imx: mx6qsabrelite: Update the SabreLite README
The information in the SabreLite README is inaccurate and sparse. The
upstream U-Boot can boot the SabreLite from SPI-NOR. Additionally, the
freely available imx_loader tool can be easily used to boot a board with a
corrupted SPI, the official Freescale/NXP manufacturing tools are not
required.
Reformat the document, adding a description of how to boot from SPI-NOR
and adding a brief description of how to recover the board should the
SPI-NOR be corrupted using imx_loader.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
diff --git a/board/boundary/nitrogen6x/README.mx6qsabrelite b/board/boundary/nitrogen6x/README.mx6qsabrelite
index 12a9c85..6283c95 100644
--- a/board/boundary/nitrogen6x/README.mx6qsabrelite
+++ b/board/boundary/nitrogen6x/README.mx6qsabrelite
@@ -1,72 +1,119 @@
U-Boot for the Freescale i.MX6q SabreLite board
+===============================================
This file contains information for the port of U-Boot to the Freescale
i.MX6q SabreLite board.
-1. Boot source, boot from SD card
----------------------------------
-The recent mainline U-Boot for the Freescale i.MX6q SabreLite board supports
-boot from SD card only. However, by default, the SabreLite
-boards boot from the SPI NOR flash. These boards need to be reflashed with
-a small SD card loader to support boot from SD card. This small SD card loader
-will be flashed into the SPI NOR. The board will still boot from SPI NOR, but
-the loader will in turn request the BootROM to load the U-Boot from SD card.
+1. Build
+--------
+
+To build U-Boot for the SabreLite board:
+
+ make mx6qsabrelite_config
+ make
+
+
+2. Boot from SD card
+--------------------
+
+The SabreLite boards boot from the SPI NOR flash. These boards need their SPI
+to be reflashed with a small SD card loader to support boot from SD card. The
+board will still boot from SPI NOR, but the loader will in turn request the
+BootROM to load the U-Boot from SD card.
The SD card loader is available from
https://wiki.linaro.org/Boards/MX6QSabreLite
-under a open-source 3-clause BSD license.
+This is provided under a open-source 3-clause BSD license.
-To update the SPI-NOR on the SabreLite board without the Freescale
-manufacturing tool use the following procedure:
+To following procedure can be used to update the SPI-NOR on the SabreLite
+board:
1. Write this SD card loader onto a large SD card using:
- sudo dd if=iMX6DQ_SPI_to_uSDHC3.bin of=/dev/sXx
+ sudo dd if=iMX6DQ_SPI_to_uSDHC3.bin of=/dev/sXx
-Note: Replace sXx with the device representing the SD card in your system.
+ Note: Replace sXx with the device representing the SD card in your system.
-Note: This writes SD card loader at address 0
+ Note: This writes SD card loader at address 0
2. Put this SD card into the slot for the large SD card (SD3 on the bottom of
-the board). Make sure SW1 switch is at position "00", so that it can boot
-from the fuses.
+ the board). Make sure SW1 switch is at position "00", so that it can boot
+ from the fuses.
3. Power-up the SabreLite, press 'space' to enter command mode in the U-Boot
-(the default one the board is shipped with, starting from the SPI NOR) and
-enter the following commands:
+ (the default one the board is shipped with, starting from the SPI NOR) and
+ enter the following commands:
+
+ MX6Q SABRELITE U-Boot > mmc dev 0
+ MX6Q SABRELITE U-Boot > mmc read 0x10800000 0 200
+ MX6Q SABRELITE U-Boot > sf probe
+ MX6Q SABRELITE U-Boot > sf erase 0 0x40000
+ MX6Q SABRELITE U-Boot > sf write 0x10800000 0 0x40000
- MX6Q SABRELITE U-Boot > mmc dev 0
- MX6Q SABRELITE U-Boot > mmc read 0x10800000 0 200
- MX6Q SABRELITE U-Boot > sf probe
- MX6Q SABRELITE U-Boot > sf erase 0 0x40000
- MX6Q SABRELITE U-Boot > sf write 0x10800000 0 0x40000
+4. Write the u-boot.imx produced during the U-Boot build to the SD card:
-4. done.
+ sudo dd if=u-boot.imx of=/dev/sXx bs=512 seek=2 && sudo sync
-In case you somehow do not succeed with this procedure you will have to use
-the Freescale manufacturing tool in order to reflash the SPI-NOR.
+ Note: Replace sXx with the device representing the SD card in your system.
+
+5. Re-insert the SD card back in the slot for the large SD card and power-cycle
+ the board.
Note: The board now boots from full size SD3 on the bottom of the board. NOT
the micro SD4/BOOT slot on the top of the board. I.e. you have to use
full size SD cards.
-This information is taken from
+This information originally taken from:
-https://wiki.linaro.org/Boards/MX6QSabreLite
+ https://wiki.linaro.org/Boards/MX6QSabreLite
-2. Build
---------
-To build U-Boot for the SabreLite board:
+3. Boot from SPI NOR
+--------------------
- make mx6qsabrelite_config
- make
+The SabreLite board can also boot U-Boot directly from the SPI NOR flash:
+
+1. Power-up the SabreLite, press 'space' to enter command mode in the U-Boot
+ and enter the following commands:
+
+ => mmc dev 0
+ => mmc read 0x10800000 0x400 0x80000
+ => sf probe 0
+ => sf erase 0 0xc0000
+ => sf write 0x10800000 0x400 0x80000
+
+Note: This procedure assumes you have booted using the desired U-Boot from an
+ SD card as prepared in the previous section. Alternative mechanisms, such
+ as using tftpboot to copy an alternative U-Boot image into memory can
+ also be used.
+
+
+4. Recovering SPI-NOR
+---------------------
+
+In case you somehow do not succeed with this procedure you can upload U-Boot
+via USB:
-To copy the resulting u-boot.imx to the SD card:
+1. Download and install the imx_loader following the instructions provided:
- sudo dd if=u-boot.imx of=/dev/sXx bs=512 seek=2&&sudo sync
+ https://github.com/boundarydevices/imx_usb_loader
+
+2. Connect the board to USB via the USB OTG port.
+
+3. Make sure SW1 switch is at position "01", so that it can boot from USB OTG.
+
+4. Power-up the SabreLite and run the imx_loader to upload the U-Boot image:
+
+ sudo imx_usb u-boot.imx
+
+Note: This will upload and run the U-Boot image in memory, the SPI will not be
+ reprogrammed and this procedure will need to be repeated if the board is
+ reset.
+
+5. Use one of previous descriptions to re-flash the SPI-NOR as required.
+
+6. Ensure SW1 is returned to "00" to boot from the fuses once done.
-Note: Replace sXx with the device representing the SD card in your system.