Patch by Kenneth Johansson, 30 Jun 2003:
get rid of MK_CMD_ENTRY macro; update doc/README.command
diff --git a/common/cmd_load.c b/common/cmd_load.c
index 5272b0f..2cb2f33 100644
--- a/common/cmd_load.c
+++ b/common/cmd_load.c
@@ -971,8 +971,8 @@
#if (CONFIG_COMMANDS & CFG_CMD_LOADS)
#ifdef CFG_LOADS_BAUD_CHANGE
-cmd_tbl_t U_BOOT_CMD(LOADS) = MK_CMD_ENTRY(
- "loads", 3, 0, do_load_serial,
+U_BOOT_CMD(
+ loads, 3, 0, do_load_serial,
"loads - load S-Record file over serial line\n",
"[ off ] [ baud ]\n"
" - load S-Record file over serial line"
@@ -980,8 +980,8 @@
);
#else /* ! CFG_LOADS_BAUD_CHANGE */
-cmd_tbl_t U_BOOT_CMD(LOADS) = MK_CMD_ENTRY(
- "loads", 2, 0, do_load_serial,
+U_BOOT_CMD(
+ loads, 2, 0, do_load_serial,
"loads - load S-Record file over serial line\n",
"[ off ]\n"
" - load S-Record file over serial line with offset 'off'\n"
@@ -995,16 +995,16 @@
#if (CONFIG_COMMANDS & CFG_CMD_SAVES)
#ifdef CFG_LOADS_BAUD_CHANGE
-cmd_tbl_t U_BOOT_CMD(SAVES) = MK_CMD_ENTRY(
- "saves", 4, 0, do_save_serial,
+U_BOOT_CMD(
+ saves, 4, 0, do_save_serial,
"saves - save S-Record file over serial line\n",
"[ off ] [size] [ baud ]\n"
" - save S-Record file over serial line"
" with offset 'off', size 'size' and baudrate 'baud'\n"
);
#else /* ! CFG_LOADS_BAUD_CHANGE */
-cmd_tbl_t U_BOOT_CMD(SAVES) = MK_CMD_ENTRY(
- "saves", 3, 0, do_save_serial,
+U_BOOT_CMD(
+ saves, 3, 0, do_save_serial,
"saves - save S-Record file over serial line\n",
"[ off ] [size]\n"
" - save S-Record file over serial line with offset 'off' and size 'size'\n"
@@ -1015,8 +1015,8 @@
#if (CONFIG_COMMANDS & CFG_CMD_LOADB)
-cmd_tbl_t U_BOOT_CMD(LOADB) = MK_CMD_ENTRY(
- "loadb", 3, 0, do_load_serial_bin,
+U_BOOT_CMD(
+ loadb, 3, 0, do_load_serial_bin,
"loadb - load binary file over serial line (kermit mode)\n",
"[ off ] [ baud ]\n"
" - load binary file over serial line"
@@ -1047,8 +1047,8 @@
/* -------------------------------------------------------------------- */
-cmd_tbl_t U_BOOT_CMD(HWFLOW) = MK_CMD_ENTRY(
- "hwflow [on|off]", 2, 0, do_hwflow,
+U_BOOT_CMD(
+ hwflow [on|off], 2, 0, do_hwflow,
"hwflow - turn the harwdare flow control on/off\n",
"\n - change RTS/CTS hardware flow control over serial line\n"
);