 0x80e00000\0"	\
 	"mcmemsize=0x70000000\0"
 #elif defined(CONFIG_SD_BOOT)
 #define MC_INIT_CMD				\
 	"mcinitcmd=mmcinfo;mmc read 0x80a00000 0x5000 0x1000;"		\
 	"mmc read 0x80e00000 0x7000 0x800;"				\
 	"env exists secureboot && "			\
 	"mmc read 0x80640000 0x3200 0x20 && "		\
 	"mmc read 0x80680000 0x3400 0x20 && "		\
 	"esbc_validate 0x80640000 && "			\
 	"esbc_validate 0x80680000 ;"			\
 	"fsl_mc start mc 0x80a00000 0x80e00000\0"	\
 	"mcmemsize=0x70000000\0"
 #endif
 #endif /* CONFIG_TFABOOT */

 #undef CONFIG_EXTRA_ENV_SETTINGS
 #ifdef CONFIG_TFABOOT
 #define CONFIG_EXTRA_ENV_SETTINGS		\
 	"BOARD=ls1088ardb\0"			\
 	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
 	"ramdisk_addr=0x800000\0"		\
 	"ramdisk_size=0x2000000\0"		\
 	"fdt_high=0xa0000000\0"			\
 	"initrd_high=0xffffffffffffffff\0"	\
 	"fdt_addr=0x64f00000\0"			\
 	"kernel_addr=0x1000000\0"		\
 	"kernel_addr_sd=0x8000\0"		\
 	"kernelhdr_addr_sd=0x3000\0"		\
 	"kernel_start=0x580100000\0"		\
 	"kernelheader_start=0x580600000\0"	\
 	"scriptaddr=0x80000000\0"		\
 	"scripthdraddr=0x80080000\0"		\
 	"fdtheader_addr_r=0x80100000\0"		\
 	"kernelheader_addr=0x600000\0"		\
 	"kernelheader_addr_r=0x80200000\0"	\
 	"kernel_addr_r=0x81000000\0"		\
 	"kernelheader_size=0x40000\0"		\
 	"fdt_addr_r=0x90000000\0"		\
 	"load_addr=0xa0000000\0"		\
 	"kernel_size=0x2800000\0"		\
 	"kernel_size_sd=0x14000\0"		\
 	"kernelhdr_size_sd=0x20\0"		\
 	QSPI_MC_INIT_CMD			\
 	"mcmemsize=0x70000000\0"		\
 	BOOTENV					\
 	"boot_scripts=ls1088ardb_boot.scr\0"	\
 	"boot_script_hdr=hdr_ls1088ardb_bs.out\0"	\
 	"scan_dev_for_boot_part="		\
 		"part list ${devtype} ${devnum} devplist; "	\
 		"env exists devplist || setenv devplist 1; "	\
 		"for distro_bootpart in ${devplist}; do "	\
 			"if fstype ${devtype} "			\
 				"${devnum}:${distro_bootpart} "	\
 				"bootfstype; then "		\
 				"run scan_dev_for_boot; "	\
 			"fi; "					\
 		"done\0"					\
 	"boot_a_script="					\
 		"load ${devtype} ${devnum}:${distro_bootpart} " \
 		"${scriptaddr} ${prefix}${script}; "		\
 	"env exists secureboot && load ${devtype} "		\
 		"${devnum}:${distro_bootpart} "			\
 		"${scripthdraddr} ${prefix}${boot_script_hdr}; "\
 		"env exists secureboot "			\
 		"&& esbc_validate ${scripthdraddr};"		\
 		"source ${scriptaddr}\0"			\
 	"installer=load mmc 0:2 $load_addr "			\
 		"/flex_installer_arm64.itb; "			\
 		"env exists mcinitcmd && run mcinitcmd && "	\
 		"mmc read 0x80001000 0x6800 0x800;"		\
 		"fsl_mc lazyapply dpl 0x80001000;"			\
 		"bootm $load_addr#ls1088ardb\0"			\
 	"qspi_bootcmd=echo Trying load from qspi..;"		\
 		"sf probe && sf read $load_addr "		\
 		"$kernel_addr $kernel_size ; env exists secureboot "	\
 		"&& sf read $kernelheader_addr_r $kernelheader_addr "	\
 		"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
 		"bootm $load_addr#$BOARD\0"			\
 		"sd_bootcmd=echo Trying load from sd card..;"		\
 		"mmcinfo; mmc read $load_addr "			\
 		"$kernel_addr_sd $kernel_size_sd ;"		\
 		"env exists secureboot && mmc read $kernelheader_addr_r "\
 		"$kernelhdr_addr_sd $kernelhdr_size_sd "	\
 		" && esbc_validate ${kernelheader_addr_r};"	\
 		"bootm $load_addr#$BOARD\0"
 #else
 #define CONFIG_EXTRA_ENV_SETTINGS		\
 	"BOARD=ls1088ardb\0"			\
 	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
 	"ramdisk_addr=0x800000\0"		\
 	"ramdisk_size=0x2000000\0"		\
 	"fdt_high=0xa0000000\0"			\
 	"initrd_high=0xffffffffffffffff\0"	\
 	"fdt_addr=0x64f00000\0"			\
 	"kernel_addr=0x1000000\0"		\
 	"kernel_addr_sd=0x8000\0"		\
 	"kernelhdr_addr_sd=0x3000\0"		\
 	"kernel_start=0x580100000\0"		\
 	"kernelheader_start=0x580800000\0"	\
 	"scriptaddr=0x80000000\0"		\
 	"scripthdraddr=0x80080000\0"		\
 	"fdtheader_addr_r=0x80100000\0"		\
 	"kernelheader_addr=0x600000\0"		\
 	"kernelheader_addr_r=0x80200000\0"	\
 	"kernel_addr_r=0x81000000\0"		\
 	"kernelheader_size=0x40000\0"		\
 	"fdt_addr_r=0x90000000\0"		\
 	"load_addr=0xa0000000\0"		\
 	"kernel_size=0x2800000\0"		\
 	"kernel_size_sd=0x14000\0"		\
 	"kernelhdr_size_sd=0x20\0"		\
 	MC_INIT_CMD				\
 	BOOTENV					\
 	"boot_scripts=ls1088ardb_boot.scr\0"	\
 	"boot_script_hdr=hdr_ls1088ardb_bs.out\0"	\
 	"scan_dev_for_boot_part="		\
 		"part list ${devtype} ${devnum} devplist; "	\
 		"env exists devplist || setenv devplist 1; "	\
 		"for distro_bootpart in ${devplist}; do "	\
 			"if fstype ${devtype} "			\
 				"${devnum}:${distro_bootpart} "	\
 				"bootfstype; then "		\
 				"run scan_dev_for_boot; "	\
 			"fi; "					\
 		"done\0"					\
 	"boot_a_script="					\
 		"load ${devtype} ${devnum}:${distro_bootpart} " \
 		"${scriptaddr} ${prefix}${script}; "		\
 	"env exists secureboot && load ${devtype} "		\
 		"${devnum}:${distro_bootpart} "			\
 		"${scripthdraddr} ${prefix}${boot_script_hdr} " \
 		"&& esbc_validate ${scripthdraddr};"		\
 		"source ${scriptaddr}\0"			\
 	"installer=load mmc 0:2 $load_addr "			\
 		"/flex_installer_arm64.itb; "			\
 		"env exists mcinitcmd && run mcinitcmd && "	\
 		"mmc read 0x80001000 0x6800 0x800;"		\
 		"fsl_mc lazyapply dpl 0x80001000;"			\
 		"bootm $load_addr#ls1088ardb\0"			\
 	"qspi_bootcmd=echo Trying load from qspi..;"		\
 		"sf probe && sf read $load_addr "		\
 		"$kernel_addr $kernel_size ; env exists secureboot "	\
 		"&& sf read $kernelheader_addr_r $kernelheader_addr "	\
 		"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
 		"bootm $load_addr#$BOARD\0"			\
 		"sd_bootcmd=echo Trying load from sd card..;"		\
 		"mmcinfo; mmc read $load_addr "			\
 		"$kernel_addr_sd $kernel_size_sd ;"		\
 		"env exists secureboot && mmc read $kernelheader_addr_r "\
 		"$kernelhdr_addr_sd $kernelhdr_size_sd "	\
 		" && esbc_validate ${kernelheader_addr_r};"	\
 		"bootm $load_addr#$BOARD\0"
 #endif /* CONFIG_TFABOOT */

 #undef CONFIG_BOOTCOMMAND
 #ifdef CONFIG_TFABOOT
 #define QSPI_NOR_BOOTCOMMAND					\
 	"sf read 0x80001000 0xd00000 0x100000;"		\
 		"env exists mcinitcmd && env exists secureboot "	\
 		" && sf read 0x806C0000 0x6C0000 0x100000 "	\
 		"&& esbc_validate 0x806C0000;env exists mcinitcmd "	\
 		"&& fsl_mc lazyapply dpl 0x80001000;"		\
 		"run distro_bootcmd;run qspi_bootcmd;"		\
 		"env exists secureboot && esbc_halt;"
 #define SD_BOOTCOMMAND						\
 		"env exists mcinitcmd && mmcinfo; "		\
 		"mmc read 0x80001000 0x6800 0x800; "		\
 		"env exists mcinitcmd && env exists secureboot "	\
 		" && mmc read 0x806C0000 0x3600 0x20 "		\
 		"&& esbc_validate 0x806C0000;env exists mcinitcmd "	\
 		"&& fsl_mc lazyapply dpl 0x80001000;"		\
 		"run distro_bootcmd;run sd_bootcmd;"		\
 		"env exists secureboot && esbc_halt;"
 #else
 #if defined(CONFIG_QSPI_BOOT)
 /* Try to boot an on-QSPI kernel first, then do normal distro boot */
 #define CONFIG_BOOTCOMMAND                                      \
 		"sf read 0x80001000 0xd00000 0x100000;"		\
 		"env exists mcinitcmd && env exists secureboot "	\
 		" && sf read 0x806C0000 0x6C0000 0x100000 "	\
 		"&& esbc_validate 0x806C0000;env exists mcinitcmd "	\
 		"&& fsl_mc lazyapply dpl 0x80001000;"		\
 		"run distro_bootcmd;run qspi_bootcmd;"		\
 		"env exists secureboot && esbc_halt;"

 /* Try to boot an on-SD kernel first, then do normal distro boot */
 #elif defined(CONFIG_SD_BOOT)
 #define CONFIG_BOOTCOMMAND                                      \
 		"env exists mcinitcmd && mmcinfo; "		\
 		"mmc read 0x80001000 0x6800 0x800; "		\
 		"env exists mcinitcmd && env exists secureboot "	\
 		" && mmc read 0x806C0000 0x3600 0x20 "		\
 		"&& esbc_validate 0x806C0000;env exists mcinitcmd "	\
 		"&& fsl_mc lazyapply dpl 0x80001000;"		\
 		"run distro_bootcmd;run sd_bootcmd;"		\
 		"env exists secureboot && esbc_halt;"
 #endif
 #endif /* CONFIG_TFABOOT */

 /* MAC/PHY configuration */
 #ifdef CONFIG_FSL_MC_ENET
 #define AQ_PHY_ADDR1			0x00
 #define AQR105_IRQ_MASK			0x00000004

 #define QSGMII1_PORT1_PHY_ADDR		0x0c
 #define QSGMII1_PORT2_PHY_ADDR		0x0d
 #define QSGMII1_PORT3_PHY_ADDR		0x0e
 #define QSGMII1_PORT4_PHY_ADDR		0x0f
 #define QSGMII2_PORT1_PHY_ADDR		0x1c
 #define QSGMII2_PORT2_PHY_ADDR		0x1d
 #define QSGMII2_PORT3_PHY_ADDR		0x1e
 #define QSGMII2_PORT4_PHY_ADDR		0x1f

 #define CONFIG_ETHPRIME		"DPMAC1@xgmii"
 #define CONFIG_PHY_GIGE
 #endif
 #endif

 #ifndef SPL_NO_ENV

 #define BOOT_TARGET_DEVICES(func) \
 	func(MMC, mmc, 0) \
 	func(USB, usb, 0) \
 	func(SCSI, scsi, 0) \
 	func(DHCP, dhcp, na)
 #include <config_distro_bootcmd.h>
 #endif

 #include <asm/fsl_secure_boot.h>

 #endif /* __LS1088A_RDB_H */
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* Copyright 2017, 2020-2021 NXP
	*/

	#ifndef __LS1088A_RDB_H
	#define __LS1088A_RDB_H

	#include "ls1088a_common.h"

	#if defined(CONFIG_TFABOOT) \|\| \
	defined(CONFIG_QSPI_BOOT) \|\| defined(CONFIG_SD_BOOT_QSPI)
	#ifndef CONFIG_SPL_BUILD
	#define CONFIG_QIXIS_I2C_ACCESS
	#endif
	#define SYS_NO_FLASH
	#endif

	#define CONFIG_SYS_CLK_FREQ 100000000
	#define CONFIG_DDR_CLK_FREQ 100000000
	#define COUNTER_FREQUENCY_REAL 25000000 /* 25MHz */
	#define COUNTER_FREQUENCY 25000000 /* 25MHz */

	#define CONFIG_DDR_SPD
	#ifdef CONFIG_EMU
	#define CONFIG_SYS_FSL_DDR_EMU
	#define CONFIG_SYS_MXC_I2C1_SPEED 40000000
	#define CONFIG_SYS_MXC_I2C2_SPEED 40000000
	#else
	#define CONFIG_DDR_ECC
	#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
	#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
	#endif
	#define SPD_EEPROM_ADDRESS 0x51
	#define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */
	#define CONFIG_DIMM_SLOTS_PER_CTLR 1


	#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
	#define CONFIG_SYS_NOR0_CSPR_EXT (0x0)
	#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128 * 1024 * 1024)
	#define CONFIG_SYS_NOR_AMASK_EARLY IFC_AMASK(64 * 1024 * 1024)

	#define CONFIG_SYS_NOR0_CSPR \
	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \| \
	CSPR_PORT_SIZE_16 \| \
	CSPR_MSEL_NOR \| \
	CSPR_V)
	#define CONFIG_SYS_NOR0_CSPR_EARLY \
	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY) \| \
	CSPR_PORT_SIZE_16 \| \
	CSPR_MSEL_NOR \| \
	CSPR_V)
	#define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(6)
	#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x1) \| \
	FTIM0_NOR_TEADC(0x1) \| \
	FTIM0_NOR_TEAHC(0x1))
	#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x1) \| \
	FTIM1_NOR_TRAD_NOR(0x1))
	#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x0) \| \
	FTIM2_NOR_TCH(0x0) \| \
	FTIM2_NOR_TWP(0x1))
	#define CONFIG_SYS_NOR_FTIM3 0x04000000
	#define CONFIG_SYS_IFC_CCR 0x01000000

	#ifndef SYS_NO_FLASH
	#define CONFIG_SYS_FLASH_QUIET_TEST
	#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */

	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
	#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */

	#define CONFIG_SYS_FLASH_EMPTY_INFO
	#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
	#endif
	#endif

	#ifndef SPL_NO_IFC
	#define CONFIG_NAND_FSL_IFC
	#endif

	#define CONFIG_SYS_NAND_MAX_ECCPOS 256
	#define CONFIG_SYS_NAND_MAX_OOBFREE 2

	#define CONFIG_SYS_NAND_CSPR_EXT (0x0)
	#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
	\| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
	\| CSPR_MSEL_NAND /* MSEL = NAND */ \
	\| CSPR_V)
	#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024)

	#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
	\| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
	\| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
	\| CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
	\| CSOR_NAND_PGS_2K /* Page Size = 2K */ \
	\| CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
	\| CSOR_NAND_PB(64)) /Pages Per Block = 64/

	#define CONFIG_SYS_NAND_ONFI_DETECTION

	/* ONFI NAND Flash mode0 Timing Params */
	#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) \| \
	FTIM0_NAND_TWP(0x18) \| \
	FTIM0_NAND_TWCHT(0x07) \| \
	FTIM0_NAND_TWH(0x0a))
	#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) \| \
	FTIM1_NAND_TWBE(0x39) \| \
	FTIM1_NAND_TRR(0x0e) \| \
	FTIM1_NAND_TRP(0x18))
	#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) \| \
	FTIM2_NAND_TREH(0x0a) \| \
	FTIM2_NAND_TWHRE(0x1e))
	#define CONFIG_SYS_NAND_FTIM3 0x0

	#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	#define CONFIG_MTD_NAND_VERIFY_WRITE

	#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)

	#ifndef SPL_NO_QIXIS
	#define CONFIG_FSL_QIXIS
	#endif

	#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
	#define QIXIS_BRDCFG4_OFFSET 0x54
	#define QIXIS_LBMAP_SWITCH 2
	#define QIXIS_QMAP_MASK 0xe0
	#define QIXIS_QMAP_SHIFT 5
	#define QIXIS_LBMAP_MASK 0x1f
	#define QIXIS_LBMAP_SHIFT 5
	#define QIXIS_LBMAP_DFLTBANK 0x00
	#define QIXIS_LBMAP_ALTBANK 0x20
	#define QIXIS_LBMAP_SD 0x00
	#define QIXIS_LBMAP_EMMC 0x00
	#define QIXIS_LBMAP_SD_QSPI 0x00
	#define QIXIS_LBMAP_QSPI 0x00
	#define QIXIS_RCW_SRC_SD 0x40
	#define QIXIS_RCW_SRC_EMMC 0x41
	#define QIXIS_RCW_SRC_QSPI 0x62
	#define QIXIS_RST_CTL_RESET 0x31
	#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
	#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
	#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
	#define QIXIS_RST_FORCE_MEM 0x01

	#define CONFIG_SYS_FPGA_CSPR_EXT (0x0)
	#define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
	\| CSPR_PORT_SIZE_8 \
	\| CSPR_MSEL_GPCM \
	\| CSPR_V)
	#define SYS_FPGA_CSPR_FINAL (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
	\| CSPR_PORT_SIZE_8 \
	\| CSPR_MSEL_GPCM \
	\| CSPR_V)

	#define CONFIG_SYS_FPGA_AMASK IFC_AMASK(64*1024)
	#define CONFIG_SYS_FPGA_CSOR CSOR_GPCM_ADM_SHIFT(0)
	/* QIXIS Timing parameters*/
	#define SYS_FPGA_CS_FTIM0 (FTIM0_GPCM_TACSE(0x0e) \| \
	FTIM0_GPCM_TEADC(0x0e) \| \
	FTIM0_GPCM_TEAHC(0x0e))
	#define SYS_FPGA_CS_FTIM1 (FTIM1_GPCM_TACO(0xff) \| \
	FTIM1_GPCM_TRAD(0x3f))
	#define SYS_FPGA_CS_FTIM2 (FTIM2_GPCM_TCS(0xf) \| \
	FTIM2_GPCM_TCH(0xf) \| \
	FTIM2_GPCM_TWP(0x3E))
	#define SYS_FPGA_CS_FTIM3 0x0

	#if defined(CONFIG_TFABOOT) \|\| \
	defined(CONFIG_QSPI_BOOT) \|\| defined(CONFIG_SD_BOOT_QSPI)
	#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
	#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
	#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
	#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
	#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
	#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
	#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
	#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
	#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_FPGA_CSPR_EXT
	#define CONFIG_SYS_CSPR2 CONFIG_SYS_FPGA_CSPR
	#define CONFIG_SYS_CSPR2_FINAL SYS_FPGA_CSPR_FINAL
	#define CONFIG_SYS_AMASK2 CONFIG_SYS_FPGA_AMASK
	#define CONFIG_SYS_CSOR2 CONFIG_SYS_FPGA_CSOR
	#define CONFIG_SYS_CS2_FTIM0 SYS_FPGA_CS_FTIM0
	#define CONFIG_SYS_CS2_FTIM1 SYS_FPGA_CS_FTIM1
	#define CONFIG_SYS_CS2_FTIM2 SYS_FPGA_CS_FTIM2
	#define CONFIG_SYS_CS2_FTIM3 SYS_FPGA_CS_FTIM3
	#else
	#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
	#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY
	#define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR
	#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
	#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
	#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
	#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
	#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
	#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
	#endif

	#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000

	#define I2C_MUX_CH_VOL_MONITOR 0xA
	/* Voltage monitor on channel 2*/
	#define I2C_VOL_MONITOR_ADDR 0x63
	#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
	#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
	#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
	#define I2C_SVDD_MONITOR_ADDR 0x4F

	#define CONFIG_VID_FLS_ENV "ls1088ardb_vdd_mv"
	#define CONFIG_VID

	/* The lowest and highest voltage allowed for LS1088ARDB */
	#define VDD_MV_MIN 819
	#define VDD_MV_MAX 1212

	#define CONFIG_VOL_MONITOR_LTC3882_SET
	#define CONFIG_VOL_MONITOR_LTC3882_READ

	#define PWM_CHANNEL0 0x0

	/*
	* I2C bus multiplexer
	*/
	#define I2C_MUX_PCA_ADDR_PRI 0x77
	#define I2C_MUX_PCA_ADDR_SEC 0x76 /* Secondary multiplexer */
	#define I2C_RETIMER_ADDR 0x18
	#define I2C_MUX_CH_DEFAULT 0x8
	#define I2C_MUX_CH5 0xD

	#ifndef SPL_NO_RTC
	/*
	* RTC configuration
	*/
	#define RTC
	#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/
	#endif

	/* EEPROM */
	#define CONFIG_SYS_I2C_EEPROM_NXID
	#define CONFIG_SYS_EEPROM_BUS_NUM 0

	#ifdef CONFIG_SPL_BUILD
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
	#else
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
	#endif

	#define CONFIG_FSL_MEMAC

	#ifndef SPL_NO_ENV
	/* Initial environment variables */
	#ifdef CONFIG_TFABOOT
	#define QSPI_MC_INIT_CMD \
	"sf probe 0:0;sf read 0x80a00000 0xA00000 0x200000;" \
	"sf read 0x80e00000 0xE00000 0x100000;" \
	"env exists secureboot && " \
	"sf read 0x80640000 0x640000 0x40000 && " \
	"sf read 0x80680000 0x680000 0x40000 && " \
	"esbc_validate 0x80640000 && " \
	"esbc_validate 0x80680000 ;" \
	"fsl_mc start mc 0x80a00000 0x80e00000\0"
	#define SD_MC_INIT_CMD \
	"mmcinfo;mmc read 0x80a00000 0x5000 0x1000;" \
	"mmc read 0x80e00000 0x7000 0x800;" \
	"env exists secureboot && " \
	"mmc read 0x80640000 0x3200 0x20 && " \
	"mmc read 0x80680000 0x3400 0x20 && " \
	"esbc_validate 0x80640000 && " \
	"esbc_validate 0x80680000 ;" \
	"fsl_mc start mc 0x80a00000 0x80e00000\0"
	#else
	#if defined(CONFIG_QSPI_BOOT)
	#define MC_INIT_CMD \
	"mcinitcmd=sf probe 0:0;sf read 0x80a00000 0xA00000 0x200000;" \
	"sf read 0x80e00000 0xE00000 0x100000;" \
	"env exists secureboot && " \
	"sf read 0x80640000 0x640000 0x40000 && " \
	"sf read 0x80680000 0x680000 0x40000 && " \
	"esbc_validate 0x80640000 && " \
	"esbc_validate 0x80680000 ;" \
	"fsl_mc start mc 0x80a00000 0x80e00000\0" \
	"mcmemsize=0x70000000\0"
	#elif defined(CONFIG_SD_BOOT)
	#define MC_INIT_CMD \
	"mcinitcmd=mmcinfo;mmc read 0x80a00000 0x5000 0x1000;" \
	"mmc read 0x80e00000 0x7000 0x800;" \
	"env exists secureboot && " \
	"mmc read 0x80640000 0x3200 0x20 && " \
	"mmc read 0x80680000 0x3400 0x20 && " \
	"esbc_validate 0x80640000 && " \
	"esbc_validate 0x80680000 ;" \
	"fsl_mc start mc 0x80a00000 0x80e00000\0" \
	"mcmemsize=0x70000000\0"
	#endif
	#endif /* CONFIG_TFABOOT */

	#undef CONFIG_EXTRA_ENV_SETTINGS
	#ifdef CONFIG_TFABOOT
	#define CONFIG_EXTRA_ENV_SETTINGS \
	"BOARD=ls1088ardb\0" \
	"hwconfig=fsl_ddr:bank_intlv=auto\0" \
	"ramdisk_addr=0x800000\0" \
	"ramdisk_size=0x2000000\0" \
	"fdt_high=0xa0000000\0" \
	"initrd_high=0xffffffffffffffff\0" \
	"fdt_addr=0x64f00000\0" \
	"kernel_addr=0x1000000\0" \
	"kernel_addr_sd=0x8000\0" \
	"kernelhdr_addr_sd=0x3000\0" \
	"kernel_start=0x580100000\0" \
	"kernelheader_start=0x580600000\0" \
	"scriptaddr=0x80000000\0" \
	"scripthdraddr=0x80080000\0" \
	"fdtheader_addr_r=0x80100000\0" \
	"kernelheader_addr=0x600000\0" \
	"kernelheader_addr_r=0x80200000\0" \
	"kernel_addr_r=0x81000000\0" \
	"kernelheader_size=0x40000\0" \
	"fdt_addr_r=0x90000000\0" \
	"load_addr=0xa0000000\0" \
	"kernel_size=0x2800000\0" \
	"kernel_size_sd=0x14000\0" \
	"kernelhdr_size_sd=0x20\0" \
	QSPI_MC_INIT_CMD \
	"mcmemsize=0x70000000\0" \
	BOOTENV \
	"boot_scripts=ls1088ardb_boot.scr\0" \
	"boot_script_hdr=hdr_ls1088ardb_bs.out\0" \
	"scan_dev_for_boot_part=" \
	"part list ${devtype} ${devnum} devplist; " \
	"env exists devplist \|\| setenv devplist 1; " \
	"for distro_bootpart in ${devplist}; do " \
	"if fstype ${devtype} " \
	"${devnum}:${distro_bootpart} " \
	"bootfstype; then " \
	"run scan_dev_for_boot; " \
	"fi; " \
	"done\0" \
	"boot_a_script=" \
	"load ${devtype} ${devnum}:${distro_bootpart} " \
	"${scriptaddr} ${prefix}${script}; " \
	"env exists secureboot && load ${devtype} " \
	"${devnum}:${distro_bootpart} " \
	"${scripthdraddr} ${prefix}${boot_script_hdr}; "\
	"env exists secureboot " \
	"&& esbc_validate ${scripthdraddr};" \
	"source ${scriptaddr}\0" \
	"installer=load mmc 0:2 $load_addr " \
	"/flex_installer_arm64.itb; " \
	"env exists mcinitcmd && run mcinitcmd && " \
	"mmc read 0x80001000 0x6800 0x800;" \
	"fsl_mc lazyapply dpl 0x80001000;" \
	"bootm $load_addr#ls1088ardb\0" \
	"qspi_bootcmd=echo Trying load from qspi..;" \
	"sf probe && sf read $load_addr " \
	"$kernel_addr $kernel_size ; env exists secureboot " \
	"&& sf read $kernelheader_addr_r $kernelheader_addr " \
	"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
	"bootm $load_addr#$BOARD\0" \
	"sd_bootcmd=echo Trying load from sd card..;" \
	"mmcinfo; mmc read $load_addr " \
	"$kernel_addr_sd $kernel_size_sd ;" \
	"env exists secureboot && mmc read $kernelheader_addr_r "\
	"$kernelhdr_addr_sd $kernelhdr_size_sd " \
	" && esbc_validate ${kernelheader_addr_r};" \
	"bootm $load_addr#$BOARD\0"
	#else
	#define CONFIG_EXTRA_ENV_SETTINGS \
	"BOARD=ls1088ardb\0" \
	"hwconfig=fsl_ddr:bank_intlv=auto\0" \
	"ramdisk_addr=0x800000\0" \
	"ramdisk_size=0x2000000\0" \
	"fdt_high=0xa0000000\0" \
	"initrd_high=0xffffffffffffffff\0" \
	"fdt_addr=0x64f00000\0" \
	"kernel_addr=0x1000000\0" \
	"kernel_addr_sd=0x8000\0" \
	"kernelhdr_addr_sd=0x3000\0" \
	"kernel_start=0x580100000\0" \
	"kernelheader_start=0x580800000\0" \
	"scriptaddr=0x80000000\0" \
	"scripthdraddr=0x80080000\0" \
	"fdtheader_addr_r=0x80100000\0" \
	"kernelheader_addr=0x600000\0" \
	"kernelheader_addr_r=0x80200000\0" \
	"kernel_addr_r=0x81000000\0" \
	"kernelheader_size=0x40000\0" \
	"fdt_addr_r=0x90000000\0" \
	"load_addr=0xa0000000\0" \
	"kernel_size=0x2800000\0" \
	"kernel_size_sd=0x14000\0" \
	"kernelhdr_size_sd=0x20\0" \
	MC_INIT_CMD \
	BOOTENV \
	"boot_scripts=ls1088ardb_boot.scr\0" \
	"boot_script_hdr=hdr_ls1088ardb_bs.out\0" \
	"scan_dev_for_boot_part=" \
	"part list ${devtype} ${devnum} devplist; " \
	"env exists devplist \|\| setenv devplist 1; " \
	"for distro_bootpart in ${devplist}; do " \
	"if fstype ${devtype} " \
	"${devnum}:${distro_bootpart} " \
	"bootfstype; then " \
	"run scan_dev_for_boot; " \
	"fi; " \
	"done\0" \
	"boot_a_script=" \
	"load ${devtype} ${devnum}:${distro_bootpart} " \
	"${scriptaddr} ${prefix}${script}; " \
	"env exists secureboot && load ${devtype} " \
	"${devnum}:${distro_bootpart} " \
	"${scripthdraddr} ${prefix}${boot_script_hdr} " \
	"&& esbc_validate ${scripthdraddr};" \
	"source ${scriptaddr}\0" \
	"installer=load mmc 0:2 $load_addr " \
	"/flex_installer_arm64.itb; " \
	"env exists mcinitcmd && run mcinitcmd && " \
	"mmc read 0x80001000 0x6800 0x800;" \
	"fsl_mc lazyapply dpl 0x80001000;" \
	"bootm $load_addr#ls1088ardb\0" \
	"qspi_bootcmd=echo Trying load from qspi..;" \
	"sf probe && sf read $load_addr " \
	"$kernel_addr $kernel_size ; env exists secureboot " \
	"&& sf read $kernelheader_addr_r $kernelheader_addr " \
	"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
	"bootm $load_addr#$BOARD\0" \
	"sd_bootcmd=echo Trying load from sd card..;" \
	"mmcinfo; mmc read $load_addr " \
	"$kernel_addr_sd $kernel_size_sd ;" \
	"env exists secureboot && mmc read $kernelheader_addr_r "\
	"$kernelhdr_addr_sd $kernelhdr_size_sd " \
	" && esbc_validate ${kernelheader_addr_r};" \
	"bootm $load_addr#$BOARD\0"
	#endif /* CONFIG_TFABOOT */

	#undef CONFIG_BOOTCOMMAND
	#ifdef CONFIG_TFABOOT
	#define QSPI_NOR_BOOTCOMMAND \
	"sf read 0x80001000 0xd00000 0x100000;" \
	"env exists mcinitcmd && env exists secureboot " \
	" && sf read 0x806C0000 0x6C0000 0x100000 " \
	"&& esbc_validate 0x806C0000;env exists mcinitcmd " \
	"&& fsl_mc lazyapply dpl 0x80001000;" \
	"run distro_bootcmd;run qspi_bootcmd;" \
	"env exists secureboot && esbc_halt;"
	#define SD_BOOTCOMMAND \
	"env exists mcinitcmd && mmcinfo; " \
	"mmc read 0x80001000 0x6800 0x800; " \
	"env exists mcinitcmd && env exists secureboot " \
	" && mmc read 0x806C0000 0x3600 0x20 " \
	"&& esbc_validate 0x806C0000;env exists mcinitcmd " \
	"&& fsl_mc lazyapply dpl 0x80001000;" \
	"run distro_bootcmd;run sd_bootcmd;" \
	"env exists secureboot && esbc_halt;"
	#else
	#if defined(CONFIG_QSPI_BOOT)
	/* Try to boot an on-QSPI kernel first, then do normal distro boot */
	#define CONFIG_BOOTCOMMAND \
	"sf read 0x80001000 0xd00000 0x100000;" \
	"env exists mcinitcmd && env exists secureboot " \
	" && sf read 0x806C0000 0x6C0000 0x100000 " \
	"&& esbc_validate 0x806C0000;env exists mcinitcmd " \
	"&& fsl_mc lazyapply dpl 0x80001000;" \
	"run distro_bootcmd;run qspi_bootcmd;" \
	"env exists secureboot && esbc_halt;"

	/* Try to boot an on-SD kernel first, then do normal distro boot */
	#elif defined(CONFIG_SD_BOOT)
	#define CONFIG_BOOTCOMMAND \
	"env exists mcinitcmd && mmcinfo; " \
	"mmc read 0x80001000 0x6800 0x800; " \
	"env exists mcinitcmd && env exists secureboot " \
	" && mmc read 0x806C0000 0x3600 0x20 " \
	"&& esbc_validate 0x806C0000;env exists mcinitcmd " \
	"&& fsl_mc lazyapply dpl 0x80001000;" \
	"run distro_bootcmd;run sd_bootcmd;" \
	"env exists secureboot && esbc_halt;"
	#endif
	#endif /* CONFIG_TFABOOT */

	/* MAC/PHY configuration */
	#ifdef CONFIG_FSL_MC_ENET
	#define AQ_PHY_ADDR1 0x00
	#define AQR105_IRQ_MASK 0x00000004

	#define QSGMII1_PORT1_PHY_ADDR 0x0c
	#define QSGMII1_PORT2_PHY_ADDR 0x0d
	#define QSGMII1_PORT3_PHY_ADDR 0x0e
	#define QSGMII1_PORT4_PHY_ADDR 0x0f
	#define QSGMII2_PORT1_PHY_ADDR 0x1c
	#define QSGMII2_PORT2_PHY_ADDR 0x1d
	#define QSGMII2_PORT3_PHY_ADDR 0x1e
	#define QSGMII2_PORT4_PHY_ADDR 0x1f

	#define CONFIG_ETHPRIME "DPMAC1@xgmii"
	#define CONFIG_PHY_GIGE
	#endif
	#endif

	#ifndef SPL_NO_ENV

	#define BOOT_TARGET_DEVICES(func) \
	func(MMC, mmc, 0) \
	func(USB, usb, 0) \
	func(SCSI, scsi, 0) \
	func(DHCP, dhcp, na)
	#include <config_distro_bootcmd.h>
	#endif

	#include <asm/fsl_secure_boot.h>

	#endif /* __LS1088A_RDB_H */