/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * Copyright 2011-2013 Freescale Semiconductor, Inc.
 * Copyright 2020-2021 NXP
 */

/*
 * T2080/T2081 QDS board configuration file
 */

#ifndef __T208xQDS_H
#define __T208xQDS_H

#include <linux/stringify.h>

#define CONFIG_ICS307_REFCLK_HZ 25000000  /* ICS307 ref clk freq */
#if defined(CONFIG_ARCH_T2080)
#define CONFIG_FSL_SATA_V2
#define CONFIG_SYS_SRIO		/* Enable Serial RapidIO Support */
#define CONFIG_SRIO1		/* SRIO port 1 */
#define CONFIG_SRIO2		/* SRIO port 2 */
#endif

/* High Level Configuration Options */
#define CONFIG_SYS_BOOK3E_HV	/* Category E.HV supported */
#define CONFIG_ENABLE_36BIT_PHYS

#define CONFIG_SYS_FSL_CPC	/* Corenet Platform Cache */
#define CONFIG_SYS_NUM_CPC	CONFIG_SYS_NUM_DDR_CTLRS

#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_SPL_FLUSH_IMAGE
#define CONFIG_SPL_PAD_TO		0x40000
#define CONFIG_SPL_MAX_SIZE		0x28000
#define RESET_VECTOR_OFFSET		0x27FFC
#define BOOT_PAGE_OFFSET		0x27000
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SPL_SKIP_RELOCATE
#define CONFIG_SPL_COMMON_INIT_DDR
#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
#endif

#ifdef CONFIG_MTD_RAW_NAND
#define CONFIG_SYS_NAND_U_BOOT_SIZE	(768 << 10)
#define CONFIG_SYS_NAND_U_BOOT_DST	0x00200000
#define CONFIG_SYS_NAND_U_BOOT_START	0x00200000
#ifndef CONFIG_MPC85XX_HAVE_RESET_VECTOR
#define CONFIG_SYS_MPC85XX_NO_RESETVEC
#endif
#endif

#ifdef CONFIG_SPIFLASH
#define	CONFIG_RESET_VECTOR_ADDRESS		0x200FFC
#define CONFIG_SPL_SPI_FLASH_MINIMAL
#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE	(768 << 10)
#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST		(0x00200000)
#define CONFIG_SYS_SPI_FLASH_U_BOOT_START	(0x00200000)
#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS	(256 << 10)
#ifndef CONFIG_SPL_BUILD
#define	CONFIG_SYS_MPC85XX_NO_RESETVEC
#endif
#endif

#ifdef CONFIG_SDCARD
#define	CONFIG_RESET_VECTOR_ADDRESS		0x200FFC
#define CONFIG_SYS_MMC_U_BOOT_SIZE	(768 << 10)
#define CONFIG_SYS_MMC_U_BOOT_DST	(0x00200000)
#define CONFIG_SYS_MMC_U_BOOT_START	(0x00200000)
#define CONFIG_SYS_MMC_U_BOOT_OFFS	(260 << 10)
#ifndef CONFIG_SPL_BUILD
#define	CONFIG_SYS_MPC85XX_NO_RESETVEC
#endif
#endif

#endif /* CONFIG_RAMBOOT_PBL */

#define CONFIG_SRIO_PCIE_BOOT_MASTER
#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
/* Set 1M boot space */
#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
		(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
#endif

#ifndef CONFIG_RESET_VECTOR_ADDRESS
#define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
#endif

/*
 * These can be toggled for performance analysis, otherwise use default.
 */
#define CONFIG_SYS_CACHE_STASHING
#ifdef CONFIG_DDR_ECC
#define CONFIG_MEM_INIT_VALUE		0xdeadbeef
#endif

/*
 * Config the L3 Cache as L3 SRAM
 */
#define CONFIG_SYS_INIT_L3_ADDR		0xFFFC0000
#define CONFIG_SYS_L3_SIZE		(512 << 10)
#define CONFIG_SPL_GD_ADDR		(CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
#define SPL_ENV_ADDR			(CONFIG_SPL_GD_ADDR + 4 * 1024)
#define CONFIG_SPL_RELOC_MALLOC_ADDR	(CONFIG_SPL_GD_ADDR + 12 * 1024)
#define CONFIG_SPL_RELOC_MALLOC_SIZE	(50 << 10)
#define CONFIG_SPL_RELOC_STACK		(CONFIG_SPL_GD_ADDR + 64 * 1024)

#define CONFIG_SYS_DCSRBAR	0xf0000000
#define CONFIG_SYS_DCSRBAR_PHYS	0xf00000000ull

/* EEPROM */
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM	0

/*
 * DDR Setup
 */
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_SYS_SPD_BUS_NUM	0
#define CONFIG_SYS_SDRAM_SIZE	2048	/* for fixed parameter use */
#define SPD_EEPROM_ADDRESS1	0x51
#define SPD_EEPROM_ADDRESS2	0x52
#define SPD_EEPROM_ADDRESS	SPD_EEPROM_ADDRESS1
#define CTRL_INTLV_PREFERED	cacheline

/*
 * IFC Definitions
 */
#define CONFIG_SYS_FLASH_BASE		0xe0000000
#define CONFIG_SYS_FLASH_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_NOR0_CSPR_EXT	(0xf)
#define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
				+ 0x8000000) | \
				CSPR_PORT_SIZE_16 | \
				CSPR_MSEL_NOR | \
				CSPR_V)
#define CONFIG_SYS_NOR1_CSPR_EXT	(0xf)
#define CONFIG_SYS_NOR1_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
				CSPR_PORT_SIZE_16 | \
				CSPR_MSEL_NOR | \
				CSPR_V)
#define CONFIG_SYS_NOR_AMASK	IFC_AMASK(128*1024*1024)
/* NOR Flash Timing Params */
#define CONFIG_SYS_NOR_CSOR	CSOR_NAND_TRHZ_80

#define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
				FTIM0_NOR_TEADC(0x5) | \
				FTIM0_NOR_TEAHC(0x5))
#define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \
				FTIM1_NOR_TRAD_NOR(0x1A) |\
				FTIM1_NOR_TSEQRAD_NOR(0x13))
#define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \
				FTIM2_NOR_TCH(0x4) | \
				FTIM2_NOR_TWPH(0x0E) | \
				FTIM2_NOR_TWP(0x1c))
#define CONFIG_SYS_NOR_FTIM3	0x0

#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */

#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */

#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS \
					+ 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}

#define QIXIS_BASE			0xffdf0000
#define QIXIS_LBMAP_SWITCH		6
#define QIXIS_LBMAP_MASK		0x0f
#define QIXIS_LBMAP_SHIFT		0
#define QIXIS_LBMAP_DFLTBANK		0x00
#define QIXIS_LBMAP_ALTBANK		0x04
#define QIXIS_LBMAP_NAND		0x09
#define QIXIS_LBMAP_SD			0x00
#define QIXIS_RCW_SRC_NAND		0x104
#define QIXIS_RCW_SRC_SD		0x040
#define QIXIS_RST_CTL_RESET		0x83
#define QIXIS_RST_FORCE_MEM		0x1
#define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
#define QIXIS_RCFG_CTL_RECONFIG_START	0x21
#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
#define QIXIS_BASE_PHYS		(0xf00000000ull | QIXIS_BASE)

#define CONFIG_SYS_CSPR3_EXT	(0xf)
#define CONFIG_SYS_CSPR3	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
				| CSPR_PORT_SIZE_8 \
				| CSPR_MSEL_GPCM \
				| CSPR_V)
#define CONFIG_SYS_AMASK3	IFC_AMASK(64 * 1024)
#define CONFIG_SYS_CSOR3	0x0
/* QIXIS Timing parameters for IFC CS3 */
#define CONFIG_SYS_CS3_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \
					FTIM0_GPCM_TEADC(0x0e) | \
					FTIM0_GPCM_TEAHC(0x0e))
#define CONFIG_SYS_CS3_FTIM1		(FTIM1_GPCM_TACO(0xff) | \
					FTIM1_GPCM_TRAD(0x3f))
#define CONFIG_SYS_CS3_FTIM2		(FTIM2_GPCM_TCS(0x0e) | \
					FTIM2_GPCM_TCH(0x8) | \
					FTIM2_GPCM_TWP(0x1f))
#define CONFIG_SYS_CS3_FTIM3		0x0

/* NAND Flash on IFC */
#define CONFIG_SYS_NAND_BASE		0xff800000
#define CONFIG_SYS_NAND_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_NAND_BASE)

#define CONFIG_SYS_NAND_CSPR_EXT	(0xf)
#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
				| CSPR_MSEL_NAND	 /* MSEL = NAND */ \
				| CSPR_V)
#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)

#define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN	/* ECC on encode */ \
				| CSOR_NAND_ECC_DEC_EN	/* ECC on decode */ \
				| CSOR_NAND_ECC_MODE_4	/* 4-bit ECC */	    \
				| CSOR_NAND_RAL_3	/* RAL = 2Byes */   \
				| CSOR_NAND_PGS_2K	/* Page Size = 2K */\
				| CSOR_NAND_SPRZ_64	/* Spare size = 64 */\
				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/

/* ONFI NAND Flash mode0 Timing Params */
#define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \
					FTIM0_NAND_TWP(0x18)    | \
					FTIM0_NAND_TWCHT(0x07)  | \
					FTIM0_NAND_TWH(0x0a))
#define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
					FTIM1_NAND_TWBE(0x39)   | \
					FTIM1_NAND_TRR(0x0e)    | \
					FTIM1_NAND_TRP(0x18))
#define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x0f)  | \
					FTIM2_NAND_TREH(0x0a)   | \
					FTIM2_NAND_TWHRE(0x1e))
#define CONFIG_SYS_NAND_FTIM3		0x0

#define CONFIG_SYS_NAND_DDR_LAW		11
#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE	1

#if defined(CONFIG_MTD_RAW_NAND)
#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR0_CSPR
#define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR1_CSPR_EXT
#define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR1_CSPR
#define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3
#else
#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR
#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR1_CSPR_EXT
#define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR
#define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
#endif

#if defined(CONFIG_RAMBOOT_PBL)
#define CONFIG_SYS_RAMBOOT
#endif

#define CONFIG_HWCONFIG

/* define to use L1 as initial stack */
#define CONFIG_L1_INIT_RAM
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR	0xfdd00000 /* Initial L1 address */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH	0xf
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW	0xfe03c000
/* The assembler doesn't like typecast */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
			((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
			CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
#define CONFIG_SYS_INIT_RAM_SIZE	0x00004000
#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
						GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)

/*
 * Serial Port
 */
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE	1
#define CONFIG_SYS_NS16550_CLK		(get_bus_freq(0)/2)
#define CONFIG_SYS_BAUDRATE_TABLE	\
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)

/*
 * I2C
 */

#define I2C_MUX_PCA_ADDR_PRI	0x77 /* I2C bus multiplexer,primary */
#define I2C_MUX_PCA_ADDR_SEC1	0x75 /* I2C bus multiplexer,secondary 1 */
#define I2C_MUX_PCA_ADDR_SEC2	0x76 /* I2C bus multiplexer,secondary 2 */
#define I2C_MUX_CH_DEFAULT	0x8

#define I2C_MUX_CH_VOL_MONITOR 0xa

/* Voltage monitor on channel 2*/
#define I2C_VOL_MONITOR_ADDR           0x40
#define I2C_VOL_MONITOR_BUS_V_OFFSET   0x2
#define I2C_VOL_MONITOR_BUS_V_OVF      0x1
#define I2C_VOL_MONITOR_BUS_V_SHIFT    3

/* The lowest and highest voltage allowed for T208xQDS */
#define VDD_MV_MIN			819
#define VDD_MV_MAX			1212

/*
 * RapidIO
 */
#define CONFIG_SYS_SRIO1_MEM_VIRT	0xa0000000
#define CONFIG_SYS_SRIO1_MEM_PHYS	0xc20000000ull
#define CONFIG_SYS_SRIO1_MEM_SIZE	0x10000000 /* 256M */
#define CONFIG_SYS_SRIO2_MEM_VIRT	0xb0000000
#define CONFIG_SYS_SRIO2_MEM_PHYS	0xc30000000ull
#define CONFIG_SYS_SRIO2_MEM_SIZE	0x10000000 /* 256M */
/*
 * for slave u-boot IMAGE instored in master memory space,
 * PHYS must be aligned based on the SIZE
 */
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE     0x100000 /* 1M */
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
/*
 * for slave UCODE and ENV instored in master memory space,
 * PHYS must be aligned based on the SIZE
 */
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE    0x40000	/* 256K */

/* slave core release by master*/
#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */

/*
 * SRIO_PCIE_BOOT - SLAVE
 */
#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
		(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
#endif

/*
 * eSPI - Enhanced SPI
 */

/*
 * General PCI
 * Memory space is mapped 1-1, but I/O space must start from 0.
 */
#define CONFIG_PCIE1		/* PCIE controller 1 */
#define CONFIG_PCIE2		/* PCIE controller 2 */
#define CONFIG_PCIE3		/* PCIE controller 3 */
#define CONFIG_PCIE4		/* PCIE controller 4 */
/* controller 1, direct to uli, tgtid 3, Base address 20000 */
#define CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
#define CONFIG_SYS_PCIE1_MEM_PHYS	0xc00000000ull
#define CONFIG_SYS_PCIE1_IO_VIRT	0xf8000000
#define CONFIG_SYS_PCIE1_IO_PHYS	0xff8000000ull

/* controller 2, Slot 2, tgtid 2, Base address 201000 */
#define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
#define CONFIG_SYS_PCIE2_MEM_PHYS	0xc20000000ull
#define CONFIG_SYS_PCIE2_IO_VIRT	0xf8010000
#define CONFIG_SYS_PCIE2_IO_PHYS	0xff8010000ull

/* controller 3, Slot 1, tgtid 1, Base address 202000 */
#define CONFIG_SYS_PCIE3_MEM_VIRT	0xb0000000
#define CONFIG_SYS_PCIE3_MEM_PHYS	0xc30000000ull
#define CONFIG_SYS_PCIE3_IO_VIRT	0xf8020000
#define CONFIG_SYS_PCIE3_IO_PHYS	0xff8020000ull

/* controller 4, Base address 203000 */
#define CONFIG_SYS_PCIE4_MEM_VIRT       0xc0000000
#define CONFIG_SYS_PCIE4_MEM_PHYS	0xc40000000ull
#define CONFIG_SYS_PCIE4_IO_PHYS	0xff8030000ull

#ifdef CONFIG_PCI
#define CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
#endif

/* Qman/Bman */
#ifndef CONFIG_NOBQFMAN
#define CONFIG_SYS_BMAN_NUM_PORTALS	18
#define CONFIG_SYS_BMAN_MEM_BASE	0xf4000000
#define CONFIG_SYS_BMAN_MEM_PHYS	0xff4000000ull
#define CONFIG_SYS_BMAN_MEM_SIZE	0x02000000
#define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
#define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
#define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
#define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
					CONFIG_SYS_BMAN_CENA_SIZE)
#define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
#define CONFIG_SYS_QMAN_NUM_PORTALS	18
#define CONFIG_SYS_QMAN_MEM_BASE	0xf6000000
#define CONFIG_SYS_QMAN_MEM_PHYS	0xff6000000ull
#define CONFIG_SYS_QMAN_MEM_SIZE	0x02000000
#define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
#define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
#define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
#define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
					CONFIG_SYS_QMAN_CENA_SIZE)
#define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_QMAN_SWP_ISDR_REG	0xE08

#define CONFIG_SYS_DPAA_FMAN
#define CONFIG_SYS_DPAA_PME
#define CONFIG_SYS_PMAN
#define CONFIG_SYS_DPAA_DCE
#define CONFIG_SYS_DPAA_RMAN		/* RMan */
#define CONFIG_SYS_INTERLAKEN

#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
#endif /* CONFIG_NOBQFMAN */

#ifdef CONFIG_SYS_DPAA_FMAN
#define RGMII_PHY1_ADDR	0x1
#define RGMII_PHY2_ADDR	0x2
#define FM1_10GEC1_PHY_ADDR	  0x3
#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
#define SGMII_CARD_PORT2_PHY_ADDR 0x1D
#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
#endif

/*
 * SATA
 */
#ifdef CONFIG_FSL_SATA_V2
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1		CONFIG_SYS_MPC85xx_SATA1_ADDR
#define CONFIG_SYS_SATA1_FLAGS		FLAGS_DMA
#define CONFIG_SATA2
#define CONFIG_SYS_SATA2		CONFIG_SYS_MPC85xx_SATA2_ADDR
#define CONFIG_SYS_SATA2_FLAGS		FLAGS_DMA
#define CONFIG_LBA48
#endif

/*
 * USB
 */
#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_HAS_FSL_DR_USB
#endif

/*
 * SDHC
 */
#ifdef CONFIG_MMC
#define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC85xx_ESDHC_ADDR
#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
#endif

/*
 * Dynamic MTD Partition support with mtdparts
 */

/*
 * Environment
 */
#define CONFIG_LOADS_ECHO	/* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */

/*
 * Miscellaneous configurable options
 */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 64 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial map for Linux*/
#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */

/*
 * Environment Configuration
 */
#define CONFIG_ROOTPATH	 "/opt/nfsroot"
#define CONFIG_UBOOTPATH "u-boot.bin"	/* U-Boot image on TFTP server */

#define __USB_PHY_TYPE		utmi

#define	CONFIG_EXTRA_ENV_SETTINGS				\
	"hwconfig=fsl_ddr:"					\
	"ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","	\
	"bank_intlv=auto;"					\
	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
	"netdev=eth0\0"						\
	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\
	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"	\
	"tftpflash=tftpboot $loadaddr $uboot && "		\
	"protect off $ubootaddr +$filesize && "			\
	"erase $ubootaddr +$filesize && "			\
	"cp.b $loadaddr $ubootaddr $filesize && "		\
	"protect on $ubootaddr +$filesize && "			\
	"cmp.b $loadaddr $ubootaddr $filesize\0"		\
	"consoledev=ttyS0\0"					\
	"ramdiskaddr=2000000\0"					\
	"ramdiskfile=t2080qds/ramdisk.uboot\0"			\
	"fdtaddr=1e00000\0"					\
	"fdtfile=t2080qds/t2080qds.dtb\0"			\
	"bdev=sda3\0"

/*
 * For emulation this causes u-boot to jump to the start of the
 * proof point app code automatically
 */
#define PROOF_POINTS				\
	"setenv bootargs root=/dev/$bdev rw "		\
	"console=$consoledev,$baudrate $othbootargs;"	\
	"cpu 1 release 0x29000000 - - -;"		\
	"cpu 2 release 0x29000000 - - -;"		\
	"cpu 3 release 0x29000000 - - -;"		\
	"cpu 4 release 0x29000000 - - -;"		\
	"cpu 5 release 0x29000000 - - -;"		\
	"cpu 6 release 0x29000000 - - -;"		\
	"cpu 7 release 0x29000000 - - -;"		\
	"go 0x29000000"

#define HVBOOT				\
	"setenv bootargs config-addr=0x60000000; "	\
	"bootm 0x01000000 - 0x00f00000"

#define ALU				\
	"setenv bootargs root=/dev/$bdev rw "		\
	"console=$consoledev,$baudrate $othbootargs;"	\
	"cpu 1 release 0x01000000 - - -;"		\
	"cpu 2 release 0x01000000 - - -;"		\
	"cpu 3 release 0x01000000 - - -;"		\
	"cpu 4 release 0x01000000 - - -;"		\
	"cpu 5 release 0x01000000 - - -;"		\
	"cpu 6 release 0x01000000 - - -;"		\
	"cpu 7 release 0x01000000 - - -;"		\
	"go 0x01000000"

#include <asm/fsl_secure_boot.h>

#endif	/* __T208xQDS_H */