mmc: stm32_sdmmc2: remove privdata
All the elements of privdata are static and build from device tree,
they are moved in platdata to prepare the support of ops
of_to_plat.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
diff --git a/drivers/mmc/stm32_sdmmc2.c b/drivers/mmc/stm32_sdmmc2.c
index e3853b7..41f375b 100644
--- a/drivers/mmc/stm32_sdmmc2.c
+++ b/drivers/mmc/stm32_sdmmc2.c
@@ -30,9 +30,6 @@
struct stm32_sdmmc2_plat {
struct mmc_config cfg;
struct mmc mmc;
-};
-
-struct stm32_sdmmc2_priv {
fdt_addr_t base;
struct clk clk;
struct reset_ctl reset_ctl;
@@ -208,7 +205,7 @@
struct mmc_data *data,
struct stm32_sdmmc2_ctx *ctx)
{
- struct stm32_sdmmc2_priv *priv = dev_get_priv(dev);
+ struct stm32_sdmmc2_plat *plat = dev_get_plat(dev);
u32 data_ctrl, idmabase0;
/* Configure the SDMMC DPSM (Data Path State Machine) */
@@ -224,10 +221,10 @@
}
/* Set the SDMMC DataLength value */
- writel(ctx->data_length, priv->base + SDMMC_DLEN);
+ writel(ctx->data_length, plat->base + SDMMC_DLEN);
/* Write to SDMMC DCTRL */
- writel(data_ctrl, priv->base + SDMMC_DCTRL);
+ writel(data_ctrl, plat->base + SDMMC_DCTRL);
/* Cache align */
ctx->cache_start = rounddown(idmabase0, ARCH_DMA_MINALIGN);
@@ -242,19 +239,19 @@
flush_dcache_range(ctx->cache_start, ctx->cache_end);
/* Enable internal DMA */
- writel(idmabase0, priv->base + SDMMC_IDMABASE0);
- writel(SDMMC_IDMACTRL_IDMAEN, priv->base + SDMMC_IDMACTRL);
+ writel(idmabase0, plat->base + SDMMC_IDMABASE0);
+ writel(SDMMC_IDMACTRL_IDMAEN, plat->base + SDMMC_IDMACTRL);
}
static void stm32_sdmmc2_start_cmd(struct udevice *dev,
struct mmc_cmd *cmd, u32 cmd_param,
struct stm32_sdmmc2_ctx *ctx)
{
- struct stm32_sdmmc2_priv *priv = dev_get_priv(dev);
+ struct stm32_sdmmc2_plat *plat = dev_get_plat(dev);
u32 timeout = 0;
- if (readl(priv->base + SDMMC_CMD) & SDMMC_CMD_CPSMEN)
- writel(0, priv->base + SDMMC_CMD);
+ if (readl(plat->base + SDMMC_CMD) & SDMMC_CMD_CPSMEN)
+ writel(0, plat->base + SDMMC_CMD);
cmd_param |= cmd->cmdidx | SDMMC_CMD_CPSMEN;
if (cmd->resp_type & MMC_RSP_PRESENT) {
@@ -277,30 +274,30 @@
if (ctx->data_length) {
timeout = SDMMC_CMD_TIMEOUT;
} else {
- writel(0, priv->base + SDMMC_DCTRL);
+ writel(0, plat->base + SDMMC_DCTRL);
if (cmd->resp_type & MMC_RSP_BUSY)
timeout = SDMMC_CMD_TIMEOUT;
}
/* Set the SDMMC Data TimeOut value */
- writel(timeout, priv->base + SDMMC_DTIMER);
+ writel(timeout, plat->base + SDMMC_DTIMER);
/* Clear flags */
- writel(SDMMC_ICR_STATIC_FLAGS, priv->base + SDMMC_ICR);
+ writel(SDMMC_ICR_STATIC_FLAGS, plat->base + SDMMC_ICR);
/* Set SDMMC argument value */
- writel(cmd->cmdarg, priv->base + SDMMC_ARG);
+ writel(cmd->cmdarg, plat->base + SDMMC_ARG);
/* Set SDMMC command parameters */
- writel(cmd_param, priv->base + SDMMC_CMD);
+ writel(cmd_param, plat->base + SDMMC_CMD);
}
static int stm32_sdmmc2_end_cmd(struct udevice *dev,
struct mmc_cmd *cmd,
struct stm32_sdmmc2_ctx *ctx)
{
- struct stm32_sdmmc2_priv *priv = dev_get_priv(dev);
+ struct stm32_sdmmc2_plat *plat = dev_get_plat(dev);
u32 mask = SDMMC_STA_CTIMEOUT;
u32 status;
int ret;
@@ -314,7 +311,7 @@
}
/* Polling status register */
- ret = readl_poll_timeout(priv->base + SDMMC_STA, status, status & mask,
+ ret = readl_poll_timeout(plat->base + SDMMC_STA, status, status & mask,
10000);
if (ret < 0) {
@@ -339,11 +336,11 @@
}
if (status & SDMMC_STA_CMDREND && cmd->resp_type & MMC_RSP_PRESENT) {
- cmd->response[0] = readl(priv->base + SDMMC_RESP1);
+ cmd->response[0] = readl(plat->base + SDMMC_RESP1);
if (cmd->resp_type & MMC_RSP_136) {
- cmd->response[1] = readl(priv->base + SDMMC_RESP2);
- cmd->response[2] = readl(priv->base + SDMMC_RESP3);
- cmd->response[3] = readl(priv->base + SDMMC_RESP4);
+ cmd->response[1] = readl(plat->base + SDMMC_RESP2);
+ cmd->response[2] = readl(plat->base + SDMMC_RESP3);
+ cmd->response[3] = readl(plat->base + SDMMC_RESP4);
}
/* Wait for BUSYD0END flag if busy status is detected */
@@ -352,7 +349,7 @@
mask = SDMMC_STA_DTIMEOUT | SDMMC_STA_BUSYD0END;
/* Polling status register */
- ret = readl_poll_timeout(priv->base + SDMMC_STA,
+ ret = readl_poll_timeout(plat->base + SDMMC_STA,
status, status & mask,
SDMMC_BUSYD0END_TIMEOUT_US);
@@ -380,7 +377,7 @@
struct mmc_data *data,
struct stm32_sdmmc2_ctx *ctx)
{
- struct stm32_sdmmc2_priv *priv = dev_get_priv(dev);
+ struct stm32_sdmmc2_plat *plat = dev_get_plat(dev);
u32 mask = SDMMC_STA_DCRCFAIL | SDMMC_STA_DTIMEOUT |
SDMMC_STA_IDMATE | SDMMC_STA_DATAEND;
u32 status;
@@ -390,9 +387,9 @@
else
mask |= SDMMC_STA_TXUNDERR;
- status = readl(priv->base + SDMMC_STA);
+ status = readl(plat->base + SDMMC_STA);
while (!(status & mask))
- status = readl(priv->base + SDMMC_STA);
+ status = readl(plat->base + SDMMC_STA);
/*
* Need invalidate the dcache again to avoid any
@@ -404,7 +401,7 @@
if (status & SDMMC_STA_DCRCFAIL) {
dev_dbg(dev, "error SDMMC_STA_DCRCFAIL (0x%x) for cmd %d\n",
status, cmd->cmdidx);
- if (readl(priv->base + SDMMC_DCOUNT))
+ if (readl(plat->base + SDMMC_DCOUNT))
ctx->dpsm_abort = true;
return -EILSEQ;
}
@@ -443,7 +440,7 @@
static int stm32_sdmmc2_send_cmd(struct udevice *dev, struct mmc_cmd *cmd,
struct mmc_data *data)
{
- struct stm32_sdmmc2_priv *priv = dev_get_priv(dev);
+ struct stm32_sdmmc2_plat *plat = dev_get_plat(dev);
struct stm32_sdmmc2_ctx ctx;
u32 cmdat = data ? SDMMC_CMD_CMDTRANS : 0;
int ret, retry = 3;
@@ -470,9 +467,9 @@
ret = stm32_sdmmc2_end_data(dev, cmd, data, &ctx);
/* Clear flags */
- writel(SDMMC_ICR_STATIC_FLAGS, priv->base + SDMMC_ICR);
+ writel(SDMMC_ICR_STATIC_FLAGS, plat->base + SDMMC_ICR);
if (data)
- writel(0x0, priv->base + SDMMC_IDMACTRL);
+ writel(0x0, plat->base + SDMMC_IDMACTRL);
/*
* To stop Data Path State Machine, a stop_transmission command
@@ -493,7 +490,7 @@
SDMMC_CMD_CMDSTOP, &ctx);
stm32_sdmmc2_end_cmd(dev, &stop_cmd, &ctx);
- writel(SDMMC_ICR_STATIC_FLAGS, priv->base + SDMMC_ICR);
+ writel(SDMMC_ICR_STATIC_FLAGS, plat->base + SDMMC_ICR);
}
if ((ret != -ETIMEDOUT) && (ret != 0) && retry) {
@@ -512,17 +509,17 @@
* This will reset the SDMMC to the reset state and the CPSM and DPSM
* to the Idle state. SDMMC is disabled, Signals Hiz.
*/
-static void stm32_sdmmc2_reset(struct stm32_sdmmc2_priv *priv)
+static void stm32_sdmmc2_reset(struct stm32_sdmmc2_plat *plat)
{
- if (reset_valid(&priv->reset_ctl)) {
+ if (reset_valid(&plat->reset_ctl)) {
/* Reset */
- reset_assert(&priv->reset_ctl);
+ reset_assert(&plat->reset_ctl);
udelay(2);
- reset_deassert(&priv->reset_ctl);
+ reset_deassert(&plat->reset_ctl);
}
/* init the needed SDMMC register after reset */
- writel(priv->pwr_reg_msk, priv->base + SDMMC_POWER);
+ writel(plat->pwr_reg_msk, plat->base + SDMMC_POWER);
}
/*
@@ -531,13 +528,13 @@
* SDMMC_CMD and SDMMC_CK are driven low, to prevent the card from being
* supplied through the signal lines.
*/
-static void stm32_sdmmc2_pwrcycle(struct stm32_sdmmc2_priv *priv)
+static void stm32_sdmmc2_pwrcycle(struct stm32_sdmmc2_plat *plat)
{
- if ((readl(priv->base + SDMMC_POWER) & SDMMC_POWER_PWRCTRL_MASK) ==
+ if ((readl(plat->base + SDMMC_POWER) & SDMMC_POWER_PWRCTRL_MASK) ==
SDMMC_POWER_PWRCTRL_CYCLE)
return;
- stm32_sdmmc2_reset(priv);
+ stm32_sdmmc2_reset(plat);
}
/*
@@ -546,10 +543,10 @@
* Reset => Power-Cycle => Power-Off => Power
* PWRCTRL=10 PWCTRL=00 PWCTRL=11
*/
-static void stm32_sdmmc2_pwron(struct stm32_sdmmc2_priv *priv)
+static void stm32_sdmmc2_pwron(struct stm32_sdmmc2_plat *plat)
{
u32 pwrctrl =
- readl(priv->base + SDMMC_POWER) & SDMMC_POWER_PWRCTRL_MASK;
+ readl(plat->base + SDMMC_POWER) & SDMMC_POWER_PWRCTRL_MASK;
if (pwrctrl == SDMMC_POWER_PWRCTRL_ON)
return;
@@ -558,21 +555,21 @@
* it is the reset state here = the only managed by the driver
*/
if (pwrctrl == SDMMC_POWER_PWRCTRL_OFF) {
- writel(SDMMC_POWER_PWRCTRL_CYCLE | priv->pwr_reg_msk,
- priv->base + SDMMC_POWER);
+ writel(SDMMC_POWER_PWRCTRL_CYCLE | plat->pwr_reg_msk,
+ plat->base + SDMMC_POWER);
}
/*
* the remaining case is SDMMC_POWER_PWRCTRL_CYCLE
* switch to Power-Off state: SDMCC disable, signals drive 1
*/
- writel(SDMMC_POWER_PWRCTRL_OFF | priv->pwr_reg_msk,
- priv->base + SDMMC_POWER);
+ writel(SDMMC_POWER_PWRCTRL_OFF | plat->pwr_reg_msk,
+ plat->base + SDMMC_POWER);
/* After the 1ms delay set the SDMMC to power-on */
mdelay(1);
- writel(SDMMC_POWER_PWRCTRL_ON | priv->pwr_reg_msk,
- priv->base + SDMMC_POWER);
+ writel(SDMMC_POWER_PWRCTRL_ON | plat->pwr_reg_msk,
+ plat->base + SDMMC_POWER);
/* during the first 74 SDMMC_CK cycles the SDMMC is still disabled. */
}
@@ -581,18 +578,18 @@
static int stm32_sdmmc2_set_ios(struct udevice *dev)
{
struct mmc *mmc = mmc_get_mmc_dev(dev);
- struct stm32_sdmmc2_priv *priv = dev_get_priv(dev);
+ struct stm32_sdmmc2_plat *plat = dev_get_plat(dev);
u32 desired = mmc->clock;
- u32 sys_clock = clk_get_rate(&priv->clk);
+ u32 sys_clock = clk_get_rate(&plat->clk);
u32 clk = 0;
dev_dbg(dev, "bus_with = %d, clock = %d\n",
mmc->bus_width, mmc->clock);
if (mmc->clk_disable)
- stm32_sdmmc2_pwrcycle(priv);
+ stm32_sdmmc2_pwrcycle(plat);
else
- stm32_sdmmc2_pwron(priv);
+ stm32_sdmmc2_pwron(plat);
/*
* clk_div = 0 => command and data generated on SDMMCCLK falling edge
@@ -602,7 +599,7 @@
* SDMMCCLK falling edge
*/
if (desired && ((sys_clock > desired) ||
- IS_RISING_EDGE(priv->clk_reg_msk))) {
+ IS_RISING_EDGE(plat->clk_reg_msk))) {
clk = DIV_ROUND_UP(sys_clock, 2 * desired);
if (clk > SDMMC_CLKCR_CLKDIV_MAX)
clk = SDMMC_CLKCR_CLKDIV_MAX;
@@ -613,30 +610,30 @@
if (mmc->bus_width == 8)
clk |= SDMMC_CLKCR_WIDBUS_8;
- writel(clk | priv->clk_reg_msk | SDMMC_CLKCR_HWFC_EN,
- priv->base + SDMMC_CLKCR);
+ writel(clk | plat->clk_reg_msk | SDMMC_CLKCR_HWFC_EN,
+ plat->base + SDMMC_CLKCR);
return 0;
}
static int stm32_sdmmc2_getcd(struct udevice *dev)
{
- struct stm32_sdmmc2_priv *priv = dev_get_priv(dev);
+ struct stm32_sdmmc2_plat *plat = dev_get_plat(dev);
dev_dbg(dev, "%s called\n", __func__);
- if (dm_gpio_is_valid(&priv->cd_gpio))
- return dm_gpio_get_value(&priv->cd_gpio);
+ if (dm_gpio_is_valid(&plat->cd_gpio))
+ return dm_gpio_get_value(&plat->cd_gpio);
return 1;
}
static int stm32_sdmmc2_host_power_cycle(struct udevice *dev)
{
- struct stm32_sdmmc2_priv *priv = dev_get_priv(dev);
+ struct stm32_sdmmc2_plat *plat = dev_get_plat(dev);
- writel(SDMMC_POWER_PWRCTRL_CYCLE | priv->pwr_reg_msk,
- priv->base + SDMMC_POWER);
+ writel(SDMMC_POWER_PWRCTRL_CYCLE | plat->pwr_reg_msk,
+ plat->base + SDMMC_POWER);
return 0;
}
@@ -650,7 +647,7 @@
static int stm32_sdmmc2_probe_level_translator(struct udevice *dev)
{
- struct stm32_sdmmc2_priv *priv = dev_get_priv(dev);
+ struct stm32_sdmmc2_plat *plat = dev_get_plat(dev);
struct gpio_desc cmd_gpio;
struct gpio_desc ck_gpio;
struct gpio_desc ckin_gpio;
@@ -660,7 +657,7 @@
* Assume the level translator is present if st,use-ckin is set.
* This is to cater for DTs which do not implement this test.
*/
- priv->clk_reg_msk |= SDMMC_CLKCR_SELCLKRX_CKIN;
+ plat->clk_reg_msk |= SDMMC_CLKCR_SELCLKRX_CKIN;
ret = gpio_request_by_name(dev, "st,cmd-gpios", 0, &cmd_gpio,
GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE);
@@ -694,7 +691,7 @@
/* Level translator is present if CK signal is propagated to CKIN */
if (!clk_hi || clk_lo)
- priv->clk_reg_msk &= ~SDMMC_CLKCR_SELCLKRX_CKIN;
+ plat->clk_reg_msk &= ~SDMMC_CLKCR_SELCLKRX_CKIN;
dm_gpio_free(dev, &ckin_gpio);
@@ -712,34 +709,33 @@
{
struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev);
struct stm32_sdmmc2_plat *plat = dev_get_plat(dev);
- struct stm32_sdmmc2_priv *priv = dev_get_priv(dev);
struct mmc_config *cfg = &plat->cfg;
int ret;
- priv->base = dev_read_addr(dev);
- if (priv->base == FDT_ADDR_T_NONE)
+ plat->base = dev_read_addr(dev);
+ if (plat->base == FDT_ADDR_T_NONE)
return -EINVAL;
if (dev_read_bool(dev, "st,neg-edge"))
- priv->clk_reg_msk |= SDMMC_CLKCR_NEGEDGE;
+ plat->clk_reg_msk |= SDMMC_CLKCR_NEGEDGE;
if (dev_read_bool(dev, "st,sig-dir"))
- priv->pwr_reg_msk |= SDMMC_POWER_DIRPOL;
+ plat->pwr_reg_msk |= SDMMC_POWER_DIRPOL;
if (dev_read_bool(dev, "st,use-ckin"))
stm32_sdmmc2_probe_level_translator(dev);
- ret = clk_get_by_index(dev, 0, &priv->clk);
+ ret = clk_get_by_index(dev, 0, &plat->clk);
if (ret)
return ret;
- ret = clk_enable(&priv->clk);
+ ret = clk_enable(&plat->clk);
if (ret)
goto clk_free;
- ret = reset_get_by_index(dev, 0, &priv->reset_ctl);
+ ret = reset_get_by_index(dev, 0, &plat->reset_ctl);
if (ret)
dev_dbg(dev, "No reset provided\n");
- gpio_request_by_name(dev, "cd-gpios", 0, &priv->cd_gpio,
+ gpio_request_by_name(dev, "cd-gpios", 0, &plat->cd_gpio,
GPIOD_IS_IN);
cfg->f_min = 400000;
@@ -754,11 +750,11 @@
upriv->mmc = &plat->mmc;
/* SDMMC init */
- stm32_sdmmc2_reset(priv);
+ stm32_sdmmc2_reset(plat);
return 0;
clk_free:
- clk_free(&priv->clk);
+ clk_free(&plat->clk);
return ret;
}
@@ -782,6 +778,5 @@
.ops = &stm32_sdmmc2_ops,
.probe = stm32_sdmmc2_probe,
.bind = stm32_sdmmc2_bind,
- .priv_auto = sizeof(struct stm32_sdmmc2_priv),
.plat_auto = sizeof(struct stm32_sdmmc2_plat),
};