Add "pcidelay" environment variable (in ms, enabled via CONFIG_PCI_BOOTDELAY).
diff --git a/CHANGELOG b/CHANGELOG
index a0bf5e2..d103759 100644
--- a/CHANGELOG
+++ b/CHANGELOG
@@ -2,6 +2,12 @@
Changes since U-Boot 0.2.1:
======================================================================
+* Patch by Stefan Roese, 13 Feb 2003:
+ Add "pcidelay" environment variable (in ms, enabled via
+ CONFIG_PCI_BOOTDELAY).
+ PCI spec 2.2 defines, that a pci target has 2^25 pci clocks after
+ RST# to respond to configuration cycles (33MHz -> 1s).
+
* Patch by Stefan Roese, 10 Feb 2003:
Add support for 4MB and 128MB onboard SDRAM (cpu/ppc4xx/sdram.c)
diff --git a/board/MAI/AmigaOneG3SE/AmigaOneG3SE.c b/board/MAI/AmigaOneG3SE/AmigaOneG3SE.c
index 9d5c24e..1d6ca81 100644
--- a/board/MAI/AmigaOneG3SE/AmigaOneG3SE.c
+++ b/board/MAI/AmigaOneG3SE/AmigaOneG3SE.c
@@ -107,7 +107,7 @@
}
-void pci_init (void)
+void pci_init_board (void)
{
#ifndef CONFIG_RAMBOOT
articiaS_pci_init ();
diff --git a/board/bmw/bmw.c b/board/bmw/bmw.c
index 25a710f..2685662 100644
--- a/board/bmw/bmw.c
+++ b/board/bmw/bmw.c
@@ -102,7 +102,7 @@
*/
struct pci_controller hose;
-void pci_init (void)
+void pci_init_board (void)
{
pci_mpc824x_init(&hose);
/* pci_dev_init(0); */
diff --git a/board/cu824/cu824.c b/board/cu824/cu824.c
index 20aaea2..a7c583c 100644
--- a/board/cu824/cu824.c
+++ b/board/cu824/cu824.c
@@ -113,7 +113,7 @@
#endif
};
-void pci_init(void)
+void pci_init_board(void)
{
pci_mpc824x_init(&hose);
}
diff --git a/board/eltec/bab7xx/pci.c b/board/eltec/bab7xx/pci.c
index 2fd8e13..a5fcfef 100644
--- a/board/eltec/bab7xx/pci.c
+++ b/board/eltec/bab7xx/pci.c
@@ -33,7 +33,7 @@
struct pci_controller local_hose;
-void pci_init(void)
+void pci_init_board(void)
{
struct pci_controller* hose = (struct pci_controller *)&local_hose;
u32 reg32;
diff --git a/board/eltec/elppc/pci.c b/board/eltec/elppc/pci.c
index 07158e6..2bbb5f2 100644
--- a/board/eltec/elppc/pci.c
+++ b/board/eltec/elppc/pci.c
@@ -33,7 +33,7 @@
struct pci_controller local_hose;
-void pci_init(void)
+void pci_init_board(void)
{
struct pci_controller* hose = (struct pci_controller *)&local_hose;
u16 reg16;
diff --git a/board/esd/common/pci.c b/board/esd/common/pci.c
index f8f180c..f711205 100644
--- a/board/esd/common/pci.c
+++ b/board/esd/common/pci.c
@@ -166,7 +166,7 @@
config_table: pci9054_config_table,
};
-void pci_init(void)
+void pci_init_board(void)
{
struct pci_controller *hose = &pci9054_hose;
diff --git a/board/evb64260/pci.c b/board/evb64260/pci.c
index 8e9178d..585906d 100644
--- a/board/evb64260/pci.c
+++ b/board/evb64260/pci.c
@@ -597,7 +597,7 @@
};
void
-pci_init(void)
+pci_init_board(void)
{
unsigned int command;
diff --git a/board/mousse/pci.c b/board/mousse/pci.c
index 89ca235..4f39398 100644
--- a/board/mousse/pci.c
+++ b/board/mousse/pci.c
@@ -277,7 +277,7 @@
fixup_irq: pci_mousse_fixup_irq,
};
-void pci_init(void)
+void pci_init_board(void)
{
pci_mpc824x_init(&hose);
}
diff --git a/board/mpl/common/pci.c b/board/mpl/common/pci.c
index d1965f9..a26f542 100644
--- a/board/mpl/common/pci.c
+++ b/board/mpl/common/pci.c
@@ -90,7 +90,7 @@
fixup_irq: pci_pip405_fixup_irq,
};
-void pci_init(void)
+void pci_init_board(void)
{
/*we want the ptrs to RAM not flash (ie don't use init list)*/
hose.fixup_irq = pci_pip405_fixup_irq;
diff --git a/board/musenki/musenki.c b/board/musenki/musenki.c
index 3b02f37..d805f09 100644
--- a/board/musenki/musenki.c
+++ b/board/musenki/musenki.c
@@ -124,7 +124,7 @@
#endif
};
-void pci_init(void)
+void pci_init_board(void)
{
pci_mpc824x_init(&hose);
}
diff --git a/board/oxc/oxc.c b/board/oxc/oxc.c
index 8aced84..5f5e59a 100644
--- a/board/oxc/oxc.c
+++ b/board/oxc/oxc.c
@@ -108,7 +108,7 @@
#endif
};
-void pci_init (void)
+void pci_init_board (void)
{
pci_mpc824x_init(&hose);
}
diff --git a/board/pcippc2/pcippc2.c b/board/pcippc2/pcippc2.c
index 80ca402..bab3c20 100644
--- a/board/pcippc2/pcippc2.c
+++ b/board/pcippc2/pcippc2.c
@@ -135,7 +135,7 @@
return (0);
}
-void pci_init (void)
+void pci_init_board (void)
{
cpc710_pci_init ();
diff --git a/board/pn62/pn62.c b/board/pn62/pn62.c
index 4d87527..9b1fc00 100644
--- a/board/pn62/pn62.c
+++ b/board/pn62/pn62.c
@@ -137,7 +137,7 @@
struct pci_controller hose = {
};
-void pci_init (void)
+void pci_init_board (void)
{
show_startup_phase (4);
pci_mpc824x_init (&hose);
diff --git a/board/sandpoint/sandpoint.c b/board/sandpoint/sandpoint.c
index 8d385f7..fe1c0a0 100644
--- a/board/sandpoint/sandpoint.c
+++ b/board/sandpoint/sandpoint.c
@@ -121,7 +121,7 @@
#endif
};
-void pci_init(void)
+void pci_init_board(void)
{
pci_mpc824x_init(&hose);
}
diff --git a/board/sc520_cdp/sc520_cdp.c b/board/sc520_cdp/sc520_cdp.c
index 41f5e3a..ba6255f 100644
--- a/board/sc520_cdp/sc520_cdp.c
+++ b/board/sc520_cdp/sc520_cdp.c
@@ -31,35 +31,35 @@
static void irq_init(void)
{
-
+
/* disable global interrupt mode */
- write_mmcr_byte(SC520_PICICR, 0x40);
-
+ write_mmcr_byte(SC520_PICICR, 0x40);
+
/* set irq0-7 to edge */
write_mmcr_byte(SC520_MPICMODE, 0x00);
-
+
/* set irq9-12 to level, all the other (8, 13-15) are edge */
write_mmcr_byte(SC520_SL1PICMODE, 0x1e);
-
+
/* set irq16-24 (unused slave pic2) to level */
write_mmcr_byte(SC520_SL2PICMODE, 0xff);
-
- /* active low polarity on PIC interrupt pins,
+
+ /* active low polarity on PIC interrupt pins,
active high polarity on all other irq pins */
write_mmcr_word(SC520_INTPINPOL, 0);
/* set irq number mapping */
- write_mmcr_byte(SC520_GPTMR0MAP,0); /* disable GP timer 0 INT */
+ write_mmcr_byte(SC520_GPTMR0MAP,0); /* disable GP timer 0 INT */
write_mmcr_byte(SC520_GPTMR1MAP,0); /* disable GP timer 1 INT */
write_mmcr_byte(SC520_GPTMR2MAP,0); /* disable GP timer 2 INT */
- write_mmcr_byte(SC520_PIT0MAP,0x1); /* Set PIT timer 0 INT to IRQ0 */
+ write_mmcr_byte(SC520_PIT0MAP,0x1); /* Set PIT timer 0 INT to IRQ0 */
write_mmcr_byte(SC520_PIT1MAP,0); /* diable PIT timer 1 INT */
write_mmcr_byte(SC520_PIT2MAP,0); /* diable PIT timer 2 INT */
write_mmcr_byte(SC520_PCIINTAMAP,0x4); /* Set PCI INT A to IRQ9 */
write_mmcr_byte(SC520_PCIINTBMAP,0x5); /* Set PCI INT B to IRQ10 */
write_mmcr_byte(SC520_PCIINTCMAP,0x6); /* Set PCI INT C to IRQ11 */
write_mmcr_byte(SC520_PCIINTDMAP,0x7); /* Set PCI INT D to IRQ12 */
- write_mmcr_byte(SC520_DMABCINTMAP,0); /* disable DMA INT */
+ write_mmcr_byte(SC520_DMABCINTMAP,0); /* disable DMA INT */
write_mmcr_byte(SC520_SSIMAP,0); /* disable Synchronius serial INT */
write_mmcr_byte(SC520_WDTMAP,0); /* disable Watchdor INT */
write_mmcr_byte(SC520_RTCMAP,0x3); /* Set RTC int to 8 */
@@ -69,28 +69,28 @@
write_mmcr_byte(SC520_GP0IMAP,6); /* Set GPIRQ0 (ISA IRQ2) to IRQ9 */
write_mmcr_byte(SC520_GP1IMAP,2); /* Set GPIRQ1 (SIO IRQ1) to IRQ1 */
write_mmcr_byte(SC520_GP2IMAP,7); /* Set GPIRQ2 (ISA IRQ12) to IRQ12 */
-
+
if (CFG_USE_SIO_UART) {
write_mmcr_byte(SC520_UART1MAP,0); /* disable internal UART1 INT */
write_mmcr_byte(SC520_UART2MAP,0); /* disable internal UART2 INT */
- write_mmcr_byte(SC520_GP3IMAP,11); /* Set GPIRQ3 (ISA IRQ3) to IRQ3 */
+ write_mmcr_byte(SC520_GP3IMAP,11); /* Set GPIRQ3 (ISA IRQ3) to IRQ3 */
write_mmcr_byte(SC520_GP4IMAP,12); /* Set GPIRQ4 (ISA IRQ4) to IRQ4 */
} else {
write_mmcr_byte(SC520_UART1MAP,12); /* Set internal UART2 INT to IRQ4 */
write_mmcr_byte(SC520_UART2MAP,11); /* Set internal UART2 INT to IRQ3 */
- write_mmcr_byte(SC520_GP3IMAP,0); /* disable GPIRQ3 (ISA IRQ3) */
+ write_mmcr_byte(SC520_GP3IMAP,0); /* disable GPIRQ3 (ISA IRQ3) */
write_mmcr_byte(SC520_GP4IMAP,0); /* disable GPIRQ4 (ISA IRQ4) */
}
-
+
write_mmcr_byte(SC520_GP5IMAP,13); /* Set GPIRQ5 (ISA IRQ5) to IRQ5 */
write_mmcr_byte(SC520_GP6IMAP,21); /* Set GPIRQ6 (ISA IRQ6) to IRQ6 */
write_mmcr_byte(SC520_GP7IMAP,22); /* Set GPIRQ7 (ISA IRQ7) to IRQ7 */
write_mmcr_byte(SC520_GP8IMAP,3); /* Set GPIRQ8 (SIO IRQ8) to IRQ8 */
write_mmcr_byte(SC520_GP9IMAP,4); /* Set GPIRQ9 (ISA IRQ9) to IRQ9 */
- write_mmcr_byte(SC520_GP10IMAP,9); /* Set GPIRQ10 (ISA IRQ10) to IRQ10 */
+ write_mmcr_byte(SC520_GP10IMAP,9); /* Set GPIRQ10 (ISA IRQ10) to IRQ10 */
write_mmcr_word(SC520_PCIHOSTMAP,0x11f); /* Map PCI hostbridge INT to NMI */
write_mmcr_word(SC520_ECCMAP,0x100); /* Map SDRAM ECC failure INT to NMI */
-
+
}
/* PCI stuff */
@@ -98,11 +98,11 @@
{
char pin;
int irq;
-
-
+
+
pci_hose_read_config_byte(hose, dev, PCI_INTERRUPT_PIN, &pin);
irq = pin-1;
-
+
switch (PCI_DEV(dev)) {
case 20:
break;
@@ -115,25 +115,25 @@
case 17:
irq+=3;
break;
- default:
+ default:
return;
}
-
+
irq&=3; /* wrap around */
irq+=9; /* lowest IRQ is 9 */
-
+
pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, irq);
-#if 0
- printf("fixup_irq: device %d pin %c irq %d\n",
+#if 0
+ printf("fixup_irq: device %d pin %c irq %d\n",
PCI_DEV(dev), 'A' + pin -1, irq);
#endif
}
-
+
static struct pci_controller sc520_cdp_hose = {
fixup_irq: pci_sc520_cdp_fixup_irq,
};
-void pci_init(void)
+void pci_init_board(void)
{
pci_sc520_init(&sc520_cdp_hose);
}
@@ -147,7 +147,7 @@
void setup_ali_sio(int uart_primary)
{
ali512x_init();
-
+
ali512x_set_fdc(ALI_ENABLED, 0x3f2, 6, 0);
ali512x_set_pp(ALI_ENABLED, 0x278, 7, 3);
ali512x_set_uart(ALI_ENABLED, ALI_UART1, uart_primary?0x3f8:0x3e8, 4);
@@ -155,21 +155,21 @@
ali512x_set_rtc(ALI_DISABLED, 0, 0);
ali512x_set_kbc(ALI_ENABLED, 1, 12);
ali512x_set_cio(ALI_ENABLED);
-
+
/* IrDa pins */
ali512x_cio_function(12, 1, 0, 0);
ali512x_cio_function(13, 1, 0, 0);
-
+
/* SSI chip select pins */
ali512x_cio_function(14, 0, 0, 0); /* SSI_CS */
- ali512x_cio_function(15, 0, 0, 0); /* SSI_MV */
+ ali512x_cio_function(15, 0, 0, 0); /* SSI_MV */
ali512x_cio_function(16, 0, 1, 0); /* SSI_SPI# (inverted) */
/* Board REV pins */
ali512x_cio_function(20, 0, 0, 1);
ali512x_cio_function(21, 0, 0, 1);
ali512x_cio_function(22, 0, 0, 1);
- ali512x_cio_function(23, 0, 0, 1);
+ ali512x_cio_function(23, 0, 0, 1);
}
@@ -178,13 +178,13 @@
{
/* set up the GP IO pins */
- write_mmcr_word(SC520_PIOPFS31_16, 0xf7ff); /* set the GPIO pin function 31-16 reg */
+ write_mmcr_word(SC520_PIOPFS31_16, 0xf7ff); /* set the GPIO pin function 31-16 reg */
write_mmcr_word(SC520_PIOPFS15_0, 0xffff); /* set the GPIO pin function 15-0 reg */
- write_mmcr_byte(SC520_CSPFS, 0xf8); /* set the CS pin function reg */
+ write_mmcr_byte(SC520_CSPFS, 0xf8); /* set the CS pin function reg */
write_mmcr_byte(SC520_CLKSEL, 0x70);
+
-
- write_mmcr_byte(SC520_GPCSRT, 1); /* set the GP CS offset */
+ write_mmcr_byte(SC520_GPCSRT, 1); /* set the GP CS offset */
write_mmcr_byte(SC520_GPCSPW, 3); /* set the GP CS pulse width */
write_mmcr_byte(SC520_GPCSOFF, 1); /* set the GP CS offset */
write_mmcr_byte(SC520_GPRDW, 3); /* set the RD pulse width */
@@ -192,40 +192,40 @@
write_mmcr_byte(SC520_GPWRW, 3); /* set the GP WR pulse width */
write_mmcr_byte(SC520_GPWROFF, 1); /* set the GP WR offset */
- write_mmcr_word(SC520_BOOTCSCTL, 0x1823); /* set up timing of BOOTCS */
+ write_mmcr_word(SC520_BOOTCSCTL, 0x1823); /* set up timing of BOOTCS */
write_mmcr_word(SC520_ROMCS1CTL, 0x1823); /* set up timing of ROMCS1 */
- write_mmcr_word(SC520_ROMCS2CTL, 0x1823); /* set up timing of ROMCS2 */
-
+ write_mmcr_word(SC520_ROMCS2CTL, 0x1823); /* set up timing of ROMCS2 */
+
/* adjust the memory map:
* by default the first 256MB (0x00000000 - 0x0fffffff) is mapped to SDRAM
* and 256MB to 1G-128k (0x1000000 - 0x37ffffff) is mapped to PCI mmio
- * we need to map 1G-128k - 1G (0x38000000 - 0x3fffffff) to CS1 */
-
-
+ * we need to map 1G-128k - 1G (0x38000000 - 0x3fffffff) to CS1 */
+
+
/* SRAM = GPCS3 128k @ d0000-effff*/
- write_mmcr_long(SC520_PAR2, 0x4e00400d);
-
+ write_mmcr_long(SC520_PAR2, 0x4e00400d);
+
/* IDE0 = GPCS6 1f0-1f7 */
- write_mmcr_long(SC520_PAR3, 0x380801f0);
+ write_mmcr_long(SC520_PAR3, 0x380801f0);
/* IDE1 = GPCS7 3f6 */
- write_mmcr_long(SC520_PAR4, 0x3c0003f6);
+ write_mmcr_long(SC520_PAR4, 0x3c0003f6);
/* bootcs */
- write_mmcr_long(SC520_PAR12, 0x8bffe800);
+ write_mmcr_long(SC520_PAR12, 0x8bffe800);
/* romcs2 */
- write_mmcr_long(SC520_PAR13, 0xcbfff000);
+ write_mmcr_long(SC520_PAR13, 0xcbfff000);
/* romcs1 */
- write_mmcr_long(SC520_PAR14, 0xabfff800);
+ write_mmcr_long(SC520_PAR14, 0xabfff800);
/* 680 LEDS */
- write_mmcr_long(SC520_PAR15, 0x30000640);
-
- asm ("wbinvd\n"); /* Flush cache, req. after setting the unchached attribute ona PAR */
+ write_mmcr_long(SC520_PAR15, 0x30000640);
+
+ asm ("wbinvd\n"); /* Flush cache, req. after setting the unchached attribute ona PAR */
if (CFG_USE_SIO_UART) {
- write_mmcr_byte(SC520_ADDDECCTL, read_mmcr_byte(SC520_ADDDECCTL) | UART2_DIS|UART1_DIS);
+ write_mmcr_byte(SC520_ADDDECCTL, read_mmcr_byte(SC520_ADDDECCTL) | UART2_DIS|UART1_DIS);
setup_ali_sio(1);
} else {
- write_mmcr_byte(SC520_ADDDECCTL, read_mmcr_byte(SC520_ADDDECCTL) & ~(UART2_DIS|UART1_DIS));
+ write_mmcr_byte(SC520_ADDDECCTL, read_mmcr_byte(SC520_ADDDECCTL) & ~(UART2_DIS|UART1_DIS));
setup_ali_sio(0);
silence_uart(0x3e8);
silence_uart(0x2e8);
@@ -242,21 +242,21 @@
int board_init(void)
{
DECLARE_GLOBAL_DATA_PTR;
-
- init_sc520();
+
+ init_sc520();
bus_init();
irq_init();
-
+
/* max drive current on SDRAM */
write_mmcr_word(SC520_DSCTL, 0x0100);
-
+
/* enter debug mode after next reset (only if jumper is also set) */
write_mmcr_byte(SC520_RESCFG, 0x08);
-
+
/* configure the software timer to 33.333MHz */
write_mmcr_byte(SC520_SWTMRCFG, 0);
gd->bus_clk = 33333000;
-
+
return 0;
}
@@ -277,14 +277,14 @@
{
int minor;
int major;
-
+
major = minor = 0;
major |= ali512x_cio_in(23)?2:0;
major |= ali512x_cio_in(22)?1:0;
minor |= ali512x_cio_in(21)?2:0;
minor |= ali512x_cio_in(20)?1:0;
-
+
printf("AMD SC520 CDP revision %d.%d\n", major, minor);
-
+
return 0;
}
diff --git a/board/utx8245/utx8245.c b/board/utx8245/utx8245.c
index 249862a..63b4e3e 100644
--- a/board/utx8245/utx8245.c
+++ b/board/utx8245/utx8245.c
@@ -143,7 +143,7 @@
#endif /*CONFIG_PCI_PNP*/
};
-void pci_init (void)
+void pci_init_board (void)
{
pci_mpc824x_init(&utx8245_hose);
diff --git a/common/env_common.c b/common/env_common.c
index 4f618d6..ea08501 100644
--- a/common/env_common.c
+++ b/common/env_common.c
@@ -128,6 +128,9 @@
#ifdef CONFIG_CLOCKS_IN_MHZ
"clocks_in_mhz=1\0"
#endif
+#if defined(CONFIG_PCI_BOOTDELAY) && (CONFIG_PCI_BOOTDELAY > 0)
+ "pcidelay=" MK_STR(CONFIG_PCI_BOOTDELAY) "\0"
+#endif
#ifdef CONFIG_EXTRA_ENV_SETTINGS
CONFIG_EXTRA_ENV_SETTINGS
#endif
diff --git a/common/environment.c b/common/environment.c
index 1df3872..244c2a2 100644
--- a/common/environment.c
+++ b/common/environment.c
@@ -164,6 +164,9 @@
#ifdef CONFIG_CLOCKS_IN_MHZ
"clocks_in_mhz=" "1" "\0"
#endif
+#if defined(CONFIG_PCI_BOOTDELAY) && (CONFIG_PCI_BOOTDELAY > 0)
+ "pcidelay=" MK_STR(CONFIG_PCI_BOOTDELAY) "\0"
+#endif
#ifdef CONFIG_EXTRA_ENV_SETTINGS
CONFIG_EXTRA_ENV_SETTINGS
#endif
diff --git a/cpu/ppc4xx/405gp_pci.c b/cpu/ppc4xx/405gp_pci.c
index 1c2c59b..fbd4d6d 100644
--- a/cpu/ppc4xx/405gp_pci.c
+++ b/cpu/ppc4xx/405gp_pci.c
@@ -376,7 +376,7 @@
config_table: pci_405gp_config_table,
};
-void pci_init(void)
+void pci_init_board(void)
{
/*we want the ptrs to RAM not flash (ie don't use init list)*/
hose.fixup_irq = pci_405gp_fixup_irq;
@@ -494,7 +494,7 @@
}
-void pci_init(void)
+void pci_init_board(void)
{
pci_440_init (&ppc440_hose);
}
diff --git a/drivers/pci.c b/drivers/pci.c
index dc58abf..9eaaa15 100644
--- a/drivers/pci.c
+++ b/drivers/pci.c
@@ -505,4 +505,23 @@
return pci_hose_scan_bus(hose, hose->first_busno);
}
+void pci_init(void)
+{
+#if defined(CONFIG_PCI_BOOTDELAY)
+ char *s;
+ int i;
+
+ /* wait "pcidelay" ms (if defined)... */
+ s = getenv ("pcidelay");
+ if (s) {
+ int val = simple_strtoul (s, NULL, 10);
+ for (i=0; i<val; i++)
+ udelay (1000);
+ }
+#endif /* CONFIG_PCI_BOOTDELAY */
+
+ /* now call board specific pci_init()... */
+ pci_init_board();
+}
+
#endif /* CONFIG_PCI */
diff --git a/include/common.h b/include/common.h
index d9d5702..9f22b2f 100644
--- a/include/common.h
+++ b/include/common.h
@@ -149,10 +149,11 @@
# include <asm/u-boot-arm.h> /* ARM version to be fixed! */
#endif /* CONFIG_ARM */
#ifdef CONFIG_I386 /* x86 version to be fixed! */
-# include <asm/ppcboot-i386.h>
+# include <asm/ppcboot-i386.h>
#endif /* CONFIG_I386 */
void pci_init (void);
+void pci_init_board(void);
void pciinfo (int, int);
#if defined(CONFIG_PCI) && defined(CONFIG_440)
diff --git a/include/configs/AR405.h b/include/configs/AR405.h
index 56bb15b..acb2fb6 100644
--- a/include/configs/AR405.h
+++ b/include/configs/AR405.h
@@ -122,6 +122,10 @@
#define CONFIG_PCI_PNP /* do pci plug-and-play */
/* resource configuration */
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+
+#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
+
#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
#define CFG_PCI_SUBSYS_DEVICEID 0x0403 /* PCI Device ID: ARISTO405 */
#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
diff --git a/include/configs/CPCI405.h b/include/configs/CPCI405.h
index 6b98347..845b47b 100644
--- a/include/configs/CPCI405.h
+++ b/include/configs/CPCI405.h
@@ -74,6 +74,7 @@
CFG_CMD_IRQ | \
CFG_CMD_IDE | \
CFG_CMD_ELF | \
+ CFG_CMD_MII | \
CFG_CMD_EEPROM )
#define CONFIG_MAC_PARTITION
@@ -144,6 +145,8 @@
#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
+
#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */
diff --git a/include/configs/CPCI4052.h b/include/configs/CPCI4052.h
index 0533827..18cec98 100644
--- a/include/configs/CPCI4052.h
+++ b/include/configs/CPCI4052.h
@@ -80,6 +80,7 @@
CFG_CMD_DATE | \
CFG_CMD_JFFS2 | \
CFG_CMD_I2C | \
+ CFG_CMD_MII | \
CFG_CMD_EEPROM )
#define CONFIG_MAC_PARTITION
@@ -150,6 +151,8 @@
#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
+
#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */
diff --git a/include/configs/CPCI440.h b/include/configs/CPCI440.h
index 04ce99d..55bb1ec 100644
--- a/include/configs/CPCI440.h
+++ b/include/configs/CPCI440.h
@@ -237,6 +237,10 @@
#define CONFIG_PCI_PNP /* do pci plug-and-play */
/* resource configuration */
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+
+#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
+
#define CFG_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */
#define CFG_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */
#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
diff --git a/include/configs/DU405.h b/include/configs/DU405.h
index 1bf40d9..bac6221 100644
--- a/include/configs/DU405.h
+++ b/include/configs/DU405.h
@@ -120,6 +120,10 @@
#define CONFIG_PCI_PNP /* do pci plug-and-play */
/* resource configuration */
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+
+#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
+
#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
#define CFG_PCI_SUBSYS_DEVICEID 0x0404 /* PCI Device ID: CPCI-ISER4 */
#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
diff --git a/include/configs/OCRTC.h b/include/configs/OCRTC.h
index 5971fb4..0ac456a 100644
--- a/include/configs/OCRTC.h
+++ b/include/configs/OCRTC.h
@@ -120,6 +120,8 @@
#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
+
#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
#define CFG_PCI_SUBSYS_DEVICEID 0x0410 /* PCI Device ID: OCRTC */
#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
diff --git a/tools/env/fw_env.c b/tools/env/fw_env.c
index 87b41ea..de10b02 100644
--- a/tools/env/fw_env.c
+++ b/tools/env/fw_env.c
@@ -142,6 +142,9 @@
#ifdef CONFIG_CLOCKS_IN_MHZ
"clocks_in_mhz=" "1" "\0"
#endif
+#if defined(CONFIG_PCI_BOOTDELAY) && (CONFIG_PCI_BOOTDELAY > 0)
+ "pcidelay=" MK_STR(CONFIG_PCI_BOOTDELAY) "\0"
+#endif
#ifdef CONFIG_EXTRA_ENV_SETTINGS
CONFIG_EXTRA_ENV_SETTINGS
#endif
@@ -387,8 +390,8 @@
char *data;
if ((fd = open(DEVNAME(curdev), mode)) < 0) {
- fprintf (stderr,
- "Can't open %s: %s\n",
+ fprintf (stderr,
+ "Can't open %s: %s\n",
DEVNAME(curdev), strerror(errno));
return (-1);
}
@@ -403,8 +406,8 @@
/* switch to next partition for writing */
otherdev = !curdev;
if ((fdr = open(DEVNAME(otherdev), mode)) < 0) {
- fprintf (stderr,
- "Can't open %s: %s\n",
+ fprintf (stderr,
+ "Can't open %s: %s\n",
DEVNAME(otherdev), strerror(errno));
return (-1);
}
@@ -428,20 +431,20 @@
resid = DEVESIZE(otherdev) - CFG_ENV_SIZE;
if (resid) {
if ((data = malloc(resid)) == NULL) {
- fprintf(stderr,
+ fprintf(stderr,
"Cannot malloc %d bytes: %s\n",
resid, strerror(errno));
return (-1);
}
if (lseek (fdr, DEVOFFSET(otherdev) + CFG_ENV_SIZE, SEEK_SET) == -1) {
fprintf (stderr,
- "seek error on %s: %s\n",
+ "seek error on %s: %s\n",
DEVNAME(otherdev), strerror(errno));
return (-1);
}
if ((rc = read (fdr, data, resid)) != resid) {
fprintf (stderr,
- "read error on %s: %s\n",
+ "read error on %s: %s\n",
DEVNAME(otherdev), strerror(errno));
return (-1);
}
@@ -462,26 +465,26 @@
printf("Writing environment to %s...\n",DEVNAME(otherdev));
if (lseek (fdr, DEVOFFSET(otherdev), SEEK_SET) == -1) {
fprintf (stderr,
- "seek error on %s: %s\n",
+ "seek error on %s: %s\n",
DEVNAME(otherdev), strerror(errno));
return (-1);
}
if (write(fdr, &environment, len) != len) {
fprintf (stderr,
- "CRC write error on %s: %s\n",
+ "CRC write error on %s: %s\n",
DEVNAME(otherdev), strerror(errno));
return (-1);
}
if (write(fdr, environment.data, ENV_SIZE) != ENV_SIZE) {
fprintf (stderr,
- "Write error on %s: %s\n",
+ "Write error on %s: %s\n",
DEVNAME(otherdev), strerror(errno));
return (-1);
}
if (resid) {
if (write (fdr, data, resid) != resid) {
fprintf (stderr,
- "write error on %s: %s\n",
+ "write error on %s: %s\n",
DEVNAME(curdev), strerror(errno));
return (-1);
}
@@ -491,14 +494,14 @@
/* change flag on current active env partition */
if (lseek (fd, DEVOFFSET(curdev) + sizeof(ulong), SEEK_SET) == -1) {
fprintf (stderr,
- "seek error on %s: %s\n",
+ "seek error on %s: %s\n",
DEVNAME(curdev), strerror(errno));
return (-1);
}
- if (write (fd, &obsolete_flag, sizeof(obsolete_flag)) !=
+ if (write (fd, &obsolete_flag, sizeof(obsolete_flag)) !=
sizeof(obsolete_flag)) {
fprintf (stderr,
- "Write error on %s: %s\n",
+ "Write error on %s: %s\n",
DEVNAME(curdev), strerror(errno));
return (-1);
}
@@ -514,7 +517,7 @@
ioctl (fd, MEMLOCK, &erase);
if (close(fdr)) {
fprintf (stderr,
- "I/O error on %s: %s\n",
+ "I/O error on %s: %s\n",
DEVNAME(otherdev), strerror(errno));
return (-1);
}
@@ -524,19 +527,19 @@
if (lseek (fd, DEVOFFSET(curdev), SEEK_SET) == -1) {
fprintf (stderr,
- "seek error on %s: %s\n",
+ "seek error on %s: %s\n",
DEVNAME(curdev), strerror(errno));
return (-1);
}
if (read (fd, &environment, len) != len) {
fprintf (stderr,
- "CRC read error on %s: %s\n",
+ "CRC read error on %s: %s\n",
DEVNAME(curdev), strerror(errno));
return (-1);
}
if ((rc = read (fd, environment.data, ENV_SIZE)) != ENV_SIZE) {
fprintf (stderr,
- "Read error on %s: %s\n",
+ "Read error on %s: %s\n",
DEVNAME(curdev), strerror(errno));
return (-1);
}
@@ -544,7 +547,7 @@
if (close(fd)) {
fprintf (stderr,
- "I/O error on %s: %s\n",
+ "I/O error on %s: %s\n",
DEVNAME(curdev), strerror(errno));
return (-1);
}
@@ -584,50 +587,50 @@
if (parse_config()) /* should fill envdevices */
return 1;
-
+
if ((addr1 = calloc (1, ENV_SIZE)) == NULL) {
- fprintf (stderr,
+ fprintf (stderr,
"Not enough memory for environment (%ld bytes)\n",
ENV_SIZE);
return (errno);
}
-
+
/* read environment from FLASH to local buffer */
environment.data = addr1;
curdev = 0;
if (flash_io (O_RDONLY)) {
return (errno);
}
-
- crc1_ok = ((crc1 = crc32(0, environment.data, ENV_SIZE))
+
+ crc1_ok = ((crc1 = crc32(0, environment.data, ENV_SIZE))
== environment.crc);
if (!HaveRedundEnv) {
if (!crc1_ok) {
- fprintf (stderr,
+ fprintf (stderr,
"Warning: Bad CRC, using default environment\n");
environment.data = default_environment;
free(addr1);
}
} else {
flag1 = environment.flags;
-
+
curdev = 1;
if ((addr2 = calloc (1, ENV_SIZE)) == NULL) {
- fprintf (stderr,
+ fprintf (stderr,
"Not enough memory for environment (%ld bytes)\n",
ENV_SIZE);
return (errno);
- }
+ }
environment.data = addr2;
-
+
if (flash_io (O_RDONLY)) {
return (errno);
}
-
- crc2_ok = ((crc2 = crc32(0, environment.data, ENV_SIZE))
+
+ crc2_ok = ((crc2 = crc32(0, environment.data, ENV_SIZE))
== environment.crc);
flag2 = environment.flags;
-
+
if (crc1_ok && ! crc2_ok) {
environment.data = addr1;
environment.flags = flag1;
@@ -643,7 +646,7 @@
free(addr1);
}
else if (! crc1_ok && ! crc2_ok) {
- fprintf (stderr,
+ fprintf (stderr,
"Warning: Bad CRC, using default environment\n");
environment.data = default_environment;
curdev = 0;
@@ -717,15 +720,15 @@
#endif
#endif
if (stat (DEVNAME(0), &st)) {
- fprintf (stderr,
- "Cannot access MTD device %s: %s\n",
+ fprintf (stderr,
+ "Cannot access MTD device %s: %s\n",
DEVNAME(0), strerror(errno));
return 1;
}
-
+
if (HaveRedundEnv && stat (DEVNAME(1), &st)) {
- fprintf (stderr,
- "Cannot access MTD device %s: %s\n",
+ fprintf (stderr,
+ "Cannot access MTD device %s: %s\n",
DEVNAME(2), strerror(errno));
return 1;
}
@@ -744,12 +747,12 @@
return 1;
}
- while ((i < 2) &&
+ while ((i < 2) &&
((rc = fscanf (fp, "%s %lx %lx %lx",
DEVNAME(i), &DEVOFFSET(i), &ENVSIZE(i), &DEVESIZE(i))) != EOF)) {
/* Skip incomplete conversions and comment strings */
- if ((rc < 3) || (*DEVNAME(i) == '#')) {
+ if ((rc < 3) || (*DEVNAME(i) == '#')) {
fgets (dump, sizeof(dump), fp); /* Consume till end */
continue;
}
@@ -757,7 +760,7 @@
i++;
}
fclose(fp);
-
+
HaveRedundEnv = i - 1;
if (!i) { /* No valid entries found */
errno = EINVAL;