/*
 *  crt0 - C-runtime startup Code for ARM U-Boot
 *
 *  Copyright (c) 2012  Albert ARIBAUD <albert.u.boot@aribaud.net>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <config.h>
#include <asm-offsets.h>
#include <linux/linkage.h>

/*
 * This file handles the target-independent stages of the U-Boot
 * start-up where a C runtime environment is needed. Its entry point
 * is _main and is branched into from the target's start.S file.
 *
 * _main execution sequence is:
 *
 * 1. Set up initial environment for calling board_init_f().
 *    This environment only provides a stack and a place to store
 *    the GD ('global data') structure, both located in some readily
 *    available RAM (SRAM, locked cache...). In this context, VARIABLE
 *    global data, initialized or not (BSS), are UNAVAILABLE; only
 *    CONSTANT initialized data are available.
 *
 * 2. Call board_init_f(). This function prepares the hardware for
 *    execution from system RAM (DRAM, DDR...) As system RAM may not
 *    be available yet, , board_init_f() must use the current GD to
 *    store any data which must be passed on to later stages. These
 *    data include the relocation destination, the future stack, and
 *    the future GD location.
 *
 * (the following applies only to non-SPL builds)
 *
 * 3. Set up intermediate environment where the stack and GD are the
 *    ones allocated by board_init_f() in system RAM, but BSS and
 *    initialized non-const data are still not available.
 *
 * 4. Call relocate_code(). This function relocates U-Boot from its
 *    current location into the relocation destination computed by
 *    board_init_f().
 *
 * 5. Set up final environment for calling board_init_r(). This
 *    environment has BSS (initialized to 0), initialized non-const
 *    data (initialized to their intended value), and stack in system
 *    RAM. GD has retained values set by board_init_f(). Some CPUs
 *    have some work left to do at this point regarding memory, so
 *    call c_runtime_cpu_setup.
 *
 * 6. Branch to board_init_r().
 */

/*
 * entry point of crt0 sequence
 */

ENTRY(_main)

/*
 * Set up initial C runtime environment and call board_init_f(0).
 */

#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_STACK)
	ldr	sp, =(CONFIG_SPL_STACK)
#else
	ldr	sp, =(CONFIG_SYS_INIT_SP_ADDR)
#endif
	bic	sp, sp, #7	/* 8-byte alignment for ABI compliance */
	mov	r2, sp
	sub	sp, sp, #GD_SIZE	/* allocate one GD above SP */
	bic	sp, sp, #7	/* 8-byte alignment for ABI compliance */
	mov	r9, sp		/* GD is above SP */
	mov	r1, sp
	mov	r0, #0
clr_gd:
	cmp	r1, r2			/* while not at end of GD */
	strlo	r0, [r1]		/* clear 32-bit GD word */
	addlo	r1, r1, #4		/* move to next */
	blo	clr_gd

	/* mov r0, #0 not needed due to above code */
	bl	board_init_f

#if ! defined(CONFIG_SPL_BUILD)

/*
 * Set up intermediate environment (new sp and gd) and call
 * relocate_code(addr_moni). Trick here is that we'll return
 * 'here' but relocated.
 */

	ldr	sp, [r9, #GD_START_ADDR_SP]	/* sp = gd->start_addr_sp */
	bic	sp, sp, #7	/* 8-byte alignment for ABI compliance */
	ldr	r9, [r9, #GD_BD]		/* r9 = gd->bd */
	sub	r9, r9, #GD_SIZE		/* new GD is below bd */

	adr	lr, here
	ldr	r0, [r9, #GD_RELOC_OFF]		/* r0 = gd->reloc_off */
	add	lr, lr, r0
	ldr	r0, [r9, #GD_RELOCADDR]		/* r0 = gd->relocaddr */
	b	relocate_code
here:

/* Set up final (full) environment */

	bl	c_runtime_cpu_setup	/* we still call old routine here */

	ldr	r0, =__bss_start	/* this is auto-relocated! */
	ldr	r1, =__bss_end		/* this is auto-relocated! */

	mov	r2, #0x00000000		/* prepare zero to clear BSS */

clbss_l:cmp	r0, r1			/* while not at end of BSS */
	strlo	r2, [r0]		/* clear 32-bit BSS word */
	addlo	r0, r0, #4		/* move to next */
	blo	clbss_l

	bl coloured_LED_init
	bl red_led_on

	/* call board_init_r(gd_t *id, ulong dest_addr) */
	mov     r0, r9                  /* gd_t */
	ldr	r1, [r9, #GD_RELOCADDR]	/* dest_addr */
	/* call board_init_r */
	ldr	pc, =board_init_r	/* this is auto-relocated! */

	/* we should not return here. */

#endif

ENDPROC(_main)