dm: i2c: use CONFIG_IS_ENABLED macro for DM_I2C/DM_I2C_GPIO
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c
index 2cd0a12..bc1657e 100644
--- a/board/ti/am335x/board.c
+++ b/board/ti/am335x/board.c
@@ -77,7 +77,7 @@
void do_board_detect(void)
{
enable_i2c0_pin_mux();
-#ifndef CONFIG_DM_I2C
+#if !CONFIG_IS_ENABLED(DM_I2C)
i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
#endif
if (ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS,
@@ -336,7 +336,7 @@
if (board_is_bone() && !strncmp(board_ti_get_rev(), "00A1", 4))
return;
-#ifndef CONFIG_DM_I2C
+#if !CONFIG_IS_ENABLED(DM_I2C)
if (i2c_probe(TPS65217_CHIP_PM))
return;
#else
@@ -435,7 +435,7 @@
* 1.10V. For MPU voltage we need to switch based on
* the frequency we are running at.
*/
-#ifndef CONFIG_DM_I2C
+#if !CONFIG_IS_ENABLED(DM_I2C)
if (i2c_probe(TPS65910_CTRL_I2C_ADDR))
return;
#else
@@ -469,7 +469,7 @@
if (first_time) {
enable_i2c0_pin_mux();
-#ifndef CONFIG_DM_I2C
+#if !CONFIG_IS_ENABLED(DM_I2C)
i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED,
CONFIG_SYS_OMAP24_I2C_SLAVE);
#endif