diff --git a/MAINTAINERS b/MAINTAINERS
index 864a827..e42a327 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -742,6 +742,7 @@
 	km_kirkwood	ARM926EJS (Kirkwood SoC)
 	kmnusa		ARM926EJS (Kirkwood SoC)
 	mgcoge3un	ARM926EJS (Kirkwood SoC)
+	kmcoge5un	ARM926EJS (Kirkwood SoC)
 	portl2		ARM926EJS (Kirkwood SoC)
 
 Nishanth Menon <nm@ti.com>
diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c
index e77c5ad..73ddb61 100644
--- a/board/keymile/km_arm/km_arm.c
+++ b/board/keymile/km_arm/km_arm.c
@@ -457,7 +457,11 @@
 
 int post_hotkeys_pressed(void)
 {
+#if defined(CONFIG_KM_COGE5UN)
+	return kw_gpio_get_value(KM_POST_EN_L);
+#else
 	return !kw_gpio_get_value(KM_POST_EN_L);
+#endif
 }
 
 ulong post_word_load(void)
diff --git a/board/keymile/km_arm/kwbimage_256M8_1.cfg b/board/keymile/km_arm/kwbimage_256M8_1.cfg
new file mode 100644
index 0000000..3e1237b
--- /dev/null
+++ b/board/keymile/km_arm/kwbimage_256M8_1.cfg
@@ -0,0 +1,296 @@
+#
+# (C) Copyright 2012
+# Stefan Bigler, Keymile AG, stefan.bigler@keymile.com
+# Norbert Mayer, Keymile AG, norbert.mayer@keymile.com
+# Deepak Patel, XENTECH Limited, deepak.patel@xentech.co.uk
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+# This configuration applies to COGE5 design (ARM-part)
+# Two 8-Bit devices are connected on the 16-Bit bus on the same
+# chip-select. The supported devices are
+#   MT47H256M8EB-3IT:C
+#   MT47H256M8EB-25EIT:C
+
+# Boot Media configurations
+BOOT_FROM	spi	# Boot from SPI flash
+
+DATA 0xFFD10000 0x01112222	# MPP Control 0 Register
+# bit 3-0:   2, MPPSel0  SPI_CSn  (1=NF_IO[2])
+# bit 7-4:   2, MPPSel1  SPI_MOSI (1=NF_IO[3])
+# bit 12-8:  2, MPPSel2  SPI_SCK  (1=NF_IO[4])
+# bit 15-12: 2, MPPSel3  SPI_MISO (1=NF_IO[5])
+# bit 19-16: 1, MPPSel4  NF_IO[6]
+# bit 23-20: 1, MPPSel5  NF_IO[7]
+# bit 27-24: 1, MPPSel6  SYSRST_O
+# bit 31-28: 0, MPPSel7  GPO[7]
+
+DATA 0xFFD10004 0x03303300	# MPP Control 1 Register
+# bit 3-0:   0, MPPSel8	 GPIO[8] CPU_SDA bitbanged
+# bit 7-4:   0, MPPSel9  GPIO[9] CPU_SCL bitbanged
+# bit 12-8:  3, MPPSel10 UA0_TXD
+# bit 15-12: 3, MPPSel11 UA0_RXD
+# bit 19-16: 0, MPPSel12 not connected
+# bit 23-20: 3, MPPSel13 GPIO[14]
+# bit 27-24: 3, MPPSel14 GPIO[15]
+# bit 31-28: 0, MPPSel15 GPIO[16] BOOT_FL_SEL (SPI-MUX Signal)
+
+DATA 0xFFD10008 0x00001100	# MPP Control 2 Register
+# bit 3-0:   0, MPPSel16 GPIO[16]
+# bit 7-4:   0, MPPSel17 not connected
+# bit 11-8:  1, MPPSel18 NF_IO[0]
+# bit 15-12: 1, MPPSel19 NF_IO[1]
+# bit 19-16: 0, MPPSel20 GPIO[20]
+# bit 23-20: 0, MPPSel21 GPIO[21]
+# bit 27-24: 0, MPPSel22 GPIO[22]
+# bit 31-28: 0, MPPSel23 GPIO[23]
+
+# MPP Control 3-6 Register untouched (MPP24-49)
+
+DATA 0xFFD100E0 0x1B1B1B1B	# IO Configuration 0 Register
+# bit 2-0:   3, Reserved
+# bit 5-3:   3, Reserved
+# bit 6:     0, Reserved
+# bit 7:     0, RGMII-pads voltage = 3.3V
+# bit 10-8:  3, Reserved
+# bit 13-11: 3, Reserved
+# bit 14:    0, Reserved
+# bit 15:    0, MPP RGMII-pads voltage = 3.3V
+# bit 31-16  0x1B1B, Reserved
+
+DATA 0xFFD20134 0x66666666	# L2 RAM Timing 0 Register
+# bit 0-1:   2, Tag RAM RTC RAM0
+# bit 3-2:   1, Tag RAM WTC RAM0
+# bit 7-4:   6, Reserved
+# bit 9-8:   2, Valid RAM RTC RAM
+# bit 11-10: 1, Valid RAM WTC RAM
+# bit 13-12: 2, Dirty RAM RTC RAM
+# bit 15-14: 1, Dirty RAM WTC RAM
+# bit 17-16: 2, Data RAM RTC RAM0
+# bit 19-18: 1, Data RAM WTC RAM0
+# bit 21-20: 2, Data RAM RTC RAM1
+# bit 23-22: 1, Data RAM WTC RAM1
+# bit 25-24: 2, Data RAM RTC RAM2
+# bit 27-26: 1, Data RAM WTC RAM2
+# bit 29-28: 2, Data RAM RTC RAM3
+# bit 31-30: 1, Data RAM WTC RAM4
+
+DATA 0xFFD20138 0x66666666	# L2 RAM Timing 1 Register
+# bit 15-0:  ?, Reserved
+# bit 17-16: 2, ECC RAM RTC RAM0
+# bit 19-18: 1, ECC RAM WTC RAM0
+# bit 31-20: ?,Reserved
+
+DATA 0xFFD20154 0x00000200	# CPU RAM Management Control3 Register
+# bit 23-0:  0x000200, Addr Config tuning
+# bit 31-24: 0,        Reserved
+
+# ??? Missing register # CPU RAM Management Control2 Register
+
+DATA 0xFFD2014C 0x00001C00	# CPU RAM Management Control1 Register
+# bit 15-0:  0x1C00, Opmux Tuning
+# bit 31-16: 0,      Pc Dp Tuning
+
+DATA 0xFFD20148 0x00000001	# CPU RAM Management Control0 Register
+# bit 1-0:   1, addr clk tune
+# bit 3-2:   0, reserved
+# bit 5-4:   0, dtcmp clk tune
+# bit 7-6:   0, reserved
+# bit 9-8:   0, macdrv clk tune
+# bit 11-10: 0, opmuxgm2 clk tune
+# bit 15-14: 0, rf clk tune
+# bit 17-16: 0, rfbypass clk tune
+# bit 19-18: 0, pc dp clk tune
+# bit 23-20: 0, icache clk tune
+# bit 27:24: 0, dcache clk tune
+# bit 31:28: 0, regfile tunin
+
+# SDRAM initalization
+DATA 0xFFD01400 0x430004E0	# SDRAM Configuration Register
+# bit 13-0:  0x4E0, DDR2 clks refresh rate
+# bit 14:    0, reserved
+# bit 15:    0, reserved
+# bit 16:    0, CPU to Dram Write buffer policy
+# bit 17:    0, Enable Registered DIMM or Equivalent Sampling Logic
+# bit 19-18: 0, reserved
+# bit 23-20: 0, reserved
+# bit 24:    1, enable exit self refresh mode on DDR access
+# bit 25:    1, required
+# bit 29-26: 0, reserved
+# bit 31-30: 1, reserved
+
+DATA 0xFFD01404 0x36543000	# DDR Controller Control Low
+# bit 3-0:   0, reserved
+# bit 4:     0, 2T mode =addr/cmd in same cycle
+# bit 5:     0, clk is driven during self refresh, we don't care for APX
+# bit 6:     0, use recommended falling edge of clk for addr/cmd
+# bit 7-11:  0, reserved
+# bit 12-13: 1, reserved, required 1
+# bit 14:    0, input buffer always powered up
+# bit 17-15: 0, reserved
+# bit 18:    1, cpu lock transaction enabled
+# bit 19:    0, reserved
+# bit 23-20: 5, recommended value for CL=4 and STARTBURST_DEL disabled bit31=0
+# bit 27-24: 6, CL+1, STARTBURST sample stages, freq 200-399MHz, unbuffer DIMM
+# bit 30-28: 3, required
+# bit 31:    0, no additional STARTBURST delay
+
+DATA 0xFFD01408 0x2202444E	# DDR Timing (Low) (active cycles value +1)
+# bit 3-0:   0xe, TRAS = 45ns -> 15 clk cycles
+# bit 7-4:   0x4, TRCD = 15ns -> 5 clk cycles
+# bit 11-8:  0x4, TRP = 15ns -> 5 clk cycles
+# bit 15-12: 0x4, TWR = 15ns -> 5 clk cycles
+# bit 19-16: 0x2, TWTR = 7,5ns -> 3 clk cycles
+# bit 20:      0, extended TRAS msb
+# bit 23-21:   0, reserved
+# bit 27-24: 0x2, TRRD = 7,5ns -> 3 clk cycles
+# bit 31-28: 0x2, TRTP = 7,5ns -> 3 clk cycles
+
+DATA 0xFFD0140C 0x0000003E	#  DDR Timing (High)
+# bit 6-0:   0x3E, TRFC = 195ns -> 63 clk cycles
+# bit 8-7:      0, TR2R
+# bit 10-9:     0, TR2W
+# bit 12-11:    0, TW2W
+# bit 31-13:    0, reserved
+
+DATA 0xFFD01410 0x00000000	#  DDR Address Control
+# bit 1-0:    0, Cs0width=x8 (2 devices)
+# bit 3-2:    0, Cs0size=2Gb
+# bit 5-4:    0, Cs1width=nonexistent
+# bit 7-6:    0, Cs1size =nonexistent
+# bit 9-8:    0, Cs2width=nonexistent
+# bit 11-10:  0, Cs2size =nonexistent
+# bit 13-12:  0, Cs3width=nonexistent
+# bit 15-14:  0, Cs3size =nonexistent
+# bit 16:     0, Cs0AddrSel
+# bit 17:     0, Cs1AddrSel
+# bit 18:     0, Cs2AddrSel
+# bit 19:     0, Cs3AddrSel
+# bit 31-20:  0, required
+
+DATA 0xFFD01414 0x00000000	#  DDR Open Pages Control
+# bit 0:      0,  OpenPage enabled
+# bit 31-1:   0, required
+
+DATA 0xFFD01418 0x00000000	#  DDR Operation
+# bit 3-0:    0, DDR cmd
+# bit 31-4:   0, required
+
+DATA 0xFFD0141C 0x00000652	#  DDR Mode
+# bit 2-0:    2, Burst Length = 4
+# bit 3:      0, Burst Type
+# bit 6-4:    5, CAS Latency = 5
+# bit 7:      0, Test mode
+# bit 8:      0, DLL Reset
+# bit 11-9:   3, Write recovery for auto-precharge must be 3
+# bit 12:     0, Active power down exit time, fast exit
+# bit 14-13:  0, reserved
+# bit 31-15:  0, reserved
+
+DATA 0xFFD01420 0x00000006	#  DDR Extended Mode
+# bit 0:      0, DDR DLL enabled
+# bit 1:      1, DDR drive strenght reduced
+# bit 2:      1, DDR ODT control lsb, 75ohm termination [RTT0]
+# bit 5-3:    0, required
+# bit 6:      0, DDR ODT control msb, 75ohm termination [RTT1]
+# bit 9-7:    0, required
+# bit 10:     0, differential DQS enabled
+# bit 11:     0, required
+# bit 12:     0, DDR output buffer enabled
+# bit 31-13:  0 required
+
+DATA 0xFFD01424 0x0000F17F	#  DDR Controller Control High
+# bit 2-0:    7, required
+# bit 3:      1, MBUS Burst Chop disabled
+# bit 6-4:    7, required
+# bit 7:      0, reserved
+# bit 8:      1, add sample stage required for > 266Mhz
+# bit 9:      0, no half clock cycle addition to dataout
+# bit 10:     0, 1/4 clock cycle skew enabled for addr/ctl signals
+# bit 11:     0, 1/4 clock cycle skew disabled for write mesh
+# bit 15-12:0xf, required
+# bit 31-16:  0, required
+
+DATA 0xFFD01428 0x00084520	# DDR2 SDRAM Timing Low
+# bit 3-0:    0, required
+# bit 7-4:    2, M_ODT assertion 2 cycles after read start command
+# bit 11-8:   5, M_ODT de-assertion 5 cycles after read start command
+#                (ODT turn off delay 2,5 clk cycles)
+# bit 15-12:  4, internal ODT time based on bit 7-4
+#                with the considered SDRAM internal delay
+# bit 19-16:  8, internal ODT de-assertion based on bit 11-8
+#                with the considered SDRAM internal delay
+# bit 31-20:  0, required
+
+DATA 0xFFD0147c 0x00008452	# DDR2 SDRAM Timing High
+# bit 3-0:    2, M_ODT assertion same as bit 11-8
+# bit 7-4:    5, M_ODT de-assertion same as bit 15-12
+# bit 11-8:   4, internal ODT assertion 2 cycles after write start command
+#                with the considered SDRAM internal delay
+# bit 15-12:  8, internal ODT de-assertion 5 cycles after write start command
+#                with the considered SDRAM internal delay
+
+DATA 0xFFD01500 0x00000000	# CS[0]n Base address to 0x0
+# bit 23-0:   0, reserved
+# bit 31-24:  0, CPU CS Window0 Base Address, addr bits [31:24]
+
+DATA 0xFFD01504 0x1FFFFFF1	# CS[0]n Size
+# bit 0:      1, Window enabled
+# bit 1:      0, Write Protect disabled
+# bit 3-2:    0, CS0 hit selected
+# bit 23-4:ones, required
+# bit 31-24:0x1F, Size (i.e. 512MB)
+
+DATA 0xFFD0150C 0x00000000	# CS[1]n Size, window disabled
+DATA 0xFFD01514 0x00000000	# CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000	# CS[3]n Size, window disabled
+
+DATA 0xFFD01494 0x00010000	#  DDR ODT Control (Low)
+# bit 3-0:     0, ODT0Rd, MODT[0] not asserted during read from DRAM CS0
+# bit 7-4:     0, ODT0Rd, MODT[1] not asserted
+# bit 11-8:    0, required
+# big 15-11:   0, required
+# bit 19-16:   1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
+# bit 23-20:   0, ODT0Wr, MODT[1] not asserted
+# bit 27-24:   0, required
+# bit 31-28:   0, required
+
+DATA 0xFFD01498 0x00000004	#  DDR ODT Control (High)
+# bit 1-0:     0, ODT0 controlled by ODT Control (low) register above
+# bit 3-2:     1, ODT1 never active
+# bit 31-4:    0, required
+
+DATA 0xFFD0149C 0x0000E801	# CPU ODT Control
+# bit 3-0:     1, ODT0Rd, Internal ODT asserted during read from DRAM bank0
+# bit 7-4:     0, ODT0Wr, Internal ODT not asserted during write to DRAM bank0
+# bit 9-8:     0, ODTEn, controlled by ODT0Rd and ODT0Wr
+# bit 11-10:   2, DQ_ODTSel. ODT select turned on, 75 ohm
+# bit 13-12:   2, STARTBURST ODT buffer selected, 75 ohm
+# bit 14:      1, STARTBURST ODT enabled
+# bit 15:      1, Use ODT Block
+
+DATA 0xFFD01480 0x00000001	# DDR Initialization Control
+# bit 0:       1, enable DDR init upon this register write
+# bit 31-1:    0, reserved
+
+# End of Header extension
+DATA 0x0 0x0
diff --git a/boards.cfg b/boards.cfg
index 64b5dbc..808f85b 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -144,6 +144,7 @@
 km_kirkwood_pci              arm         arm926ejs   km_arm              keymile        kirkwood    km_kirkwood:KM_KIRKWOOD_PCI,KM_RECONFIG_XLX
 kmnusa                       arm         arm926ejs   km_arm              keymile        kirkwood    km_kirkwood:KM_NUSA
 mgcoge3un                    arm         arm926ejs   km_arm              keymile        kirkwood
+kmcoge5un                    arm         arm926ejs   km_arm              keymile        kirkwood    km_kirkwood:KM_COGE5UN
 portl2                       arm         arm926ejs   km_arm              keymile        kirkwood
 inetspace_v2                 arm         arm926ejs   netspace_v2         LaCie          kirkwood	lacie_kw:INETSPACE_V2
 net2big_v2                   arm         arm926ejs   net2big_v2          LaCie          kirkwood	lacie_kw:NET2BIG_V2
diff --git a/include/configs/km_kirkwood.h b/include/configs/km_kirkwood.h
index 34dd0a6..d839a02 100644
--- a/include/configs/km_kirkwood.h
+++ b/include/configs/km_kirkwood.h
@@ -39,15 +39,18 @@
 
 #if defined(CONFIG_KM_KIRKWOOD)
 #define CONFIG_IDENT_STRING		"\nKeymile Kirkwood"
+#define CONFIG_HOSTNAME			km_kirkwood
 #undef  CONFIG_KIRKWOOD_PCIE_INIT
 #define KM_IVM_BUS			"pca9544a:70:9"	/* I2C2 (Mux-Port 1)*/
 #elif defined(CONFIG_KM_KIRKWOOD_PCI)
 #define CONFIG_IDENT_STRING		"\nKeymile Kirkwood PCI"
+#define CONFIG_HOSTNAME			km_kirkwood_pci
 #define KM_IVM_BUS			"pca9544a:70:9"	/* I2C2 (Mux-Port 1)*/
 /* KM_NUSA */
 #elif defined(CONFIG_KM_NUSA)
 #define KM_IVM_BUS			"pca9547:70:9"	/* I2C2 (Mux-Port 1)*/
 #define CONFIG_IDENT_STRING		"\nKeymile NUSA"
+#define CONFIG_HOSTNAME			kmnusa
 #undef CONFIG_SYS_KWD_CONFIG
 #define CONFIG_SYS_KWD_CONFIG \
 		$(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage_128M16_1.cfg
@@ -55,6 +58,17 @@
 #define CONFIG_KM_FPGA_CONFIG
 #define CONFIG_KM_PIGGY4_88E6352
 
+#elif defined(CONFIG_KM_COGE5UN)
+#define CONFIG_IDENT_STRING		"\nKeymile COGE5UN"
+#define KM_IVM_BUS			"pca9547:70:9"	/* I2C2 (Mux-Port 1)*/
+#undef	CONFIG_SYS_KWD_CONFIG
+#define CONFIG_SYS_KWD_CONFIG \
+		$(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage_256M8_1.cfg
+#define CONFIG_KM_ENV_IS_IN_SPI_NOR
+#define CONFIG_PIGGY_MAC_ADRESS_OFFSET	3
+#define CONFIG_HOSTNAME			kmcoge5un
+#define CONFIG_KM_DISABLE_PCIE
+#define CONFIG_KM_PIGGY4_88E6352
 #else
 #error ("Board unsupported")
 #endif
@@ -62,8 +76,6 @@
 /* include common defines/options for all arm based Keymile boards */
 #include "km/km_arm.h"
 
-#define CONFIG_HOSTNAME			km_kirkwood
-
 #ifndef CONFIG_KM_ENV_IS_IN_SPI_NOR
 #define KM_ENV_BUS	"pca9544a:70:d"	/* I2C2 (Mux-Port 5)*/
 #endif