tegra2: Move board_mmc_init into board files
For Seaboard, this is mostly a cut/paste of board_mmc_init() and
pin_mux_mmc() into seaboard.c; pin_mux_mmc() was modified to add some
missing pinmux_tristate_disable calls for the GPIOs.
For Harmony, those functions were modified to configure SDMMC2 (index 2)
instead of SDMMC3 (index 1), since that's what is present on the board.
However, harmony.c is still missing the required GPIO setup, so neither
port is likely to function correctly yet. This will be fixed in the next
change.
v4: Include board.h to prototype tegra2_mmc_init().
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
diff --git a/board/nvidia/harmony/harmony.c b/board/nvidia/harmony/harmony.c
index cbb30d6..f2c3867 100644
--- a/board/nvidia/harmony/harmony.c
+++ b/board/nvidia/harmony/harmony.c
@@ -24,9 +24,11 @@
#include <common.h>
#include <asm/io.h>
#include <asm/arch/tegra2.h>
+#include <asm/arch/pinmux.h>
#ifdef CONFIG_TEGRA2_MMC
#include <mmc.h>
#endif
+#include "../common/board.h"
/*
* Routine: gpio_config_uart
@@ -38,6 +40,39 @@
#ifdef CONFIG_TEGRA2_MMC
/*
+ * Routine: pin_mux_mmc
+ * Description: setup the pin muxes/tristate values for the SDMMC(s)
+ */
+static void pin_mux_mmc(void)
+{
+ /* SDMMC4: config 3, x8 on 2nd set of pins */
+ pinmux_set_func(PINGRP_ATB, PMUX_FUNC_SDIO4);
+ pinmux_set_func(PINGRP_GMA, PMUX_FUNC_SDIO4);
+ pinmux_set_func(PINGRP_GME, PMUX_FUNC_SDIO4);
+
+ pinmux_tristate_disable(PINGRP_ATB);
+ pinmux_tristate_disable(PINGRP_GMA);
+ pinmux_tristate_disable(PINGRP_GME);
+
+ /* For power GPIO PI6 */
+ pinmux_tristate_disable(PINGRP_ATA);
+ /* For CD GPIO PH2 */
+ pinmux_tristate_disable(PINGRP_ATD);
+
+ /* SDMMC2: SDIO2_CLK, SDIO2_CMD, SDIO2_DAT[7:0] */
+ pinmux_set_func(PINGRP_DTA, PMUX_FUNC_SDIO2);
+ pinmux_set_func(PINGRP_DTD, PMUX_FUNC_SDIO2);
+
+ pinmux_tristate_disable(PINGRP_DTA);
+ pinmux_tristate_disable(PINGRP_DTD);
+
+ /* For power GPIO PT3 */
+ pinmux_tristate_disable(PINGRP_DTB);
+ /* For CD GPIO PI5 */
+ pinmux_tristate_disable(PINGRP_ATC);
+}
+
+/*
* Routine: gpio_config_mmc
* Description: Set GPIOs for SD card
*/
@@ -47,6 +82,27 @@
}
/* this is a weak define that we are overriding */
+int board_mmc_init(bd_t *bd)
+{
+ debug("board_mmc_init called\n");
+
+ /* Enable muxes, etc. for SDMMC controllers */
+ pin_mux_mmc();
+ gpio_config_mmc();
+
+ debug("board_mmc_init: init SD slot J26\n");
+ /* init dev 0, SD slot J26, with 4-bit bus */
+ /* The board has an 8-bit bus, but 8-bit doesn't work yet */
+ tegra2_mmc_init(0, 4);
+
+ debug("board_mmc_init: init SD slot J5\n");
+ /* init dev 2, SD slot J5, with 4-bit bus */
+ tegra2_mmc_init(2, 4);
+
+ return 0;
+}
+
+/* this is a weak define that we are overriding */
int board_mmc_getcd(u8 *cd, struct mmc *mmc)
{
debug("board_mmc_getcd called\n");