Merge with /home/wd/git/u-boot/custodian/u-boot-mpc86xx
diff --git a/CHANGELOG b/CHANGELOG
index 284ba76..780a2c4 100644
--- a/CHANGELOG
+++ b/CHANGELOG
@@ -1,3 +1,689 @@
+commit 5f6c732affea9647762d27a4617a2ae64c52dceb
+Author: Wolfgang Denk <wd@denx.de>
+Date: Wed Apr 18 16:17:46 2007 +0200
+
+ Update CHANGELOG
+
+commit ad4eb555671d97f96dc56eab55103b1f86874b01
+Author: Wolfgang Denk <wd@denx.de>
+Date: Wed Apr 18 14:30:39 2007 +0200
+
+ MCC200 board: remove warning which is obsolete after PSoC firmware changes
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit 3747a3f010b2b1442dec3e871c69788b6017aaae
+Author: Domen Puncer <domen.puncer@telargo.com>
+Date: Wed Apr 18 12:11:05 2007 +0200
+
+ [PATCH] icecube/lite5200b: document wakeup from low-power support
+
+ Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
+
+commit e673226ff9d6aa91b47ceac74b8c13770b06bb37
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Apr 18 12:07:47 2007 +0200
+
+ ppc4xx: Update Acadia to not setup PLL when booting via bootstrap EEPROM
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 90e6f41cf09fc98f6ccb510e183d53ab8546cf2f
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Apr 18 12:05:59 2007 +0200
+
+ ppc4xx: Add output for bootrom location to 405EZ ports
+
+ Now 405EZ ports also show upon bootup from which boot device
+ they are configured to boot:
+
+ U-Boot 1.2.0-gd3832e8f-dirty (Apr 18 2007 - 07:47:05)
+
+ CPU: AMCC PowerPC 405EZ Rev. A at 199.999 MHz (PLB=133, OPB=66, EBC=66 MHz)
+ Bootstrap Option E - Boot ROM Location EBC (32 bits)
+ 16 kB I-Cache 16 kB D-Cache
+ Board: Acadia - AMCC PPC405EZ Evaluation Board
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit d3832e8fe1b214ec62424eac36cfda9fc56d21b3
+Author: Domen Puncer <domen.puncer@telargo.com>
+Date: Mon Apr 16 14:00:13 2007 +0200
+
+ [PATCH] icecube/lite5200b: wakeup from low-power support
+
+ U-Boot part of Lite5200b low power mode support.
+ Puts SDRAM out of self-refresh and transfers control to
+ address saved at physical 0x0.
+
+ Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
+ Acked-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit 8048cdd56f04a756eeea4951f402bf5cc33785db
+Author: Wolfgang Denk <wd@denx.de>
+Date: Sat Apr 14 21:16:54 2007 +0200
+
+ Update CHANGELOG
+
+commit 8e6875183cdca91c134408d119d4abcd48ef6856
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Sun Dec 17 18:56:46 2006 +0100
+
+ AVR32: Enable MMC support
+
+ Set up the portmux for the MMC interface and enable the MMC driver
+ along with support for DOS partitions, ext2 and FAT filesystems.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit fc26c97bb6df41b4a95662c34054fe912387bf38
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Fri Jan 20 10:03:53 2006 +0100
+
+ Atmel MCI driver
+
+ Driver for the Atmel MCI controller (MMC interface) for AT32AP CPUs.
+
+ The AT91 ARM-based CPUs use basically the same hardware, so it should
+ be possible to share this driver, but no effort has been made so far.
+
+ Hardware documentation can be found in the AT32AP7000 data sheet,
+ which can be downloaded from
+
+ http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 05fdab1ef6a10d049a50021a86f1226f444d9b9f
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Sun Dec 17 18:55:37 2006 +0100
+
+ AVR32: Add clk and gpio infrastructure for mmci
+
+ Implement functions for configuring the mmci pins, as well as
+ functions for getting the clock rate of the mmci controller.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 7fac3f69e9f05c5e5326681976c35d129324c4de
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Sun Dec 17 18:53:56 2006 +0100
+
+ Enable partition support with MMC
+
+ Include implementations of init_part() and get_partition_info() when
+ CONFIG_MMC is set.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 9a24f477a1ed5bb0f74377c985d754ebbfa44872
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Sun Dec 17 17:14:30 2006 +0100
+
+ AVR32: Enable networking
+
+ Implement MACB initialization for AVR32 and ATSTK1000, and turn
+ everything on, including the MACB driver.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 5c1fe1ffffd1750a7e47e5a2e2cd600c00e4f009
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Fri Jan 20 10:03:34 2006 +0100
+
+ Atmel MACB ethernet driver
+
+ Driver for the Atmel MACB on-chip ethernet controller.
+
+ This driver has been tested on the ATSTK1000 board with a AT32AP7000
+ CPU. It should probably work on AT91SAM926x as well with some minor
+ modifications.
+
+ Hardware documentation can be found in the AT32AP7000 data sheet,
+ which can be downloaded from
+
+ http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit b4ec9c2d43d894729bb633bfdbdfa95a962c1556
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Sun Dec 17 16:56:14 2006 +0100
+
+ AVR32: Add clk and gpio infrastructure for macb0 and macb1
+
+ Implement functions for configuring the macb0 and macb1 pins, as
+ well as functions for getting the clock rate of the various
+ busses the macb ethernet controllers are connected to.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit d5acb95b16a0a74c643524342c3437e765426d05
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Sun Dec 17 15:39:15 2006 +0100
+
+ AVR32: Implement simple DMA memory allocator
+
+ Implement dma_alloc_coherent() which returns cache-aligned
+ uncacheable memory.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 91975b0fea773c9e681fea8cf3349669f27685ee
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Sun Dec 17 15:46:02 2006 +0100
+
+ Import <linux/mii.h> from the Linux kernel
+
+ Instead of creating yet another set of MII register definitions
+ in the macb driver, here's a complete set of definitions for everyone
+ to use.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 1b804b229556a4d862da93c0ec94e79419364b2c
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Wed Mar 21 19:47:36 2007 +0100
+
+ AVR32: Include more commands for ATSTK1000
+
+ Include the imi, imls and jffs commands sets by default on ATSTK1000.
+ Also define CONFIG_BOOTARGS to something more useful, define
+ CONFIG_BOOTCOMMAND and enable autoboot by default.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 9c0deb5ae3ea0189f2e08ac29ef1316f1fb8548d
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Wed Mar 21 19:44:48 2007 +0100
+
+ AVR32: Provide a definition of struct stat
+
+ Copy the definition of struct stat from the Linux kernel.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 12f099c08167a7a51aeee623bc16dafd0841271c
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Sun Dec 17 14:46:06 2006 +0100
+
+ AVR32: Use initdram() instead of board_init_memories()
+
+ Conform to the "standard" interface and use initdram() instead of
+ board_init_memories() on AVR32. This enables us to get rid of the
+ sdram_size member of the global_data struct as well.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 1f4f2121c2685182eb87fa9a9b799d1917387a1c
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Mon Nov 20 15:53:10 2006 +0100
+
+ AVR32: Relocate u-boot to SDRAM
+
+ Relocate the u-boot image into SDRAM like everyone else does. This
+ means that we can handle much larger .data and .bss than we used to.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit df548d3c3e2bbc40258713167859ffc2ce99a900
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Sun Nov 19 18:06:53 2006 +0100
+
+ AVR32: Resource management rewrite
+
+ Rewrite the resource management code (i.e. I/O memory, clock gating,
+ gpio) so it doesn't depend on any global state. This is necessary
+ because this code is heavily used before relocation to RAM, so we
+ can't write to any global variables.
+
+ As an added bonus, this makes u-boot's memory footprint a bit smaller,
+ although some functionality has been left out; all clocks are enabled
+ all the time, and there's no checking for gpio line conflicts.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 03d1e1365796cd15d1726e8a51fd8b5be50b2fe9
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Sat Nov 18 18:01:13 2006 +0100
+
+ AVR32: Clean up memory-map.h for at32ap7000
+
+ Convert spaces to tabs (must have missed this one last time around),
+ sort the entries by address and group them together by bus
+ connectivity.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 28c699ef69f4b6cdf252e4747b7b590028a88981
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Sat Nov 18 17:32:31 2006 +0100
+
+ AVR32: Build position-independent u-boot
+
+ Add -fPIC -mno-init-got to the avr32-specific CFLAGS to make u-boot
+ position independent. This will make relocation a lot easier.
+
+ -mno-init-got means that gcc shouldn't emit code to load the GOT
+ address into r6 in every function prologue. We do it once and for
+ all in the early startup assembly code, so enabling this option
+ makes u-boot a bit faster and smaller.
+
+ The assembly parts have always been position-independent, so no code
+ changes should be necessary.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 5374b36de91d006d1df9536259fa9f66b01aa3aa
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Sat Nov 18 17:24:31 2006 +0100
+
+ AVR32: Use avr32-linux- cross-compilation prefix by default
+
+ It doesn't really matter which toolchain you use to compile u-boot,
+ but the avr32-linux one is probably what most people have installed.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit c841beeddebece0039e724fb27f4d1a39ee1c6b6
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date: Sat Nov 18 17:15:30 2006 +0100
+
+ AVR32: Split start_u_boot into board_init_f and board_init_r
+
+ Split the avr32 initialization code into a function to run before
+ relocation, board_init_f and a function to run after relocation,
+ board_init_r. For now, board_init_f simply calls board_init_r
+ at the end.
+
+ Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 37403005cfe6bb13964d450f6a48a0b0f2f7017e
+Author: Heiko Schocher <hs@pollux.denx.de>
+Date: Sat Apr 14 05:26:48 2007 +0200
+
+ [Fix] Set the LED status register on the UC101 for the LXT971 PHY.
+ clear the Display after reset.
+
+ Signed-off-by: Heiko Schocher <hs@denx.de>
+
+commit 7882751c78b7ecabfd49b0eff8de27661c71f16c
+Author: Denis Peter <d.peter@mpl.ch>
+Date: Fri Apr 13 09:13:33 2007 +0200
+
+ [PATCH] Fix bugs in cmd_ide.c and cmd_scsi.c
+
+ Fix bug introduced by "Fix get_partition_info() parameter error in all
+ other calls" from 2005-03-04 in cmd_ide.c and cmd_scsi.c, which prevented
+ to use diskboot or scsiboot form another device than 0.
+
+ Signed-off-by: Denis Peter <d.peter@mpl.ch>
+
+commit 0b94504d22e70f537c17a0d38c87edb6e370977d
+Author: Greg Lopp <lopp@pobox.com>
+Date: Fri Apr 13 08:02:24 2007 +0200
+
+ [PATCH] Fix use of "void *" for block dev read/write buffer pointers
+
+ Signed-of-by: Greg Lopp <lopp@pobox.com>
+ Acked-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit 2ad3aba01d37b72e7c957b07e102fccd64fe6d13
+Author: Jeffrey Mann <mannj@embeddedplanet.com>
+Date: Thu Apr 12 14:15:59 2007 +0200
+
+ ppc4xx: Fix i2c divisor calcularion for PPC4xx
+
+ This patch fixes changes the i2c_init(...) function to use the function
+ get_OPB_freq() rather than calculating the OPB speed by
+ sysInfo.freqPLB/sysInfo.pllOpbDiv. The get_OPB_freq() function is
+ specific per processor. The prior method was not and so was calculating
+ the wrong speed for some PPC4xx processors.
+
+ Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 6c9ba919375db977aaad9146bf320c7afd07ae7a
+Author: Wolfgang Denk <wd@denx.de>
+Date: Wed Apr 11 17:25:01 2007 +0200
+
+ Update CHANGELOG
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit 51056dd9863e6a1bc363afbbe1775c58cd967418
+Author: Wolfgang Denk <wd@denx.de>
+Date: Wed Apr 11 17:22:55 2007 +0200
+
+ Update for SC3 board
+
+ * Make IDE timeout configurable through ide_reset_timeout variable.
+ * Use Newline as "password" string
+ * Use just a single partition in NAND flash
+
+commit c0707ce65677650b5ceab0500ee50ae5168afef2
+Author: Aubrey Li <aubrey.adi@gmail.com>
+Date: Thu Apr 5 18:34:06 2007 +0800
+
+ [Blackfin][PATCH] Kill off a bunch of common local prototypes
+
+commit 7b7e30aa64bb6657a1bfd32fdbdbfeb561e6a48d
+Author: Aubrey Li <aubrey.adi@gmail.com>
+Date: Thu Apr 5 18:33:04 2007 +0800
+
+ [Blackfin][PATCH] Fix dynamic CPLB generation issue
+
+commit 0445e3a264251d75b1be45ef713c70726a2952f0
+Author: Aubrey Li <aubrey.adi@gmail.com>
+Date: Thu Apr 5 18:31:47 2007 +0800
+
+ [Blackfin][PATCH] minior cleanup
+
+commit 155fd766573981090e638b493d5857562151862e
+Author: Aubrey Li <aubrey.adi@gmail.com>
+Date: Thu Apr 5 18:31:18 2007 +0800
+
+ [Blackfin][PATCH] Fix copyright and update license
+
+commit 9fd437bbd75d282f899e1da50be20a2bf38450bc
+Author: Aubrey Li <aubrey.adi@gmail.com>
+Date: Thu Apr 5 18:30:25 2007 +0800
+
+ [Blackfin][PATCH] Add BF537 EMAC driver initialization
+
+commit 889256e8604e0c68db1d866d720894dffede9df6
+Author: Aubrey Li <aubrey.adi@gmail.com>
+Date: Thu Apr 5 18:29:55 2007 +0800
+
+ [Blackfin][PATCH] call real the system synchronize instruction
+
+commit e0df1c921b788289564e4c1ee7120a6a9cd3ab05
+Author: Aubrey Li <aubrey.adi@gmail.com>
+Date: Thu Apr 5 18:29:17 2007 +0800
+
+ [Blackfin][PATCH] remove asm/page.h as we do not actually use/want any of these definitions nor does any other arch include it
+
+commit dfeeab2cd680df047e68e723b246adf6f33bb556
+Author: Aubrey Li <aubrey.adi@gmail.com>
+Date: Thu Apr 5 18:28:34 2007 +0800
+
+ [Blackfin][PATCH]: fix flash unaligned copy issue
+
+commit 31c98a88228021b314c89ebb8104fb6473da4471
+Author: Wolfgang Denk <wd@denx.de>
+Date: Wed Apr 4 02:09:30 2007 +0200
+
+ Minor coding style cleanup.
+
+commit 94abd7c0583ebe01e799b25f451201deeaab550d
+Author: Wolfgang Denk <wd@denx.de>
+Date: Wed Apr 4 01:49:15 2007 +0200
+
+ Minor cleanup.
+
+commit a65c5768e5537530bd1780af3d3fddc3113a163c
+Author: Stefan Roese <sr@denx.de>
+Date: Mon Apr 2 10:09:30 2007 +0200
+
+ ppc4xx: Change SysACE address on Katmai
+
+ With this new base address of the Xilinx SystemACE controller
+ the Linux driver will be easier to adapt, since it can now be
+ mapped via the "normal" ioremap() call.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit aea03c4e8c3a21ce43d3faf48a6e6d474c8bdf73
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date: Sat Mar 31 14:30:53 2007 -0400
+
+ Fix some minor whitespace violations.
+
+commit 213bf8c822de8eecaf69860684469cdaba2e9e6a
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date: Sat Mar 31 12:23:51 2007 -0400
+
+ Add a flattened device tree (fdt) command (2 of 2)
+
+ Modifications to the existing code to support the new fdt command.
+
+commit 781e09ee6e3e3e392ab362c1f0ef1068adc76e3e
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date: Sat Mar 31 12:22:10 2007 -0400
+
+ Add a flattened device tree (fdt) command (1 of 2)
+
+ The fdt command uses David Gibson's libfdt library to manipulate as well
+ as print the flattened device tree. This patch is the new command,
+ the second part is the modifications to the existing code.
+
+commit 3af0d587d93e0be5f96e1b30fa41e662f8b0803e
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date: Sat Mar 31 12:13:43 2007 -0400
+
+ libfdt: Enhanced and published fdt_next_tag()
+
+ Enhanced the formerly private function _fdt_next_tag() to allow stepping
+ through the tree, used to produce a human-readable dump, and made
+ it part of the published interface.
+ Also added some comments.
+
+commit fa3a74cec73dfd06a5ae35a9a3368200273aaa71
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date: Sat Mar 31 12:05:39 2007 -0400
+
+ libfdt: Customizations for use by u-boot.
+
+ Changes to David Gibson's original source to fit into u-boot's
+ environment. No functionality changes.
+
+commit 35748177c64a4a83a00057e93bb33e40278a2a96
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date: Sat Mar 31 12:00:56 2007 -0400
+
+ libfdt: Import libfdt source (2 of 2)
+
+ This adds the applicable libfdt source files (unmodified) and a README
+ to explain where the source came from.
+
+commit 7cd5da0fe877e7171a4cdd44880bce783132871a
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date: Sat Mar 31 11:59:59 2007 -0400
+
+ libfdt: Import libfdt source (1 of 2)
+
+ This adds the applicable libfdt source files (unmodified) and a README
+ to explain where the source came from.
+
+commit da6ebc1bc082cbe3b6bbde079cafe09f7ebbad4b
+Author: Stefan Roese <sr@denx.de>
+Date: Sat Mar 31 13:16:23 2007 +0200
+
+ ppc4xx: Update Katmai bootstrap command
+
+ Now the DDR2 frequency is also 2*PLB frequency when 166MHz PLB
+ is selected.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit cabee756a6532986729477c3cc1ea16ef8517ad2
+Author: Stefan Roese <sr@denx.de>
+Date: Sat Mar 31 13:15:06 2007 +0200
+
+ ppc4xx: Update 44x_spd_ddr2 code (440SP/440SPe)
+
+ Additional RAM information is now printed upon powerup, like
+ DDR2 frequency and CAS latency.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 60723803431ac75cad085690789e433d5ab9174e
+Author: Stefan Roese <sr@denx.de>
+Date: Sat Mar 31 08:48:36 2007 +0200
+
+ ppc4xx: Change Yucca config file to support ECC
+
+ With the updated 44x DDR2 driver the Yucca board now supports
+ ECC generation and checking.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 490e5730c674b20d708b783a2c5ffd7208f83873
+Author: Stefan Roese <sr@denx.de>
+Date: Sat Mar 31 08:47:34 2007 +0200
+
+ ppc4xx: Fix "bootstrap" command for Katmai board
+
+ The board specific "bootstrap" command is now fixed and can
+ be used for the AMCC Katmai board to configure different
+ CPU/PLB/OPB frequencies.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 94f54703c3a776ec23e427ca2a16e0a79a5d50c1
+Author: Stefan Roese <sr@denx.de>
+Date: Sat Mar 31 08:46:08 2007 +0200
+
+ ppc4xx: Update 44x_spd_ddr2 code (440SP/440SPe)
+
+ Fix a bug in the auto calibration routine. This driver now runs
+ more reliable with the tested modules. It's also tested with
+ 167MHz PLB frequency (667MHz DDR2 frequency) on the Katmai.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 342cd097be1e7affe82f42ab3da220959a699e64
+Author: Michal Simek <monstr@monstr.eu>
+Date: Fri Mar 30 22:52:09 2007 +0200
+
+ [PATCH] Clean include dependence
+
+commit 6f934210fb293fde2cfb4251c6d96fdc58b6a906
+Author: Michal Simek <monstr@monstr.eu>
+Date: Fri Mar 30 22:42:45 2007 +0200
+
+ [CLEAN] Remove inefficient Suzaku code
+
+commit 430f1b0f9a670c2f13eaa52e66a10db96dd3647d
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Mar 28 15:03:16 2007 +0200
+
+ Merge some AMCC make targets to keep the top-level Makefile smaller
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 0c75c9d84307a9f1cbe1ff0c4d8937ee3a96475e
+Author: Stefan Roese <sr@denx.de>
+Date: Wed Mar 28 14:52:12 2007 +0200
+
+ i2c: Enable "old" i2c commands even when CONFIG_I2C_CMD_TREE is defined
+
+ The "old" i2c commands (iprobe, imd...) are now compiled in again,
+ even when the i2c command tree is enabled via the CONFIG_I2C_CMD_TREE
+ config option.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 5da048adf44bea5e3b94080d02903c2e3fe7aa4a
+Author: Michal Simek <monstr@monstr.eu>
+Date: Tue Mar 27 00:32:16 2007 +0200
+
+ PATCH: Resolve GPL license problem
+
+commit 1798049522f594013aea29457d46794298c6ae15
+Author: Michal Simek <root@monstr.eu>
+Date: Mon Mar 26 01:39:07 2007 +0200
+
+ Support for XUPV2P board
+ Reset support
+ BSP autoconfig support
+
+commit 0d974d5297349504a2ddfa09314be573b5df320a
+Author: Stefan Roese <sr@denx.de>
+Date: Sat Mar 24 15:57:09 2007 +0100
+
+ [PATCH] Add 4xx GPIO functions
+
+ This patch adds some 4xx GPIO functions. It also moves some of the
+ common code and defines into a common 4xx GPIO header file.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 2db633658bbf366ab0c8dad7a0727e1fb2ae6b11
+Author: Stefan Roese <sr@denx.de>
+Date: Sat Mar 24 15:55:58 2007 +0100
+
+ [PATCH] Small Sequoia cleanup
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 3cb86f3e40d2a80356177434a99f75bc8baa9caf
+Author: Stefan Roese <sr@denx.de>
+Date: Sat Mar 24 15:45:34 2007 +0100
+
+ [PATCH] Clean up 40EZ/Acadia support
+
+ This patch cleans up all the open issue of the preliminary
+ Acadia support.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 6eb1df835191d8ce4b81d5af40fa8e0fbe78e997
+Author: Jon Loeliger <jdl@freescale.com>
+Date: Tue Dec 12 11:02:20 2006 -0600
+
+ Fix 8641HPCN problem with ld version 2.16
+
+ (Dot outside sections problem).
+
+ This fix is in the spirit of 807d5d7319330e336ab34a5623c5e0d73b87d540.
+
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 9964a4dd0d4ef5a037febaebf1aa494b1a72991c
+Author: Haiying Wang <haiying.wang@freescale.com>
+Date: Thu Dec 7 10:35:55 2006 -0600
+
+ Set Rev 2.x 86xx PIC in mixed mode.
+
+ Prevent false interrupt from hanging Linux as MSR[EE] is set
+ to enable interrupts by changing the PIC out of the default
+ pass through mode into mixed mode.
+
+ Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 5a58a73ceb0a4059c42ef64cedbc1a45e0aaa00e
+Author: Jason Jin <jason.jin@freescale.com>
+Date: Thu Dec 7 10:32:35 2006 -0600
+
+ Add flash cmd function to 8641HPCN ramboot
+
+ Also fixes some commmand for 8641 HPCN ramboot case.
+
+ Signed-off-by: Jason Jin <jason.jin@freescale.com>
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 2ccceacc04b009d923afb7c26189ba2f8a2a5d46
+Author: Ed Swarthout <ed.swarthout@freescale.com>
+Date: Thu Dec 7 10:34:14 2006 -0600
+
+ Add support for 8641 Rev 2 silicon.
+
+ Without this patch, I am unable to get to the prompt on rev 2 silicon.
+ Only set ddrioovcr for rev1.
+
+ Signed-off-by: Ed Swarthout<ed.swarthout@freescale.com>
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 44ba464b99001f8bd1c456a1e9d59726252f707a
+Author: Wolfgang Denk <wd@denx.de>
+Date: Thu Mar 22 00:13:12 2007 +0100
+
+ Code cleanup / re-insert previous Copyright entries.
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
commit 2a8dfe08359a1b663418b2faa1da1d7bce34d302
Author: Wolfgang Denk <wd@denx.de>
Date: Wed Mar 21 23:26:15 2007 +0100
@@ -148,6 +834,38 @@
[Blackfin][PATCH] code cleanup
+commit cfc67116a706fd18b8f6a9c11a16753c5626d689
+Author: Michal Simek <monstr@monstr.eu>
+Date: Sun Mar 11 13:48:24 2007 +0100
+
+ [Microblaze][PATCH] part 2
+ timer support
+ interrupt controller support
+ flash support
+ ethernet support
+ cache support
+ board information support
+ env support
+ booting image support
+
+ adding support for Xilinx ML401
+
+commit 76316a318de91f6184e7c22a10e02d275ade2441
+Author: Michal Simek <monstr@monstr.eu>
+Date: Sun Mar 11 13:42:58 2007 +0100
+
+ [Microblaze][PATCH]
+ timer support
+ interrupt controller support
+ flash support
+ ethernet support
+ cache support
+ board information support
+ env support
+ booting image support
+
+ adding support for Xilinx ML401
+
commit 8db13d63157811c839d15a313d9f2d2f5fd10af3
Author: Aubrey Li <aubrey.adi@gmail.com>
Date: Sat Mar 10 23:49:29 2007 +0800
@@ -358,6 +1076,12 @@
Signed-off-by: Stefan Roese <sr@denx.de>
+commit 647d3c3eed0da1d1505eecabe0b0fab96f956e68
+Author: Wolfgang Denk <wd@pollux.denx.de>
+Date: Sun Mar 4 01:36:05 2007 +0100
+
+ Some code cleanup.
+
commit 781e026c8aa6f7e9eb5f0e72cc4d20971219b148
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Wed Feb 28 00:02:04 2007 -0600
@@ -1229,6 +1953,15 @@
[ColdFire MCF5271 family] Add CPU detection based on the value of Chip
Identification Register (CIR).
+commit fdef388758506765d4d6a7155c8f1584c63ff581
+Author: roy zang <tie-fei.zang@freescale.com>
+Date: Mon Jan 22 13:19:21 2007 +0800
+
+ use CFG_WRITE_SWAPPED_DATA define instead of define CFG_FLASH_CFI_SWAP
+ The patch by Heiko Schocher <hs@pollux.denx.de> on Jan, 19, 2007
+ fixes cfi_driver bug for mpc7448hpc2 board. The default cfi_driver can support
+ mpc7448hpc2 board.
+
commit a4012396645533aef218354eeba754dff0deace8
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Fri Jan 19 23:08:39 2007 +0100
@@ -1644,6 +2377,72 @@
automatic update mechanism
+commit 9d27b3a0685ff99fc477983f315c04d49f657a8a
+Author: roy zang <tie-fei.zang@freescale.com>
+Date: Mon Dec 4 17:56:59 2006 +0800
+
+ Slight code clean up.
+ Add comments, delete duplicate define and remove spaces.
+ Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 4dbcd69e3e2776ea334590d5768e3692c5fae5c1
+Author: roy zang <tie-fei.zang@freescale.com>
+Date: Mon Dec 4 17:54:21 2006 +0800
+
+ Introduce PLL_CFG[0:4] table for processor 7448/7447A/7455/7457. The original
+ multiplier table can not refect the real PLL clock behavior of these
+ processors. Please refer to the hardware specification for detailed
+ information of the corresponding processors.
+ Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 4efe20c9579011d9987f62ed7d35ee8cdc1cf0e0
+Author: roy zang <tie-fei.zang@freescale.com>
+Date: Mon Dec 4 14:46:23 2006 +0800
+
+ Remove the static MAC address, ip address, server ip, netmask and
+ gateway ip for network setting.
+ Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 6f12c61cf31ed73d72ddfcfc712a854a3a177aaf
+Author: roy zang <tie-fei.zang@freescale.com>
+Date: Mon Dec 4 14:33:08 2006 +0800
+
+ Remove the duplicate memory test code for mpc744ihpc2 board.
+ If a memory test is needed, please use the functions in
+ post/memory.c or memtest command.
+ Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit c9c1eeed7dd193fa65fb194654132040d49d4d3a
+Author: roy zang <tie-fei.zang@freescale.com>
+Date: Fri Dec 1 19:01:25 2006 +0800
+
+ Fix the exception occuring in RAM table search issue.
+ The original search_one_table() function code can only processes the search
+ for the exception occurring in FLASH/ROM, because the exception and fixup
+ table usually locate in FLASH. If the exception address is also in
+ FLASH, it will be OK.
+ If the exception occurs in RAM, after the u-boot relocation, a
+ relocation offset should be added.
+
+ clean up the code in cpu/74xx_7xx/cpu.c
+
+ Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit ee311214e0d216f904feea269599d0934bf71f23
+Author: roy zang <tie-fei.zang@freescale.com>
+Date: Fri Dec 1 11:47:36 2006 +0800
+
+ Clean up the code according to codestyle:
+ (1) remove some C++ comments.
+ (2) remove trailing white space.
+ (3) remove trailing empty line.
+ (4) Indentation by table.
+ (5) remove {} in one line condition.
+ (6) add space before '(' in function call.
+ Remove some weird printf () output.
+ Add necessary comments.
+ Modified Makefile to support building in a separate directory.
+
commit dd520bf314c7add4183c5191692180f576f96b60
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Thu Nov 30 18:02:20 2006 +0100
@@ -2350,12 +3149,191 @@
Signed-off-by: Nick Spence <nick.spence@freescale.com>
+commit 4831c8b8a97799da77923d6bbb4c260c0d45521c
+Author: roy zang <tie-fei.zang@freescale.com>
+Date: Fri Nov 3 13:10:00 2006 +0800
+
+ Remove some unused CFG define.
+ undef CFG_DRAM_TEST
+
+commit 99c09c4dec34f77c243bf51bea532e3f339410ad
+Author: roy zang <tie-fei.zang@freescale.com>
+Date: Fri Nov 3 13:07:36 2006 +0800
+
+ Change the TEXT_BASE from 0xFFF00000 to 0xFF000000.
+ Both work. 0xFF000000 seems more reasonable.
+
commit c59200443072353044aa4bf737a5a60f9a9af231
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Thu Nov 2 15:15:01 2006 +0100
Release U-Boot 1.1.6
+commit c1fbe4103a0d6c8957f912af902d705ba67836f2
+Author: roy zang <tie-fei.zang@freescale.com>
+Date: Thu Nov 2 19:14:48 2006 +0800
+
+ This patch comes from Yuli's posted patch on 8/8/2006
+ titled "CFI Driver Little-Endian write Issue".
+
+ http://sourceforge.net/mailarchive/message.php?msg_id=36311999
+
+ If that patch applied, please discard this one.
+ Until now , I do not see his patch is applied. So please apply this one.
+
+ Signed-off-by: Yuli Barcohen <yuli@arabellasw.com>
+ Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit b825f158e449e1e9cf74c08e572955e122394c96
+Author: roy zang <tie-fei.zang@freescale.com>
+Date: Thu Nov 2 19:12:31 2006 +0800
+
+ Tsi108 on chip i2c support.
+
+ The i2c Interface provides a master-only, serial interface that can be
+ used for initializing Tsi108/Tsi109 registers from an EEPROM after a
+ device reset.
+
+ Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
+ Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 9226e7d6f09b9a1ac074cd918c81225a4689bba8
+Author: roy zang <tie-fei.zang@freescale.com>
+Date: Thu Nov 2 19:11:06 2006 +0800
+
+ Tsi108 on chip pci controller support.
+
+ If there is no pci card, the tsi108/109 pci configure read will
+ cause a machine check exception to the processor. PCI error should
+ also be cleared after the read.
+
+ Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
+ Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit d1927cee977126e547ceeba23e4f978f377cfb8f
+Author: roy zang <tie-fei.zang@freescale.com>
+Date: Thu Nov 2 19:08:55 2006 +0800
+
+ Tundra tsi108 on chip Ethernet controller support.
+
+ The following is a brief description of the Ethernet controller:
+ The Tsi108/9 Ethernet Controller connects Switch Fabric to two independent
+ Gigabit Ethernet ports,E0 and E1. It uses a single Management interface
+ to manage the two physical connection devices (PHYs). Each Ethernet port
+ has its own statistics monitor that tracks and reports key interface
+ statistics. Each port supports a 256-entry hash table for address
+ filtering. In addition, each port is bridged to the Switch Fabric
+ through a 2-Kbyte transmit FIFO and a 4-Kbyte Receive FIFO.
+
+ Each Ethernet port also has a pair of internal Ethernet DMA channels to
+ support the transmit and receive data flows. The Ethernet DMA channels
+ use descriptors set up in memory, the memory map of the device, and
+ access via the Switch Fabric. The Ethernet Controller?s DMA arbiter
+ handles arbitration for the Switch Fabric. The Controller also
+ has a register businterface for register accesses and status monitor
+ control.
+
+ The PMD (Physical Media Device) interface operates in MII, GMII, or TBI
+ modes. The MII mode is used for connecting with 10 or 100 Mbit/s PMDs.
+ The GMII and TBI modes are used to connect with Gigabit PMDs. Internal
+ data flows to and from the Ethernet Controller through the Switch Fabric.
+
+ Each Ethernet port uses its transmit and receive DMA channels to manage
+ data flows through buffer descriptors that are predefined by the
+ system (the descriptors can exist anywhere in the system memory map).
+ These descriptors are data structures that point to buffers filled
+ with data ready to transmit over Ethernet, or they point to empty
+ buffers ready to receive data from Ethernet.
+
+ Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
+ Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 78aa0c3427f3ecdeb34aabfbbe2dd23b6ad8f40e
+Author: roy zang <tie-fei.zang@freescale.com>
+Date: Thu Nov 2 19:01:33 2006 +0800
+
+ Tundra tsi108 header file.
+
+ The Tundra Semiconductor Corporation (Tundra) Tsi108 is a host bridge for
+ PowerPC processors that offers numerous system interconnect options for
+ embedded application designers. The Tsi108 can interconnect 60x or
+ MPX processors to PCI/X peripherals, DDR2-400 memory, Gigabit Ethernet,
+ and Flash. Provided the macro define for tsi108 chip.
+
+ Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
+ Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 87c4db09699c6b89176b31004afcb83eb1585d47
+Author: roy zang <tie-fei.zang@freescale.com>
+Date: Thu Nov 2 18:59:15 2006 +0800
+
+ Add mpc7448hpc2 (mpc7448 + tsi108) board associated code support.
+ mpc7448hpc2 board support high level code:tsi108 init + mpc7448hpc2.
+
+ Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
+ Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 27801b8ab11c61b577e45742a515bb3b23b80241
+Author: roy zang <tie-fei.zang@freescale.com>
+Date: Thu Nov 2 18:57:21 2006 +0800
+
+ Add mpc7448hpc2 (mpc7448 + tsi108) board associated code support.
+ Make ,config.mk and link file for the mpc7448hpc2 board.
+
+ Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
+ Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit c6411c0c3bbc79f9ba8aef58296a42d8f9d8a0a6
+Author: roy zang <tie-fei.zang@freescale.com>
+Date: Thu Nov 2 18:55:04 2006 +0800
+
+ Add mpc7448hpc2 (mpc7448 + tsi108) board associated code support.
+ The mpc7448hpc2 board support header file.
+
+ Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
+ Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 625bb5ddb50b243f931262ca8c46956409471917
+Author: roy zang <tie-fei.zang@freescale.com>
+Date: Thu Nov 2 18:52:21 2006 +0800
+
+ Add mpc7448hpc2 (mpc7448 + tsi108) board associated code support.
+ The mpc7448hpc2 board support low level assemble language init code.
+
+ Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
+ Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 4c52783b3d024e153c4972b97332e314bc3bdc46
+Author: roy zang <tie-fei.zang@freescale.com>
+Date: Thu Nov 2 18:49:51 2006 +0800
+
+ General code modification for mpc7448hpc2 board support.
+ 1. Add 7447A and 7448 processor support.
+ 2. Add the following flags.
+
+ CFG_CONFIG_BUS_CLK : If the 74xx bus frequency can be configured dynamically
+ (such as by switch on board), this flag should be set.
+
+ CFG_EXCEPTION_AFTER_RELOCATE: If an exception occurs after the u-boot
+ relocates to RAM, this flag should be set.
+
+ CFG_SERIAL_HANG_IN_EXCEPTION: If the print out function will cause the
+ system hang in exception, this flag should be set.
+
+ There is a design issue for tsi108/109 pci configure read. When pci scan
+ the slots, if there is no pci card, the tsi108/9 will cause a machine
+ check exception for mpc7448 processor.
+
+ Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
+ Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 69366bf42f22d67efce8da3f8c40a43d4a3c2695
+Author: roy zang <tie-fei.zang@freescale.com>
+Date: Thu Nov 2 18:34:47 2006 +0800
+
+ Add README file for mpc7448hpc2 board.
+ Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
commit 25721b5cec2be4bce79cfade17ec8f6aa1e67526
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Wed Nov 1 02:04:38 2006 +0100
diff --git a/CREDITS b/CREDITS
index 0099bd4..7af1b80 100644
--- a/CREDITS
+++ b/CREDITS
@@ -474,3 +474,8 @@
E: timur@freescale.com
D: Support for MPC8349E-mITX
W: www.freescale.com
+
+N: Michal Simek
+E: monstr@monstr.eu
+D: Support for Microblaze, ML401, XUPV2P board
+W: www.monstr.eu
diff --git a/MAINTAINERS b/MAINTAINERS
index 68233cf..2a43848 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -564,6 +564,11 @@
SUZAKU MicroBlaze
+Michal Simek <monstr@monstr.eu>
+
+ ML401 MicroBlaze
+ XUPV2P MicroBlaze
+
#########################################################################
# Coldfire Systems: #
# #
diff --git a/MAKEALL b/MAKEALL
index a02d8c1..0f0ec29 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -155,6 +155,7 @@
LIST_74xx=" \
DB64360 DB64460 EVB64260 P3G4 \
p3m7448 PCIPPC2 PCIPPC6 ZUMA \
+ mpc7448hpc2
"
LIST_7xx=" \
@@ -293,7 +294,7 @@
#########################################################################
LIST_microblaze=" \
- suzaku
+ suzaku ml401 xupv2p
"
#########################################################################
diff --git a/Makefile b/Makefile
index 3f5a70d..9a27bc2 100644
--- a/Makefile
+++ b/Makefile
@@ -149,7 +149,7 @@
CROSS_COMPILE = bfin-uclinux-
endif
ifeq ($(ARCH),avr32)
-CROSS_COMPILE = avr32-
+CROSS_COMPILE = avr32-linux-
endif
endif
endif
@@ -430,6 +430,7 @@
@$(MKCONFIG) inka4x0 ppc mpc5xxx inka4x0
lite5200b_config \
+lite5200b_PM_config \
lite5200b_LOWBOOT_config: unconfig
@mkdir -p $(obj)include
@mkdir -p $(obj)board/icecube
@@ -438,6 +439,10 @@
@ echo "... DDR memory revision"
@ echo "#define CONFIG_MPC5200" >>$(obj)include/config.h
@ echo "#define CONFIG_LITE5200B" >>$(obj)include/config.h
+ @[ -z "$(findstring _PM_,$@)" ] || \
+ { echo "#define CONFIG_LITE5200B_PM" >>$(obj)include/config.h ; \
+ echo "... with power management (low-power mode) support" ; \
+ }
@[ -z "$(findstring LOWBOOT_,$@)" ] || \
{ echo "TEXT_BASE = 0xFF000000" >$(obj)board/icecube/config.tmp ; \
echo "... with LOWBOOT configuration" ; \
@@ -1190,44 +1195,31 @@
}
@$(MKCONFIG) -a $(call xtract_4xx,$@) ppc ppc4xx PPChameleonEVB dave
-rainier_config: unconfig
- @mkdir -p $(obj)include
- @echo "#define CONFIG_RAINIER" > $(obj)include/config.h
- @$(MKCONFIG) -n $@ -a sequoia ppc ppc4xx sequoia amcc
-
-rainier_nand_config: unconfig
- @mkdir -p $(obj)include
- @mkdir -p $(obj)nand_spl
- @mkdir -p $(obj)board/amcc/sequoia
- @echo "#define CONFIG_RAINIER" > $(obj)include/config.h
- @echo "#define CONFIG_NAND_U_BOOT" >> $(obj)include/config.h
- @echo "Compile NAND boot image for sequoia"
- @$(MKCONFIG) -n $@ -a sequoia ppc ppc4xx sequoia amcc
- @echo "TEXT_BASE = 0x01000000" > $(obj)board/amcc/sequoia/config.tmp
- @echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
-
sbc405_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc ppc4xx sbc405
-sequoia_config: unconfig
- @$(MKCONFIG) $(@:_config=) ppc ppc4xx sequoia amcc
+sequoia_config \
+rainier_config: unconfig
+ @mkdir -p $(obj)include
+ @echo "#define CONFIG_$$(echo $(subst ,,$(@:_config=)) | \
+ tr '[:lower:]' '[:upper:]')" >$(obj)include/config.h
+ @$(MKCONFIG) -n $@ -a sequoia ppc ppc4xx sequoia amcc
-sequoia_nand_config: unconfig
+sequoia_nand_config \
+rainier_nand_config: unconfig
@mkdir -p $(obj)include
@mkdir -p $(obj)nand_spl
@mkdir -p $(obj)board/amcc/sequoia
@echo "#define CONFIG_NAND_U_BOOT" > $(obj)include/config.h
- @echo "Compile NAND boot image for sequoia"
- @$(MKCONFIG) -a sequoia ppc ppc4xx sequoia amcc
+ @echo "#define CONFIG_$$(echo $(subst ,,$(@:_config=)) | \
+ tr '[:lower:]' '[:upper:]')" >> $(obj)include/config.h
+ @$(MKCONFIG) -n $@ -a sequoia ppc ppc4xx sequoia amcc
@echo "TEXT_BASE = 0x01000000" > $(obj)board/amcc/sequoia/config.tmp
@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
sc3_config:unconfig
@./mkconfig $(@:_config=) ppc ppc4xx sc3
-sycamore_config: unconfig
- @$(MKCONFIG) -n $@ -a walnut ppc ppc4xx walnut amcc
-
taishan_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc ppc4xx taishan amcc
@@ -1244,8 +1236,10 @@
W7OLMG_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc ppc4xx w7o
-walnut_config: unconfig
- @$(MKCONFIG) $(@:_config=) ppc ppc4xx walnut amcc
+# Walnut & Sycamore images are identical (recognized via PVR)
+walnut_config \
+sycamore_config: unconfig
+ @$(MKCONFIG) -n $@ -a walnut ppc ppc4xx walnut amcc
WUH405_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc ppc4xx wuh405 esd
@@ -1253,12 +1247,11 @@
XPEDITE1K_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc ppc4xx xpedite1k
-yosemite_config: unconfig
- @$(MKCONFIG) $(@:_config=) ppc ppc4xx yosemite amcc
-
-yellowstone_config: unconfig
+yosemite_config \
+yellowstone_config: unconfig
@mkdir -p $(obj)include
- @echo "#define CONFIG_YELLOWSTONE" > $(obj)include/config.h
+ @echo "#define CONFIG_$$(echo $(subst ,,$(@:_config=)) | \
+ tr '[:lower:]' '[:upper:]')" >$(obj)include/config.h
@$(MKCONFIG) -n $@ -a yosemite ppc ppc4xx yosemite amcc
yucca_config: unconfig
@@ -1826,6 +1819,9 @@
EVB64260_750CX_config: unconfig
@$(MKCONFIG) EVB64260 ppc 74xx_7xx evb64260
+mpc7448hpc2_config: unconfig
+ @$(MKCONFIG) $(@:_config=) ppc 74xx_7xx mpc7448hpc2
+
P3G4_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc 74xx_7xx evb64260
@@ -2358,6 +2354,16 @@
@echo "#define CONFIG_SUZAKU 1" >> $(obj)include/config.h
@$(MKCONFIG) -a $(@:_config=) microblaze microblaze suzaku AtmarkTechno
+ml401_config: unconfig
+ @ >include/config.h
+ @echo "#define CONFIG_ML401 1" >> include/config.h
+ @./mkconfig -a $(@:_config=) microblaze microblaze ml401 xilinx
+
+xupv2p_config: unconfig
+ @ >include/config.h
+ @echo "#define CONFIG_XUPV2P 1" >> include/config.h
+ @./mkconfig -a $(@:_config=) microblaze microblaze xupv2p xilinx
+
#########################################################################
## Blackfin
#########################################################################
diff --git a/README b/README
index 1542864..90ef2c2 100644
--- a/README
+++ b/README
@@ -164,6 +164,7 @@
- lib_mips Files generic to MIPS architecture
- lib_nios Files generic to NIOS architecture
- lib_ppc Files generic to PowerPC architecture
+- libfdt Library files to support flattened device trees
- net Networking code
- post Power On Self Test
- rtc Real Time Clock drivers
@@ -430,12 +431,23 @@
expect it to be in bytes, others in MB.
Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
- CONFIG_OF_FLAT_TREE
+ CONFIG_OF_LIBFDT / CONFIG_OF_FLAT_TREE
New kernel versions are expecting firmware settings to be
- passed using flat open firmware trees.
- The environment variable "disable_of", when set, disables this
- functionality.
+ passed using flattened device trees (based on open firmware
+ concepts).
+
+ CONFIG_OF_LIBFDT
+ * New libfdt-based support
+ * Adds the "fdt" command
+ * The bootm command does _not_ modify the fdt
+
+ CONFIG_OF_FLAT_TREE
+ * Deprecated, see CONFIG_OF_LIBFDT
+ * Original ft_build.c-based support
+ * Automatically modifies the dft as part of the bootm command
+ * The environment variable "disable_of", when set,
+ disables this functionality.
CONFIG_OF_FLAT_TREE_MAX_SIZE
@@ -448,13 +460,16 @@
CONFIG_OF_HAS_BD_T
- The resulting flat device tree will have a copy of the bd_t.
- Space should be pre-allocated in the dts for the bd_t.
+ * CONFIG_OF_LIBFDT - enables the "fdt bd_t" command
+ * CONFIG_OF_FLAT_TREE - The resulting flat device tree
+ will have a copy of the bd_t. Space should be
+ pre-allocated in the dts for the bd_t.
CONFIG_OF_HAS_UBOOT_ENV
- The resulting flat device tree will have a copy of u-boot's
- environment variables
+ * CONFIG_OF_LIBFDT - enables the "fdt bd_t" command
+ * CONFIG_OF_FLAT_TREE - The resulting flat device tree
+ will have a copy of u-boot's environment variables
CONFIG_OF_BOARD_SETUP
@@ -721,6 +736,8 @@
#define CONFIG_COMMANDS (CFG_CMD_ALL & ~CFG_CMD_NET)
+ Other Commands:
+ fdt (flattened device tree) command: CONFIG_OF_LIBFDT
Note: Don't enable the "icache" and "dcache" commands
(configuration option CFG_CMD_CACHE) unless you know
@@ -2381,17 +2398,17 @@
csb272_config lwmon_config sbc8260_config
CU824_config MBX860T_config sbc8560_33_config
DUET_ADS_config MBX_config sbc8560_66_config
- EBONY_config MPC8260ADS_config SM850_config
- ELPT860_config MPC8540ADS_config SPD823TS_config
- ESTEEM192E_config MPC8540EVAL_config stxgp3_config
- ETX094_config MPC8560ADS_config SXNI855T_config
- FADS823_config NETVIA_config TQM823L_config
- FADS850SAR_config omap1510inn_config TQM850L_config
- FADS860T_config omap1610h2_config TQM855L_config
- FPS850L_config omap1610inn_config TQM860L_config
- omap5912osk_config walnut_config
- omap2420h4_config Yukon8220_config
- ZPC1900_config
+ EBONY_config mpc7448hpc2_config SM850_config
+ ELPT860_config MPC8260ADS_config SPD823TS_config
+ ESTEEM192E_config MPC8540ADS_config stxgp3_config
+ ETX094_config MPC8540EVAL_config SXNI855T_config
+ FADS823_config NMPC8560ADS_config TQM823L_config
+ FADS850SAR_config NETVIA_config TQM850L_config
+ FADS860T_config omap1510inn_config TQM855L_config
+ FPS850L_config omap1610h2_config TQM860L_config
+ omap1610inn_config walnut_config
+ omap5912osk_config Yukon8220_config
+ omap2420h4_config ZPC1900_config
Note: for some board special configuration names may exist; check if
additional information is available from the board vendor; for
diff --git a/avr32_config.mk b/avr32_config.mk
index 0b92053..441caa4 100644
--- a/avr32_config.mk
+++ b/avr32_config.mk
@@ -21,5 +21,5 @@
# MA 02111-1307 USA
#
-PLATFORM_RELFLAGS += -ffixed-r5 -mno-pic -mrelax
+PLATFORM_RELFLAGS += -ffixed-r5 -fPIC -mno-init-got -mrelax
PLATFORM_LDFLAGS += --relax
diff --git a/board/AtmarkTechno/suzaku/suzaku.c b/board/AtmarkTechno/suzaku/suzaku.c
index afe124a..267c476 100644
--- a/board/AtmarkTechno/suzaku/suzaku.c
+++ b/board/AtmarkTechno/suzaku/suzaku.c
@@ -24,7 +24,7 @@
/* This is a board specific file. It's OK to include board specific
* header files */
-#include <asm/suzaku.h>
+#include <config.h>
void do_reset(void)
{
diff --git a/board/AtmarkTechno/suzaku/u-boot.lds b/board/AtmarkTechno/suzaku/u-boot.lds
index 00a8ef7..cb90854 100644
--- a/board/AtmarkTechno/suzaku/u-boot.lds
+++ b/board/AtmarkTechno/suzaku/u-boot.lds
@@ -61,6 +61,7 @@
{
__bss_start = .;
*(.bss)
- __bss_start = .;
+ __bss_end = .;
}
+ __end = . ;
}
diff --git a/board/amcc/acadia/Makefile b/board/amcc/acadia/Makefile
index 183f694..abcbf3e 100644
--- a/board/amcc/acadia/Makefile
+++ b/board/amcc/acadia/Makefile
@@ -23,25 +23,29 @@
include $(TOPDIR)/config.mk
-LIB = lib$(BOARD).a
+LIB = $(obj)lib$(BOARD).a
-OBJS = $(BOARD).o cpr.o memory.o
+COBJS = $(BOARD).o cpr.o memory.o
SOBJS =
-$(LIB): $(OBJS) $(SOBJS)
- $(AR) crv $@ $(OBJS) $(SOBJS)
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
clean:
rm -f $(SOBJS) $(OBJS)
distclean: clean
- rm -f $(LIB) core *.bak .depend
+ rm -f $(LIB) core *.bak .depend *~
#########################################################################
-.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
- $(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
-sinclude .depend
+sinclude $(obj).depend
#########################################################################
diff --git a/board/amcc/acadia/acadia.c b/board/amcc/acadia/acadia.c
index c8aaad2..baf598c 100644
--- a/board/amcc/acadia/acadia.c
+++ b/board/amcc/acadia/acadia.c
@@ -26,10 +26,7 @@
extern void board_pll_init_f(void);
-/* Some specific Acadia Defines */
-#define CPLD_BASE 0x80000000
-
-void liveoak_gpio_init(void)
+static void acadia_gpio_init(void)
{
/*
* GPIO0 setup (select GPIO or alternate function)
@@ -54,62 +51,16 @@
out32(GPIO1_TCR, CFG_GPIO1_TCR); /* enable output driver for outputs */
}
-#if 0 /* test-only: not called at all??? */
-void ext_bus_cntlr_init(void)
-{
-#if (defined(EBC_PB4AP) && defined(EBC_PB4CR) && !(CFG_INIT_DCACHE_CS == 4))
- mtebc(pb4ap, EBC_PB4AP);
- mtebc(pb4cr, EBC_PB4CR);
-#endif
-}
-#endif
-
int board_early_init_f(void)
{
unsigned int reg;
-#if 0 /* test-only */
- /*
- * If CRAM memory and SPI/NAND boot, and if the CRAM memory is
- * already initialized by the pre-loader then we can't reinitialize
- * CPR registers, GPIO registers and EBC registers as this will
- * have the effect of un-initializing CRAM.
- */
- spr_reg = (volatile unsigned long) mfspr(SPRG7);
- if (spr_reg != LOAK_CRAM) { /* != CRAM */
+ /* don't reinit PLL when booting via I2C bootstrap option */
+ mfsdr(SDR_PINSTP, reg);
+ if (reg != 0xf0000000)
board_pll_init_f();
- liveoak_gpio_init();
- ext_bus_cntlr_init();
-
- mtebc(pb1ap, CFG_EBC_PB1AP);
- mtebc(pb1cr, CFG_EBC_PB1CR);
- mtebc(pb2ap, CFG_EBC_PB2AP);
- mtebc(pb2cr, CFG_EBC_PB2CR);
- }
-#else
- board_pll_init_f();
- liveoak_gpio_init();
-/* ext_bus_cntlr_init(); */
-#endif
-
-#if 0 /* test-only (orig) */
- /*
- * If we boot from NAND Flash, we are running in
- * RAM, so disable the EBC_CS0 so that it goes back
- * to the NOR Flash. It will be enabled later
- * for the NAND Flash on EBC_CS1
- */
- mfsdr(sdrultra0, reg);
- mtsdr(sdrultra0, reg & ~SDR_ULTRA0_CSNSEL0);
-#endif
-#if 0 /* test-only */
- /* configure for NAND */
- mfsdr(sdrultra0, reg);
- reg &= ~SDR_ULTRA0_CSN_MASK;
- reg |= SDR_ULTRA0_CSNSEL0 >> CFG_NAND_CS;
- mtsdr(sdrultra0, reg & ~SDR_ULTRA0_CSNSEL0);
-#endif
+ acadia_gpio_init();
/* USB Host core needs this bit set */
mfsdr(sdrultra1, reg);
@@ -128,7 +79,7 @@
int misc_init_f(void)
{
/* Set EPLD to take PHY out of reset */
- out8(CPLD_BASE + 0x05, 0x00);
+ out8(CFG_CPLD_BASE + 0x05, 0x00);
udelay(100000);
return 0;
diff --git a/board/amcc/acadia/config.mk b/board/amcc/acadia/config.mk
index ce21374..c8566ec 100644
--- a/board/amcc/acadia/config.mk
+++ b/board/amcc/acadia/config.mk
@@ -1,5 +1,5 @@
#
-# (C) Copyright 2000
+# (C) Copyright 2007
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# See file CREDITS for list of people who contributed to this
@@ -21,21 +21,10 @@
# MA 02111-1307 USA
#
-sinclude $(TOPDIR)/board/amcc/liveoak/config.tmp
-
ifndef TEXT_BASE
TEXT_BASE = 0xFFFC0000
endif
-ifeq ($(CONFIG_NAND_U_BOOT),y)
-LDSCRIPT = $(TOPDIR)/board/$(BOARDDIR)/u-boot-nand.lds
-endif
-
-ifeq ($(CONFIG_SPI_U_BOOT),y)
-LDSCRIPT = $(TOPDIR)/board/$(BOARDDIR)/u-boot-spi.lds
-PAD_TO = 0x00840000
-endif
-
ifeq ($(debug),1)
PLATFORM_CPPFLAGS += -DDEBUG
endif
diff --git a/board/amcc/acadia/cpr.c b/board/amcc/acadia/cpr.c
index 23b9e12..9dcce35 100644
--- a/board/amcc/acadia/cpr.c
+++ b/board/amcc/acadia/cpr.c
@@ -76,19 +76,19 @@
* | UART0 | 28.57 | 7 (0x07)|
* | UART1 | 28.57 | 7 (0x07)|
* | DAC | 28.57 | 7 (0xA7)|
- * | ADC | 4 | 50 (0x32)|
+ * | ADC | 4 | 50 (0x32)|
* | PWM | 28.57 | 7 (0x07)|
* | EMAC | 4 | 50 (0x32)|
* -----------------------------------
*/
/* Initialize PLL */
- mtcpr(cprpllc, 0x20000238);
- mtcpr(cprplld, 0x03010400);
+ mtcpr(cprpllc, 0x20000238);
+ mtcpr(cprplld, 0x03010400);
mtcpr(cprprimad, 0x03050a0a);
- mtcpr(cprperc0, 0x00000000);
- mtcpr(cprperd0, 0x070a0707); /* SPI clk div. eq. OPB clk div. */
- mtcpr(cprperd1, 0x07323200);
+ mtcpr(cprperc0, 0x00000000);
+ mtcpr(cprperd0, 0x070a0707); /* SPI clk div. eq. OPB clk div. */
+ mtcpr(cprperd1, 0x07323200);
mtcpr(cprclkupd, 0x40000000);
}
@@ -117,11 +117,11 @@
*/
/* Initialize PLL */
- mtcpr(cprpllc, 0x0000033C);
- mtcpr(cprplld, 0x0a010000);
+ mtcpr(cprpllc, 0x0000033C);
+ mtcpr(cprplld, 0x0a010000);
mtcpr(cprprimad, 0x02040808);
- mtcpr(cprperd0, 0x02080505); /* SPI clk div. eq. OPB clk div. */
- mtcpr(cprperd1, 0xA6A60300);
+ mtcpr(cprperd0, 0x02080505); /* SPI clk div. eq. OPB clk div. */
+ mtcpr(cprperd1, 0xA6A60300);
mtcpr(cprclkupd, 0x40000000);
}
@@ -143,20 +143,20 @@
*/
/* Initialize PLL */
- mtcpr(cprpllc, 0x000003BC);
- mtcpr(cprplld, 0x06060600);
+ mtcpr(cprpllc, 0x000003BC);
+ mtcpr(cprplld, 0x06060600);
mtcpr(cprprimad, 0x02020004);
- mtcpr(cprperd0, 0x04002828); /* SPI clk div. eq. OPB clk div. */
- mtcpr(cprperd1, 0xC8C81600);
+ mtcpr(cprperd0, 0x04002828); /* SPI clk div. eq. OPB clk div. */
+ mtcpr(cprperd1, 0xC8C81600);
mtcpr(cprclkupd, 0x40000000);
}
-#endif /* CPU_<speed>_405EZ */
+#endif /* CPU_<speed>_405EZ */
#if defined(CONFIG_NAND_SPL) || defined(CONFIG_SPI_SPL)
/*
* Get timebase clock frequency
*/
-unsigned long get_tbclk (void)
+unsigned long get_tbclk(void)
{
unsigned long cpr_plld;
unsigned long cpr_primad;
@@ -192,4 +192,4 @@
return (freqProcessor);
}
-#endif /* defined(CONFIG_NAND_SPL) || defined(CONFIG_SPI_SPL) */
+#endif /* defined(CONFIG_NAND_SPL) || defined(CONFIG_SPI_SPL) */
diff --git a/board/amcc/acadia/flash.c b/board/amcc/acadia/flash.c
deleted file mode 100644
index 0626aba..0000000
--- a/board/amcc/acadia/flash.c
+++ /dev/null
@@ -1,1108 +0,0 @@
-/*
- * (C) Copyright 2004-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2002 Jun Gu <jung@artesyncp.com>
- * Add support for Am29F016D and dynamic switch setting.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * Modified 4/5/2001
- * Wait for completion of each sector erase command issued
- * 4/5/2001
- * Chris Hallinan - DS4.COM, Inc. - clh@net1plus.com
- */
-
-#include <common.h>
-#include <ppc4xx.h>
-#include <asm/processor.h>
-
-#ifdef DEBUG
-#define DEBUGF(x...) printf(x)
-#else
-#define DEBUGF(x...)
-#endif /* DEBUG */
-
-flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-/*
- * Mark big flash bank (16 bit instead of 8 bit access) in address with bit 0
- */
-static unsigned long flash_addr_table[][CFG_MAX_FLASH_BANKS] = {
- {0xffc00001}, /* 0:boot from big flash */
-};
-
-/*
- * include common flash code (for amcc boards)
- */
-/*-----------------------------------------------------------------------
- * Functions
- */
-static int write_word(flash_info_t * info, ulong dest, ulong data);
-#ifdef CFG_FLASH_2ND_16BIT_DEV
-static int write_word_1(flash_info_t * info, ulong dest, ulong data);
-static int write_word_2(flash_info_t * info, ulong dest, ulong data);
-static int flash_erase_1(flash_info_t * info, int s_first, int s_last);
-static int flash_erase_2(flash_info_t * info, int s_first, int s_last);
-static ulong flash_get_size_1(vu_long * addr, flash_info_t * info);
-static ulong flash_get_size_2(vu_long * addr, flash_info_t * info);
-#endif
-
-void flash_print_info(flash_info_t * info)
-{
- int i;
- int k;
- int size;
- int erased;
- volatile unsigned long *flash;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_AMD:
- printf("AMD ");
- break;
- case FLASH_MAN_STM:
- printf("STM ");
- break;
- case FLASH_MAN_FUJ:
- printf("FUJITSU ");
- break;
- case FLASH_MAN_SST:
- printf("SST ");
- break;
- case FLASH_MAN_MX:
- printf("MIXC ");
- break;
- default:
- printf("Unknown Vendor ");
- break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_AM040:
- printf("AM29F040 (512 Kbit, uniform sector size)\n");
- break;
- case FLASH_AM400B:
- printf("AM29LV400B (4 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM400T:
- printf("AM29LV400T (4 Mbit, top boot sector)\n");
- break;
- case FLASH_AM800B:
- printf("AM29LV800B (8 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM800T:
- printf("AM29LV800T (8 Mbit, top boot sector)\n");
- break;
- case FLASH_AMD016:
- printf("AM29F016D (16 Mbit, uniform sector size)\n");
- break;
- case FLASH_AM160B:
- printf("AM29LV160B (16 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM160T:
- printf("AM29LV160T (16 Mbit, top boot sector)\n");
- break;
- case FLASH_AM320B:
- printf("AM29LV320B (32 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM320T:
- printf("AM29LV320T (32 Mbit, top boot sector)\n");
- break;
- case FLASH_AM033C:
- printf("AM29LV033C (32 Mbit, top boot sector)\n");
- break;
- case FLASH_SST800A:
- printf("SST39LF/VF800 (8 Mbit, uniform sector size)\n");
- break;
- case FLASH_SST160A:
- printf("SST39LF/VF160 (16 Mbit, uniform sector size)\n");
- break;
- case FLASH_STMW320DT:
- printf ("M29W320DT (32 M, top sector)\n");
- break;
- case FLASH_MXLV320T:
- printf ("MXLV320T (32 Mbit, top sector)\n");
- break;
- default:
- printf("Unknown Chip Type\n");
- break;
- }
-
- printf(" Size: %ld KB in %d Sectors\n",
- info->size >> 10, info->sector_count);
-
- printf(" Sector Start Addresses:");
- for (i = 0; i < info->sector_count; ++i) {
- /*
- * Check if whole sector is erased
- */
- if (i != (info->sector_count - 1))
- size = info->start[i + 1] - info->start[i];
- else
- size = info->start[0] + info->size - info->start[i];
- erased = 1;
- flash = (volatile unsigned long *)info->start[i];
- size = size >> 2; /* divide by 4 for longword access */
- for (k = 0; k < size; k++) {
- if (*flash++ != 0xffffffff) {
- erased = 0;
- break;
- }
- }
-
- if ((i % 5) == 0)
- printf("\n ");
- printf(" %08lX%s%s",
- info->start[i],
- erased ? " E" : " ", info->protect[i] ? "RO " : " ");
- }
- printf("\n");
- return;
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-#ifdef CFG_FLASH_2ND_16BIT_DEV
-static ulong flash_get_size(vu_long * addr, flash_info_t * info)
-{
- /* bit 0 used for big flash marking */
- if ((ulong)addr & 0x1) {
- return flash_get_size_2((vu_long *)((ulong)addr & 0xfffffffe), info);
- } else {
- return flash_get_size_1(addr, info);
- }
-}
-
-static ulong flash_get_size_1(vu_long * addr, flash_info_t * info)
-#else
-static ulong flash_get_size(vu_long * addr, flash_info_t * info)
-#endif
-{
- short i;
- CFG_FLASH_WORD_SIZE value;
- ulong base = (ulong) addr;
- volatile CFG_FLASH_WORD_SIZE *addr2 = (CFG_FLASH_WORD_SIZE *) addr;
-
- DEBUGF("FLASH ADDR: %08x\n", (unsigned)addr);
-
- /* Write auto select command: read Manufacturer ID */
- addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
- addr2[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
- addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00900090;
- udelay(1000);
-
- value = addr2[0];
- DEBUGF("FLASH MANUFACT: %x\n", value);
-
- switch (value) {
- case (CFG_FLASH_WORD_SIZE) AMD_MANUFACT:
- info->flash_id = FLASH_MAN_AMD;
- break;
- case (CFG_FLASH_WORD_SIZE) FUJ_MANUFACT:
- info->flash_id = FLASH_MAN_FUJ;
- break;
- case (CFG_FLASH_WORD_SIZE) SST_MANUFACT:
- info->flash_id = FLASH_MAN_SST;
- break;
- case (CFG_FLASH_WORD_SIZE) STM_MANUFACT:
- info->flash_id = FLASH_MAN_STM;
- break;
- default:
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- return (0); /* no or unknown flash */
- }
-
- value = addr2[1]; /* device ID */
- DEBUGF("\nFLASH DEVICEID: %x\n", value);
-
- switch (value) {
- case (CFG_FLASH_WORD_SIZE) AMD_ID_LV040B:
- info->flash_id += FLASH_AM040;
- info->sector_count = 8;
- info->size = 0x0080000; /* => 512 ko */
- break;
-
- case (CFG_FLASH_WORD_SIZE) AMD_ID_F040B:
- info->flash_id += FLASH_AM040;
- info->sector_count = 8;
- info->size = 0x0080000; /* => 512 ko */
- break;
-
- case (CFG_FLASH_WORD_SIZE) STM_ID_M29W040B:
- info->flash_id += FLASH_AM040;
- info->sector_count = 8;
- info->size = 0x0080000; /* => 512 ko */
- break;
-
- case (CFG_FLASH_WORD_SIZE) AMD_ID_F016D:
- info->flash_id += FLASH_AMD016;
- info->sector_count = 32;
- info->size = 0x00200000;
- break; /* => 2 MB */
-
- case (CFG_FLASH_WORD_SIZE) AMD_ID_LV033C:
- info->flash_id += FLASH_AMDLV033C;
- info->sector_count = 64;
- info->size = 0x00400000;
- break; /* => 4 MB */
-
- case (CFG_FLASH_WORD_SIZE) AMD_ID_LV400T:
- info->flash_id += FLASH_AM400T;
- info->sector_count = 11;
- info->size = 0x00080000;
- break; /* => 0.5 MB */
-
- case (CFG_FLASH_WORD_SIZE) AMD_ID_LV400B:
- info->flash_id += FLASH_AM400B;
- info->sector_count = 11;
- info->size = 0x00080000;
- break; /* => 0.5 MB */
-
- case (CFG_FLASH_WORD_SIZE) AMD_ID_LV800T:
- info->flash_id += FLASH_AM800T;
- info->sector_count = 19;
- info->size = 0x00100000;
- break; /* => 1 MB */
-
- case (CFG_FLASH_WORD_SIZE) AMD_ID_LV800B:
- info->flash_id += FLASH_AM800B;
- info->sector_count = 19;
- info->size = 0x00100000;
- break; /* => 1 MB */
-
- case (CFG_FLASH_WORD_SIZE) AMD_ID_LV160T:
- info->flash_id += FLASH_AM160T;
- info->sector_count = 35;
- info->size = 0x00200000;
- break; /* => 2 MB */
-
- case (CFG_FLASH_WORD_SIZE) AMD_ID_LV160B:
- info->flash_id += FLASH_AM160B;
- info->sector_count = 35;
- info->size = 0x00200000;
- break; /* => 2 MB */
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- return (0); /* => no or unknown flash */
- }
-
- /* set up sector start address table */
- if (((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) ||
- ((info->flash_id & FLASH_TYPEMASK) == FLASH_AM040) ||
- ((info->flash_id & FLASH_TYPEMASK) == FLASH_AMD016)) {
- for (i = 0; i < info->sector_count; i++)
- info->start[i] = base + (i * 0x00010000);
- } else {
- if (info->flash_id & FLASH_BTYPE) {
- /* set sector offsets for bottom boot block type */
- info->start[0] = base + 0x00000000;
- info->start[1] = base + 0x00004000;
- info->start[2] = base + 0x00006000;
- info->start[3] = base + 0x00008000;
- for (i = 4; i < info->sector_count; i++) {
- info->start[i] =
- base + (i * 0x00010000) - 0x00030000;
- }
- } else {
- /* set sector offsets for top boot block type */
- i = info->sector_count - 1;
- info->start[i--] = base + info->size - 0x00004000;
- info->start[i--] = base + info->size - 0x00006000;
- info->start[i--] = base + info->size - 0x00008000;
- for (; i >= 0; i--) {
- info->start[i] = base + i * 0x00010000;
- }
- }
- }
-
- /* check for protected sectors */
- for (i = 0; i < info->sector_count; i++) {
- /* read sector protection at sector address, (A7 .. A0) = 0x02 */
- /* D0 = 1 if protected */
- addr2 = (volatile CFG_FLASH_WORD_SIZE *)(info->start[i]);
-
- /* For AMD29033C flash we need to resend the command of *
- * reading flash protection for upper 8 Mb of flash */
- if (i == 32) {
- addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0xAAAAAAAA;
- addr2[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x55555555;
- addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x90909090;
- }
-
- if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST)
- info->protect[i] = 0;
- else
- info->protect[i] = addr2[2] & 1;
- }
-
- /* issue bank reset to return to read mode */
- addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00F000F0;
-
- return (info->size);
-}
-
-static int wait_for_DQ7_1(flash_info_t * info, int sect)
-{
- ulong start, now, last;
- volatile CFG_FLASH_WORD_SIZE *addr =
- (CFG_FLASH_WORD_SIZE *) (info->start[sect]);
-
- start = get_timer(0);
- last = start;
- while ((addr[0] & (CFG_FLASH_WORD_SIZE) 0x00800080) !=
- (CFG_FLASH_WORD_SIZE) 0x00800080) {
- if ((now = get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
- printf("Timeout\n");
- return -1;
- }
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- putc('.');
- last = now;
- }
- }
- return 0;
-}
-
-#ifdef CFG_FLASH_2ND_16BIT_DEV
-int flash_erase(flash_info_t * info, int s_first, int s_last)
-{
- if (((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320B) ||
- ((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320T) ||
- ((info->flash_id & FLASH_TYPEMASK) == FLASH_STMW320DT) ||
- ((info->flash_id & FLASH_TYPEMASK) == FLASH_MXLV320T)) {
- return flash_erase_2(info, s_first, s_last);
- } else {
- return flash_erase_1(info, s_first, s_last);
- }
-}
-
-static int flash_erase_1(flash_info_t * info, int s_first, int s_last)
-#else
-int flash_erase(flash_info_t * info, int s_first, int s_last)
-#endif
-{
- volatile CFG_FLASH_WORD_SIZE *addr = (CFG_FLASH_WORD_SIZE *) (info->start[0]);
- volatile CFG_FLASH_WORD_SIZE *addr2;
- int flag, prot, sect, l_sect;
- int i;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf("- missing\n");
- } else {
- printf("- no sectors to erase\n");
- }
- return 1;
- }
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf("Can't erase unknown flash type - aborted\n");
- return 1;
- }
-
- prot = 0;
- for (sect = s_first; sect <= s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf("\n");
- }
-
- l_sect = -1;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- addr2 = (CFG_FLASH_WORD_SIZE *) (info->start[sect]);
-
- if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) {
- addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
- addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
- addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00800080;
- addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
- addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
- addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00500050; /* block erase */
- for (i = 0; i < 50; i++)
- udelay(1000); /* wait 1 ms */
- } else {
- addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
- addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
- addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00800080;
- addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
- addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
- addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00300030; /* sector erase */
- }
- l_sect = sect;
- /*
- * Wait for each sector to complete, it's more
- * reliable. According to AMD Spec, you must
- * issue all erase commands within a specified
- * timeout. This has been seen to fail, especially
- * if printf()s are included (for debug)!!
- */
- wait_for_DQ7_1(info, sect);
- }
- }
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* wait at least 80us - let's wait 1 ms */
- udelay(1000);
-
- /* reset to read mode */
- addr = (CFG_FLASH_WORD_SIZE *) info->start[0];
- addr[0] = (CFG_FLASH_WORD_SIZE) 0x00F000F0; /* reset bank */
-
- printf(" done\n");
- return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-int write_buff(flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
- ulong cp, wp, data;
- int i, l, rc;
-
- wp = (addr & ~3); /* get lower word aligned address */
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- data = 0;
- for (i = 0, cp = wp; i < l; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
- for (; i < 4 && cnt > 0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
- for (; cnt == 0 && i < 4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
-
- if ((rc = write_word(info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- }
-
- /*
- * handle word aligned part
- */
- while (cnt >= 4) {
- data = 0;
- for (i = 0; i < 4; ++i) {
- data = (data << 8) | *src++;
- }
- if ((rc = write_word(info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- cnt -= 4;
- }
-
- if (cnt == 0) {
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i = 0, cp = wp; i < 4 && cnt > 0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i < 4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
-
- return (write_word(info, wp, data));
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-#ifdef CFG_FLASH_2ND_16BIT_DEV
-static int write_word(flash_info_t * info, ulong dest, ulong data)
-{
- if (((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320B) ||
- ((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320T) ||
- ((info->flash_id & FLASH_TYPEMASK) == FLASH_STMW320DT) ||
- ((info->flash_id & FLASH_TYPEMASK) == FLASH_MXLV320T)) {
- return write_word_2(info, dest, data);
- } else {
- return write_word_1(info, dest, data);
- }
-}
-
-static int write_word_1(flash_info_t * info, ulong dest, ulong data)
-#else
-static int write_word(flash_info_t * info, ulong dest, ulong data)
-#endif
-{
- volatile CFG_FLASH_WORD_SIZE *addr2 = (CFG_FLASH_WORD_SIZE *) (info->start[0]);
- volatile CFG_FLASH_WORD_SIZE *dest2 = (CFG_FLASH_WORD_SIZE *) dest;
- volatile CFG_FLASH_WORD_SIZE *data2 = (CFG_FLASH_WORD_SIZE *) & data;
- ulong start;
- int i;
-
- /* Check if Flash is (sufficiently) erased */
- if ((*((vu_long *)dest) & data) != data) {
- return (2);
- }
-
- for (i = 0; i < 4 / sizeof(CFG_FLASH_WORD_SIZE); i++) {
- int flag;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
- addr2[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
- addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00A000A0;
-
- dest2[i] = data2[i];
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* data polling for D7 */
- start = get_timer(0);
- while ((dest2[i] & (CFG_FLASH_WORD_SIZE) 0x00800080) !=
- (data2[i] & (CFG_FLASH_WORD_SIZE) 0x00800080)) {
-
- if (get_timer(start) > CFG_FLASH_WRITE_TOUT) {
- return (1);
- }
- }
- }
-
- return (0);
-}
-
-#ifdef CFG_FLASH_2ND_16BIT_DEV
-
-#undef CFG_FLASH_WORD_SIZE
-#define CFG_FLASH_WORD_SIZE unsigned short
-
-/*
- * The following code cannot be run from FLASH!
- */
-static ulong flash_get_size_2(vu_long * addr, flash_info_t * info)
-{
- short i;
- int n;
- CFG_FLASH_WORD_SIZE value;
- ulong base = (ulong) addr;
- volatile CFG_FLASH_WORD_SIZE *addr2 = (CFG_FLASH_WORD_SIZE *) addr;
-
- DEBUGF("FLASH ADDR: %08x\n", (unsigned)addr);
-
- /* issue bank reset to return to read mode */
- addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00F000F0;
- /* Write auto select command: read Manufacturer ID */
- addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
- addr2[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
- addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00900090;
- udelay(1000);
-
- value = addr2[0];
- DEBUGF("FLASH MANUFACT: %x\n", value);
-
-#if 0 /* TODO: remove ifdef when Flash responds correctly */
- switch (value) {
- case (CFG_FLASH_WORD_SIZE) AMD_MANUFACT:
- info->flash_id = FLASH_MAN_AMD;
- break;
- case (CFG_FLASH_WORD_SIZE) FUJ_MANUFACT:
- info->flash_id = FLASH_MAN_FUJ;
- break;
- case (CFG_FLASH_WORD_SIZE) SST_MANUFACT:
- info->flash_id = FLASH_MAN_SST;
- break;
- case (CFG_FLASH_WORD_SIZE) STM_MANUFACT:
- info->flash_id = FLASH_MAN_STM;
- break;
- case (CFG_FLASH_WORD_SIZE) MX_MANUFACT:
- info->flash_id = FLASH_MAN_MX;
- break;
- default:
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- return (0); /* no or unknown flash */
- }
-#endif /* TODO: remove ifdef when Flash responds correctly */
-
- /*
- * TODO: Start
- * uncomment block above when Flash responds correctly.
- * also remove the lines below:
- */
- info->flash_id = FLASH_MAN_AMD;
- DEBUGF("FLASH MANUFACT: FLASH_MAN_AMD\n");
- /* TODO: End */
-
- value = addr2[1]; /* device ID */
-
- DEBUGF("\nFLASH DEVICEID: %x\n", value);
-
-#if 0 /* TODO: remove ifdef when Flash responds correctly */
- switch (value) {
-
- case (CFG_FLASH_WORD_SIZE)AMD_ID_LV320T:
- info->flash_id += FLASH_AM320T;
- info->sector_count = 71;
- info->size = 0x00400000; break; /* => 4 MB */
-
- case (CFG_FLASH_WORD_SIZE)AMD_ID_LV320B:
- info->flash_id += FLASH_AM320B;
- info->sector_count = 71;
- info->size = 0x00400000; break; /* => 4 MB */
-
- case (CFG_FLASH_WORD_SIZE)STM_ID_29W320DT:
- info->flash_id += FLASH_STMW320DT;
- info->sector_count = 67;
- info->size = 0x00400000; break; /* => 4 MB */
-
- case (CFG_FLASH_WORD_SIZE)MX_ID_LV320T:
- info->flash_id += FLASH_MXLV320T;
- info->sector_count = 71;
- info->size = 0x00400000; break; /* => 4 MB */
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- return (0); /* => no or unknown flash */
- }
-#endif /* TODO: remove ifdef when Flash responds correctly */
-
- /*
- * TODO: Start
- * uncomment block above when Flash responds correctly.
- * also remove the lines below:
- */
- DEBUGF("\nFLASH DEVICEID: FLASH_AM320T\n");
- info->flash_id += FLASH_AM320T;
- info->sector_count = 71;
- info->size = 0x00400000; /* => 4 MB */
- /* TODO: End */
-
- /* set up sector start address table */
- if (((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) ||
- ((info->flash_id & FLASH_TYPEMASK) == FLASH_AM040) ||
- ((info->flash_id & FLASH_TYPEMASK) == FLASH_AMD016)) {
- for (i = 0; i < info->sector_count; i++)
- info->start[i] = base + (i * 0x00010000);
- } else if ((info->flash_id & FLASH_TYPEMASK) == FLASH_STMW320DT) {
- /* set sector offsets for top boot block type */
- base += info->size;
- i = info->sector_count;
- /* 1 x 16k boot sector */
- base -= 16 << 10;
- --i;
- info->start[i] = base;
- /* 2 x 8k boot sectors */
- for (n=0; n<2; ++n) {
- base -= 8 << 10;
- --i;
- info->start[i] = base;
- }
- /* 1 x 32k boot sector */
- base -= 32 << 10;
- --i;
- info->start[i] = base;
-
- while (i > 0) { /* 64k regular sectors */
- base -= 64 << 10;
- --i;
- info->start[i] = base;
- }
- } else if ( ((info->flash_id & FLASH_TYPEMASK) == FLASH_MXLV320T) ||
- ((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320T) ) {
- i = info->sector_count - 1;
- info->start[i--] = base + info->size - 0x00002000;
- info->start[i--] = base + info->size - 0x00004000;
- info->start[i--] = base + info->size - 0x00006000;
- info->start[i--] = base + info->size - 0x00008000;
- info->start[i--] = base + info->size - 0x0000a000;
- info->start[i--] = base + info->size - 0x0000c000;
- info->start[i--] = base + info->size - 0x0000e000;
- info->start[i--] = base + info->size - 0x00010000;
- for (; i >= 0; i--) {
- info->start[i] = base + i * 0x00010000;
- }
- }
- else {
- if (info->flash_id & FLASH_BTYPE){
- /* set sector offsets for bottom boot block type */
- info->start[0] = base + 0x00000000;
- info->start[1] = base + 0x00004000;
- info->start[2] = base + 0x00006000;
- info->start[3] = base + 0x00008000;
- for (i = 4; i < info->sector_count; i++) {
- info->start[i] =
- base + (i * 0x00010000) - 0x00030000;
- }
- } else {
- /* set sector offsets for top boot block type */
- i = info->sector_count - 1;
- info->start[i--] = base + info->size - 0x00004000;
- info->start[i--] = base + info->size - 0x00006000;
- info->start[i--] = base + info->size - 0x00008000;
- for (; i >= 0; i--) {
- info->start[i] = base + i * 0x00010000;
- }
- }
- }
-
- /* check for protected sectors */
- for (i = 0; i < info->sector_count; i++) {
- /* read sector protection at sector address,(A7 .. A0) = 0x02 */
- /* D0 = 1 if protected */
- addr2 = (volatile CFG_FLASH_WORD_SIZE *)(info->start[i]);
-
- /* For AMD29033C flash we need to resend the command of *
- * reading flash protection for upper 8 Mb of flash */
- if (i == 32) {
- addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0xAAAAAAAA;
- addr2[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x55555555;
- addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x90909090;
- }
-
- if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST)
- info->protect[i] = 0;
- else
- info->protect[i] = addr2[2] & 1;
- }
-
- /* issue bank reset to return to read mode */
- addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00F000F0;
-
- return (info->size);
-}
-
-/*
- * TODO: FIX: this wait loop sometimes fails: DQ7 indicates the erase command
- * never was accepted (i.e. didn't start) - why????
- */
-static int wait_for_DQ7_2(flash_info_t * info, int sect)
-{
- ulong start, now, last, counter = 0;
- volatile CFG_FLASH_WORD_SIZE *addr =
- (CFG_FLASH_WORD_SIZE *) (info->start[sect]);
-
- start = get_timer(0);
- DEBUGF("DQ7_2: start = 0x%08lx\n", start);
- last = start;
- while ((addr[0] & (CFG_FLASH_WORD_SIZE) 0x00800080) !=
- (CFG_FLASH_WORD_SIZE) 0x00800080) {
- DEBUGF("DQ7_2: start = 0x%08lx, now = 0x%08lx\n", start, now);
- if ((now = get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
- printf("Timeout\n");
- return -1;
- }
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- putc('.');
- last = now;
- }
- udelay(1000000); /* 1 sec */
- putc('.');
- counter++;
- if (counter > 5) {
- return -1;
- }
- DEBUGF("DQ7_2: now = 0x%08lx, last = 0x%08lx\n", now, last);
- }
- return 0;
-}
-
-static void wr_flash_cmd(ulong sector, ushort addr, CFG_FLASH_WORD_SIZE value)
-{
- int fw_size;
-
- fw_size = sizeof(value);
- switch (fw_size)
- {
- case 1:
- out8((ulong)(sector + addr), value);
- break;
- case 2:
- out16((ulong)(sector + (addr << 1)), value);
- break;
- default:
- printf("flash_erase: error incorrect chip programing size.\n");
- }
- return;
-}
-
-static int flash_erase_2(flash_info_t * info, int s_first, int s_last)
-{
- volatile CFG_FLASH_WORD_SIZE *addr = (CFG_FLASH_WORD_SIZE *) (info->start[0]);
- volatile CFG_FLASH_WORD_SIZE *addr2;
- int flag, prot, sect, l_sect, count = 0;
- int i;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf("- missing\n");
- } else {
- printf("- no sectors to erase\n");
- }
- return 1;
- }
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf("Can't erase unknown flash type - aborted\n");
- return 1;
- }
-
- prot = 0;
- for (sect = s_first; sect <= s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf("\n");
- }
-
- l_sect = -1;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- /* Start erase on unprotected sectors */
- for (sect = s_first, count = 0; sect <= s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- addr2 = (CFG_FLASH_WORD_SIZE *) (info->start[sect]);
-
- if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) {
- addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
- addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
- addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00800080;
- addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
- addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
- addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00500050; /* block erase */
- for (i = 0; i < 50; i++)
- udelay(1000); /* wait 1 ms */
- } else {
- /*
- * TODO: fix code
- */
- wr_flash_cmd((ulong)addr, 0, (CFG_FLASH_WORD_SIZE) 0x00F000F0);
- wr_flash_cmd((ulong)addr, CFG_FLASH_ADDR0, (CFG_FLASH_WORD_SIZE) 0x00AA00AA);
- wr_flash_cmd((ulong)addr, CFG_FLASH_ADDR1, (CFG_FLASH_WORD_SIZE) 0x00550055);
- wr_flash_cmd((ulong)addr, CFG_FLASH_ADDR0, (CFG_FLASH_WORD_SIZE) 0x00800080);
- wr_flash_cmd((ulong)addr, CFG_FLASH_ADDR0, (CFG_FLASH_WORD_SIZE) 0x00AA00AA);
- wr_flash_cmd((ulong)addr, CFG_FLASH_ADDR1, (CFG_FLASH_WORD_SIZE) 0x00550055);
- wr_flash_cmd((ulong)addr2, 0, (CFG_FLASH_WORD_SIZE) 0x00300030);
- udelay(2000000); /* 2 sec */
- wr_flash_cmd((ulong)addr, 0, (CFG_FLASH_WORD_SIZE) 0x00F000F0);
-
-#if 0
- addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
- addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
- addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00800080;
- addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
- addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
- addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00300030; /* sector erase */
-#endif
- }
- l_sect = sect;
- printf("..");
- printf("..");
- /*
- * Wait for each sector to complete, it's more
- * reliable. According to AMD Spec, you must
- * issue all erase commands within a specified
- * timeout. This has been seen to fail, especially
- * if printf()s are included (for debug)!!
- */
- wait_for_DQ7_2(info, sect);
- count++;
- }
- }
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* wait at least 80us - let's wait 1 ms */
- udelay(1000);
-
- /* reset to read mode */
- addr = (CFG_FLASH_WORD_SIZE *) info->start[0];
- addr[0] = (CFG_FLASH_WORD_SIZE) 0x00F000F0; /* reset bank */
-
- printf(" done\n");
-
- if (count > 0) {
- return 0;
- } else {
- return 1;
- }
-}
-
-static int write_word_2(flash_info_t * info, ulong dest, ulong data)
-{
- volatile CFG_FLASH_WORD_SIZE *addr2 = (CFG_FLASH_WORD_SIZE *) (info->start[0]);
- volatile CFG_FLASH_WORD_SIZE *dest2 = (CFG_FLASH_WORD_SIZE *) dest;
- volatile CFG_FLASH_WORD_SIZE *data2 = (CFG_FLASH_WORD_SIZE *) & data;
- ulong start;
- int i;
-
- /* Check if Flash is (sufficiently) erased */
- if ((*((vu_long *)dest) & data) != data) {
- return (2);
- }
-
- for (i = 0; i < 4 / sizeof(CFG_FLASH_WORD_SIZE); i++) {
- int flag;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
- addr2[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
- addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00A000A0;
-
- dest2[i] = data2[i];
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* data polling for D7 */
- start = get_timer(0);
- while ((dest2[i] & (CFG_FLASH_WORD_SIZE) 0x00800080) !=
- (data2[i] & (CFG_FLASH_WORD_SIZE) 0x00800080)) {
-
- if (get_timer(start) > CFG_FLASH_WRITE_TOUT) {
- return (1);
- }
- }
- }
-
- return (0);
-}
-#endif /* CFG_FLASH_2ND_16BIT_DEV */
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size(vu_long * addr, flash_info_t * info);
-static int write_word(flash_info_t * info, ulong dest, ulong data);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init(void)
-{
- unsigned long total_b = 0;
- unsigned long size_b[CFG_MAX_FLASH_BANKS];
- unsigned short index = 0;
- int i;
-
- index = 0;
-
- DEBUGF("\n");
- DEBUGF("FLASH: Index: %d\n", index);
-
- /* Init: no FLASHes known */
- for (i = 0; i < CFG_MAX_FLASH_BANKS; ++i) {
- flash_info[i].flash_id = FLASH_UNKNOWN;
- flash_info[i].sector_count = -1;
- flash_info[i].size = 0;
-
- /* check whether the address is 0 */
- if (flash_addr_table[index][i] == 0) {
- continue;
- }
-
- /* call flash_get_size() to initialize sector address */
- size_b[i] = flash_get_size((vu_long *) flash_addr_table[index][i],
- &flash_info[i]);
- flash_info[i].size = size_b[i];
- if (flash_info[i].flash_id == FLASH_UNKNOWN) {
- printf("## Unknown FLASH on Bank %d - Size = 0x%08lx = %ld MB\n",
- i, size_b[i], size_b[i] << 20);
- flash_info[i].sector_count = -1;
- flash_info[i].size = 0;
- }
-
- /* Monitor protection ON by default */
- (void)flash_protect(FLAG_PROTECT_SET, CFG_MONITOR_BASE,
- CFG_MONITOR_BASE + CFG_MONITOR_LEN - 1,
- &flash_info[i]);
-#if defined(CFG_ENV_IS_IN_FLASH)
- (void)flash_protect(FLAG_PROTECT_SET, CFG_ENV_ADDR,
- CFG_ENV_ADDR + CFG_ENV_SECT_SIZE - 1,
- &flash_info[i]);
-#if defined(CFG_ENV_IS_IN_FLASH) && defined(CFG_ENV_ADDR_REDUND)
- (void)flash_protect(FLAG_PROTECT_SET, CFG_ENV_ADDR_REDUND,
- CFG_ENV_ADDR_REDUND + CFG_ENV_SECT_SIZE - 1,
- &flash_info[i]);
-#endif
-#endif
-
- total_b += flash_info[i].size;
- }
-
- return total_b;
-}
diff --git a/board/amcc/acadia/memory.c b/board/amcc/acadia/memory.c
index a1b0155..5375d36 100644
--- a/board/amcc/acadia/memory.c
+++ b/board/amcc/acadia/memory.c
@@ -21,529 +21,80 @@
* MA 02111-1307 USA
*/
+/* define DEBUG for debugging output (obviously ;-)) */
+#if 0
+#define DEBUG
+#endif
+
#include <common.h>
#include <asm/processor.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
-#define CRAM_BANK0_BASE 0x0
-#define CRAM_DIDR 0x00100000
-#define MICRON_MT45W8MW16BGX_CRAM_ID 0x1b431b43
-#define MICRON_MT45W8MW16BGX_CRAM_ID2 0x13431343
-#define MICRON_DIDR_VENDOR_ID 0x00030003 /* 00011b */
-#define CRAM_DIDR_VENDOR_ID_MASK 0x001f001f /* DIDR[4:0] */
-#define CRAM_DEVID_NOT_SUPPORTED 0x00000000
-
-#define PSRAM_PASS 0x50415353 /* "PASS" */
-#define PSRAM_FAIL 0x4641494C /* "FAIL" */
-
-static u32 is_cram_inited(void);
-static u32 is_cram(void);
-static long int cram_init(u32);
-static void cram_bcr_write(u32);
-void udelay (unsigned long);
-
+/*
+ * sdram_init - Dummy implementation for start.S, spd_sdram used on this board!
+ */
void sdram_init(void)
{
- volatile unsigned long spr_reg;
-
- /*
- * If CRAM not initialized or CRAM looks initialized because this
- * is after a warm reboot then set SPRG7 to indicate CRAM needs
- * initialization. Note that CRAM is initialized by the SPI and
- * NAND preloader.
- */
- spr_reg = (volatile unsigned long) mfspr(SPRG6);
- if ((is_cram_inited() != 1) || (spr_reg != LOAK_SPL)) {
- mtspr(SPRG7, LOAK_NONE); /* "NONE" */
- }
-#if 1
- /*
- * When running the NAND SPL, the normal EBC configuration is not
- * done, so We need to enable EPLD access on EBC_CS_2 and the memory
- * on EBC_CS_3
- */
-
- /* Enable CPLD - Needed for PSRAM Access */
-
-
- /* Init SDRAM by setting EBC Bank 3 for PSRAM */
- mtebc(pb1ap, CFG_EBC_PB1AP);
- mtebc(pb1cr, CFG_EBC_PB1CR);
-
- mtebc(pb2ap, CFG_EBC_PB2AP);
- mtebc(pb2cr, CFG_EBC_PB2CR);
-
- /* pre-boot loader code: we are in OCM */
- mtspr(SPRG6, LOAK_SPL); /* "SPL " */
- mtspr(SPRG7, LOAK_OCM); /* "OCM " */
-#endif
return;
}
static void cram_bcr_write(u32 wr_val)
{
- u32 tmp_reg;
- u32 val;
- volatile u32 gpio_reg;
+ wr_val <<= 2;
- /* # Program CRAM write */
+ /* set CRAM_CRE to 1 */
+ gpio_write_bit(CFG_GPIO_CRAM_CRE, 1);
- /*
- * set CRAM_CRE = 0x1
- * set wr_val = wr_val << 2
- */
- gpio_reg = in32(GPIO1_OR);
- out32(GPIO1_OR, gpio_reg | 0x00000400);
- wr_val = wr_val << 2;
- /* wr_val = 0x1c048; */
+ /* Write BCR to CRAM on CS1 */
+ out32(wr_val + 0x00200000, 0);
+ debug("CRAM VAL: %08x for CS1 ", wr_val + 0x00200000);
- /*
- * # stop PLL clock before programming CRAM
- * set EPLD0_MUX_CTL.OESPR3 = 1
- * delay 2
- */
+ /* Write BCR to CRAM on CS2 */
+ out32(wr_val + 0x02200000, 0);
+ debug("CRAM VAL: %08x for CS2\n", wr_val + 0x02200000);
- /*
- * # CS1
- * read 0x00200000
- * #shift 2 bit left before write
- * set val = wr_val + 0x00200000
- * write dmem val 0
- * read 0x00200000 val
- * print val/8x
- */
- tmp_reg = in32(0x00200000);
- val = wr_val + 0x00200000;
- /* val = 0x0021c048; */
- out32(val, 0x0000);
- udelay(100000);
- val = in32(0x00200000);
+ sync();
+ eieio();
- debug("CRAM VAL: %x for CS1 ", val);
+ /* set CRAM_CRE back to 0 (normal operation) */
+ gpio_write_bit(CFG_GPIO_CRAM_CRE, 0);
- /*
- * # CS2
- * read 0x02200000
- * #shift 2 bit left before write
- * set val = wr_val + 0x02200000
- * write dmem val 0
- * read 0x02200000 val
- * print val/8x
- */
- tmp_reg = in32(0x02200000);
- val = wr_val + 0x02200000;
- /* val = 0x0221c048; */
- out32(val, 0x0000);
- udelay(100000);
- val = in32(0x02200000);
-
- debug("CRAM VAL: %x for CS2 ", val);
-
- /*
- * # Start PLL clock before programming CRAM
- * set EPLD0_MUX_CTL.OESPR3 = 0
- */
-
- /*
- * set CRAMCR = 0x1
- */
- gpio_reg = in32(GPIO1_OR);
- out32(GPIO1_OR, gpio_reg | 0x00000400);
-
- /*
- * # read CRAM config BCR ( bit19:18 = 10b )
- * #read 0x00200000
- * # 1001_1001_0001_1111 ( 991f ) =>
- * #10_0110_0100_0111_1100 => 2647c => 0022647c
- * #0011_0010_0011_1110 (323e)
- * #
- */
-
- /*
- * set EPLD0_MUX_CTL.CRAMCR = 0x0
- */
- gpio_reg = in32(GPIO1_OR);
- out32(GPIO1_OR, gpio_reg & 0xFFFFFBFF);
return;
}
-static u32 is_cram_inited()
-{
- volatile unsigned long spr_reg;
-
- /*
- * If CRAM is initialized already, then don't reinitialize it again.
- * In the case of NAND boot and SPI boot, CRAM will already be
- * initialized by the pre-loader
- */
- spr_reg = (volatile unsigned long) mfspr(SPRG7);
- if (spr_reg == LOAK_CRAM) {
- return 1;
- } else {
- return 0;
- }
-}
-
-/******
- * return 0 if not CRAM
- * return 1 if CRAM and it's already inited by preloader
- * else return cram_id (CRAM Device Identification Register)
- ******/
-static u32 is_cram(void)
-{
- u32 gpio_TCR, gpio_OSRL, gpio_OR, gpio_ISR1L;
- volatile u32 gpio_reg;
- volatile u32 cram_id = 0;
-
- if (is_cram_inited() == 1) {
- /* this is CRAM and it is already inited (by preloader) */
- cram_id = 1;
- } else {
- /*
- * # CRAM CLOCK
- * set GPIO0_TCR.G8 = 1
- * set GPIO0_OSRL.G8 = 0
- * set GPIO0_OR.G8 = 0
- */
- gpio_reg = in32(GPIO0_TCR);
- gpio_TCR = gpio_reg;
- out32(GPIO0_TCR, gpio_reg | 0x00800000);
- gpio_reg = in32(GPIO0_OSRL);
- gpio_OSRL = gpio_reg;
- out32(GPIO0_OSRL, gpio_reg & 0xffffbfff);
- gpio_reg = in32(GPIO0_OR);
- gpio_OR = gpio_reg;
- out32(GPIO0_OR, gpio_reg & 0xff7fffff);
-
- /*
- * # CRAM Addreaa Valid
- * set GPIO0_TCR.G10 = 1
- * set GPIO0_OSRL.G10 = 0
- * set GPIO0_OR.G10 = 0
- */
- gpio_reg = in32(GPIO0_TCR);
- out32(GPIO0_TCR, gpio_reg | 0x00200000);
- gpio_reg = in32(GPIO0_OSRL);
- out32(GPIO0_OSRL, gpio_reg & 0xfffffbff);
- gpio_reg = in32(GPIO0_OR);
- out32(GPIO0_OR, gpio_reg & 0xffdfffff);
-
- /*
- * # config input (EBC_WAIT)
- * set GPIO0_ISR1L.G9 = 1
- * set GPIO0_TCR.G9 = 0
- */
- gpio_reg = in32(GPIO0_ISR1L);
- gpio_ISR1L = gpio_reg;
- out32(GPIO0_ISR1L, gpio_reg | 0x00001000);
- gpio_reg = in32(GPIO0_TCR);
- out32(GPIO0_TCR, gpio_reg & 0xffbfffff);
-
- /*
- * Enable CRE to read Registers
- * set GPIO0_TCR.21 = 1
- * set GPIO1_OR.21 = 1
- */
- gpio_reg = in32(GPIO1_TCR);
- out32(GPIO1_TCR, gpio_reg | 0x00000400);
-
- gpio_reg = in32(GPIO1_OR);
- out32(GPIO1_OR, gpio_reg | 0x00000400);
-
- /* Read Version ID */
- cram_id = (volatile u32) in32(CRAM_BANK0_BASE+CRAM_DIDR);
- udelay(100000);
-
- asm volatile(" sync");
- asm volatile(" eieio");
-
- debug("Cram ID: %X ", cram_id);
-
- switch (cram_id) {
- case MICRON_MT45W8MW16BGX_CRAM_ID:
- case MICRON_MT45W8MW16BGX_CRAM_ID2:
- /* supported CRAM vendor/part */
- break;
- case CRAM_DEVID_NOT_SUPPORTED:
- default:
- /* check for DIDR Vendor ID of Micron */
- if ((cram_id & CRAM_DIDR_VENDOR_ID_MASK) ==
- MICRON_DIDR_VENDOR_ID)
- {
- /* supported CRAM vendor */
- break;
- }
- /* this is not CRAM or not supported CRAM vendor/part */
- cram_id = 0;
- /*
- * reset the GPIO registers to the values that were
- * there before this routine
- */
- out32(GPIO0_TCR, gpio_TCR);
- out32(GPIO0_OSRL, gpio_OSRL);
- out32(GPIO0_OR, gpio_OR);
- out32(GPIO0_ISR1L, gpio_ISR1L);
- break;
- }
- }
-
- return cram_id;
-}
-
-static long int cram_init(u32 already_inited)
-{
- volatile u32 tmp_reg;
- u32 cram_wr_val;
-
- if (already_inited == 0) return 0;
-
- /*
- * If CRAM is initialized already, then don't reinitialize it again.
- * In the case of NAND boot and SPI boot, CRAM will already be
- * initialized by the pre-loader
- */
- if (already_inited != 1) {
- /*
- * #o CRAM Card
- * # - CRAMCRE @reg16 = 1; for CRAM to use
- * # - CRAMCRE @reg16 = 0; for CRAM to program
- *
- * # enable CRAM SEL, move from setEPLD.cmd
- * set EPLD0_MUX_CTL.OECRAM = 0
- * set EPLD0_MUX_CTL.CRAMCR = 1
- * set EPLD0_ETHRSTBOOT.SLCRAM = 0
- * #end
- */
-
- /*
- * #1. EBC need to program READY, CLK, ADV for ASync mode
- * # config output
- */
-
- /*
- * # CRAM CLOCK
- * set GPIO0_TCR.G8 = 1
- * set GPIO0_OSRL.G8 = 0
- * set GPIO0_OR.G8 = 0
- */
- tmp_reg = in32(GPIO0_TCR);
- out32(GPIO0_TCR, tmp_reg | 0x00800000);
- tmp_reg = in32(GPIO0_OSRL);
- out32(GPIO0_OSRL, tmp_reg & 0xffffbfff);
- tmp_reg = in32(GPIO0_OR);
- out32(GPIO0_OR, tmp_reg & 0xff7fffff);
-
- /*
- * # CRAM Addreaa Valid
- * set GPIO0_TCR.G10 = 1
- * set GPIO0_OSRL.G10 = 0
- * set GPIO0_OR.G10 = 0
- */
- tmp_reg = in32(GPIO0_TCR);
- out32(GPIO0_TCR, tmp_reg | 0x00200000);
- tmp_reg = in32(GPIO0_OSRL);
- out32(GPIO0_OSRL, tmp_reg & 0xfffffbff);
- tmp_reg = in32(GPIO0_OR);
- out32(GPIO0_OR, tmp_reg & 0xffdfffff);
-
- /*
- * # config input (EBC_WAIT)
- * set GPIO0_ISR1L.G9 = 1
- * set GPIO0_TCR.G9 = 0
- */
- tmp_reg = in32(GPIO0_ISR1L);
- out32(GPIO0_ISR1L, tmp_reg | 0x00001000);
- tmp_reg = in32(GPIO0_TCR);
- out32(GPIO0_TCR, tmp_reg & 0xffbfffff);
-
- /*
- * # config CS4 from GPIO
- * set GPIO0_TCR.G0 = 1
- * set GPIO0_OSRL.G0 = 1
- */
- tmp_reg = in32(GPIO0_TCR);
- out32(GPIO0_TCR, tmp_reg | 0x80000000);
- tmp_reg = in32(GPIO0_OSRL);
- out32(GPIO0_OSRL, tmp_reg | 0x40000000);
-
- /*
- * #2. EBC in Async mode
- * # set EBC0_PB1AP = 0x078f0ec0
- * set EBC0_PB1AP = 0x078f1ec0
- * set EBC0_PB2AP = 0x078f1ec0
- */
- mtebc(pb1ap, 0x078F1EC0);
- mtebc(pb2ap, 0x078F1EC0);
-
- /*
- * #set EBC0_PB1CR = 0x000bc000
- * #enable CS2 for CRAM
- * set EBC0_PB2CR = 0x020bc000
- */
- mtebc(pb1cr, 0x000BC000);
- mtebc(pb2cr, 0x020BC000);
-
- /*
- * #3. set CRAM in Sync mode
- * #exec cm_bcr_write.cmd { 0x701f }
- * #3. set CRAM in Sync mode (full drv strength)
- * exec cm_bcr_write.cmd { 0x701F }
- */
- cram_wr_val = 0x7012; /* CRAM burst setting */
- cram_bcr_write(cram_wr_val);
-
- /*
- * #4. EBC in Sync mode
- * #set EBC0_PB1AP = 0x9f800fc0
- * #set EBC0_PB1AP = 0x900001c0
- * set EBC0_PB2AP = 0x9C0201c0
- * set EBC0_PB2AP = 0x9C0201c0
- */
- mtebc(pb1ap, 0x9C0201C0);
- mtebc(pb2ap, 0x9C0201C0);
-
- /*
- * #5. EBC need to program READY, CLK, ADV for Sync mode
- * # config output
- * set GPIO0_TCR.G8 = 1
- * set GPIO0_OSRL.G8 = 1
- * set GPIO0_TCR.G10 = 1
- * set GPIO0_OSRL.G10 = 1
- */
- tmp_reg = in32(GPIO0_TCR);
- out32(GPIO0_TCR, tmp_reg | 0x00800000);
- tmp_reg = in32(GPIO0_OSRL);
- out32(GPIO0_OSRL, tmp_reg | 0x00004000);
- tmp_reg = in32(GPIO0_TCR);
- out32(GPIO0_TCR, tmp_reg | 0x00200000);
- tmp_reg = in32(GPIO0_OSRL);
- out32(GPIO0_OSRL, tmp_reg | 0x00000400);
-
- /*
- * # config input
- * set GPIO0_ISR1L.G9 = 1
- * set GPIO0_TCR.G9 = 0
- */
- tmp_reg = in32(GPIO0_ISR1L);
- out32(GPIO0_ISR1L, tmp_reg | 0x00001000);
- tmp_reg = in32(GPIO0_TCR);
- out32(GPIO0_TCR, tmp_reg & 0xffbfffff);
-
- /*
- * # config EBC to use RDY
- * set SDR0_ULTRA0.EBCREN = 1
- */
- mfsdr(sdrultra0, tmp_reg);
- mtsdr(sdrultra0, tmp_reg | 0x04000000);
-
- /*
- * set EPLD0_MUX_CTL.OESPR3 = 0
- */
- mtspr(SPRG7, LOAK_CRAM); /* "CRAM" */
- } /* if (already_inited != 1) */
-
- return (64 * 1024 * 1024);
-}
-
-/******
- * return 0 if not PSRAM
- * return 1 if is PSRAM
- ******/
-static int is_psram(u32 addr)
-{
- u32 test_pattern = 0xdeadbeef;
- volatile u32 readback;
-
- if (addr == CFG_SDRAM_BASE) {
- /* This is to temp enable OE for PSRAM */
- out16(EPLD_BASE+EPLD_MUXOE, 0x7f0f);
- udelay(10000);
- }
-
- out32(addr, test_pattern);
- asm volatile(" sync");
- asm volatile(" eieio");
-
- readback = (volatile u32) in32(addr);
- asm volatile(" sync");
- asm volatile(" eieio");
- if (readback == test_pattern) {
- return 1;
- } else {
- return 0;
- }
-}
-
-static long int psram_init(void)
+long int initdram(int board_type)
{
- u32 readback;
- long psramsize = 0;
- int i;
-
- /* This is to temp enable OE for PSRAM */
- out16(EPLD_BASE+EPLD_MUXOE, 0x7f0f);
- udelay(10000);
+ u32 val;
- /*
- * PSRAM bank 1: read then write to address 0x00000000
- */
- for (i = 0; i < 100; i++) {
- if (is_psram(CFG_SDRAM_BASE + (i*256)) == 1) {
- readback = PSRAM_PASS;
- } else {
- readback = PSRAM_FAIL;
- break;
- }
- }
- if (readback == PSRAM_PASS) {
- debug("psram_init(bank0): pass\n");
- psramsize = (16 * 1024 * 1024);
- } else {
- debug("psram_init(bank0): fail\n");
- return 0;
- }
+ /* 1. EBC need to program READY, CLK, ADV for ASync mode */
+ gpio_config(CFG_GPIO_CRAM_CLK, GPIO_OUT, GPIO_SEL, GPIO_OUT_0);
+ gpio_config(CFG_GPIO_CRAM_ADV, GPIO_OUT, GPIO_SEL, GPIO_OUT_0);
+ gpio_config(CFG_GPIO_CRAM_CRE, GPIO_OUT, GPIO_SEL, GPIO_OUT_0);
+ gpio_config(CFG_GPIO_CRAM_WAIT, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG);
-#if 0
- /*
- * PSRAM bank 1: read then write to address 0x01000000
- */
- for (i = 0; i < 100; i++) {
- if (is_psram((1 << 24) + (i*256)) == 1) {
- readback = PSRAM_PASS;
- } else {
- readback = PSRAM_FAIL;
- break;
- }
- }
- if (readback == PSRAM_PASS) {
- debug("psram_init(bank1): pass\n");
- psramsize = psramsize + (16 * 1024 * 1024);
- }
-#endif
+ /* 2. EBC in Async mode */
+ mtebc(pb1ap, 0x078F1EC0);
+ mtebc(pb2ap, 0x078F1EC0);
+ mtebc(pb1cr, 0x000BC000);
+ mtebc(pb2cr, 0x020BC000);
- mtspr(SPRG7, LOAK_PSRAM); /* "PSRA" - PSRAM */
+ /* 3. Set CRAM in Sync mode */
+ cram_bcr_write(0x7012); /* CRAM burst setting */
- return psramsize;
-}
+ /* 4. EBC in Sync mode */
+ mtebc(pb1ap, 0x9C0201C0);
+ mtebc(pb2ap, 0x9C0201C0);
-long int initdram(int board_type)
-{
- long int sram_size;
- u32 cram_inited;
+ /* Set GPIO pins back to alternate function */
+ gpio_config(CFG_GPIO_CRAM_CLK, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG);
+ gpio_config(CFG_GPIO_CRAM_ADV, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG);
- /* Determine Attached Memory Expansion Card*/
- cram_inited = is_cram();
- if (cram_inited != 0) { /* CRAM */
- debug("CRAM Expansion Card attached\n");
- sram_size = cram_init(cram_inited);
- } else if (is_psram(CFG_SDRAM_BASE+4) == 1) { /* PSRAM */
- debug("PSRAM Expansion Card attached\n");
- sram_size = psram_init();
- } else { /* no SRAM */
- debug("No Memory Card Attached!!\n");
- sram_size = 0;
- }
+ /* Config EBC to use RDY */
+ mfsdr(sdrultra0, val);
+ mtsdr(sdrultra0, val | 0x04000000);
- return sram_size;
+ return (CFG_MBYTES_RAM << 20);
}
int testdram(void)
diff --git a/board/amcc/acadia/u-boot.lds b/board/amcc/acadia/u-boot.lds
index be03092..b08c999 100644
--- a/board/amcc/acadia/u-boot.lds
+++ b/board/amcc/acadia/u-boot.lds
@@ -62,19 +62,6 @@
/* the sector layout of our flash chips! XXX FIXME XXX */
cpu/ppc4xx/start.o (.text)
- cpu/ppc4xx/kgdb.o (.text)
- cpu/ppc4xx/traps.o (.text)
- cpu/ppc4xx/interrupts.o (.text)
- cpu/ppc4xx/serial.o (.text)
- cpu/ppc4xx/cpu_init.o (.text)
- cpu/ppc4xx/speed.o (.text)
- common/dlmalloc.o (.text)
- lib_generic/crc32.o (.text)
- lib_ppc/extable.o (.text)
- lib_generic/zlib.o (.text)
-
-/* . = env_offset;*/
-/* common/environment.o(.text)*/
*(.text)
*(.fixup)
diff --git a/board/amcc/bamboo/bamboo.c b/board/amcc/bamboo/bamboo.c
index c93ba6e..b5bb145 100644
--- a/board/amcc/bamboo/bamboo.c
+++ b/board/amcc/bamboo/bamboo.c
@@ -23,6 +23,7 @@
#include <common.h>
#include <asm/processor.h>
+#include <asm/gpio.h>
#include <spd_sdram.h>
#include <ppc440.h>
#include "bamboo.h"
diff --git a/board/amcc/bamboo/bamboo.h b/board/amcc/bamboo/bamboo.h
index 1ce6366..4474862 100644
--- a/board/amcc/bamboo/bamboo.h
+++ b/board/amcc/bamboo/bamboo.h
@@ -264,19 +264,9 @@
#define TRUE 1
#define FALSE 0
-#define GPIO_GROUP_MAX 2
-#define GPIO_MAX 32
-#define GPIO_ALT1_SEL 0x40000000 /* GPIO_OUT value put in GPIO_TSx for the GPIO nb 0 */
-#define GPIO_ALT2_SEL 0x80000000 /* GPIO_OUT value put in GPIO_TSx for the GPIO nb 1 */
-#define GPIO_ALT3_SEL 0xC0000000 /* GPIO_OUT value put in GPIO_TSx for the GPIO nb 2 */
-#define GPIO_MASK 0xC0000000 /* GPIO_MASK */
-#define GPIO_IN_SEL 0x40000000 /* GPIO_IN value put in GPIO_ISx for the GPIO nb 0 */
- /* For the other GPIO number, you must shift */
-
#define GPIO0 0
#define GPIO1 1
-
/*#define MAX_SELECTION_NB CORE_NB */
#define MAX_CORE_SELECT_NB 22
diff --git a/board/amcc/katmai/cmd_katmai.c b/board/amcc/katmai/cmd_katmai.c
index 684f6a5..439be4f 100644
--- a/board/amcc/katmai/cmd_katmai.c
+++ b/board/amcc/katmai/cmd_katmai.c
@@ -27,6 +27,9 @@
#include <i2c.h>
#include <asm/byteorder.h>
+#define CONFIG_STRESS /* enable 667 MHz CPU freq selection */
+#define DEBUG
+
static int do_bootstrap(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
{
uchar chip;
@@ -49,55 +52,28 @@
else
chip = IIC0_ALT_BOOTPROM_ADDR;
- do {
- printf("enter sys clock frequency 33 or 66 Mhz or quit to abort\n");
- nbytes = readline (" ? ");
-
- if (strcmp(console_buffer, "quit") == 0)
- return 0;
-
- if ((strcmp(console_buffer, "33") != 0) &
- (strcmp(console_buffer, "66") != 0))
- nbytes=0;
-
- strcpy(sysClock, console_buffer);
-
- } while (nbytes == 0);
+ /* on Katmai SysClk is always 33MHz */
+ strcpy(sysClock, "33");
do {
- if (strcmp(sysClock, "66") == 0) {
- printf("enter cpu clock frequency 400, 533 Mhz or quit to abort\n");
- } else {
#ifdef CONFIG_STRESS
- printf("enter cpu clock frequency 400, 500, 533, 667 Mhz or quit to abort\n");
+ printf("enter cpu clock frequency 400, 500, 533, 667 Mhz or quit to abort\n");
#else
- printf("enter cpu clock frequency 400, 500, 533 Mhz or quit to abort\n");
+ printf("enter cpu clock frequency 400, 500, 533 Mhz or quit to abort\n");
#endif
- }
nbytes = readline (" ? ");
if (strcmp(console_buffer, "quit") == 0)
return 0;
- if (strcmp(sysClock, "66") == 0) {
- if ((strcmp(console_buffer, "400") != 0) &
- (strcmp(console_buffer, "533") != 0)
-#ifdef CONFIG_STRESS
- & (strcmp(console_buffer, "667") != 0)
-#endif
- ) {
- nbytes = 0;
- }
- } else {
- if ((strcmp(console_buffer, "400") != 0) &
- (strcmp(console_buffer, "500") != 0) &
- (strcmp(console_buffer, "533") != 0)
+ if ((strcmp(console_buffer, "400") != 0) &&
+ (strcmp(console_buffer, "500") != 0) &&
+ (strcmp(console_buffer, "533") != 0)
#ifdef CONFIG_STRESS
- & (strcmp(console_buffer, "667") != 0)
+ && (strcmp(console_buffer, "667") != 0)
#endif
- ) {
- nbytes = 0;
- }
+ ) {
+ nbytes = 0;
}
strcpy(cpuClock, console_buffer);
@@ -124,13 +100,13 @@
return 0;
if (strcmp(cpuClock, "400") == 0) {
- if ((strcmp(console_buffer, "100") != 0) &
+ if ((strcmp(console_buffer, "100") != 0) &&
(strcmp(console_buffer, "133") != 0))
nbytes = 0;
}
#ifdef CONFIG_STRESS
if (strcmp(cpuClock, "667") == 0) {
- if ((strcmp(console_buffer, "133") != 0) &
+ if ((strcmp(console_buffer, "133") != 0) &&
(strcmp(console_buffer, "166") != 0))
nbytes = 0;
}
@@ -147,9 +123,9 @@
if (strcmp(console_buffer, "quit") == 0)
return 0;
- if ((strcmp(console_buffer, "33") != 0) &
- (strcmp(console_buffer, "66") != 0) &
- (strcmp(console_buffer, "100") != 0) &
+ if ((strcmp(console_buffer, "33") != 0) &&
+ (strcmp(console_buffer, "66") != 0) &&
+ (strcmp(console_buffer, "100") != 0) &&
(strcmp(console_buffer, "133") != 0)) {
nbytes = 0;
}
@@ -176,11 +152,11 @@
} while (nbytes == 0);
if (strcmp(sysClock, "33") == 0) {
- if ((strcmp(cpuClock, "400") == 0) &
+ if ((strcmp(cpuClock, "400") == 0) &&
(strcmp(plbClock, "100") == 0))
data = 0x8678c206;
- if ((strcmp(cpuClock, "400") == 0) &
+ if ((strcmp(cpuClock, "400") == 0) &&
(strcmp(plbClock, "133") == 0))
data = 0x8678c2c6;
@@ -189,42 +165,16 @@
if ((strcmp(cpuClock, "533") == 0))
data = 0x87790252;
-
#ifdef CONFIG_STRESS
- if ((strcmp(cpuClock, "667") == 0) &
+ if ((strcmp(cpuClock, "667") == 0) &&
(strcmp(plbClock, "133") == 0))
data = 0x87794256;
- if ((strcmp(cpuClock, "667") == 0) &
+ if ((strcmp(cpuClock, "667") == 0) &&
(strcmp(plbClock, "166") == 0))
data = 0x87794206;
-
-#endif
- }
- if (strcmp(sysClock, "66") == 0) {
- if ((strcmp(cpuClock, "400") == 0) &
- (strcmp(plbClock, "100") == 0))
- data = 0x84706206;
-
- if ((strcmp(cpuClock, "400") == 0) &
- (strcmp(plbClock, "133") == 0))
- data = 0x847062c6;
-
- if ((strcmp(cpuClock, "533") == 0))
- data = 0x85708206;
-
-#ifdef CONFIG_STRESS
- if ((strcmp(cpuClock, "667") == 0) &
- (strcmp(plbClock, "133") == 0))
- data = 0x8570a256;
-
- if ((strcmp(cpuClock, "667") == 0) &
- (strcmp(plbClock, "166") == 0))
- data = 0x8570a206;
-
#endif
}
-
#ifdef DEBUG
printf(" pin strap0 to write in i2c = %x\n", data);
#endif /* DEBUG */
@@ -233,19 +183,20 @@
printf("Error writing strap0 in %s\n", argv[2]);
if (strcmp(pcixClock, "33") == 0)
- data = 0x00000701;
+ data = 0x000007E1;
if (strcmp(pcixClock, "66") == 0)
- data = 0x00000601;
+ data = 0x000006E1;
if (strcmp(pcixClock, "100") == 0)
- data = 0x00000501;
+ data = 0x000005E1;
if (strcmp(pcixClock, "133") == 0)
- data = 0x00000401;
+ data = 0x000004E1;
if (strcmp(plbClock, "166") == 0)
- data |= 0x05950000;
+/* data |= 0x05950000; */ /* this set's DDR2 clock == PLB clock */
+ data |= 0x05A50000; /* this set's DDR2 clock == 2 * PLB clock */
else
data |= 0x05A50000;
diff --git a/board/amcc/katmai/init.S b/board/amcc/katmai/init.S
index 6b024ee..5202ae6 100644
--- a/board/amcc/katmai/init.S
+++ b/board/amcc/katmai/init.S
@@ -103,7 +103,7 @@
tlbentry(CFG_PERIPHERAL_BASE, SZ_4K, 0xF0000000, 4, AC_R|AC_W|SA_G|SA_I)
- tlbentry(CFG_ACE_BASE, SZ_1K, 0xE0000000, 4,AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_ACE_BASE, SZ_1K, CFG_ACE_BASE, 4,AC_R|AC_W|SA_G|SA_I)
tlbentry(CFG_PCI_BASE, SZ_256M, 0x00000000, 0xC, AC_R|AC_W|SA_G|SA_I)
tlbentry(CFG_PCI_MEMBASE, SZ_256M, 0x10000000, 0xC, AC_R|AC_W|SA_G|SA_I)
diff --git a/board/amcc/katmai/katmai.c b/board/amcc/katmai/katmai.c
index fbf1a98..286bdc1 100644
--- a/board/amcc/katmai/katmai.c
+++ b/board/amcc/katmai/katmai.c
@@ -27,6 +27,7 @@
#include <asm/processor.h>
#include <i2c.h>
#include <asm-ppc/io.h>
+#include <asm-ppc/gpio.h>
#include "../cpu/ppc4xx/440spe_pcie.h"
diff --git a/board/amcc/sequoia/sequoia.c b/board/amcc/sequoia/sequoia.c
index daaffe0..930fa71 100644
--- a/board/amcc/sequoia/sequoia.c
+++ b/board/amcc/sequoia/sequoia.c
@@ -363,8 +363,8 @@
printf("Board: Rainier - AMCC PPC440GRx Evaluation Board");
#endif
- rev = *(u8 *)(CFG_CPLD + 0);
- val = *(u8 *)(CFG_CPLD + 5) & 0x01;
+ rev = *(u8 *)(CFG_BCSR_BASE + 0);
+ val = *(u8 *)(CFG_BCSR_BASE + 5) & 0x01;
printf(", Rev. %X, PCI=%d MHz", rev, val ? 66 : 33);
if (s != NULL) {
diff --git a/board/atmel/atstk1000/Makefile b/board/atmel/atstk1000/Makefile
index 155d46a..8a15713 100644
--- a/board/atmel/atstk1000/Makefile
+++ b/board/atmel/atstk1000/Makefile
@@ -26,7 +26,7 @@
LIB := $(obj)lib$(BOARD).a
-COBJS := $(BOARD).o flash.o
+COBJS := $(BOARD).o flash.o eth.o
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
diff --git a/board/atmel/atstk1000/atstk1000.c b/board/atmel/atstk1000/atstk1000.c
index 4d737d2..6618963 100644
--- a/board/atmel/atstk1000/atstk1000.c
+++ b/board/atmel/atstk1000/atstk1000.c
@@ -23,6 +23,8 @@
#include <asm/io.h>
#include <asm/sdram.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/hmatrix2.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -40,9 +42,27 @@
.txsr = 5,
};
-void board_init_memories(void)
+int board_early_init_f(void)
+{
+ /* Set the SDRAM_ENABLE bit in the HEBI SFR */
+ hmatrix2_writel(SFR4, 1 << 1);
+
+ gpio_enable_ebi();
+ gpio_enable_usart1();
+#if defined(CONFIG_MACB)
+ gpio_enable_macb0();
+ gpio_enable_macb1();
+#endif
+#if defined(CONFIG_MMC)
+ gpio_enable_mmci();
+#endif
+
+ return 0;
+}
+
+long int initdram(int board_type)
{
- gd->sdram_size = sdram_init(&sdram);
+ return sdram_init(&sdram);
}
void board_init_info(void)
diff --git a/cpu/at32ap/at32ap7000/hebi.c b/board/atmel/atstk1000/eth.c
similarity index 66%
rename from cpu/at32ap/at32ap7000/hebi.c
rename to board/atmel/atstk1000/eth.c
index 3b32adf..3a7916e 100644
--- a/cpu/at32ap/at32ap7000/hebi.c
+++ b/board/atmel/atstk1000/eth.c
@@ -1,5 +1,7 @@
/*
- * Copyright (C) 2006 Atmel Corporation
+ * Copyright (C) 2005-2006 Atmel Corporation
+ *
+ * Ethernet initialization for the ATSTK1000 starterkit
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -21,18 +23,16 @@
*/
#include <common.h>
-#include <asm/io.h>
-
-#include <asm/arch/hmatrix2.h>
#include <asm/arch/memory-map.h>
-#include <asm/arch/platform.h>
-void cpu_enable_sdram(void)
-{
- const struct device *hmatrix;
+extern int macb_eth_initialize(int id, void *regs, unsigned int phy_addr);
- hmatrix = get_device(DEVICE_HMATRIX);
+#if defined(CONFIG_MACB) && (CONFIG_COMMANDS & CFG_CMD_NET)
+void atstk1000_eth_initialize(bd_t *bi)
+{
+ int id = 0;
- /* Set the SDRAM_ENABLE bit in the HEBI SFR */
- hmatrix2_writel(hmatrix, SFR4, 1 << 1);
+ macb_eth_initialize(id++, (void *)MACB0_BASE, bi->bi_phy_id[0]);
+ macb_eth_initialize(id++, (void *)MACB1_BASE, bi->bi_phy_id[1]);
}
+#endif
diff --git a/board/atmel/atstk1000/flash.c b/board/atmel/atstk1000/flash.c
index 3aebf66..958f4dc 100644
--- a/board/atmel/atstk1000/flash.c
+++ b/board/atmel/atstk1000/flash.c
@@ -57,7 +57,7 @@
gd->bd->bi_flashstart = CFG_FLASH_BASE;
gd->bd->bi_flashsize = CFG_FLASH_SIZE;
- gd->bd->bi_flashoffset = __edata_lma - _text;
+ gd->bd->bi_flashoffset = _edata - _text;
flash_info[0].size = CFG_FLASH_SIZE;
flash_info[0].sector_count = 135;
diff --git a/board/atmel/atstk1000/u-boot.lds b/board/atmel/atstk1000/u-boot.lds
index ef89ea4..34e347a 100644
--- a/board/atmel/atstk1000/u-boot.lds
+++ b/board/atmel/atstk1000/u-boot.lds
@@ -40,35 +40,38 @@
}
. = ALIGN(32);
__flashprog_end = .;
+ _etext = .;
- . = ALIGN(8);
.rodata : {
*(.rodata)
*(.rodata.*)
}
- _etext = .;
- __data_lma = ALIGN(8);
- . = 0x24000000;
+ . = ALIGN(8);
_data = .;
- .data : AT(__data_lma) {
+ .data : {
*(.data)
*(.data.*)
}
. = ALIGN(4);
__u_boot_cmd_start = .;
- __u_boot_cmd_lma = __data_lma + (__u_boot_cmd_start - _data);
- .u_boot_cmd : AT(__u_boot_cmd_lma) {
+ .u_boot_cmd : {
KEEP(*(.u_boot_cmd))
}
__u_boot_cmd_end = .;
+ . = ALIGN(4);
+ _got = .;
+ .got : {
+ *(.got)
+ }
+ _egot = .;
+
. = ALIGN(8);
_edata = .;
- __edata_lma = __u_boot_cmd_lma + (_edata - __u_boot_cmd_start);
- .bss : AT(__edata_lma) {
+ .bss : {
*(.bss)
*(.bss.*)
}
diff --git a/board/bf533-ezkit/Makefile b/board/bf533-ezkit/Makefile
index 4fe7d78..e55c1a7 100644
--- a/board/bf533-ezkit/Makefile
+++ b/board/bf533-ezkit/Makefile
@@ -1,7 +1,7 @@
#
# U-boot - Makefile
#
-# Copyright (c) 2007 Analog Device Inc.
+# Copyright (c) 2005-2007 Analog Device Inc.
#
# (C) Copyright 2000-2006
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
diff --git a/board/bf533-ezkit/bf533-ezkit.c b/board/bf533-ezkit/bf533-ezkit.c
index feaeb00..1dd4a3f 100644
--- a/board/bf533-ezkit/bf533-ezkit.c
+++ b/board/bf533-ezkit/bf533-ezkit.c
@@ -1,7 +1,7 @@
/*
* U-boot - ezkit533.c
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <common.h>
diff --git a/board/bf533-ezkit/flash-defines.h b/board/bf533-ezkit/flash-defines.h
index e211918..bd9e859 100644
--- a/board/bf533-ezkit/flash-defines.h
+++ b/board/bf533-ezkit/flash-defines.h
@@ -1,7 +1,7 @@
/*
* U-boot - flash-defines.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef __FLASHDEFINES_H__
@@ -60,7 +60,7 @@
int erase_flash(void);
int erase_block_flash(int, unsigned long);
void unlock_flash(long lOffset);
-int write_data(long lStart, long lCount, long lStride, int *pnData);
+int write_data(long lStart, long lCount, uchar *pnData);
int FillData(long lStart, long lCount, long lStride, int *pnData);
int read_data(long lStart, long lCount, long lStride, int *pnData);
int read_flash(long nOffset, int *pnValue);
diff --git a/board/bf533-ezkit/flash.c b/board/bf533-ezkit/flash.c
index 067a260..299cdba 100644
--- a/board/bf533-ezkit/flash.c
+++ b/board/bf533-ezkit/flash.c
@@ -1,7 +1,7 @@
/*
* U-boot - flash.c Flash driver for PSD4256GV
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
* This file is based on BF533EzFlash.c originally written by Analog Devices, Inc.
*
* (C) Copyright 2000-2004
@@ -22,8 +22,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <asm/io.h>
@@ -178,63 +178,66 @@
int write_buff(flash_info_t * info, uchar * src, ulong addr, ulong cnt)
{
int ret;
-
- ret = write_data(addr, cnt, 1, (int *)src);
+ int d;
+ if (addr % 2) {
+ read_flash(addr - 1 - CFG_FLASH_BASE, &d);
+ d = (int)((d & 0x00FF) | (*src++ << 8));
+ ret = write_data(addr - 1, 2, (uchar *) & d);
+ if (ret == FLASH_FAIL)
+ return ERR_NOT_ERASED;
+ ret = write_data(addr + 1, cnt - 1, src);
+ } else
+ ret = write_data(addr, cnt, src);
if (ret == FLASH_FAIL)
return ERR_NOT_ERASED;
return FLASH_SUCCESS;
}
-int write_data(long lStart, long lCount, long lStride, int *pnData)
+int write_data(long lStart, long lCount, uchar * pnData)
{
long i = 0;
- int j = 0;
unsigned long ulOffset = lStart - CFG_FLASH_BASE;
int d;
- int iShift = 0;
- int iNumWords = 2;
- int nLeftover = lCount % 4;
int nSector = 0;
+ int flag = 0;
- for (i = 0; (i < lCount / 4) && (i < BUFFER_SIZE); i++) {
- for (iShift = 0, j = 0; (j < iNumWords);
- j++, ulOffset += (lStride * 2)) {
- if ((ulOffset >= INVALIDLOCNSTART)
- && (ulOffset < INVALIDLOCNEND)) {
- printf
- ("Invalid locations, Try writing to another location \n");
- return FLASH_FAIL;
- }
- get_sector_number(ulOffset, &nSector);
- read_flash(ulOffset, &d);
- if (d != 0xffff) {
- printf
- ("Flash not erased at offset 0x%x Please erase to reprogram \n",
- ulOffset);
- return FLASH_FAIL;
- }
- unlock_flash(ulOffset);
- if (write_flash(ulOffset, (pnData[i] >> iShift)) < 0) {
- printf("Error programming the flash \n");
- return FLASH_FAIL;
- }
- iShift += 16;
- }
+ if (lCount % 2) {
+ flag = 1;
+ lCount = lCount - 1;
}
- if (nLeftover > 0) {
- if ((ulOffset >= INVALIDLOCNSTART)
- && (ulOffset < INVALIDLOCNEND))
+
+ for (i = 0; i < lCount - 1; i += 2, ulOffset += 2) {
+ get_sector_number(ulOffset, &nSector);
+ read_flash(ulOffset, &d);
+ if (d != 0xffff) {
+ printf
+ ("Flash not erased at offset 0x%x Please erase to reprogram \n",
+ ulOffset);
+ return FLASH_FAIL;
+ }
+ unlock_flash(ulOffset);
+ d = (int)(pnData[i] | pnData[i + 1] << 8);
+ write_flash(ulOffset, d);
+ if (poll_toggle_bit(ulOffset) < 0) {
+ printf("Error programming the flash \n");
return FLASH_FAIL;
+ }
+ if ((i > 0) && (!(i % AFP_SectorSize2)))
+ printf(".");
+ }
+ if (flag) {
get_sector_number(ulOffset, &nSector);
read_flash(ulOffset, &d);
if (d != 0xffff) {
printf
- ("Flash already programmed. Please erase to reprogram \n");
- printf("uloffset = 0x%x \t d = 0x%x\n", ulOffset, d);
+ ("Flash not erased at offset 0x%x Please erase to reprogram \n",
+ ulOffset);
return FLASH_FAIL;
}
unlock_flash(ulOffset);
- if (write_flash(ulOffset, pnData[i]) < 0) {
+ d = (int)(pnData[i] | (d & 0xFF00));
+ write_flash(ulOffset, d);
+ if (poll_toggle_bit(ulOffset) < 0) {
printf("Error programming the flash \n");
return FLASH_FAIL;
}
diff --git a/board/bf533-ezkit/psd4256.h b/board/bf533-ezkit/psd4256.h
index 9776516..cc654b8 100644
--- a/board/bf533-ezkit/psd4256.h
+++ b/board/bf533-ezkit/psd4256.h
@@ -1,7 +1,7 @@
/*
* U-boot - psd4256.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
/*
diff --git a/board/bf533-stamp/Makefile b/board/bf533-stamp/Makefile
index 8223d59..02c941b 100644
--- a/board/bf533-stamp/Makefile
+++ b/board/bf533-stamp/Makefile
@@ -1,7 +1,7 @@
#
# U-boot - Makefile
#
-# Copyright (c) 2007 Analog Device Inc.
+# Copyright (c) 2005-2007 Analog Device Inc.
#
# (C) Copyright 2000-2006
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
diff --git a/board/bf533-stamp/bf533-stamp.c b/board/bf533-stamp/bf533-stamp.c
index 2f6e751..b9dff99 100644
--- a/board/bf533-stamp/bf533-stamp.c
+++ b/board/bf533-stamp/bf533-stamp.c
@@ -1,7 +1,7 @@
/*
* U-boot - stamp.c STAMP board specific routines
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <common.h>
diff --git a/board/bf533-stamp/bf533-stamp.h b/board/bf533-stamp/bf533-stamp.h
index b2b51aa..1e58e47 100644
--- a/board/bf533-stamp/bf533-stamp.h
+++ b/board/bf533-stamp/bf533-stamp.h
@@ -1,7 +1,7 @@
/*
* U-boot - stamp.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef __STAMP_H__
diff --git a/board/bf537-stamp/bf537-stamp.c b/board/bf537-stamp/bf537-stamp.c
index cc4e998..47f7c9e 100644
--- a/board/bf537-stamp/bf537-stamp.c
+++ b/board/bf537-stamp/bf537-stamp.c
@@ -1,7 +1,7 @@
/*
* U-boot - BF537.c
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <common.h>
diff --git a/board/bf537-stamp/flash-defines.h b/board/bf537-stamp/flash-defines.h
index f19e171..acc1e86 100644
--- a/board/bf537-stamp/flash-defines.h
+++ b/board/bf537-stamp/flash-defines.h
@@ -1,7 +1,7 @@
/*
* U-boot - flash-defines.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef __FLASHDEFINES_H__
diff --git a/board/bf537-stamp/flash.c b/board/bf537-stamp/flash.c
index 42dcf06..ed85841 100644
--- a/board/bf537-stamp/flash.c
+++ b/board/bf537-stamp/flash.c
@@ -1,7 +1,7 @@
/*
* U-boot - flash.c Flash driver for PSD4256GV
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
* This file is based on BF533EzFlash.c originally written by Analog Devices, Inc.
*
* (C) Copyright 2000-2004
@@ -22,8 +22,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <malloc.h>
diff --git a/board/bf561-ezkit/bf561-ezkit.c b/board/bf561-ezkit/bf561-ezkit.c
index 71281c0..989b019 100644
--- a/board/bf561-ezkit/bf561-ezkit.c
+++ b/board/bf561-ezkit/bf561-ezkit.c
@@ -2,7 +2,7 @@
* U-boot - ezkit561.c
*
* Copyright (c) 2005 Bas Vermeulen <bas@buyways.nl>
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -22,8 +22,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <common.h>
diff --git a/board/icecube/icecube.c b/board/icecube/icecube.c
index 700c9d9..2960998 100644
--- a/board/icecube/icecube.c
+++ b/board/icecube/icecube.c
@@ -42,6 +42,53 @@
#include "mt48lc16m16a2-75.h"
# endif
#endif
+
+#ifdef CONFIG_LITE5200B_PM
+/* u-boot part of low-power mode implementation */
+#define SAVED_ADDR (*(void **)0x00000000)
+#define PSC2_4 0x02
+
+void lite5200b_wakeup(void)
+{
+ unsigned char wakeup_pin;
+ void (*linux_wakeup)(void);
+
+ /* check PSC2_4, if it's down "QT" is signaling we have a wakeup
+ * from low power mode */
+ *(vu_char *)MPC5XXX_WU_GPIO_ENABLE = PSC2_4;
+ __asm__ volatile ("sync");
+
+ wakeup_pin = *(vu_char *)MPC5XXX_WU_GPIO_DATA_I;
+ if (wakeup_pin & PSC2_4)
+ return;
+
+ /* acknowledge to "QT"
+ * by holding pin at 1 for 10 uS */
+ *(vu_char *)MPC5XXX_WU_GPIO_DIR = PSC2_4;
+ __asm__ volatile ("sync");
+ *(vu_char *)MPC5XXX_WU_GPIO_DATA_O = PSC2_4;
+ __asm__ volatile ("sync");
+ udelay(10);
+
+ /* put ram out of self-refresh */
+ *(vu_long *)MPC5XXX_SDRAM_CTRL |= 0x80000000; /* mode_en */
+ __asm__ volatile ("sync");
+ *(vu_long *)MPC5XXX_SDRAM_CTRL |= 0x50000000; /* cke ref_en */
+ __asm__ volatile ("sync");
+ *(vu_long *)MPC5XXX_SDRAM_CTRL &= ~0x80000000; /* !mode_en */
+ __asm__ volatile ("sync");
+ udelay(10); /* wait a bit */
+
+ /* jump back to linux kernel code */
+ linux_wakeup = SAVED_ADDR;
+ printf("\n\nLooks like we just woke, transferring control to 0x%08lx\n",
+ linux_wakeup);
+ linux_wakeup();
+}
+#else
+#define lite5200b_wakeup()
+#endif
+
#ifndef CFG_RAMBOOT
static void sdram_start (int hi_addr)
{
@@ -208,6 +255,8 @@
__asm__ volatile ("sync");
}
+ lite5200b_wakeup();
+
return dramsize + dramsize2;
}
diff --git a/board/mcc200/lcd.c b/board/mcc200/lcd.c
index 98b86d1..726366d 100644
--- a/board/mcc200/lcd.c
+++ b/board/mcc200/lcd.c
@@ -180,10 +180,6 @@
break;
udelay (PSOC_WAIT_TIME);
}
- if (!retries) {
- printf ("%s Warning: PSoC doesn't respond on "
- "RTS NEGATE\n", __FUNCTION__);
- }
return;
}
diff --git a/board/mpc7448hpc2/Makefile b/board/mpc7448hpc2/Makefile
new file mode 100644
index 0000000..e3d757d
--- /dev/null
+++ b/board/mpc7448hpc2/Makefile
@@ -0,0 +1,52 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := $(BOARD).o tsi108_init.o
+SOBJS := asm_init.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+.PHONY: distclean
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude ($obj).depend
+
+#########################################################################
diff --git a/board/mpc7448hpc2/asm_init.S b/board/mpc7448hpc2/asm_init.S
new file mode 100644
index 0000000..a7a40a1
--- /dev/null
+++ b/board/mpc7448hpc2/asm_init.S
@@ -0,0 +1,918 @@
+/*
+ * (C) Copyright 2004-05; Tundra Semiconductor Corp.
+ *
+ * Added automatic detect of SDC settings
+ * Copyright (c) 2005 Freescale Semiconductor, Inc.
+ * Maintainer tie-fei.zang@freescale.com
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * FILENAME: asm_init.s
+ *
+ * Originator: Alex Bounine
+ *
+ * DESCRIPTION:
+ * Initialization code for the Tundra Tsi108 bridge chip
+ *
+ */
+
+#include <config.h>
+#include <version.h>
+
+#include <ppc_asm.tmpl>
+#include <ppc_defs.h>
+#include <asm/processor.h>
+
+#include <tsi108.h>
+
+/*
+ * Build Configuration Options
+ */
+
+/* #define DISABLE_PBM disables usage of PB Master */
+/* #define SDC_HARDCODED_INIT config SDRAM controller with hardcoded values */
+/* #define SDC_AUTOPRECH_EN enable SDRAM auto precharge */
+
+/*
+ * Hardcoded SDC settings
+ */
+
+#ifdef SDC_HARDCODED_INIT
+
+/* Micron MT9HTF6472AY-40EA1 : Unbuffered, 512MB, 400, CL3, Single Rank */
+
+#define VAL_SD_REFRESH (0x61A)
+#define VAL_SD_TIMING (0x0308336b)
+#define VAL_SD_D0_CTRL (0x07100021) /* auto-precharge disabled */
+#define VAL_SD_D0_BAR (0x0FE00000) /* 512MB @ 0x00000000 */
+#define VAL_SD_D1_CTRL (0x07100021) /* auto-precharge disabled */
+#define VAL_SD_D1_BAR (0x0FE00200) /* 512MB @ 0x20000000 */
+
+#endif /* SDC_HARDCODED_INIT */
+
+/*
+ CPU Configuration:
+
+ CPU Address and Data Parity enables.
+
+#define CPU_AP
+#define CPU_DP
+*/
+
+/*
+ * Macros
+ * !!! Attention !!! Macros LOAD_PTR, LOAD_U32 and LOAD_MEM defined below are
+ * expected to work correctly for the CSR space within 32KB range.
+ *
+ * LOAD_PTR and LOAD_U32 - load specified register with a 32 bit constant.
+ * These macros are absolutely identical except their names. This difference
+ * is provided intentionally for better readable code.
+ */
+
+#define LOAD_PTR(reg,const32) \
+ addis reg,r0,const32@h; ori reg,reg,const32@l
+
+#define LOAD_U32(reg,const32) \
+ addis reg,r0,const32@h; ori reg,reg,const32@l
+
+/* LOADMEM initializes a register with the contents of a specified 32-bit
+ * memory location, usually a CSR value.
+ */
+
+#define LOAD_MEM(reg,addr32) \
+ addis reg,r0,addr32@ha; lwz reg,addr32@l(reg)
+
+#ifndef SDC_HARDCODED_INIT
+sdc_clk_sync:
+ /* MHz: 0,0,183,100,133,167,200,233 */
+ .long 0, 0, 6, 10, 8, 6, 5, 4 /* nSec */
+#endif
+
+/*
+ * board_asm_init() - early initialization function. Coded to be portable to
+ * dual-CPU configuration.
+ * Checks CPU number and performs board HW initialization if called for CPU0.
+ * Registers used: r3,r4,r5,r6,r19,r29
+ *
+ * NOTE: For dual-CPU configuration only CPU0 is allowed to configure Tsi108
+ * and the rest of the board. Current implementation demonstrates two
+ * possible ways to identify CPU number:
+ * - for MPC74xx platform: uses MSSCR0[ID] bit as defined in UM.
+ * - for PPC750FX/GX boards: uses WHO_AM_I bit reported by Tsi108.
+ */
+
+ .globl board_asm_init
+board_asm_init:
+ mflr r19 /* Save LR to be able return later. */
+ bl icache_enable /* Enable icache to reduce reads from flash. */
+
+/* Initialize pointer to Tsi108 register space */
+
+ LOAD_PTR(r29,CFG_TSI108_CSR_RST_BASE)/* r29 - pointer to tsi108 CSR space */
+ ori r4,r29,TSI108_PB_REG_OFFSET
+
+/* Check Processor Version Number */
+
+ mfspr r3, PVR
+ rlwinm r3,r3,16,16,23 /* get ((Processor Version Number) & 0xFF00) */
+
+ cmpli 0,0,r3,0x8000 /* MPC74xx */
+ bne cont_brd_init
+
+ /*
+ * For MPC744x/5x enable extended BATs[4-7]
+ * Sri: Set HIGH_BAT_EN and XBSEN, and SPD =1
+ * to disable prefetch
+ */
+
+ mfspr r5, HID0
+ oris r5, r5, 0x0080 /* Set HID0[HIGH_BAT_EN] bit #8 */
+ ori r5, r5, 0x0380 /* Set SPD,XBSEN,SGE bits #22,23,24 */
+ mtspr HID0, r5
+ isync
+ sync
+
+ /* Adding code to disable external interventions in MPX bus mode */
+ mfspr r3, 1014
+ oris r3, r3, 0x0100 /* Set the EIDIS bit in MSSCR0: bit 7 */
+ mtspr 1014, r3
+ isync
+ sync
+
+ /* Sri: code to enable FP unit */
+ mfmsr r3
+ ori r3, r3, 0x2000
+ mtmsr r3
+ isync
+ sync
+
+ /* def CONFIG_DUAL_CPU
+ * For MPC74xx processor, use MSSCR0[ID] bit to identify CPU number.
+ */
+#if(1)
+ mfspr r3,1014 /* read MSSCR0 */
+ rlwinm. r3,r3,27,31,31 /* get processor ID number */
+ mtspr SPRN_PIR,r3 /* Save CPU ID */
+ sync
+ bne init_done
+ b do_tsi108_init
+
+cont_brd_init:
+
+ /* An alternative method of checking the processor number (in addition
+ * to configuration using MSSCR0[ID] bit on MPC74xx).
+ * Good for IBM PPC750FX/GX.
+ */
+
+ lwz r3,PB_BUS_MS_SELECT(r4) /* read PB_ID register */
+ rlwinm. r3,r3,24,31,31 /* get processor ID number */
+ bne init_done
+#else
+
+cont_brd_init:
+
+#endif /* CONFIG_DUAL_CPU */
+
+ /* Initialize Tsi108 chip */
+
+do_tsi108_init:
+
+ /*
+ * Adjust HLP/Flash parameters. By default after reset the HLP port is
+ * set to support slow devices. Better performance can be achived when
+ * an optimal parameters are used for specific EPROM device.
+ * NOTE: This should be performed ASAP for the emulation platform
+ * because it has 5MHz HLP clocking.
+ */
+
+#ifdef CONFIG_TSI108EMU
+ ori r4,r29,TSI108_HLP_REG_OFFSET
+ LOAD_U32(r5,0x434422c0)
+ stw r5,0x08(r4) /* set HLP B0_CTRL0 */
+ sync
+ LOAD_U32(r5,0xd0012000)
+ stw r5,0x0c(r4) /* set HLP B0_CTRL1 */
+ sync
+#endif
+
+ /* Initialize PB interface. */
+
+ ori r4,r29,TSI108_PB_REG_OFFSET
+
+#if (CFG_TSI108_CSR_BASE != CFG_TSI108_CSR_RST_BASE)
+ /* Relocate (if required) Tsi108 registers. Set new value for
+ * PB_REG_BAR:
+ * Note we are in the 32-bit address mode.
+ */
+ LOAD_U32(r5,(CFG_TSI108_CSR_BASE | 0x01)) /* PB_REG_BAR: BA + EN */
+ stw r5,PB_REG_BAR(r4)
+ andis. r29,r5,0xFFFF
+ sync
+ ori r4,r29,TSI108_PB_REG_OFFSET
+#endif
+
+ /* Set PB Slave configuration register */
+
+ LOAD_U32(r5,0x00002481) /* PB_SCR: TEA enabled,AACK delay = 1 */
+ lwz r3, PB_RSR(r4) /* get PB bus mode */
+ xori r3,r3,0x0001 /* mask PB_BMODE: r3 -> (0 = 60X, 1 = MPX) */
+ rlwimi r5,r3,14,17,17 /* for MPX: set DTI_MODE bit */
+ stw r5,PB_SCR(r4)
+ sync
+
+ /* Configure PB Arbiter */
+
+ lwz r5,PB_ARB_CTRL(r4) /* Read PB Arbiter Control Register */
+ li r3, 0x00F0 /* ARB_PIPELINE_DEP mask */
+#ifdef DISABLE_PBM
+ ori r3,r3,0x1000 /* add PBM_EN to clear (enabled by default) */
+#endif
+ andc r5,r5,r3 /* Clear the masked bit fields */
+ ori r5,r5,0x0001 /* Set pipeline depth */
+ stw r5,PB_ARB_CTRL(r4)
+
+#if (0) /* currently using the default settings for PBM after reset */
+ LOAD_U32(r5,0x) /* value for PB_MCR */
+ stw r5,PB_MCR(r4)
+ sync
+
+ LOAD_U32(r5,0x) /* value for PB_MCMD */
+ stw r5,PB_MCMD(r4)
+ sync
+#endif
+
+ /* Disable or enable PVT based on processor bus frequency
+ * 1. Read CG_PWRUP_STATUS register field bits 18,17,16
+ * 2. See if the value is < or > 133mhz (18:16 = 100)
+ * 3. If > enable PVT
+ */
+
+ LOAD_U32(r3,0xC0002234)
+ lwz r3,0(r3)
+ rlwinm r3,r3,16,29,31
+
+ cmpi 0,0,r3,0x0004
+ bgt sdc_init
+
+#ifndef CONFIG_TSI108EMU
+ /* FIXME: Disable PB calibration control for any real Tsi108 board */
+ li r5,0x0101 /* disable calibration control */
+ stw r5,PB_PVT_CTRL2(r4)
+ sync
+#endif
+
+ /* Initialize SDRAM controller. */
+
+sdc_init:
+
+#ifndef SDC_HARDCODED_INIT
+ /* get SDC clock prior doing sdram controller autoconfig */
+ ori r4,r29,TSI108_CLK_REG_OFFSET /* r4 - ptr to CG registers */
+ lwz r3, CG_PWRUP_STATUS(r4) /* get CG configuration */
+ rlwinm r3,r3,12,29,31 /* r3 - SD clk */
+ lis r5,sdc_clk_sync@h
+ ori r5,r5,sdc_clk_sync@l
+ /* Sri: At this point check if r3 = 001. If yes,
+ * the memory frequency should be same as the
+ * MPX bus frequency
+ */
+ cmpi 0,0,r3,0x0001
+ bne get_nsec
+ lwz r6, CG_PWRUP_STATUS(r4)
+ rlwinm r6,r6,16,29,31
+ mr r3,r6
+
+get_nsec:
+ rlwinm r3,r3,2,0,31
+ lwzx r9,r5,r3 /* get SD clk rate in nSec */
+ /* ATTN: r9 will be used by SPD routine */
+#endif /* !SDC_HARDCODED_INIT */
+
+ ori r4,r29,TSI108_SD_REG_OFFSET /* r4 - ptr to SDRAM registers */
+
+ /* Initialize SDRAM controller. SDRAM Size = 512MB, One DIMM. */
+
+ LOAD_U32(r5,0x00)
+ stw r5,SD_INT_ENABLE(r4) /* Ensure that interrupts are disabled */
+#ifdef ENABLE_SDRAM_ECC
+ li r5, 0x01
+#endif /* ENABLE_SDRAM_ECC */
+ stw r5,SD_ECC_CTRL(r4) /* Enable/Disable ECC */
+ sync
+
+#ifdef SDC_HARDCODED_INIT /* config sdram controller with hardcoded values */
+
+ /* First read the CG_PWRUP_STATUS register to get the
+ * memory speed from bits 22,21,20
+ */
+
+ LOAD_U32(r3,0xC0002234)
+ lwz r3,0(r3)
+ rlwinm r3,r3,12,29,31
+
+ /* Now first check for 166, then 200, or default */
+
+ cmpi 0,0,r3,0x0005
+ bne check_for_200mhz
+
+ /* set values for 166 Mhz memory speed
+ * Set refresh rate and timing parameters
+ */
+ LOAD_U32(r5,0x00000515)
+ stw r5,SD_REFRESH(r4)
+ LOAD_U32(r5,0x03073368)
+ stw r5,SD_TIMING(r4)
+ sync
+
+ /* Initialize DIMM0 control and BAR registers */
+ LOAD_U32(r5,VAL_SD_D0_CTRL) /* auto-precharge disabled */
+#ifdef SDC_AUTOPRECH_EN
+ oris r5,r5,0x0001 /* set auto precharge EN bit */
+#endif
+ stw r5,SD_D0_CTRL(r4)
+ LOAD_U32(r5,VAL_SD_D0_BAR)
+ stw r5,SD_D0_BAR(r4)
+ sync
+
+ /* Initialize DIMM1 control and BAR registers
+ * (same as dimm 0, next 512MB, disabled)
+ */
+ LOAD_U32(r5,VAL_SD_D1_CTRL) /* auto-precharge disabled */
+#ifdef SDC_AUTOPRECH_EN
+ oris r5,r5,0x0001 /* set auto precharge EN bit */
+#endif
+ stw r5,SD_D1_CTRL(r4)
+ LOAD_U32(r5,VAL_SD_D1_BAR)
+ stw r5,SD_D1_BAR(r4)
+ sync
+
+ b sdc_init_done
+
+check_for_200mhz:
+
+ cmpi 0,0,r3,0x0006
+ bne set_default_values
+
+ /* set values for 200Mhz memory speed
+ * Set refresh rate and timing parameters
+ */
+ LOAD_U32(r5,0x0000061a)
+ stw r5,SD_REFRESH(r4)
+ LOAD_U32(r5,0x03083348)
+ stw r5,SD_TIMING(r4)
+ sync
+
+ /* Initialize DIMM0 control and BAR registers */
+ LOAD_U32(r5,VAL_SD_D0_CTRL) /* auto-precharge disabled */
+#ifdef SDC_AUTOPRECH_EN
+ oris r5,r5,0x0001 /* set auto precharge EN bit */
+#endif
+ stw r5,SD_D0_CTRL(r4)
+ LOAD_U32(r5,VAL_SD_D0_BAR)
+ stw r5,SD_D0_BAR(r4)
+ sync
+
+ /* Initialize DIMM1 control and BAR registers
+ * (same as dimm 0, next 512MB, disabled)
+ */
+ LOAD_U32(r5,VAL_SD_D1_CTRL) /* auto-precharge disabled */
+#ifdef SDC_AUTOPRECH_EN
+ oris r5,r5,0x0001 /* set auto precharge EN bit */
+#endif
+ stw r5,SD_D1_CTRL(r4)
+ LOAD_U32(r5,VAL_SD_D1_BAR)
+ stw r5,SD_D1_BAR(r4)
+ sync
+
+ b sdc_init_done
+
+set_default_values:
+
+ /* Set refresh rate and timing parameters */
+ LOAD_U32(r5,VAL_SD_REFRESH)
+ stw r5,SD_REFRESH(r4)
+ LOAD_U32(r5,VAL_SD_TIMING)
+ stw r5,SD_TIMING(r4)
+ sync
+
+ /* Initialize DIMM0 control and BAR registers */
+ LOAD_U32(r5,VAL_SD_D0_CTRL) /* auto-precharge disabled */
+#ifdef SDC_AUTOPRECH_EN
+ oris r5,r5,0x0001 /* set auto precharge EN bit */
+#endif
+ stw r5,SD_D0_CTRL(r4)
+ LOAD_U32(r5,VAL_SD_D0_BAR)
+ stw r5,SD_D0_BAR(r4)
+ sync
+
+ /* Initialize DIMM1 control and BAR registers
+ * (same as dimm 0, next 512MB, disabled)
+ */
+ LOAD_U32(r5,VAL_SD_D1_CTRL) /* auto-precharge disabled */
+#ifdef SDC_AUTOPRECH_EN
+ oris r5,r5,0x0001 /* set auto precharge EN bit */
+#endif
+ stw r5,SD_D1_CTRL(r4)
+ LOAD_U32(r5,VAL_SD_D1_BAR)
+ stw r5,SD_D1_BAR(r4)
+ sync
+#else /* !SDC_HARDCODED_INIT */
+ bl tsi108_sdram_spd /* automatically detect SDC settings */
+#endif /* SDC_HARDCODED_INIT */
+
+sdc_init_done:
+
+#ifdef DISABLE_PBM
+ LOAD_U32(r5,0x00000030) /* PB_EN + OCN_EN */
+#else
+ LOAD_U32(r5,0x00000230) /* PB_EN + OCN_EN + PB/OCN=80/20 */
+#endif /* DISABLE_PBM */
+
+#ifdef CONFIG_TSI108EMU
+ oris r5,r5,0x0010 /* set EMULATION_MODE bit */
+#endif
+
+ stw r5,SD_CTRL(r4)
+ eieio
+ sync
+
+ /* Enable SDRAM access */
+
+ oris r5,r5,0x8000 /* start SDC: set SD_CTRL[ENABLE] bit */
+ stw r5,SD_CTRL(r4)
+ sync
+
+wait_init_complete:
+ lwz r5,SD_STATUS(r4)
+ andi. r5,r5,0x0001
+ /* wait until SDRAM initialization is complete */
+ beq wait_init_complete
+
+ /* Map SDRAM into the processor bus address space */
+
+ ori r4,r29,TSI108_PB_REG_OFFSET
+
+ /* Setup BARs associated with direct path PB<->SDRAM */
+
+ /* PB_SDRAM_BAR1:
+ * provides a direct path to the main system memory (cacheable SDRAM)
+ */
+
+ /* BA=0,Size=512MB, ENable, No Addr.Translation */
+ LOAD_U32(r5, 0x00000011)
+ stw r5,PB_SDRAM_BAR1(r4)
+ sync
+
+ /* Make sure that PB_SDRAM_BAR1 decoder is set
+ * (to allow following immediate read from SDRAM)
+ */
+ lwz r5,PB_SDRAM_BAR1(r4)
+ sync
+
+ /* PB_SDRAM_BAR2:
+ * provides non-cacheable alias (via the direct path) to main
+ * system memory.
+ * Size = 512MB, ENable, Addr.Translation - ON,
+ * BA = 0x0_40000000, TA = 0x0_00000000
+ */
+
+ LOAD_U32(r5, 0x40010011)
+ stw r5,PB_SDRAM_BAR2(r4)
+ sync
+
+ /* Make sure that PB_SDRAM_BAR2 decoder is set
+ * (to allow following immediate read from SDRAM)
+ */
+ lwz r5,PB_SDRAM_BAR2(r4)
+ sync
+
+init_done:
+
+ /* All done. Restore LR and return. */
+ mtlr r19
+ blr
+
+#if (0)
+ /*
+ * init_cpu1
+ * This routine enables CPU1 on the dual-processor system.
+ * Now there is only one processor in the system
+ */
+
+ .global enable_cpu1
+enable_cpu1:
+
+ lis r3,Tsi108_Base@ha /* Get Grendel CSR Base Addr */
+ addi r3,r3,Tsi108_Base@l
+ lwz r3,0(r3) /* R3 = CSR Base Addr */
+ ori r4,r3,TSI108_PB_REG_OFFSET
+ lwz r3,PB_ARB_CTRL(r4) /* Read PB Arbiter Control Register */
+ ori r3,r3,0x0200 /* Set M1_EN bit */
+ stw r3,PB_ARB_CTRL(r4)
+
+ blr
+#endif
+
+ /*
+ * enable_EI
+ * Enable CPU core external interrupt
+ */
+
+ .global enable_EI
+enable_EI:
+ mfmsr r3
+ ori r3,r3,0x8000 /* set EE bit */
+ mtmsr r3
+ blr
+
+ /*
+ * disable_EI
+ * Disable CPU core external interrupt
+ */
+
+ .global disable_EI
+disable_EI:
+ mfmsr r3
+ li r4,-32768 /* aka "li r4,0x8000" */
+ andc r3,r3,r4 /* clear EE bit */
+ mtmsr r3
+ blr
+
+#ifdef ENABLE_SDRAM_ECC
+ /* enables SDRAM ECC */
+
+ .global enable_ECC
+enable_ECC:
+ ori r4,r29,TSI108_SD_REG_OFFSET
+ lwz r3,SD_ECC_CTRL(r4) /* Read SDRAM ECC Control Register */
+ ori r3,r3,0x0001 /* Set ECC_EN bit */
+ stw r3,SD_ECC_CTRL(r4)
+ blr
+
+ /*
+ * clear_ECC_err
+ * Clears all pending SDRAM ECC errors
+ * (normally after SDRAM scrubbing/initialization)
+ */
+
+ .global clear_ECC_err
+clear_ECC_err:
+ ori r4,r29,TSI108_SD_REG_OFFSET
+ ori r3,r0,0x0030 /* ECC_UE_INT + ECC_CE_INT bits */
+ stw r3,SD_INT_STATUS(r4)
+ blr
+
+#endif /* ENABLE_SDRAM_ECC */
+
+#ifndef SDC_HARDCODED_INIT
+
+ /* SDRAM SPD Support */
+#define SD_I2C_CTRL1 (0x400)
+#define SD_I2C_CTRL2 (0x404)
+#define SD_I2C_RD_DATA (0x408)
+#define SD_I2C_WR_DATA (0x40C)
+
+ /*
+ * SDRAM SPD Support Macros
+ */
+
+#define SPD_DIMM0 (0x00000100)
+#define SPD_DIMM1 (0x00000200) /* SPD_DIMM1 was 0x00000000 */
+
+#define SPD_RDIMM (0x01)
+#define SPD_UDIMM (0x02)
+
+#define SPD_CAS_3 0x8
+#define SPD_CAS_4 0x10
+#define SPD_CAS_5 0x20
+
+#define ERR_NO_DIMM_FOUND (0xdb0)
+#define ERR_TRAS_FAIL (0xdb1)
+#define ERR_TRCD_FAIL (0xdb2)
+#define ERR_TRP_FAIL (0xdb3)
+#define ERR_TWR_FAIL (0xdb4)
+#define ERR_UNKNOWN_PART (0xdb5)
+#define ERR_NRANK_INVALID (0xdb6)
+#define ERR_DIMM_SIZE (0xdb7)
+#define ERR_ADDR_MODE (0xdb8)
+#define ERR_RFRSH_RATE (0xdb9)
+#define ERR_DIMM_TYPE (0xdba)
+#define ERR_CL_VALUE (0xdbb)
+#define ERR_TRFC_FAIL (0xdbc)
+
+/* READ_SPD requirements:
+ * byte - byte address in SPD device (0 - 255)
+ * r3 = will return data read from I2C Byte location
+ * r4 - unchanged (SDC base addr)
+ * r5 - clobbered in routine (I2C status)
+ * r10 - number of DDR slot where first SPD device is detected
+ */
+
+#define READ_SPD(byte_num) \
+ addis r3, 0, byte_num@l; \
+ or r3, r3, r10; \
+ ori r3, r3, 0x0A; \
+ stw r3, SD_I2C_CTRL1(r4); \
+ li r3, I2C_CNTRL2_START; \
+ stw r3, SD_I2C_CTRL2(r4); \
+ eieio; \
+ sync; \
+ li r3, 0x100; \
+1:; \
+ addic. r3, r3, -1; \
+ bne 1b; \
+2:; \
+ lwz r5, SD_I2C_CTRL2(r4); \
+ rlwinm. r3,r5,0,23,23; \
+ bne 2b; \
+ rlwinm. r3,r5,0,3,3; \
+ lwz r3,SD_I2C_RD_DATA(r4)
+
+#define SPD_MIN_RFRSH (0x80)
+#define SPD_MAX_RFRSH (0x85)
+
+refresh_rates: /* in nSec */
+ .long 15625 /* Normal (0x80) */
+ .long 3900 /* Reduced 0.25x (0x81) */
+ .long 7800 /* Reduced 0.5x (0x82) */
+ .long 31300 /* Extended 2x (0x83) */
+ .long 62500 /* Extended 4x (0x84) */
+ .long 125000 /* Extended 8x (0x85) */
+
+/*
+ * tsi108_sdram_spd
+ *
+ * Inittializes SDRAM Controller using DDR2 DIMM Serial Presence Detect data
+ * Uses registers: r4 - SDC base address (not changed)
+ * r9 - SDC clocking period in nSec
+ * Changes registers: r3,r5,r6,r7,r8,r10,r11
+ */
+
+tsi108_sdram_spd:
+
+ li r10,SPD_DIMM0
+ xor r11,r11,r11 /* DIMM Base Address: starts from 0 */
+
+do_first_dimm:
+
+ /* Program Refresh Rate Register */
+
+ READ_SPD(12) /* get Refresh Rate */
+ beq check_next_slot
+ li r5, ERR_RFRSH_RATE
+ cmpi 0,0,r3,SPD_MIN_RFRSH
+ ble spd_fail
+ cmpi 0,0,r3,SPD_MAX_RFRSH
+ bgt spd_fail
+ addi r3,r3,-SPD_MIN_RFRSH
+ rlwinm r3,r3,2,0,31
+ lis r5,refresh_rates@h
+ ori r5,r5,refresh_rates@l
+ lwzx r5,r5,r3 /* get refresh rate in nSec */
+ divwu r5,r5,r9 /* calculate # of SDC clocks */
+ stw r5,SD_REFRESH(r4) /* Set refresh rate */
+ sync
+
+ /* Program SD Timing Register */
+
+ li r7, 0 /* clear r7 prior parameter collection */
+
+ READ_SPD(20) /* get DIMM type: Registered or Unbuffered */
+ beq spd_read_fail
+ li r5, ERR_DIMM_TYPE
+ cmpi 0,0,r3,SPD_UDIMM
+ beq do_cl
+ cmpi 0,0,r3,SPD_RDIMM
+ bne spd_fail
+ oris r7,r7,0x1000 /* set SD_TIMING[DIMM_TYPE] bit */
+
+do_cl:
+ READ_SPD(18) /* Get CAS Latency */
+ beq spd_read_fail
+ li r5,ERR_CL_VALUE
+ andi. r6,r3,SPD_CAS_3
+ beq cl_4
+ li r6,3
+ b set_cl
+cl_4:
+ andi. r6,r3,SPD_CAS_4
+ beq cl_5
+ li r6,4
+ b set_cl
+cl_5:
+ andi. r6,r3,SPD_CAS_5
+ beq spd_fail
+ li r6,5
+set_cl:
+ rlwimi r7,r6,24,5,7
+
+ READ_SPD(30) /* Get tRAS */
+ beq spd_read_fail
+ divwu r6,r3,r9
+ mullw r8,r6,r9
+ subf. r8,r8,r3
+ beq set_tras
+ addi r6,r6,1
+set_tras:
+ li r5,ERR_TRAS_FAIL
+ cmpi 0,0,r6,0x0F /* max supported value */
+ bgt spd_fail
+ rlwimi r7,r6,16,12,15
+
+ READ_SPD(29) /* Get tRCD */
+ beq spd_read_fail
+ /* right shift tRCD by 2 bits as per DDR2 spec */
+ rlwinm r3,r3,30,2,31
+ divwu r6,r3,r9
+ mullw r8,r6,r9
+ subf. r8,r8,r3
+ beq set_trcd
+ addi r6,r6,1
+set_trcd:
+ li r5,ERR_TRCD_FAIL
+ cmpi 0,0,r6,0x07 /* max supported value */
+ bgt spd_fail
+ rlwimi r7,r6,12,17,19
+
+ READ_SPD(27) /* Get tRP value */
+ beq spd_read_fail
+ rlwinm r3,r3,30,2,31 /* right shift tRP by 2 bits as per DDR2 spec */
+ divwu r6,r3,r9
+ mullw r8,r6,r9
+ subf. r8,r8,r3
+ beq set_trp
+ addi r6,r6,1
+set_trp:
+ li r5,ERR_TRP_FAIL
+ cmpi 0,0,r6,0x07 /* max supported value */
+ bgt spd_fail
+ rlwimi r7,r6,8,21,23
+
+ READ_SPD(36) /* Get tWR value */
+ beq spd_read_fail
+ rlwinm r3,r3,30,2,31 /* right shift tWR by 2 bits as per DDR2 spec */
+ divwu r6,r3,r9
+ mullw r8,r6,r9
+ subf. r8,r8,r3
+ beq set_twr
+ addi r6,r6,1
+set_twr:
+ addi r6,r6,-1 /* Tsi108 SDC always gives one extra clock */
+ li r5,ERR_TWR_FAIL
+ cmpi 0,0,r6,0x07 /* max supported value */
+ bgt spd_fail
+ rlwimi r7,r6,5,24,26
+
+ READ_SPD(42) /* Get tRFC */
+ beq spd_read_fail
+ li r5, ERR_TRFC_FAIL
+ /* Tsi108 spec: tRFC=(tRFC + 1)/2 */
+ addi r3,r3,1
+ rlwinm. r3,r3,31,1,31 /* divide by 2 */
+ beq spd_fail
+ divwu r6,r3,r9
+ mullw r8,r6,r9
+ subf. r8,r8,r3
+ beq set_trfc
+ addi r6,r6,1
+set_trfc:
+ cmpi 0,0,r6,0x1F /* max supported value */
+ bgt spd_fail
+ rlwimi r7,r6,0,27,31
+
+ stw r7,SD_TIMING(r4)
+ sync
+
+ /*
+ * The following two registers are set on per-DIMM basis.
+ * The SD_REFRESH and SD_TIMING settings are common for both DIMMS
+ */
+
+do_each_dimm:
+
+ /* Program SDRAM DIMM Control Register */
+
+ li r7, 0 /* clear r7 prior parameter collection */
+
+ READ_SPD(13) /* Get Primary SDRAM Width */
+ beq spd_read_fail
+ cmpi 0,0,r3,4 /* Check for 4-bit SDRAM */
+ beq do_nbank
+ oris r7,r7,0x0010 /* Set MEM_WIDTH bit */
+
+do_nbank:
+ READ_SPD(17) /* Get Number of banks on SDRAM device */
+ beq spd_read_fail
+ /* Grendel only distinguish betw. 4 or 8-bank memory parts */
+ li r5,ERR_UNKNOWN_PART /* non-supported memory part */
+ cmpi 0,0,r3,4
+ beq do_nrank
+ cmpi 0,0,r3,8
+ bne spd_fail
+ ori r7,r7,0x1000
+
+do_nrank:
+ READ_SPD(5) /* Get # of Ranks */
+ beq spd_read_fail
+ li r5,ERR_NRANK_INVALID
+ andi. r6,r3,0x7 /* Use bits [2..0] only */
+ beq do_addr_mode
+ cmpi 0,0,r6,1
+ bgt spd_fail
+ rlwimi r7,r6,8,23,23
+
+do_addr_mode:
+ READ_SPD(4) /* Get # of Column Addresses */
+ beq spd_read_fail
+ li r5, ERR_ADDR_MODE
+ andi. r3,r3,0x0f /* cut off reserved bits */
+ cmpi 0,0,r3,8
+ ble spd_fail
+ cmpi 0,0,r3,15
+ bgt spd_fail
+ addi r6,r3,-8 /* calculate ADDR_MODE parameter */
+ rlwimi r7,r6,4,24,27 /* set ADDR_MODE field */
+
+set_dimm_ctrl:
+#ifdef SDC_AUTOPRECH_EN
+ oris r7,r7,0x0001 /* set auto precharge EN bit */
+#endif
+ ori r7,r7,1 /* set ENABLE bit */
+ cmpi 0,0,r10,SPD_DIMM0
+ bne 1f
+ stw r7,SD_D0_CTRL(r4)
+ sync
+ b set_dimm_bar
+1:
+ stw r7,SD_D1_CTRL(r4)
+ sync
+
+
+ /* Program SDRAM DIMMx Base Address Register */
+
+set_dimm_bar:
+ READ_SPD(5) /* get # of Ranks */
+ beq spd_read_fail
+ andi. r7,r3,0x7
+ addi r7,r7,1
+ READ_SPD(31) /* Read DIMM rank density */
+ beq spd_read_fail
+ rlwinm r5,r3,27,29,31
+ rlwinm r6,r3,3,24,28
+ or r5,r6,r5 /* r5 = Normalized Rank Density byte */
+ lis r8, 0x0080 /* 128MB >> 4 */
+ mullw r8,r8,r5 /* r8 = (rank_size >> 4) */
+ mullw r8,r8,r7 /* r8 = (DIMM_size >> 4) */
+ neg r7,r8
+ rlwinm r7,r7,28,4,31
+ or r7,r7,r11 /* set ADDR field */
+ rlwinm r8,r8,12,20,31
+ add r11,r11,r8 /* set Base Addr for next DIMM */
+
+ cmpi 0,0,r10,SPD_DIMM0
+ bne set_dimm1_size
+ stw r7,SD_D0_BAR(r4)
+ sync
+ li r10,SPD_DIMM1
+ READ_SPD(0)
+ bne do_each_dimm
+ b spd_done
+
+set_dimm1_size:
+ stw r7,SD_D1_BAR(r4)
+ sync
+spd_done:
+ blr
+
+check_next_slot:
+ cmpi 0,0,r10,SPD_DIMM1
+ beq spd_read_fail
+ li r10,SPD_DIMM1
+ b do_first_dimm
+spd_read_fail:
+ ori r3,r0,0xdead
+ b err_hung
+spd_fail:
+ li r3,0x0bad
+ sync
+err_hung: /* hang here for debugging */
+ nop
+ nop
+ b err_hung
+
+#endif /* !SDC_HARDCODED_INIT */
diff --git a/board/mpc7448hpc2/config.mk b/board/mpc7448hpc2/config.mk
new file mode 100644
index 0000000..2e58858
--- /dev/null
+++ b/board/mpc7448hpc2/config.mk
@@ -0,0 +1,28 @@
+#
+# Copyright (c) 2005 Freescale Semiconductor, Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+# Flash address
+TEXT_BASE = 0xFF000000
+# RAM address
+#TEXT_BASE = 0x00400000
+
+PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE) -maltivec -mabi=altivec -msoft-float
diff --git a/board/mpc7448hpc2/mpc7448hpc2.c b/board/mpc7448hpc2/mpc7448hpc2.c
new file mode 100644
index 0000000..63c99de
--- /dev/null
+++ b/board/mpc7448hpc2/mpc7448hpc2.c
@@ -0,0 +1,107 @@
+/*
+ * (C) Copyright 2005 Freescale Semiconductor, Inc.
+ *
+ * Roy Zang <tie-fei.zang@freescale.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * modifications for the Tsi108 Emul Board by avb@Tundra
+ */
+
+/*
+ * board support/init functions for the
+ * Freescale MPC7448 HPC2 (High-Performance Computing 2 Platform).
+ */
+
+#include <common.h>
+#include <74xx_7xx.h>
+#if defined(CONFIG_OF_FLAT_TREE)
+#include <ft_build.h>
+extern void ft_cpu_setup (void *blob, bd_t *bd);
+#endif
+
+#undef DEBUG
+
+extern void flush_data_cache (void);
+extern void invalidate_l1_instruction_cache (void);
+extern void tsi108_init_f (void);
+
+int display_mem_map (void);
+
+void after_reloc (ulong dest_addr)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ /*
+ * Jump to the main U-Boot board init code
+ */
+ board_init_r ((gd_t *) gd, dest_addr);
+ /* NOTREACHED */
+}
+
+/*
+ * Check Board Identity:
+ * report board type
+ */
+
+int checkboard (void)
+{
+ int l_type = 0;
+
+ printf ("BOARD: %s\n", CFG_BOARD_NAME);
+ return (l_type);
+}
+
+/*
+ * Read Processor ID:
+ *
+ * report calling processor number
+ */
+
+int read_pid (void)
+{
+ return 0; /* we are on single CPU platform for a while */
+}
+
+long int dram_size (int board_type)
+{
+ return 0x20000000; /* 256M bytes */
+}
+
+long int initdram (int board_type)
+{
+ return dram_size (board_type);
+}
+
+#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP)
+void
+ft_board_setup (void *blob, bd_t *bd)
+{
+ u32 *p;
+ int len;
+
+ ft_cpu_setup (blob, bd);
+
+ p = ft_get_prop (blob, "/memory/reg", &len);
+ if (p != NULL) {
+ *p++ = cpu_to_be32 (bd->bi_memstart);
+ *p = cpu_to_be32 (bd->bi_memsize);
+ }
+}
+#endif
diff --git a/board/mpc7448hpc2/tsi108_init.c b/board/mpc7448hpc2/tsi108_init.c
new file mode 100644
index 0000000..8a7efef
--- /dev/null
+++ b/board/mpc7448hpc2/tsi108_init.c
@@ -0,0 +1,665 @@
+/*****************************************************************************
+ * (C) Copyright 2003; Tundra Semiconductor Corp.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *****************************************************************************/
+
+/*----------------------------------------------------------------------------
+ * FILENAME: tsi108_init.c
+ *
+ * Originator: Alex Bounine
+ *
+ * DESCRIPTION:
+ * Initialization code for the Tundra Tsi108 bridge chip
+ *---------------------------------------------------------------------------*/
+
+#include <common.h>
+#include <74xx_7xx.h>
+#include <config.h>
+#include <version.h>
+#include <asm/processor.h>
+#include <tsi108.h>
+
+extern void mpicInit (int verbose);
+
+/*
+ * Configuration Options
+ */
+
+typedef struct {
+ ulong upper;
+ ulong lower;
+} PB2OCN_LUT_ENTRY;
+
+PB2OCN_LUT_ENTRY pb2ocn_lut1[32] = {
+ /* 0 - 7 */
+ {0x00000000, 0x00000201}, /* PBA=0xE000_0000 -> PCI/X (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xE100_0000 -> PCI/X (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xE200_0000 -> PCI/X (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xE300_0000 -> PCI/X (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xE400_0000 -> PCI/X (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xE500_0000 -> PCI/X (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xE600_0000 -> PCI/X (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xE700_0000 -> PCI/X (Byte-Swap) */
+
+ /* 8 - 15 */
+ {0x00000000, 0x00000201}, /* PBA=0xE800_0000 -> PCI/X (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xE900_0000 -> PCI/X (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xEA00_0000 -> PCI/X (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xEB00_0000 -> PCI/X (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xEC00_0000 -> PCI/X (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xED00_0000 -> PCI/X (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xEE00_0000 -> PCI/X (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xEF00_0000 -> PCI/X (Byte-Swap) */
+
+ /* 16 - 23 */
+ {0x00000000, 0x00000201}, /* PBA=0xF000_0000 -> PCI/X (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xF100_0000 -> PCI/X (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xF200_0000 -> PCI/X (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xF300_0000 -> PCI/X (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xF400_0000 -> PCI/X (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xF500_0000 -> PCI/X (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xF600_0000 -> PCI/X (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xF700_0000 -> PCI/X (Byte-Swap) */
+ /* 24 - 31 */
+ {0x00000000, 0x00000201}, /* PBA=0xF800_0000 -> PCI/X (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xF900_0000 -> PCI/X (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xFA00_0000 -> PCI/X PCI I/O (Byte-Swap) */
+ {0x00000000, 0x00000201}, /* PBA=0xFB00_0000 -> PCI/X PCI Config (Byte-Swap) */
+
+ {0x00000000, 0x02000240}, /* PBA=0xFC00_0000 -> HLP */
+ {0x00000000, 0x01000240}, /* PBA=0xFD00_0000 -> HLP */
+ {0x00000000, 0x03000240}, /* PBA=0xFE00_0000 -> HLP */
+ {0x00000000, 0x00000240} /* PBA=0xFF00_0000 -> HLP : (Translation Enabled + Byte-Swap)*/
+};
+
+#ifdef CFG_CLK_SPREAD
+typedef struct {
+ ulong ctrl0;
+ ulong ctrl1;
+} PLL_CTRL_SET;
+
+/*
+ * Clock Generator SPLL0 initialization values
+ * PLL0 configuration table for various PB_CLKO freq.
+ * Uses pre-calculated values for Fs = 30 kHz, D = 0.5%
+ * Fout depends on required PB_CLKO. Based on Fref = 33 MHz
+ */
+
+static PLL_CTRL_SET pll0_config[8] = {
+ {0x00000000, 0x00000000}, /* 0: bypass */
+ {0x00000000, 0x00000000}, /* 1: reserved */
+ {0x00430044, 0x00000043}, /* 2: CG_PB_CLKO = 183 MHz */
+ {0x005c0044, 0x00000039}, /* 3: CG_PB_CLKO = 100 MHz */
+ {0x005c0044, 0x00000039}, /* 4: CG_PB_CLKO = 133 MHz */
+ {0x004a0044, 0x00000040}, /* 5: CG_PB_CLKO = 167 MHz */
+ {0x005c0044, 0x00000039}, /* 6: CG_PB_CLKO = 200 MHz */
+ {0x004f0044, 0x0000003e} /* 7: CG_PB_CLKO = 233 MHz */
+};
+#endif /* CFG_CLK_SPREAD */
+
+/*
+ * Prosessor Bus Clock (in MHz) defined by CG_PB_SELECT
+ * (based on recommended Tsi108 reference clock 33MHz)
+ */
+static int pb_clk_sel[8] = { 0, 0, 183, 100, 133, 167, 200, 233 };
+
+/*
+ * get_board_bus_clk ()
+ *
+ * returns the bus clock in Hz.
+ */
+unsigned long get_board_bus_clk (void)
+{
+ ulong i;
+
+ /* Detect PB clock freq. */
+ i = in32(CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PWRUP_STATUS);
+ i = (i >> 16) & 0x07; /* Get PB PLL multiplier */
+
+ return pb_clk_sel[i] * 1000000;
+}
+
+/*
+ * board_early_init_f ()
+ *
+ * board-specific initialization executed from flash
+ */
+
+int board_early_init_f (void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+ ulong i;
+
+ gd->mem_clk = 0;
+ i = in32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET +
+ CG_PWRUP_STATUS);
+ i = (i >> 20) & 0x07; /* Get GD PLL multiplier */
+ switch (i) {
+ case 0: /* external clock */
+ printf ("Using external clock\n");
+ break;
+ case 1: /* system clock */
+ gd->mem_clk = gd->bus_clk;
+ break;
+ case 4: /* 133 MHz */
+ case 5: /* 166 MHz */
+ case 6: /* 200 MHz */
+ gd->mem_clk = pb_clk_sel[i] * 1000000;
+ break;
+ default:
+ printf ("Invalid DDR2 clock setting\n");
+ return -1;
+ }
+ printf ("BUS: %d MHz\n", get_board_bus_clk() / 1000000);
+ printf ("MEM: %d MHz\n", gd->mem_clk / 1000000);
+ return 0;
+}
+
+/*
+ * board_early_init_r() - Tsi108 initialization function executed right after
+ * relocation. Contains code that cannot be executed from flash.
+ */
+
+int board_early_init_r (void)
+{
+ ulong temp, i;
+ ulong reg_val;
+ volatile ulong *reg_ptr;
+
+ reg_ptr =
+ (ulong *) (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + 0x900);
+
+ for (i = 0; i < 32; i++) {
+ *reg_ptr++ = 0x00000201; /* SWAP ENABLED */
+ *reg_ptr++ = 0x00;
+ }
+
+ __asm__ __volatile__ ("eieio");
+ __asm__ __volatile__ ("sync");
+
+ /* Setup PB_OCN_BAR2: size 256B + ENable @ 0x0_80000000 */
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR2,
+ 0x80000001);
+ __asm__ __volatile__ ("sync");
+
+ /* Make sure that OCN_BAR2 decoder is set (to allow following immediate
+ * read from SDRAM)
+ */
+
+ temp = in32(CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR2);
+ __asm__ __volatile__ ("sync");
+
+ /*
+ * Remap PB_OCN_BAR1 to accomodate PCI-bus aperture and EPROM into the
+ * processor bus address space. Immediately after reset LUT and address
+ * translation are disabled for this BAR. Now we have to initialize LUT
+ * and switch from the BOOT mode to the normal operation mode.
+ *
+ * The aperture defined by PB_OCN_BAR1 startes at address 0xE0000000
+ * and covers 512MB of address space. To allow larger aperture we also
+ * have to relocate register window of Tsi108
+ *
+ * Initialize LUT (32-entries) prior switching PB_OCN_BAR1 from BOOT
+ * mode.
+ *
+ * initialize pointer to LUT associated with PB_OCN_BAR1
+ */
+ reg_ptr =
+ (ulong *) (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + 0x800);
+
+ for (i = 0; i < 32; i++) {
+ *reg_ptr++ = pb2ocn_lut1[i].lower;
+ *reg_ptr++ = pb2ocn_lut1[i].upper;
+ }
+
+ __asm__ __volatile__ ("sync");
+
+ /* Base addresses for CS0, CS1, CS2, CS3 */
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_ADDR,
+ 0x00000000);
+ __asm__ __volatile__ ("sync");
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_ADDR,
+ 0x00100000);
+ __asm__ __volatile__ ("sync");
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_ADDR,
+ 0x00200000);
+ __asm__ __volatile__ ("sync");
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_ADDR,
+ 0x00300000);
+ __asm__ __volatile__ ("sync");
+
+ /* Masks for HLP banks */
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_MASK,
+ 0xFFF00000);
+ __asm__ __volatile__ ("sync");
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_MASK,
+ 0xFFF00000);
+ __asm__ __volatile__ ("sync");
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_MASK,
+ 0xFFF00000);
+ __asm__ __volatile__ ("sync");
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_MASK,
+ 0xFFF00000);
+ __asm__ __volatile__ ("sync");
+
+ /* Set CTRL0 values for banks */
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_CTRL0,
+ 0x7FFC44C2);
+ __asm__ __volatile__ ("sync");
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_CTRL0,
+ 0x7FFC44C0);
+ __asm__ __volatile__ ("sync");
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_CTRL0,
+ 0x7FFC44C0);
+ __asm__ __volatile__ ("sync");
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_CTRL0,
+ 0x7FFC44C2);
+ __asm__ __volatile__ ("sync");
+
+ /* Set banks to latched mode, enabled, and other default settings */
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_CTRL1,
+ 0x7C0F2000);
+ __asm__ __volatile__ ("sync");
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_CTRL1,
+ 0x7C0F2000);
+ __asm__ __volatile__ ("sync");
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_CTRL1,
+ 0x7C0F2000);
+ __asm__ __volatile__ ("sync");
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_CTRL1,
+ 0x7C0F2000);
+ __asm__ __volatile__ ("sync");
+
+ /*
+ * Set new value for PB_OCN_BAR1: switch from BOOT to LUT mode.
+ * value for PB_OCN_BAR1: (BA-0xE000_0000 + size 512MB + ENable)
+ */
+ out32 (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR1,
+ 0xE0000011);
+ __asm__ __volatile__ ("sync");
+
+ /* Make sure that OCN_BAR2 decoder is set (to allow following
+ * immediate read from SDRAM)
+ */
+
+ temp = in32(CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR1);
+ __asm__ __volatile__ ("sync");
+
+ /*
+ * SRI: At this point we have enabled the HLP banks. That means we can
+ * now read from the NVRAM and initialize the environment variables.
+ * We will over-ride the env_init called in board_init_f
+ * This is really a work-around because, the HLP bank 1
+ * where NVRAM resides is not visible during board_init_f
+ * (lib_ppc/board.c)
+ * Alternatively, we could use the I2C EEPROM at start-up to configure
+ * and enable all HLP banks and not just HLP 0 as is being done for
+ * Taiga Rev. 2.
+ */
+
+ env_init ();
+
+#ifndef DISABLE_PBM
+
+ /*
+ * For IBM processors we have to set Address-Only commands generated
+ * by PBM that are different from ones set after reset.
+ */
+
+ temp = get_cpu_type ();
+
+ if ((CPU_750FX == temp) || (CPU_750GX == temp))
+ out32 (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_MCMD,
+ 0x00009955);
+#endif /* DISABLE_PBM */
+
+#ifdef CONFIG_PCI
+ /*
+ * Initialize PCI/X block
+ */
+
+ /* Map PCI/X Configuration Space (16MB @ 0x0_FE000000) */
+ out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET +
+ PCI_PFAB_BAR0_UPPER, 0);
+ __asm__ __volatile__ ("sync");
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PFAB_BAR0,
+ 0xFB000001);
+ __asm__ __volatile__ ("sync");
+
+ /* Set Bus Number for the attached PCI/X bus (we will use 0 for NB) */
+
+ temp = in32(CFG_TSI108_CSR_BASE +
+ TSI108_PCI_REG_OFFSET + PCI_PCIX_STAT);
+
+ temp &= ~0xFF00; /* Clear the BUS_NUM field */
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PCIX_STAT,
+ temp);
+
+ /* Map PCI/X IO Space (64KB @ 0x0_FD000000) takes one 16MB LUT entry */
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PFAB_IO_UPPER,
+ 0);
+ __asm__ __volatile__ ("sync");
+
+ /* This register is on the PCI side to interpret the address it receives
+ * and maps it as a IO address.
+ */
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PFAB_IO,
+ 0xFA000001);
+ __asm__ __volatile__ ("sync");
+
+ /*
+ * Map PCI/X Memory Space
+ *
+ * Transactions directed from OCM to PCI Memory Space are directed
+ * from PB to PCI
+ * unchanged (as defined by PB_OCN_BAR1,2 and LUT settings).
+ * If address remapping is required the corresponding PCI_PFAB_MEM32
+ * and PCI_PFAB_PFMx register groups have to be configured.
+ *
+ * Map the path from the PCI/X bus into the system memory
+ *
+ * The memory mapped window assotiated with PCI P2O_BAR2 provides
+ * access to the system memory without address remapping.
+ * All system memory is opened for accesses initiated by PCI/X bus
+ * masters.
+ *
+ * Initialize LUT associated with PCI P2O_BAR2
+ *
+ * set pointer to LUT associated with PCI P2O_BAR2
+ */
+
+ reg_ptr =
+ (ulong *) (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + 0x500);
+
+#ifdef DISABLE_PBM
+
+ /* In case when PBM is disabled (no HW supported cache snoopng on PB)
+ * P2O_BAR2 is directly mapped into the system memory without address
+ * translation.
+ */
+
+ reg_val = 0x00000004; /* SDRAM port + NO Addr_Translation */
+
+ for (i = 0; i < 32; i++) {
+ *reg_ptr++ = reg_val; /* P2O_BAR2_LUTx */
+ *reg_ptr++ = 0; /* P2O_BAR2_LUT_UPPERx */
+ }
+
+ /* value for PCI BAR2 (size = 512MB, Enabled, No Addr. Translation) */
+ reg_val = 0x00007500;
+#else
+
+ reg_val = 0x00000002; /* Destination port = PBM */
+
+ for (i = 0; i < 32; i++) {
+ *reg_ptr++ = reg_val; /* P2O_BAR2_LUTx */
+/* P2O_BAR2_LUT_UPPERx : Set data swapping mode for PBM (byte swapping) */
+ *reg_ptr++ = 0x40000000;
+/* offset = 16MB, address translation is enabled to allow byte swapping */
+ reg_val += 0x01000000;
+ }
+
+/* value for PCI BAR2 (size = 512MB, Enabled, Address Translation Enabled) */
+ reg_val = 0x00007100;
+#endif
+
+ __asm__ __volatile__ ("eieio");
+ __asm__ __volatile__ ("sync");
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_PAGE_SIZES,
+ reg_val);
+ __asm__ __volatile__ ("sync");
+
+ /* Set 64-bit PCI bus address for system memory
+ * ( 0 is the best choice for easy mapping)
+ */
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR2,
+ 0x00000000);
+ out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR2_UPPER,
+ 0x00000000);
+ __asm__ __volatile__ ("sync");
+
+#ifndef DISABLE_PBM
+ /*
+ * The memory mapped window assotiated with PCI P2O_BAR3 provides
+ * access to the system memory using SDRAM OCN port and address
+ * translation. This is alternative way to access SDRAM from PCI
+ * required for Tsi108 emulation testing.
+ * All system memory is opened for accesses initiated by
+ * PCI/X bus masters.
+ *
+ * Initialize LUT associated with PCI P2O_BAR3
+ *
+ * set pointer to LUT associated with PCI P2O_BAR3
+ */
+ reg_ptr =
+ (ulong *) (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + 0x600);
+
+ reg_val = 0x00000004; /* Destination port = SDC */
+
+ for (i = 0; i < 32; i++) {
+ *reg_ptr++ = reg_val; /* P2O_BAR3_LUTx */
+
+/* P2O_BAR3_LUT_UPPERx : Set data swapping mode for PBM (byte swapping) */
+ *reg_ptr++ = 0;
+
+/* offset = 16MB, address translation is enabled to allow byte swapping */
+ reg_val += 0x01000000;
+ }
+
+ __asm__ __volatile__ ("eieio");
+ __asm__ __volatile__ ("sync");
+
+ /* Configure PCI P2O_BAR3 (size = 512MB, Enabled) */
+
+ reg_val =
+ in32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET +
+ PCI_P2O_PAGE_SIZES);
+ reg_val &= ~0x00FF;
+ reg_val |= 0x0071;
+ out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_PAGE_SIZES,
+ reg_val);
+ __asm__ __volatile__ ("sync");
+
+ /* Set 64-bit base PCI bus address for window (0x20000000) */
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR3_UPPER,
+ 0x00000000);
+ out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR3,
+ 0x20000000);
+ __asm__ __volatile__ ("sync");
+
+#endif /* !DISABLE_PBM */
+
+#ifdef ENABLE_PCI_CSR_BAR
+ /* open if required access to Tsi108 CSRs from the PCI/X bus */
+ /* enable BAR0 on the PCI/X bus */
+ reg_val = in32(CFG_TSI108_CSR_BASE +
+ TSI108_PCI_REG_OFFSET + PCI_MISC_CSR);
+ reg_val |= 0x02;
+ out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_MISC_CSR,
+ reg_val);
+ __asm__ __volatile__ ("sync");
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR0_UPPER,
+ 0x00000000);
+ out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR0,
+ CFG_TSI108_CSR_BASE);
+ __asm__ __volatile__ ("sync");
+
+#endif
+
+ /*
+ * Finally enable PCI/X Bus Master and Memory Space access
+ */
+
+ reg_val = in32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_CSR);
+ reg_val |= 0x06;
+ out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_CSR, reg_val);
+ __asm__ __volatile__ ("sync");
+
+#endif /* CONFIG_PCI */
+
+ /*
+ * Initialize MPIC outputs (interrupt pins):
+ * Interrupt routing on the Grendel Emul. Board:
+ * PB_INT[0] -> INT (CPU0)
+ * PB_INT[1] -> INT (CPU1)
+ * PB_INT[2] -> MCP (CPU0)
+ * PB_INT[3] -> MCP (CPU1)
+ * Set interrupt controller outputs as Level_Sensitive/Active_Low
+ */
+ out32 (CFG_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(0), 0x02);
+ out32 (CFG_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(1), 0x02);
+ out32 (CFG_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(2), 0x02);
+ out32 (CFG_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(3), 0x02);
+ __asm__ __volatile__ ("sync");
+
+ /*
+ * Ensure that Machine Check exception is enabled
+ * We need it to support PCI Bus probing (configuration reads)
+ */
+
+ reg_val = mfmsr ();
+ mtmsr(reg_val | MSR_ME);
+
+ return 0;
+}
+
+/*
+ * Needed to print out L2 cache info
+ * used in the misc_init_r function
+ */
+
+unsigned long get_l2cr (void)
+{
+ unsigned long l2controlreg;
+ asm volatile ("mfspr %0, 1017":"=r" (l2controlreg):);
+ return l2controlreg;
+}
+
+/*
+ * misc_init_r()
+ *
+ * various things to do after relocation
+ *
+ */
+
+int misc_init_r (void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+#ifdef CFG_CLK_SPREAD /* Initialize Spread-Spectrum Clock generation */
+ ulong i;
+
+ /* Ensure that Spread-Spectrum is disabled */
+ out32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL0, 0);
+ out32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL0, 0);
+
+ /* Initialize PLL1: CG_PCI_CLK , internal OCN_CLK
+ * Uses pre-calculated value for Fout = 800 MHz, Fs = 30 kHz, D = 0.5%
+ */
+
+ out32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL0,
+ 0x002e0044); /* D = 0.25% */
+ out32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL1,
+ 0x00000039); /* BWADJ */
+
+ /* Initialize PLL0: CG_PB_CLKO */
+ /* Detect PB clock freq. */
+ i = in32(CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PWRUP_STATUS);
+ i = (i >> 16) & 0x07; /* Get PB PLL multiplier */
+
+ out32 (CFG_TSI108_CSR_BASE +
+ TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL0, pll0_config[i].ctrl0);
+ out32 (CFG_TSI108_CSR_BASE +
+ TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL1, pll0_config[i].ctrl1);
+
+ /* Wait and set SSEN for both PLL0 and 1 */
+ udelay (1000);
+ out32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL0,
+ 0x802e0044); /* D=0.25% */
+ out32 (CFG_TSI108_CSR_BASE +
+ TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL0,
+ 0x80000000 | pll0_config[i].ctrl0);
+#endif /* CFG_CLK_SPREAD */
+
+#ifdef CFG_L2
+ l2cache_enable ();
+#endif
+ printf ("BUS: %d MHz\n", gd->bus_clk / 1000000);
+ printf ("MEM: %d MHz\n", gd->mem_clk / 1000000);
+
+ /*
+ * All the information needed to print the cache details is avaiblable
+ * at this point i.e. above call to l2cache_enable is the very last
+ * thing done with regards to enabling diabling the cache.
+ * So this seems like a good place to print all this information
+ */
+
+ printf ("CACHE: ");
+ switch (get_cpu_type()) {
+ case CPU_7447A:
+ printf ("L1 Instruction cache - 32KB 8-way");
+ (get_hid0 () & (1 << 15)) ? printf (" ENABLED\n") :
+ printf (" DISABLED\n");
+ printf ("L1 Data cache - 32KB 8-way");
+ (get_hid0 () & (1 << 14)) ? printf (" ENABLED\n") :
+ printf (" DISABLED\n");
+ printf ("Unified L2 cache - 512KB 8-way");
+ (get_l2cr () & (1 << 31)) ? printf (" ENABLED\n") :
+ printf (" DISABLED\n");
+ printf ("\n");
+ break;
+
+ case CPU_7448:
+ printf ("L1 Instruction cache - 32KB 8-way");
+ (get_hid0 () & (1 << 15)) ? printf (" ENABLED\n") :
+ printf (" DISABLED\n");
+ printf ("L1 Data cache - 32KB 8-way");
+ (get_hid0 () & (1 << 14)) ? printf (" ENABLED\n") :
+ printf (" DISABLED\n");
+ printf ("Unified L2 cache - 1MB 8-way");
+ (get_l2cr () & (1 << 31)) ? printf (" ENABLED\n") :
+ printf (" DISABLED\n");
+ break;
+ default:
+ break;
+ }
+ return 0;
+}
diff --git a/board/mpc7448hpc2/u-boot.lds b/board/mpc7448hpc2/u-boot.lds
new file mode 100644
index 0000000..8f24213
--- /dev/null
+++ b/board/mpc7448hpc2/u-boot.lds
@@ -0,0 +1,136 @@
+/*
+ * (C) Copyright 2001
+ * Josh Huber <huber@mclx.com>, Mission Critical Linux, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * u-boot.lds - linker script for U-Boot on mpc7448hpc2 Board.
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+ __DYNAMIC = 0; */
+SECTIONS
+{
+ /* Read-only sections, merged into text segment: */
+ . = + SIZEOF_HEADERS;
+ .interp : { *(.interp) }
+ .hash : { *(.hash) }
+ .dynsym : { *(.dynsym) }
+ .dynstr : { *(.dynstr) }
+ .rel.text : { *(.rel.text) }
+ .rela.text : { *(.rela.text) }
+ .rel.data : { *(.rel.data) }
+ .rela.data : { *(.rela.data) }
+ .rel.rodata : { *(.rel.rodata) }
+ .rela.rodata : { *(.rela.rodata) }
+ .rel.got : { *(.rel.got) }
+ .rela.got : { *(.rela.got) }
+ .rel.ctors : { *(.rel.ctors) }
+ .rela.ctors : { *(.rela.ctors) }
+ .rel.dtors : { *(.rel.dtors) }
+ .rela.dtors : { *(.rela.dtors) }
+ .rel.bss : { *(.rel.bss) }
+ .rela.bss : { *(.rela.bss) }
+ .rel.plt : { *(.rel.plt) }
+ .rela.plt : { *(.rela.plt) }
+ .init : { *(.init) }
+ .plt : { *(.plt) }
+ .text :
+ {
+ cpu/74xx_7xx/start.o (.text)
+
+/* store the environment in a seperate sector in the boot flash */
+/* . = env_offset; */
+/* common/environment.o(.text) */
+
+ *(.text)
+ *(.fixup)
+ *(.got1)
+ }
+ _etext = .;
+ PROVIDE (etext = .);
+ .rodata :
+ {
+ *(.rodata)
+ *(.rodata1)
+ *(.rodata.str1.4)
+ }
+ .fini : { *(.fini) } =0
+ .ctors : { *(.ctors) }
+ .dtors : { *(.dtors) }
+
+ /* Read-write section, merged into data segment: */
+ . = (. + 0x00FF) & 0xFFFFFF00;
+ _erotext = .;
+ PROVIDE (erotext = .);
+ .reloc :
+ {
+ *(.got)
+ _GOT2_TABLE_ = .;
+ *(.got2)
+ _FIXUP_TABLE_ = .;
+ *(.fixup)
+ }
+ __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+ __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+ .data :
+ {
+ *(.data)
+ *(.data1)
+ *(.sdata)
+ *(.sdata2)
+ *(.dynamic)
+ CONSTRUCTORS
+ }
+ _edata = .;
+ PROVIDE (edata = .);
+
+ . = .;
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+ . = .;
+ __start___ex_table = .;
+ __ex_table : { *(__ex_table) }
+ __stop___ex_table = .;
+
+ . = ALIGN(256);
+ __init_begin = .;
+ .text.init : { *(.text.init) }
+ .data.init : { *(.data.init) }
+ . = ALIGN(256);
+ __init_end = .;
+
+ __bss_start = .;
+ .bss :
+ {
+ *(.sbss) *(.scommon)
+ *(.dynbss)
+ *(.bss)
+ *(COMMON)
+ }
+ _end = . ;
+ PROVIDE (end = .);
+}
diff --git a/board/mpc8360emds/config.mk b/board/mpc8360emds/config.mk
index 9ace886..5801a5f 100644
--- a/board/mpc8360emds/config.mk
+++ b/board/mpc8360emds/config.mk
@@ -26,3 +26,8 @@
#
TEXT_BASE = 0xFE000000
+
+#
+# Additional board-specific libraries
+#
+BOARDLIBS = libfdt/libfdt.a
diff --git a/board/mpc8360emds/mpc8360emds.c b/board/mpc8360emds/mpc8360emds.c
index 535884c..deadb5f 100644
--- a/board/mpc8360emds/mpc8360emds.c
+++ b/board/mpc8360emds/mpc8360emds.c
@@ -31,6 +31,10 @@
#if defined(CONFIG_OF_FLAT_TREE)
#include <ft_build.h>
#endif
+#if defined(CONFIG_OF_LIBFDT)
+#include <libfdt.h>
+#include <libfdt_env.h>
+#endif
const qe_iop_conf_t qe_iop_conf_tab[] = {
/* GETH1 */
@@ -658,22 +662,36 @@
" - disables injects\n" " - re-inits memory");
#endif /* if defined(CONFIG_DDR_ECC) && defined(CONFIG_DDR_ECC_CMD) */
-#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP)
+#if (defined(CONFIG_OF_FLAT_TREE) || defined(CONFIG_OF_LIBFDT)) \
+ && defined(CONFIG_OF_BOARD_SETUP)
void
ft_board_setup(void *blob, bd_t *bd)
{
+#if defined(CONFIG_OF_LIBFDT)
+ int nodeoffset;
+ int err;
+ int tmp[2];
+
+ nodeoffset = fdt_path_offset (fdt, "/memory");
+ if (nodeoffset >= 0) {
+ tmp[0] = cpu_to_be32(bd->bi_memstart);
+ tmp[1] = cpu_to_be32(bd->bi_memsize);
+ err = fdt_setprop(fdt, nodeoffset, "reg", tmp, sizeof(tmp));
+ }
+#else
u32 *p;
int len;
-#ifdef CONFIG_PCI
- ft_pci_setup(blob, bd);
-#endif
- ft_cpu_setup(blob, bd);
-
p = ft_get_prop(blob, "/memory/reg", &len);
if (p != NULL) {
*p++ = cpu_to_be32(bd->bi_memstart);
*p = cpu_to_be32(bd->bi_memsize);
}
+#endif
+
+#ifdef CONFIG_PCI
+ ft_pci_setup(blob, bd);
+#endif
+ ft_cpu_setup(blob, bd);
}
#endif
diff --git a/board/mpc8360emds/pci.c b/board/mpc8360emds/pci.c
index 67cd709..158effe 100644
--- a/board/mpc8360emds/pci.c
+++ b/board/mpc8360emds/pci.c
@@ -21,6 +21,10 @@
#if defined(CONFIG_OF_FLAT_TREE)
#include <ft_build.h>
#endif
+#if defined(CONFIG_OF_LIBFDT)
+#include <libfdt.h>
+#include <libfdt_env.h>
+#endif
#include <asm/fsl_i2c.h>
@@ -299,6 +303,22 @@
}
#endif /* CONFIG_PCISLAVE */
+#if defined(CONFIG_OF_LIBFDT)
+void
+ft_pci_setup(void *blob, bd_t *bd)
+{
+ int nodeoffset;
+ int err;
+ int tmp[2];
+
+ nodeoffset = fdt_path_offset (fdt, "/" OF_SOC "/pci@8500");
+ if (nodeoffset >= 0) {
+ tmp[0] = cpu_to_be32(hose[0].first_busno);
+ tmp[1] = cpu_to_be32(hose[0].last_busno);
+ err = fdt_setprop(fdt, nodeoffset, "bus-range", tmp, sizeof(tmp));
+ }
+}
+#endif /* CONFIG_OF_LIBFDT */
#ifdef CONFIG_OF_FLAT_TREE
void
ft_pci_setup(void *blob, bd_t *bd)
diff --git a/board/uc101/uc101.c b/board/uc101/uc101.c
index 7a6b3be..f726513 100644
--- a/board/uc101/uc101.c
+++ b/board/uc101/uc101.c
@@ -221,6 +221,8 @@
int checkboard (void)
{
puts ("Board: MAN UC101\n");
+ /* clear the Display */
+ *(char *)(CFG_DISP_CWORD) = 0x80;
return 0;
}
diff --git a/board/xilinx/ml401/Makefile b/board/xilinx/ml401/Makefile
new file mode 100644
index 0000000..9ab5633
--- /dev/null
+++ b/board/xilinx/ml401/Makefile
@@ -0,0 +1,65 @@
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+ifneq ($(OBJTREE),$(SRCTREE))
+$(shell mkdir -p $(obj)../common)
+$(shell mkdir -p $(obj)../xilinx_enet)
+endif
+
+INCS := -I../common -I../xilinx_enet
+CFLAGS += $(INCS)
+HOST_CFLAGS += $(INCS)
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS = $(BOARD).o \
+ ../xilinx_enet/emac_adapter.o ../xilinx_enet/xemac.o \
+ ../xilinx_enet/xemac_options.o ../xilinx_enet/xemac_polled.o \
+ ../xilinx_enet/xemac_intr.o ../xilinx_enet/xemac_g.o \
+ ../xilinx_enet/xemac_intr_dma.o ../common/xipif_v1_23_b.o \
+ ../common/xbasic_types.o ../common/xdma_channel.o \
+ ../common/xdma_channel_sg.o ../common/xpacket_fifo_v1_00_b.o \
+ ../common/xversion.o \
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $^
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/xilinx/ml401/config.mk b/board/xilinx/ml401/config.mk
new file mode 100644
index 0000000..807f169
--- /dev/null
+++ b/board/xilinx/ml401/config.mk
@@ -0,0 +1,32 @@
+#
+# (C) Copyright 2007 Michal Simek
+#
+# Michal SIMEK <monstr@monstr.eu>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+# CAUTION: This file is automatically generated by libgen.
+# Version: Xilinx EDK 6.3 EDK_Gmm.12.3
+#
+
+TEXT_BASE = 0x12000000
+
+PLATFORM_CPPFLAGS += -mno-xl-soft-mul
+PLATFORM_CPPFLAGS += -mno-xl-soft-div
+PLATFORM_CPPFLAGS += -mxl-barrel-shift
diff --git a/board/xilinx/ml401/ml401.c b/board/xilinx/ml401/ml401.c
new file mode 100644
index 0000000..b48103f
--- /dev/null
+++ b/board/xilinx/ml401/ml401.c
@@ -0,0 +1,49 @@
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal SIMEK <monstr@monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* This is a board specific file. It's OK to include board specific
+ * header files */
+
+#include <common.h>
+#include <config.h>
+
+void do_reset (void)
+{
+#ifdef CFG_GPIO_0
+ *((unsigned long *)(CFG_GPIO_0_ADDR)) =
+ ++(*((unsigned long *)(CFG_GPIO_0_ADDR)));
+#endif
+#ifdef CFG_RESET_ADDRESS
+ puts ("Reseting board\n");
+ asm ("bra r0");
+#endif
+}
+
+int gpio_init (void)
+{
+#ifdef CFG_GPIO_0
+ *((unsigned long *)(CFG_GPIO_0_ADDR)) = 0x0;
+#endif
+ return 0;
+}
diff --git a/include/asm-microblaze/platform.h b/board/xilinx/ml401/u-boot.lds
similarity index 63%
copy from include/asm-microblaze/platform.h
copy to board/xilinx/ml401/u-boot.lds
index 2096cce..cb90854 100644
--- a/include/asm-microblaze/platform.h
+++ b/board/xilinx/ml401/u-boot.lds
@@ -22,8 +22,46 @@
* MA 02111-1307 USA
*/
-#include <config.h>
+OUTPUT_ARCH(microblaze)
+ENTRY(_start)
+
+SECTIONS
+{
+ .text ALIGN(0x4):
+ {
+ __text_start = .;
+ cpu/microblaze/start.o (.text)
+ *(.text)
+ __text_end = .;
+ }
+
+ .rodata ALIGN(0x4):
+ {
+ __rodata_start = .;
+ *(.rodata)
+ __rodata_end = .;
+ }
+
+ .data ALIGN(0x4):
+ {
+ __data_start = .;
+ *(.data)
+ __data_end = .;
+ }
+
+ .u_boot_cmd ALIGN(0x4):
+ {
+ . = .;
+ __u_boot_cmd_start = .;
+ *(.u_boot_cmd)
+ __u_boot_cmd_end = .;
+ }
-#ifdef CONFIG_SUZAKU
-#include <asm/suzaku.h>
-#endif
+ .bss ALIGN(0x4):
+ {
+ __bss_start = .;
+ *(.bss)
+ __bss_end = .;
+ }
+ __end = . ;
+}
diff --git a/board/xilinx/ml401/xparameters.h b/board/xilinx/ml401/xparameters.h
new file mode 100644
index 0000000..18d24f9
--- /dev/null
+++ b/board/xilinx/ml401/xparameters.h
@@ -0,0 +1,67 @@
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal SIMEK <monstr@monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ *
+ * CAUTION: This file is automatically generated by libgen.
+ * Version: Xilinx EDK 6.3 EDK_Gmm.12.3
+ */
+
+/* System Clock Frequency */
+#define XILINX_CLOCK_FREQ 66666667
+
+/* Interrupt controller is intc_0 */
+#define XILINX_INTC_BASEADDR 0xd1000fc0
+#define XILINX_INTC_NUM_INTR_INPUTS 12
+
+/* Timer pheriphery is opb_timer_0 */
+#define XILINX_TIMER_BASEADDR 0xa2000000
+#define XILINX_TIMER_IRQ 0
+
+/* Uart pheriphery is console_uart */
+#define XILINX_UART_BASEADDR 0xa0000000
+#define XILINX_UART_BAUDRATE 115200
+
+/* GPIO is opb_gpio_0*/
+#define XILINX_GPIO_BASEADDR 0x90000000
+
+/* Flash Memory is opb_emc_0 */
+#define XILINX_FLASH_START 0x28000000
+#define XILINX_FLASH_SIZE 0x00800000
+
+/* Main Memory is plb_ddr_0 */
+#define XILINX_RAM_START 0x10000000
+#define XILINX_RAM_SIZE 0x10000000
+
+/* Sysace Controller is opb_sysace_0 */
+#define XILINX_SYSACE_BASEADDR 0xCF000000
+#define XILINX_SYSACE_HIGHADDR 0xCF0001FF
+#define XILINX_SYSACE_MEM_WIDTH 16
+
+/* Ethernet controller is opb_ethernet_0 */
+#define XPAR_XEMAC_NUM_INSTANCES 1
+#define XPAR_OPB_ETHERNET_0_DEVICE_ID 0
+#define XPAR_OPB_ETHERNET_0_BASEADDR 0x60000000
+#define XPAR_OPB_ETHERNET_0_HIGHADDR 0x60003FFF
+#define XPAR_OPB_ETHERNET_0_DMA_PRESENT 1
+#define XPAR_OPB_ETHERNET_0_ERR_COUNT_EXIST 1
+#define XPAR_OPB_ETHERNET_0_MII_EXIST 1
diff --git a/board/xilinx/xilinx_enet/emac_adapter.c b/board/xilinx/xilinx_enet/emac_adapter.c
index f159cb6..d340303 100644
--- a/board/xilinx/xilinx_enet/emac_adapter.c
+++ b/board/xilinx/xilinx_enet/emac_adapter.c
@@ -147,7 +147,11 @@
RecvFrameLength = PKTSIZE;
Result = XEmac_PollRecv(&Emac, (u8 *) etherrxbuff, &RecvFrameLength);
if (Result == XST_SUCCESS) {
+#ifndef CONFIG_EMACLITE
NetReceive((uchar *)etherrxbuff, RecvFrameLength);
+#else
+ NetReceive(etherrxbuff, RecvFrameLength);
+#endif
return (1);
} else {
return (0);
diff --git a/board/xilinx/xupv2p/Makefile b/board/xilinx/xupv2p/Makefile
new file mode 100644
index 0000000..9ab5633
--- /dev/null
+++ b/board/xilinx/xupv2p/Makefile
@@ -0,0 +1,65 @@
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+ifneq ($(OBJTREE),$(SRCTREE))
+$(shell mkdir -p $(obj)../common)
+$(shell mkdir -p $(obj)../xilinx_enet)
+endif
+
+INCS := -I../common -I../xilinx_enet
+CFLAGS += $(INCS)
+HOST_CFLAGS += $(INCS)
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS = $(BOARD).o \
+ ../xilinx_enet/emac_adapter.o ../xilinx_enet/xemac.o \
+ ../xilinx_enet/xemac_options.o ../xilinx_enet/xemac_polled.o \
+ ../xilinx_enet/xemac_intr.o ../xilinx_enet/xemac_g.o \
+ ../xilinx_enet/xemac_intr_dma.o ../common/xipif_v1_23_b.o \
+ ../common/xbasic_types.o ../common/xdma_channel.o \
+ ../common/xdma_channel_sg.o ../common/xpacket_fifo_v1_00_b.o \
+ ../common/xversion.o \
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $^
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/xilinx/xupv2p/config.mk b/board/xilinx/xupv2p/config.mk
new file mode 100644
index 0000000..c07b0b3
--- /dev/null
+++ b/board/xilinx/xupv2p/config.mk
@@ -0,0 +1,32 @@
+#
+# (C) Copyright 2007 Michal Simek
+#
+# Michal SIMEK <monstr@monstr.eu>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+# CAUTION: This file is automatically generated by libgen.
+# Version: Xilinx EDK 8.2.02 EDK_Im_Sp2.4
+#
+
+TEXT_BASE = 0x38000000
+
+PLATFORM_CPPFLAGS += -mno-xl-soft-mul
+PLATFORM_CPPFLAGS += -mno-xl-soft-div
+PLATFORM_CPPFLAGS += -mxl-barrel-shift
diff --git a/include/asm-microblaze/platform.h b/board/xilinx/xupv2p/u-boot.lds
similarity index 63%
copy from include/asm-microblaze/platform.h
copy to board/xilinx/xupv2p/u-boot.lds
index 2096cce..cb90854 100644
--- a/include/asm-microblaze/platform.h
+++ b/board/xilinx/xupv2p/u-boot.lds
@@ -22,8 +22,46 @@
* MA 02111-1307 USA
*/
-#include <config.h>
+OUTPUT_ARCH(microblaze)
+ENTRY(_start)
+
+SECTIONS
+{
+ .text ALIGN(0x4):
+ {
+ __text_start = .;
+ cpu/microblaze/start.o (.text)
+ *(.text)
+ __text_end = .;
+ }
+
+ .rodata ALIGN(0x4):
+ {
+ __rodata_start = .;
+ *(.rodata)
+ __rodata_end = .;
+ }
+
+ .data ALIGN(0x4):
+ {
+ __data_start = .;
+ *(.data)
+ __data_end = .;
+ }
+
+ .u_boot_cmd ALIGN(0x4):
+ {
+ . = .;
+ __u_boot_cmd_start = .;
+ *(.u_boot_cmd)
+ __u_boot_cmd_end = .;
+ }
-#ifdef CONFIG_SUZAKU
-#include <asm/suzaku.h>
-#endif
+ .bss ALIGN(0x4):
+ {
+ __bss_start = .;
+ *(.bss)
+ __bss_end = .;
+ }
+ __end = . ;
+}
diff --git a/board/xilinx/xupv2p/xparameters.h b/board/xilinx/xupv2p/xparameters.h
new file mode 100644
index 0000000..a96c693
--- /dev/null
+++ b/board/xilinx/xupv2p/xparameters.h
@@ -0,0 +1,64 @@
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal SIMEK <monstr@monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * CAUTION: This file is automatically generated by libgen.
+ * Version: Xilinx EDK 8.2.02 EDK_Im_Sp2.4
+ */
+
+/* System Clock Frequency */
+#define XILINX_CLOCK_FREQ 100000000
+
+/* Interrupt controller is opb_intc_0 */
+#define XILINX_INTC_BASEADDR 0x41200000
+#define XILINX_INTC_NUM_INTR_INPUTS 11
+
+/* Timer pheriphery is opb_timer_1 */
+#define XILINX_TIMER_BASEADDR 0x41c00000
+#define XILINX_TIMER_IRQ 1
+
+/* Uart pheriphery is RS232_Uart_1 */
+#define XILINX_UART_BASEADDR 0x40600000
+#define XILINX_UART_BAUDRATE 115200
+
+/* GPIO is LEDs_4Bit*/
+#define XILINX_GPIO_BASEADDR 0x40000000
+
+/* FLASH doesn't exist none */
+
+/* Main Memory is DDR_256MB_32MX64_rank1_row13_col10_cl2_5 */
+#define XILINX_RAM_START 0x30000000
+#define XILINX_RAM_SIZE 0x10000000
+
+/* Sysace Controller is SysACE_CompactFlash */
+#define XILINX_SYSACE_BASEADDR 0x41800000
+#define XILINX_SYSACE_HIGHADDR 0x4180ffff
+#define XILINX_SYSACE_MEM_WIDTH 16
+
+/* Ethernet controller is Ethernet_MAC */
+#define XPAR_XEMAC_NUM_INSTANCES 1
+#define XPAR_OPB_ETHERNET_0_DEVICE_ID 0
+#define XPAR_OPB_ETHERNET_0_BASEADDR 0x40c00000
+#define XPAR_OPB_ETHERNET_0_HIGHADDR 0x40c0ffff
+#define XPAR_OPB_ETHERNET_0_DMA_PRESENT 1
+#define XPAR_OPB_ETHERNET_0_ERR_COUNT_EXIST 1
+#define XPAR_OPB_ETHERNET_0_MII_EXIST 1
diff --git a/board/xilinx/xupv2p/xupv2p.c b/board/xilinx/xupv2p/xupv2p.c
new file mode 100644
index 0000000..b48103f
--- /dev/null
+++ b/board/xilinx/xupv2p/xupv2p.c
@@ -0,0 +1,49 @@
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal SIMEK <monstr@monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* This is a board specific file. It's OK to include board specific
+ * header files */
+
+#include <common.h>
+#include <config.h>
+
+void do_reset (void)
+{
+#ifdef CFG_GPIO_0
+ *((unsigned long *)(CFG_GPIO_0_ADDR)) =
+ ++(*((unsigned long *)(CFG_GPIO_0_ADDR)));
+#endif
+#ifdef CFG_RESET_ADDRESS
+ puts ("Reseting board\n");
+ asm ("bra r0");
+#endif
+}
+
+int gpio_init (void)
+{
+#ifdef CFG_GPIO_0
+ *((unsigned long *)(CFG_GPIO_0_ADDR)) = 0x0;
+#endif
+ return 0;
+}
diff --git a/common/Makefile b/common/Makefile
index 6f81c4a..74a6af2 100644
--- a/common/Makefile
+++ b/common/Makefile
@@ -32,7 +32,7 @@
cmd_cache.o cmd_console.o \
cmd_date.o cmd_dcr.o cmd_diag.o cmd_display.o cmd_doc.o cmd_dtt.o \
cmd_eeprom.o cmd_elf.o cmd_ext2.o \
- cmd_fat.o cmd_fdc.o cmd_fdos.o cmd_flash.o cmd_fpga.o \
+ cmd_fat.o cmd_fdc.o cmd_fdt.o cmd_fdos.o cmd_flash.o cmd_fpga.o \
cmd_i2c.o cmd_ide.o cmd_immap.o cmd_itest.o cmd_jffs2.o \
cmd_load.o cmd_log.o \
cmd_mem.o cmd_mii.o cmd_misc.o cmd_mmc.o \
diff --git a/common/cmd_bdinfo.c b/common/cmd_bdinfo.c
index 70de795..d97c09e 100644
--- a/common/cmd_bdinfo.c
+++ b/common/cmd_bdinfo.c
@@ -180,6 +180,32 @@
return 0;
}
+#elif defined(CONFIG_MICROBLAZE) /* ! PPC, which leaves Microblaze */
+
+int do_bdinfo ( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+ int i;
+ bd_t *bd = gd->bd;
+ print_num ("mem start ", (ulong)bd->bi_memstart);
+ print_num ("mem size ", (ulong)bd->bi_memsize);
+ print_num ("flash start ", (ulong)bd->bi_flashstart);
+ print_num ("flash size ", (ulong)bd->bi_flashsize);
+ print_num ("flash offset ", (ulong)bd->bi_flashoffset);
+#if defined(CFG_SRAM_BASE)
+ print_num ("sram start ", (ulong)bd->bi_sramstart);
+ print_num ("sram size ", (ulong)bd->bi_sramsize);
+#endif
+#if defined(CFG_CMD_NET)
+ puts ("ethaddr =");
+ for (i=0; i<6; ++i) {
+ printf ("%c%02X", i ? ':' : ' ', bd->bi_enetaddr[i]);
+ }
+ puts ("\nip_addr = ");
+ print_IPaddr (bd->bi_ip_addr);
+#endif
+ printf ("\nbaudrate = %d bps\n", (ulong)bd->bi_baudrate);
+ return 0;
+}
#else /* ! PPC, which leaves MIPS */
diff --git a/common/cmd_bootm.c b/common/cmd_bootm.c
index c0ed076..2721216b 100644
--- a/common/cmd_bootm.c
+++ b/common/cmd_bootm.c
@@ -34,7 +34,11 @@
#include <environment.h>
#include <asm/byteorder.h>
-#ifdef CONFIG_OF_FLAT_TREE
+#if defined(CONFIG_OF_LIBFDT)
+#include <fdt.h>
+#include <libfdt.h>
+#endif
+#if defined(CONFIG_OF_FLAT_TREE)
#include <ft_build.h>
#endif
@@ -467,7 +471,7 @@
"[addr [arg ...]]\n - boot application image stored in memory\n"
"\tpassing arguments 'arg ...'; when booting a Linux kernel,\n"
"\t'arg' can be the address of an initrd image\n"
-#ifdef CONFIG_OF_FLAT_TREE
+#if defined(CONFIG_OF_FLAT_TREE) || defined(CONFIG_OF_LIBFDT)
"\tWhen booting a Linux kernel which requires a flat device-tree\n"
"\ta third argument is required which is the address of the of the\n"
"\tdevice-tree blob. To boot that kernel without an initrd image,\n"
@@ -529,7 +533,7 @@
bd_t *kbd;
void (*kernel)(bd_t *, ulong, ulong, ulong, ulong);
image_header_t *hdr = &header;
-#ifdef CONFIG_OF_FLAT_TREE
+#if defined(CONFIG_OF_FLAT_TREE) || defined(CONFIG_OF_LIBFDT)
char *of_flat_tree = NULL;
ulong of_data = 0;
#endif
@@ -622,7 +626,7 @@
* Check if there is an initrd image
*/
-#ifdef CONFIG_OF_FLAT_TREE
+#if defined(CONFIG_OF_FLAT_TREE) || defined(CONFIG_OF_LIBFDT)
/* Look for a '-' which indicates to ignore the ramdisk argument */
if (argc >= 3 && strcmp(argv[2], "-") == 0) {
debug ("Skipping initrd\n");
@@ -739,12 +743,15 @@
len = data = 0;
}
-#ifdef CONFIG_OF_FLAT_TREE
+#if defined(CONFIG_OF_FLAT_TREE) || defined(CONFIG_OF_LIBFDT)
if(argc > 3) {
of_flat_tree = (char *) simple_strtoul(argv[3], NULL, 16);
hdr = (image_header_t *)of_flat_tree;
-
- if (*(ulong *)of_flat_tree == OF_DT_HEADER) {
+#if defined(CONFIG_OF_LIBFDT)
+ if (be32_to_cpu(fdt_magic(of_flat_tree)) == FDT_MAGIC) {
+#else
+ if (*(ulong *)of_flat_tree == OF_DT_HEADER) {
+#endif
#ifndef CFG_NO_FLASH
if (addr2info((ulong)of_flat_tree) != NULL)
of_data = (ulong)of_flat_tree;
@@ -787,7 +794,11 @@
printf("ERROR: uImage is not uncompressed\n");
return;
}
+#if defined(CONFIG_OF_LIBFDT)
+ if (be32_to_cpu(fdt_magic(of_flat_tree + sizeof(image_header_t))) != FDT_MAGIC) {
+#else
if (*((ulong *)(of_flat_tree + sizeof(image_header_t))) != OF_DT_HEADER) {
+#endif
printf ("ERROR: uImage data is not a flat device tree\n");
return;
}
@@ -824,12 +835,20 @@
of_data += 4 - tail;
}
+#if defined(CONFIG_OF_LIBFDT)
+ if (be32_to_cpu(fdt_magic(of_data)) != FDT_MAGIC) {
+#else
if (((struct boot_param_header *)of_data)->magic != OF_DT_HEADER) {
+#endif
printf ("ERROR: image is not a flat device tree\n");
return;
}
+#if defined(CONFIG_OF_LIBFDT)
+ if (be32_to_cpu(fdt_totalsize(of_data)) != ntohl(len_ptr[2])) {
+#else
if (((struct boot_param_header *)of_data)->totalsize != ntohl(len_ptr[2])) {
+#endif
printf ("ERROR: flat device tree size does not agree with image\n");
return;
}
@@ -913,9 +932,33 @@
unlock_ram_in_cache();
#endif
-#ifdef CONFIG_OF_FLAT_TREE
+#if defined(CONFIG_OF_LIBFDT)
/* move of_flat_tree if needed */
if (of_data) {
+ int err;
+ ulong of_start, of_len;
+ of_len = be32_to_cpu(fdt_totalsize(of_data));
+ /* provide extra 8k pad */
+ if (initrd_start)
+ of_start = initrd_start - of_len - 8192;
+ else
+ of_start = (ulong)kbd - of_len - 8192;
+ of_start &= ~(4096 - 1); /* align on page */
+ debug ("## device tree at 0x%08lX ... 0x%08lX (len=%ld=0x%lX)\n",
+ of_data, of_data + of_len - 1, of_len, of_len);
+
+
+ printf (" Loading Device Tree to %08lx, end %08lx ... ",
+ of_start, of_start + of_len - 1);
+ err = fdt_open_into(of_start, of_data, of_len);
+ if (err != 0) {
+ printf ("libfdt: %s\n", fdt_strerror(err));
+ }
+ }
+#endif
+#if defined(CONFIG_OF_FLAT_TREE)
+ /* move of_flat_tree if needed */
+ if (of_data) {
ulong of_start, of_len;
of_len = ((struct boot_param_header *)of_data)->totalsize;
/* provide extra 8k pad */
@@ -942,13 +985,13 @@
* r6: Start of command line string
* r7: End of command line string
*/
-#ifdef CONFIG_OF_FLAT_TREE
+#if defined(CONFIG_OF_FLAT_TREE) || defined(CONFIG_OF_LIBFDT)
if (!of_flat_tree) /* no device tree; boot old style */
#endif
(*kernel) (kbd, initrd_start, initrd_end, cmd_start, cmd_end);
/* does not return */
-#ifdef CONFIG_OF_FLAT_TREE
+#if defined(CONFIG_OF_FLAT_TREE) || defined(CONFIG_OF_LIBFDT)
/*
* Linux Kernel Parameters (passing device tree):
* r3: ptr to OF flat tree, followed by the board info data
@@ -957,8 +1000,10 @@
* r6: NULL
* r7: NULL
*/
+#if defined(CONFIG_OF_FLAT_TREE)
ft_setup(of_flat_tree, kbd, initrd_start, initrd_end);
/* ft_dump_blob(of_flat_tree); */
+#endif
(*kernel) ((bd_t *)of_flat_tree, (ulong)kernel, 0, 0, 0);
#endif
diff --git a/common/cmd_fdt.c b/common/cmd_fdt.c
new file mode 100644
index 0000000..968bade
--- /dev/null
+++ b/common/cmd_fdt.c
@@ -0,0 +1,874 @@
+/*
+ * (C) Copyright 2007
+ * Gerald Van Baren, Custom IDEAS, vanbaren@cideas.com
+ * Based on code written by:
+ * Pantelis Antoniou <pantelis.antoniou@gmail.com> and
+ * Matthew McClintock <msm@freescale.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <linux/ctype.h>
+#include <linux/types.h>
+
+#ifdef CONFIG_OF_LIBFDT
+#include <asm/global_data.h>
+#include <fdt.h>
+#include <libfdt.h>
+
+#define MAX_LEVEL 32 /* how deeply nested we will go */
+#define SCRATCHPAD 1024 /* bytes of scratchpad memory */
+
+/*
+ * Global data (for the gd->bd)
+ */
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Scratchpad memory.
+ */
+static char data[SCRATCHPAD];
+
+
+/*
+ * Function prototypes/declarations.
+ */
+static int fdt_valid(void);
+static void print_data(const void *data, int len);
+static int fdt_chosen(void *fdt, ulong initrd_start, ulong initrd_end);
+static int fdt_env(void *fdt);
+static int fdt_bd_t(void *fdt);
+
+
+/*
+ * Flattened Device Tree command, see the help for parameter definitions.
+ */
+int do_fdt (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
+{
+ char op;
+
+ if (argc < 2) {
+ printf ("Usage:\n%s\n", cmdtp->usage);
+ return 1;
+ }
+
+ /*
+ * Figure out which subcommand was given
+ */
+ op = argv[1][0];
+ /********************************************************************
+ * Set the address of the fdt
+ ********************************************************************/
+ if (op == 'a') {
+ /*
+ * Set the address [and length] of the fdt.
+ */
+ fdt = (struct fdt_header *)simple_strtoul(argv[2], NULL, 16);
+
+ if (!fdt_valid()) {
+ return 1;
+ }
+
+ if (argc >= 4) {
+ int len;
+ int err;
+ /*
+ * Optional new length
+ */
+ len = simple_strtoul(argv[3], NULL, 16);
+ if (len < fdt_totalsize(fdt)) {
+ printf ("New length %d < existing length %d, ignoring.\n",
+ len, fdt_totalsize(fdt));
+ } else {
+ /*
+ * Open in place with a new length.
+ */
+ err = fdt_open_into(fdt, fdt, len);
+ if (err != 0) {
+ printf ("libfdt: %s\n", fdt_strerror(err));
+ }
+ }
+ }
+
+ /********************************************************************
+ * Move the fdt
+ ********************************************************************/
+ } else if (op == 'm') {
+ struct fdt_header *newaddr;
+ int len;
+ int err;
+
+ if (argc != 5) {
+ printf ("Usage:\n%s\n", cmdtp->usage);
+ return 1;
+ }
+
+ /*
+ * Set the address and length of the fdt.
+ */
+ fdt = (struct fdt_header *)simple_strtoul(argv[2], NULL, 16);
+ if (!fdt_valid()) {
+ return 1;
+ }
+
+ newaddr = (struct fdt_header *)simple_strtoul(argv[3], NULL, 16);
+ len = simple_strtoul(argv[4], NULL, 16);
+ if (len < fdt_totalsize(fdt)) {
+ printf ("New length %d < existing length %d, aborting.\n",
+ len, fdt_totalsize(fdt));
+ return 1;
+ }
+
+ /*
+ * Copy to the new location.
+ */
+ err = fdt_open_into(fdt, newaddr, len);
+ if (err != 0) {
+ printf ("libfdt: %s\n", fdt_strerror(err));
+ return 1;
+ }
+ fdt = newaddr;
+
+ /********************************************************************
+ * Set the value of a node in the fdt.
+ ********************************************************************/
+ } else if (op == 's') {
+ char *pathp; /* path */
+ char *prop; /* property */
+ struct fdt_property *nodep; /* node struct pointer */
+ char *newval; /* value from the user (as a string) */
+ char *vp; /* temporary value pointer */
+ char *cp; /* temporary char pointer */
+ int nodeoffset; /* node offset from libfdt */
+ int len; /* new length of the property */
+ int oldlen; /* original length of the property */
+ unsigned long tmp; /* holds converted values */
+ int ret; /* return value */
+
+ /*
+ * Parameters: Node path, property, value.
+ */
+ if (argc < 5) {
+ printf ("Usage:\n%s\n", cmdtp->usage);
+ return 1;
+ }
+
+ pathp = argv[2];
+ prop = argv[3];
+ newval = argv[4];
+
+ if (strcmp(pathp, "/") == 0) {
+ nodeoffset = 0;
+ } else {
+ nodeoffset = fdt_path_offset (fdt, pathp);
+ if (nodeoffset < 0) {
+ /*
+ * Not found or something else bad happened.
+ */
+ printf ("libfdt: %s\n", fdt_strerror(nodeoffset));
+ return 1;
+ }
+ }
+ nodep = fdt_getprop (fdt, nodeoffset, prop, &oldlen);
+ if (oldlen < 0) {
+ printf ("libfdt %s\n", fdt_strerror(oldlen));
+ return 1;
+ } else if (oldlen == 0) {
+ /*
+ * The specified property has no value
+ */
+ printf("%s has no value, cannot set one (yet).\n", prop);
+ return 1;
+ } else {
+ /*
+ * Convert the new property
+ */
+ vp = data;
+ if (*newval == '<') {
+ /*
+ * Bigger values than bytes.
+ */
+ len = 0;
+ newval++;
+ while ((*newval != '>') && (*newval != '\0')) {
+ cp = newval;
+ tmp = simple_strtoul(cp, &newval, 16);
+ if ((newval - cp) <= 2) {
+ *vp = tmp & 0xFF;
+ vp += 1;
+ len += 1;
+ } else if ((newval - cp) <= 4) {
+ *(uint16_t *)vp = __cpu_to_be16(tmp);
+ vp += 2;
+ len += 2;
+ } else if ((newval - cp) <= 8) {
+ *(uint32_t *)vp = __cpu_to_be32(tmp);
+ vp += 4;
+ len += 4;
+ } else {
+ printf("Sorry, I could not convert \"%s\"\n", cp);
+ return 1;
+ }
+ while (*newval == ' ')
+ newval++;
+ }
+ if (*newval != '>') {
+ printf("Unexpected character '%c'\n", *newval);
+ return 1;
+ }
+ } else if (*newval == '[') {
+ /*
+ * Byte stream. Convert the values.
+ */
+ len = 0;
+ newval++;
+ while ((*newval != ']') && (*newval != '\0')) {
+ tmp = simple_strtoul(newval, &newval, 16);
+ *vp++ = tmp & 0xFF;
+ len++;
+ while (*newval == ' ')
+ newval++;
+ }
+ if (*newval != ']') {
+ printf("Unexpected character '%c'\n", *newval);
+ return 1;
+ }
+ } else {
+ /*
+ * Assume it is a string. Copy it into our data area for
+ * convenience (including the terminating '\0').
+ */
+ len = strlen(newval) + 1;
+ strcpy(data, newval);
+ }
+
+ ret = fdt_setprop(fdt, nodeoffset, prop, data, len);
+ if (ret < 0) {
+ printf ("libfdt %s\n", fdt_strerror(ret));
+ return 1;
+ }
+ }
+
+ /********************************************************************
+ * Print (recursive) / List (single level)
+ ********************************************************************/
+ } else if ((op == 'p') || (op == 'l')) {
+ /*
+ * Recursively print (a portion of) the fdt.
+ */
+ static int offstack[MAX_LEVEL];
+ static char tabs[MAX_LEVEL+1] = "\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t";
+ int depth = MAX_LEVEL; /* how deep to print */
+ char *pathp; /* path */
+ char *prop; /* property */
+ void *nodep; /* property node pointer */
+ int nodeoffset; /* node offset from libfdt */
+ int nextoffset; /* next node offset from libfdt */
+ uint32_t tag; /* tag */
+ int len; /* length of the property */
+ int level = 0; /* keep track of nesting level */
+
+ /*
+ * list is an alias for print, but limited to 1 level
+ */
+ if (op == 'l') {
+ depth = 1;
+ }
+
+ /*
+ * Get the starting path. The root node is an oddball,
+ * the offset is zero and has no name.
+ */
+ pathp = argv[2];
+ if (argc > 3)
+ prop = argv[3];
+ else
+ prop = NULL;
+
+ if (strcmp(pathp, "/") == 0) {
+ nodeoffset = 0;
+ printf("/");
+ } else {
+ nodeoffset = fdt_path_offset (fdt, pathp);
+ if (nodeoffset < 0) {
+ /*
+ * Not found or something else bad happened.
+ */
+ printf ("libfdt %s\n", fdt_strerror(nodeoffset));
+ return 1;
+ }
+ }
+ /*
+ * The user passed in a property as well as node path. Print only
+ * the given property and then return.
+ */
+ if (prop) {
+ nodep = fdt_getprop (fdt, nodeoffset, prop, &len);
+ if (len == 0) {
+ printf("%s %s\n", pathp, prop); /* no property value */
+ return 0;
+ } else if (len > 0) {
+ printf("%s=", prop);
+ print_data (nodep, len);
+ printf("\n");
+ return 0;
+ } else {
+ printf ("libfdt %s\n", fdt_strerror(len));
+ return 1;
+ }
+ }
+
+ /*
+ * The user passed in a node path and no property, print the node
+ * and all subnodes.
+ */
+ offstack[0] = nodeoffset;
+
+ while(level >= 0) {
+ tag = fdt_next_tag(fdt, nodeoffset, &nextoffset, &pathp);
+ switch(tag) {
+ case FDT_BEGIN_NODE:
+ if(level <= depth)
+ printf("%s%s {\n", &tabs[MAX_LEVEL - level], pathp);
+ level++;
+ offstack[level] = nodeoffset;
+ if (level >= MAX_LEVEL) {
+ printf("Aaaiii <splat> nested too deep.\n");
+ return 1;
+ }
+ break;
+ case FDT_END_NODE:
+ level--;
+ if(level <= depth)
+ printf("%s};\n", &tabs[MAX_LEVEL - level]);
+ if (level == 0) {
+ level = -1; /* exit the loop */
+ }
+ break;
+ case FDT_PROP:
+ nodep = fdt_getprop (fdt, offstack[level], pathp, &len);
+ if (len < 0) {
+ printf ("libfdt %s\n", fdt_strerror(len));
+ return 1;
+ } else if (len == 0) {
+ /* the property has no value */
+ if(level <= depth)
+ printf("%s%s;\n", &tabs[MAX_LEVEL - level], pathp);
+ } else {
+ if(level <= depth) {
+ printf("%s%s=", &tabs[MAX_LEVEL - level], pathp);
+ print_data (nodep, len);
+ printf(";\n");
+ }
+ }
+ break;
+ case FDT_NOP:
+ break;
+ case FDT_END:
+ return 1;
+ default:
+ if(level <= depth)
+ printf("Unknown tag 0x%08X\n", tag);
+ return 1;
+ }
+ nodeoffset = nextoffset;
+ }
+
+ /********************************************************************
+ * Remove a property/node
+ ********************************************************************/
+ } else if (op == 'r') {
+ int nodeoffset; /* node offset from libfdt */
+ int err;
+
+ /*
+ * Get the path. The root node is an oddball, the offset
+ * is zero and has no name.
+ */
+ if (strcmp(argv[2], "/") == 0) {
+ nodeoffset = 0;
+ } else {
+ nodeoffset = fdt_path_offset (fdt, argv[2]);
+ if (nodeoffset < 0) {
+ /*
+ * Not found or something else bad happened.
+ */
+ printf ("libfdt %s\n", fdt_strerror(nodeoffset));
+ return 1;
+ }
+ }
+ /*
+ * Do the delete. A fourth parameter means delete a property,
+ * otherwise delete the node.
+ */
+ if (argc > 3) {
+ err = fdt_delprop(fdt, nodeoffset, argv[3]);
+ if (err < 0) {
+ printf("fdt_delprop libfdt: %s\n", fdt_strerror(err));
+ return err;
+ }
+ } else {
+ err = fdt_del_node(fdt, nodeoffset);
+ if (err < 0) {
+ printf("fdt_del_node libfdt: %s\n", fdt_strerror(err));
+ return err;
+ }
+ }
+
+ /********************************************************************
+ * Create a chosen node
+ ********************************************************************/
+ } else if (op == 'c') {
+ fdt_chosen(fdt, 0, 0);
+
+ /********************************************************************
+ * Create a u-boot-env node
+ ********************************************************************/
+ } else if (op == 'e') {
+ fdt_env(fdt);
+
+ /********************************************************************
+ * Create a bd_t node
+ ********************************************************************/
+ } else if (op == 'b') {
+ fdt_bd_t(fdt);
+
+ /********************************************************************
+ * Unrecognized command
+ ********************************************************************/
+ } else {
+ printf ("Usage:\n%s\n", cmdtp->usage);
+ return 1;
+ }
+
+ return 0;
+}
+
+/********************************************************************/
+
+static int fdt_valid(void)
+{
+ if (fdt == NULL) {
+ printf ("The address of the fdt is invalid.\n");
+ return 0;
+ }
+ if (!fdt || (fdt_magic(fdt) != FDT_MAGIC)) {
+ fdt = NULL;
+ printf ("Unrecognized fdt: bad magic\n");
+ return 0;
+ }
+ if (fdt_version(fdt) < FDT_FIRST_SUPPORTED_VERSION) {
+ printf ("Unsupported fdt version: $d < %d\n",
+ FDT_FIRST_SUPPORTED_VERSION, fdt_version(fdt));
+ fdt = NULL;
+ return 0;
+ }
+ if (fdt_last_comp_version(fdt) > FDT_LAST_SUPPORTED_VERSION) {
+ printf ("Unsupported fdt version: $d > %d\n",
+ fdt_version(fdt), FDT_LAST_SUPPORTED_VERSION);
+ fdt = NULL;
+ return 0;
+ }
+ return 1;
+}
+
+/********************************************************************/
+
+/*
+ * OF flat tree handling
+ * Written by: Pantelis Antoniou <pantelis.antoniou@gmail.com>
+ * Updated by: Matthew McClintock <msm@freescale.com>
+ * Converted to libfdt by: Gerald Van Baren <vanbaren@cideas.com>
+ */
+
+static int is_printable_string(const void *data, int len)
+{
+ const char *s = data;
+
+ /* zero length is not */
+ if (len == 0)
+ return 0;
+
+ /* must terminate with zero */
+ if (s[len - 1] != '\0')
+ return 0;
+
+ /* printable or a null byte (concatenated strings) */
+ while (((*s == '\0') || isprint(*s)) && (len > 0)) {
+ /*
+ * If we see a null, there are three possibilities:
+ * 1) If len == 1, it is the end of the string, printable
+ * 2) Next character also a null, not printable.
+ * 3) Next character not a null, continue to check.
+ */
+ if (s[0] == '\0') {
+ if (len == 1)
+ return 1;
+ if (s[1] == '\0')
+ return 0;
+ }
+ s++;
+ len--;
+ }
+
+ /* Not the null termination, or not done yet: not printable */
+ if (*s != '\0' || (len != 0))
+ return 0;
+
+ return 1;
+}
+
+static void print_data(const void *data, int len)
+{
+ int j;
+ const u8 *s;
+
+ /* no data, don't print */
+ if (len == 0)
+ return;
+
+ /*
+ * It is a string, but it may have multiple strings (embedded '\0's).
+ */
+ if (is_printable_string(data, len)) {
+ puts("\"");
+ j = 0;
+ while (j < len) {
+ if (j > 0)
+ puts("\", \"");
+ puts(data);
+ j += strlen(data) + 1;
+ data += strlen(data) + 1;
+ }
+ puts("\"");
+ return;
+ }
+
+ switch (len) {
+ case 1: /* byte */
+ printf("<%02x>", (*(u8 *) data) & 0xff);
+ break;
+ case 2: /* half-word */
+ printf("<%04x>", be16_to_cpu(*(u16 *) data) & 0xffff);
+ break;
+ case 4: /* word */
+ printf("<%08x>", be32_to_cpu(*(u32 *) data) & 0xffffffffU);
+ break;
+ case 8: /* double-word */
+#if __WORDSIZE == 64
+ printf("<%016llx>", be64_to_cpu(*(uint64_t *) data));
+#else
+ printf("<%08x ", be32_to_cpu(*(u32 *) data) & 0xffffffffU);
+ data += 4;
+ printf("%08x>", be32_to_cpu(*(u32 *) data) & 0xffffffffU);
+#endif
+ break;
+ default: /* anything else... hexdump */
+ printf("[");
+ for (j = 0, s = data; j < len; j++)
+ printf("%02x%s", s[j], j < len - 1 ? " " : "");
+ printf("]");
+
+ break;
+ }
+}
+
+/********************************************************************/
+
+static int fdt_chosen(void *fdt, ulong initrd_start, ulong initrd_end)
+{
+ bd_t *bd = gd->bd;
+ int nodeoffset;
+ int err;
+ u32 tmp; /* used to set 32 bit integer properties */
+ char *str; /* used to set string properties */
+ ulong clock;
+
+ if (initrd_start && initrd_end) {
+ err = fdt_add_reservemap_entry(fdt,
+ initrd_start, initrd_end - initrd_start + 1);
+ if (err < 0) {
+ printf("libfdt: %s\n", fdt_strerror(err));
+ return err;
+ }
+ }
+
+ /*
+ * See if we already have a "chosen" node, create it if not.
+ */
+ nodeoffset = fdt_path_offset (fdt, "/chosen");
+ if (nodeoffset < 0) {
+ /*
+ * Create a new node "/chosen" (offset 0 is root level)
+ */
+ nodeoffset = fdt_add_subnode(fdt, 0, "chosen");
+ if (nodeoffset < 0) {
+ printf("libfdt: %s\n", fdt_strerror(nodeoffset));
+ return nodeoffset;
+ }
+ }
+
+ str = getenv("bootargs");
+ if (str != NULL) {
+ err = fdt_setprop(fdt, nodeoffset, "bootargs", str, strlen(str)+1);
+ if (err < 0)
+ printf("libfdt: %s\n", fdt_strerror(err));
+ }
+ if (initrd_start && initrd_end) {
+ tmp = __cpu_to_be32(initrd_start);
+ err = fdt_setprop(fdt, nodeoffset, "linux,initrd-start", &tmp, sizeof(tmp));
+ if (err < 0)
+ printf("libfdt: %s\n", fdt_strerror(err));
+ tmp = __cpu_to_be32(initrd_end);
+ err = fdt_setprop(fdt, nodeoffset, "linux,initrd-end", &tmp, sizeof(tmp));
+ if (err < 0)
+ printf("libfdt: %s\n", fdt_strerror(err));
+ }
+#ifdef OF_STDOUT_PATH
+ err = fdt_setprop(fdt, nodeoffset, "linux,stdout-path", OF_STDOUT_PATH, strlen(OF_STDOUT_PATH)+1);
+ if (err < 0)
+ printf("libfdt: %s\n", fdt_strerror(err));
+#endif
+
+ nodeoffset = fdt_path_offset (fdt, "/cpus");
+ if (nodeoffset >= 0) {
+ clock = cpu_to_be32(bd->bi_intfreq);
+ err = fdt_setprop(fdt, nodeoffset, "clock-frequency", &clock, 4);
+ if (err < 0)
+ printf("libfdt: %s\n", fdt_strerror(err));
+ }
+#ifdef OF_TBCLK
+ nodeoffset = fdt_path_offset (fdt, "/cpus/" OF_CPU "/timebase-frequency");
+ if (nodeoffset >= 0) {
+ clock = cpu_to_be32(OF_TBCLK);
+ err = fdt_setprop(fdt, nodeoffset, "clock-frequency", &clock, 4);
+ if (err < 0)
+ printf("libfdt: %s\n", fdt_strerror(err));
+ }
+#endif
+}
+
+/********************************************************************/
+
+#ifdef CONFIG_OF_HAS_BD_T
+
+/* Function that returns a character from the environment */
+extern uchar(*env_get_char) (int);
+
+#define BDM(x) { .name = #x, .offset = offsetof(bd_t, bi_ ##x ) }
+
+static const struct {
+ const char *name;
+ int offset;
+} bd_map[] = {
+ BDM(memstart),
+ BDM(memsize),
+ BDM(flashstart),
+ BDM(flashsize),
+ BDM(flashoffset),
+ BDM(sramstart),
+ BDM(sramsize),
+#if defined(CONFIG_5xx) || defined(CONFIG_8xx) || defined(CONFIG_8260) \
+ || defined(CONFIG_E500)
+ BDM(immr_base),
+#endif
+#if defined(CONFIG_MPC5xxx)
+ BDM(mbar_base),
+#endif
+#if defined(CONFIG_MPC83XX)
+ BDM(immrbar),
+#endif
+#if defined(CONFIG_MPC8220)
+ BDM(mbar_base),
+ BDM(inpfreq),
+ BDM(pcifreq),
+ BDM(pevfreq),
+ BDM(flbfreq),
+ BDM(vcofreq),
+#endif
+ BDM(bootflags),
+ BDM(ip_addr),
+ BDM(intfreq),
+ BDM(busfreq),
+#ifdef CONFIG_CPM2
+ BDM(cpmfreq),
+ BDM(brgfreq),
+ BDM(sccfreq),
+ BDM(vco),
+#endif
+#if defined(CONFIG_MPC5xxx)
+ BDM(ipbfreq),
+ BDM(pcifreq),
+#endif
+ BDM(baudrate),
+};
+
+static int fdt_env(void *fdt)
+{
+ int nodeoffset;
+ int err;
+ int k, nxt;
+ int i;
+ static char tmpenv[256];
+
+ /*
+ * See if we already have a "u-boot-env" node, delete it if so.
+ * Then create a new empty node.
+ */
+ nodeoffset = fdt_path_offset (fdt, "/u-boot-env");
+ if (nodeoffset >= 0) {
+ err = fdt_del_node(fdt, nodeoffset);
+ if (err < 0) {
+ printf("libfdt: %s\n", fdt_strerror(err));
+ return err;
+ }
+ }
+ /*
+ * Create a new node "/u-boot-env" (offset 0 is root level)
+ */
+ nodeoffset = fdt_add_subnode(fdt, 0, "u-boot-env");
+ if (nodeoffset < 0) {
+ printf("libfdt: %s\n", fdt_strerror(nodeoffset));
+ return nodeoffset;
+ }
+
+ for (i = 0; env_get_char(i) != '\0'; i = nxt + 1) {
+ char *s, *lval, *rval;
+
+ /*
+ * Find the end of the name=definition
+ */
+ for (nxt = i; env_get_char(nxt) != '\0'; ++nxt)
+ ;
+ s = tmpenv;
+ for (k = i; k < nxt && s < &tmpenv[sizeof(tmpenv) - 1]; ++k)
+ *s++ = env_get_char(k);
+ *s++ = '\0';
+ lval = tmpenv;
+ /*
+ * Find the first '=': it separates the name from the value
+ */
+ s = strchr(tmpenv, '=');
+ if (s != NULL) {
+ *s++ = '\0';
+ rval = s;
+ } else
+ continue;
+ err = fdt_setprop(fdt, nodeoffset, lval, rval, strlen(rval)+1);
+ if (err < 0) {
+ printf("\"%s\" - libfdt: %s\n", lval, fdt_strerror(err));
+ return err;
+ }
+ }
+ return 0;
+}
+#endif /* CONFIG_OF_HAS_UBOOT_ENV */
+
+/********************************************************************/
+
+#ifdef CONFIG_OF_HAS_BD_T
+static int fdt_bd_t(void *fdt)
+{
+ bd_t *bd = gd->bd;
+ int nodeoffset;
+ int err;
+ u32 tmp; /* used to set 32 bit integer properties */
+ int i;
+
+ /*
+ * See if we already have a "bd_t" node, delete it if so.
+ * Then create a new empty node.
+ */
+ nodeoffset = fdt_path_offset (fdt, "/bd_t");
+ if (nodeoffset >= 0) {
+ err = fdt_del_node(fdt, nodeoffset);
+ if (err < 0) {
+ printf("libfdt: %s\n", fdt_strerror(err));
+ return err;
+ }
+ }
+ /*
+ * Create a new node "/bd_t" (offset 0 is root level)
+ */
+ nodeoffset = fdt_add_subnode(fdt, 0, "bd_t");
+ if (nodeoffset < 0) {
+ printf("libfdt: %s\n", fdt_strerror(nodeoffset));
+ return nodeoffset;
+ }
+ /*
+ * Use the string/pointer structure to create the entries...
+ */
+ for (i = 0; i < sizeof(bd_map)/sizeof(bd_map[0]); i++) {
+ tmp = cpu_to_be32(getenv("bootargs"));
+ err = fdt_setprop(fdt, nodeoffset, bd_map[i].name, &tmp, sizeof(tmp));
+ if (err < 0)
+ printf("libfdt: %s\n", fdt_strerror(err));
+ }
+ /*
+ * Add a couple of oddball entries...
+ */
+ err = fdt_setprop(fdt, nodeoffset, "enetaddr", &bd->bi_enetaddr, 6);
+ if (err < 0)
+ printf("libfdt: %s\n", fdt_strerror(err));
+ err = fdt_setprop(fdt, nodeoffset, "ethspeed", &bd->bi_ethspeed, 4);
+ if (err < 0)
+ printf("libfdt: %s\n", fdt_strerror(err));
+
+#ifdef CONFIG_OF_BOARD_SETUP
+ ft_board_setup(fdt, bd);
+#endif
+
+ return 0;
+}
+#endif /* CONFIG_OF_HAS_BD_T */
+
+/********************************************************************/
+
+U_BOOT_CMD(
+ fdt, 5, 0, do_fdt,
+ "fdt - flattened device tree utility commands\n",
+ "addr <addr> [<length>] - Set the fdt location to <addr>\n"
+ "fdt move <fdt> <newaddr> <length> - Copy the fdt to <addr>\n"
+ "fdt print <path> [<prop>] - Recursive print starting at <path>\n"
+ "fdt list <path> [<prop>] - Print one level starting at <path>\n"
+ "fdt set <path> <prop> [<val>] - Set <property> [to <val>]\n"
+ "fdt mknode <path> <node> - Create a new node after <path>\n"
+ "fdt rm <path> [<prop>] - Delete the node or <property>\n"
+ "fdt chosen - Add/update the \"/chosen\" branch in the tree\n"
+#ifdef CONFIG_OF_HAS_UBOOT_ENV
+ "fdt env - Add/replace the \"/u-boot-env\" branch in the tree\n"
+#endif
+#ifdef CONFIG_OF_HAS_BD_T
+ "fdt bd_t - Add/replace the \"/bd_t\" branch in the tree\n"
+#endif
+ "Hints:\n"
+ " * Set a larger length with the fdt addr command to add to the blob.\n"
+ " * If the property you are setting/printing has a '#' character,\n"
+ " you MUST escape it with a \\ character or quote it with \" or\n"
+ " it will be ignored as a comment.\n"
+ " * If the value has spaces in it, you MUST escape the spaces with\n"
+ " \\ characters or quote it with \"\"\n"
+ "Examples: fdt print / # print the whole tree\n"
+ " fdt print /cpus \"#address-cells\"\n"
+ " fdt set /cpus \"#address-cells\" \"[00 00 00 01]\"\n"
+);
+
+#endif /* CONFIG_OF_FLAT_TREE */
diff --git a/common/cmd_i2c.c b/common/cmd_i2c.c
index 34571ee..755810d 100644
--- a/common/cmd_i2c.c
+++ b/common/cmd_i2c.c
@@ -969,7 +969,7 @@
"i2c sdram chip - print SDRAM configuration information\n"
#endif /* CFG_CMD_SDRAM */
);
-#else /* CONFIG_I2C_CMD_TREE */
+#endif /* CONFIG_I2C_CMD_TREE */
U_BOOT_CMD(
imd, 4, 1, do_i2c_md, \
"imd - i2c memory display\n", \
@@ -1024,6 +1024,5 @@
" (valid chip values 50..57)\n"
);
#endif
-#endif /* CONFIG_I2C_CMD_TREE */
#endif /* CFG_CMD_I2C */
diff --git a/common/cmd_ide.c b/common/cmd_ide.c
index 2e185cc..ce99a41 100644
--- a/common/cmd_ide.c
+++ b/common/cmd_ide.c
@@ -423,7 +423,7 @@
}
part = simple_strtoul(++ep, NULL, 16);
}
- if (get_partition_info (ide_dev_desc, part, &info)) {
+ if (get_partition_info (&ide_dev_desc[dev], part, &info)) {
SHOW_BOOT_PROGRESS (-1);
return 1;
}
@@ -513,9 +513,11 @@
#endif
unsigned char c;
int i, bus;
+#if defined(CONFIG_AMIGAONEG3SE) || defined(CONFIG_SC3)
+ unsigned int ata_reset_time;
+#endif
#ifdef CONFIG_AMIGAONEG3SE
unsigned int max_bus_scan;
- unsigned int ata_reset_time;
char *s;
#endif
#ifdef CONFIG_IDE_8xx_PCCARD
@@ -617,10 +619,9 @@
udelay (100000); /* 100 ms */
ide_outb (dev, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(dev));
udelay (100000); /* 100 ms */
-#ifdef CONFIG_AMIGAONEG3SE
- ata_reset_time = ATA_RESET_TIME;
- s = getenv("ide_reset_timeout");
- if (s) ata_reset_time = 2*simple_strtol(s, NULL, 10);
+#if defined(CONFIG_AMIGAONEG3SE) || defined(CONFIG_SC3)
+ if ((s = getenv("ide_reset_timeout")) != NULL)
+ ata_reset_time = simple_strtol(s, NULL, 10);
#endif
i = 0;
do {
@@ -628,7 +629,7 @@
c = ide_inb (dev, ATA_STATUS);
i++;
-#ifdef CONFIG_AMIGAONEG3SE
+#if defined(CONFIG_AMIGAONEG3SE) || defined(CONFIG_SC3)
if (i > (ata_reset_time * 100)) {
#else
if (i > (ATA_RESET_TIME * 100)) {
@@ -1343,7 +1344,7 @@
++n;
++blknr;
- buffer += ATA_SECTORWORDS;
+ buffer += ATA_BLOCKSIZE;
}
IDE_READ_E:
ide_led (DEVICE_LED(device), 0); /* LED off */
@@ -1427,7 +1428,7 @@
c = ide_inb (device, ATA_STATUS); /* clear IRQ */
++n;
++blknr;
- buffer += ATA_SECTORWORDS;
+ buffer += ATA_BLOCKSIZE;
}
WR_OUT:
ide_led (DEVICE_LED(device), 0); /* LED off */
@@ -2051,7 +2052,7 @@
n+=cnt;
blkcnt-=cnt;
blknr+=cnt;
- buffer+=cnt*(ATAPI_READ_BLOCK_SIZE/4); /* ulong blocksize in ulong */
+ buffer+=(cnt*ATAPI_READ_BLOCK_SIZE);
} while (blkcnt > 0);
return (n);
}
diff --git a/common/cmd_scsi.c b/common/cmd_scsi.c
index da36ed9..00b84fa 100644
--- a/common/cmd_scsi.c
+++ b/common/cmd_scsi.c
@@ -248,7 +248,7 @@
}
part = simple_strtoul(++ep, NULL, 16);
}
- if (get_partition_info (scsi_dev_desc, part, &info)) {
+ if (get_partition_info (&scsi_dev_desc[dev], part, &info)) {
printf("error reading partinfo\n");
return 1;
}
diff --git a/common/serial.c b/common/serial.c
index 605d4e3..13e9f30 100644
--- a/common/serial.c
+++ b/common/serial.c
@@ -41,7 +41,7 @@
|| defined(CONFIG_8xx_CONS_SCC3) || defined(CONFIG_8xx_CONS_SCC4)
return &serial_scc_device;
#elif defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_440) \
- || defined(CONFIG_405EP) || defined(CONFIG_MPC5xxx)
+ || defined(CONFIG_405EP) || defined(CONFIG_405EZ) || defined(CONFIG_MPC5xxx)
#if defined(CONFIG_CONS_INDEX) && defined(CFG_NS16550_SERIAL)
#if (CONFIG_CONS_INDEX==1)
return &eserial1_device;
@@ -91,7 +91,7 @@
#endif
#if defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_440) \
- || defined(CONFIG_405EP) || defined(CONFIG_MPC5xxx)
+ || defined(CONFIG_405EP) || defined(CONFIG_405EZ) || defined(CONFIG_MPC5xxx)
serial_register(&serial0_device);
serial_register(&serial1_device);
#endif
diff --git a/cpu/74xx_7xx/cpu.c b/cpu/74xx_7xx/cpu.c
index f4e5fc5..9c8998b 100644
--- a/cpu/74xx_7xx/cpu.c
+++ b/cpu/74xx_7xx/cpu.c
@@ -44,6 +44,10 @@
#include <74xx_7xx.h>
#include <asm/cache.h>
+#if defined(CONFIG_OF_FLAT_TREE)
+#include <ft_build.h>
+#endif
+
#ifdef CONFIG_AMIGAONEG3SE
#include "../board/MAI/AmigaOneG3SE/via686.h"
#include "../board/MAI/AmigaOneG3SE/memio.h"
@@ -101,6 +105,10 @@
type = CPU_7457;
break;
+ case 0x8003:
+ type = CPU_7447A;
+ break;
+
case 0x8004:
type = CPU_7448;
break;
@@ -156,6 +164,10 @@
str = "MPC7410";
break;
+ case CPU_7447A:
+ str = "MPC7447A";
+ break;
+
case CPU_7448:
str = "MPC7448";
break;
@@ -264,20 +276,19 @@
/*
* For the 7400 the TB clock runs at 1/4 the cpu bus speed.
*/
-#ifdef CONFIG_AMIGAONEG3SE
+#if defined(CONFIG_AMIGAONEG3SE) || defined(CFG_CONFIG_BUS_CLK)
unsigned long get_tbclk(void)
{
return (gd->bus_clk / 4);
}
-#else /* ! CONFIG_AMIGAONEG3SE */
+#else /* ! CONFIG_AMIGAONEG3SE and !CFG_CONFIG_BUS_CLK*/
unsigned long get_tbclk (void)
{
return CFG_BUS_HZ / 4;
}
-#endif /* CONFIG_AMIGAONEG3SE */
+#endif /* CONFIG_AMIGAONEG3SE or CFG_CONFIG_BUS_CLK*/
/* ------------------------------------------------------------------------- */
-
#if defined(CONFIG_WATCHDOG)
#if !defined(CONFIG_PCIPPC2) && !defined(CONFIG_BAB7xx)
void
@@ -288,4 +299,31 @@
#endif /* !CONFIG_PCIPPC2 && !CONFIG_BAB7xx */
#endif /* CONFIG_WATCHDOG */
+/* ------------------------------------------------------------------------- */
+
+#ifdef CONFIG_OF_FLAT_TREE
+void
+ft_cpu_setup (void *blob, bd_t *bd)
+{
+ u32 *p;
+ ulong clock;
+ int len;
+
+ clock = bd->bi_busfreq;
+
+ p = ft_get_prop (blob, "/cpus/" OF_CPU "/bus-frequency", &len);
+ if (p != NULL)
+ *p = cpu_to_be32 (clock);
+
+#if defined(CONFIG_TSI108_ETH)
+ p = ft_get_prop (blob, "/" OF_TSI "/ethernet@6200/address", &len);
+ memcpy (p, bd->bi_enetaddr, 6);
+#endif
+
+#if defined(CONFIG_HAS_ETH1)
+ p = ft_get_prop (blob, "/" OF_TSI "/ethernet@6600/address", &len);
+ memcpy (p, bd->bi_enet1addr, 6);
+#endif
+}
+#endif
/* ------------------------------------------------------------------------- */
diff --git a/cpu/74xx_7xx/cpu_init.c b/cpu/74xx_7xx/cpu_init.c
index e02a4cc..1dd1b2c 100644
--- a/cpu/74xx_7xx/cpu_init.c
+++ b/cpu/74xx_7xx/cpu_init.c
@@ -43,6 +43,7 @@
case CPU_7450:
case CPU_7455:
case CPU_7457:
+ case CPU_7447A:
case CPU_7448:
/* enable the timebase bit in HID0 */
set_hid0(get_hid0() | 0x4000000);
diff --git a/cpu/74xx_7xx/speed.c b/cpu/74xx_7xx/speed.c
index d1800ed..d8c40ce 100644
--- a/cpu/74xx_7xx/speed.c
+++ b/cpu/74xx_7xx/speed.c
@@ -31,6 +31,8 @@
DECLARE_GLOBAL_DATA_PTR;
+extern unsigned long get_board_bus_clk (void);
+
static const int hid1_multipliers_x_10[] = {
25, /* 0000 - 2.5x */
75, /* 0001 - 7.5x */
@@ -50,6 +52,42 @@
0 /* 1111 - off */
};
+/* PLL_CFG[0:4] table for cpu 7448/7447A/7455/7457 */
+static const int hid1_74xx_multipliers_x_10[] = {
+ 115, /* 00000 - 11.5x */
+ 170, /* 00001 - 17x */
+ 75, /* 00010 - 7.5x */
+ 150, /* 00011 - 15x */
+ 70, /* 00100 - 7x */
+ 180, /* 00101 - 18x */
+ 10, /* 00110 - bypass */
+ 200, /* 00111 - 20x */
+ 20, /* 01000 - 2x */
+ 210, /* 01001 - 21x */
+ 65, /* 01010 - 6.5x */
+ 130, /* 01011 - 13x */
+ 85, /* 01100 - 8.5x */
+ 240, /* 01101 - 24x */
+ 95, /* 01110 - 9.5x */
+ 90, /* 01111 - 9x */
+ 30, /* 10000 - 3x */
+ 105, /* 10001 - 10.5x */
+ 55, /* 10010 - 5.5x */
+ 110, /* 10011 - 11x */
+ 40, /* 10100 - 4x */
+ 100, /* 10101 - 10x */
+ 50, /* 10110 - 5x */
+ 120, /* 10111 - 12x */
+ 80, /* 11000 - 8x */
+ 140, /* 11001 - 14x */
+ 60, /* 11010 - 6x */
+ 160, /* 11011 - 16x */
+ 135, /* 11100 - 13.5x */
+ 280, /* 11101 - 28x */
+ 0, /* 11110 - off */
+ 125 /* 11111 - 12.5x */
+};
+
static const int hid1_fx_multipliers_x_10[] = {
00, /* 0000 - off */
00, /* 0001 - off */
@@ -89,22 +127,30 @@
{
ulong clock = 0;
+#ifdef CFG_BUS_CLK
+ gd->bus_clk = CFG_BUS_CLK; /* bus clock is a fixed frequency */
+#else
+ gd->bus_clk = get_board_bus_clk (); /* bus clock is configurable */
+#endif
+
/* calculate the clock frequency based upon the CPU type */
switch (get_cpu_type()) {
+ case CPU_7447A:
case CPU_7448:
case CPU_7455:
case CPU_7457:
/*
- * It is assumed that the PLL_EXT line is zero.
* Make sure division is done before multiplication to prevent 32-bit
* arithmetic overflows which will cause a negative number
*/
- clock = (CFG_BUS_CLK / 10) * hid1_multipliers_x_10[(get_hid1 () >> 13) & 0xF];
+ clock = (gd->bus_clk / 10) *
+ hid1_74xx_multipliers_x_10[(get_hid1 () >> 12) & 0x1F];
break;
case CPU_750GX:
case CPU_750FX:
- clock = CFG_BUS_CLK * hid1_fx_multipliers_x_10[get_hid1 () >> 27] / 10;
+ clock = gd->bus_clk *
+ hid1_fx_multipliers_x_10[get_hid1 () >> 27] / 10;
break;
case CPU_7450:
@@ -121,7 +167,8 @@
* Make sure division is done before multiplication to prevent 32-bit
* arithmetic overflows which will cause a negative number
*/
- clock = (CFG_BUS_CLK / 10) * hid1_multipliers_x_10[get_hid1 () >> 28];
+ clock = (gd->bus_clk / 10) *
+ hid1_multipliers_x_10[get_hid1 () >> 28];
break;
case CPU_UNKNOWN:
@@ -131,7 +178,6 @@
}
gd->cpu_clk = clock;
- gd->bus_clk = CFG_BUS_CLK;
return (0);
}
diff --git a/cpu/at32ap/Makefile b/cpu/at32ap/Makefile
index f62ec8b..f69b1f3 100644
--- a/cpu/at32ap/Makefile
+++ b/cpu/at32ap/Makefile
@@ -30,7 +30,7 @@
START := start.o
SOBJS := entry.o
COBJS := cpu.o hsdramc.o exception.o cache.o
-COBJS += interrupts.o device.o pm.o pio.o
+COBJS += interrupts.o pio.o atmel_mci.o
SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
START := $(addprefix $(obj),$(START))
diff --git a/cpu/at32ap/at32ap7000/Makefile b/cpu/at32ap/at32ap7000/Makefile
index 2ed74d2..d276712 100644
--- a/cpu/at32ap/at32ap7000/Makefile
+++ b/cpu/at32ap/at32ap7000/Makefile
@@ -24,7 +24,7 @@
LIB := $(obj)lib$(SOC).a
-COBJS := hebi.o devices.o
+COBJS := gpio.o
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
diff --git a/cpu/at32ap/at32ap7000/devices.c b/cpu/at32ap/at32ap7000/devices.c
deleted file mode 100644
index 8b216e9..0000000
--- a/cpu/at32ap/at32ap7000/devices.c
+++ /dev/null
@@ -1,448 +0,0 @@
-/*
- * Copyright (C) 2006 Atmel Corporation
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-#include <common.h>
-
-#include <asm/arch/memory-map.h>
-#include <asm/arch/platform.h>
-
-#include "../sm.h"
-
-#define ARRAY_SIZE(x) (sizeof(x) / sizeof((x)[0]))
-
-const struct clock_domain chip_clock[] = {
- [CLOCK_CPU] = {
- .reg = SM_PM_CPU_MASK,
- .id = CLOCK_CPU,
- .bridge = NO_DEVICE,
- },
- [CLOCK_HSB] = {
- .reg = SM_PM_HSB_MASK,
- .id = CLOCK_HSB,
- .bridge = NO_DEVICE,
- },
- [CLOCK_PBA] = {
- .reg = SM_PM_PBA_MASK,
- .id = CLOCK_PBA,
- .bridge = DEVICE_PBA_BRIDGE,
- },
- [CLOCK_PBB] = {
- .reg = SM_PM_PBB_MASK,
- .id = CLOCK_PBB,
- .bridge = DEVICE_PBB_BRIDGE,
- },
-};
-
-static const struct resource hebi_resource[] = {
- {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_HSB, 0 },
- },
- }, {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_PBB, 13 },
- },
- }, {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_PBB, 14 },
- },
- }, {
- .type = RESOURCE_GPIO,
- .u = {
- .gpio = { 27, DEVICE_PIOE, GPIO_FUNC_A, 0 },
- },
- },
-};
-static const struct resource pba_bridge_resource[] = {
- {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_HSB, 1 },
- }
- }, {
- .type = RESOURCE_CLOCK,
- .u = {
- /* HSB-HSB Bridge */
- .clock = { CLOCK_HSB, 4 },
- },
- },
-};
-static const struct resource pbb_bridge_resource[] = {
- {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_HSB, 2 },
- },
- },
-};
-static const struct resource hramc_resource[] = {
- {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_HSB, 3 },
- },
- },
-};
-static const struct resource pioa_resource[] = {
- {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_PBA, 10 },
- },
- },
-};
-static const struct resource piob_resource[] = {
- {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_PBA, 11 },
- },
- },
-};
-static const struct resource pioc_resource[] = {
- {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_PBA, 12 },
- },
- },
-};
-static const struct resource piod_resource[] = {
- {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_PBA, 13 },
- },
- },
-};
-static const struct resource pioe_resource[] = {
- {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_PBA, 14 },
- },
- },
-};
-static const struct resource sm_resource[] = {
- {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_PBB, 0 },
- },
- },
-};
-static const struct resource intc_resource[] = {
- {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_PBB, 1 },
- },
- },
-};
-static const struct resource hmatrix_resource[] = {
- {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_PBB, 2 },
- },
- },
-};
-#if defined(CFG_HPDC)
-static const struct resource hpdc_resource[] = {
- {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_PBA, 16 },
- },
- },
-};
-#endif
-#if defined(CFG_MACB0)
-static const struct resource macb0_resource[] = {
- {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_HSB, 8 },
- },
- }, {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_PBB, 6 },
- },
- }, {
- .type = RESOURCE_GPIO,
- .u = {
- .gpio = { 19, DEVICE_PIOC, GPIO_FUNC_A, 0 },
- },
- },
-};
-#endif
-#if defined(CFG_MACB1)
-static const struct resource macb1_resource[] = {
- {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_HSB, 9 },
- },
- }, {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_PBB, 7 },
- },
- }, {
- .type = RESOURCE_GPIO,
- .u = {
- .gpio = { 12, DEVICE_PIOC, GPIO_FUNC_B, 19 },
- },
- }, {
- .type = RESOURCE_GPIO,
- .u = {
- .gpio = { 14, DEVICE_PIOD, GPIO_FUNC_B, 2 },
- },
- },
-};
-#endif
-#if defined(CFG_LCDC)
-static const struct resource lcdc_resource[] = {
- {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_HSB, 7 },
- },
- },
-};
-#endif
-#if defined(CFG_USART0)
-static const struct resource usart0_resource[] = {
- {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_PBA, 3 },
- },
- }, {
- .type = RESOURCE_GPIO,
- .u = {
- .gpio = { 2, DEVICE_PIOA, GPIO_FUNC_B, 8 },
- },
- },
-};
-#endif
-#if defined(CFG_USART1)
-static const struct resource usart1_resource[] = {
- {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_PBA, 4 },
- },
- }, {
- .type = RESOURCE_GPIO,
- .u = {
- .gpio = { 2, DEVICE_PIOA, GPIO_FUNC_A, 17 },
- },
- },
-};
-#endif
-#if defined(CFG_USART2)
-static const struct resource usart2_resource[] = {
- {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_PBA, 5 },
- },
- }, {
- .type = RESOURCE_GPIO,
- .u = {
- .gpio = { 2, DEVICE_PIOB, GPIO_FUNC_B, 26 },
- },
- },
-};
-#endif
-#if defined(CFG_USART3)
-static const struct resource usart3_resource[] = {
- {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_PBA, 6 },
- },
- }, {
- .type = RESOURCE_GPIO,
- .u = {
- .gpio = { 2, DEVICE_PIOB, GPIO_FUNC_B, 17 },
- },
- },
-};
-#endif
-#if defined(CFG_MMCI)
-static const struct resource mmci_resource[] = {
- {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_PBB, 9 },
- },
- }, {
- .type = RESOURCE_GPIO,
- .u = {
- .gpio = { 6, DEVICE_PIOA, GPIO_FUNC_A, 10 },
- },
- },
-};
-#endif
-#if defined(CFG_DMAC)
-static const struct resource dmac_resource[] = {
- {
- .type = RESOURCE_CLOCK,
- .u = {
- .clock = { CLOCK_HSB, 10 },
- },
- },
-};
-#endif
-
-const struct device chip_device[] = {
- [DEVICE_HEBI] = {
- .regs = (void *)HSMC_BASE,
- .nr_resources = ARRAY_SIZE(hebi_resource),
- .resource = hebi_resource,
- },
- [DEVICE_PBA_BRIDGE] = {
- .nr_resources = ARRAY_SIZE(pba_bridge_resource),
- .resource = pba_bridge_resource,
- },
- [DEVICE_PBB_BRIDGE] = {
- .nr_resources = ARRAY_SIZE(pbb_bridge_resource),
- .resource = pbb_bridge_resource,
- },
- [DEVICE_HRAMC] = {
- .nr_resources = ARRAY_SIZE(hramc_resource),
- .resource = hramc_resource,
- },
- [DEVICE_PIOA] = {
- .regs = (void *)PIOA_BASE,
- .nr_resources = ARRAY_SIZE(pioa_resource),
- .resource = pioa_resource,
- },
- [DEVICE_PIOB] = {
- .regs = (void *)PIOB_BASE,
- .nr_resources = ARRAY_SIZE(piob_resource),
- .resource = piob_resource,
- },
- [DEVICE_PIOC] = {
- .regs = (void *)PIOC_BASE,
- .nr_resources = ARRAY_SIZE(pioc_resource),
- .resource = pioc_resource,
- },
- [DEVICE_PIOD] = {
- .regs = (void *)PIOD_BASE,
- .nr_resources = ARRAY_SIZE(piod_resource),
- .resource = piod_resource,
- },
- [DEVICE_PIOE] = {
- .regs = (void *)PIOE_BASE,
- .nr_resources = ARRAY_SIZE(pioe_resource),
- .resource = pioe_resource,
- },
- [DEVICE_SM] = {
- .regs = (void *)SM_BASE,
- .nr_resources = ARRAY_SIZE(sm_resource),
- .resource = sm_resource,
- },
- [DEVICE_INTC] = {
- .regs = (void *)INTC_BASE,
- .nr_resources = ARRAY_SIZE(intc_resource),
- .resource = intc_resource,
- },
- [DEVICE_HMATRIX] = {
- .regs = (void *)HMATRIX_BASE,
- .nr_resources = ARRAY_SIZE(hmatrix_resource),
- .resource = hmatrix_resource,
- },
-#if defined(CFG_HPDC)
- [DEVICE_HPDC] = {
- .nr_resources = ARRAY_SIZE(hpdc_resource),
- .resource = hpdc_resource,
- },
-#endif
-#if defined(CFG_MACB0)
- [DEVICE_MACB0] = {
- .regs = (void *)MACB0_BASE,
- .nr_resources = ARRAY_SIZE(macb0_resource),
- .resource = macb0_resource,
- },
-#endif
-#if defined(CFG_MACB1)
- [DEVICE_MACB1] = {
- .regs = (void *)MACB1_BASE,
- .nr_resources = ARRAY_SIZE(macb1_resource),
- .resource = macb1_resource,
- },
-#endif
-#if defined(CFG_LCDC)
- [DEVICE_LCDC] = {
- .nr_resources = ARRAY_SIZE(lcdc_resource),
- .resource = lcdc_resource,
- },
-#endif
-#if defined(CFG_USART0)
- [DEVICE_USART0] = {
- .regs = (void *)USART0_BASE,
- .nr_resources = ARRAY_SIZE(usart0_resource),
- .resource = usart0_resource,
- },
-#endif
-#if defined(CFG_USART1)
- [DEVICE_USART1] = {
- .regs = (void *)USART1_BASE,
- .nr_resources = ARRAY_SIZE(usart1_resource),
- .resource = usart1_resource,
- },
-#endif
-#if defined(CFG_USART2)
- [DEVICE_USART2] = {
- .regs = (void *)USART2_BASE,
- .nr_resources = ARRAY_SIZE(usart2_resource),
- .resource = usart2_resource,
- },
-#endif
-#if defined(CFG_USART3)
- [DEVICE_USART3] = {
- .regs = (void *)USART3_BASE,
- .nr_resources = ARRAY_SIZE(usart3_resource),
- .resource = usart3_resource,
- },
-#endif
-#if defined(CFG_MMCI)
- [DEVICE_MMCI] = {
- .regs = (void *)MMCI_BASE,
- .nr_resources = ARRAY_SIZE(mmci_resource),
- .resource = mmci_resource,
- },
-#endif
-#if defined(CFG_DMAC)
- [DEVICE_DMAC] = {
- .regs = (void *)DMAC_BASE,
- .nr_resources = ARRAY_SIZE(dmac_resource),
- .resource = dmac_resource,
- },
-#endif
-};
diff --git a/cpu/at32ap/at32ap7000/gpio.c b/cpu/at32ap/at32ap7000/gpio.c
new file mode 100644
index 0000000..52f5372
--- /dev/null
+++ b/cpu/at32ap/at32ap7000/gpio.c
@@ -0,0 +1,137 @@
+/*
+ * Copyright (C) 2006 Atmel Corporation
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+
+#include <asm/arch/gpio.h>
+
+/*
+ * Lots of small functions here. We depend on --gc-sections getting
+ * rid of the ones we don't need.
+ */
+void gpio_enable_ebi(void)
+{
+#ifdef CFG_HSDRAMC
+#ifndef CFG_SDRAM_16BIT
+ gpio_select_periph_A(GPIO_PIN_PE0, 0);
+ gpio_select_periph_A(GPIO_PIN_PE1, 0);
+ gpio_select_periph_A(GPIO_PIN_PE2, 0);
+ gpio_select_periph_A(GPIO_PIN_PE3, 0);
+ gpio_select_periph_A(GPIO_PIN_PE4, 0);
+ gpio_select_periph_A(GPIO_PIN_PE5, 0);
+ gpio_select_periph_A(GPIO_PIN_PE6, 0);
+ gpio_select_periph_A(GPIO_PIN_PE7, 0);
+ gpio_select_periph_A(GPIO_PIN_PE8, 0);
+ gpio_select_periph_A(GPIO_PIN_PE9, 0);
+ gpio_select_periph_A(GPIO_PIN_PE10, 0);
+ gpio_select_periph_A(GPIO_PIN_PE11, 0);
+ gpio_select_periph_A(GPIO_PIN_PE12, 0);
+ gpio_select_periph_A(GPIO_PIN_PE13, 0);
+ gpio_select_periph_A(GPIO_PIN_PE14, 0);
+ gpio_select_periph_A(GPIO_PIN_PE15, 0);
+#endif
+ gpio_select_periph_A(GPIO_PIN_PE26, 0);
+#endif
+}
+
+void gpio_enable_usart0(void)
+{
+ gpio_select_periph_B(GPIO_PIN_PA8, 0);
+ gpio_select_periph_B(GPIO_PIN_PA9, 0);
+}
+
+void gpio_enable_usart1(void)
+{
+ gpio_select_periph_A(GPIO_PIN_PA17, 0);
+ gpio_select_periph_A(GPIO_PIN_PA18, 0);
+}
+
+void gpio_enable_usart2(void)
+{
+ gpio_select_periph_B(GPIO_PIN_PB26, 0);
+ gpio_select_periph_B(GPIO_PIN_PB27, 0);
+}
+
+void gpio_enable_usart3(void)
+{
+ gpio_select_periph_B(GPIO_PIN_PB18, 0);
+ gpio_select_periph_B(GPIO_PIN_PB19, 0);
+}
+
+void gpio_enable_macb0(void)
+{
+ gpio_select_periph_A(GPIO_PIN_PC3, 0); /* TXD0 */
+ gpio_select_periph_A(GPIO_PIN_PC4, 0); /* TXD1 */
+ gpio_select_periph_A(GPIO_PIN_PC7, 0); /* TXEN */
+ gpio_select_periph_A(GPIO_PIN_PC8, 0); /* TXCK */
+ gpio_select_periph_A(GPIO_PIN_PC9, 0); /* RXD0 */
+ gpio_select_periph_A(GPIO_PIN_PC10, 0); /* RXD1 */
+ gpio_select_periph_A(GPIO_PIN_PC13, 0); /* RXER */
+ gpio_select_periph_A(GPIO_PIN_PC15, 0); /* RXDV */
+ gpio_select_periph_A(GPIO_PIN_PC16, 0); /* MDC */
+ gpio_select_periph_A(GPIO_PIN_PC17, 0); /* MDIO */
+#if !defined(CONFIG_RMII)
+ gpio_select_periph_A(GPIO_PIN_PC0, 0); /* COL */
+ gpio_select_periph_A(GPIO_PIN_PC1, 0); /* CRS */
+ gpio_select_periph_A(GPIO_PIN_PC2, 0); /* TXER */
+ gpio_select_periph_A(GPIO_PIN_PC5, 0); /* TXD2 */
+ gpio_select_periph_A(GPIO_PIN_PC6, 0); /* TXD3 */
+ gpio_select_periph_A(GPIO_PIN_PC11, 0); /* RXD2 */
+ gpio_select_periph_A(GPIO_PIN_PC12, 0); /* RXD3 */
+ gpio_select_periph_A(GPIO_PIN_PC14, 0); /* RXCK */
+ gpio_select_periph_A(GPIO_PIN_PC18, 0); /* SPD */
+#endif
+}
+
+void gpio_enable_macb1(void)
+{
+ gpio_select_periph_B(GPIO_PIN_PD13, 0); /* TXD0 */
+ gpio_select_periph_B(GPIO_PIN_PD14, 0); /* TXD1 */
+ gpio_select_periph_B(GPIO_PIN_PD11, 0); /* TXEN */
+ gpio_select_periph_B(GPIO_PIN_PD12, 0); /* TXCK */
+ gpio_select_periph_B(GPIO_PIN_PD10, 0); /* RXD0 */
+ gpio_select_periph_B(GPIO_PIN_PD6, 0); /* RXD1 */
+ gpio_select_periph_B(GPIO_PIN_PD5, 0); /* RXER */
+ gpio_select_periph_B(GPIO_PIN_PD4, 0); /* RXDV */
+ gpio_select_periph_B(GPIO_PIN_PD3, 0); /* MDC */
+ gpio_select_periph_B(GPIO_PIN_PD2, 0); /* MDIO */
+#if !defined(CONFIG_RMII)
+ gpio_select_periph_B(GPIO_PIN_PC19, 0); /* COL */
+ gpio_select_periph_B(GPIO_PIN_PC23, 0); /* CRS */
+ gpio_select_periph_B(GPIO_PIN_PC26, 0); /* TXER */
+ gpio_select_periph_B(GPIO_PIN_PC27, 0); /* TXD2 */
+ gpio_select_periph_B(GPIO_PIN_PC28, 0); /* TXD3 */
+ gpio_select_periph_B(GPIO_PIN_PC29, 0); /* RXD2 */
+ gpio_select_periph_B(GPIO_PIN_PC30, 0); /* RXD3 */
+ gpio_select_periph_B(GPIO_PIN_PC24, 0); /* RXCK */
+ gpio_select_periph_B(GPIO_PIN_PD15, 0); /* SPD */
+#endif
+}
+
+void gpio_enable_mmci(void)
+{
+ gpio_select_periph_A(GPIO_PIN_PA10, 0); /* CLK */
+ gpio_select_periph_A(GPIO_PIN_PA11, 0); /* CMD */
+ gpio_select_periph_A(GPIO_PIN_PA12, 0); /* DATA0 */
+ gpio_select_periph_A(GPIO_PIN_PA13, 0); /* DATA1 */
+ gpio_select_periph_A(GPIO_PIN_PA14, 0); /* DATA2 */
+ gpio_select_periph_A(GPIO_PIN_PA15, 0); /* DATA3 */
+}
diff --git a/cpu/at32ap/atmel_mci.c b/cpu/at32ap/atmel_mci.c
new file mode 100644
index 0000000..9f62c0f
--- /dev/null
+++ b/cpu/at32ap/atmel_mci.c
@@ -0,0 +1,477 @@
+/*
+ * Copyright (C) 2004-2006 Atmel Corporation
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+
+#ifdef CONFIG_MMC
+
+#include <part.h>
+#include <mmc.h>
+
+#include <asm/io.h>
+#include <asm/errno.h>
+#include <asm/byteorder.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/memory-map.h>
+
+#include "atmel_mci.h"
+
+#ifdef DEBUG
+#define pr_debug(fmt, args...) printf(fmt, ##args)
+#else
+#define pr_debug(...) do { } while(0)
+#endif
+
+#ifndef CFG_MMC_CLK_OD
+#define CFG_MMC_CLK_OD 150000
+#endif
+
+#ifndef CFG_MMC_CLK_PP
+#define CFG_MMC_CLK_PP 5000000
+#endif
+
+#ifndef CFG_MMC_OP_COND
+#define CFG_MMC_OP_COND 0x00100000
+#endif
+
+#define MMC_DEFAULT_BLKLEN 512
+#define MMC_DEFAULT_RCA 1
+
+static unsigned int mmc_rca;
+static block_dev_desc_t mmc_blkdev;
+
+block_dev_desc_t *mmc_get_dev(int dev)
+{
+ return &mmc_blkdev;
+}
+
+static void mci_set_mode(unsigned long hz, unsigned long blklen)
+{
+ unsigned long bus_hz;
+ unsigned long clkdiv;
+
+ bus_hz = get_mci_clk_rate();
+ clkdiv = (bus_hz / hz) / 2 - 1;
+
+ pr_debug("mmc: setting clock %lu Hz, block size %lu\n",
+ hz, blklen);
+
+ if (clkdiv & ~255UL) {
+ clkdiv = 255;
+ printf("mmc: clock %lu too low; setting CLKDIV to 255\n",
+ hz);
+ }
+
+ blklen &= 0xfffc;
+ mmci_writel(MR, (MMCI_BF(CLKDIV, clkdiv)
+ | MMCI_BF(BLKLEN, blklen)));
+}
+
+#define RESP_NO_CRC 1
+#define R1 MMCI_BF(RSPTYP, 1)
+#define R2 MMCI_BF(RSPTYP, 2)
+#define R3 (R1 | RESP_NO_CRC)
+#define R6 R1
+#define NID MMCI_BF(MAXLAT, 0)
+#define NCR MMCI_BF(MAXLAT, 1)
+#define TRCMD_START MMCI_BF(TRCMD, 1)
+#define TRDIR_READ MMCI_BF(TRDIR, 1)
+#define TRTYP_BLOCK MMCI_BF(TRTYP, 0)
+#define INIT_CMD MMCI_BF(SPCMD, 1)
+#define OPEN_DRAIN MMCI_BF(OPDCMD, 1)
+
+#define ERROR_FLAGS (MMCI_BIT(DTOE) \
+ | MMCI_BIT(RDIRE) \
+ | MMCI_BIT(RENDE) \
+ | MMCI_BIT(RINDE) \
+ | MMCI_BIT(RTOE))
+
+static int
+mmc_cmd(unsigned long cmd, unsigned long arg,
+ void *resp, unsigned long flags)
+{
+ unsigned long *response = resp;
+ int i, response_words = 0;
+ unsigned long error_flags;
+ u32 status;
+
+ pr_debug("mmc: CMD%lu 0x%lx (flags 0x%lx)\n",
+ cmd, arg, flags);
+
+ error_flags = ERROR_FLAGS;
+ if (!(flags & RESP_NO_CRC))
+ error_flags |= MMCI_BIT(RCRCE);
+
+ flags &= ~MMCI_BF(CMDNB, ~0UL);
+
+ if (MMCI_BFEXT(RSPTYP, flags) == MMCI_RSPTYP_48_BIT_RESP)
+ response_words = 1;
+ else if (MMCI_BFEXT(RSPTYP, flags) == MMCI_RSPTYP_136_BIT_RESP)
+ response_words = 4;
+
+ mmci_writel(ARGR, arg);
+ mmci_writel(CMDR, cmd | flags);
+ do {
+ udelay(40);
+ status = mmci_readl(SR);
+ } while (!(status & MMCI_BIT(CMDRDY)));
+
+ pr_debug("mmc: status 0x%08lx\n", status);
+
+ if (status & ERROR_FLAGS) {
+ printf("mmc: command %lu failed (status: 0x%08lx)\n",
+ cmd, status);
+ return -EIO;
+ }
+
+ if (response_words)
+ pr_debug("mmc: response:");
+
+ for (i = 0; i < response_words; i++) {
+ response[i] = mmci_readl(RSPR);
+ pr_debug(" %08lx", response[i]);
+ }
+ pr_debug("\n");
+
+ return 0;
+}
+
+static int mmc_acmd(unsigned long cmd, unsigned long arg,
+ void *resp, unsigned long flags)
+{
+ unsigned long aresp[4];
+ int ret;
+
+ /*
+ * Seems like the APP_CMD part of an ACMD has 64 cycles max
+ * latency even though the ACMD part doesn't. This isn't
+ * entirely clear in the SD Card spec, but some cards refuse
+ * to work if we attempt to use 5 cycles max latency here...
+ */
+ ret = mmc_cmd(MMC_CMD_APP_CMD, 0, aresp,
+ R1 | NCR | (flags & OPEN_DRAIN));
+ if (ret)
+ return ret;
+ if ((aresp[0] & (R1_ILLEGAL_COMMAND | R1_APP_CMD)) != R1_APP_CMD)
+ return -ENODEV;
+
+ ret = mmc_cmd(cmd, arg, resp, flags);
+ return ret;
+}
+
+static unsigned long
+mmc_bread(int dev, unsigned long start, lbaint_t blkcnt,
+ unsigned long *buffer)
+{
+ int ret, i = 0;
+ unsigned long resp[4];
+ unsigned long card_status, data;
+ unsigned long wordcount;
+ u32 status;
+
+ if (blkcnt == 0)
+ return 0;
+
+ pr_debug("mmc_bread: dev %d, start %lx, blkcnt %lx\n",
+ dev, start, blkcnt);
+
+ /* Put the device into Transfer state */
+ ret = mmc_cmd(MMC_CMD_SELECT_CARD, mmc_rca << 16, resp, R1 | NCR);
+ if (ret) goto fail;
+
+ /* Set block length */
+ ret = mmc_cmd(MMC_CMD_SET_BLOCKLEN, mmc_blkdev.blksz, resp, R1 | NCR);
+ if (ret) goto fail;
+
+ pr_debug("MCI_DTOR = %08lx\n", mmci_readl(DTOR));
+
+ for (i = 0; i < blkcnt; i++, start++) {
+ ret = mmc_cmd(MMC_CMD_READ_SINGLE_BLOCK,
+ start * mmc_blkdev.blksz, resp,
+ (R1 | NCR | TRCMD_START | TRDIR_READ
+ | TRTYP_BLOCK));
+ if (ret) goto fail;
+
+ ret = -EIO;
+ wordcount = 0;
+ do {
+ do {
+ status = mmci_readl(SR);
+ if (status & (ERROR_FLAGS | MMCI_BIT(OVRE)))
+ goto fail;
+ } while (!(status & MMCI_BIT(RXRDY)));
+
+ if (status & MMCI_BIT(RXRDY)) {
+ data = mmci_readl(RDR);
+ /* pr_debug("%x\n", data); */
+ *buffer++ = data;
+ wordcount++;
+ }
+ } while(wordcount < (512 / 4));
+
+ pr_debug("mmc: read %u words, waiting for BLKE\n", wordcount);
+
+ do {
+ status = mmci_readl(SR);
+ } while (!(status & MMCI_BIT(BLKE)));
+
+ putc('.');
+ }
+
+out:
+ /* Put the device back into Standby state */
+ mmc_cmd(MMC_CMD_SELECT_CARD, 0, resp, NCR);
+ return i;
+
+fail:
+ mmc_cmd(MMC_CMD_SEND_STATUS, mmc_rca << 16, &card_status, R1 | NCR);
+ printf("mmc: bread failed, card status = ", card_status);
+ goto out;
+}
+
+static void mmc_parse_cid(struct mmc_cid *cid, unsigned long *resp)
+{
+ cid->mid = resp[0] >> 24;
+ cid->oid = (resp[0] >> 8) & 0xffff;
+ cid->pnm[0] = resp[0];
+ cid->pnm[1] = resp[1] >> 24;
+ cid->pnm[2] = resp[1] >> 16;
+ cid->pnm[3] = resp[1] >> 8;
+ cid->pnm[4] = resp[1];
+ cid->pnm[5] = resp[2] >> 24;
+ cid->pnm[6] = 0;
+ cid->prv = resp[2] >> 16;
+ cid->psn = (resp[2] << 16) | (resp[3] >> 16);
+ cid->mdt = resp[3] >> 8;
+}
+
+static void sd_parse_cid(struct mmc_cid *cid, unsigned long *resp)
+{
+ cid->mid = resp[0] >> 24;
+ cid->oid = (resp[0] >> 8) & 0xffff;
+ cid->pnm[0] = resp[0];
+ cid->pnm[1] = resp[1] >> 24;
+ cid->pnm[2] = resp[1] >> 16;
+ cid->pnm[3] = resp[1] >> 8;
+ cid->pnm[4] = resp[1];
+ cid->pnm[5] = 0;
+ cid->pnm[6] = 0;
+ cid->prv = resp[2] >> 24;
+ cid->psn = (resp[2] << 8) | (resp[3] >> 24);
+ cid->mdt = (resp[3] >> 8) & 0x0fff;
+}
+
+static void mmc_dump_cid(const struct mmc_cid *cid)
+{
+ printf("Manufacturer ID: %02lX\n", cid->mid);
+ printf("OEM/Application ID: %04lX\n", cid->oid);
+ printf("Product name: %s\n", cid->pnm);
+ printf("Product Revision: %lu.%lu\n",
+ cid->prv >> 4, cid->prv & 0x0f);
+ printf("Product Serial Number: %lu\n", cid->psn);
+ printf("Manufacturing Date: %02lu/%02lu\n",
+ cid->mdt >> 4, cid->mdt & 0x0f);
+}
+
+static void mmc_dump_csd(const struct mmc_csd *csd)
+{
+ unsigned long *csd_raw = (unsigned long *)csd;
+ printf("CSD data: %08lx %08lx %08lx %08lx\n",
+ csd_raw[0], csd_raw[1], csd_raw[2], csd_raw[3]);
+ printf("CSD structure version: 1.%u\n", csd->csd_structure);
+ printf("MMC System Spec version: %u\n", csd->spec_vers);
+ printf("Card command classes: %03x\n", csd->ccc);
+ printf("Read block length: %u\n", 1 << csd->read_bl_len);
+ if (csd->read_bl_partial)
+ puts("Supports partial reads\n");
+ else
+ puts("Does not support partial reads\n");
+ printf("Write block length: %u\n", 1 << csd->write_bl_len);
+ if (csd->write_bl_partial)
+ puts("Supports partial writes\n");
+ else
+ puts("Does not support partial writes\n");
+ if (csd->wp_grp_enable)
+ printf("Supports group WP: %u\n", csd->wp_grp_size + 1);
+ else
+ puts("Does not support group WP\n");
+ printf("Card capacity: %u bytes\n",
+ (csd->c_size + 1) * (1 << (csd->c_size_mult + 2)) *
+ (1 << csd->read_bl_len));
+ printf("File format: %u/%u\n",
+ csd->file_format_grp, csd->file_format);
+ puts("Write protection: ");
+ if (csd->perm_write_protect)
+ puts(" permanent");
+ if (csd->tmp_write_protect)
+ puts(" temporary");
+ putc('\n');
+}
+
+static int mmc_idle_cards(void)
+{
+ int ret;
+
+ /* Reset and initialize all cards */
+ ret = mmc_cmd(MMC_CMD_GO_IDLE_STATE, 0, NULL, 0);
+ if (ret)
+ return ret;
+
+ /* Keep the bus idle for 74 clock cycles */
+ return mmc_cmd(0, 0, NULL, INIT_CMD);
+}
+
+static int sd_init_card(struct mmc_cid *cid, int verbose)
+{
+ unsigned long resp[4];
+ int i, ret = 0;
+
+ mmc_idle_cards();
+ for (i = 0; i < 1000; i++) {
+ ret = mmc_acmd(MMC_ACMD_SD_SEND_OP_COND, CFG_MMC_OP_COND,
+ resp, R3 | NID);
+ if (ret || (resp[0] & 0x80000000))
+ break;
+ ret = -ETIMEDOUT;
+ }
+
+ if (ret)
+ return ret;
+
+ ret = mmc_cmd(MMC_CMD_ALL_SEND_CID, 0, resp, R2 | NID);
+ if (ret)
+ return ret;
+ sd_parse_cid(cid, resp);
+ if (verbose)
+ mmc_dump_cid(cid);
+
+ /* Get RCA of the card that responded */
+ ret = mmc_cmd(MMC_CMD_SD_SEND_RELATIVE_ADDR, 0, resp, R6 | NCR);
+ if (ret)
+ return ret;
+
+ mmc_rca = resp[0] >> 16;
+ if (verbose)
+ printf("SD Card detected (RCA %u)\n", mmc_rca);
+ return 0;
+}
+
+static int mmc_init_card(struct mmc_cid *cid, int verbose)
+{
+ unsigned long resp[4];
+ int i, ret = 0;
+
+ mmc_idle_cards();
+ for (i = 0; i < 1000; i++) {
+ ret = mmc_cmd(MMC_CMD_SEND_OP_COND, CFG_MMC_OP_COND, resp,
+ R3 | NID | OPEN_DRAIN);
+ if (ret || (resp[0] & 0x80000000))
+ break;
+ ret = -ETIMEDOUT;
+ }
+
+ if (ret)
+ return ret;
+
+ /* Get CID of all cards. FIXME: Support more than one card */
+ ret = mmc_cmd(MMC_CMD_ALL_SEND_CID, 0, resp, R2 | NID | OPEN_DRAIN);
+ if (ret)
+ return ret;
+ mmc_parse_cid(cid, resp);
+ if (verbose)
+ mmc_dump_cid(cid);
+
+ /* Set Relative Address of the card that responded */
+ ret = mmc_cmd(MMC_CMD_SET_RELATIVE_ADDR, mmc_rca << 16, resp,
+ R1 | NCR | OPEN_DRAIN);
+ return ret;
+}
+
+int mmc_init(int verbose)
+{
+ struct mmc_cid cid;
+ struct mmc_csd csd;
+ int ret;
+
+ /* Initialize controller */
+ mmci_writel(CR, MMCI_BIT(SWRST));
+ mmci_writel(CR, MMCI_BIT(MCIEN));
+ mmci_writel(DTOR, 0x5f);
+ mmci_writel(IDR, ~0UL);
+ mci_set_mode(CFG_MMC_CLK_OD, MMC_DEFAULT_BLKLEN);
+
+ ret = sd_init_card(&cid, verbose);
+ if (ret) {
+ mmc_rca = MMC_DEFAULT_RCA;
+ ret = mmc_init_card(&cid, verbose);
+ }
+ if (ret)
+ return ret;
+
+ /* Get CSD from the card */
+ ret = mmc_cmd(MMC_CMD_SEND_CSD, mmc_rca << 16, &csd, R2 | NCR);
+ if (ret)
+ return ret;
+ if (verbose)
+ mmc_dump_csd(&csd);
+
+ /* Initialize the blockdev structure */
+ mmc_blkdev.if_type = IF_TYPE_MMC;
+ mmc_blkdev.part_type = PART_TYPE_DOS;
+ mmc_blkdev.block_read = mmc_bread;
+ sprintf((char *)mmc_blkdev.vendor,
+ "Man %02x%04x Snr %08x",
+ cid.mid, cid.oid, cid.psn);
+ strncpy((char *)mmc_blkdev.product, cid.pnm,
+ sizeof(mmc_blkdev.product));
+ sprintf((char *)mmc_blkdev.revision, "%x %x",
+ cid.prv >> 4, cid.prv & 0x0f);
+ mmc_blkdev.blksz = 1 << csd.read_bl_len;
+ mmc_blkdev.lba = (csd.c_size + 1) * (1 << (csd.c_size_mult + 2));
+
+ mci_set_mode(CFG_MMC_CLK_PP, mmc_blkdev.blksz);
+
+#if 0
+ if (fat_register_device(&mmc_blkdev, 1))
+ printf("Could not register MMC fat device\n");
+#else
+ init_part(&mmc_blkdev);
+#endif
+
+ return 0;
+}
+
+int mmc_read(ulong src, uchar *dst, int size)
+{
+ return -ENOSYS;
+}
+
+int mmc_write(uchar *src, ulong dst, int size)
+{
+ return -ENOSYS;
+}
+
+int mmc2info(ulong addr)
+{
+ return 0;
+}
+
+#endif /* CONFIG_MMC */
diff --git a/cpu/at32ap/atmel_mci.h b/cpu/at32ap/atmel_mci.h
new file mode 100644
index 0000000..0ffbc4f
--- /dev/null
+++ b/cpu/at32ap/atmel_mci.h
@@ -0,0 +1,197 @@
+/*
+ * Copyright (C) 2005-2006 Atmel Corporation
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef __CPU_AT32AP_ATMEL_MCI_H__
+#define __CPU_AT32AP_ATMEL_MCI_H__
+
+/* Atmel MultiMedia Card Interface (MCI) registers */
+#define MMCI_CR 0x0000
+#define MMCI_MR 0x0004
+#define MMCI_DTOR 0x0008
+#define MMCI_SDCR 0x000c
+#define MMCI_ARGR 0x0010
+#define MMCI_CMDR 0x0014
+#define MMCI_RSPR 0x0020
+#define MMCI_RSPR1 0x0024
+#define MMCI_RSPR2 0x0028
+#define MMCI_RSPR3 0x002c
+#define MMCI_RDR 0x0030
+#define MMCI_TDR 0x0034
+#define MMCI_SR 0x0040
+#define MMCI_IER 0x0044
+#define MMCI_IDR 0x0048
+#define MMCI_IMR 0x004c
+
+/* Bitfields in CR */
+#define MMCI_MCIEN_OFFSET 0
+#define MMCI_MCIEN_SIZE 1
+#define MMCI_MCIDIS_OFFSET 1
+#define MMCI_MCIDIS_SIZE 1
+#define MMCI_PWSEN_OFFSET 2
+#define MMCI_PWSEN_SIZE 1
+#define MMCI_PWSDIS_OFFSET 3
+#define MMCI_PWSDIS_SIZE 1
+#define MMCI_SWRST_OFFSET 7
+#define MMCI_SWRST_SIZE 1
+
+/* Bitfields in MR */
+#define MMCI_CLKDIV_OFFSET 0
+#define MMCI_CLKDIV_SIZE 8
+#define MMCI_PWSDIV_OFFSET 8
+#define MMCI_PWSDIV_SIZE 3
+#define MMCI_PDCPADV_OFFSET 14
+#define MMCI_PDCPADV_SIZE 1
+#define MMCI_PDCMODE_OFFSET 15
+#define MMCI_PDCMODE_SIZE 1
+#define MMCI_BLKLEN_OFFSET 16
+#define MMCI_BLKLEN_SIZE 16
+
+/* Bitfields in DTOR */
+#define MMCI_DTOCYC_OFFSET 0
+#define MMCI_DTOCYC_SIZE 4
+#define MMCI_DTOMUL_OFFSET 4
+#define MMCI_DTOMUL_SIZE 3
+
+/* Bitfields in SDCR */
+#define MMCI_SCDSEL_OFFSET 0
+#define MMCI_SCDSEL_SIZE 4
+#define MMCI_SCDBUS_OFFSET 7
+#define MMCI_SCDBUS_SIZE 1
+
+/* Bitfields in ARGR */
+#define MMCI_ARG_OFFSET 0
+#define MMCI_ARG_SIZE 32
+
+/* Bitfields in CMDR */
+#define MMCI_CMDNB_OFFSET 0
+#define MMCI_CMDNB_SIZE 6
+#define MMCI_RSPTYP_OFFSET 6
+#define MMCI_RSPTYP_SIZE 2
+#define MMCI_SPCMD_OFFSET 8
+#define MMCI_SPCMD_SIZE 3
+#define MMCI_OPDCMD_OFFSET 11
+#define MMCI_OPDCMD_SIZE 1
+#define MMCI_MAXLAT_OFFSET 12
+#define MMCI_MAXLAT_SIZE 1
+#define MMCI_TRCMD_OFFSET 16
+#define MMCI_TRCMD_SIZE 2
+#define MMCI_TRDIR_OFFSET 18
+#define MMCI_TRDIR_SIZE 1
+#define MMCI_TRTYP_OFFSET 19
+#define MMCI_TRTYP_SIZE 2
+
+/* Bitfields in RSPRx */
+#define MMCI_RSP_OFFSET 0
+#define MMCI_RSP_SIZE 32
+
+/* Bitfields in SR/IER/IDR/IMR */
+#define MMCI_CMDRDY_OFFSET 0
+#define MMCI_CMDRDY_SIZE 1
+#define MMCI_RXRDY_OFFSET 1
+#define MMCI_RXRDY_SIZE 1
+#define MMCI_TXRDY_OFFSET 2
+#define MMCI_TXRDY_SIZE 1
+#define MMCI_BLKE_OFFSET 3
+#define MMCI_BLKE_SIZE 1
+#define MMCI_DTIP_OFFSET 4
+#define MMCI_DTIP_SIZE 1
+#define MMCI_NOTBUSY_OFFSET 5
+#define MMCI_NOTBUSY_SIZE 1
+#define MMCI_ENDRX_OFFSET 6
+#define MMCI_ENDRX_SIZE 1
+#define MMCI_ENDTX_OFFSET 7
+#define MMCI_ENDTX_SIZE 1
+#define MMCI_RXBUFF_OFFSET 14
+#define MMCI_RXBUFF_SIZE 1
+#define MMCI_TXBUFE_OFFSET 15
+#define MMCI_TXBUFE_SIZE 1
+#define MMCI_RINDE_OFFSET 16
+#define MMCI_RINDE_SIZE 1
+#define MMCI_RDIRE_OFFSET 17
+#define MMCI_RDIRE_SIZE 1
+#define MMCI_RCRCE_OFFSET 18
+#define MMCI_RCRCE_SIZE 1
+#define MMCI_RENDE_OFFSET 19
+#define MMCI_RENDE_SIZE 1
+#define MMCI_RTOE_OFFSET 20
+#define MMCI_RTOE_SIZE 1
+#define MMCI_DCRCE_OFFSET 21
+#define MMCI_DCRCE_SIZE 1
+#define MMCI_DTOE_OFFSET 22
+#define MMCI_DTOE_SIZE 1
+#define MMCI_OVRE_OFFSET 30
+#define MMCI_OVRE_SIZE 1
+#define MMCI_UNRE_OFFSET 31
+#define MMCI_UNRE_SIZE 1
+
+/* Constants for DTOMUL */
+#define MMCI_DTOMUL_1_CYCLE 0
+#define MMCI_DTOMUL_16_CYCLES 1
+#define MMCI_DTOMUL_128_CYCLES 2
+#define MMCI_DTOMUL_256_CYCLES 3
+#define MMCI_DTOMUL_1024_CYCLES 4
+#define MMCI_DTOMUL_4096_CYCLES 5
+#define MMCI_DTOMUL_65536_CYCLES 6
+#define MMCI_DTOMUL_1048576_CYCLES 7
+
+/* Constants for RSPTYP */
+#define MMCI_RSPTYP_NO_RESP 0
+#define MMCI_RSPTYP_48_BIT_RESP 1
+#define MMCI_RSPTYP_136_BIT_RESP 2
+
+/* Constants for SPCMD */
+#define MMCI_SPCMD_NO_SPEC_CMD 0
+#define MMCI_SPCMD_INIT_CMD 1
+#define MMCI_SPCMD_SYNC_CMD 2
+#define MMCI_SPCMD_INT_CMD 4
+#define MMCI_SPCMD_INT_RESP 5
+
+/* Constants for TRCMD */
+#define MMCI_TRCMD_NO_TRANS 0
+#define MMCI_TRCMD_START_TRANS 1
+#define MMCI_TRCMD_STOP_TRANS 2
+
+/* Constants for TRTYP */
+#define MMCI_TRTYP_BLOCK 0
+#define MMCI_TRTYP_MULTI_BLOCK 1
+#define MMCI_TRTYP_STREAM 2
+
+/* Bit manipulation macros */
+#define MMCI_BIT(name) \
+ (1 << MMCI_##name##_OFFSET)
+#define MMCI_BF(name,value) \
+ (((value) & ((1 << MMCI_##name##_SIZE) - 1)) \
+ << MMCI_##name##_OFFSET)
+#define MMCI_BFEXT(name,value) \
+ (((value) >> MMCI_##name##_OFFSET)\
+ & ((1 << MMCI_##name##_SIZE) - 1))
+#define MMCI_BFINS(name,value,old) \
+ (((old) & ~(((1 << MMCI_##name##_SIZE) - 1) \
+ << MMCI_##name##_OFFSET)) \
+ | MMCI_BF(name,value))
+
+/* Register access macros */
+#define mmci_readl(reg) \
+ readl((void *)MMCI_BASE + MMCI_##reg)
+#define mmci_writel(reg,value) \
+ writel((value), (void *)MMCI_BASE + MMCI_##reg)
+
+#endif /* __CPU_AT32AP_ATMEL_MCI_H__ */
diff --git a/cpu/at32ap/cpu.c b/cpu/at32ap/cpu.c
index 37e3ea0..311466b 100644
--- a/cpu/at32ap/cpu.c
+++ b/cpu/at32ap/cpu.c
@@ -26,33 +26,79 @@
#include <asm/sections.h>
#include <asm/sysreg.h>
+#include <asm/arch/clk.h>
#include <asm/arch/memory-map.h>
-#include <asm/arch/platform.h>
#include "hsmc3.h"
+#include "sm.h"
+
+/* Sanity checks */
+#if (CFG_CLKDIV_CPU > CFG_CLKDIV_HSB) \
+ || (CFG_CLKDIV_HSB > CFG_CLKDIV_PBA) \
+ || (CFG_CLKDIV_HSB > CFG_CLKDIV_PBB)
+# error Constraint fCPU >= fHSB >= fPB{A,B} violated
+#endif
+#if defined(CONFIG_PLL) && ((CFG_PLL0_MUL < 1) || (CFG_PLL0_DIV < 1))
+# error Invalid PLL multiplier and/or divider
+#endif
DECLARE_GLOBAL_DATA_PTR;
+static void pm_init(void)
+{
+ uint32_t cksel;
+
+#ifdef CONFIG_PLL
+ /* Initialize the PLL */
+ sm_writel(PM_PLL0, (SM_BF(PLLCOUNT, CFG_PLL0_SUPPRESS_CYCLES)
+ | SM_BF(PLLMUL, CFG_PLL0_MUL - 1)
+ | SM_BF(PLLDIV, CFG_PLL0_DIV - 1)
+ | SM_BF(PLLOPT, CFG_PLL0_OPT)
+ | SM_BF(PLLOSC, 0)
+ | SM_BIT(PLLEN)));
+
+ /* Wait for lock */
+ while (!(sm_readl(PM_ISR) & SM_BIT(LOCK0))) ;
+#endif
+
+ /* Set up clocks for the CPU and all peripheral buses */
+ cksel = 0;
+ if (CFG_CLKDIV_CPU)
+ cksel |= SM_BIT(CPUDIV) | SM_BF(CPUSEL, CFG_CLKDIV_CPU - 1);
+ if (CFG_CLKDIV_HSB)
+ cksel |= SM_BIT(HSBDIV) | SM_BF(HSBSEL, CFG_CLKDIV_HSB - 1);
+ if (CFG_CLKDIV_PBA)
+ cksel |= SM_BIT(PBADIV) | SM_BF(PBASEL, CFG_CLKDIV_PBA - 1);
+ if (CFG_CLKDIV_PBB)
+ cksel |= SM_BIT(PBBDIV) | SM_BF(PBBSEL, CFG_CLKDIV_PBB - 1);
+ sm_writel(PM_CKSEL, cksel);
+
+ gd->cpu_hz = get_cpu_clk_rate();
+
+#ifdef CONFIG_PLL
+ /* Use PLL0 as main clock */
+ sm_writel(PM_MCCTRL, SM_BIT(PLLSEL));
+#endif
+}
+
int cpu_init(void)
{
- const struct device *hebi;
extern void _evba(void);
char *p;
gd->cpu_hz = CFG_OSC0_HZ;
- /* fff03400: 00010001 04030402 00050005 10011103 */
- hebi = get_device(DEVICE_HEBI);
- hsmc3_writel(hebi, MODE0, 0x00031103);
- hsmc3_writel(hebi, CYCLE0, 0x000c000d);
- hsmc3_writel(hebi, PULSE0, 0x0b0a0906);
- hsmc3_writel(hebi, SETUP0, 0x00010002);
+ /* TODO: Move somewhere else, but needs to be run before we
+ * increase the clock frequency. */
+ hsmc3_writel(MODE0, 0x00031103);
+ hsmc3_writel(CYCLE0, 0x000c000d);
+ hsmc3_writel(PULSE0, 0x0b0a0906);
+ hsmc3_writel(SETUP0, 0x00010002);
pm_init();
sysreg_write(EVBA, (unsigned long)&_evba);
asm volatile("csrf %0" : : "i"(SYSREG_EM_OFFSET));
- gd->console_uart = get_device(CFG_CONSOLE_UART_DEV);
/* Lock everything that mess with the flash in the icache */
for (p = __flashprog_start; p <= (__flashprog_end + CFG_ICACHE_LINESZ);
diff --git a/cpu/at32ap/device.c b/cpu/at32ap/device.c
deleted file mode 100644
index 89914b6..0000000
--- a/cpu/at32ap/device.c
+++ /dev/null
@@ -1,126 +0,0 @@
-/*
- * Copyright (C) 2006 Atmel Corporation
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-#include <common.h>
-
-#include <asm/arch/platform.h>
-
-#include "sm.h"
-
-struct device_state {
- int refcount;
-};
-
-static struct device_state device_state[NR_DEVICES];
-
-static int claim_resource(const struct resource *res)
-{
- int ret = 0;
-
- switch (res->type) {
- case RESOURCE_GPIO:
- ret = gpio_set_func(res->u.gpio.gpio_dev,
- res->u.gpio.start,
- res->u.gpio.nr_pins,
- res->u.gpio.func);
- break;
- case RESOURCE_CLOCK:
- ret = pm_enable_clock(res->u.clock.id, res->u.clock.index);
- break;
- }
-
- return ret;
-}
-
-static void free_resource(const struct resource *res)
-{
- switch (res->type) {
- case RESOURCE_GPIO:
- gpio_free(res->u.gpio.gpio_dev, res->u.gpio.start,
- res->u.gpio.nr_pins);
- break;
- case RESOURCE_CLOCK:
- pm_disable_clock(res->u.clock.id, res->u.clock.index);
- break;
- }
-}
-
-static int init_dev(const struct device *dev)
-{
- unsigned int i;
- int ret = 0;
-
- for (i = 0; i < dev->nr_resources; i++) {
- ret = claim_resource(&dev->resource[i]);
- if (ret)
- goto cleanup;
- }
-
- return 0;
-
-cleanup:
- while (i--)
- free_resource(&dev->resource[i]);
-
- return ret;
-}
-
-const struct device *get_device(enum device_id devid)
-{
- struct device_state *devstate;
- const struct device *dev;
- unsigned long flags;
- int initialized = 0;
- int ret = 0;
-
- devstate = &device_state[devid];
- dev = &chip_device[devid];
-
- flags = disable_interrupts();
- if (devstate->refcount++)
- initialized = 1;
- if (flags)
- enable_interrupts();
-
- if (!initialized)
- ret = init_dev(dev);
-
- return ret ? NULL : dev;
-}
-
-void put_device(const struct device *dev)
-{
- struct device_state *devstate;
- unsigned long devid, flags;
-
- devid = (unsigned long)(dev - chip_device) / sizeof(struct device);
- devstate = &device_state[devid];
-
- flags = disable_interrupts();
- devstate--;
- if (!devstate) {
- unsigned int i;
- for (i = 0; i < dev->nr_resources; i++)
- free_resource(&dev->resource[i]);
- }
- if (flags)
- enable_interrupts();
-}
diff --git a/cpu/at32ap/entry.S b/cpu/at32ap/entry.S
index b52d798..a6fc688 100644
--- a/cpu/at32ap/entry.S
+++ b/cpu/at32ap/entry.S
@@ -42,8 +42,7 @@
* We're running at interrupt level 3, so we don't need to save
* r8-r12 or lr to the stack.
*/
- mov r8, lo(timer_overflow)
- orh r8, hi(timer_overflow)
+ lda.w r8, timer_overflow
ld.w r9, r8[0]
mov r10, -1
mtsr SYSREG_COMPARE, r10
diff --git a/cpu/at32ap/exception.c b/cpu/at32ap/exception.c
index 4123c44..0672685 100644
--- a/cpu/at32ap/exception.c
+++ b/cpu/at32ap/exception.c
@@ -24,6 +24,8 @@
#include <asm/sysreg.h>
#include <asm/ptrace.h>
+DECLARE_GLOBAL_DATA_PTR;
+
static const char * const cpu_modes[8] = {
"Application", "Supervisor", "Interrupt level 0", "Interrupt level 1",
"Interrupt level 2", "Interrupt level 3", "Exception", "NMI"
@@ -109,11 +111,10 @@
printf("CPU Mode: %s\n", cpu_modes[mode]);
/* Avoid exception loops */
- if (regs->sp >= CFG_INIT_SP_ADDR
- || regs->sp < (CFG_INIT_SP_ADDR - CONFIG_STACKSIZE))
+ if (regs->sp < CFG_SDRAM_BASE || regs->sp >= gd->stack_end)
printf("\nStack pointer seems bogus, won't do stack dump\n");
else
- dump_mem("\nStack: ", regs->sp, CFG_INIT_SP_ADDR);
+ dump_mem("\nStack: ", regs->sp, gd->stack_end);
panic("Unhandled exception\n");
}
diff --git a/cpu/at32ap/hsdramc.c b/cpu/at32ap/hsdramc.c
index f36da35..a936e03 100644
--- a/cpu/at32ap/hsdramc.c
+++ b/cpu/at32ap/hsdramc.c
@@ -25,17 +25,11 @@
#include <asm/io.h>
#include <asm/sdram.h>
-#include <asm/arch/platform.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/memory-map.h>
#include "hsdramc1.h"
-struct hsdramc {
- const struct device *hebi;
- void *regs;
-};
-
-static struct hsdramc hsdramc;
-
unsigned long sdram_init(const struct sdram_info *info)
{
unsigned long *sdram = (unsigned long *)uncached(info->phys_addr);
@@ -44,16 +38,6 @@
unsigned long bus_hz;
unsigned int i;
- hsdramc.hebi = get_device(DEVICE_HEBI);
- if (!hsdramc.hebi)
- return 0;
-
- /* FIXME: Both of these lines are complete hacks */
- hsdramc.regs = hsdramc.hebi->regs + 0x400;
- bus_hz = pm_get_clock_freq(hsdramc.hebi->resource[0].u.clock.id);
-
- cpu_enable_sdram();
-
tmp = (HSDRAMC1_BF(NC, info->col_bits - 8)
| HSDRAMC1_BF(NR, info->row_bits - 11)
| HSDRAMC1_BF(NB, info->bank_bits - 1)
@@ -74,7 +58,7 @@
+ info->bank_bits + 2);
#endif
- hsdramc1_writel(&hsdramc, CR, tmp);
+ hsdramc1_writel(CR, tmp);
/*
* Initialization sequence for SDRAM, from the data sheet:
@@ -87,15 +71,15 @@
/*
* 2. A Precharge All command is issued to the SDRAM
*/
- hsdramc1_writel(&hsdramc, MR, HSDRAMC1_MODE_BANKS_PRECHARGE);
- hsdramc1_readl(&hsdramc, MR);
+ hsdramc1_writel(MR, HSDRAMC1_MODE_BANKS_PRECHARGE);
+ hsdramc1_readl(MR);
writel(0, sdram);
/*
* 3. Eight auto-refresh (CBR) cycles are provided
*/
- hsdramc1_writel(&hsdramc, MR, HSDRAMC1_MODE_AUTO_REFRESH);
- hsdramc1_readl(&hsdramc, MR);
+ hsdramc1_writel(MR, HSDRAMC1_MODE_AUTO_REFRESH);
+ hsdramc1_readl(MR);
for (i = 0; i < 8; i++)
writel(0, sdram);
@@ -106,8 +90,8 @@
*
* CAS from info struct, burst length 1, serial burst type
*/
- hsdramc1_writel(&hsdramc, MR, HSDRAMC1_MODE_LOAD_MODE);
- hsdramc1_readl(&hsdramc, MR);
+ hsdramc1_writel(MR, HSDRAMC1_MODE_LOAD_MODE);
+ hsdramc1_readl(MR);
writel(0, sdram + (info->cas << 4));
/*
@@ -117,9 +101,9 @@
* From the timing diagram, it looks like tMRD is 3
* cycles...try a dummy read from the peripheral bus.
*/
- hsdramc1_readl(&hsdramc, MR);
- hsdramc1_writel(&hsdramc, MR, HSDRAMC1_MODE_NORMAL);
- hsdramc1_readl(&hsdramc, MR);
+ hsdramc1_readl(MR);
+ hsdramc1_writel(MR, HSDRAMC1_MODE_NORMAL);
+ hsdramc1_readl(MR);
writel(0, sdram);
/*
@@ -128,7 +112,8 @@
*
* 15.6 us is a typical value for a burst of length one
*/
- hsdramc1_writel(&hsdramc, TR, (156 * (bus_hz / 1000)) / 10000);
+ bus_hz = get_sdram_clk_rate();
+ hsdramc1_writel(TR, (156 * (bus_hz / 1000)) / 10000);
printf("SDRAM: %u MB at address 0x%08lx\n",
sdram_size >> 20, info->phys_addr);
diff --git a/cpu/at32ap/hsdramc1.h b/cpu/at32ap/hsdramc1.h
index ce229bc..305d2cb 100644
--- a/cpu/at32ap/hsdramc1.h
+++ b/cpu/at32ap/hsdramc1.h
@@ -135,9 +135,9 @@
| HSDRAMC1_BF(name,value))
/* Register access macros */
-#define hsdramc1_readl(port,reg) \
- readl((port)->regs + HSDRAMC1_##reg)
-#define hsdramc1_writel(port,reg,value) \
- writel((value), (port)->regs + HSDRAMC1_##reg)
+#define hsdramc1_readl(reg) \
+ readl((void *)HSDRAMC_BASE + HSDRAMC1_##reg)
+#define hsdramc1_writel(reg,value) \
+ writel((value), (void *)HSDRAMC_BASE + HSDRAMC1_##reg)
#endif /* __ASM_AVR32_HSDRAMC1_H__ */
diff --git a/cpu/at32ap/hsmc3.h b/cpu/at32ap/hsmc3.h
index ec78cee..ca533b9 100644
--- a/cpu/at32ap/hsmc3.h
+++ b/cpu/at32ap/hsmc3.h
@@ -118,9 +118,9 @@
| HSMC3_BF(name,value))
/* Register access macros */
-#define hsmc3_readl(port,reg) \
- readl((port)->regs + HSMC3_##reg)
-#define hsmc3_writel(port,reg,value) \
- writel((value), (port)->regs + HSMC3_##reg)
+#define hsmc3_readl(reg) \
+ readl((void *)HSMC_BASE + HSMC3_##reg)
+#define hsmc3_writel(reg,value) \
+ writel((value), (void *)HSMC_BASE + HSMC3_##reg)
#endif /* __CPU_AT32AP_HSMC3_H__ */
diff --git a/cpu/at32ap/interrupts.c b/cpu/at32ap/interrupts.c
index d720cfa..c9e0499 100644
--- a/cpu/at32ap/interrupts.c
+++ b/cpu/at32ap/interrupts.c
@@ -27,7 +27,7 @@
#include <asm/processor.h>
#include <asm/sysreg.h>
-#include <asm/arch/platform.h>
+#include <asm/arch/memory-map.h>
#define HANDLER_MASK 0x00ffffff
#define INTLEV_SHIFT 30
@@ -44,8 +44,6 @@
*/
static unsigned long tb_factor;
-static const struct device *intc_dev;
-
unsigned long get_tbclk(void)
{
return gd->cpu_hz;
@@ -117,16 +115,19 @@
static int set_interrupt_handler(unsigned int nr, void (*handler)(void),
unsigned int priority)
{
+ extern void _evba(void);
unsigned long intpr;
unsigned long handler_addr = (unsigned long)handler;
+ handler_addr -= (unsigned long)&_evba;
+
if ((handler_addr & HANDLER_MASK) != handler_addr
|| (priority & INTLEV_MASK) != priority)
return -EINVAL;
intpr = (handler_addr & HANDLER_MASK);
intpr |= (priority & INTLEV_MASK) << INTLEV_SHIFT;
- writel(intpr, intc_dev->regs + 4 * nr);
+ writel(intpr, (void *)INTC_BASE + 4 * nr);
return 0;
}
@@ -143,10 +144,7 @@
do_div(tmp, gd->cpu_hz);
tb_factor = (u32)tmp;
- intc_dev = get_device(DEVICE_INTC);
-
- if (!intc_dev
- || set_interrupt_handler(0, &timer_interrupt_handler, 3))
+ if (set_interrupt_handler(0, &timer_interrupt_handler, 3))
return;
/* For all practical purposes, this gives us an overflow interrupt */
diff --git a/cpu/at32ap/pio.c b/cpu/at32ap/pio.c
index 8b6c3a3..9ba0b8e 100644
--- a/cpu/at32ap/pio.c
+++ b/cpu/at32ap/pio.c
@@ -21,74 +21,40 @@
*/
#include <common.h>
-#include <asm/errno.h>
#include <asm/io.h>
-#include <asm/arch/platform.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/memory-map.h>
#include "pio2.h"
-struct pio_state {
- const struct device *dev;
- u32 alloc_mask;
-};
-
-static struct pio_state pio_state[CFG_NR_PIOS];
-
-int gpio_set_func(enum device_id gpio_devid, unsigned int start,
- unsigned int nr_pins, enum gpio_func func)
+void gpio_select_periph_A(unsigned int pin, int use_pullup)
{
- const struct device *gpio;
- struct pio_state *state;
- u32 mask;
+ void *base = gpio_pin_to_addr(pin);
+ uint32_t mask = 1 << (pin & 0x1f);
- state = &pio_state[gpio_devid - DEVICE_PIOA];
+ if (!base)
+ panic("Invalid GPIO pin %u\n", pin);
- gpio = get_device(gpio_devid);
- if (!gpio)
- return -EBUSY;
-
- state->dev = gpio;
- mask = ((1 << nr_pins) - 1) << start;
-
- if (mask & state->alloc_mask) {
- put_device(gpio);
- return -EBUSY;
- }
- state->alloc_mask |= mask;
-
- switch (func) {
- case GPIO_FUNC_GPIO:
- /* TODO */
- return -EINVAL;
- case GPIO_FUNC_A:
- pio2_writel(gpio, ASR, mask);
- pio2_writel(gpio, PDR, mask);
- pio2_writel(gpio, PUDR, mask);
- break;
- case GPIO_FUNC_B:
- pio2_writel(gpio, BSR, mask);
- pio2_writel(gpio, PDR, mask);
- pio2_writel(gpio, PUDR, mask);
- break;
- }
-
- return 0;
+ pio2_writel(base, ASR, mask);
+ pio2_writel(base, PDR, mask);
+ if (use_pullup)
+ pio2_writel(base, PUER, mask);
+ else
+ pio2_writel(base, PUDR, mask);
}
-void gpio_free(enum device_id gpio_devid, unsigned int start,
- unsigned int nr_pins)
+void gpio_select_periph_B(unsigned int pin, int use_pullup)
{
- const struct device *gpio;
- struct pio_state *state;
- u32 mask;
+ void *base = gpio_pin_to_addr(pin);
+ uint32_t mask = 1 << (pin & 0x1f);
- state = &pio_state[gpio_devid - DEVICE_PIOA];
- gpio = state->dev;
- mask = ((1 << nr_pins) - 1) << start;
-
- pio2_writel(gpio, ODR, mask);
- pio2_writel(gpio, PER, mask);
+ if (!base)
+ panic("Invalid GPIO pin %u\n", pin);
- state->alloc_mask &= ~mask;
- put_device(gpio);
+ pio2_writel(base, BSR, mask);
+ pio2_writel(base, PDR, mask);
+ if (use_pullup)
+ pio2_writel(base, PUER, mask);
+ else
+ pio2_writel(base, PUDR, mask);
}
diff --git a/cpu/at32ap/pio2.h b/cpu/at32ap/pio2.h
index 6b79de3..9719ea8 100644
--- a/cpu/at32ap/pio2.h
+++ b/cpu/at32ap/pio2.h
@@ -36,9 +36,9 @@
#define PIO2_OWSR 0x00a8
/* Register access macros */
-#define pio2_readl(port,reg) \
- readl((port)->regs + PIO2_##reg)
-#define pio2_writel(port,reg,value) \
- writel((value), (port)->regs + PIO2_##reg)
+#define pio2_readl(base,reg) \
+ readl((void *)base + PIO2_##reg)
+#define pio2_writel(base,reg,value) \
+ writel((value), (void *)base + PIO2_##reg)
#endif /* __CPU_AT32AP_PIO2_H__ */
diff --git a/cpu/at32ap/pm.c b/cpu/at32ap/pm.c
index 01ac325..c78d547 100644
--- a/cpu/at32ap/pm.c
+++ b/cpu/at32ap/pm.c
@@ -26,138 +26,17 @@
#include <asm/io.h>
#include <asm/arch/memory-map.h>
-#include <asm/arch/platform.h>
#include "sm.h"
-/* Sanity checks */
-#if (CFG_CLKDIV_CPU > CFG_CLKDIV_HSB) \
- || (CFG_CLKDIV_HSB > CFG_CLKDIV_PBA) \
- || (CFG_CLKDIV_HSB > CFG_CLKDIV_PBB)
-# error Constraint fCPU >= fHSB >= fPB{A,B} violated
-#endif
-#if defined(CONFIG_PLL) && ((CFG_PLL0_MUL < 1) || (CFG_PLL0_DIV < 1))
-# error Invalid PLL multiplier and/or divider
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-struct clock_domain_state {
- const struct device *bridge;
- unsigned long freq;
- u32 mask;
-};
-static struct clock_domain_state ckd_state[NR_CLOCK_DOMAINS];
-
-int pm_enable_clock(enum clock_domain_id id, unsigned int index)
-{
- const struct clock_domain *ckd = &chip_clock[id];
- struct clock_domain_state *state = &ckd_state[id];
-
- if (ckd->bridge != NO_DEVICE) {
- state->bridge = get_device(ckd->bridge);
- if (!state->bridge)
- return -EBUSY;
- }
-
- state->mask |= 1 << index;
- if (gd->sm)
- writel(state->mask, gd->sm->regs + ckd->reg);
-
- return 0;
-}
-
-void pm_disable_clock(enum clock_domain_id id, unsigned int index)
-{
- const struct clock_domain *ckd = &chip_clock[id];
- struct clock_domain_state *state = &ckd_state[id];
-
- state->mask &= ~(1 << index);
- if (gd->sm)
- writel(state->mask, gd->sm->regs + ckd->reg);
-
- if (ckd->bridge)
- put_device(state->bridge);
-}
-
-unsigned long pm_get_clock_freq(enum clock_domain_id domain)
-{
- return ckd_state[domain].freq;
-}
-
-void pm_init(void)
-{
- uint32_t cksel = 0;
- unsigned long main_clock;
-
- /* Make sure we don't disable any device we're already using */
- get_device(DEVICE_HRAMC);
- get_device(DEVICE_HEBI);
-
- /* Enable the PICO as well */
- ckd_state[CLOCK_CPU].mask |= 1;
-
- gd->sm = get_device(DEVICE_SM);
- if (!gd->sm)
- panic("Unable to claim system manager device!\n");
-
- /* Disable any devices that haven't been explicitly claimed */
- sm_writel(gd->sm, PM_PBB_MASK, ckd_state[CLOCK_PBB].mask);
- sm_writel(gd->sm, PM_PBA_MASK, ckd_state[CLOCK_PBA].mask);
- sm_writel(gd->sm, PM_HSB_MASK, ckd_state[CLOCK_HSB].mask);
- sm_writel(gd->sm, PM_CPU_MASK, ckd_state[CLOCK_CPU].mask);
#ifdef CONFIG_PLL
- /* Initialize the PLL */
- main_clock = (CFG_OSC0_HZ / CFG_PLL0_DIV) * CFG_PLL0_MUL;
-
- sm_writel(gd->sm, PM_PLL0, (SM_BF(PLLCOUNT, CFG_PLL0_SUPPRESS_CYCLES)
- | SM_BF(PLLMUL, CFG_PLL0_MUL - 1)
- | SM_BF(PLLDIV, CFG_PLL0_DIV - 1)
- | SM_BF(PLLOPT, CFG_PLL0_OPT)
- | SM_BF(PLLOSC, 0)
- | SM_BIT(PLLEN)));
-
- /* Wait for lock */
- while (!(sm_readl(gd->sm, PM_ISR) & SM_BIT(LOCK0))) ;
+#define MAIN_CLK_RATE ((CFG_OSC0_HZ / CFG_PLL0_DIV) * CFG_PLL0_MUL)
#else
- main_clock = CFG_OSC0_HZ;
+#define MAIN_CLK_RATE (CFG_OSC0_HZ)
#endif
- /* Set up clocks for the CPU and all peripheral buses */
- if (CFG_CLKDIV_CPU) {
- cksel |= SM_BIT(CPUDIV) | SM_BF(CPUSEL, CFG_CLKDIV_CPU - 1);
- ckd_state[CLOCK_CPU].freq = main_clock / (1 << CFG_CLKDIV_CPU);
- } else {
- ckd_state[CLOCK_CPU].freq = main_clock;
- }
- if (CFG_CLKDIV_HSB) {
- cksel |= SM_BIT(HSBDIV) | SM_BF(HSBSEL, CFG_CLKDIV_HSB - 1);
- ckd_state[CLOCK_HSB].freq = main_clock / (1 << CFG_CLKDIV_HSB);
- } else {
- ckd_state[CLOCK_HSB].freq = main_clock;
- }
- if (CFG_CLKDIV_PBA) {
- cksel |= SM_BIT(PBADIV) | SM_BF(PBASEL, CFG_CLKDIV_PBA - 1);
- ckd_state[CLOCK_PBA].freq = main_clock / (1 << CFG_CLKDIV_PBA);
- } else {
- ckd_state[CLOCK_PBA].freq = main_clock;
- }
- if (CFG_CLKDIV_PBB) {
- cksel |= SM_BIT(PBBDIV) | SM_BF(PBBSEL, CFG_CLKDIV_PBB - 1);
- ckd_state[CLOCK_PBB].freq = main_clock / (1 << CFG_CLKDIV_PBB);
- } else {
- ckd_state[CLOCK_PBB].freq = main_clock;
- }
- sm_writel(gd->sm, PM_CKSEL, cksel);
-
- /* CFG_HZ currently depends on cpu_hz */
- gd->cpu_hz = ckd_state[CLOCK_CPU].freq;
+DECLARE_GLOBAL_DATA_PTR;
-#ifdef CONFIG_PLL
- /* Use PLL0 as main clock */
- sm_writel(gd->sm, PM_MCCTRL, SM_BIT(PLLSEL));
-#endif
-}
#endif /* CFG_POWER_MANAGER */
diff --git a/cpu/at32ap/sm.h b/cpu/at32ap/sm.h
index ce81ef0..6492c8e 100644
--- a/cpu/at32ap/sm.h
+++ b/cpu/at32ap/sm.h
@@ -196,9 +196,9 @@
| SM_BF(name,value))
/* Register access macros */
-#define sm_readl(port,reg) \
- readl((port)->regs + SM_##reg)
-#define sm_writel(port,reg,value) \
- writel((value), (port)->regs + SM_##reg)
+#define sm_readl(reg) \
+ readl((void *)SM_BASE + SM_##reg)
+#define sm_writel(reg,value) \
+ writel((value), (void *)SM_BASE + SM_##reg)
#endif /* __CPU_AT32AP_SM_H__ */
diff --git a/cpu/at32ap/start.S b/cpu/at32ap/start.S
index 79ee33b..ab8c2b7 100644
--- a/cpu/at32ap/start.S
+++ b/cpu/at32ap/start.S
@@ -70,32 +70,12 @@
2: lddpc sp, sp_init
- /*
- * Relocate the data section and initialize .bss. Everything
- * is guaranteed to be at least doubleword aligned by the
- * linker script.
- */
- lddpc r12, .Ldata_vma
- lddpc r11, .Ldata_lma
- lddpc r10, .Ldata_end
- sub r10, r12
-4: ld.d r8, r11++
- sub r10, 8
- st.d r12++, r8
- brne 4b
-
- mov r8, 0
- mov r9, 0
- lddpc r10, .Lbss_end
- sub r10, r12
-4: sub r10, 8
- st.d r12++, r8
- brne 4b
-
/* Initialize the GOT pointer */
lddpc r6, got_init
3: rsub r6, pc
- ld.w pc, r6[start_u_boot@got]
+
+ /* Let's go */
+ rjmp board_init_f
.align 2
.type sp_init,@object
@@ -103,11 +83,82 @@
.long CFG_INIT_SP_ADDR
got_init:
.long 3b - _GLOBAL_OFFSET_TABLE_
+
+ /*
+ * void relocate_code(new_sp, new_gd, monitor_addr)
+ *
+ * Relocate the u-boot image into RAM and continue from there.
+ * Does not return.
+ */
+ .global relocate_code
+ .type relocate_code,@function
+relocate_code:
+ mov sp, r12 /* use new stack */
+ mov r12, r11 /* save new_gd */
+ mov r11, r10 /* save destination address */
+
+ /* copy .text section and flush the cache along the way */
+ lda.w r8, _text
+ lda.w r9, _etext
+ sub lr, r10, r8 /* relocation offset */
+
+1: ldm r8++, r0-r3
+ stm r10, r0-r3
+ sub r10, -16
+ ldm r8++, r0-r3
+ stm r10, r0-r3
+ sub r10, -16
+ cp.w r8, r9
+ cache r10[-4], 0x0d /* dcache clean/invalidate */
+ cache r10[-4], 0x01 /* icache invalidate */
+ brlt 1b
+
+ /* flush write buffer */
+ sync 0
+
+ /* copy data sections */
+ lda.w r9, _edata
+1: ld.d r0, r8++
+ st.d r10++, r0
+ cp.w r8, r9
+ brlt 1b
+
+ /* zero out .bss */
+ mov r0, 0
+ mov r1, 0
+ lda.w r9, _end
+ sub r9, r8
+1: st.d r10++, r0
+ sub r9, 8
+ brgt 1b
+
+ /* jump to RAM */
+ sub r0, pc, . - in_ram
+ add pc, r0, lr
+
+ .align 2
+in_ram:
+ /* find the new GOT and relocate it */
+ lddpc r6, got_init_reloc
+3: rsub r6, pc
+ mov r8, r6
+ lda.w r9, _egot
+ lda.w r10, _got
+ sub r9, r10
+1: ld.w r0, r8[0]
+ add r0, lr
+ st.w r8++, r0
+ sub r9, 4
+ brgt 1b
+
+ /* Move the exception handlers */
+ mfsr r2, SYSREG_EVBA
+ add r2, lr
+ mtsr SYSREG_EVBA, r2
+
+ /* Do the rest of the initialization sequence */
+ call board_init_r
+
+ .align 2
+got_init_reloc:
+ .long 3b - _GLOBAL_OFFSET_TABLE_
-.Ldata_lma:
- .long __data_lma
-.Ldata_vma:
- .long _data
-.Ldata_end:
- .long _edata
-.Lbss_end:
- .long _end
diff --git a/cpu/bf533/Makefile b/cpu/bf533/Makefile
index 90018f3..dd4f299 100644
--- a/cpu/bf533/Makefile
+++ b/cpu/bf533/Makefile
@@ -1,6 +1,6 @@
# U-boot - Makefile
#
-# Copyright (c) 2005 blackfin.uclinux.org
+# Copyright (c) 2005-2007 Analog Devices Inc.
#
# (C) Copyright 2000-2006
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -20,8 +20,8 @@
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
+# Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+# MA 02110-1301 USA
#
include $(TOPDIR)/config.mk
diff --git a/cpu/bf533/bf533_serial.h b/cpu/bf533/bf533_serial.h
index 0a04f3e..25b96a9 100644
--- a/cpu/bf533/bf533_serial.h
+++ b/cpu/bf533/bf533_serial.h
@@ -1,7 +1,7 @@
/*
* U-boot - bf533_serial.h Serial Driver defines
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on
* bf533_serial.h: Definitions for the BlackFin BF533 DSP serial driver.
@@ -38,8 +38,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _Bf533_SERIAL_H
diff --git a/cpu/bf533/config.mk b/cpu/bf533/config.mk
index 10817d9..6a713c3 100644
--- a/cpu/bf533/config.mk
+++ b/cpu/bf533/config.mk
@@ -1,6 +1,6 @@
# U-boot - config.mk
#
-# Copyright (c) 2005 blackfin.uclinux.org
+# Copyright (c) 2005-2007 Analog Devices Inc.
#
# (C) Copyright 2000-2004
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -20,8 +20,8 @@
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
+# Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+# MA 02110-1301 USA
#
PLATFORM_RELFLAGS += -mcpu=bf533 -ffixed-P5
diff --git a/cpu/bf533/cpu.c b/cpu/bf533/cpu.c
index ac8ec51..8118861 100644
--- a/cpu/bf533/cpu.c
+++ b/cpu/bf533/cpu.c
@@ -1,7 +1,7 @@
/*
* U-boot - cpu.c CPU specific functions
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <common.h>
@@ -93,7 +93,7 @@
/* Fill the rest with invalid entry */
if (j <= 15) {
- for (; j <= 16; j++) {
+ for (; j < 16; j++) {
debug("filling %i with 0", j);
*I1++ = 0x0;
}
@@ -169,7 +169,7 @@
/* Fill the rest with invalid entry */
if (j <= 15) {
- for (; j <= 16; j++) {
+ for (; j < 16; j++) {
debug("filling %i with 0", j);
*I1++ = 0x0;
}
diff --git a/cpu/bf533/cpu.h b/cpu/bf533/cpu.h
index 821363e..b6b73b1 100644
--- a/cpu/bf533/cpu.h
+++ b/cpu/bf533/cpu.h
@@ -1,7 +1,7 @@
/*
* U-boot - cpu.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _CPU_H_
diff --git a/cpu/bf533/flush.S b/cpu/bf533/flush.S
index 0512f3b..62e3d65 100644
--- a/cpu/bf533/flush.S
+++ b/cpu/bf533/flush.S
@@ -1,9 +1,9 @@
-/* Copyright (C) 2003 Analog Devices, Inc. All Rights Reserved.
- * Copyright (C) 2004 LG SOft India. All Rights Reserved.
+/* Copyright (C) 2003-2007 Analog Devices Inc.
*
* This file is subject to the terms and conditions of the GNU General Public
* License.
*/
+
#define ASSEMBLY
#include <asm/linkage.h>
diff --git a/cpu/bf533/interrupt.S b/cpu/bf533/interrupt.S
index 524da8f..c356d53 100644
--- a/cpu/bf533/interrupt.S
+++ b/cpu/bf533/interrupt.S
@@ -1,7 +1,7 @@
/*
* U-boot - interrupt.S Processing of interrupts and exception handling
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -35,8 +35,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#define ASSEMBLY
diff --git a/cpu/bf533/interrupts.c b/cpu/bf533/interrupts.c
index 9317f26..14d06cf 100644
--- a/cpu/bf533/interrupts.c
+++ b/cpu/bf533/interrupts.c
@@ -1,7 +1,7 @@
/*
* U-boot - interrupts.c Interrupt related routines
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on interrupts.c
* Copyright 1996 Roman Zippel
@@ -30,8 +30,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <common.h>
diff --git a/cpu/bf533/ints.c b/cpu/bf533/ints.c
index f476f14..5586689 100644
--- a/cpu/bf533/ints.c
+++ b/cpu/bf533/ints.c
@@ -1,7 +1,7 @@
/*
* U-boot - ints.c Interrupt related routines
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on ints.c
*
@@ -32,8 +32,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <common.h>
diff --git a/cpu/bf533/serial.c b/cpu/bf533/serial.c
index 11a46be..6cab5da 100644
--- a/cpu/bf533/serial.c
+++ b/cpu/bf533/serial.c
@@ -1,7 +1,7 @@
/*
* U-boot - serial.c Serial driver for BF533
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on
* bf533_serial.c: Serial driver for BlackFin BF533 DSP internal UART.
@@ -38,8 +38,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <common.h>
diff --git a/cpu/bf533/start.S b/cpu/bf533/start.S
index 94556d6..67a60cf 100644
--- a/cpu/bf533/start.S
+++ b/cpu/bf533/start.S
@@ -1,7 +1,7 @@
/*
* U-boot - start.S Startup file of u-boot for BF533/BF561
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on head.S
* Copyright (c) 2003 Metrowerks/Motorola
@@ -26,8 +26,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
/*
diff --git a/cpu/bf533/start1.S b/cpu/bf533/start1.S
index 72cfafb..6d4731b 100644
--- a/cpu/bf533/start1.S
+++ b/cpu/bf533/start1.S
@@ -1,7 +1,7 @@
/*
* U-boot - start1.S Code running out of RAM after relocation
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#define ASSEMBLY
diff --git a/cpu/bf533/traps.c b/cpu/bf533/traps.c
index 248e34f..19b1fde 100644
--- a/cpu/bf533/traps.c
+++ b/cpu/bf533/traps.c
@@ -1,7 +1,7 @@
/*
* U-boot - traps.c Routines related to interrupts and exceptions
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on
* No original Copyright holder listed,
@@ -29,8 +29,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <common.h>
@@ -39,7 +39,6 @@
#include <asm/irq.h>
#include <asm/system.h>
#include <asm/traps.h>
-#include <asm/page.h>
#include <asm/machdep.h>
#include "cpu.h"
#include <asm/arch/anomaly.h>
diff --git a/cpu/bf537/Makefile b/cpu/bf537/Makefile
index 61c7338..8b0f9c0 100644
--- a/cpu/bf537/Makefile
+++ b/cpu/bf537/Makefile
@@ -1,6 +1,6 @@
# U-boot - Makefile
#
-# Copyright (c) 2005 blackfin.uclinux.org
+# Copyright (c) 2005-2007 Analog Devices Inc.
#
# (C) Copyright 2000-2004
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -20,8 +20,8 @@
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
+# Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+# MA 02110-1301 USA
#
include $(TOPDIR)/config.mk
diff --git a/cpu/bf537/config.mk b/cpu/bf537/config.mk
index 4d57d9c..8a35789 100644
--- a/cpu/bf537/config.mk
+++ b/cpu/bf537/config.mk
@@ -1,6 +1,6 @@
# U-boot - config.mk
#
-# Copyright (c) 2005 blackfin.uclinux.org
+# Copyright (c) 2005-2007 Analog Devices Inc.
#
# (C) Copyright 2000-2004
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -20,8 +20,8 @@
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
+# Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+# MA 02110-1301 USA
#
PLATFORM_RELFLAGS += -mcpu=bf537 -ffixed-P5
diff --git a/cpu/bf537/cpu.c b/cpu/bf537/cpu.c
index cb8dc3c..62f603b 100644
--- a/cpu/bf537/cpu.c
+++ b/cpu/bf537/cpu.c
@@ -1,7 +1,7 @@
/*
* U-boot - cpu.c CPU specific functions
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <common.h>
diff --git a/cpu/bf537/cpu.h b/cpu/bf537/cpu.h
index 821363e..b6b73b1 100644
--- a/cpu/bf537/cpu.h
+++ b/cpu/bf537/cpu.h
@@ -1,7 +1,7 @@
/*
* U-boot - cpu.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _CPU_H_
diff --git a/cpu/bf537/flush.S b/cpu/bf537/flush.S
index c260a8f..fbd26cc 100644
--- a/cpu/bf537/flush.S
+++ b/cpu/bf537/flush.S
@@ -1,9 +1,9 @@
-/* Copyright (C) 2003 Analog Devices, Inc. All Rights Reserved.
- * Copyright (C) 2004 LG SOft India. All Rights Reserved.
+/* Copyright (C) 2003-2007 Analog Devices Inc.
*
* This file is subject to the terms and conditions of the GNU General Public
* License.
*/
+
#define ASSEMBLY
#include <asm/linkage.h>
diff --git a/cpu/bf537/interrupt.S b/cpu/bf537/interrupt.S
index a8be34f..a71df55 100644
--- a/cpu/bf537/interrupt.S
+++ b/cpu/bf537/interrupt.S
@@ -1,7 +1,7 @@
/*
* U-boot - interrupt.S Processing of interrupts and exception handling
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -35,8 +35,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#define ASSEMBLY
diff --git a/cpu/bf537/interrupts.c b/cpu/bf537/interrupts.c
index 2ca76ec..d2213b1 100644
--- a/cpu/bf537/interrupts.c
+++ b/cpu/bf537/interrupts.c
@@ -1,7 +1,7 @@
/*
* U-boot - interrupts.c Interrupt related routines
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on interrupts.c
* Copyright 1996 Roman Zippel
@@ -30,8 +30,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <common.h>
diff --git a/cpu/bf537/ints.c b/cpu/bf537/ints.c
index f476f14..5586689 100644
--- a/cpu/bf537/ints.c
+++ b/cpu/bf537/ints.c
@@ -1,7 +1,7 @@
/*
* U-boot - ints.c Interrupt related routines
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on ints.c
*
@@ -32,8 +32,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <common.h>
diff --git a/cpu/bf537/serial.c b/cpu/bf537/serial.c
index dd4f916..e04d08a 100644
--- a/cpu/bf537/serial.c
+++ b/cpu/bf537/serial.c
@@ -1,7 +1,7 @@
/*
* U-boot - serial.c Serial driver for BF537
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on
* bf537_serial.c: Serial driver for BlackFin BF537 internal UART.
@@ -38,8 +38,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <common.h>
diff --git a/cpu/bf537/serial.h b/cpu/bf537/serial.h
index c9ee3dc..76555c2 100644
--- a/cpu/bf537/serial.h
+++ b/cpu/bf537/serial.h
@@ -1,7 +1,7 @@
/*
* U-boot - bf537_serial.h Serial Driver defines
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on
* bf533_serial.h: Definitions for the BlackFin BF533 DSP serial driver.
@@ -38,8 +38,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _Bf537_SERIAL_H
diff --git a/cpu/bf537/start.S b/cpu/bf537/start.S
index 264e9b6..4e02bcb 100644
--- a/cpu/bf537/start.S
+++ b/cpu/bf537/start.S
@@ -1,7 +1,7 @@
/*
* U-boot - start.S Startup file of u-boot for BF537
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on head.S
* Copyright (c) 2003 Metrowerks/Motorola
@@ -26,8 +26,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
/*
diff --git a/cpu/bf537/start1.S b/cpu/bf537/start1.S
index 72cfafb..6d4731b 100644
--- a/cpu/bf537/start1.S
+++ b/cpu/bf537/start1.S
@@ -1,7 +1,7 @@
/*
* U-boot - start1.S Code running out of RAM after relocation
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#define ASSEMBLY
diff --git a/cpu/bf537/traps.c b/cpu/bf537/traps.c
index 994ece8..4e18e27 100644
--- a/cpu/bf537/traps.c
+++ b/cpu/bf537/traps.c
@@ -1,7 +1,7 @@
/*
* U-boot - traps.c Routines related to interrupts and exceptions
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on
* No original Copyright holder listed,
@@ -29,8 +29,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <common.h>
@@ -39,7 +39,6 @@
#include <asm/irq.h>
#include <asm/system.h>
#include <asm/traps.h>
-#include <asm/page.h>
#include <asm/machdep.h>
#include "cpu.h"
#include <asm/arch/anomaly.h>
diff --git a/cpu/bf561/Makefile b/cpu/bf561/Makefile
index ee7842a..2947169 100644
--- a/cpu/bf561/Makefile
+++ b/cpu/bf561/Makefile
@@ -1,6 +1,6 @@
# U-boot - Makefile
#
-# Copyright (c) 2005 blackfin.uclinux.org
+# Copyright (c) 2005-2007 Analog Devices Inc.
#
# (C) Copyright 2000-2004
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -20,8 +20,8 @@
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
+# Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+# MA 02110-1301 USA
#
include $(TOPDIR)/config.mk
diff --git a/cpu/bf561/config.mk b/cpu/bf561/config.mk
index c49a0ba..f4dc04b 100644
--- a/cpu/bf561/config.mk
+++ b/cpu/bf561/config.mk
@@ -1,6 +1,6 @@
# U-boot - config.mk
#
-# Copyright (c) 2005 blackfin.uclinux.org
+# Copyright (c) 2005-2007 Analog Devices Inc.
#
# (C) Copyright 2000-2004
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -20,8 +20,8 @@
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
+# Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+# MA 02110-1301 USA
#
PLATFORM_RELFLAGS += -mcpu=bf561 -ffixed-P5
diff --git a/cpu/bf561/cpu.c b/cpu/bf561/cpu.c
index a7b53d8..5b907cd 100644
--- a/cpu/bf561/cpu.c
+++ b/cpu/bf561/cpu.c
@@ -1,7 +1,7 @@
/*
* U-boot - cpu.c CPU specific functions
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <common.h>
diff --git a/cpu/bf561/cpu.h b/cpu/bf561/cpu.h
index 821363e..b6b73b1 100644
--- a/cpu/bf561/cpu.h
+++ b/cpu/bf561/cpu.h
@@ -1,7 +1,7 @@
/*
* U-boot - cpu.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _CPU_H_
diff --git a/cpu/bf561/flush.S b/cpu/bf561/flush.S
index 7e12c83..0140a60 100644
--- a/cpu/bf561/flush.S
+++ b/cpu/bf561/flush.S
@@ -1,9 +1,9 @@
-/* Copyright (C) 2003 Analog Devices, Inc. All Rights Reserved.
- * Copyright (C) 2004 LG SOft India. All Rights Reserved.
+/* Copyright (C) 2003-2007 Analog Devices Inc.
*
* This file is subject to the terms and conditions of the GNU General Public
* License.
*/
+
#define ASSEMBLY
#include <asm/linkage.h>
diff --git a/cpu/bf561/interrupt.S b/cpu/bf561/interrupt.S
index f82fd9b..21839ce 100644
--- a/cpu/bf561/interrupt.S
+++ b/cpu/bf561/interrupt.S
@@ -1,7 +1,7 @@
/*
* U-boot - interrupt.S Processing of interrupts and exception handling
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -35,8 +35,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#define ASSEMBLY
diff --git a/cpu/bf561/interrupts.c b/cpu/bf561/interrupts.c
index e314f60..ecbc6ad 100644
--- a/cpu/bf561/interrupts.c
+++ b/cpu/bf561/interrupts.c
@@ -1,7 +1,7 @@
/*
* U-boot - interrupts.c Interrupt related routines
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on interrupts.c
* Copyright 1996 Roman Zippel
@@ -30,8 +30,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <common.h>
diff --git a/cpu/bf561/ints.c b/cpu/bf561/ints.c
index 328e5d8..27a38a3 100644
--- a/cpu/bf561/ints.c
+++ b/cpu/bf561/ints.c
@@ -1,7 +1,7 @@
/*
* U-boot - ints.c Interrupt related routines
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on ints.c
*
@@ -32,8 +32,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <common.h>
diff --git a/cpu/bf561/serial.c b/cpu/bf561/serial.c
index baec1d3..7f5c695 100644
--- a/cpu/bf561/serial.c
+++ b/cpu/bf561/serial.c
@@ -1,7 +1,7 @@
/*
* U-boot - serial.c Serial driver for BF561
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on
* bf533_serial.c: Serial driver for BlackFin BF533 DSP internal UART.
@@ -38,8 +38,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <common.h>
diff --git a/cpu/bf561/serial.h b/cpu/bf561/serial.h
index 98c1242..c1cbf36 100644
--- a/cpu/bf561/serial.h
+++ b/cpu/bf561/serial.h
@@ -1,7 +1,7 @@
/*
* U-boot - bf561_serial.h Serial Driver defines
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on
* bf533_serial.h: Definitions for the BlackFin BF533 DSP serial driver.
@@ -38,8 +38,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _Bf561_SERIAL_H
diff --git a/cpu/bf561/start.S b/cpu/bf561/start.S
index 9333648..bd26cf3 100644
--- a/cpu/bf561/start.S
+++ b/cpu/bf561/start.S
@@ -1,7 +1,7 @@
/*
* U-boot - start.S Startup file of u-boot for BF533/BF561
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on head.S
* Copyright (c) 2003 Metrowerks/Motorola
@@ -26,8 +26,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
/*
diff --git a/cpu/bf561/start1.S b/cpu/bf561/start1.S
index 72cfafb..6d4731b 100644
--- a/cpu/bf561/start1.S
+++ b/cpu/bf561/start1.S
@@ -1,7 +1,7 @@
/*
* U-boot - start1.S Code running out of RAM after relocation
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#define ASSEMBLY
diff --git a/cpu/bf561/traps.c b/cpu/bf561/traps.c
index f5ff3a8..7e2dcd1 100644
--- a/cpu/bf561/traps.c
+++ b/cpu/bf561/traps.c
@@ -1,7 +1,7 @@
/*
* U-boot - traps.c Routines related to interrupts and exceptions
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on
* No original Copyright holder listed,
@@ -29,8 +29,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <common.h>
diff --git a/cpu/microblaze/Makefile b/cpu/microblaze/Makefile
index fd54425..db1afa5 100644
--- a/cpu/microblaze/Makefile
+++ b/cpu/microblaze/Makefile
@@ -26,7 +26,8 @@
LIB = $(obj)lib$(CPU).a
START = start.o
-COBJS = cpu.o interrupts.o
+SOBJS = dcache.o icache.o irq.o disable_int.o enable_int.o
+COBJS = cpu.o interrupts.o cache.o exception.o timer.o
SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
diff --git a/cpu/microblaze/cache.c b/cpu/microblaze/cache.c
new file mode 100644
index 0000000..fc388eb
--- /dev/null
+++ b/cpu/microblaze/cache.c
@@ -0,0 +1,48 @@
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal SIMEK <moonstr@monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+#if (CONFIG_COMMANDS & CFG_CMD_CACHE)
+
+int dcache_status (void)
+{
+ int i = 0;
+ int mask = 0x80;
+ __asm__ __volatile__ ("mfs %0,rmsr"::"r" (i):"memory");
+ /* i&=0x80 */
+ __asm__ __volatile__ ("and %0,%0,%1"::"r" (i), "r" (mask):"memory");
+ return i;
+}
+
+int icache_status (void)
+{
+ int i = 0;
+ int mask = 0x20;
+ __asm__ __volatile__ ("mfs %0,rmsr"::"r" (i):"memory");
+ /* i&=0x20 */
+ __asm__ __volatile__ ("and %0,%0,%1"::"r" (i), "r" (mask):"memory");
+ return i;
+}
+#endif
diff --git a/cpu/microblaze/dcache.S b/cpu/microblaze/dcache.S
new file mode 100644
index 0000000..eaf9671
--- /dev/null
+++ b/cpu/microblaze/dcache.S
@@ -0,0 +1,68 @@
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal SIMEK <monstr@monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+ .text
+ .globl dcache_enable
+ .ent dcache_enable
+ .align 2
+dcache_enable:
+ /* Make space on stack for a temporary */
+ addi r1, r1, -4
+ /* Save register r12 */
+ swi r12, r1, 0
+ /* Read the MSR register */
+ mfs r12, rmsr
+ /* Set the instruction enable bit */
+ ori r12, r12, 0x80
+ /* Save the MSR register */
+ mts rmsr, r12
+ /* Load register r12 */
+ lwi r12, r1, 0
+ /* Return */
+ rtsd r15, 8
+ /* Update stack in the delay slot */
+ addi r1, r1, 4
+ .end dcache_enable
+
+ .text
+ .globl dcache_disable
+ .ent dcache_disable
+ .align 2
+dcache_disable:
+ /* Make space on stack for a temporary */
+ addi r1, r1, -4
+ /* Save register r12 */
+ swi r12, r1, 0
+ /* Read the MSR register */
+ mfs r12, rmsr
+ /* Clear the data cache enable bit */
+ andi r12, r12, ~0x80
+ /* Save the MSR register */
+ mts rmsr, r12
+ /* Load register r12 */
+ lwi r12, r1, 0
+ /* Return */
+ rtsd r15, 8
+ /* Update stack in the delay slot */
+ addi r1, r1, 4
+ .end dcache_disable
diff --git a/cpu/microblaze/disable_int.S b/cpu/microblaze/disable_int.S
new file mode 100644
index 0000000..aecd795
--- /dev/null
+++ b/cpu/microblaze/disable_int.S
@@ -0,0 +1,46 @@
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal SIMEK <monstr@monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+ .text
+ .globl microblaze_disable_interrupts
+ .ent microblaze_disable_interrupts
+ .align 2
+microblaze_disable_interrupts:
+ #Make space on stack for a temporary
+ addi r1, r1, -4
+ #Save register r12
+ swi r12, r1, 0
+ #Read the MSR register
+ mfs r12, rmsr
+ #Clear the interrupt enable bit
+ andi r12, r12, ~2
+ #Save the MSR register
+ mts rmsr, r12
+ #Load register r12
+ lwi r12, r1, 0
+ #Return
+ rtsd r15, 8
+ #Update stack in the delay slot
+ addi r1, r1, 4
+ .end microblaze_disable_interrupts
diff --git a/include/asm-microblaze/platform.h b/cpu/microblaze/enable_int.S
similarity index 63%
rename from include/asm-microblaze/platform.h
rename to cpu/microblaze/enable_int.S
index 2096cce..c096c6c 100644
--- a/include/asm-microblaze/platform.h
+++ b/cpu/microblaze/enable_int.S
@@ -1,7 +1,7 @@
/*
- * (C) Copyright 2004 Atmark Techno, Inc.
+ * (C) Copyright 2007 Michal Simek
*
- * Yasushi SHOJI <yashi@atmark-techno.com>
+ * Michal SIMEK <monstrmonstr.eu>
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -13,7 +13,7 @@
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
@@ -22,8 +22,17 @@
* MA 02111-1307 USA
*/
-#include <config.h>
-
-#ifdef CONFIG_SUZAKU
-#include <asm/suzaku.h>
-#endif
+ .text
+ .globl microblaze_enable_interrupts
+ .ent microblaze_enable_interrupts
+ .align 2
+microblaze_enable_interrupts:
+ addi r1, r1, -4
+ swi r12, r1, 0
+ mfs r12, rmsr
+ ori r12, r12, 2
+ mts rmsr, r12
+ lwi r12, r1, 0
+ rtsd r15, 8
+ addi r1, r1, 4
+ .end microblaze_enable_interrupts
diff --git a/cpu/microblaze/exception.c b/cpu/microblaze/exception.c
new file mode 100644
index 0000000..b135acb
--- /dev/null
+++ b/cpu/microblaze/exception.c
@@ -0,0 +1,68 @@
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal SIMEK <monstr@monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+void _hw_exception_handler (void)
+{
+ int address = 0;
+ int state = 0;
+ /* loading address of exception EAR */
+ __asm__ __volatile ("mfs %0,rear"::"r" (address):"memory");
+ /* loading excetpion state register ESR */
+ __asm__ __volatile ("mfs %0,resr"::"r" (state):"memory");
+ printf ("Hardware exception at 0x%x address\n", address);
+ switch (state & 0x1f) { /* mask on exception cause */
+ case 0x1:
+ puts ("Unaligned data access exception\n");
+ break;
+ case 0x2:
+ puts ("Illegal op-code exception\n");
+ break;
+ case 0x3:
+ puts ("Instruction bus error exception\n");
+ break;
+ case 0x4:
+ puts ("Data bus error exception\n");
+ break;
+ case 0x5:
+ puts ("Divide by zero exception\n");
+ break;
+ default:
+ puts ("Undefined cause\n");
+ break;
+ }
+ printf ("Unaligned %sword access\n", ((state & 0x800) ? "" : "half"));
+ printf ("Unaligned %s access\n", ((state & 0x400) ? "store" : "load"));
+ printf ("Register R%x\n", (state & 0x3E) >> 5);
+ hang ();
+}
+
+#ifdef CFG_USR_EXCEP
+void _exception_handler (void)
+{
+ puts ("User vector_exception\n");
+ hang ();
+}
+#endif
diff --git a/cpu/microblaze/icache.S b/cpu/microblaze/icache.S
new file mode 100644
index 0000000..25940d1
--- /dev/null
+++ b/cpu/microblaze/icache.S
@@ -0,0 +1,69 @@
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal SIMEK <monstr@monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+ .text
+ .globl icache_enable
+ .ent icache_enable
+ .align 2
+icache_enable:
+ /* Make space on stack for a temporary */
+ addi r1, r1, -4
+ /* Save register r12 */
+ swi r12, r1, 0
+ /* Read the MSR register */
+ mfs r12, rmsr
+ /* Set the instruction enable bit */
+ ori r12, r12, 0x20
+ /* Save the MSR register */
+ mts rmsr, r12
+ /* Load register r12 */
+ lwi r12, r1, 0
+ /* Return */
+ rtsd r15, 8
+ /* Update stack in the delay slot */
+ addi r1, r1, 4
+ .end icache_enable
+
+ .text
+ .globl icache_disable
+ .ent icache_disable
+ .align 2
+icache_disable:
+ /* Make space on stack for a temporary */
+ addi r1, r1, -4
+ /* Save register r12 */
+ swi r12, r1, 0
+ /* Read the MSR register */
+ mfs r12, rmsr
+ /* Clear the instruction enable bit */
+ andi r12, r12, ~0x20
+ /* Save the MSR register */
+ mts rmsr, r12
+ /* Load register r12 */
+ lwi r12, r1, 0
+ /* Return */
+ rtsd r15, 8
+ /* Update stack in the delay slot */
+ addi r1, r1, 4
+ .end icache_disable
diff --git a/cpu/microblaze/interrupts.c b/cpu/microblaze/interrupts.c
index ccf67e1..2db847c 100644
--- a/cpu/microblaze/interrupts.c
+++ b/cpu/microblaze/interrupts.c
@@ -1,6 +1,8 @@
/*
+ * (C) Copyright 2007 Michal Simek
* (C) Copyright 2004 Atmark Techno, Inc.
*
+ * Michal SIMEK <monstr@monstr.eu>
* Yasushi SHOJI <yashi@atmark-techno.com>
*
* See file CREDITS for list of people who contributed to this
@@ -13,7 +15,7 @@
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
@@ -22,11 +24,185 @@
* MA 02111-1307 USA
*/
-void enable_interrupts(void)
+#include <common.h>
+#include <command.h>
+#include <asm/microblaze_intc.h>
+
+#undef DEBUG_INT
+
+extern void microblaze_disable_interrupts (void);
+extern void microblaze_enable_interrupts (void);
+
+void enable_interrupts (void)
{
+ microblaze_enable_interrupts ();
}
-int disable_interrupts(void)
+int disable_interrupts (void)
{
+ microblaze_disable_interrupts ();
return 0;
}
+
+#ifdef CFG_INTC_0
+#ifdef CFG_TIMER_0
+extern void timer_init (void);
+#endif
+
+static struct irq_action vecs[CFG_INTC_0_NUM];
+
+/* mapping structure to interrupt controller */
+microblaze_intc_t *intc = (microblaze_intc_t *) (CFG_INTC_0_ADDR);
+
+/* default handler */
+void def_hdlr (void)
+{
+ puts ("def_hdlr\n");
+}
+
+void enable_one_interrupt (int irq)
+{
+ int mask;
+ int offset = 1;
+ offset <<= irq;
+ mask = intc->ier;
+ intc->ier = (mask | offset);
+#ifdef DEBUG_INT
+ printf ("Enable one interrupt irq %x - mask %x,ier %x\n", offset, mask,
+ intc->ier);
+ printf ("INTC isr %x, ier %x, iar %x, mer %x\n", intc->isr, intc->ier,
+ intc->iar, intc->mer);
+#endif
+}
+
+void disable_one_interrupt (int irq)
+{
+ int mask;
+ int offset = 1;
+ offset <<= irq;
+ mask = intc->ier;
+ intc->ier = (mask & ~offset);
+#ifdef DEBUG_INT
+ printf ("Disable one interrupt irq %x - mask %x,ier %x\n", irq, mask,
+ intc->ier);
+ printf ("INTC isr %x, ier %x, iar %x, mer %x\n", intc->isr, intc->ier,
+ intc->iar, intc->mer);
+#endif
+}
+
+/* adding new handler for interrupt */
+void install_interrupt_handler (int irq, interrupt_handler_t * hdlr, void *arg)
+{
+ struct irq_action *act;
+ /* irq out of range */
+ if ((irq < 0) || (irq > CFG_INTC_0_NUM)) {
+ puts ("IRQ out of range\n");
+ return;
+ }
+ act = &vecs[irq];
+ if (hdlr) { /* enable */
+ act->handler = hdlr;
+ act->arg = arg;
+ act->count = 0;
+ enable_one_interrupt (irq);
+ } else { /* disable */
+
+ act->handler = (interrupt_handler_t *) def_hdlr;
+ act->arg = (void *)irq;
+ disable_one_interrupt (irq);
+ }
+}
+
+/* initialization interrupt controller - hardware */
+void intc_init (void)
+{
+ intc->mer = 0;
+ intc->ier = 0;
+ intc->iar = 0xFFFFFFFF;
+ /* XIntc_Start - hw_interrupt enable and all interrupt enable */
+ intc->mer = 0x3;
+#ifdef DEBUG_INT
+ printf ("INTC isr %x, ier %x, iar %x, mer %x\n", intc->isr, intc->ier,
+ intc->iar, intc->mer);
+#endif
+}
+
+int interrupts_init (void)
+{
+ int i;
+ /* initialize irq list */
+ for (i = 0; i < CFG_INTC_0_NUM; i++) {
+ vecs[i].handler = (interrupt_handler_t *) def_hdlr;
+ vecs[i].arg = (void *)i;
+ vecs[i].count = 0;
+ }
+ /* initialize intc controller */
+ intc_init ();
+#ifdef CFG_TIMER_0
+ timer_init ();
+#endif
+ enable_interrupts ();
+ return 0;
+}
+
+void interrupt_handler (void)
+{
+ int irqs;
+ irqs = (intc->isr & intc->ier); /* find active interrupt */
+
+#ifdef DEBUG_INT
+ printf ("INTC isr %x, ier %x, iar %x, mer %x\n", intc->isr, intc->ier,
+ intc->iar, intc->mer);
+ printf ("Interrupt handler on %x line, r14 %x\n", irqs, value);
+#endif
+ struct irq_action *act = vecs;
+ while (irqs) {
+ if (irqs & 1) {
+#ifdef DEBUG_INT
+ printf
+ ("Jumping to interrupt handler rutine addr %x,count %x,arg %x\n",
+ act->handler, act->count, act->arg);
+#endif
+ act->handler (act->arg);
+ act->count++;
+ }
+ irqs >>= 1;
+ act++;
+ }
+ intc->iar = 0xFFFFFFFF; /* erase all events */
+#ifdef DEBUG
+ printf ("Dump INTC reg, isr %x, ier %x, iar %x, mer %x\n", intc->isr,
+ intc->ier, intc->iar, intc->mer);
+ printf ("Interrupt handler on %x line, r14\n", irqs);
+#endif
+}
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_IRQ)
+#ifdef CFG_INTC_0
+int do_irqinfo (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
+{
+ int i;
+ struct irq_action *act = vecs;
+
+ puts ("\nInterrupt-Information:\n\n"
+ "Nr Routine Arg Count\n"
+ "-----------------------------\n");
+
+ for (i = 0; i < CFG_INTC_0_NUM; i++) {
+ if (act->handler != (interrupt_handler_t*) def_hdlr) {
+ printf ("%02d %08lx %08lx %d\n", i,
+ (int)act->handler, (int)act->arg, act->count);
+ }
+ act++;
+ }
+ puts ("\n");
+ return (0);
+}
+#else
+int do_irqinfo (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
+{
+ puts ("Undefined interrupt controller\n");
+}
+#endif
+#endif /* CONFIG_COMMANDS & CFG_CMD_IRQ */
diff --git a/cpu/microblaze/irq.S b/cpu/microblaze/irq.S
new file mode 100644
index 0000000..a4e3fbf
--- /dev/null
+++ b/cpu/microblaze/irq.S
@@ -0,0 +1,165 @@
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal SIMEK <monstr@monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+ .text
+ .global _interrupt_handler
+_interrupt_handler:
+ addi r1, r1, -4
+ swi r2, r1, 0
+ addi r1, r1, -4
+ swi r3, r1, 0
+ addi r1, r1, -4
+ swi r4, r1, 0
+ addi r1, r1, -4
+ swi r5, r1, 0
+ addi r1, r1, -4
+ swi r6, r1, 0
+ addi r1, r1, -4
+ swi r7, r1, 0
+ addi r1, r1, -4
+ swi r8, r1, 0
+ addi r1, r1, -4
+ swi r9, r1, 0
+ addi r1, r1, -4
+ swi r10, r1, 0
+ addi r1, r1, -4
+ swi r11, r1, 0
+ addi r1, r1, -4
+ swi r12, r1, 0
+ addi r1, r1, -4
+ swi r13, r1, 0
+ addi r1, r1, -4
+ swi r14, r1, 0
+ addi r1, r1, -4
+ swi r15, r1, 0
+ addi r1, r1, -4
+ swi r16, r1, 0
+ addi r1, r1, -4
+ swi r17, r1, 0
+ addi r1, r1, -4
+ swi r18, r1, 0
+ addi r1, r1, -4
+ swi r19, r1, 0
+ addi r1, r1, -4
+ swi r20, r1, 0
+ addi r1, r1, -4
+ swi r21, r1, 0
+ addi r1, r1, -4
+ swi r22, r1, 0
+ addi r1, r1, -4
+ swi r23, r1, 0
+ addi r1, r1, -4
+ swi r24, r1, 0
+ addi r1, r1, -4
+ swi r25, r1, 0
+ addi r1, r1, -4
+ swi r26, r1, 0
+ addi r1, r1, -4
+ swi r27, r1, 0
+ addi r1, r1, -4
+ swi r28, r1, 0
+ addi r1, r1, -4
+ swi r29, r1, 0
+ addi r1, r1, -4
+ swi r30, r1, 0
+ addi r1, r1, -4
+ swi r31, r1, 0
+ brlid r15, interrupt_handler
+ nop
+ nop
+ lwi r31, r1, 0
+ addi r1, r1, 4
+ lwi r30, r1, 0
+ addi r1, r1, 4
+ lwi r29, r1, 0
+ addi r1, r1, 4
+ lwi r28, r1, 0
+ addi r1, r1, 4
+ lwi r27, r1, 0
+ addi r1, r1, 4
+ lwi r26, r1, 0
+ addi r1, r1, 4
+ lwi r25, r1, 0
+ addi r1, r1, 4
+ lwi r24, r1, 0
+ addi r1, r1, 4
+ lwi r23, r1, 0
+ addi r1, r1, 4
+ lwi r22, r1, 0
+ addi r1, r1, 4
+ lwi r21, r1, 0
+ addi r1, r1, 4
+ lwi r20, r1, 0
+ addi r1, r1, 4
+ lwi r19, r1, 0
+ addi r1, r1, 4
+ lwi r18, r1, 0
+ addi r1, r1, 4
+ lwi r17, r1, 0
+ addi r1, r1, 4
+ lwi r16, r1, 0
+ addi r1, r1, 4
+ lwi r15, r1, 0
+ addi r1, r1, 4
+ lwi r14, r1, 0
+ addi r1, r1, 4
+ lwi r13, r1, 0
+ addi r1, r1, 4
+ lwi r12, r1, 0
+ addi r1, r1, 4
+ lwi r11, r1, 0
+ addi r1, r1, 4
+ lwi r10, r1, 0
+ addi r1, r1, 4
+ lwi r9, r1, 0
+ addi r1, r1, 4
+ lwi r8, r1, 0
+ addi r1, r1, 4
+ lwi r7, r1, 0
+ addi r1, r1, 4
+ lwi r6, r1, 0
+ addi r1, r1, 4
+ lwi r5, r1, 0
+ addi r1, r1, 4
+ lwi r4, r1, 0
+ addi r1, r1, 4
+ lwi r3, r1, 0
+ addi r1, r1, 4
+ lwi r2, r1, 0
+ addi r1, r1, 4
+
+ /* enable_interrupt */
+ addi r1, r1, -4
+ swi r12, r1, 0
+ mfs r12, rmsr
+ ori r12, r12, 2
+ mts rmsr, r12
+ lwi r12, r1, 0
+ addi r1, r1, 4
+ nop
+ bra r14
+ nop
+ nop
+ .size _interrupt_handler,.-_interrupt_handler
diff --git a/cpu/microblaze/start.S b/cpu/microblaze/start.S
index 7efdbb0..ca3befc 100644
--- a/cpu/microblaze/start.S
+++ b/cpu/microblaze/start.S
@@ -1,6 +1,8 @@
/*
+ * (C) Copyright 2007 Michal Simek
* (C) Copyright 2004 Atmark Techno, Inc.
*
+ * Michal SIMEK <monstr@monstr.eu>
* Yasushi SHOJI <yashi@atmark-techno.com>
*
* See file CREDITS for list of people who contributed to this
@@ -13,7 +15,7 @@
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
@@ -27,10 +29,91 @@
.text
.global _start
_start:
+ mts rmsr, r0 /* disable cache */
+ addi r1, r0, CFG_INIT_SP_OFFSET
+ addi r1, r1, -4 /* Decrement SP to top of memory */
+ /* add opcode instruction for 32bit jump - 2 instruction imm & brai*/
+ addi r6, r0, 0xb000 /* hex b000 opcode imm */
+ bslli r6, r6, 16 /* shift */
+ swi r6, r0, 0x0 /* reset address */
+ swi r6, r0, 0x8 /* user vector exception */
+ swi r6, r0, 0x10 /* interrupt */
+ swi r6, r0, 0x20 /* hardware exception */
- addi r1, r0, CFG_SDRAM_BASE /* init stack pointer */
- addi r1, r1, CFG_SDRAM_SIZE /* set sp to high up */
+ addi r6, r0, 0xb808 /* hew b808 opcode brai*/
+ bslli r6, r6, 16
+ swi r6, r0, 0x4 /* reset address */
+ swi r6, r0, 0xC /* user vector exception */
+ swi r6, r0, 0x14 /* interrupt */
+ swi r6, r0, 0x24 /* hardware exception */
- brai board_init
+#ifdef CFG_RESET_ADDRESS
+ /* reset address */
+ addik r6, r0, CFG_RESET_ADDRESS
+ sw r6, r1, r0
+ lhu r7, r1, r0
+ shi r7, r0, 0x2
+ shi r6, r0, 0x6
+/*
+ * Copy U-Boot code to TEXT_BASE
+ * solve problem with sbrk_base
+ */
+#if (CFG_RESET_ADDRESS != TEXT_BASE)
+ addi r4, r0, __end
+ addi r5, r0, __text_start
+ rsub r4, r5, r4 /* size = __end - __text_start */
+ addi r6, r0, CFG_RESET_ADDRESS /* source address */
+ addi r7, r0, 0 /* counter */
+4:
+ lw r8, r6, r7
+ sw r8, r5, r7
+ addi r7, r7, 0x4
+ cmp r8, r4, r7
+ blti r8, 4b
+#endif
+#endif
+#ifdef CFG_USR_EXCEP
+ /* user_vector_exception */
+ addik r6, r0, _exception_handler
+ sw r6, r1, r0
+ lhu r7, r1, r0
+ shi r7, r0, 0xa
+ shi r6, r0, 0xe
+#endif
+
+#ifdef CFG_INTC_0
+ /* interrupt_handler */
+ addik r6, r0, _interrupt_handler
+ sw r6, r1, r0
+ lhu r7, r1, r0
+ shi r7, r0, 0x12
+ shi r6, r0, 0x16
+#endif
+
+ /* hardware exception */
+ addik r6, r0, _hw_exception_handler
+ sw r6, r1, r0
+ lhu r7, r1, r0
+ shi r7, r0, 0x22
+ shi r6, r0, 0x26
+
+ /* enable instruction and data cache */
+ mfs r12, rmsr
+ ori r12, r12, 0xa0
+ mts rmsr, r12
+
+clear_bss:
+ /* clear BSS segments */
+ addi r5, r0, __bss_start
+ addi r4, r0, __bss_end
+ cmp r6, r5, r4
+ beqi r6, 3f
+2:
+ swi r0, r5, 0 /* write zero to loc */
+ addi r5, r5, 4 /* increment to next loc */
+ cmp r6, r5, r4 /* check if we have reach the end */
+ bnei r6, 2b
+3: /* jumping to board_init */
+ brai board_init
1: bri 1b
diff --git a/cpu/microblaze/timer.c b/cpu/microblaze/timer.c
new file mode 100644
index 0000000..be4fd57
--- /dev/null
+++ b/cpu/microblaze/timer.c
@@ -0,0 +1,68 @@
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal SIMEK <monstr@monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/microblaze_timer.h>
+
+volatile int timestamp = 0;
+
+void reset_timer (void)
+{
+ timestamp = 0;
+}
+
+ulong get_timer (ulong base)
+{
+ return (timestamp - base);
+}
+
+void set_timer (ulong t)
+{
+ timestamp = t;
+}
+
+#ifdef CFG_INTC_0
+#ifdef CFG_TIMER_0
+extern void install_interrupt_handler (int irq, interrupt_handler_t * hdlr,
+ void *arg);
+
+microblaze_timer_t *tmr = (microblaze_timer_t *) (CFG_TIMER_0_ADDR);
+
+void timer_isr (void *arg)
+{
+ timestamp++;
+ tmr->control = tmr->control | TIMER_INTERRUPT;
+}
+
+void timer_init (void)
+{
+ tmr->loadreg = CFG_TIMER_0_PRELOAD;
+ tmr->control = TIMER_INTERRUPT | TIMER_RESET;
+ tmr->control =
+ TIMER_ENABLE | TIMER_ENABLE_INTR | TIMER_RELOAD | TIMER_DOWN_COUNT;
+ reset_timer ();
+ install_interrupt_handler (CFG_TIMER_0_IRQ, timer_isr, (void *)tmr);
+}
+#endif
+#endif
diff --git a/cpu/mpc5xxx/fec.c b/cpu/mpc5xxx/fec.c
index 13a3870..e59bd85 100644
--- a/cpu/mpc5xxx/fec.c
+++ b/cpu/mpc5xxx/fec.c
@@ -467,6 +467,10 @@
miiphy_write(dev->name, phyAddr, 0x0, 0x8000);
udelay(1000);
+#if defined(CONFIG_UC101)
+ /* Set the LED configuration Register for the UC101 Board */
+ miiphy_write(dev->name, phyAddr, 0x14, 0x4122);
+#endif
if (fec->xcv_type == MII10) {
/*
* Force 10Base-T, FDX operation
diff --git a/cpu/mpc83xx/cpu.c b/cpu/mpc83xx/cpu.c
index e4bc405..21b1646 100644
--- a/cpu/mpc83xx/cpu.c
+++ b/cpu/mpc83xx/cpu.c
@@ -30,8 +30,14 @@
#include <watchdog.h>
#include <command.h>
#include <mpc83xx.h>
-#include <ft_build.h>
#include <asm/processor.h>
+#if defined(CONFIG_OF_FLAT_TREE)
+#include <ft_build.h>
+#endif
+#if defined(CONFIG_OF_LIBFDT)
+#include <libfdt.h>
+#include <libfdt_env.h>
+#endif
DECLARE_GLOBAL_DATA_PTR;
@@ -291,6 +297,100 @@
}
#endif
+#if defined(CONFIG_OF_LIBFDT)
+
+/*
+ * Fixups to the fdt. If "create" is TRUE, the node is created
+ * unconditionally. If "create" is FALSE, the node is updated
+ * only if it already exists.
+ */
+#define FT_UPDATE 0x00000000 /* update existing property only */
+#define FT_CREATE 0x00000001 /* create property if it doesn't exist */
+#define FT_BUSFREQ 0x00000002 /* source is bd->bi_busfreq */
+#define FT_ENETADDR 0x00000004 /* source is bd->bi_enetaddr */
+static const struct {
+ int createflags;
+ char *node;
+ char *prop;
+} fixup_props[] = {
+ { FT_CREATE | FT_BUSFREQ,
+ "/cpus/" OF_CPU,
+ "bus-frequency",
+ },
+ { FT_CREATE | FT_BUSFREQ,
+ "/cpus/" OF_SOC,
+ "bus-frequency"
+ },
+ { FT_CREATE | FT_BUSFREQ,
+ "/" OF_SOC "/serial@4500/",
+ "clock-frequency"
+ },
+ { FT_CREATE | FT_BUSFREQ,
+ "/" OF_SOC "/serial@4600/",
+ "clock-frequency"
+ },
+#ifdef CONFIG_MPC83XX_TSEC1
+ { FT_UPDATE | FT_ENETADDR,
+ "/" OF_SOC "/ethernet@24000,
+ "mac-address",
+ },
+ { FT_UPDATE | FT_ENETADDR,
+ "/" OF_SOC "/ethernet@24000,
+ "local-mac-address",
+ },
+#endif
+#ifdef CONFIG_MPC83XX_TSEC2
+ { FT_UPDATE | FT_ENETADDR,
+ "/" OF_SOC "/ethernet@25000,
+ "mac-address",
+ },
+ { FT_UPDATE | FT_ENETADDR,
+ "/" OF_SOC "/ethernet@25000,
+ "local-mac-address",
+ },
+#endif
+};
+
+void
+ft_cpu_setup(void *blob, bd_t *bd)
+{
+ int nodeoffset;
+ int err;
+ int j;
+
+ for (j = 0; j < (sizeof(fixup_props) / sizeof(fixup_props[0])); j++) {
+ nodeoffset = fdt_path_offset (fdt, fixup_props[j].node);
+ if (nodeoffset >= 0) {
+ /*
+ * If unconditional create or the property already exists...
+ */
+ if ((fixup_props[j].createflags & FT_CREATE) ||
+ (fdt_get_property(fdt, nodeoffset, fixup_props[j].prop, 0))) {
+ if (fixup_props[j].createflags & FT_BUSFREQ) {
+ u32 tmp;
+
+ tmp = cpu_to_be32(bd->bi_busfreq);
+ err = fdt_setprop(fdt, nodeoffset,
+ fixup_props[j].prop, &tmp, sizeof(tmp));
+ } else if (fixup_props[j].createflags & FT_ENETADDR) {
+ err = fdt_setprop(fdt, nodeoffset,
+ fixup_props[j].prop, bd->bi_enetaddr, 6);
+ } else {
+ printf("ft_cpu_setup: %s %s has no flag for the value to set\n",
+ fixup_props[j].node,
+ fixup_props[j].prop);
+ }
+ if (err < 0)
+ printf("libfdt: %s %s returned %s\n",
+ fixup_props[j].node,
+ fixup_props[j].prop,
+ fdt_strerror(err));
+ }
+ }
+ }
+}
+#endif
+
#if defined(CONFIG_OF_FLAT_TREE)
void
ft_cpu_setup(void *blob, bd_t *bd)
diff --git a/cpu/ppc4xx/44x_spd_ddr2.c b/cpu/ppc4xx/44x_spd_ddr2.c
index 83c9911..2ecd3e4 100644
--- a/cpu/ppc4xx/44x_spd_ddr2.c
+++ b/cpu/ppc4xx/44x_spd_ddr2.c
@@ -107,10 +107,11 @@
#define CALC_ODT_RW(n) (CALC_ODT_R(n) | CALC_ODT_W(n))
/* Defines for the Read Cycle Delay test */
-#define NUMMEMTESTS 8
-#define NUMMEMWORDS 8
+#define NUMMEMTESTS 8
+#define NUMMEMWORDS 8
+#define NUMLOOPS 256 /* memory test loops */
-#define CONFIG_ECC_ERROR_RESET /* test-only: see description below, at check_ecc() */
+#undef CONFIG_ECC_ERROR_RESET /* test-only: see description below, at check_ecc() */
/*
* This DDR2 setup code can dynamically setup the TLB entries for the DDR2 memory
@@ -584,10 +585,23 @@
#ifdef CONFIG_ADD_RAM_INFO
void board_add_ram_info(int use_default)
{
+ PPC440_SYS_INFO board_cfg;
+ u32 val;
+
if (is_ecc_enabled())
- puts(" (ECC enabled)");
+ puts(" (ECC");
else
- puts(" (ECC not enabled)");
+ puts(" (ECC not");
+
+ get_sys_info(&board_cfg);
+
+ mfsdr(SDR0_DDR0, val);
+ val = MULDIV64((board_cfg.freqPLB), SDR0_DDR0_DDRM_DECODE(val), 1);
+ printf(" enabled, %d MHz", (val * 2) / 1000000);
+
+ mfsdram(SDRAM_MMODE, val);
+ val = (val & SDRAM_MMODE_DCL_MASK) >> 4;
+ printf(", CL%d)", val);
}
#endif
@@ -731,6 +745,7 @@
else
cycle_time = (((tcyc_reg & 0xF0) >> 4) * 100) +
((tcyc_reg & 0x0F)*10);
+ debug("cycle_time=%d [10 picoseconds]\n", cycle_time);
if (cycle_time > (calc_cycle_time + 10)) {
/*
@@ -1109,7 +1124,7 @@
modt3 = 0x00000000;
}
}
- } else {
+ } else {
codt |= SDRAM_CODT_DQS_2_5_V_DDR1;
modt0 = 0x00000000;
modt1 = 0x00000000;
@@ -1315,6 +1330,7 @@
mfsdr(SDR0_DDR0, sdr_ddrpll);
sdram_freq = MULDIV64((board_cfg.freqPLB), SDR0_DDR0_DDRM_DECODE(sdr_ddrpll), 1);
+ debug("sdram_freq=%d\n", sdram_freq);
/*------------------------------------------------------------------
* Handle the timing. We need to find the worst case timing of all
@@ -1344,6 +1360,7 @@
/* t_wr_ns = max(t_wr_ns, (unsigned long)dimm_spd[dimm_num][36] >> 2); */ /* not used in this loop. */
cas_bit = spd_read(iic0_dimm_addr[dimm_num], 18);
+ debug("cas_bit[SPD byte 18]=%02x\n", cas_bit);
/* For a particular DIMM, grab the three CAS values it supports */
for (cas_index = 0; cas_index < 3; cas_index++) {
@@ -1362,7 +1379,8 @@
if ((tcyc_reg & 0x0F) >= 10) {
if ((tcyc_reg & 0x0F) == 0x0D) {
/* Convert from hex to decimal */
- cycle_time_ns_x_100[cas_index] = (((tcyc_reg & 0xF0) >> 4) * 100) + 75;
+ cycle_time_ns_x_100[cas_index] =
+ (((tcyc_reg & 0xF0) >> 4) * 100) + 75;
} else {
printf("ERROR: SPD reported Tcyc is incorrect for DIMM "
"in slot %d\n", (unsigned int)dimm_num);
@@ -1370,9 +1388,12 @@
}
} else {
/* Convert from hex to decimal */
- cycle_time_ns_x_100[cas_index] = (((tcyc_reg & 0xF0) >> 4) * 100) +
+ cycle_time_ns_x_100[cas_index] =
+ (((tcyc_reg & 0xF0) >> 4) * 100) +
((tcyc_reg & 0x0F)*10);
}
+ debug("cas_index=%d: cycle_time_ns_x_100=%d\n", cas_index,
+ cycle_time_ns_x_100[cas_index]);
}
/* The rest of this routine determines if CAS 2.0, 2.5, 3.0, 4.0 and 5.0 are */
@@ -1385,8 +1406,10 @@
* Bit 7 6 5 4 3 2 1 0
* TBD 4.0 3.5 3.0 2.5 2.0 1.5 1.0
*/
- if (((cas_bit & 0x40) == 0x40) && (cas_index < 3) && (cycle_time_ns_x_100[cas_index] != 0)) {
- max_4_0_tcyc_ns_x_100 = max(max_4_0_tcyc_ns_x_100, cycle_time_ns_x_100[cas_index]);
+ if (((cas_bit & 0x40) == 0x40) && (cas_index < 3) &&
+ (cycle_time_ns_x_100[cas_index] != 0)) {
+ max_4_0_tcyc_ns_x_100 = max(max_4_0_tcyc_ns_x_100,
+ cycle_time_ns_x_100[cas_index]);
cas_index++;
} else {
if (cas_index != 0)
@@ -1394,8 +1417,10 @@
cas_4_0_available = FALSE;
}
- if (((cas_bit & 0x10) == 0x10) && (cas_index < 3) && (cycle_time_ns_x_100[cas_index] != 0)) {
- max_3_0_tcyc_ns_x_100 = max(max_3_0_tcyc_ns_x_100, cycle_time_ns_x_100[cas_index]);
+ if (((cas_bit & 0x10) == 0x10) && (cas_index < 3) &&
+ (cycle_time_ns_x_100[cas_index] != 0)) {
+ max_3_0_tcyc_ns_x_100 = max(max_3_0_tcyc_ns_x_100,
+ cycle_time_ns_x_100[cas_index]);
cas_index++;
} else {
if (cas_index != 0)
@@ -1403,8 +1428,10 @@
cas_3_0_available = FALSE;
}
- if (((cas_bit & 0x08) == 0x08) && (cas_index < 3) && (cycle_time_ns_x_100[cas_index] != 0)) {
- max_2_5_tcyc_ns_x_100 = max(max_2_5_tcyc_ns_x_100, cycle_time_ns_x_100[cas_index]);
+ if (((cas_bit & 0x08) == 0x08) && (cas_index < 3) &&
+ (cycle_time_ns_x_100[cas_index] != 0)) {
+ max_2_5_tcyc_ns_x_100 = max(max_2_5_tcyc_ns_x_100,
+ cycle_time_ns_x_100[cas_index]);
cas_index++;
} else {
if (cas_index != 0)
@@ -1412,8 +1439,10 @@
cas_2_5_available = FALSE;
}
- if (((cas_bit & 0x04) == 0x04) && (cas_index < 3) && (cycle_time_ns_x_100[cas_index] != 0)) {
- max_2_0_tcyc_ns_x_100 = max(max_2_0_tcyc_ns_x_100, cycle_time_ns_x_100[cas_index]);
+ if (((cas_bit & 0x04) == 0x04) && (cas_index < 3) &&
+ (cycle_time_ns_x_100[cas_index] != 0)) {
+ max_2_0_tcyc_ns_x_100 = max(max_2_0_tcyc_ns_x_100,
+ cycle_time_ns_x_100[cas_index]);
cas_index++;
} else {
if (cas_index != 0)
@@ -1426,8 +1455,10 @@
* Bit 7 6 5 4 3 2 1 0
* TBD 6.0 5.0 4.0 3.0 2.0 TBD TBD
*/
- if (((cas_bit & 0x20) == 0x20) && (cas_index < 3) && (cycle_time_ns_x_100[cas_index] != 0)) {
- max_5_0_tcyc_ns_x_100 = max(max_5_0_tcyc_ns_x_100, cycle_time_ns_x_100[cas_index]);
+ if (((cas_bit & 0x20) == 0x20) && (cas_index < 3) &&
+ (cycle_time_ns_x_100[cas_index] != 0)) {
+ max_5_0_tcyc_ns_x_100 = max(max_5_0_tcyc_ns_x_100,
+ cycle_time_ns_x_100[cas_index]);
cas_index++;
} else {
if (cas_index != 0)
@@ -1435,8 +1466,10 @@
cas_5_0_available = FALSE;
}
- if (((cas_bit & 0x10) == 0x10) && (cas_index < 3) && (cycle_time_ns_x_100[cas_index] != 0)) {
- max_4_0_tcyc_ns_x_100 = max(max_4_0_tcyc_ns_x_100, cycle_time_ns_x_100[cas_index]);
+ if (((cas_bit & 0x10) == 0x10) && (cas_index < 3) &&
+ (cycle_time_ns_x_100[cas_index] != 0)) {
+ max_4_0_tcyc_ns_x_100 = max(max_4_0_tcyc_ns_x_100,
+ cycle_time_ns_x_100[cas_index]);
cas_index++;
} else {
if (cas_index != 0)
@@ -1444,8 +1477,10 @@
cas_4_0_available = FALSE;
}
- if (((cas_bit & 0x08) == 0x08) && (cas_index < 3) && (cycle_time_ns_x_100[cas_index] != 0)) {
- max_3_0_tcyc_ns_x_100 = max(max_3_0_tcyc_ns_x_100, cycle_time_ns_x_100[cas_index]);
+ if (((cas_bit & 0x08) == 0x08) && (cas_index < 3) &&
+ (cycle_time_ns_x_100[cas_index] != 0)) {
+ max_3_0_tcyc_ns_x_100 = max(max_3_0_tcyc_ns_x_100,
+ cycle_time_ns_x_100[cas_index]);
cas_index++;
} else {
if (cas_index != 0)
@@ -1468,6 +1503,9 @@
cycle_3_0_clk = MULDIV64(ONE_BILLION, 100, max_3_0_tcyc_ns_x_100) + 10;
cycle_4_0_clk = MULDIV64(ONE_BILLION, 100, max_4_0_tcyc_ns_x_100) + 10;
cycle_5_0_clk = MULDIV64(ONE_BILLION, 100, max_5_0_tcyc_ns_x_100) + 10;
+ debug("cycle_3_0_clk=%d\n", cycle_3_0_clk);
+ debug("cycle_4_0_clk=%d\n", cycle_4_0_clk);
+ debug("cycle_5_0_clk=%d\n", cycle_5_0_clk);
if (sdram_ddr1 == TRUE) { /* DDR1 */
if ((cas_2_0_available == TRUE) && (sdram_freq <= cycle_2_0_clk)) {
@@ -1486,6 +1524,9 @@
hang();
}
} else { /* DDR2 */
+ debug("cas_3_0_available=%d\n", cas_3_0_available);
+ debug("cas_4_0_available=%d\n", cas_4_0_available);
+ debug("cas_5_0_available=%d\n", cas_5_0_available);
if ((cas_3_0_available == TRUE) && (sdram_freq <= cycle_3_0_clk)) {
mmode |= SDRAM_MMODE_DCL_DDR2_3_0_CLK;
*selected_cas = DDR_CAS_3;
@@ -2137,6 +2178,18 @@
return ecc;
}
+static void blank_string(int size)
+{
+ int i;
+
+ for (i=0; i<size; i++)
+ putc('\b');
+ for (i=0; i<size; i++)
+ putc(' ');
+ for (i=0; i<size; i++)
+ putc('\b');
+}
+
#ifdef CONFIG_DDR_ECC
/*-----------------------------------------------------------------------------+
* program_ecc.
@@ -2233,8 +2286,10 @@
unsigned long end_address;
unsigned long address_increment;
unsigned long mcopt1;
- char str[] = "ECC generation...";
- int i;
+ char str[] = "ECC generation -";
+ char slash[] = "\\|/-\\|/-";
+ int loop = 0;
+ int loopi = 0;
current_address = start_address;
mfsdram(SDRAM_MCOPT1, mcopt1);
@@ -2257,14 +2312,20 @@
while (current_address < end_address) {
*((unsigned long *)current_address) = 0x00000000;
current_address += address_increment;
+
+ if ((loop++ % (2 << 20)) == 0) {
+ putc('\b');
+ putc(slash[loopi++ % 8]);
+ }
}
+
} else {
/* ECC bit set method for cached memory */
dcbz_area(start_address, num_bytes);
dflush();
}
- for (i=0; i<strlen(str); i++)
- putc('\b');
+
+ blank_string(strlen(str));
sync();
eieio();
@@ -2347,7 +2408,7 @@
#endif
}
-static u32 short_mem_test(void)
+static int short_mem_test(void)
{
u32 *membase;
u32 bxcr_num;
@@ -2371,42 +2432,41 @@
0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA},
{0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55,
0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55} };
+ int l;
for (bxcr_num = 0; bxcr_num < MAXBXCF; bxcr_num++) {
mfsdram(SDRAM_MB0CF + (bxcr_num << 2), bxcf);
/* Banks enabled */
if ((bxcf & SDRAM_BXCF_M_BE_MASK) == SDRAM_BXCF_M_BE_ENABLE) {
-
/* Bank is enabled */
- membase = (u32 *)(SDRAM_RXBAS_SDBA_DECODE(mfdcr_any(SDRAM_R0BAS+bxcr_num)));
/*------------------------------------------------------------------
* Run the short memory test.
*-----------------------------------------------------------------*/
+ membase = (u32 *)(SDRAM_RXBAS_SDBA_DECODE(mfdcr_any(SDRAM_R0BAS+bxcr_num)));
+
for (i = 0; i < NUMMEMTESTS; i++) {
for (j = 0; j < NUMMEMWORDS; j++) {
membase[j] = test[i][j];
ppcDcbf((u32)&(membase[j]));
}
sync();
- for (j = 0; j < NUMMEMWORDS; j++) {
- if (membase[j] != test[i][j]) {
+ for (l=0; l<NUMLOOPS; l++) {
+ for (j = 0; j < NUMMEMWORDS; j++) {
+ if (membase[j] != test[i][j]) {
+ ppcDcbf((u32)&(membase[j]));
+ return 0;
+ }
ppcDcbf((u32)&(membase[j]));
- break;
}
- ppcDcbf((u32)&(membase[j]));
+ sync();
}
- sync();
- if (j < NUMMEMWORDS)
- break;
}
- if (i < NUMMEMTESTS)
- break;
} /* if bank enabled */
} /* for bxcf_num */
- return bxcr_num;
+ return 1;
}
#ifndef HARD_CODED_DQS
@@ -2415,12 +2475,10 @@
*-----------------------------------------------------------------------------*/
static void DQS_calibration_process(void)
{
- unsigned long ecc_temp;
unsigned long rfdc_reg;
unsigned long rffd;
unsigned long rqdc_reg;
unsigned long rqfd;
- unsigned long bxcr_num;
unsigned long val;
long rqfd_average;
long rffd_average;
@@ -2440,6 +2498,10 @@
long max_end;
unsigned char fail_found;
unsigned char pass_found;
+ u32 rqfd_start;
+ char str[] = "Auto calibration -";
+ char slash[] = "\\|/-\\|/-";
+ int loopi = 0;
/*------------------------------------------------------------------
* Test to determine the best read clock delay tuning bits.
@@ -2464,11 +2526,16 @@
* we can clock the DDR interface at is 200 MHz (2x 100 MHz PLB speed),
* from experimentation it is safe to say you will always have a failure.
*-----------------------------------------------------------------*/
- mfsdram(SDRAM_MCOPT1, ecc_temp);
- ecc_temp &= SDRAM_MCOPT1_MCHK_MASK;
- mfsdram(SDRAM_MCOPT1, val);
- mtsdram(SDRAM_MCOPT1, (val & ~SDRAM_MCOPT1_MCHK_MASK) |
- SDRAM_MCOPT1_MCHK_NON);
+
+ /* first fix RQDC[RQFD] to an average of 80 degre phase shift to find RFDC[RFFD] */
+ rqfd_start = 64; /* test-only: don't know if this is the _best_ start value */
+
+ puts(str);
+
+calibration_loop:
+ mfsdram(SDRAM_RQDC, rqdc_reg);
+ mtsdram(SDRAM_RQDC, (rqdc_reg & ~SDRAM_RQDC_RQFD_MASK) |
+ SDRAM_RQDC_RQFD_ENCODE(rqfd_start));
max_start = 0;
min_end = 0;
@@ -2492,9 +2559,6 @@
fail_found = FALSE;
pass_found = FALSE;
- /* first fix RQDC[RQFD] to an average of 80 degre phase shift to find RFDC[RFFD] */
- /* rqdc_reg = mfsdram(SDRAM_RQDC) & ~(SDRAM_RQDC_RQFD_MASK); */
-
/*
* get the delay line calibration register value
*/
@@ -2510,13 +2574,10 @@
*-----------------------------------------------------------------*/
mtsdram(SDRAM_RFDC, rfdc_reg | SDRAM_RFDC_RFFD_ENCODE(rffd));
- /* do the small memory test */
- bxcr_num = short_mem_test();
-
/*------------------------------------------------------------------
* See if the rffd value passed.
*-----------------------------------------------------------------*/
- if (bxcr_num == MAXBXCF) {
+ if (short_mem_test()) {
if (fail_found == TRUE) {
pass_found = TRUE;
if (current_pass_length == 0)
@@ -2578,13 +2639,10 @@
*-----------------------------------------------------------------*/
mtsdram(SDRAM_RQDC, rqdc_reg | SDRAM_RQDC_RQFD_ENCODE(rqfd));
- /* do the small memory test */
- bxcr_num = short_mem_test();
-
/*------------------------------------------------------------------
* See if the rffd value passed.
*-----------------------------------------------------------------*/
- if (bxcr_num == MAXBXCF) {
+ if (short_mem_test()) {
if (fail_found == TRUE) {
pass_found = TRUE;
if (current_pass_length == 0)
@@ -2612,17 +2670,28 @@
}
}
+ rqfd_average = ((max_start + max_end) >> 1);
+
/*------------------------------------------------------------------
* Make sure we found the valid read passing window. Halt if not
*-----------------------------------------------------------------*/
if (window_found == FALSE) {
- printf("ERROR: Cannot determine a common read delay for the "
+ if (rqfd_start < SDRAM_RQDC_RQFD_MAX) {
+ putc('\b');
+ putc(slash[loopi++ % 8]);
+
+ /* try again from with a different RQFD start value */
+ rqfd_start++;
+ goto calibration_loop;
+ }
+
+ printf("\nERROR: Cannot determine a common read delay for the "
"DIMM(s) installed.\n");
debug("%s[%d] ERROR : \n", __FUNCTION__,__LINE__);
hang();
}
- rqfd_average = ((max_start + max_end) >> 1);
+ blank_string(strlen(str));
if (rqfd_average < 0)
rqfd_average = 0;
@@ -2630,12 +2699,6 @@
if (rqfd_average > SDRAM_RQDC_RQFD_MAX)
rqfd_average = SDRAM_RQDC_RQFD_MAX;
- /*------------------------------------------------------------------
- * Restore the ECC variable to what it originally was
- *-----------------------------------------------------------------*/
- mfsdram(SDRAM_MCOPT1, val);
- mtsdram(SDRAM_MCOPT1, (val & ~SDRAM_MCOPT1_MCHK_MASK) | ecc_temp);
-
mtsdram(SDRAM_RQDC,
(rqdc_reg & ~SDRAM_RQDC_RQFD_MASK) |
SDRAM_RQDC_RQFD_ENCODE(rqfd_average));
diff --git a/cpu/ppc4xx/Makefile b/cpu/ppc4xx/Makefile
index 96f0f62..4068b53 100644
--- a/cpu/ppc4xx/Makefile
+++ b/cpu/ppc4xx/Makefile
@@ -29,7 +29,7 @@
SOBJS = dcr.o
COBJS = 405gp_pci.o 4xx_enet.o \
bedbug_405.o commproc.o \
- cpu.o cpu_init.o i2c.o interrupts.o \
+ cpu.o cpu_init.o gpio.o i2c.o interrupts.o \
miiphy.o ndfc.o sdram.o serial.o \
40x_spd_sdram.o 44x_spd_ddr.o 44x_spd_ddr2.o speed.o \
tlb.o traps.o usb_ohci.o usbdev.o \
diff --git a/cpu/ppc4xx/cpu.c b/cpu/ppc4xx/cpu.c
index 2d8740c..8e6bc84 100644
--- a/cpu/ppc4xx/cpu.c
+++ b/cpu/ppc4xx/cpu.c
@@ -125,6 +125,7 @@
return (val & SDR0_SDCS_SDD);
#endif
}
+#endif
#if defined(CONFIG_440GX)
#define SDR0_PINSTP_SHIFT 29
@@ -178,16 +179,37 @@
};
#endif
+#if defined(CONFIG_405EZ)
+#define SDR0_PINSTP_SHIFT 28
+static char *bootstrap_str[] = {
+ "EBC (8 bits)",
+ "SPI (fast)",
+ "NAND (512 page, 4 addr cycle)",
+ "I2C (Addr 0x50)",
+ "EBC (32 bits)",
+ "I2C (Addr 0x50)",
+ "NAND (2K page, 5 addr cycle)",
+ "I2C (Addr 0x50)",
+ "EBC (16 bits)",
+ "Reserved",
+ "NAND (2K page, 4 addr cycle)",
+ "I2C (Addr 0x50)",
+ "NAND (512 page, 3 addr cycle)",
+ "I2C (Addr 0x50)",
+ "SPI (slow)",
+ "I2C (Addr 0x50)",
+};
+#endif
+
#if defined(SDR0_PINSTP_SHIFT)
static int bootstrap_option(void)
{
unsigned long val;
- mfsdr(sdr_pinstp, val);
- return ((val & 0xe0000000) >> SDR0_PINSTP_SHIFT);
+ mfsdr(SDR_PINSTP, val);
+ return ((val & 0xf0000000) >> SDR0_PINSTP_SHIFT);
}
#endif /* SDR0_PINSTP_SHIFT */
-#endif
#if defined(CONFIG_440)
@@ -403,11 +425,11 @@
#if defined(I2C_BOOTROM)
printf (" I2C boot EEPROM %sabled\n", i2c_bootrom_enabled() ? "en" : "dis");
+#endif /* I2C_BOOTROM */
#if defined(SDR0_PINSTP_SHIFT)
printf (" Bootstrap Option %c - ", (char)bootstrap_option() + 'A');
printf ("Boot ROM Location %s\n", bootstrap_str[bootstrap_option()]);
#endif /* SDR0_PINSTP_SHIFT */
-#endif /* I2C_BOOTROM */
#if defined(CONFIG_PCI)
printf (" Internal PCI arbiter %sabled", pci_arbiter_enabled() ? "en" : "dis");
diff --git a/cpu/ppc4xx/cpu_init.c b/cpu/ppc4xx/cpu_init.c
index 9d1cd13..66e8637 100644
--- a/cpu/ppc4xx/cpu_init.c
+++ b/cpu/ppc4xx/cpu_init.c
@@ -25,6 +25,7 @@
#include <watchdog.h>
#include <ppc4xx_enet.h>
#include <asm/processor.h>
+#include <asm/gpio.h>
#include <ppc4xx.h>
#if defined(CONFIG_405GP) || defined(CONFIG_405EP)
@@ -98,118 +99,6 @@
# endif
#endif /* CFG_INIT_DCACHE_CS */
-#if defined(CFG_440_GPIO_TABLE)
-gpio_param_s gpio_tab[GPIO_GROUP_MAX][GPIO_MAX] = CFG_440_GPIO_TABLE;
-
-void set_chip_gpio_configuration(gpio_param_s (*gpio_tab)[GPIO_GROUP_MAX][GPIO_MAX])
-{
- unsigned char i=0, j=0, reg_offset = 0, gpio_core;
- unsigned long gpio_reg, gpio_core_add;
-
- for (gpio_core=0; gpio_core<GPIO_GROUP_MAX; gpio_core++) {
- j = 0;
- reg_offset = 0;
- /* GPIO config of the GPIOs 0 to 31 */
- for (i=0; i<GPIO_MAX; i++, j++) {
- if (i == GPIO_MAX/2) {
- reg_offset = 4;
- j = i-16;
- }
-
- gpio_core_add = (*gpio_tab)[gpio_core][i].add;
-
- if (((*gpio_tab)[gpio_core][i].in_out == GPIO_IN) ||
- ((*gpio_tab)[gpio_core][i].in_out == GPIO_BI)) {
-
- switch ((*gpio_tab)[gpio_core][i].alt_nb) {
- case GPIO_SEL:
- break;
-
- case GPIO_ALT1:
- gpio_reg = in32(GPIO_IS1(gpio_core_add+reg_offset))
- & ~(GPIO_MASK >> (j*2));
- gpio_reg = gpio_reg | (GPIO_IN_SEL >> (j*2));
- out32(GPIO_IS1(gpio_core_add+reg_offset), gpio_reg);
- break;
-
- case GPIO_ALT2:
- gpio_reg = in32(GPIO_IS2(gpio_core_add+reg_offset))
- & ~(GPIO_MASK >> (j*2));
- gpio_reg = gpio_reg | (GPIO_IN_SEL >> (j*2));
- out32(GPIO_IS2(gpio_core_add+reg_offset), gpio_reg);
- break;
-
- case GPIO_ALT3:
- gpio_reg = in32(GPIO_IS3(gpio_core_add+reg_offset))
- & ~(GPIO_MASK >> (j*2));
- gpio_reg = gpio_reg | (GPIO_IN_SEL >> (j*2));
- out32(GPIO_IS3(gpio_core_add+reg_offset), gpio_reg);
- break;
- }
- }
-
- if (((*gpio_tab)[gpio_core][i].in_out == GPIO_OUT) ||
- ((*gpio_tab)[gpio_core][i].in_out == GPIO_BI)) {
-
- switch ((*gpio_tab)[gpio_core][i].alt_nb) {
- case GPIO_SEL:
- if (gpio_core == GPIO0) {
- gpio_reg = in32(GPIO0_TCR) | (0x80000000 >> (j));
- out32(GPIO0_TCR, gpio_reg);
- }
-
- if (gpio_core == GPIO1) {
- gpio_reg = in32(GPIO1_TCR) | (0x80000000 >> (j));
- out32(GPIO1_TCR, gpio_reg);
- }
-
- gpio_reg = in32(GPIO_OS(gpio_core_add+reg_offset))
- & ~(GPIO_MASK >> (j*2));
- out32(GPIO_OS(gpio_core_add+reg_offset), gpio_reg);
- gpio_reg = in32(GPIO_TS(gpio_core_add+reg_offset))
- & ~(GPIO_MASK >> (j*2));
- out32(GPIO_TS(gpio_core_add+reg_offset), gpio_reg);
- break;
-
- case GPIO_ALT1:
- gpio_reg = in32(GPIO_OS(gpio_core_add+reg_offset))
- & ~(GPIO_MASK >> (j*2));
- gpio_reg = gpio_reg | (GPIO_ALT1_SEL >> (j*2));
- out32(GPIO_OS(gpio_core_add+reg_offset), gpio_reg);
- gpio_reg = in32(GPIO_TS(gpio_core_add+reg_offset))
- & ~(GPIO_MASK >> (j*2));
- gpio_reg = gpio_reg | (GPIO_ALT1_SEL >> (j*2));
- out32(GPIO_TS(gpio_core_add+reg_offset), gpio_reg);
- break;
-
- case GPIO_ALT2:
- gpio_reg = in32(GPIO_OS(gpio_core_add+reg_offset))
- & ~(GPIO_MASK >> (j*2));
- gpio_reg = gpio_reg | (GPIO_ALT2_SEL >> (j*2));
- out32(GPIO_OS(gpio_core_add+reg_offset), gpio_reg);
- gpio_reg = in32(GPIO_TS(gpio_core_add+reg_offset))
- & ~(GPIO_MASK >> (j*2));
- gpio_reg = gpio_reg | (GPIO_ALT2_SEL >> (j*2));
- out32(GPIO_TS(gpio_core_add+reg_offset), gpio_reg);
- break;
-
- case GPIO_ALT3:
- gpio_reg = in32(GPIO_OS(gpio_core_add+reg_offset))
- & ~(GPIO_MASK >> (j*2));
- gpio_reg = gpio_reg | (GPIO_ALT3_SEL >> (j*2));
- out32(GPIO_OS(gpio_core_add+reg_offset), gpio_reg);
- gpio_reg = in32(GPIO_TS(gpio_core_add+reg_offset))
- & ~(GPIO_MASK >> (j*2));
- gpio_reg = gpio_reg | (GPIO_ALT3_SEL >> (j*2));
- out32(GPIO_TS(gpio_core_add+reg_offset), gpio_reg);
- break;
- }
- }
- }
- }
-}
-#endif /* CFG_440_GPIO_TABLE */
-
/*
* Breath some life into the CPU...
*
@@ -248,7 +137,7 @@
#endif /* CONFIG_405EP */
#if defined(CFG_440_GPIO_TABLE)
- set_chip_gpio_configuration(&gpio_tab);
+ gpio_set_chip_configuration();
#endif /* CFG_440_GPIO_TABLE */
/*
diff --git a/cpu/ppc4xx/gpio.c b/cpu/ppc4xx/gpio.c
new file mode 100644
index 0000000..dd84e58
--- /dev/null
+++ b/cpu/ppc4xx/gpio.c
@@ -0,0 +1,214 @@
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/processor.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+
+#if defined(CFG_440_GPIO_TABLE)
+gpio_param_s gpio_tab[GPIO_GROUP_MAX][GPIO_MAX] = CFG_440_GPIO_TABLE;
+#endif
+
+#if defined(GPIO0_OSRL)
+/* Only some 4xx variants support alternate funtions on the GPIO's */
+void gpio_config(int pin, int in_out, int gpio_alt, int out_val)
+{
+ u32 mask;
+ u32 mask2;
+ u32 val;
+ u32 offs = 0;
+ u32 offs2 = 0;
+ int pin2 = pin << 1;
+
+ if (pin >= GPIO_MAX) {
+ offs = 0x100;
+ pin -= GPIO_MAX;
+ }
+
+ if (pin >= GPIO_MAX/2) {
+ offs2 = 0x100;
+ pin2 = (pin - GPIO_MAX/2) << 1;
+ }
+
+ mask = 0x80000000 >> pin;
+ mask2 = 0xc0000000 >> (pin2 << 1);
+
+ /* first set TCR to 0 */
+ out32(GPIO0_TCR + offs, in32(GPIO0_TCR + offs) & ~mask);
+
+ if (in_out == GPIO_OUT) {
+ val = in32(GPIO0_OSRL + offs + offs2) & ~mask2;
+ switch (gpio_alt) {
+ case GPIO_ALT1:
+ val |= GPIO_ALT1_SEL >> pin2;
+ break;
+ case GPIO_ALT2:
+ val |= GPIO_ALT2_SEL >> pin2;
+ break;
+ case GPIO_ALT3:
+ val |= GPIO_ALT3_SEL >> pin2;
+ break;
+ }
+ out32(GPIO0_OSRL + offs + offs2, val);
+
+ /* setup requested output value */
+ if (out_val == GPIO_OUT_0)
+ out32(GPIO0_OR + offs, in32(GPIO0_OR + offs) & ~mask);
+ else if (out_val == GPIO_OUT_1)
+ out32(GPIO0_OR + offs, in32(GPIO0_OR + offs) | mask);
+
+ /* now configure TCR to drive output if selected */
+ out32(GPIO0_TCR + offs, in32(GPIO0_TCR + offs) | mask);
+ } else {
+ val = in32(GPIO0_ISR1L + offs + offs2) & ~mask2;
+ val |= GPIO_IN_SEL >> pin2;
+ out32(GPIO0_ISR1L + offs + offs2, val);
+ }
+}
+#endif /* GPIO_OSRL */
+
+void gpio_write_bit(int pin, int val)
+{
+ u32 offs = 0;
+
+ if (pin >= GPIO_MAX) {
+ offs = 0x100;
+ pin -= GPIO_MAX;
+ }
+
+ if (val)
+ out32(GPIO0_OR + offs, in32(GPIO0_OR + offs) | GPIO_VAL(pin));
+ else
+ out32(GPIO0_OR + offs, in32(GPIO0_OR + offs) & ~GPIO_VAL(pin));
+}
+
+#if defined(CFG_440_GPIO_TABLE)
+void gpio_set_chip_configuration(void)
+{
+ unsigned char i=0, j=0, offs=0, gpio_core;
+ unsigned long reg, core_add;
+
+ for (gpio_core=0; gpio_core<GPIO_GROUP_MAX; gpio_core++) {
+ j = 0;
+ offs = 0;
+ /* GPIO config of the GPIOs 0 to 31 */
+ for (i=0; i<GPIO_MAX; i++, j++) {
+ if (i == GPIO_MAX/2) {
+ offs = 4;
+ j = i-16;
+ }
+
+ core_add = gpio_tab[gpio_core][i].add;
+
+ if ((gpio_tab[gpio_core][i].in_out == GPIO_IN) ||
+ (gpio_tab[gpio_core][i].in_out == GPIO_BI)) {
+
+ switch (gpio_tab[gpio_core][i].alt_nb) {
+ case GPIO_SEL:
+ break;
+
+ case GPIO_ALT1:
+ reg = in32(GPIO_IS1(core_add+offs))
+ & ~(GPIO_MASK >> (j*2));
+ reg = reg | (GPIO_IN_SEL >> (j*2));
+ out32(GPIO_IS1(core_add+offs), reg);
+ break;
+
+ case GPIO_ALT2:
+ reg = in32(GPIO_IS2(core_add+offs))
+ & ~(GPIO_MASK >> (j*2));
+ reg = reg | (GPIO_IN_SEL >> (j*2));
+ out32(GPIO_IS2(core_add+offs), reg);
+ break;
+
+ case GPIO_ALT3:
+ reg = in32(GPIO_IS3(core_add+offs))
+ & ~(GPIO_MASK >> (j*2));
+ reg = reg | (GPIO_IN_SEL >> (j*2));
+ out32(GPIO_IS3(core_add+offs), reg);
+ break;
+ }
+ }
+
+ if ((gpio_tab[gpio_core][i].in_out == GPIO_OUT) ||
+ (gpio_tab[gpio_core][i].in_out == GPIO_BI)) {
+
+ switch (gpio_tab[gpio_core][i].alt_nb) {
+ case GPIO_SEL:
+ if (gpio_core == GPIO0) {
+ reg = in32(GPIO0_TCR) | (0x80000000 >> (j));
+ out32(GPIO0_TCR, reg);
+ }
+
+ if (gpio_core == GPIO1) {
+ reg = in32(GPIO1_TCR) | (0x80000000 >> (j));
+ out32(GPIO1_TCR, reg);
+ }
+
+ reg = in32(GPIO_OS(core_add+offs))
+ & ~(GPIO_MASK >> (j*2));
+ out32(GPIO_OS(core_add+offs), reg);
+ reg = in32(GPIO_TS(core_add+offs))
+ & ~(GPIO_MASK >> (j*2));
+ out32(GPIO_TS(core_add+offs), reg);
+ break;
+
+ case GPIO_ALT1:
+ reg = in32(GPIO_OS(core_add+offs))
+ & ~(GPIO_MASK >> (j*2));
+ reg = reg | (GPIO_ALT1_SEL >> (j*2));
+ out32(GPIO_OS(core_add+offs), reg);
+ reg = in32(GPIO_TS(core_add+offs))
+ & ~(GPIO_MASK >> (j*2));
+ reg = reg | (GPIO_ALT1_SEL >> (j*2));
+ out32(GPIO_TS(core_add+offs), reg);
+ break;
+
+ case GPIO_ALT2:
+ reg = in32(GPIO_OS(core_add+offs))
+ & ~(GPIO_MASK >> (j*2));
+ reg = reg | (GPIO_ALT2_SEL >> (j*2));
+ out32(GPIO_OS(core_add+offs), reg);
+ reg = in32(GPIO_TS(core_add+offs))
+ & ~(GPIO_MASK >> (j*2));
+ reg = reg | (GPIO_ALT2_SEL >> (j*2));
+ out32(GPIO_TS(core_add+offs), reg);
+ break;
+
+ case GPIO_ALT3:
+ reg = in32(GPIO_OS(core_add+offs))
+ & ~(GPIO_MASK >> (j*2));
+ reg = reg | (GPIO_ALT3_SEL >> (j*2));
+ out32(GPIO_OS(core_add+offs), reg);
+ reg = in32(GPIO_TS(core_add+offs))
+ & ~(GPIO_MASK >> (j*2));
+ reg = reg | (GPIO_ALT3_SEL >> (j*2));
+ out32(GPIO_TS(core_add+offs), reg);
+ break;
+ }
+ }
+ }
+ }
+}
+#endif /* CFG_440_GPIO_TABLE */
diff --git a/cpu/ppc4xx/i2c.c b/cpu/ppc4xx/i2c.c
index 8f4da86..47c264e 100644
--- a/cpu/ppc4xx/i2c.c
+++ b/cpu/ppc4xx/i2c.c
@@ -91,7 +91,6 @@
void i2c_init(int speed, int slaveadd)
{
- sys_info_t sysInfo;
unsigned long freqOPB;
int val, divisor;
int bus;
@@ -124,8 +123,7 @@
/* Clock divide Register */
/* get OPB frequency */
- get_sys_info(&sysInfo);
- freqOPB = sysInfo.freqPLB / sysInfo.pllOpbDiv;
+ freqOPB = get_OPB_freq();
/* set divisor according to freqOPB */
divisor = (freqOPB - 1) / 10000000;
if (divisor == 0)
diff --git a/cpu/ppc4xx/start.S b/cpu/ppc4xx/start.S
index d918b3e..a96083c 100644
--- a/cpu/ppc4xx/start.S
+++ b/cpu/ppc4xx/start.S
@@ -2,6 +2,7 @@
* Copyright (C) 1998 Dan Malek <dmalek@jlc.net>
* Copyright (C) 1999 Magnus Damm <kieraypc01.p.y.kie.era.ericsson.se>
* Copyright (C) 2000,2001,2002 Wolfgang Denk <wd@denx.de>
+ * Copyright (C) 2007 Stefan Roese <sr@denx.de>, DENX Software Engineering
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -757,7 +758,6 @@
#endif /* CONFIG_405EP */
#if defined(CFG_OCM_DATA_ADDR) && defined(CFG_OCM_DATA_SIZE)
-/* test-only... (clean up later when NAND booting is supported) */
#if defined(CONFIG_405EZ)
/********************************************************************
* Setup OCM - On Chip Memory - PPC405EZ uses OCM Controller V2
@@ -786,41 +786,7 @@
mtdcr ocmdsisdpc,r4
isync
-
-#if defined(CONFIG_NAND_SPL)
- /*
- * 405EZ can boot from NAND Flash.
- * If we are booting the SPL (Pre-loader), copy code from
- * the mapped 4K NAND Flash to the OCM
- */
- li r4,(CFG_NAND_BOOT_SPL_SIZE >> 2) - 1
- mtctr r4
- lis r2,CFG_NAND_BOOT_SPL_SRC@h
- ori r2,r2,CFG_NAND_BOOT_SPL_SRC@l
- lis r3,CFG_NAND_BOOT_SPL_DST@h
- ori r3,r3,CFG_NAND_BOOT_SPL_DST@l
-spl_loop:
- lwzu r4,4(r2)
- stwu r4,4(r3)
- bdnz spl_loop
-
- /*
- * Jump to code in OCM Ram
- */
- bl 00f
-00: mflr r10
- lis r3,(CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)@h
- ori r3,r3,(CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)@l
- sub r10,r10,r3
- addi r10,r10,28
- mtlr r10
- blr
-start_ram:
- sync
- isync
-#endif
-#else
-/* ...test-only */
+#else /* CONFIG_405EZ */
/********************************************************************
* Setup OCM - On Chip Memory
*******************************************************************/
@@ -828,14 +794,15 @@
lis r0, 0x7FFF
ori r0, r0, 0xFFFF
mfdcr r3, ocmiscntl /* get instr-side IRAM config */
- mfdcr r4, ocmdscntl /* get data-side IRAM config */
- and r3, r3, r0 /* disable data-side IRAM */
- and r4, r4, r0 /* disable data-side IRAM */
- mtdcr ocmiscntl, r3 /* set instr-side IRAM config */
- mtdcr ocmdscntl, r4 /* set data-side IRAM config */
+ mfdcr r4, ocmdscntl /* get data-side IRAM config */
+ and r3, r3, r0 /* disable data-side IRAM */
+ and r4, r4, r0 /* disable data-side IRAM */
+ mtdcr ocmiscntl, r3 /* set instr-side IRAM config */
+ mtdcr ocmdscntl, r4 /* set data-side IRAM config */
isync
- addis r3, 0, CFG_OCM_DATA_ADDR@h /* OCM location */
+ lis r3,CFG_OCM_DATA_ADDR@h /* OCM location */
+ ori r3,r3,CFG_OCM_DATA_ADDR@l
mtdcr ocmdsarc, r3
addis r4, 0, 0xC000 /* OCM data area enabled */
mtdcr ocmdscntl, r4
@@ -1925,11 +1892,11 @@
#endif /* CONFIG_405EP */
#if defined(CONFIG_440)
-#define function_prolog(func_name) .text; \
+#define function_prolog(func_name) .text; \
.align 2; \
.globl func_name; \
func_name:
-#define function_epilog(func_name) .type func_name,@function; \
+#define function_epilog(func_name) .type func_name,@function; \
.size func_name,.-func_name
/*----------------------------------------------------------------------------+
@@ -1985,13 +1952,13 @@
+----------------------------------------------------------------------------*/
function_prolog(dcbz_area)
rlwinm. r5,r4,0,27,31
- rlwinm r5,r4,27,5,31
- beq ..d_ra2
- addi r5,r5,0x0001
-..d_ra2:mtctr r5
-..d_ag2:dcbz r0,r3
- addi r3,r3,32
- bdnz ..d_ag2
+ rlwinm r5,r4,27,5,31
+ beq ..d_ra2
+ addi r5,r5,0x0001
+..d_ra2:mtctr r5
+..d_ag2:dcbz r0,r3
+ addi r3,r3,32
+ bdnz ..d_ag2
sync
blr
function_epilog(dcbz_area)
@@ -2000,26 +1967,26 @@
| dflush. Assume 32K at vector address is cachable.
+----------------------------------------------------------------------------*/
function_prolog(dflush)
- mfmsr r9
- rlwinm r8,r9,0,15,13
- rlwinm r8,r8,0,17,15
- mtmsr r8
- addi r3,r0,0x0000
- mtspr dvlim,r3
- mfspr r3,ivpr
- addi r4,r0,1024
- mtctr r4
+ mfmsr r9
+ rlwinm r8,r9,0,15,13
+ rlwinm r8,r8,0,17,15
+ mtmsr r8
+ addi r3,r0,0x0000
+ mtspr dvlim,r3
+ mfspr r3,ivpr
+ addi r4,r0,1024
+ mtctr r4
..dflush_loop:
- lwz r6,0x0(r3)
- addi r3,r3,32
- bdnz ..dflush_loop
- addi r3,r3,-32
- mtctr r4
-..ag: dcbf r0,r3
- addi r3,r3,-32
- bdnz ..ag
+ lwz r6,0x0(r3)
+ addi r3,r3,32
+ bdnz ..dflush_loop
+ addi r3,r3,-32
+ mtctr r4
+..ag: dcbf r0,r3
+ addi r3,r3,-32
+ bdnz ..ag
sync
- mtmsr r9
+ mtmsr r9
blr
function_epilog(dflush)
#endif /* CONFIG_440 */
diff --git a/disk/part.c b/disk/part.c
index 9e8bd4f..acc1a74 100644
--- a/disk/part.c
+++ b/disk/part.c
@@ -179,6 +179,7 @@
#if ((CONFIG_COMMANDS & CFG_CMD_IDE) || \
(CONFIG_COMMANDS & CFG_CMD_SCSI) || \
(CONFIG_COMMANDS & CFG_CMD_USB) || \
+ defined(CONFIG_MMC) || \
defined(CONFIG_SYSTEMACE) )
#if defined(CONFIG_MAC_PARTITION) || \
diff --git a/doc/README.Lite5200B_low_power b/doc/README.Lite5200B_low_power
new file mode 100644
index 0000000..5b04fbb
--- /dev/null
+++ b/doc/README.Lite5200B_low_power
@@ -0,0 +1,22 @@
+Lite5200B wakeup from low-power mode (CONFIG_LITE5200B_PM)
+----------------------------------------------------------
+
+Low-power mode as described in Lite5200B User's Manual, means that
+with support of MC68HLC908QT1 microcontroller (refered to as QT),
+everything but the SDRAM can be powered down. This brings
+maximum power saving, while one can still restore previous state
+quickly.
+
+Quick overview where U-Boot comes into the picture:
+- OS saves device states
+- OS saves wakeup handler address to physical 0x0, puts SDRAM into
+ self-refresh and signals to QT, it should power down the board
+- / board is sleeping here /
+- someone presses SW4 (connected to QT)
+- U-Boot checks PSC2_4 pin, if QT drives it down, then we woke up,
+ so get SDRAM out of self-refresh and transfer control to OS
+ wakeup handler
+- OS restores device states
+
+This was tested on Linux with USB and Ethernet in use. Adding
+support for other devices is an OS issue.
diff --git a/doc/README.NetConsole b/doc/README.NetConsole
index cc35a0a..fea8e33 100644
--- a/doc/README.NetConsole
+++ b/doc/README.NetConsole
@@ -38,6 +38,11 @@
target IP address (or host name, assuming DNS is working). The script
can be interrupted by pressing ^T (CTRL-T).
+Be aware that in some distributives (Fedora Core 5 at least)
+usage of nc has been changed and -l and -p options are considered
+as mutually exclusive. If nc complains about options provided,
+you can just remove the -p option from the script.
+
It turns out that 'netcat' cannot be used to listen to broadcast
packets. We developed our own tool 'ncb' (see tools directory) that
listens to broadcast packets on a given port and dumps them to the
diff --git a/doc/README.mpc7448hpc2 b/doc/README.mpc7448hpc2
new file mode 100644
index 0000000..8659e83
--- /dev/null
+++ b/doc/README.mpc7448hpc2
@@ -0,0 +1,184 @@
+Freescale MPC7448hpc2 (Taiga) board
+===================================
+
+Created 08/11/2006 Roy Zang
+--------------------------
+MPC7448hpc2 (Taiga) board is a high-performance PowerPC server reference
+design, which is optimized for high speed throughput between the processor and
+the memory, disk drive and Ethernet port subsystems.
+
+MPC7448hpc2(Taiga) is designed to the micro-ATX chassis, allowing it to be
+used in 1U or 2U rack-mount chassis¡¯, as well as in standard ATX/Micro-ATX
+chassis.
+
+Building U-Boot
+------------------
+The mpc7448hpc2 code base is known to compile using:
+ Binutils 2.15, Gcc 3.4.3, Glibc 2.3.3
+
+ $ make mpc7448hpc2_config
+ Configuring for mpc7448hpc2 board...
+
+ $ make
+
+Memory Map
+----------
+
+The memory map is setup for Linux to operate properly.
+
+The mapping is:
+
+ Range Start Range End Definition Size
+
+ 0x0000_0000 0x7fff_ffff DDR 2G
+ 0xe000_0000 0xe7ff_ffff PCI Memory 128M
+ 0xfa00_0000 0xfaff_ffff PCI IO 16M
+ 0xfb00_0000 0xfbff_ffff PCI Config 16M
+ 0xfc00_0000 0xfc0f_ffff NVRAM/CADMUS 1M
+ 0xfe00_0000 0xfeff_ffff PromJet 16M
+ 0xff00_0000 0xff80_0000 FLASH (boot flash) 8M
+ 0xff80_0000 0xffff_ffff FLASH (second half flash) 8M
+
+Using Flash
+-----------
+
+The MPC7448hpc2 board has two "banks" of flash, each 8MB in size
+(2^23 = 0x00800000).
+
+Note: the "bank" here refers to half of the flash. In fact, there is only one
+bank of flash, which is divided into low and high half. Each is controlled by
+the most significant bit of the address bus. The so called "bank" is only for
+convenience.
+
+There is a switch which allows the "bank" to be selected. The switch
+settings for updating flash are given below.
+
+The u-boot commands for copying the boot-bank into the secondary bank are
+as follows:
+
+ erase ff800000 ff880000
+ cp.b ff000000 ff800000 80000
+
+U-boot commands for downloading an image via tftp and flashing
+it into the secondary bank:
+
+ tftp 10000 <u-boot.bin.image>
+ erase ff000000 ff080000
+ cp.b 10000 ff000000 80000
+
+After copying the image into the second bank of flash, be sure to toggle
+SW3[4] on board before resetting the board in order to set the
+secondary bank as the boot-bank.
+
+Board Switches
+----------------------
+
+Most switches on the board should not be changed. The most frequent
+user-settable switches on the board are used to configure
+the flash banks and determining the PCI frequency.
+
+SW1[1-5]: Processor core voltage
+
+ 12345 Core Voltage
+ -----
+ SW1=01111 1.000V.
+ SW1=01101 1.100V.
+ SW1=01011 1.200V.
+ SW1=01001 1.300V only for MPC7447A.
+
+
+SW2[1-6]: CPU core frequency
+
+ CPU Core Frequency (MHz)
+ Bus Frequency
+ 123456 100 133 167 200 Ratio
+
+ ------
+ SW2=101100 500 667 833 1000 5x
+ SW2=100100 550 733 917 1100 5.5x
+ SW2=110100 600 800 1000 1200 6x
+ SW2=010100 650 866 1083 1300 6.5x
+ SW2=001000 700 930 1167 1400 7x
+ SW2=000100 750 1000 1250 1500 7.5x
+ SW2=110000 800 1066 1333 1600 8x
+ SW2=011000 850 1333 1417 1700 8.5x only for MPC7447A
+ SW2=011110 900 1200 1500 1800 9x
+
+This table shows only a subset of available frequency options; see the CPU
+hardware specifications for more information.
+
+SW2[7-8]: Bus Protocol and CPU Reset Option
+
+ 7
+ -
+ SW2=0 System bus uses MPX bus protocol
+ SW2=1 System bus uses 60x bus protocol
+
+ 8
+ -
+ SW2=0 TSI108 can cause CPU reset
+ SW2=1 TSI108 can not cause CPU reset
+
+SW3[1-8] system options
+
+ 123
+ ---
+ SW3=xxx Connected to GPIO[0:2] on TSI108
+
+ 4
+ -
+ SW3=0 CPU boots from low half of flash
+ SW3=1 CPU boots from high half of flash
+
+ 5
+ -
+ SW3=0 SATA and slot2 connected to PCI bus
+ SW3=1 Only slot1 connected to PCI bus
+
+ 6
+ -
+ SW3=0 USB connected to PCI bus
+ SW3=1 USB disconnected from PCI bus
+
+ 7
+ -
+ SW3=0 Flash is write protected
+ SW3=1 Flash is NOT write protected
+
+ 8
+ -
+ SW3=0 CPU will boot from flash
+ SW3=1 CPU will boot from PromJet
+
+SW4[1-3]: System bus frequency
+
+ Bus Frequency (MHz)
+ ---
+ SW4=010 183
+ SW4=011 100
+ SW4=100 133
+ SW4=101 166 only for MPC7447A
+ SW4=110 200 only for MPC7448
+ others reserved
+
+SW4[4-6]: DDR2 SDRAM frequency
+
+ Bus Frequency (MHz)
+ ---
+ SW4=000 external clock
+ SW4=011 system clock
+ SW4=100 133
+ SW4=101 166
+ SW4=110 200
+ others reserved
+
+SW4[7-8]: PCI/PCI-X frequency control
+ 7
+ -
+ SW4=0 PCI/PCI-X bus operates normally
+ SW4=1 PCI bus forced to PCI-33 mode
+
+ 8
+ -
+ SW4=0 PCI-X mode at 133 MHz allowed
+ SW4=1 PCI-X mode limited to 100 MHz
diff --git a/drivers/Makefile b/drivers/Makefile
index fffc22a..d68cba6 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -32,7 +32,7 @@
cs8900.o ct69000.o dataflash.o dc2114x.o dm9000x.o \
e1000.o eepro100.o \
i8042.o inca-ip_sw.o keyboard.o \
- lan91c96.o \
+ lan91c96.o macb.o \
natsemi.o ne2000.o netarm_eth.o netconsole.o \
ns16550.o ns8382x.o ns87308.o ns7520_eth.o omap1510_i2c.o \
omap24xx_i2c.o pci.o pci_auto.o pci_indirect.o \
@@ -46,6 +46,7 @@
sl811_usb.o sm501.o smc91111.o smiLynxEM.o \
status_led.o sym53c8xx.o systemace.o ahci.o \
ti_pci1410a.o tigon3.o tsec.o \
+ tsi108_eth.o tsi108_i2c.o tsi108_pci.o \
usbdcore.o usbdcore_ep0.o usbdcore_omap1510.o usbtty.o \
videomodes.o w83c553f.o \
ks8695eth.o \
diff --git a/drivers/atmel_usart.c b/drivers/atmel_usart.c
index 41c3768..f35b997 100644
--- a/drivers/atmel_usart.c
+++ b/drivers/atmel_usart.c
@@ -19,7 +19,22 @@
#ifdef CONFIG_ATMEL_USART
#include <asm/io.h>
-#include <asm/arch/platform.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/memory-map.h>
+
+#if defined(CONFIG_USART0)
+# define USART_ID 0
+# define USART_BASE USART0_BASE
+#elif defined(CONFIG_USART1)
+# define USART_ID 1
+# define USART_BASE USART1_BASE
+#elif defined(CONFIG_USART2)
+# define USART_ID 2
+# define USART_BASE USART2_BASE
+#elif defined(CONFIG_USART3)
+# define USART_ID 3
+# define USART_BASE USART3_BASE
+#endif
#include "atmel_usart.h"
@@ -35,26 +50,23 @@
* Baud Rate = --------------
* 16 * CD
*/
- usart_hz = pm_get_clock_freq(gd->console_uart->resource[0].u.clock.id);
+ usart_hz = get_usart_clk_rate(USART_ID);
divisor = (usart_hz / 16 + gd->baudrate / 2) / gd->baudrate;
- usart3_writel(gd->console_uart, BRGR, USART3_BF(CD, divisor));
+ usart3_writel(BRGR, USART3_BF(CD, divisor));
}
int serial_init(void)
{
- usart3_writel(gd->console_uart, CR,
- USART3_BIT(RSTRX) | USART3_BIT(RSTTX));
+ usart3_writel(CR, USART3_BIT(RSTRX) | USART3_BIT(RSTTX));
serial_setbrg();
- usart3_writel(gd->console_uart, CR,
- USART3_BIT(RXEN) | USART3_BIT(TXEN));
- usart3_writel(gd->console_uart, MR,
- USART3_BF(USART_MODE, USART3_USART_MODE_NORMAL)
- | USART3_BF(USCLKS, USART3_USCLKS_MCK)
- | USART3_BF(CHRL, USART3_CHRL_8)
- | USART3_BF(PAR, USART3_PAR_NONE)
- | USART3_BF(NBSTOP, USART3_NBSTOP_1));
+ usart3_writel(CR, USART3_BIT(RXEN) | USART3_BIT(TXEN));
+ usart3_writel(MR, (USART3_BF(USART_MODE, USART3_USART_MODE_NORMAL)
+ | USART3_BF(USCLKS, USART3_USCLKS_MCK)
+ | USART3_BF(CHRL, USART3_CHRL_8)
+ | USART3_BF(PAR, USART3_PAR_NONE)
+ | USART3_BF(NBSTOP, USART3_NBSTOP_1)));
return 0;
}
@@ -64,8 +76,8 @@
if (c == '\n')
serial_putc('\r');
- while (!(usart3_readl(gd->console_uart, CSR) & USART3_BIT(TXRDY))) ;
- usart3_writel(gd->console_uart, THR, c);
+ while (!(usart3_readl(CSR) & USART3_BIT(TXRDY))) ;
+ usart3_writel(THR, c);
}
void serial_puts(const char *s)
@@ -76,13 +88,13 @@
int serial_getc(void)
{
- while (!(usart3_readl(gd->console_uart, CSR) & USART3_BIT(RXRDY))) ;
- return usart3_readl(gd->console_uart, RHR);
+ while (!(usart3_readl(CSR) & USART3_BIT(RXRDY))) ;
+ return usart3_readl(RHR);
}
int serial_tstc(void)
{
- return (usart3_readl(gd->console_uart, CSR) & USART3_BIT(RXRDY)) != 0;
+ return (usart3_readl(CSR) & USART3_BIT(RXRDY)) != 0;
}
#endif /* CONFIG_ATMEL_USART */
diff --git a/drivers/atmel_usart.h b/drivers/atmel_usart.h
index fad90a8..af3773a 100644
--- a/drivers/atmel_usart.h
+++ b/drivers/atmel_usart.h
@@ -306,9 +306,9 @@
| USART3_BF(name,value))
/* Register access macros */
-#define usart3_readl(port,reg) \
- readl((port)->regs + USART3_##reg)
-#define usart3_writel(port,reg,value) \
- writel((value), (port)->regs + USART3_##reg)
+#define usart3_readl(reg) \
+ readl((void *)USART_BASE + USART3_##reg)
+#define usart3_writel(reg,value) \
+ writel((value), (void *)USART_BASE + USART3_##reg)
#endif /* __DRIVERS_ATMEL_USART_H__ */
diff --git a/drivers/macb.c b/drivers/macb.c
new file mode 100644
index 0000000..186ab19
--- /dev/null
+++ b/drivers/macb.c
@@ -0,0 +1,575 @@
+/*
+ * Copyright (C) 2005-2006 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#include <common.h>
+
+#if defined(CONFIG_MACB) && (CONFIG_COMMANDS & (CFG_CMD_NET | CFG_CMD_MII))
+
+/*
+ * The u-boot networking stack is a little weird. It seems like the
+ * networking core allocates receive buffers up front without any
+ * regard to the hardware that's supposed to actually receive those
+ * packets.
+ *
+ * The MACB receives packets into 128-byte receive buffers, so the
+ * buffers allocated by the core isn't very practical to use. We'll
+ * allocate our own, but we need one such buffer in case a packet
+ * wraps around the DMA ring so that we have to copy it.
+ *
+ * Therefore, define CFG_RX_ETH_BUFFER to 1 in the board-specific
+ * configuration header. This way, the core allocates one RX buffer
+ * and one TX buffer, each of which can hold a ethernet packet of
+ * maximum size.
+ *
+ * For some reason, the networking core unconditionally specifies a
+ * 32-byte packet "alignment" (which really should be called
+ * "padding"). MACB shouldn't need that, but we'll refrain from any
+ * core modifications here...
+ */
+
+#include <net.h>
+#include <malloc.h>
+
+#include <linux/mii.h>
+#include <asm/io.h>
+#include <asm/dma-mapping.h>
+#include <asm/arch/clk.h>
+
+#include "macb.h"
+
+#define CFG_MACB_RX_BUFFER_SIZE 4096
+#define CFG_MACB_RX_RING_SIZE (CFG_MACB_RX_BUFFER_SIZE / 128)
+#define CFG_MACB_TX_RING_SIZE 16
+#define CFG_MACB_TX_TIMEOUT 1000
+#define CFG_MACB_AUTONEG_TIMEOUT 5000000
+
+struct macb_dma_desc {
+ u32 addr;
+ u32 ctrl;
+};
+
+#define RXADDR_USED 0x00000001
+#define RXADDR_WRAP 0x00000002
+
+#define RXBUF_FRMLEN_MASK 0x00000fff
+#define RXBUF_FRAME_START 0x00004000
+#define RXBUF_FRAME_END 0x00008000
+#define RXBUF_TYPEID_MATCH 0x00400000
+#define RXBUF_ADDR4_MATCH 0x00800000
+#define RXBUF_ADDR3_MATCH 0x01000000
+#define RXBUF_ADDR2_MATCH 0x02000000
+#define RXBUF_ADDR1_MATCH 0x04000000
+#define RXBUF_BROADCAST 0x80000000
+
+#define TXBUF_FRMLEN_MASK 0x000007ff
+#define TXBUF_FRAME_END 0x00008000
+#define TXBUF_NOCRC 0x00010000
+#define TXBUF_EXHAUSTED 0x08000000
+#define TXBUF_UNDERRUN 0x10000000
+#define TXBUF_MAXRETRY 0x20000000
+#define TXBUF_WRAP 0x40000000
+#define TXBUF_USED 0x80000000
+
+struct macb_device {
+ void *regs;
+
+ unsigned int rx_tail;
+ unsigned int tx_head;
+ unsigned int tx_tail;
+
+ void *rx_buffer;
+ void *tx_buffer;
+ struct macb_dma_desc *rx_ring;
+ struct macb_dma_desc *tx_ring;
+
+ unsigned long rx_buffer_dma;
+ unsigned long rx_ring_dma;
+ unsigned long tx_ring_dma;
+
+ const struct device *dev;
+ struct eth_device netdev;
+ unsigned short phy_addr;
+};
+#define to_macb(_nd) container_of(_nd, struct macb_device, netdev)
+
+static void macb_mdio_write(struct macb_device *macb, u8 reg, u16 value)
+{
+ unsigned long netctl;
+ unsigned long netstat;
+ unsigned long frame;
+
+ netctl = macb_readl(macb, NCR);
+ netctl |= MACB_BIT(MPE);
+ macb_writel(macb, NCR, netctl);
+
+ frame = (MACB_BF(SOF, 1)
+ | MACB_BF(RW, 1)
+ | MACB_BF(PHYA, macb->phy_addr)
+ | MACB_BF(REGA, reg)
+ | MACB_BF(CODE, 2)
+ | MACB_BF(DATA, value));
+ macb_writel(macb, MAN, frame);
+
+ do {
+ netstat = macb_readl(macb, NSR);
+ } while (!(netstat & MACB_BIT(IDLE)));
+
+ netctl = macb_readl(macb, NCR);
+ netctl &= ~MACB_BIT(MPE);
+ macb_writel(macb, NCR, netctl);
+}
+
+static u16 macb_mdio_read(struct macb_device *macb, u8 reg)
+{
+ unsigned long netctl;
+ unsigned long netstat;
+ unsigned long frame;
+
+ netctl = macb_readl(macb, NCR);
+ netctl |= MACB_BIT(MPE);
+ macb_writel(macb, NCR, netctl);
+
+ frame = (MACB_BF(SOF, 1)
+ | MACB_BF(RW, 2)
+ | MACB_BF(PHYA, macb->phy_addr)
+ | MACB_BF(REGA, reg)
+ | MACB_BF(CODE, 2));
+ macb_writel(macb, MAN, frame);
+
+ do {
+ netstat = macb_readl(macb, NSR);
+ } while (!(netstat & MACB_BIT(IDLE)));
+
+ frame = macb_readl(macb, MAN);
+
+ netctl = macb_readl(macb, NCR);
+ netctl &= ~MACB_BIT(MPE);
+ macb_writel(macb, NCR, netctl);
+
+ return MACB_BFEXT(DATA, frame);
+}
+
+#if (CONFIG_COMMANDS & CFG_CMD_NET)
+
+static int macb_send(struct eth_device *netdev, volatile void *packet,
+ int length)
+{
+ struct macb_device *macb = to_macb(netdev);
+ unsigned long paddr, ctrl;
+ unsigned int tx_head = macb->tx_head;
+ int i;
+
+ paddr = dma_map_single(packet, length, DMA_TO_DEVICE);
+
+ ctrl = length & TXBUF_FRMLEN_MASK;
+ ctrl |= TXBUF_FRAME_END;
+ if (tx_head == (CFG_MACB_TX_RING_SIZE - 1)) {
+ ctrl |= TXBUF_WRAP;
+ macb->tx_head = 0;
+ } else
+ macb->tx_head++;
+
+ macb->tx_ring[tx_head].ctrl = ctrl;
+ macb->tx_ring[tx_head].addr = paddr;
+ macb_writel(macb, NCR, MACB_BIT(TE) | MACB_BIT(RE) | MACB_BIT(TSTART));
+
+ /*
+ * I guess this is necessary because the networking core may
+ * re-use the transmit buffer as soon as we return...
+ */
+ i = 0;
+ while (!(macb->tx_ring[tx_head].ctrl & TXBUF_USED)) {
+ if (i > CFG_MACB_TX_TIMEOUT) {
+ printf("%s: TX timeout\n", netdev->name);
+ break;
+ }
+ udelay(1);
+ i++;
+ }
+
+ dma_unmap_single(packet, length, paddr);
+
+ if (i <= CFG_MACB_TX_TIMEOUT) {
+ ctrl = macb->tx_ring[tx_head].ctrl;
+ if (ctrl & TXBUF_UNDERRUN)
+ printf("%s: TX underrun\n", netdev->name);
+ if (ctrl & TXBUF_EXHAUSTED)
+ printf("%s: TX buffers exhausted in mid frame\n",
+ netdev->name);
+ }
+
+ /* No one cares anyway */
+ return 0;
+}
+
+static void reclaim_rx_buffers(struct macb_device *macb,
+ unsigned int new_tail)
+{
+ unsigned int i;
+
+ i = macb->rx_tail;
+ while (i > new_tail) {
+ macb->rx_ring[i].addr &= ~RXADDR_USED;
+ i++;
+ if (i > CFG_MACB_RX_RING_SIZE)
+ i = 0;
+ }
+
+ while (i < new_tail) {
+ macb->rx_ring[i].addr &= ~RXADDR_USED;
+ i++;
+ }
+
+ macb->rx_tail = new_tail;
+}
+
+static int macb_recv(struct eth_device *netdev)
+{
+ struct macb_device *macb = to_macb(netdev);
+ unsigned int rx_tail = macb->rx_tail;
+ void *buffer;
+ int length;
+ int wrapped = 0;
+ u32 status;
+
+ for (;;) {
+ if (!(macb->rx_ring[rx_tail].addr & RXADDR_USED))
+ return -1;
+
+ status = macb->rx_ring[rx_tail].ctrl;
+ if (status & RXBUF_FRAME_START) {
+ if (rx_tail != macb->rx_tail)
+ reclaim_rx_buffers(macb, rx_tail);
+ wrapped = 0;
+ }
+
+ if (status & RXBUF_FRAME_END) {
+ buffer = macb->rx_buffer + 128 * macb->rx_tail;
+ length = status & RXBUF_FRMLEN_MASK;
+ if (wrapped) {
+ unsigned int headlen, taillen;
+
+ headlen = 128 * (CFG_MACB_RX_RING_SIZE
+ - macb->rx_tail);
+ taillen = length - headlen;
+ memcpy((void *)NetRxPackets[0],
+ buffer, headlen);
+ memcpy((void *)NetRxPackets[0] + headlen,
+ macb->rx_buffer, taillen);
+ buffer = (void *)NetRxPackets[0];
+ }
+
+ NetReceive(buffer, length);
+ if (++rx_tail >= CFG_MACB_RX_RING_SIZE)
+ rx_tail = 0;
+ reclaim_rx_buffers(macb, rx_tail);
+ } else {
+ if (++rx_tail >= CFG_MACB_RX_RING_SIZE) {
+ wrapped = 1;
+ rx_tail = 0;
+ }
+ }
+ }
+
+ return 0;
+}
+
+static int macb_phy_init(struct macb_device *macb)
+{
+ struct eth_device *netdev = &macb->netdev;
+ u32 ncfgr;
+ u16 phy_id, status, adv, lpa;
+ int media, speed, duplex;
+ int i;
+
+ /* Check if the PHY is up to snuff... */
+ phy_id = macb_mdio_read(macb, MII_PHYSID1);
+ if (phy_id == 0xffff) {
+ printf("%s: No PHY present\n", netdev->name);
+ return 0;
+ }
+
+ adv = ADVERTISE_CSMA | ADVERTISE_ALL;
+ macb_mdio_write(macb, MII_ADVERTISE, adv);
+ printf("%s: Starting autonegotiation...\n", netdev->name);
+ macb_mdio_write(macb, MII_BMCR, (BMCR_ANENABLE
+ | BMCR_ANRESTART));
+
+#if 0
+ for (i = 0; i < 9; i++)
+ printf("mii%d: 0x%04x\n", i, macb_mdio_read(macb, i));
+#endif
+
+ for (i = 0; i < CFG_MACB_AUTONEG_TIMEOUT / 100; i++) {
+ status = macb_mdio_read(macb, MII_BMSR);
+ if (status & BMSR_ANEGCOMPLETE)
+ break;
+ udelay(100);
+ }
+
+ if (status & BMSR_ANEGCOMPLETE)
+ printf("%s: Autonegotiation complete\n", netdev->name);
+ else
+ printf("%s: Autonegotiation timed out (status=0x%04x)\n",
+ netdev->name, status);
+
+ if (!(status & BMSR_LSTATUS)) {
+ for (i = 0; i < CFG_MACB_AUTONEG_TIMEOUT / 100; i++) {
+ udelay(100);
+ status = macb_mdio_read(macb, MII_BMSR);
+ if (status & BMSR_LSTATUS)
+ break;
+ }
+ }
+
+ if (!(status & BMSR_LSTATUS)) {
+ printf("%s: link down (status: 0x%04x)\n",
+ netdev->name, status);
+ return 0;
+ } else {
+ lpa = macb_mdio_read(macb, MII_LPA);
+ media = mii_nway_result(lpa & adv);
+ speed = (media & (ADVERTISE_100FULL | ADVERTISE_100HALF)
+ ? 1 : 0);
+ duplex = (media & ADVERTISE_FULL) ? 1 : 0;
+ printf("%s: link up, %sMbps %s-duplex (lpa: 0x%04x)\n",
+ netdev->name,
+ speed ? "100" : "10",
+ duplex ? "full" : "half",
+ lpa);
+
+ ncfgr = macb_readl(macb, NCFGR);
+ ncfgr &= ~(MACB_BIT(SPD) | MACB_BIT(FD));
+ if (speed)
+ ncfgr |= MACB_BIT(SPD);
+ if (duplex)
+ ncfgr |= MACB_BIT(FD);
+ macb_writel(macb, NCFGR, ncfgr);
+ return 1;
+ }
+}
+
+static int macb_init(struct eth_device *netdev, bd_t *bd)
+{
+ struct macb_device *macb = to_macb(netdev);
+ unsigned long paddr;
+ u32 hwaddr_bottom;
+ u16 hwaddr_top;
+ int i;
+
+ /*
+ * macb_halt should have been called at some point before now,
+ * so we'll assume the controller is idle.
+ */
+
+ /* initialize DMA descriptors */
+ paddr = macb->rx_buffer_dma;
+ for (i = 0; i < CFG_MACB_RX_RING_SIZE; i++) {
+ if (i == (CFG_MACB_RX_RING_SIZE - 1))
+ paddr |= RXADDR_WRAP;
+ macb->rx_ring[i].addr = paddr;
+ macb->rx_ring[i].ctrl = 0;
+ paddr += 128;
+ }
+ for (i = 0; i < CFG_MACB_TX_RING_SIZE; i++) {
+ macb->tx_ring[i].addr = 0;
+ if (i == (CFG_MACB_TX_RING_SIZE - 1))
+ macb->tx_ring[i].ctrl = TXBUF_USED | TXBUF_WRAP;
+ else
+ macb->tx_ring[i].ctrl = TXBUF_USED;
+ }
+ macb->rx_tail = macb->tx_head = macb->tx_tail = 0;
+
+ macb_writel(macb, RBQP, macb->rx_ring_dma);
+ macb_writel(macb, TBQP, macb->tx_ring_dma);
+
+ /* set hardware address */
+ hwaddr_bottom = cpu_to_le32(*((u32 *)netdev->enetaddr));
+ macb_writel(macb, SA1B, hwaddr_bottom);
+ hwaddr_top = cpu_to_le16(*((u16 *)(netdev->enetaddr + 4)));
+ macb_writel(macb, SA1T, hwaddr_top);
+
+ /* choose RMII or MII mode. This depends on the board */
+#ifdef CONFIG_RMII
+ macb_writel(macb, USRIO, 0);
+#else
+ macb_writel(macb, USRIO, MACB_BIT(MII));
+#endif
+
+ if (!macb_phy_init(macb))
+ return 0;
+
+ /* Enable TX and RX */
+ macb_writel(macb, NCR, MACB_BIT(TE) | MACB_BIT(RE));
+
+ return 1;
+}
+
+static void macb_halt(struct eth_device *netdev)
+{
+ struct macb_device *macb = to_macb(netdev);
+ u32 ncr, tsr;
+
+ /* Halt the controller and wait for any ongoing transmission to end. */
+ ncr = macb_readl(macb, NCR);
+ ncr |= MACB_BIT(THALT);
+ macb_writel(macb, NCR, ncr);
+
+ do {
+ tsr = macb_readl(macb, TSR);
+ } while (tsr & MACB_BIT(TGO));
+
+ /* Disable TX and RX, and clear statistics */
+ macb_writel(macb, NCR, MACB_BIT(CLRSTAT));
+}
+
+int macb_eth_initialize(int id, void *regs, unsigned int phy_addr)
+{
+ struct macb_device *macb;
+ struct eth_device *netdev;
+ unsigned long macb_hz;
+ u32 ncfgr;
+
+ macb = malloc(sizeof(struct macb_device));
+ if (!macb) {
+ printf("Error: Failed to allocate memory for MACB%d\n", id);
+ return -1;
+ }
+ memset(macb, 0, sizeof(struct macb_device));
+
+ netdev = &macb->netdev;
+
+ macb->rx_buffer = dma_alloc_coherent(CFG_MACB_RX_BUFFER_SIZE,
+ &macb->rx_buffer_dma);
+ macb->rx_ring = dma_alloc_coherent(CFG_MACB_RX_RING_SIZE
+ * sizeof(struct macb_dma_desc),
+ &macb->rx_ring_dma);
+ macb->tx_ring = dma_alloc_coherent(CFG_MACB_TX_RING_SIZE
+ * sizeof(struct macb_dma_desc),
+ &macb->tx_ring_dma);
+
+ macb->regs = regs;
+ macb->phy_addr = phy_addr;
+
+ sprintf(netdev->name, "macb%d", id);
+ netdev->init = macb_init;
+ netdev->halt = macb_halt;
+ netdev->send = macb_send;
+ netdev->recv = macb_recv;
+
+ /*
+ * Do some basic initialization so that we at least can talk
+ * to the PHY
+ */
+ macb_hz = get_macb_pclk_rate(id);
+ if (macb_hz < 20000000)
+ ncfgr = MACB_BF(CLK, MACB_CLK_DIV8);
+ else if (macb_hz < 40000000)
+ ncfgr = MACB_BF(CLK, MACB_CLK_DIV16);
+ else if (macb_hz < 80000000)
+ ncfgr = MACB_BF(CLK, MACB_CLK_DIV32);
+ else
+ ncfgr = MACB_BF(CLK, MACB_CLK_DIV64);
+
+ macb_writel(macb, NCFGR, ncfgr);
+
+ eth_register(netdev);
+
+ return 0;
+}
+
+#endif /* (CONFIG_COMMANDS & CFG_CMD_NET) */
+
+#if (CONFIG_COMMANDS & CFG_CMD_MII)
+
+int miiphy_read(unsigned char addr, unsigned char reg, unsigned short *value)
+{
+ unsigned long netctl;
+ unsigned long netstat;
+ unsigned long frame;
+ int iflag;
+
+ iflag = disable_interrupts();
+ netctl = macb_readl(&macb, EMACB_NCR);
+ netctl |= MACB_BIT(MPE);
+ macb_writel(&macb, EMACB_NCR, netctl);
+ if (iflag)
+ enable_interrupts();
+
+ frame = (MACB_BF(SOF, 1)
+ | MACB_BF(RW, 2)
+ | MACB_BF(PHYA, addr)
+ | MACB_BF(REGA, reg)
+ | MACB_BF(CODE, 2));
+ macb_writel(&macb, EMACB_MAN, frame);
+
+ do {
+ netstat = macb_readl(&macb, EMACB_NSR);
+ } while (!(netstat & MACB_BIT(IDLE)));
+
+ frame = macb_readl(&macb, EMACB_MAN);
+ *value = MACB_BFEXT(DATA, frame);
+
+ iflag = disable_interrupts();
+ netctl = macb_readl(&macb, EMACB_NCR);
+ netctl &= ~MACB_BIT(MPE);
+ macb_writel(&macb, EMACB_NCR, netctl);
+ if (iflag)
+ enable_interrupts();
+
+ return 0;
+}
+
+int miiphy_write(unsigned char addr, unsigned char reg, unsigned short value)
+{
+ unsigned long netctl;
+ unsigned long netstat;
+ unsigned long frame;
+ int iflag;
+
+ iflag = disable_interrupts();
+ netctl = macb_readl(&macb, EMACB_NCR);
+ netctl |= MACB_BIT(MPE);
+ macb_writel(&macb, EMACB_NCR, netctl);
+ if (iflag)
+ enable_interrupts();
+
+ frame = (MACB_BF(SOF, 1)
+ | MACB_BF(RW, 1)
+ | MACB_BF(PHYA, addr)
+ | MACB_BF(REGA, reg)
+ | MACB_BF(CODE, 2)
+ | MACB_BF(DATA, value));
+ macb_writel(&macb, EMACB_MAN, frame);
+
+ do {
+ netstat = macb_readl(&macb, EMACB_NSR);
+ } while (!(netstat & MACB_BIT(IDLE)));
+
+ iflag = disable_interrupts();
+ netctl = macb_readl(&macb, EMACB_NCR);
+ netctl &= ~MACB_BIT(MPE);
+ macb_writel(&macb, EMACB_NCR, netctl);
+ if (iflag)
+ enable_interrupts();
+
+ return 0;
+}
+
+#endif /* (CONFIG_COMMANDS & CFG_CMD_MII) */
+
+#endif /* CONFIG_MACB */
diff --git a/drivers/macb.h b/drivers/macb.h
new file mode 100644
index 0000000..c778e4e
--- /dev/null
+++ b/drivers/macb.h
@@ -0,0 +1,269 @@
+/*
+ * Copyright (C) 2005-2006 Atmel Corporation
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef __DRIVERS_MACB_H__
+#define __DRIVERS_MACB_H__
+
+/* MACB register offsets */
+#define MACB_NCR 0x0000
+#define MACB_NCFGR 0x0004
+#define MACB_NSR 0x0008
+#define MACB_TSR 0x0014
+#define MACB_RBQP 0x0018
+#define MACB_TBQP 0x001c
+#define MACB_RSR 0x0020
+#define MACB_ISR 0x0024
+#define MACB_IER 0x0028
+#define MACB_IDR 0x002c
+#define MACB_IMR 0x0030
+#define MACB_MAN 0x0034
+#define MACB_PTR 0x0038
+#define MACB_PFR 0x003c
+#define MACB_FTO 0x0040
+#define MACB_SCF 0x0044
+#define MACB_MCF 0x0048
+#define MACB_FRO 0x004c
+#define MACB_FCSE 0x0050
+#define MACB_ALE 0x0054
+#define MACB_DTF 0x0058
+#define MACB_LCOL 0x005c
+#define MACB_EXCOL 0x0060
+#define MACB_TUND 0x0064
+#define MACB_CSE 0x0068
+#define MACB_RRE 0x006c
+#define MACB_ROVR 0x0070
+#define MACB_RSE 0x0074
+#define MACB_ELE 0x0078
+#define MACB_RJA 0x007c
+#define MACB_USF 0x0080
+#define MACB_STE 0x0084
+#define MACB_RLE 0x0088
+#define MACB_TPF 0x008c
+#define MACB_HRB 0x0090
+#define MACB_HRT 0x0094
+#define MACB_SA1B 0x0098
+#define MACB_SA1T 0x009c
+#define MACB_SA2B 0x00a0
+#define MACB_SA2T 0x00a4
+#define MACB_SA3B 0x00a8
+#define MACB_SA3T 0x00ac
+#define MACB_SA4B 0x00b0
+#define MACB_SA4T 0x00b4
+#define MACB_TID 0x00b8
+#define MACB_TPQ 0x00bc
+#define MACB_USRIO 0x00c0
+#define MACB_WOL 0x00c4
+
+/* Bitfields in NCR */
+#define MACB_LB_OFFSET 0
+#define MACB_LB_SIZE 1
+#define MACB_LLB_OFFSET 1
+#define MACB_LLB_SIZE 1
+#define MACB_RE_OFFSET 2
+#define MACB_RE_SIZE 1
+#define MACB_TE_OFFSET 3
+#define MACB_TE_SIZE 1
+#define MACB_MPE_OFFSET 4
+#define MACB_MPE_SIZE 1
+#define MACB_CLRSTAT_OFFSET 5
+#define MACB_CLRSTAT_SIZE 1
+#define MACB_INCSTAT_OFFSET 6
+#define MACB_INCSTAT_SIZE 1
+#define MACB_WESTAT_OFFSET 7
+#define MACB_WESTAT_SIZE 1
+#define MACB_BP_OFFSET 8
+#define MACB_BP_SIZE 1
+#define MACB_TSTART_OFFSET 9
+#define MACB_TSTART_SIZE 1
+#define MACB_THALT_OFFSET 10
+#define MACB_THALT_SIZE 1
+#define MACB_NCR_TPF_OFFSET 11
+#define MACB_NCR_TPF_SIZE 1
+#define MACB_TZQ_OFFSET 12
+#define MACB_TZQ_SIZE 1
+
+/* Bitfields in NCFGR */
+#define MACB_SPD_OFFSET 0
+#define MACB_SPD_SIZE 1
+#define MACB_FD_OFFSET 1
+#define MACB_FD_SIZE 1
+#define MACB_BIT_RATE_OFFSET 2
+#define MACB_BIT_RATE_SIZE 1
+#define MACB_JFRAME_OFFSET 3
+#define MACB_JFRAME_SIZE 1
+#define MACB_CAF_OFFSET 4
+#define MACB_CAF_SIZE 1
+#define MACB_NBC_OFFSET 5
+#define MACB_NBC_SIZE 1
+#define MACB_NCFGR_MTI_OFFSET 6
+#define MACB_NCFGR_MTI_SIZE 1
+#define MACB_UNI_OFFSET 7
+#define MACB_UNI_SIZE 1
+#define MACB_BIG_OFFSET 8
+#define MACB_BIG_SIZE 1
+#define MACB_EAE_OFFSET 9
+#define MACB_EAE_SIZE 1
+#define MACB_CLK_OFFSET 10
+#define MACB_CLK_SIZE 2
+#define MACB_RTY_OFFSET 12
+#define MACB_RTY_SIZE 1
+#define MACB_PAE_OFFSET 13
+#define MACB_PAE_SIZE 1
+#define MACB_RBOF_OFFSET 14
+#define MACB_RBOF_SIZE 2
+#define MACB_RLCE_OFFSET 16
+#define MACB_RLCE_SIZE 1
+#define MACB_DRFCS_OFFSET 17
+#define MACB_DRFCS_SIZE 1
+#define MACB_EFRHD_OFFSET 18
+#define MACB_EFRHD_SIZE 1
+#define MACB_IRXFCS_OFFSET 19
+#define MACB_IRXFCS_SIZE 1
+
+/* Bitfields in NSR */
+#define MACB_NSR_LINK_OFFSET 0
+#define MACB_NSR_LINK_SIZE 1
+#define MACB_MDIO_OFFSET 1
+#define MACB_MDIO_SIZE 1
+#define MACB_IDLE_OFFSET 2
+#define MACB_IDLE_SIZE 1
+
+/* Bitfields in TSR */
+#define MACB_UBR_OFFSET 0
+#define MACB_UBR_SIZE 1
+#define MACB_COL_OFFSET 1
+#define MACB_COL_SIZE 1
+#define MACB_TSR_RLE_OFFSET 2
+#define MACB_TSR_RLE_SIZE 1
+#define MACB_TGO_OFFSET 3
+#define MACB_TGO_SIZE 1
+#define MACB_BEX_OFFSET 4
+#define MACB_BEX_SIZE 1
+#define MACB_COMP_OFFSET 5
+#define MACB_COMP_SIZE 1
+#define MACB_UND_OFFSET 6
+#define MACB_UND_SIZE 1
+
+/* Bitfields in RSR */
+#define MACB_BNA_OFFSET 0
+#define MACB_BNA_SIZE 1
+#define MACB_REC_OFFSET 1
+#define MACB_REC_SIZE 1
+#define MACB_OVR_OFFSET 2
+#define MACB_OVR_SIZE 1
+
+/* Bitfields in ISR/IER/IDR/IMR */
+#define MACB_MFD_OFFSET 0
+#define MACB_MFD_SIZE 1
+#define MACB_RCOMP_OFFSET 1
+#define MACB_RCOMP_SIZE 1
+#define MACB_RXUBR_OFFSET 2
+#define MACB_RXUBR_SIZE 1
+#define MACB_TXUBR_OFFSET 3
+#define MACB_TXUBR_SIZE 1
+#define MACB_ISR_TUND_OFFSET 4
+#define MACB_ISR_TUND_SIZE 1
+#define MACB_ISR_RLE_OFFSET 5
+#define MACB_ISR_RLE_SIZE 1
+#define MACB_TXERR_OFFSET 6
+#define MACB_TXERR_SIZE 1
+#define MACB_TCOMP_OFFSET 7
+#define MACB_TCOMP_SIZE 1
+#define MACB_ISR_LINK_OFFSET 9
+#define MACB_ISR_LINK_SIZE 1
+#define MACB_ISR_ROVR_OFFSET 10
+#define MACB_ISR_ROVR_SIZE 1
+#define MACB_HRESP_OFFSET 11
+#define MACB_HRESP_SIZE 1
+#define MACB_PFR_OFFSET 12
+#define MACB_PFR_SIZE 1
+#define MACB_PTZ_OFFSET 13
+#define MACB_PTZ_SIZE 1
+
+/* Bitfields in MAN */
+#define MACB_DATA_OFFSET 0
+#define MACB_DATA_SIZE 16
+#define MACB_CODE_OFFSET 16
+#define MACB_CODE_SIZE 2
+#define MACB_REGA_OFFSET 18
+#define MACB_REGA_SIZE 5
+#define MACB_PHYA_OFFSET 23
+#define MACB_PHYA_SIZE 5
+#define MACB_RW_OFFSET 28
+#define MACB_RW_SIZE 2
+#define MACB_SOF_OFFSET 30
+#define MACB_SOF_SIZE 2
+
+/* Bitfields in USRIO */
+#define MACB_MII_OFFSET 0
+#define MACB_MII_SIZE 1
+#define MACB_EAM_OFFSET 1
+#define MACB_EAM_SIZE 1
+#define MACB_TX_PAUSE_OFFSET 2
+#define MACB_TX_PAUSE_SIZE 1
+#define MACB_TX_PAUSE_ZERO_OFFSET 3
+#define MACB_TX_PAUSE_ZERO_SIZE 1
+
+/* Bitfields in WOL */
+#define MACB_IP_OFFSET 0
+#define MACB_IP_SIZE 16
+#define MACB_MAG_OFFSET 16
+#define MACB_MAG_SIZE 1
+#define MACB_ARP_OFFSET 17
+#define MACB_ARP_SIZE 1
+#define MACB_SA1_OFFSET 18
+#define MACB_SA1_SIZE 1
+#define MACB_WOL_MTI_OFFSET 19
+#define MACB_WOL_MTI_SIZE 1
+
+/* Constants for CLK */
+#define MACB_CLK_DIV8 0
+#define MACB_CLK_DIV16 1
+#define MACB_CLK_DIV32 2
+#define MACB_CLK_DIV64 3
+
+/* Constants for MAN register */
+#define MACB_MAN_SOF 1
+#define MACB_MAN_WRITE 1
+#define MACB_MAN_READ 2
+#define MACB_MAN_CODE 2
+
+/* Bit manipulation macros */
+#define MACB_BIT(name) \
+ (1 << MACB_##name##_OFFSET)
+#define MACB_BF(name,value) \
+ (((value) & ((1 << MACB_##name##_SIZE) - 1)) \
+ << MACB_##name##_OFFSET)
+#define MACB_BFEXT(name,value)\
+ (((value) >> MACB_##name##_OFFSET) \
+ & ((1 << MACB_##name##_SIZE) - 1))
+#define MACB_BFINS(name,value,old) \
+ (((old) & ~(((1 << MACB_##name##_SIZE) - 1) \
+ << MACB_##name##_OFFSET)) \
+ | MACB_BF(name,value))
+
+/* Register access macros */
+#define macb_readl(port,reg) \
+ readl((port)->regs + MACB_##reg)
+#define macb_writel(port,reg,value) \
+ writel((value), (port)->regs + MACB_##reg)
+
+#endif /* __DRIVERS_MACB_H__ */
diff --git a/drivers/tsi108_eth.c b/drivers/tsi108_eth.c
new file mode 100644
index 0000000..47341be
--- /dev/null
+++ b/drivers/tsi108_eth.c
@@ -0,0 +1,1036 @@
+/***********************************************************************
+ *
+ * Copyright (c) 2005 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Description:
+ * Ethernet interface for Tundra TSI108 bridge chip
+ *
+ ***********************************************************************/
+
+#include <config.h>
+
+#if (CONFIG_COMMANDS & CFG_CMD_NET) && defined(CONFIG_NET_MULTI) \
+ && defined(CONFIG_TSI108_ETH)
+
+#if !defined(CONFIG_TSI108_ETH_NUM_PORTS) || (CONFIG_TSI108_ETH_NUM_PORTS > 2)
+#error "CONFIG_TSI108_ETH_NUM_PORTS must be defined as 1 or 2"
+#endif
+
+#include <common.h>
+#include <malloc.h>
+#include <net.h>
+#include <asm/cache.h>
+
+#ifdef DEBUG
+#define TSI108_ETH_DEBUG 7
+#else
+#define TSI108_ETH_DEBUG 0
+#endif
+
+#if TSI108_ETH_DEBUG > 0
+#define debug_lev(lev, fmt, args...) \
+if (lev <= TSI108_ETH_DEBUG) \
+printf ("%s %d: " fmt, __FUNCTION__, __LINE__, ##args)
+#else
+#define debug_lev(lev, fmt, args...) do{}while(0)
+#endif
+
+#define RX_PRINT_ERRORS
+#define TX_PRINT_ERRORS
+
+#define ETH_BASE (CFG_TSI108_CSR_BASE + 0x6000)
+
+#define ETH_PORT_OFFSET 0x400
+
+#define __REG32(base, offset) (*((volatile u32 *)((char *)(base) + (offset))))
+
+#define reg_MAC_CONFIG_1(base) __REG32(base, 0x00000000)
+#define MAC_CONFIG_1_TX_ENABLE (0x00000001)
+#define MAC_CONFIG_1_SYNC_TX_ENABLE (0x00000002)
+#define MAC_CONFIG_1_RX_ENABLE (0x00000004)
+#define MAC_CONFIG_1_SYNC_RX_ENABLE (0x00000008)
+#define MAC_CONFIG_1_TX_FLOW_CONTROL (0x00000010)
+#define MAC_CONFIG_1_RX_FLOW_CONTROL (0x00000020)
+#define MAC_CONFIG_1_LOOP_BACK (0x00000100)
+#define MAC_CONFIG_1_RESET_TX_FUNCTION (0x00010000)
+#define MAC_CONFIG_1_RESET_RX_FUNCTION (0x00020000)
+#define MAC_CONFIG_1_RESET_TX_MAC (0x00040000)
+#define MAC_CONFIG_1_RESET_RX_MAC (0x00080000)
+#define MAC_CONFIG_1_SIM_RESET (0x40000000)
+#define MAC_CONFIG_1_SOFT_RESET (0x80000000)
+
+#define reg_MAC_CONFIG_2(base) __REG32(base, 0x00000004)
+#define MAC_CONFIG_2_FULL_DUPLEX (0x00000001)
+#define MAC_CONFIG_2_CRC_ENABLE (0x00000002)
+#define MAC_CONFIG_2_PAD_CRC (0x00000004)
+#define MAC_CONFIG_2_LENGTH_CHECK (0x00000010)
+#define MAC_CONFIG_2_HUGE_FRAME (0x00000020)
+#define MAC_CONFIG_2_INTERFACE_MODE(val) (((val) & 0x3) << 8)
+#define MAC_CONFIG_2_PREAMBLE_LENGTH(val) (((val) & 0xf) << 12)
+#define INTERFACE_MODE_NIBBLE 1 /* 10/100 Mb/s MII) */
+#define INTERFACE_MODE_BYTE 2 /* 1000 Mb/s GMII/TBI */
+
+#define reg_MAXIMUM_FRAME_LENGTH(base) __REG32(base, 0x00000010)
+
+#define reg_MII_MGMT_CONFIG(base) __REG32(base, 0x00000020)
+#define MII_MGMT_CONFIG_MGMT_CLOCK_SELECT(val) ((val) & 0x7)
+#define MII_MGMT_CONFIG_NO_PREAMBLE (0x00000010)
+#define MII_MGMT_CONFIG_SCAN_INCREMENT (0x00000020)
+#define MII_MGMT_CONFIG_RESET_MGMT (0x80000000)
+
+#define reg_MII_MGMT_COMMAND(base) __REG32(base, 0x00000024)
+#define MII_MGMT_COMMAND_READ_CYCLE (0x00000001)
+#define MII_MGMT_COMMAND_SCAN_CYCLE (0x00000002)
+
+#define reg_MII_MGMT_ADDRESS(base) __REG32(base, 0x00000028)
+#define reg_MII_MGMT_CONTROL(base) __REG32(base, 0x0000002c)
+#define reg_MII_MGMT_STATUS(base) __REG32(base, 0x00000030)
+
+#define reg_MII_MGMT_INDICATORS(base) __REG32(base, 0x00000034)
+#define MII_MGMT_INDICATORS_BUSY (0x00000001)
+#define MII_MGMT_INDICATORS_SCAN (0x00000002)
+#define MII_MGMT_INDICATORS_NOT_VALID (0x00000004)
+
+#define reg_INTERFACE_STATUS(base) __REG32(base, 0x0000003c)
+#define INTERFACE_STATUS_LINK_FAIL (0x00000008)
+#define INTERFACE_STATUS_EXCESS_DEFER (0x00000200)
+
+#define reg_STATION_ADDRESS_1(base) __REG32(base, 0x00000040)
+#define reg_STATION_ADDRESS_2(base) __REG32(base, 0x00000044)
+
+#define reg_PORT_CONTROL(base) __REG32(base, 0x00000200)
+#define PORT_CONTROL_PRI (0x00000001)
+#define PORT_CONTROL_BPT (0x00010000)
+#define PORT_CONTROL_SPD (0x00040000)
+#define PORT_CONTROL_RBC (0x00080000)
+#define PORT_CONTROL_PRB (0x00200000)
+#define PORT_CONTROL_DIS (0x00400000)
+#define PORT_CONTROL_TBI (0x00800000)
+#define PORT_CONTROL_STE (0x10000000)
+#define PORT_CONTROL_ZOR (0x20000000)
+#define PORT_CONTROL_CLR (0x40000000)
+#define PORT_CONTROL_SRT (0x80000000)
+
+#define reg_TX_CONFIG(base) __REG32(base, 0x00000220)
+#define TX_CONFIG_START_Q (0x00000003)
+#define TX_CONFIG_EHP (0x00400000)
+#define TX_CONFIG_CHP (0x00800000)
+#define TX_CONFIG_RST (0x80000000)
+
+#define reg_TX_CONTROL(base) __REG32(base, 0x00000224)
+#define TX_CONTROL_GO (0x00008000)
+#define TX_CONTROL_MP (0x01000000)
+#define TX_CONTROL_EAI (0x20000000)
+#define TX_CONTROL_ABT (0x40000000)
+#define TX_CONTROL_EII (0x80000000)
+
+#define reg_TX_STATUS(base) __REG32(base, 0x00000228)
+#define TX_STATUS_QUEUE_USABLE (0x0000000f)
+#define TX_STATUS_CURR_Q (0x00000300)
+#define TX_STATUS_ACT (0x00008000)
+#define TX_STATUS_QUEUE_IDLE (0x000f0000)
+#define TX_STATUS_EOQ_PENDING (0x0f000000)
+
+#define reg_TX_EXTENDED_STATUS(base) __REG32(base, 0x0000022c)
+#define TX_EXTENDED_STATUS_END_OF_QUEUE_CONDITION (0x0000000f)
+#define TX_EXTENDED_STATUS_END_OF_FRAME_CONDITION (0x00000f00)
+#define TX_EXTENDED_STATUS_DESCRIPTOR_INTERRUPT_CONDITION (0x000f0000)
+#define TX_EXTENDED_STATUS_ERROR_FLAG (0x0f000000)
+
+#define reg_TX_THRESHOLDS(base) __REG32(base, 0x00000230)
+
+#define reg_TX_DIAGNOSTIC_ADDR(base) __REG32(base, 0x00000270)
+#define TX_DIAGNOSTIC_ADDR_INDEX (0x0000007f)
+#define TX_DIAGNOSTIC_ADDR_DFR (0x40000000)
+#define TX_DIAGNOSTIC_ADDR_AI (0x80000000)
+
+#define reg_TX_DIAGNOSTIC_DATA(base) __REG32(base, 0x00000274)
+
+#define reg_TX_ERROR_STATUS(base) __REG32(base, 0x00000278)
+#define TX_ERROR_STATUS (0x00000278)
+#define TX_ERROR_STATUS_QUEUE_0_ERROR_RESPONSE (0x0000000f)
+#define TX_ERROR_STATUS_TEA_ON_QUEUE_0 (0x00000010)
+#define TX_ERROR_STATUS_RER_ON_QUEUE_0 (0x00000020)
+#define TX_ERROR_STATUS_TER_ON_QUEUE_0 (0x00000040)
+#define TX_ERROR_STATUS_DER_ON_QUEUE_0 (0x00000080)
+#define TX_ERROR_STATUS_QUEUE_1_ERROR_RESPONSE (0x00000f00)
+#define TX_ERROR_STATUS_TEA_ON_QUEUE_1 (0x00001000)
+#define TX_ERROR_STATUS_RER_ON_QUEUE_1 (0x00002000)
+#define TX_ERROR_STATUS_TER_ON_QUEUE_1 (0x00004000)
+#define TX_ERROR_STATUS_DER_ON_QUEUE_1 (0x00008000)
+#define TX_ERROR_STATUS_QUEUE_2_ERROR_RESPONSE (0x000f0000)
+#define TX_ERROR_STATUS_TEA_ON_QUEUE_2 (0x00100000)
+#define TX_ERROR_STATUS_RER_ON_QUEUE_2 (0x00200000)
+#define TX_ERROR_STATUS_TER_ON_QUEUE_2 (0x00400000)
+#define TX_ERROR_STATUS_DER_ON_QUEUE_2 (0x00800000)
+#define TX_ERROR_STATUS_QUEUE_3_ERROR_RESPONSE (0x0f000000)
+#define TX_ERROR_STATUS_TEA_ON_QUEUE_3 (0x10000000)
+#define TX_ERROR_STATUS_RER_ON_QUEUE_3 (0x20000000)
+#define TX_ERROR_STATUS_TER_ON_QUEUE_3 (0x40000000)
+#define TX_ERROR_STATUS_DER_ON_QUEUE_3 (0x80000000)
+
+#define reg_TX_QUEUE_0_CONFIG(base) __REG32(base, 0x00000280)
+#define TX_QUEUE_0_CONFIG_OCN_PORT (0x0000003f)
+#define TX_QUEUE_0_CONFIG_BSWP (0x00000400)
+#define TX_QUEUE_0_CONFIG_WSWP (0x00000800)
+#define TX_QUEUE_0_CONFIG_AM (0x00004000)
+#define TX_QUEUE_0_CONFIG_GVI (0x00008000)
+#define TX_QUEUE_0_CONFIG_EEI (0x00010000)
+#define TX_QUEUE_0_CONFIG_ELI (0x00020000)
+#define TX_QUEUE_0_CONFIG_ENI (0x00040000)
+#define TX_QUEUE_0_CONFIG_ESI (0x00080000)
+#define TX_QUEUE_0_CONFIG_EDI (0x00100000)
+
+#define reg_TX_QUEUE_0_BUF_CONFIG(base) __REG32(base, 0x00000284)
+#define TX_QUEUE_0_BUF_CONFIG_OCN_PORT (0x0000003f)
+#define TX_QUEUE_0_BUF_CONFIG_BURST (0x00000300)
+#define TX_QUEUE_0_BUF_CONFIG_BSWP (0x00000400)
+#define TX_QUEUE_0_BUF_CONFIG_WSWP (0x00000800)
+
+#define OCN_PORT_HLP 0 /* HLP Interface */
+#define OCN_PORT_PCI_X 1 /* PCI-X Interface */
+#define OCN_PORT_PROCESSOR_MASTER 2 /* Processor Interface (master) */
+#define OCN_PORT_PROCESSOR_SLAVE 3 /* Processor Interface (slave) */
+#define OCN_PORT_MEMORY 4 /* Memory Controller */
+#define OCN_PORT_DMA 5 /* DMA Controller */
+#define OCN_PORT_ETHERNET 6 /* Ethernet Controller */
+#define OCN_PORT_PRINT 7 /* Print Engine Interface */
+
+#define reg_TX_QUEUE_0_PTR_LOW(base) __REG32(base, 0x00000288)
+
+#define reg_TX_QUEUE_0_PTR_HIGH(base) __REG32(base, 0x0000028c)
+#define TX_QUEUE_0_PTR_HIGH_VALID (0x80000000)
+
+#define reg_RX_CONFIG(base) __REG32(base, 0x00000320)
+#define RX_CONFIG_DEF_Q (0x00000003)
+#define RX_CONFIG_EMF (0x00000100)
+#define RX_CONFIG_EUF (0x00000200)
+#define RX_CONFIG_BFE (0x00000400)
+#define RX_CONFIG_MFE (0x00000800)
+#define RX_CONFIG_UFE (0x00001000)
+#define RX_CONFIG_SE (0x00002000)
+#define RX_CONFIG_ABF (0x00200000)
+#define RX_CONFIG_APE (0x00400000)
+#define RX_CONFIG_CHP (0x00800000)
+#define RX_CONFIG_RST (0x80000000)
+
+#define reg_RX_CONTROL(base) __REG32(base, 0x00000324)
+#define GE_E0_RX_CONTROL_QUEUE_ENABLES (0x0000000f)
+#define GE_E0_RX_CONTROL_GO (0x00008000)
+#define GE_E0_RX_CONTROL_EAI (0x20000000)
+#define GE_E0_RX_CONTROL_ABT (0x40000000)
+#define GE_E0_RX_CONTROL_EII (0x80000000)
+
+#define reg_RX_EXTENDED_STATUS(base) __REG32(base, 0x0000032c)
+#define RX_EXTENDED_STATUS (0x0000032c)
+#define RX_EXTENDED_STATUS_EOQ (0x0000000f)
+#define RX_EXTENDED_STATUS_EOQ_0 (0x00000001)
+#define RX_EXTENDED_STATUS_EOF (0x00000f00)
+#define RX_EXTENDED_STATUS_DESCRIPTOR_INTERRUPT_CONDITION (0x000f0000)
+#define RX_EXTENDED_STATUS_ERROR_FLAG (0x0f000000)
+
+#define reg_RX_THRESHOLDS(base) __REG32(base, 0x00000330)
+
+#define reg_RX_DIAGNOSTIC_ADDR(base) __REG32(base, 0x00000370)
+#define RX_DIAGNOSTIC_ADDR_INDEX (0x0000007f)
+#define RX_DIAGNOSTIC_ADDR_DFR (0x40000000)
+#define RX_DIAGNOSTIC_ADDR_AI (0x80000000)
+
+#define reg_RX_DIAGNOSTIC_DATA(base) __REG32(base, 0x00000374)
+
+#define reg_RX_QUEUE_0_CONFIG(base) __REG32(base, 0x00000380)
+#define RX_QUEUE_0_CONFIG_OCN_PORT (0x0000003f)
+#define RX_QUEUE_0_CONFIG_BSWP (0x00000400)
+#define RX_QUEUE_0_CONFIG_WSWP (0x00000800)
+#define RX_QUEUE_0_CONFIG_AM (0x00004000)
+#define RX_QUEUE_0_CONFIG_EEI (0x00010000)
+#define RX_QUEUE_0_CONFIG_ELI (0x00020000)
+#define RX_QUEUE_0_CONFIG_ENI (0x00040000)
+#define RX_QUEUE_0_CONFIG_ESI (0x00080000)
+#define RX_QUEUE_0_CONFIG_EDI (0x00100000)
+
+#define reg_RX_QUEUE_0_BUF_CONFIG(base) __REG32(base, 0x00000384)
+#define RX_QUEUE_0_BUF_CONFIG_OCN_PORT (0x0000003f)
+#define RX_QUEUE_0_BUF_CONFIG_BURST (0x00000300)
+#define RX_QUEUE_0_BUF_CONFIG_BSWP (0x00000400)
+#define RX_QUEUE_0_BUF_CONFIG_WSWP (0x00000800)
+
+#define reg_RX_QUEUE_0_PTR_LOW(base) __REG32(base, 0x00000388)
+
+#define reg_RX_QUEUE_0_PTR_HIGH(base) __REG32(base, 0x0000038c)
+#define RX_QUEUE_0_PTR_HIGH_VALID (0x80000000)
+
+/*
+ * PHY register definitions
+ */
+/* the first 15 PHY registers are standard. */
+#define PHY_CTRL_REG 0 /* Control Register */
+#define PHY_STATUS_REG 1 /* Status Regiser */
+#define PHY_ID1_REG 2 /* Phy Id Reg (word 1) */
+#define PHY_ID2_REG 3 /* Phy Id Reg (word 2) */
+#define PHY_AN_ADV_REG 4 /* Autoneg Advertisement */
+#define PHY_LP_ABILITY_REG 5 /* Link Partner Ability (Base Page) */
+#define PHY_AUTONEG_EXP_REG 6 /* Autoneg Expansion Reg */
+#define PHY_NEXT_PAGE_TX_REG 7 /* Next Page TX */
+#define PHY_LP_NEXT_PAGE_REG 8 /* Link Partner Next Page */
+#define PHY_1000T_CTRL_REG 9 /* 1000Base-T Control Reg */
+#define PHY_1000T_STATUS_REG 10 /* 1000Base-T Status Reg */
+#define PHY_EXT_STATUS_REG 11 /* Extended Status Reg */
+
+/*
+ * PHY Register bit masks.
+ */
+#define PHY_CTRL_RESET (1 << 15)
+#define PHY_CTRL_LOOPBACK (1 << 14)
+#define PHY_CTRL_SPEED0 (1 << 13)
+#define PHY_CTRL_AN_EN (1 << 12)
+#define PHY_CTRL_PWR_DN (1 << 11)
+#define PHY_CTRL_ISOLATE (1 << 10)
+#define PHY_CTRL_RESTART_AN (1 << 9)
+#define PHY_CTRL_FULL_DUPLEX (1 << 8)
+#define PHY_CTRL_CT_EN (1 << 7)
+#define PHY_CTRL_SPEED1 (1 << 6)
+
+#define PHY_STAT_100BASE_T4 (1 << 15)
+#define PHY_STAT_100BASE_X_FD (1 << 14)
+#define PHY_STAT_100BASE_X_HD (1 << 13)
+#define PHY_STAT_10BASE_T_FD (1 << 12)
+#define PHY_STAT_10BASE_T_HD (1 << 11)
+#define PHY_STAT_100BASE_T2_FD (1 << 10)
+#define PHY_STAT_100BASE_T2_HD (1 << 9)
+#define PHY_STAT_EXT_STAT (1 << 8)
+#define PHY_STAT_RESERVED (1 << 7)
+#define PHY_STAT_MFPS (1 << 6) /* Management Frames Preamble Suppression */
+#define PHY_STAT_AN_COMPLETE (1 << 5)
+#define PHY_STAT_REM_FAULT (1 << 4)
+#define PHY_STAT_AN_CAP (1 << 3)
+#define PHY_STAT_LINK_UP (1 << 2)
+#define PHY_STAT_JABBER (1 << 1)
+#define PHY_STAT_EXT_CAP (1 << 0)
+
+#define TBI_CONTROL_2 0x11
+#define TBI_CONTROL_2_ENABLE_COMMA_DETECT 0x0001
+#define TBI_CONTROL_2_ENABLE_WRAP 0x0002
+#define TBI_CONTROL_2_G_MII_MODE 0x0010
+#define TBI_CONTROL_2_RECEIVE_CLOCK_SELECT 0x0020
+#define TBI_CONTROL_2_AUTO_NEGOTIATION_SENSE 0x0100
+#define TBI_CONTROL_2_DISABLE_TRANSMIT_RUNNING_DISPARITY 0x1000
+#define TBI_CONTROL_2_DISABLE_RECEIVE_RUNNING_DISPARITY 0x2000
+#define TBI_CONTROL_2_SHORTCUT_LINK_TIMER 0x4000
+#define TBI_CONTROL_2_SOFT_RESET 0x8000
+
+/* marvel specific */
+#define MV1111_EXT_CTRL1_REG 16 /* PHY Specific Control Reg */
+#define MV1111_SPEC_STAT_REG 17 /* PHY Specific Status Reg */
+#define MV1111_EXT_CTRL2_REG 20 /* Extended PHY Specific Control Reg */
+
+/*
+ * MARVELL 88E1111 PHY register bit masks
+ */
+/* PHY Specific Status Register (MV1111_EXT_CTRL1_REG) */
+
+#define SPEC_STAT_SPEED_MASK (3 << 14)
+#define SPEC_STAT_FULL_DUP (1 << 13)
+#define SPEC_STAT_PAGE_RCVD (1 << 12)
+#define SPEC_STAT_RESOLVED (1 << 11) /* Speed and Duplex Resolved */
+#define SPEC_STAT_LINK_UP (1 << 10)
+#define SPEC_STAT_CABLE_LEN_MASK (7 << 7)/* Cable Length (100/1000 modes only) */
+#define SPEC_STAT_MDIX (1 << 6)
+#define SPEC_STAT_POLARITY (1 << 1)
+#define SPEC_STAT_JABBER (1 << 0)
+
+#define SPEED_1000 (2 << 14)
+#define SPEED_100 (1 << 14)
+#define SPEED_10 (0 << 14)
+
+#define TBI_ADDR 0x1E /* Ten Bit Interface address */
+
+/* negotiated link parameters */
+#define LINK_SPEED_UNKNOWN 0
+#define LINK_SPEED_10 1
+#define LINK_SPEED_100 2
+#define LINK_SPEED_1000 3
+
+#define LINK_DUPLEX_UNKNOWN 0
+#define LINK_DUPLEX_HALF 1
+#define LINK_DUPLEX_FULL 2
+
+static unsigned int phy_address[] = { 8, 9 };
+
+#define vuint32 volatile u32
+
+/* TX/RX buffer descriptors. MUST be cache line aligned in memory. (32 byte)
+ * This structure is accessed by the ethernet DMA engine which means it
+ * MUST be in LITTLE ENDIAN format */
+struct dma_descriptor {
+ vuint32 start_addr0; /* buffer address, least significant bytes. */
+ vuint32 start_addr1; /* buffer address, most significant bytes. */
+ vuint32 next_descr_addr0;/* next descriptor address, least significant bytes. Must be 64-bit aligned. */
+ vuint32 next_descr_addr1;/* next descriptor address, most significant bytes. */
+ vuint32 vlan_byte_count;/* VLAN tag(top 2 bytes) and byte countt (bottom 2 bytes). */
+ vuint32 config_status; /* Configuration/Status. */
+ vuint32 reserved1; /* reserved to make the descriptor cache line aligned. */
+ vuint32 reserved2; /* reserved to make the descriptor cache line aligned. */
+};
+
+/* last next descriptor address flag */
+#define DMA_DESCR_LAST (1 << 31)
+
+/* TX DMA descriptor config status bits */
+#define DMA_DESCR_TX_EOF (1 << 0) /* end of frame */
+#define DMA_DESCR_TX_SOF (1 << 1) /* start of frame */
+#define DMA_DESCR_TX_PFVLAN (1 << 2)
+#define DMA_DESCR_TX_HUGE (1 << 3)
+#define DMA_DESCR_TX_PAD (1 << 4)
+#define DMA_DESCR_TX_CRC (1 << 5)
+#define DMA_DESCR_TX_DESCR_INT (1 << 14)
+#define DMA_DESCR_TX_RETRY_COUNT 0x000F0000
+#define DMA_DESCR_TX_ONE_COLLISION (1 << 20)
+#define DMA_DESCR_TX_LATE_COLLISION (1 << 24)
+#define DMA_DESCR_TX_UNDERRUN (1 << 25)
+#define DMA_DESCR_TX_RETRY_LIMIT (1 << 26)
+#define DMA_DESCR_TX_OK (1 << 30)
+#define DMA_DESCR_TX_OWNER (1 << 31)
+
+/* RX DMA descriptor status bits */
+#define DMA_DESCR_RX_EOF (1 << 0)
+#define DMA_DESCR_RX_SOF (1 << 1)
+#define DMA_DESCR_RX_VTF (1 << 2)
+#define DMA_DESCR_RX_FRAME_IS_TYPE (1 << 3)
+#define DMA_DESCR_RX_SHORT_FRAME (1 << 4)
+#define DMA_DESCR_RX_HASH_MATCH (1 << 7)
+#define DMA_DESCR_RX_BAD_FRAME (1 << 8)
+#define DMA_DESCR_RX_OVERRUN (1 << 9)
+#define DMA_DESCR_RX_MAX_FRAME_LEN (1 << 11)
+#define DMA_DESCR_RX_CRC_ERROR (1 << 12)
+#define DMA_DESCR_RX_DESCR_INT (1 << 13)
+#define DMA_DESCR_RX_OWNER (1 << 15)
+
+#define RX_BUFFER_SIZE PKTSIZE
+#define NUM_RX_DESC PKTBUFSRX
+
+static struct dma_descriptor tx_descriptor __attribute__ ((aligned(32)));
+
+static struct dma_descriptor rx_descr_array[NUM_RX_DESC]
+ __attribute__ ((aligned(32)));
+
+static struct dma_descriptor *rx_descr_current;
+
+static int tsi108_eth_probe (struct eth_device *dev, bd_t * bis);
+static int tsi108_eth_send (struct eth_device *dev,
+ volatile void *packet, int length);
+static int tsi108_eth_recv (struct eth_device *dev);
+static void tsi108_eth_halt (struct eth_device *dev);
+static unsigned int read_phy (unsigned int base,
+ unsigned int phy_addr, unsigned int phy_reg);
+static void write_phy (unsigned int base,
+ unsigned int phy_addr,
+ unsigned int phy_reg, unsigned int phy_data);
+
+#if TSI108_ETH_DEBUG > 100
+/*
+ * print phy debug infomation
+ */
+static void dump_phy_regs (unsigned int phy_addr)
+{
+ int i;
+
+ printf ("PHY %d registers\n", phy_addr);
+ for (i = 0; i <= 30; i++) {
+ printf ("%2d 0x%04x\n", i, read_phy (ETH_BASE, phy_addr, i));
+ }
+ printf ("\n");
+
+}
+#else
+#define dump_phy_regs(base) do{}while(0)
+#endif
+
+#if TSI108_ETH_DEBUG > 100
+/*
+ * print debug infomation
+ */
+static void tx_diag_regs (unsigned int base)
+{
+ int i;
+ unsigned long dummy;
+
+ printf ("TX diagnostics registers\n");
+ reg_TX_DIAGNOSTIC_ADDR(base) = 0x00 | TX_DIAGNOSTIC_ADDR_AI;
+ udelay (1000);
+ dummy = reg_TX_DIAGNOSTIC_DATA(base);
+ for (i = 0x00; i <= 0x05; i++) {
+ udelay (1000);
+ printf ("0x%02x 0x%08x\n", i, reg_TX_DIAGNOSTIC_DATA(base));
+ }
+ reg_TX_DIAGNOSTIC_ADDR(base) = 0x40 | TX_DIAGNOSTIC_ADDR_AI;
+ udelay (1000);
+ dummy = reg_TX_DIAGNOSTIC_DATA(base);
+ for (i = 0x40; i <= 0x47; i++) {
+ udelay (1000);
+ printf ("0x%02x 0x%08x\n", i, reg_TX_DIAGNOSTIC_DATA(base));
+ }
+ printf ("\n");
+
+}
+#else
+#define tx_diag_regs(base) do{}while(0)
+#endif
+
+#if TSI108_ETH_DEBUG > 100
+/*
+ * print debug infomation
+ */
+static void rx_diag_regs (unsigned int base)
+{
+ int i;
+ unsigned long dummy;
+
+ printf ("RX diagnostics registers\n");
+ reg_RX_DIAGNOSTIC_ADDR(base) = 0x00 | RX_DIAGNOSTIC_ADDR_AI;
+ udelay (1000);
+ dummy = reg_RX_DIAGNOSTIC_DATA(base);
+ for (i = 0x00; i <= 0x05; i++) {
+ udelay (1000);
+ printf ("0x%02x 0x%08x\n", i, reg_RX_DIAGNOSTIC_DATA(base));
+ }
+ reg_RX_DIAGNOSTIC_ADDR(base) = 0x40 | RX_DIAGNOSTIC_ADDR_AI;
+ udelay (1000);
+ dummy = reg_RX_DIAGNOSTIC_DATA(base);
+ for (i = 0x08; i <= 0x0a; i++) {
+ udelay (1000);
+ printf ("0x%02x 0x%08x\n", i, reg_RX_DIAGNOSTIC_DATA(base));
+ }
+ printf ("\n");
+
+}
+#else
+#define rx_diag_regs(base) do{}while(0)
+#endif
+
+#if TSI108_ETH_DEBUG > 100
+/*
+ * print debug infomation
+ */
+static void debug_mii_regs (unsigned int base)
+{
+ printf ("MII_MGMT_CONFIG 0x%08x\n", reg_MII_MGMT_CONFIG(base));
+ printf ("MII_MGMT_COMMAND 0x%08x\n", reg_MII_MGMT_COMMAND(base));
+ printf ("MII_MGMT_ADDRESS 0x%08x\n", reg_MII_MGMT_ADDRESS(base));
+ printf ("MII_MGMT_CONTROL 0x%08x\n", reg_MII_MGMT_CONTROL(base));
+ printf ("MII_MGMT_STATUS 0x%08x\n", reg_MII_MGMT_STATUS(base));
+ printf ("MII_MGMT_INDICATORS 0x%08x\n", reg_MII_MGMT_INDICATORS(base));
+ printf ("\n");
+
+}
+#else
+#define debug_mii_regs(base) do{}while(0)
+#endif
+
+/*
+ * Wait until the phy bus is non-busy
+ */
+static void phy_wait (unsigned int base, unsigned int condition)
+{
+ int timeout;
+
+ timeout = 0;
+ while (reg_MII_MGMT_INDICATORS(base) & condition) {
+ udelay (10);
+ if (++timeout > 10000) {
+ printf ("ERROR: timeout waiting for phy bus (%d)\n",
+ condition);
+ break;
+ }
+ }
+}
+
+/*
+ * read phy register
+ */
+static unsigned int read_phy (unsigned int base,
+ unsigned int phy_addr, unsigned int phy_reg)
+{
+ unsigned int value;
+
+ phy_wait (base, MII_MGMT_INDICATORS_BUSY);
+
+ reg_MII_MGMT_ADDRESS(base) = (phy_addr << 8) | phy_reg;
+
+ /* Ensure that the Read Cycle bit is cleared prior to next read cycle */
+ reg_MII_MGMT_COMMAND(base) = 0;
+
+ /* start the read */
+ reg_MII_MGMT_COMMAND(base) = MII_MGMT_COMMAND_READ_CYCLE;
+
+ /* wait for the read to complete */
+ phy_wait (base,
+ MII_MGMT_INDICATORS_NOT_VALID | MII_MGMT_INDICATORS_BUSY);
+
+ value = reg_MII_MGMT_STATUS(base);
+
+ reg_MII_MGMT_COMMAND(base) = 0;
+
+ return value;
+}
+
+/*
+ * write phy register
+ */
+static void write_phy (unsigned int base,
+ unsigned int phy_addr,
+ unsigned int phy_reg, unsigned int phy_data)
+{
+ phy_wait (base, MII_MGMT_INDICATORS_BUSY);
+
+ reg_MII_MGMT_ADDRESS(base) = (phy_addr << 8) | phy_reg;
+
+ /* Ensure that the Read Cycle bit is cleared prior to next cycle */
+ reg_MII_MGMT_COMMAND(base) = 0;
+
+ /* start the write */
+ reg_MII_MGMT_CONTROL(base) = phy_data;
+}
+
+/*
+ * configure the marvell 88e1111 phy
+ */
+static int marvell_88e_phy_config (struct eth_device *dev, int *speed,
+ int *duplex)
+{
+ unsigned long base;
+ unsigned long phy_addr;
+ unsigned int phy_status;
+ unsigned int phy_spec_status;
+ int timeout;
+ int phy_speed;
+ int phy_duplex;
+ unsigned int value;
+
+ phy_speed = LINK_SPEED_UNKNOWN;
+ phy_duplex = LINK_DUPLEX_UNKNOWN;
+
+ base = dev->iobase;
+ phy_addr = (unsigned long)dev->priv;
+
+ /* Take the PHY out of reset. */
+ write_phy (ETH_BASE, phy_addr, PHY_CTRL_REG, PHY_CTRL_RESET);
+
+ /* Wait for the reset process to complete. */
+ udelay (10);
+ timeout = 0;
+ while ((phy_status =
+ read_phy (ETH_BASE, phy_addr, PHY_CTRL_REG)) & PHY_CTRL_RESET) {
+ udelay (10);
+ if (++timeout > 10000) {
+ printf ("ERROR: timeout waiting for phy reset\n");
+ break;
+ }
+ }
+
+ /* TBI Configuration. */
+ write_phy (base, TBI_ADDR, TBI_CONTROL_2, TBI_CONTROL_2_G_MII_MODE |
+ TBI_CONTROL_2_RECEIVE_CLOCK_SELECT);
+ /* Wait for the link to be established. */
+ timeout = 0;
+ do {
+ udelay (20000);
+ phy_status = read_phy (ETH_BASE, phy_addr, PHY_STATUS_REG);
+ if (++timeout > 100) {
+ debug_lev(1, "ERROR: unable to establish link!!!\n");
+ break;
+ }
+ } while ((phy_status & PHY_STAT_LINK_UP) == 0);
+
+ if ((phy_status & PHY_STAT_LINK_UP) == 0)
+ return 0;
+
+ value = 0;
+ phy_spec_status = read_phy (ETH_BASE, phy_addr, MV1111_SPEC_STAT_REG);
+ if (phy_spec_status & SPEC_STAT_RESOLVED) {
+ switch (phy_spec_status & SPEC_STAT_SPEED_MASK) {
+ case SPEED_1000:
+ phy_speed = LINK_SPEED_1000;
+ value |= PHY_CTRL_SPEED1;
+ break;
+ case SPEED_100:
+ phy_speed = LINK_SPEED_100;
+ value |= PHY_CTRL_SPEED0;
+ break;
+ case SPEED_10:
+ phy_speed = LINK_SPEED_10;
+ break;
+ }
+ if (phy_spec_status & SPEC_STAT_FULL_DUP) {
+ phy_duplex = LINK_DUPLEX_FULL;
+ value |= PHY_CTRL_FULL_DUPLEX;
+ } else
+ phy_duplex = LINK_DUPLEX_HALF;
+ }
+ /* set TBI speed */
+ write_phy (base, TBI_ADDR, PHY_CTRL_REG, value);
+ write_phy (base, TBI_ADDR, PHY_AN_ADV_REG, 0x0060);
+
+#if TSI108_ETH_DEBUG > 0
+ printf ("%s link is up", dev->name);
+ phy_spec_status = read_phy (ETH_BASE, phy_addr, MV1111_SPEC_STAT_REG);
+ if (phy_spec_status & SPEC_STAT_RESOLVED) {
+ switch (phy_speed) {
+ case LINK_SPEED_1000:
+ printf (", 1000 Mbps");
+ break;
+ case LINK_SPEED_100:
+ printf (", 100 Mbps");
+ break;
+ case LINK_SPEED_10:
+ printf (", 10 Mbps");
+ break;
+ }
+ if (phy_duplex == LINK_DUPLEX_FULL)
+ printf (", Full duplex");
+ else
+ printf (", Half duplex");
+ }
+ printf ("\n");
+#endif
+
+ dump_phy_regs (TBI_ADDR);
+ if (speed)
+ *speed = phy_speed;
+ if (duplex)
+ *duplex = phy_duplex;
+
+ return 1;
+}
+
+/*
+ * External interface
+ *
+ * register the tsi108 ethernet controllers with the multi-ethernet system
+ */
+int tsi108_eth_initialize (bd_t * bis)
+{
+ struct eth_device *dev;
+ int index;
+
+ for (index = 0; index < CONFIG_TSI108_ETH_NUM_PORTS; index++) {
+ dev = (struct eth_device *)malloc(sizeof(struct eth_device));
+
+ sprintf (dev->name, "TSI108_eth%d", index);
+
+ dev->iobase = ETH_BASE + (index * ETH_PORT_OFFSET);
+ dev->priv = (void *)(phy_address[index]);
+ dev->init = tsi108_eth_probe;
+ dev->halt = tsi108_eth_halt;
+ dev->send = tsi108_eth_send;
+ dev->recv = tsi108_eth_recv;
+
+ eth_register(dev);
+ }
+ return index;
+}
+
+/*
+ * probe for and initialize a single ethernet interface
+ */
+static int tsi108_eth_probe (struct eth_device *dev, bd_t * bis)
+{
+ unsigned long base;
+ unsigned long value;
+ int index;
+ struct dma_descriptor *tx_descr;
+ struct dma_descriptor *rx_descr;
+ int speed;
+ int duplex;
+
+ base = dev->iobase;
+
+ reg_PORT_CONTROL(base) = PORT_CONTROL_STE | PORT_CONTROL_BPT;
+
+ /* Bring DMA/FIFO out of reset. */
+ reg_TX_CONFIG(base) = 0x00000000;
+ reg_RX_CONFIG(base) = 0x00000000;
+
+ reg_TX_THRESHOLDS(base) = (192 << 16) | 192;
+ reg_RX_THRESHOLDS(base) = (192 << 16) | 112;
+
+ /* Bring MAC out of reset. */
+ reg_MAC_CONFIG_1(base) = 0x00000000;
+
+ /* DMA MAC configuration. */
+ reg_MAC_CONFIG_1(base) =
+ MAC_CONFIG_1_RX_ENABLE | MAC_CONFIG_1_TX_ENABLE;
+
+ reg_MII_MGMT_CONFIG(base) = MII_MGMT_CONFIG_NO_PREAMBLE;
+ reg_MAXIMUM_FRAME_LENGTH(base) = RX_BUFFER_SIZE;
+
+ /* Note: Early tsi108 manual did not have correct byte order
+ * for the station address.*/
+ reg_STATION_ADDRESS_1(base) = (dev->enetaddr[5] << 24) |
+ (dev->enetaddr[4] << 16) |
+ (dev->enetaddr[3] << 8) | (dev->enetaddr[2] << 0);
+
+ reg_STATION_ADDRESS_2(base) = (dev->enetaddr[1] << 24) |
+ (dev->enetaddr[0] << 16);
+
+ if (marvell_88e_phy_config(dev, &speed, &duplex) == 0)
+ return 0;
+
+ value =
+ MAC_CONFIG_2_PREAMBLE_LENGTH(7) | MAC_CONFIG_2_PAD_CRC |
+ MAC_CONFIG_2_CRC_ENABLE;
+ if (speed == LINK_SPEED_1000)
+ value |= MAC_CONFIG_2_INTERFACE_MODE(INTERFACE_MODE_BYTE);
+ else {
+ value |= MAC_CONFIG_2_INTERFACE_MODE(INTERFACE_MODE_NIBBLE);
+ reg_PORT_CONTROL(base) |= PORT_CONTROL_SPD;
+ }
+ if (duplex == LINK_DUPLEX_FULL) {
+ value |= MAC_CONFIG_2_FULL_DUPLEX;
+ reg_PORT_CONTROL(base) &= ~PORT_CONTROL_BPT;
+ } else
+ reg_PORT_CONTROL(base) |= PORT_CONTROL_BPT;
+ reg_MAC_CONFIG_2(base) = value;
+
+ reg_RX_CONFIG(base) = RX_CONFIG_SE;
+ reg_RX_QUEUE_0_CONFIG(base) = OCN_PORT_MEMORY;
+ reg_RX_QUEUE_0_BUF_CONFIG(base) = OCN_PORT_MEMORY;
+
+ /* initialize the RX DMA descriptors */
+ rx_descr = &rx_descr_array[0];
+ rx_descr_current = rx_descr;
+ for (index = 0; index < NUM_RX_DESC; index++) {
+ /* make sure the receive buffers are not in cache */
+ invalidate_dcache_range((unsigned long)NetRxPackets[index],
+ (unsigned long)NetRxPackets[index] +
+ RX_BUFFER_SIZE);
+ rx_descr->start_addr0 =
+ cpu_to_le32((vuint32) NetRxPackets[index]);
+ rx_descr->start_addr1 = 0;
+ rx_descr->next_descr_addr0 =
+ cpu_to_le32((vuint32) (rx_descr + 1));
+ rx_descr->next_descr_addr1 = 0;
+ rx_descr->vlan_byte_count = 0;
+ rx_descr->config_status = cpu_to_le32((RX_BUFFER_SIZE << 16) |
+ DMA_DESCR_RX_OWNER);
+ rx_descr++;
+ }
+ rx_descr--;
+ rx_descr->next_descr_addr0 = 0;
+ rx_descr->next_descr_addr1 = cpu_to_le32(DMA_DESCR_LAST);
+ /* Push the descriptors to RAM so the ethernet DMA can see them */
+ invalidate_dcache_range((unsigned long)rx_descr_array,
+ (unsigned long)rx_descr_array +
+ sizeof(rx_descr_array));
+
+ /* enable RX queue */
+ reg_RX_CONTROL(base) = TX_CONTROL_GO | 0x01;
+ reg_RX_QUEUE_0_PTR_LOW(base) = (u32) rx_descr_current;
+ /* enable receive DMA */
+ reg_RX_QUEUE_0_PTR_HIGH(base) = RX_QUEUE_0_PTR_HIGH_VALID;
+
+ reg_TX_QUEUE_0_CONFIG(base) = OCN_PORT_MEMORY;
+ reg_TX_QUEUE_0_BUF_CONFIG(base) = OCN_PORT_MEMORY;
+
+ /* initialize the TX DMA descriptor */
+ tx_descr = &tx_descriptor;
+
+ tx_descr->start_addr0 = 0;
+ tx_descr->start_addr1 = 0;
+ tx_descr->next_descr_addr0 = 0;
+ tx_descr->next_descr_addr1 = cpu_to_le32(DMA_DESCR_LAST);
+ tx_descr->vlan_byte_count = 0;
+ tx_descr->config_status = cpu_to_le32(DMA_DESCR_TX_OK |
+ DMA_DESCR_TX_SOF |
+ DMA_DESCR_TX_EOF);
+ /* enable TX queue */
+ reg_TX_CONTROL(base) = TX_CONTROL_GO | 0x01;
+
+ return 1;
+}
+
+/*
+ * send a packet
+ */
+static int tsi108_eth_send (struct eth_device *dev,
+ volatile void *packet, int length)
+{
+ unsigned long base;
+ int timeout;
+ struct dma_descriptor *tx_descr;
+ unsigned long status;
+
+ base = dev->iobase;
+ tx_descr = &tx_descriptor;
+
+ /* Wait until the last packet has been transmitted. */
+ timeout = 0;
+ do {
+ /* make sure we see the changes made by the DMA engine */
+ invalidate_dcache_range((unsigned long)tx_descr,
+ (unsigned long)tx_descr +
+ sizeof(struct dma_descriptor));
+
+ if (timeout != 0)
+ udelay (15);
+ if (++timeout > 10000) {
+ tx_diag_regs(base);
+ debug_lev(1,
+ "ERROR: timeout waiting for last transmit packet to be sent\n");
+ return 0;
+ }
+ } while (tx_descr->config_status & cpu_to_le32(DMA_DESCR_TX_OWNER));
+
+ status = le32_to_cpu(tx_descr->config_status);
+ if ((status & DMA_DESCR_TX_OK) == 0) {
+#ifdef TX_PRINT_ERRORS
+ printf ("TX packet error: 0x%08x\n %s%s%s%s\n", status,
+ status & DMA_DESCR_TX_OK ? "tx error, " : "",
+ status & DMA_DESCR_TX_RETRY_LIMIT ?
+ "retry limit reached, " : "",
+ status & DMA_DESCR_TX_UNDERRUN ? "underrun, " : "",
+ status & DMA_DESCR_TX_LATE_COLLISION ? "late collision, "
+ : "");
+#endif
+ }
+
+ debug_lev (9, "sending packet %d\n", length);
+ tx_descr->start_addr0 = cpu_to_le32((vuint32) packet);
+ tx_descr->start_addr1 = 0;
+ tx_descr->next_descr_addr0 = 0;
+ tx_descr->next_descr_addr1 = cpu_to_le32(DMA_DESCR_LAST);
+ tx_descr->vlan_byte_count = cpu_to_le32(length);
+ tx_descr->config_status = cpu_to_le32(DMA_DESCR_TX_OWNER |
+ DMA_DESCR_TX_CRC |
+ DMA_DESCR_TX_PAD |
+ DMA_DESCR_TX_SOF |
+ DMA_DESCR_TX_EOF);
+
+ invalidate_dcache_range((unsigned long)tx_descr,
+ (unsigned long)tx_descr +
+ sizeof(struct dma_descriptor));
+
+ invalidate_dcache_range((unsigned long)packet,
+ (unsigned long)packet + length);
+
+ reg_TX_QUEUE_0_PTR_LOW(base) = (u32) tx_descr;
+ reg_TX_QUEUE_0_PTR_HIGH(base) = TX_QUEUE_0_PTR_HIGH_VALID;
+
+ return length;
+}
+
+/*
+ * Check for received packets and send them up the protocal stack
+ */
+static int tsi108_eth_recv (struct eth_device *dev)
+{
+ struct dma_descriptor *rx_descr;
+ unsigned long base;
+ int length = 0;
+ unsigned long status;
+ volatile uchar *buffer;
+
+ base = dev->iobase;
+
+ /* make sure we see the changes made by the DMA engine */
+ invalidate_dcache_range ((unsigned long)rx_descr_array,
+ (unsigned long)rx_descr_array +
+ sizeof(rx_descr_array));
+
+ /* process all of the received packets */
+ rx_descr = rx_descr_current;
+ while ((rx_descr->config_status & cpu_to_le32(DMA_DESCR_RX_OWNER)) == 0) {
+ /* check for error */
+ status = le32_to_cpu(rx_descr->config_status);
+ if (status & DMA_DESCR_RX_BAD_FRAME) {
+#ifdef RX_PRINT_ERRORS
+ printf ("RX packet error: 0x%08x\n %s%s%s%s%s%s\n",
+ status,
+ status & DMA_DESCR_RX_FRAME_IS_TYPE ? "too big, "
+ : "",
+ status & DMA_DESCR_RX_SHORT_FRAME ? "too short, "
+ : "",
+ status & DMA_DESCR_RX_BAD_FRAME ? "bad frame, " :
+ "",
+ status & DMA_DESCR_RX_OVERRUN ? "overrun, " : "",
+ status & DMA_DESCR_RX_MAX_FRAME_LEN ?
+ "max length, " : "",
+ status & DMA_DESCR_RX_CRC_ERROR ? "CRC error, " :
+ "");
+#endif
+ } else {
+ length =
+ le32_to_cpu(rx_descr->vlan_byte_count) & 0xFFFF;
+
+ /*** process packet ***/
+ buffer =
+ (volatile uchar
+ *)(le32_to_cpu (rx_descr->start_addr0));
+ NetReceive (buffer, length);
+
+ invalidate_dcache_range ((unsigned long)buffer,
+ (unsigned long)buffer +
+ RX_BUFFER_SIZE);
+ }
+ /* Give this buffer back to the DMA engine */
+ rx_descr->vlan_byte_count = 0;
+ rx_descr->config_status = cpu_to_le32 ((RX_BUFFER_SIZE << 16) |
+ DMA_DESCR_RX_OWNER);
+ /* move descriptor pointer forward */
+ rx_descr =
+ (struct dma_descriptor
+ *)(le32_to_cpu (rx_descr->next_descr_addr0));
+ if (rx_descr == 0)
+ rx_descr = &rx_descr_array[0];
+ }
+ /* remember where we are for next time */
+ rx_descr_current = rx_descr;
+
+ /* If the DMA engine has reached the end of the queue
+ * start over at the begining */
+ if (reg_RX_EXTENDED_STATUS(base) & RX_EXTENDED_STATUS_EOQ_0) {
+
+ reg_RX_EXTENDED_STATUS(base) = RX_EXTENDED_STATUS_EOQ_0;
+ reg_RX_QUEUE_0_PTR_LOW(base) = (u32) & rx_descr_array[0];
+ reg_RX_QUEUE_0_PTR_HIGH(base) = RX_QUEUE_0_PTR_HIGH_VALID;
+ }
+
+ return length;
+}
+
+/*
+ * disable an ethernet interface
+ */
+static void tsi108_eth_halt (struct eth_device *dev)
+{
+ unsigned long base;
+
+ base = dev->iobase;
+
+ /* Put DMA/FIFO into reset state. */
+ reg_TX_CONFIG(base) = TX_CONFIG_RST;
+ reg_RX_CONFIG(base) = RX_CONFIG_RST;
+
+ /* Put MAC into reset state. */
+ reg_MAC_CONFIG_1(base) = MAC_CONFIG_1_SOFT_RESET;
+}
+
+#endif
diff --git a/drivers/tsi108_i2c.c b/drivers/tsi108_i2c.c
new file mode 100644
index 0000000..eb52cb6
--- /dev/null
+++ b/drivers/tsi108_i2c.c
@@ -0,0 +1,283 @@
+/*
+ * (C) Copyright 2004 Tundra Semiconductor Corp.
+ * Author: Alex Bounine
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <config.h>
+#include <common.h>
+
+#ifdef CONFIG_TSI108_I2C
+#include <tsi108.h>
+
+#if (CONFIG_COMMANDS & CFG_CMD_I2C)
+
+#define I2C_DELAY 100000
+#undef DEBUG_I2C
+
+#ifdef DEBUG_I2C
+#define DPRINT(x) printf (x)
+#else
+#define DPRINT(x)
+#endif
+
+/* All functions assume that Tsi108 I2C block is the only master on the bus */
+/* I2C read helper function */
+
+static int i2c_read_byte (
+ uint i2c_chan, /* I2C channel number: 0 - main, 1 - SDC SPD */
+ uchar chip_addr,/* I2C device address on the bus */
+ uint byte_addr, /* Byte address within I2C device */
+ uchar * buffer /* pointer to data buffer */
+ )
+{
+ u32 temp;
+ u32 to_count = I2C_DELAY;
+ u32 op_status = TSI108_I2C_TIMEOUT_ERR;
+ u32 chan_offset = TSI108_I2C_OFFSET;
+
+ DPRINT (("I2C read_byte() %d 0x%02x 0x%02x\n",
+ i2c_chan, chip_addr, byte_addr));
+
+ if (0 != i2c_chan)
+ chan_offset = TSI108_I2C_SDRAM_OFFSET;
+
+ /* Check if I2C operation is in progress */
+ temp = *(u32 *) (CFG_TSI108_CSR_BASE + chan_offset + I2C_CNTRL2);
+
+ if (0 == (temp & (I2C_CNTRL2_RD_STATUS | I2C_CNTRL2_WR_STATUS |
+ I2C_CNTRL2_START))) {
+ /* Set device address and operation (read = 0) */
+ temp = (byte_addr << 16) | ((chip_addr & 0x07) << 8) |
+ ((chip_addr >> 3) & 0x0F);
+ *(u32 *) (CFG_TSI108_CSR_BASE + chan_offset + I2C_CNTRL1) =
+ temp;
+
+ /* Issue the read command
+ * (at this moment all other parameters are 0
+ * (size = 1 byte, lane = 0)
+ */
+
+ *(u32 *) (CFG_TSI108_CSR_BASE + chan_offset + I2C_CNTRL2) =
+ (I2C_CNTRL2_START);
+
+ /* Wait until operation completed */
+ do {
+ /* Read I2C operation status */
+ temp = *(u32 *) (CFG_TSI108_CSR_BASE + chan_offset + I2C_CNTRL2);
+
+ if (0 == (temp & (I2C_CNTRL2_RD_STATUS | I2C_CNTRL2_START))) {
+ if (0 == (temp &
+ (I2C_CNTRL2_I2C_CFGERR |
+ I2C_CNTRL2_I2C_TO_ERR))
+ ) {
+ op_status = TSI108_I2C_SUCCESS;
+
+ temp = *(u32 *) (CFG_TSI108_CSR_BASE +
+ chan_offset +
+ I2C_RD_DATA);
+
+ *buffer = (u8) (temp & 0xFF);
+ } else {
+ /* report HW error */
+ op_status = TSI108_I2C_IF_ERROR;
+
+ DPRINT (("I2C HW error reported: 0x%02x\n", temp));
+ }
+
+ break;
+ }
+ } while (to_count--);
+ } else {
+ op_status = TSI108_I2C_IF_BUSY;
+
+ DPRINT (("I2C Transaction start failed: 0x%02x\n", temp));
+ }
+
+ DPRINT (("I2C read_byte() status: 0x%02x\n", op_status));
+ return op_status;
+}
+
+/*
+ * I2C Read interface as defined in "include/i2c.h" :
+ * chip_addr: I2C chip address, range 0..127
+ * (to read from SPD channel EEPROM use (0xD0 ... 0xD7)
+ * NOTE: The bit 7 in the chip_addr serves as a channel select.
+ * This hack is for enabling "isdram" command on Tsi108 boards
+ * without changes to common code. Used for I2C reads only.
+ * byte_addr: Memory or register address within the chip
+ * alen: Number of bytes to use for addr (typically 1, 2 for larger
+ * memories, 0 for register type devices with only one
+ * register)
+ * buffer: Pointer to destination buffer for data to be read
+ * len: How many bytes to read
+ *
+ * Returns: 0 on success, not 0 on failure
+ */
+
+int i2c_read (uchar chip_addr, uint byte_addr, int alen,
+ uchar * buffer, int len)
+{
+ u32 op_status = TSI108_I2C_PARAM_ERR;
+ u32 i2c_if = 0;
+
+ /* Hack to support second (SPD) I2C controller (SPD EEPROM read only).*/
+ if (0xD0 == (chip_addr & ~0x07)) {
+ i2c_if = 1;
+ chip_addr &= 0x7F;
+ }
+ /* Check for valid I2C address */
+ if (chip_addr <= 0x7F && (byte_addr + len) <= (0x01 << (alen * 8))) {
+ while (len--) {
+ op_status = i2c_read_byte(i2c_if, chip_addr, byte_addr++, buffer++);
+
+ if (TSI108_I2C_SUCCESS != op_status) {
+ DPRINT (("I2C read_byte() failed: 0x%02x (%d left)\n", op_status, len));
+
+ break;
+ }
+ }
+ }
+
+ DPRINT (("I2C read() status: 0x%02x\n", op_status));
+ return op_status;
+}
+
+/* I2C write helper function */
+
+static int i2c_write_byte (uchar chip_addr,/* I2C device address on the bus */
+ uint byte_addr, /* Byte address within I2C device */
+ uchar * buffer /* pointer to data buffer */
+ )
+{
+ u32 temp;
+ u32 to_count = I2C_DELAY;
+ u32 op_status = TSI108_I2C_TIMEOUT_ERR;
+
+ /* Check if I2C operation is in progress */
+ temp = *(u32 *) (CFG_TSI108_CSR_BASE + TSI108_I2C_OFFSET + I2C_CNTRL2);
+
+ if (0 == (temp & (I2C_CNTRL2_RD_STATUS | I2C_CNTRL2_WR_STATUS | I2C_CNTRL2_START))) {
+ /* Place data into the I2C Tx Register */
+ *(u32 *) (CFG_TSI108_CSR_BASE + TSI108_I2C_OFFSET +
+ I2C_TX_DATA) = (u32) * buffer;
+
+ /* Set device address and operation */
+ temp =
+ I2C_CNTRL1_I2CWRITE | (byte_addr << 16) |
+ ((chip_addr & 0x07) << 8) | ((chip_addr >> 3) & 0x0F);
+ *(u32 *) (CFG_TSI108_CSR_BASE + TSI108_I2C_OFFSET +
+ I2C_CNTRL1) = temp;
+
+ /* Issue the write command (at this moment all other parameters
+ * are 0 (size = 1 byte, lane = 0)
+ */
+
+ *(u32 *) (CFG_TSI108_CSR_BASE + TSI108_I2C_OFFSET +
+ I2C_CNTRL2) = (I2C_CNTRL2_START);
+
+ op_status = TSI108_I2C_TIMEOUT_ERR;
+
+ /* Wait until operation completed */
+ do {
+ /* Read I2C operation status */
+ temp = *(u32 *) (CFG_TSI108_CSR_BASE + TSI108_I2C_OFFSET + I2C_CNTRL2);
+
+ if (0 == (temp & (I2C_CNTRL2_WR_STATUS | I2C_CNTRL2_START))) {
+ if (0 == (temp &
+ (I2C_CNTRL2_I2C_CFGERR |
+ I2C_CNTRL2_I2C_TO_ERR))) {
+ op_status = TSI108_I2C_SUCCESS;
+ } else {
+ /* report detected HW error */
+ op_status = TSI108_I2C_IF_ERROR;
+
+ DPRINT (("I2C HW error reported: 0x%02x\n", temp));
+ }
+
+ break;
+ }
+
+ } while (to_count--);
+ } else {
+ op_status = TSI108_I2C_IF_BUSY;
+
+ DPRINT (("I2C Transaction start failed: 0x%02x\n", temp));
+ }
+
+ return op_status;
+}
+
+/*
+ * I2C Write interface as defined in "include/i2c.h" :
+ * chip_addr: I2C chip address, range 0..127
+ * byte_addr: Memory or register address within the chip
+ * alen: Number of bytes to use for addr (typically 1, 2 for larger
+ * memories, 0 for register type devices with only one
+ * register)
+ * buffer: Pointer to data to be written
+ * len: How many bytes to write
+ *
+ * Returns: 0 on success, not 0 on failure
+ */
+
+int i2c_write (uchar chip_addr, uint byte_addr, int alen, uchar * buffer,
+ int len)
+{
+ u32 op_status = TSI108_I2C_PARAM_ERR;
+
+ /* Check for valid I2C address */
+ if (chip_addr <= 0x7F && (byte_addr + len) <= (0x01 << (alen * 8))) {
+ while (len--) {
+ op_status =
+ i2c_write_byte (chip_addr, byte_addr++, buffer++);
+
+ if (TSI108_I2C_SUCCESS != op_status) {
+ DPRINT (("I2C write_byte() failed: 0x%02x (%d left)\n", op_status, len));
+
+ break;
+ }
+ }
+ }
+
+ return op_status;
+}
+
+/*
+ * I2C interface function as defined in "include/i2c.h".
+ * Probe the given I2C chip address by reading single byte from offset 0.
+ * Returns 0 if a chip responded, not 0 on failure.
+ */
+
+int i2c_probe (uchar chip)
+{
+ u32 tmp;
+
+ /*
+ * Try to read the first location of the chip.
+ * The Tsi108 HW doesn't support sending just the chip address
+ * and checkong for an <ACK> back.
+ */
+ return i2c_read (chip, 0, 1, (char *)&tmp, 1);
+}
+
+#endif /* (CONFIG_COMMANDS & CFG_CMD_I2C) */
+#endif /* CONFIG_TSI108_I2C */
diff --git a/drivers/tsi108_pci.c b/drivers/tsi108_pci.c
new file mode 100644
index 0000000..9f606df
--- /dev/null
+++ b/drivers/tsi108_pci.c
@@ -0,0 +1,178 @@
+/*
+ * (C) Copyright 2004 Tundra Semiconductor Corp.
+ * Alex Bounine <alexandreb@tundra.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * PCI initialisation for the Tsi108 EMU board.
+ */
+
+#include <config.h>
+
+#ifdef CONFIG_TSI108_PCI
+
+#include <common.h>
+#include <pci.h>
+#include <asm/io.h>
+#include <tsi108.h>
+
+struct pci_controller local_hose;
+
+void tsi108_clear_pci_error (void)
+{
+ u32 err_stat, err_addr, pci_stat;
+
+ /*
+ * Quietly clear errors signalled as result of PCI/X configuration read
+ * requests.
+ */
+ /* Read PB Error Log Registers */
+ err_stat = *(volatile u32 *)(CFG_TSI108_CSR_BASE +
+ TSI108_PB_REG_OFFSET + PB_ERRCS);
+ err_addr = *(volatile u32 *)(CFG_TSI108_CSR_BASE +
+ TSI108_PB_REG_OFFSET + PB_AERR);
+ if (err_stat & PB_ERRCS_ES) {
+ /* Clear PCI/X bus errors if applicable */
+ if ((err_addr & 0xFF000000) == CFG_PCI_CFG_BASE) {
+ /* Clear error flag */
+ *(u32 *) (CFG_TSI108_CSR_BASE +
+ TSI108_PB_REG_OFFSET + PB_ERRCS) =
+ PB_ERRCS_ES;
+
+ /* Clear read error reported in PB_ISR */
+ *(u32 *) (CFG_TSI108_CSR_BASE +
+ TSI108_PB_REG_OFFSET + PB_ISR) =
+ PB_ISR_PBS_RD_ERR;
+
+ /* Clear errors reported by PCI CSR (Normally Master Abort) */
+ pci_stat = *(volatile u32 *)(CFG_TSI108_CSR_BASE +
+ TSI108_PCI_REG_OFFSET +
+ PCI_CSR);
+ *(volatile u32 *)(CFG_TSI108_CSR_BASE +
+ TSI108_PCI_REG_OFFSET + PCI_CSR) =
+ pci_stat;
+
+ *(volatile u32 *)(CFG_TSI108_CSR_BASE +
+ TSI108_PCI_REG_OFFSET +
+ PCI_IRP_STAT) = PCI_IRP_STAT_P_CSR;
+ }
+ }
+
+ return;
+}
+
+unsigned int __get_pci_config_dword (u32 addr)
+{
+ unsigned int retval;
+
+ __asm__ __volatile__ (" lwbrx %0,0,%1\n"
+ "1: eieio\n"
+ "2:\n"
+ ".section .fixup,\"ax\"\n"
+ "3: li %0,-1\n"
+ " b 2b\n"
+ ".section __ex_table,\"a\"\n"
+ " .align 2\n"
+ " .long 1b,3b\n"
+ ".text":"=r"(retval):"r"(addr));
+
+ return (retval);
+}
+
+static int tsi108_read_config_dword (struct pci_controller *hose,
+ pci_dev_t dev, int offset, u32 * value)
+{
+ dev &= (CFG_PCI_CFG_SIZE - 1);
+ dev |= (CFG_PCI_CFG_BASE | (offset & 0xfc));
+ *value = __get_pci_config_dword(dev);
+ if (0xFFFFFFFF == *value)
+ tsi108_clear_pci_error ();
+ return 0;
+}
+
+static int tsi108_write_config_dword (struct pci_controller *hose,
+ pci_dev_t dev, int offset, u32 value)
+{
+ dev &= (CFG_PCI_CFG_SIZE - 1);
+ dev |= (CFG_PCI_CFG_BASE | (offset & 0xfc));
+
+ out_le32 ((volatile unsigned *)dev, value);
+
+ return 0;
+}
+
+void pci_init_board (void)
+{
+ struct pci_controller *hose = (struct pci_controller *)&local_hose;
+
+ hose->first_busno = 0;
+ hose->last_busno = 0xff;
+
+ pci_set_region (hose->regions + 0,
+ CFG_PCI_MEMORY_BUS,
+ CFG_PCI_MEMORY_PHYS,
+ CFG_PCI_MEMORY_SIZE, PCI_REGION_MEM | PCI_REGION_MEMORY);
+
+ /* PCI memory space */
+ pci_set_region (hose->regions + 1,
+ CFG_PCI_MEM_BUS,
+ CFG_PCI_MEM_PHYS, CFG_PCI_MEM_SIZE, PCI_REGION_MEM);
+
+ /* PCI I/O space */
+ pci_set_region (hose->regions + 2,
+ CFG_PCI_IO_BUS,
+ CFG_PCI_IO_PHYS, CFG_PCI_IO_SIZE, PCI_REGION_IO);
+
+ hose->region_count = 3;
+
+ pci_set_ops (hose,
+ pci_hose_read_config_byte_via_dword,
+ pci_hose_read_config_word_via_dword,
+ tsi108_read_config_dword,
+ pci_hose_write_config_byte_via_dword,
+ pci_hose_write_config_word_via_dword,
+ tsi108_write_config_dword);
+
+ pci_register_hose (hose);
+
+ hose->last_busno = pci_hose_scan (hose);
+
+ debug ("Done PCI initialization\n");
+ return;
+}
+
+#ifdef CONFIG_OF_FLAT_TREE
+void
+ft_pci_setup (void *blob, bd_t *bd)
+{
+ u32 *p;
+ int len;
+
+ p = (u32 *)ft_get_prop (blob, "/" OF_TSI "/pci@1000/bus-range", &len);
+ if (p != NULL) {
+ p[0] = local_hose.first_busno;
+ p[1] = local_hose.last_busno;
+ }
+
+}
+#endif
+
+#endif /* CONFIG_TSI108_PCI */
diff --git a/include/74xx_7xx.h b/include/74xx_7xx.h
index 33e396a..ba73bae 100644
--- a/include/74xx_7xx.h
+++ b/include/74xx_7xx.h
@@ -111,7 +111,7 @@
CPU_750CX, CPU_750FX, CPU_750GX,
CPU_7400,
CPU_7410,
- CPU_7448,
+ CPU_7447A, CPU_7448,
CPU_7450, CPU_7455, CPU_7457,
CPU_UNKNOWN} cpu_t;
diff --git a/include/asm-avr32/arch-at32ap7000/clk.h b/include/asm-avr32/arch-at32ap7000/clk.h
new file mode 100644
index 0000000..7e20d97
--- /dev/null
+++ b/include/asm-avr32/arch-at32ap7000/clk.h
@@ -0,0 +1,70 @@
+/*
+ * Copyright (C) 2006 Atmel Corporation
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef __ASM_AVR32_ARCH_CLK_H__
+#define __ASM_AVR32_ARCH_CLK_H__
+
+#ifdef CONFIG_PLL
+#define MAIN_CLK_RATE ((CFG_OSC0_HZ / CFG_PLL0_DIV) * CFG_PLL0_MUL)
+#else
+#define MAIN_CLK_RATE (CFG_OSC0_HZ)
+#endif
+
+static inline unsigned long get_cpu_clk_rate(void)
+{
+ return MAIN_CLK_RATE >> CFG_CLKDIV_CPU;
+}
+static inline unsigned long get_hsb_clk_rate(void)
+{
+ return MAIN_CLK_RATE >> CFG_CLKDIV_HSB;
+}
+static inline unsigned long get_pba_clk_rate(void)
+{
+ return MAIN_CLK_RATE >> CFG_CLKDIV_PBA;
+}
+static inline unsigned long get_pbb_clk_rate(void)
+{
+ return MAIN_CLK_RATE >> CFG_CLKDIV_PBB;
+}
+
+/* Accessors for specific devices. More will be added as needed. */
+static inline unsigned long get_sdram_clk_rate(void)
+{
+ return get_hsb_clk_rate();
+}
+static inline unsigned long get_usart_clk_rate(unsigned int dev_id)
+{
+ return get_pba_clk_rate();
+}
+static inline unsigned long get_macb_pclk_rate(unsigned int dev_id)
+{
+ return get_pbb_clk_rate();
+}
+static inline unsigned long get_macb_hclk_rate(unsigned int dev_id)
+{
+ return get_hsb_clk_rate();
+}
+static inline unsigned long get_mci_clk_rate(void)
+{
+ return get_pbb_clk_rate();
+}
+
+#endif /* __ASM_AVR32_ARCH_CLK_H__ */
diff --git a/include/asm-avr32/arch-at32ap7000/gpio.h b/include/asm-avr32/arch-at32ap7000/gpio.h
new file mode 100644
index 0000000..e4812d4
--- /dev/null
+++ b/include/asm-avr32/arch-at32ap7000/gpio.h
@@ -0,0 +1,212 @@
+/*
+ * Copyright (C) 2006 Atmel Corporation
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef __ASM_AVR32_ARCH_GPIO_H__
+#define __ASM_AVR32_ARCH_GPIO_H__
+
+#include <asm/arch/memory-map.h>
+
+#define NR_GPIO_CONTROLLERS 5
+
+/*
+ * Pin numbers identifying specific GPIO pins on the chip.
+ */
+#define GPIO_PIOA_BASE (0)
+#define GPIO_PIN_PA0 (GPIO_PIOA_BASE + 0)
+#define GPIO_PIN_PA1 (GPIO_PIOA_BASE + 1)
+#define GPIO_PIN_PA2 (GPIO_PIOA_BASE + 2)
+#define GPIO_PIN_PA3 (GPIO_PIOA_BASE + 3)
+#define GPIO_PIN_PA4 (GPIO_PIOA_BASE + 4)
+#define GPIO_PIN_PA5 (GPIO_PIOA_BASE + 5)
+#define GPIO_PIN_PA6 (GPIO_PIOA_BASE + 6)
+#define GPIO_PIN_PA7 (GPIO_PIOA_BASE + 7)
+#define GPIO_PIN_PA8 (GPIO_PIOA_BASE + 8)
+#define GPIO_PIN_PA9 (GPIO_PIOA_BASE + 9)
+#define GPIO_PIN_PA10 (GPIO_PIOA_BASE + 10)
+#define GPIO_PIN_PA11 (GPIO_PIOA_BASE + 11)
+#define GPIO_PIN_PA12 (GPIO_PIOA_BASE + 12)
+#define GPIO_PIN_PA13 (GPIO_PIOA_BASE + 13)
+#define GPIO_PIN_PA14 (GPIO_PIOA_BASE + 14)
+#define GPIO_PIN_PA15 (GPIO_PIOA_BASE + 15)
+#define GPIO_PIN_PA16 (GPIO_PIOA_BASE + 16)
+#define GPIO_PIN_PA17 (GPIO_PIOA_BASE + 17)
+#define GPIO_PIN_PA18 (GPIO_PIOA_BASE + 18)
+#define GPIO_PIN_PA19 (GPIO_PIOA_BASE + 19)
+#define GPIO_PIN_PA20 (GPIO_PIOA_BASE + 20)
+#define GPIO_PIN_PA21 (GPIO_PIOA_BASE + 21)
+#define GPIO_PIN_PA22 (GPIO_PIOA_BASE + 22)
+#define GPIO_PIN_PA23 (GPIO_PIOA_BASE + 23)
+#define GPIO_PIN_PA24 (GPIO_PIOA_BASE + 24)
+#define GPIO_PIN_PA25 (GPIO_PIOA_BASE + 25)
+#define GPIO_PIN_PA26 (GPIO_PIOA_BASE + 26)
+#define GPIO_PIN_PA27 (GPIO_PIOA_BASE + 27)
+#define GPIO_PIN_PA28 (GPIO_PIOA_BASE + 28)
+#define GPIO_PIN_PA29 (GPIO_PIOA_BASE + 29)
+#define GPIO_PIN_PA30 (GPIO_PIOA_BASE + 30)
+#define GPIO_PIN_PA31 (GPIO_PIOA_BASE + 31)
+
+#define GPIO_PIOB_BASE (GPIO_PIOA_BASE + 32)
+#define GPIO_PIN_PB0 (GPIO_PIOB_BASE + 0)
+#define GPIO_PIN_PB1 (GPIO_PIOB_BASE + 1)
+#define GPIO_PIN_PB2 (GPIO_PIOB_BASE + 2)
+#define GPIO_PIN_PB3 (GPIO_PIOB_BASE + 3)
+#define GPIO_PIN_PB4 (GPIO_PIOB_BASE + 4)
+#define GPIO_PIN_PB5 (GPIO_PIOB_BASE + 5)
+#define GPIO_PIN_PB6 (GPIO_PIOB_BASE + 6)
+#define GPIO_PIN_PB7 (GPIO_PIOB_BASE + 7)
+#define GPIO_PIN_PB8 (GPIO_PIOB_BASE + 8)
+#define GPIO_PIN_PB9 (GPIO_PIOB_BASE + 9)
+#define GPIO_PIN_PB10 (GPIO_PIOB_BASE + 10)
+#define GPIO_PIN_PB11 (GPIO_PIOB_BASE + 11)
+#define GPIO_PIN_PB12 (GPIO_PIOB_BASE + 12)
+#define GPIO_PIN_PB13 (GPIO_PIOB_BASE + 13)
+#define GPIO_PIN_PB14 (GPIO_PIOB_BASE + 14)
+#define GPIO_PIN_PB15 (GPIO_PIOB_BASE + 15)
+#define GPIO_PIN_PB16 (GPIO_PIOB_BASE + 16)
+#define GPIO_PIN_PB17 (GPIO_PIOB_BASE + 17)
+#define GPIO_PIN_PB18 (GPIO_PIOB_BASE + 18)
+#define GPIO_PIN_PB19 (GPIO_PIOB_BASE + 19)
+#define GPIO_PIN_PB20 (GPIO_PIOB_BASE + 20)
+#define GPIO_PIN_PB21 (GPIO_PIOB_BASE + 21)
+#define GPIO_PIN_PB22 (GPIO_PIOB_BASE + 22)
+#define GPIO_PIN_PB23 (GPIO_PIOB_BASE + 23)
+#define GPIO_PIN_PB24 (GPIO_PIOB_BASE + 24)
+#define GPIO_PIN_PB25 (GPIO_PIOB_BASE + 25)
+#define GPIO_PIN_PB26 (GPIO_PIOB_BASE + 26)
+#define GPIO_PIN_PB27 (GPIO_PIOB_BASE + 27)
+#define GPIO_PIN_PB28 (GPIO_PIOB_BASE + 28)
+#define GPIO_PIN_PB29 (GPIO_PIOB_BASE + 29)
+#define GPIO_PIN_PB30 (GPIO_PIOB_BASE + 30)
+
+#define GPIO_PIOC_BASE (GPIO_PIOB_BASE + 32)
+#define GPIO_PIN_PC0 (GPIO_PIOC_BASE + 0)
+#define GPIO_PIN_PC1 (GPIO_PIOC_BASE + 1)
+#define GPIO_PIN_PC2 (GPIO_PIOC_BASE + 2)
+#define GPIO_PIN_PC3 (GPIO_PIOC_BASE + 3)
+#define GPIO_PIN_PC4 (GPIO_PIOC_BASE + 4)
+#define GPIO_PIN_PC5 (GPIO_PIOC_BASE + 5)
+#define GPIO_PIN_PC6 (GPIO_PIOC_BASE + 6)
+#define GPIO_PIN_PC7 (GPIO_PIOC_BASE + 7)
+#define GPIO_PIN_PC8 (GPIO_PIOC_BASE + 8)
+#define GPIO_PIN_PC9 (GPIO_PIOC_BASE + 9)
+#define GPIO_PIN_PC10 (GPIO_PIOC_BASE + 10)
+#define GPIO_PIN_PC11 (GPIO_PIOC_BASE + 11)
+#define GPIO_PIN_PC12 (GPIO_PIOC_BASE + 12)
+#define GPIO_PIN_PC13 (GPIO_PIOC_BASE + 13)
+#define GPIO_PIN_PC14 (GPIO_PIOC_BASE + 14)
+#define GPIO_PIN_PC15 (GPIO_PIOC_BASE + 15)
+#define GPIO_PIN_PC16 (GPIO_PIOC_BASE + 16)
+#define GPIO_PIN_PC17 (GPIO_PIOC_BASE + 17)
+#define GPIO_PIN_PC18 (GPIO_PIOC_BASE + 18)
+#define GPIO_PIN_PC19 (GPIO_PIOC_BASE + 19)
+#define GPIO_PIN_PC20 (GPIO_PIOC_BASE + 20)
+#define GPIO_PIN_PC21 (GPIO_PIOC_BASE + 21)
+#define GPIO_PIN_PC22 (GPIO_PIOC_BASE + 22)
+#define GPIO_PIN_PC23 (GPIO_PIOC_BASE + 23)
+#define GPIO_PIN_PC24 (GPIO_PIOC_BASE + 24)
+#define GPIO_PIN_PC25 (GPIO_PIOC_BASE + 25)
+#define GPIO_PIN_PC26 (GPIO_PIOC_BASE + 26)
+#define GPIO_PIN_PC27 (GPIO_PIOC_BASE + 27)
+#define GPIO_PIN_PC28 (GPIO_PIOC_BASE + 28)
+#define GPIO_PIN_PC29 (GPIO_PIOC_BASE + 29)
+#define GPIO_PIN_PC30 (GPIO_PIOC_BASE + 30)
+#define GPIO_PIN_PC31 (GPIO_PIOC_BASE + 31)
+
+#define GPIO_PIOD_BASE (GPIO_PIOC_BASE + 32)
+#define GPIO_PIN_PD0 (GPIO_PIOD_BASE + 0)
+#define GPIO_PIN_PD1 (GPIO_PIOD_BASE + 1)
+#define GPIO_PIN_PD2 (GPIO_PIOD_BASE + 2)
+#define GPIO_PIN_PD3 (GPIO_PIOD_BASE + 3)
+#define GPIO_PIN_PD4 (GPIO_PIOD_BASE + 4)
+#define GPIO_PIN_PD5 (GPIO_PIOD_BASE + 5)
+#define GPIO_PIN_PD6 (GPIO_PIOD_BASE + 6)
+#define GPIO_PIN_PD7 (GPIO_PIOD_BASE + 7)
+#define GPIO_PIN_PD8 (GPIO_PIOD_BASE + 8)
+#define GPIO_PIN_PD9 (GPIO_PIOD_BASE + 9)
+#define GPIO_PIN_PD10 (GPIO_PIOD_BASE + 10)
+#define GPIO_PIN_PD11 (GPIO_PIOD_BASE + 11)
+#define GPIO_PIN_PD12 (GPIO_PIOD_BASE + 12)
+#define GPIO_PIN_PD13 (GPIO_PIOD_BASE + 13)
+#define GPIO_PIN_PD14 (GPIO_PIOD_BASE + 14)
+#define GPIO_PIN_PD15 (GPIO_PIOD_BASE + 15)
+#define GPIO_PIN_PD16 (GPIO_PIOD_BASE + 16)
+#define GPIO_PIN_PD17 (GPIO_PIOD_BASE + 17)
+
+#define GPIO_PIOE_BASE (GPIO_PIOD_BASE + 32)
+#define GPIO_PIN_PE0 (GPIO_PIOE_BASE + 0)
+#define GPIO_PIN_PE1 (GPIO_PIOE_BASE + 1)
+#define GPIO_PIN_PE2 (GPIO_PIOE_BASE + 2)
+#define GPIO_PIN_PE3 (GPIO_PIOE_BASE + 3)
+#define GPIO_PIN_PE4 (GPIO_PIOE_BASE + 4)
+#define GPIO_PIN_PE5 (GPIO_PIOE_BASE + 5)
+#define GPIO_PIN_PE6 (GPIO_PIOE_BASE + 6)
+#define GPIO_PIN_PE7 (GPIO_PIOE_BASE + 7)
+#define GPIO_PIN_PE8 (GPIO_PIOE_BASE + 8)
+#define GPIO_PIN_PE9 (GPIO_PIOE_BASE + 9)
+#define GPIO_PIN_PE10 (GPIO_PIOE_BASE + 10)
+#define GPIO_PIN_PE11 (GPIO_PIOE_BASE + 11)
+#define GPIO_PIN_PE12 (GPIO_PIOE_BASE + 12)
+#define GPIO_PIN_PE13 (GPIO_PIOE_BASE + 13)
+#define GPIO_PIN_PE14 (GPIO_PIOE_BASE + 14)
+#define GPIO_PIN_PE15 (GPIO_PIOE_BASE + 15)
+#define GPIO_PIN_PE16 (GPIO_PIOE_BASE + 16)
+#define GPIO_PIN_PE17 (GPIO_PIOE_BASE + 17)
+#define GPIO_PIN_PE18 (GPIO_PIOE_BASE + 18)
+#define GPIO_PIN_PE19 (GPIO_PIOE_BASE + 19)
+#define GPIO_PIN_PE20 (GPIO_PIOE_BASE + 20)
+#define GPIO_PIN_PE21 (GPIO_PIOE_BASE + 21)
+#define GPIO_PIN_PE22 (GPIO_PIOE_BASE + 22)
+#define GPIO_PIN_PE23 (GPIO_PIOE_BASE + 23)
+#define GPIO_PIN_PE24 (GPIO_PIOE_BASE + 24)
+#define GPIO_PIN_PE25 (GPIO_PIOE_BASE + 25)
+#define GPIO_PIN_PE26 (GPIO_PIOE_BASE + 26)
+
+static inline void *gpio_pin_to_addr(unsigned int pin)
+{
+ switch (pin >> 5) {
+ case 0:
+ return (void *)PIOA_BASE;
+ case 1:
+ return (void *)PIOB_BASE;
+ case 2:
+ return (void *)PIOC_BASE;
+ case 3:
+ return (void *)PIOD_BASE;
+ case 4:
+ return (void *)PIOE_BASE;
+ default:
+ return NULL;
+ }
+}
+
+void gpio_select_periph_A(unsigned int pin, int use_pullup);
+void gpio_select_periph_B(unsigned int pin, int use_pullup);
+
+void gpio_enable_ebi(void);
+void gpio_enable_usart0(void);
+void gpio_enable_usart1(void);
+void gpio_enable_usart2(void);
+void gpio_enable_usart3(void);
+void gpio_enable_macb0(void);
+void gpio_enable_macb1(void);
+void gpio_enable_mmci(void);
+
+#endif /* __ASM_AVR32_ARCH_GPIO_H__ */
diff --git a/include/asm-avr32/arch-at32ap7000/hmatrix2.h b/include/asm-avr32/arch-at32ap7000/hmatrix2.h
index e6df4b7..b0e787a 100644
--- a/include/asm-avr32/arch-at32ap7000/hmatrix2.h
+++ b/include/asm-avr32/arch-at32ap7000/hmatrix2.h
@@ -224,9 +224,9 @@
| HMATRIX2_BF(name,value))
/* Register access macros */
-#define hmatrix2_readl(port,reg) \
- readl((port)->regs + HMATRIX2_##reg)
-#define hmatrix2_writel(port,reg,value) \
- writel((value), (port)->regs + HMATRIX2_##reg)
+#define hmatrix2_readl(reg) \
+ readl((void *)HMATRIX_BASE + HMATRIX2_##reg)
+#define hmatrix2_writel(reg,value) \
+ writel((value), (void *)HMATRIX_BASE + HMATRIX2_##reg)
#endif /* __ASM_AVR32_HMATRIX2_H__ */
diff --git a/include/asm-avr32/arch-at32ap7000/memory-map.h b/include/asm-avr32/arch-at32ap7000/memory-map.h
index 8ffe851..5513e88 100644
--- a/include/asm-avr32/arch-at32ap7000/memory-map.h
+++ b/include/asm-avr32/arch-at32ap7000/memory-map.h
@@ -19,43 +19,48 @@
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
-#ifndef __ASM_AVR32_PART_MEMORY_MAP_H__
-#define __ASM_AVR32_PART_MEMORY_MAP_H__
+#ifndef __AT32AP7000_MEMORY_MAP_H__
+#define __AT32AP7000_MEMORY_MAP_H__
-#define AUDIOC_BASE 0xFFF02800
-#define DAC_BASE 0xFFF02000
-#define DMAC_BASE 0xFF200000
-#define ECC_BASE 0xFFF03C00
-#define HISI_BASE 0xFFF02C00
-#define HMATRIX_BASE 0xFFF00800
-#define HSDRAMC_BASE 0xFFF03800
-#define HSMC_BASE 0xFFF03400
-#define LCDC_BASE 0xFF000000
-#define MACB0_BASE 0xFFF01800
-#define MACB1_BASE 0xFFF01C00
-#define MMCI_BASE 0xFFF02400
-#define PIOA_BASE 0xFFE02800
-#define PIOB_BASE 0xFFE02C00
-#define PIOC_BASE 0xFFE03000
-#define PIOD_BASE 0xFFE03400
-#define PIOE_BASE 0xFFE03800
-#define PSIF_BASE 0xFFE03C00
-#define PWM_BASE 0xFFF01400
-#define SM_BASE 0xFFF00000
-#define INTC_BASE 0XFFF00400
-#define SPI0_BASE 0xFFE00000
-#define SPI1_BASE 0xFFE00400
-#define SSC0_BASE 0xFFE01C00
-#define SSC1_BASE 0xFFE02000
-#define SSC2_BASE 0xFFE02400
-#define TIMER0_BASE 0xFFF00C00
-#define TIMER1_BASE 0xFFF01000
-#define TWI_BASE 0xFFE00800
-#define USART0_BASE 0xFFE00C00
-#define USART1_BASE 0xFFE01000
-#define USART2_BASE 0xFFE01400
-#define USART3_BASE 0xFFE01800
-#define USB_FIFO 0xFF300000
-#define USB_BASE 0xFFF03000
+/* Devices on the High Speed Bus (HSB) */
+#define LCDC_BASE 0xFF000000
+#define DMAC_BASE 0xFF200000
+#define USB_FIFO 0xFF300000
+
+/* Devices on Peripheral Bus A (PBA) */
+#define SPI0_BASE 0xFFE00000
+#define SPI1_BASE 0xFFE00400
+#define TWI_BASE 0xFFE00800
+#define USART0_BASE 0xFFE00C00
+#define USART1_BASE 0xFFE01000
+#define USART2_BASE 0xFFE01400
+#define USART3_BASE 0xFFE01800
+#define SSC0_BASE 0xFFE01C00
+#define SSC1_BASE 0xFFE02000
+#define SSC2_BASE 0xFFE02400
+#define PIOA_BASE 0xFFE02800
+#define PIOB_BASE 0xFFE02C00
+#define PIOC_BASE 0xFFE03000
+#define PIOD_BASE 0xFFE03400
+#define PIOE_BASE 0xFFE03800
+#define PSIF_BASE 0xFFE03C00
+
+/* Devices on Peripheral Bus B (PBB) */
+#define SM_BASE 0xFFF00000
+#define INTC_BASE 0xFFF00400
+#define HMATRIX_BASE 0xFFF00800
+#define TIMER0_BASE 0xFFF00C00
+#define TIMER1_BASE 0xFFF01000
+#define PWM_BASE 0xFFF01400
+#define MACB0_BASE 0xFFF01800
+#define MACB1_BASE 0xFFF01C00
+#define DAC_BASE 0xFFF02000
+#define MMCI_BASE 0xFFF02400
+#define AUDIOC_BASE 0xFFF02800
+#define HISI_BASE 0xFFF02C00
+#define USB_BASE 0xFFF03000
+#define HSMC_BASE 0xFFF03400
+#define HSDRAMC_BASE 0xFFF03800
+#define ECC_BASE 0xFFF03C00
-#endif /* __ASM_AVR32_PART_MEMORY_MAP_H__ */
+#endif /* __AT32AP7000_MEMORY_MAP_H__ */
diff --git a/include/asm-avr32/arch-at32ap7000/mmc.h b/include/asm-avr32/arch-at32ap7000/mmc.h
new file mode 100644
index 0000000..fcfbbb3
--- /dev/null
+++ b/include/asm-avr32/arch-at32ap7000/mmc.h
@@ -0,0 +1,96 @@
+/*
+ * Copyright (C) 2004-2006 Atmel Corporation
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef __ASM_AVR32_MMC_H
+#define __ASM_AVR32_MMC_H
+
+struct mmc_cid {
+ unsigned long psn;
+ unsigned short oid;
+ unsigned char mid;
+ unsigned char prv;
+ unsigned char mdt;
+ char pnm[7];
+};
+
+struct mmc_csd
+{
+ u8 csd_structure:2,
+ spec_vers:4,
+ rsvd1:2;
+ u8 taac;
+ u8 nsac;
+ u8 tran_speed;
+ u16 ccc:12,
+ read_bl_len:4;
+ u64 read_bl_partial:1,
+ write_blk_misalign:1,
+ read_blk_misalign:1,
+ dsr_imp:1,
+ rsvd2:2,
+ c_size:12,
+ vdd_r_curr_min:3,
+ vdd_r_curr_max:3,
+ vdd_w_curr_min:3,
+ vdd_w_curr_max:3,
+ c_size_mult:3,
+ sector_size:5,
+ erase_grp_size:5,
+ wp_grp_size:5,
+ wp_grp_enable:1,
+ default_ecc:2,
+ r2w_factor:3,
+ write_bl_len:4,
+ write_bl_partial:1,
+ rsvd3:5;
+ u8 file_format_grp:1,
+ copy:1,
+ perm_write_protect:1,
+ tmp_write_protect:1,
+ file_format:2,
+ ecc:2;
+ u8 crc:7;
+ u8 one:1;
+};
+
+/* MMC Command numbers */
+#define MMC_CMD_GO_IDLE_STATE 0
+#define MMC_CMD_SEND_OP_COND 1
+#define MMC_CMD_ALL_SEND_CID 2
+#define MMC_CMD_SET_RELATIVE_ADDR 3
+#define MMC_CMD_SD_SEND_RELATIVE_ADDR 3
+#define MMC_CMD_SET_DSR 4
+#define MMC_CMD_SELECT_CARD 7
+#define MMC_CMD_SEND_CSD 9
+#define MMC_CMD_SEND_CID 10
+#define MMC_CMD_SEND_STATUS 13
+#define MMC_CMD_SET_BLOCKLEN 16
+#define MMC_CMD_READ_SINGLE_BLOCK 17
+#define MMC_CMD_READ_MULTIPLE_BLOCK 18
+#define MMC_CMD_WRITE_BLOCK 24
+#define MMC_CMD_APP_CMD 55
+
+#define MMC_ACMD_SD_SEND_OP_COND 41
+
+#define R1_ILLEGAL_COMMAND (1 << 22)
+#define R1_APP_CMD (1 << 5)
+
+#endif /* __ASM_AVR32_MMC_H */
diff --git a/include/asm-avr32/arch-at32ap7000/platform.h b/include/asm-avr32/arch-at32ap7000/platform.h
deleted file mode 100644
index 7590501..0000000
--- a/include/asm-avr32/arch-at32ap7000/platform.h
+++ /dev/null
@@ -1,146 +0,0 @@
-/*
- * Copyright (C) 2005-2006 Atmel Corporation
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-#ifndef _ASM_AVR32_ARCH_PM_H
-#define _ASM_AVR32_ARCH_PM_H
-
-#include <config.h>
-
-enum clock_domain_id {
- CLOCK_CPU,
- CLOCK_HSB,
- CLOCK_PBA,
- CLOCK_PBB,
- NR_CLOCK_DOMAINS,
-};
-
-enum resource_type {
- RESOURCE_GPIO,
- RESOURCE_CLOCK,
-};
-
-enum gpio_func {
- GPIO_FUNC_GPIO,
- GPIO_FUNC_A,
- GPIO_FUNC_B,
-};
-
-enum device_id {
- DEVICE_HEBI,
- DEVICE_PBA_BRIDGE,
- DEVICE_PBB_BRIDGE,
- DEVICE_HRAMC,
- /* GPIO controllers must be kept together */
- DEVICE_PIOA,
- DEVICE_PIOB,
- DEVICE_PIOC,
- DEVICE_PIOD,
- DEVICE_PIOE,
- DEVICE_SM,
- DEVICE_INTC,
- DEVICE_HMATRIX,
-#if defined(CFG_HPDC)
- DEVICE_HPDC,
-#endif
-#if defined(CFG_MACB0)
- DEVICE_MACB0,
-#endif
-#if defined(CFG_MACB1)
- DEVICE_MACB1,
-#endif
-#if defined(CFG_LCDC)
- DEVICE_LCDC,
-#endif
-#if defined(CFG_USART0)
- DEVICE_USART0,
-#endif
-#if defined(CFG_USART1)
- DEVICE_USART1,
-#endif
-#if defined(CFG_USART2)
- DEVICE_USART2,
-#endif
-#if defined(CFG_USART3)
- DEVICE_USART3,
-#endif
-#if defined(CFG_MMCI)
- DEVICE_MMCI,
-#endif
-#if defined(CFG_DMAC)
- DEVICE_DMAC,
-#endif
- NR_DEVICES,
- NO_DEVICE = -1,
-};
-
-struct resource {
- enum resource_type type;
- union {
- struct {
- unsigned long base;
- } iomem;
- struct {
- unsigned char nr_pins;
- enum device_id gpio_dev;
- enum gpio_func func;
- unsigned short start;
- } gpio;
- struct {
- enum clock_domain_id id;
- unsigned char index;
- } clock;
- } u;
-};
-
-struct device {
- void *regs;
- unsigned int nr_resources;
- const struct resource *resource;
-};
-
-struct clock_domain {
- unsigned short reg;
- enum clock_domain_id id;
- enum device_id bridge;
-};
-
-extern const struct device chip_device[NR_DEVICES];
-extern const struct clock_domain chip_clock[NR_CLOCK_DOMAINS];
-
-/**
- * Set up PIO, clock management and I/O memory for a device.
- */
-const struct device *get_device(enum device_id devid);
-void put_device(const struct device *dev);
-
-int gpio_set_func(enum device_id gpio_devid, unsigned int start,
- unsigned int nr_pins, enum gpio_func func);
-void gpio_free(enum device_id gpio_devid, unsigned int start,
- unsigned int nr_pins);
-
-void pm_init(void);
-int pm_enable_clock(enum clock_domain_id id, unsigned int index);
-void pm_disable_clock(enum clock_domain_id id, unsigned int index);
-unsigned long pm_get_clock_freq(enum clock_domain_id domain);
-
-void cpu_enable_sdram(void);
-
-#endif /* _ASM_AVR32_ARCH_PM_H */
diff --git a/include/asm-avr32/global_data.h b/include/asm-avr32/global_data.h
index 01d836c..681c514 100644
--- a/include/asm-avr32/global_data.h
+++ b/include/asm-avr32/global_data.h
@@ -35,10 +35,8 @@
typedef struct global_data {
bd_t *bd;
unsigned long flags;
- const struct device *console_uart;
- const struct device *sm;
unsigned long baudrate;
- unsigned long sdram_size;
+ unsigned long stack_end; /* highest stack address */
unsigned long have_console; /* serial_init() was called */
unsigned long reloc_off; /* Relocation Offset */
unsigned long env_addr; /* Address of env struct */
diff --git a/include/asm-avr32/initcalls.h b/include/asm-avr32/initcalls.h
index 7ba25cd..583e5dc 100644
--- a/include/asm-avr32/initcalls.h
+++ b/include/asm-avr32/initcalls.h
@@ -26,8 +26,6 @@
extern int cpu_init(void);
extern int timer_init(void);
-extern void board_init_memories(void);
-extern void board_init_pio(void);
extern void board_init_info(void);
#endif /* __ASM_AVR32_INITCALLS_H__ */
diff --git a/include/asm-blackfin/arch-bf533/bf533_serial.h b/include/asm-blackfin/arch-bf533/bf533_serial.h
index ce58863..65749ee 100644
--- a/include/asm-blackfin/arch-bf533/bf533_serial.h
+++ b/include/asm-blackfin/arch-bf533/bf533_serial.h
@@ -1,7 +1,7 @@
/*
* U-boot bf533_serial.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _BF533_SERIAL_H_
diff --git a/include/asm-blackfin/arch-bf533/bf5xx_rtc.h b/include/asm-blackfin/arch-bf533/bf5xx_rtc.h
index bc09922..f4440a8 100644
--- a/include/asm-blackfin/arch-bf533/bf5xx_rtc.h
+++ b/include/asm-blackfin/arch-bf533/bf5xx_rtc.h
@@ -1,7 +1,7 @@
/*
* U-boot - bf533_rtc.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _BF533_RTC_H_
diff --git a/include/asm-blackfin/arch-bf533/cplbtab.h b/include/asm-blackfin/arch-bf533/cplbtab.h
deleted file mode 100644
index 89f0325..0000000
--- a/include/asm-blackfin/arch-bf533/cplbtab.h
+++ /dev/null
@@ -1,482 +0,0 @@
-/*This file is subject to the terms and conditions of the GNU General Public
- * License.
- *
- * Blackfin BF533/2.6 support : LG Soft India
- * Updated : Ashutosh Singh / Jahid Khan : Rrap Software Pvt Ltd
- * Updated : 1. SDRAM_KERNEL, SDRAM_DKENEL are added as initial cplb's
- * shouldn't be victimized. cplbmgr.S search logic is corrected
- * to findout the appropriate victim.
- * 2. SDRAM_IGENERIC in dpdt_table is replaced with SDRAM_DGENERIC
- * : LG Soft India
- */
-#include <config.h>
-
-#ifndef __ARCH_BFINNOMMU_CPLBTAB_H
-#define __ARCH_BFINNOMMU_CPLBTAB_H
-
-/*************************************************************************
- * ICPLB TABLE
- *************************************************************************/
-
-.data
-/* This table is configurable */
- .align 4;
-
-/* Data Attibutes*/
-
-#define SDRAM_IGENERIC (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_USER_RD | CPLB_VALID)
-#define SDRAM_IKERNEL (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_USER_RD | CPLB_VALID | CPLB_LOCK)
-#define L1_IMEMORY (PAGE_SIZE_1MB | CPLB_L1_CHBL | CPLB_USER_RD | CPLB_VALID | CPLB_LOCK)
-#define SDRAM_INON_CHBL (PAGE_SIZE_4MB | CPLB_USER_RD | CPLB_VALID)
-
-/*Use the menuconfig cache policy here - CONFIG_BLKFIN_WT/CONFIG_BLKFIN_WB*/
-
-#define ANOMALY_05000158 0x200
-#ifdef CONFIG_BLKFIN_WB /*Write Back Policy */
-#define SDRAM_DGENERIC (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_DIRTY | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158)
-#define SDRAM_DNON_CHBL (PAGE_SIZE_4MB | CPLB_DIRTY | CPLB_SUPV_WR | CPLB_USER_RD | CPLB_USER_WR | CPLB_VALID | ANOMALY_05000158)
-#define SDRAM_DKERNEL (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_USER_RD | CPLB_USER_WR | CPLB_DIRTY | CPLB_SUPV_WR | CPLB_VALID | CPLB_LOCK | ANOMALY_05000158)
-#define L1_DMEMORY (PAGE_SIZE_4KB | CPLB_L1_CHBL | CPLB_DIRTY | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158)
-#define SDRAM_EBIU (PAGE_SIZE_4MB | CPLB_DIRTY | CPLB_USER_RD | CPLB_USER_WR | CPLB_SUPV_WR | CPLB_VALID | ANOMALY_05000158)
-
-#else /*Write Through */
-#define SDRAM_DGENERIC (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_WT | CPLB_L1_AOW | CPLB_SUPV_WR | CPLB_USER_RD | CPLB_USER_WR | CPLB_VALID | ANOMALY_05000158)
-#define SDRAM_DNON_CHBL (PAGE_SIZE_4MB | CPLB_WT | CPLB_L1_AOW | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158)
-#define SDRAM_DKERNEL (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_WT | CPLB_L1_AOW | CPLB_USER_RD | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_VALID | CPLB_LOCK | ANOMALY_05000158)
-#define L1_DMEMORY (PAGE_SIZE_4KB | CPLB_L1_CHBL | CPLB_L1_AOW | CPLB_WT | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_VALID | ANOMALY_05000158)
-#define SDRAM_EBIU (PAGE_SIZE_4MB | CPLB_WT | CPLB_L1_AOW | CPLB_USER_RD | CPLB_USER_WR | CPLB_SUPV_WR | CPLB_VALID | ANOMALY_05000158)
-#endif
-
-.align 4;
-.global _ipdt_table _ipdt_table:.byte4 0x00000000;
-.byte4(SDRAM_IKERNEL); /*SDRAM_Page0 */
-.byte4 0x00400000;
-.byte4(SDRAM_IKERNEL); /*SDRAM_Page1 */
-.byte4 0x00800000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page2 */
-.byte4 0x00C00000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page3 */
-.byte4 0x01000000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page4 */
-.byte4 0x01400000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page5 */
-.byte4 0x01800000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page6 */
-.byte4 0x01C00000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page7 */
-#ifndef CONFIG_EZKIT /*STAMP Memory regions */
-.byte4 0x02000000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page8 */
-.byte4 0x02400000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page9 */
-.byte4 0x02800000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page10 */
-.byte4 0x02C00000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page11 */
-.byte4 0x03000000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page12 */
-.byte4 0x03400000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page13 */
-.byte4 0x03800000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page14 */
-.byte4 0x03C00000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page15 */
-#endif
-.byte4 0x20000000;
-.byte4(SDRAM_EBIU); /* Async Memory Bank 2 (Secnd) */
-
-#ifdef CONFIG_STAMP
-.byte4 0x04000000;
-.byte4(SDRAM_IGENERIC);
-.byte4 0x04400000;
-.byte4(SDRAM_IGENERIC);
-.byte4 0x04800000;
-.byte4(SDRAM_IGENERIC);
-.byte4 0x04C00000;
-.byte4(SDRAM_IGENERIC);
-.byte4 0x05000000;
-.byte4(SDRAM_IGENERIC);
-.byte4 0x05400000;
-.byte4(SDRAM_IGENERIC);
-.byte4 0x05800000;
-.byte4(SDRAM_IGENERIC);
-.byte4 0x05C00000;
-.byte4(SDRAM_IGENERIC);
-.byte4 0x06000000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page25 */
-.byte4 0x06400000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page26 */
-.byte4 0x06800000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page27 */
-.byte4 0x06C00000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page28 */
-.byte4 0x07000000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page29 */
-.byte4 0x07400000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page30 */
-.byte4 0x07800000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page31 */
-.byte4 0x07C00000;
-.byte4(SDRAM_IKERNEL); /*SDRAM_Page32 */
-#endif
-.byte4 0xffffffff; /* end of section - termination */
-
-/**********************************************************************
- * PAGE DESCRIPTOR TABLE
- *
- **********************************************************************/
-
-/* Till here we are discussing about the static memory management model.
- * However, the operating envoronments commonly define more CPLB
- * descriptors to cover the entire addressable memory than will fit into
- * the available on-chip 16 CPLB MMRs. When this happens, the below table
- * will be used which will hold all the potentially required CPLB descriptors
- *
- * This is how Page descriptor Table is implemented in uClinux/Blackfin.
- */
-.global _dpdt_table _dpdt_table:.byte4 0x00000000;
-.byte4(SDRAM_DKERNEL); /*SDRAM_Page0 */
-.byte4 0x00400000;
-.byte4(SDRAM_DKERNEL); /*SDRAM_Page1 */
-.byte4 0x00800000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page2 */
-.byte4 0x00C00000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page3 */
-.byte4 0x01000000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page4 */
-.byte4 0x01400000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page5 */
-.byte4 0x01800000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page6 */
-.byte4 0x01C00000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page7 */
-
-#ifndef CONFIG_EZKIT
-.byte4 0x02000000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page8 */
-.byte4 0x02400000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page9 */
-.byte4 0x02800000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page10 */
-.byte4 0x02C00000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page11 */
-.byte4 0x03000000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page12 */
-.byte4 0x03400000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page13 */
-.byte4 0x03800000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page14 */
-.byte4 0x03C00000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page15 */
-#endif
-
-#ifdef CONFIG_STAMP
-.byte4 0x04000000;
-.byte4(SDRAM_DGENERIC);
-.byte4 0x04400000;
-.byte4(SDRAM_DGENERIC);
-.byte4 0x04800000;
-.byte4(SDRAM_DGENERIC);
-.byte4 0x04C00000;
-.byte4(SDRAM_DGENERIC);
-.byte4 0x05000000;
-.byte4(SDRAM_DGENERIC);
-.byte4 0x05400000;
-.byte4(SDRAM_DGENERIC);
-.byte4 0x05800000;
-.byte4(SDRAM_DGENERIC);
-.byte4 0x05C00000;
-.byte4(SDRAM_DGENERIC);
-.byte4 0x06000000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page25 */
-.byte4 0x06400000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page26 */
-.byte4 0x06800000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page27 */
-.byte4 0x06C00000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page28 */
-.byte4 0x07000000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page29 */
-.byte4 0x07400000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page30 */
-.byte4 0x07800000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page31 */
-.byte4 0x07C00000;
-.byte4(SDRAM_DKERNEL); /*SDRAM_Page32 */
-#endif
-
-.byte4 0x20000000;
-.byte4(SDRAM_EBIU); /* Async Memory Bank 0 (Prim A) */
-
-#if (BFIN_CPU == ADSP_BF533)
-.byte4 0xFF800000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF801000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF802000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF803000;
-.byte4(L1_DMEMORY);
-#endif
-.byte4 0xFF804000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF805000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF806000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF807000;
-.byte4(L1_DMEMORY);
-#if (BFIN_CPU == ADSP_BF533)
-.byte4 0xFF900000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF901000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF902000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF903000;
-.byte4(L1_DMEMORY);
-#endif
-#if ((BFIN_CPU == ADSP_BF532) || (BFIN_CPU == ADSP_BF533))
-.byte4 0xFF904000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF905000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF906000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF907000;
-.byte4(L1_DMEMORY);
-#endif
-.byte4 0xFFB00000;
-.byte4(L1_DMEMORY);
-
-.byte4 0xffffffff; /*end of section - termination */
-
-#ifdef CONFIG_CPLB_INFO
-.global _ipdt_swapcount_table; /* swapin count first, then swapout count */
-_ipdt_swapcount_table:
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 10 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 20 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 30 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 40 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 50 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 60 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 70 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 80 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 90 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 100 */
-
-.global _dpdt_swapcount_table; /* swapin count first, then swapout count */
-_dpdt_swapcount_table:
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 10 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 20 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 30 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 40 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 50 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 60 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 70 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 80 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 80 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 100 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 110 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 120 */
-#endif
-
-#endif /*__ARCH_BFINNOMMU_CPLBTAB_H*/
diff --git a/include/asm-blackfin/arch-bf533/irq.h b/include/asm-blackfin/arch-bf533/irq.h
index 9c5230d..3235745 100644
--- a/include/asm-blackfin/arch-bf533/irq.h
+++ b/include/asm-blackfin/arch-bf533/irq.h
@@ -1,7 +1,7 @@
/*
* U-boot bf533_irq.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on
* linux/arch/$(ARCH)/platform/$(PLATFORM)/irq.c
@@ -33,8 +33,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _BF533_IRQ_H_
diff --git a/include/asm-blackfin/arch-bf537/bf537_serial.h b/include/asm-blackfin/arch-bf537/bf537_serial.h
index 1610411..64088f2 100644
--- a/include/asm-blackfin/arch-bf537/bf537_serial.h
+++ b/include/asm-blackfin/arch-bf537/bf537_serial.h
@@ -1,7 +1,7 @@
/*
* U-boot bf537_serial.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _BF537_SERIAL_H_
diff --git a/include/asm-blackfin/arch-bf537/bf5xx_rtc.h b/include/asm-blackfin/arch-bf537/bf5xx_rtc.h
index 0043e42..db5cc6f 100644
--- a/include/asm-blackfin/arch-bf537/bf5xx_rtc.h
+++ b/include/asm-blackfin/arch-bf537/bf5xx_rtc.h
@@ -1,7 +1,7 @@
/*
* U-boot - bf537_rtc.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _BF537_RTC_H_
diff --git a/include/asm-blackfin/arch-bf537/cplbtab.h b/include/asm-blackfin/arch-bf537/cplbtab.h
deleted file mode 100644
index c5151bb..0000000
--- a/include/asm-blackfin/arch-bf537/cplbtab.h
+++ /dev/null
@@ -1,408 +0,0 @@
-/*This file is subject to the terms and conditions of the GNU General Public
- * License.
- *
- * Blackfin BF533/2.6 support : LG Soft India
- * Updated : Ashutosh Singh / Jahid Khan : Rrap Software Pvt Ltd
- * Updated : 1. SDRAM_KERNEL, SDRAM_DKENEL are added as initial cplb's
- * shouldn't be victimized. cplbmgr.S search logic is corrected
- * to findout the appropriate victim.
- * 2. SDRAM_IGENERIC in dpdt_table is replaced with SDRAM_DGENERIC
- * : LG Soft India
- */
-#include <config.h>
-
-#ifndef __ARCH_BFINNOMMU_CPLBTAB_H
-#define __ARCH_BFINNOMMU_CPLBTAB_H
-
-/*
- * ICPLB TABLE
- */
-
-.data
-/* This table is configurable */
- .align 4;
-
-/* Data Attibutes*/
-
-#define SDRAM_IGENERIC (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_USER_RD | CPLB_VALID)
-#define SDRAM_IKERNEL (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_USER_RD | CPLB_VALID | CPLB_LOCK)
-#define L1_IMEMORY (PAGE_SIZE_1MB | CPLB_L1_CHBL | CPLB_USER_RD | CPLB_VALID | CPLB_LOCK)
-#define SDRAM_INON_CHBL (PAGE_SIZE_4MB | CPLB_USER_RD | CPLB_VALID)
-
-/*Use the menuconfig cache policy here - CONFIG_BLKFIN_WT/CONFIG_BLKFIN_WB*/
-
-#define ANOMALY_05000158 0x200
-#ifdef CONFIG_BLKFIN_WB /*Write Back Policy */
-#define SDRAM_DGENERIC (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_DIRTY | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158)
-#define SDRAM_DNON_CHBL (PAGE_SIZE_4MB | CPLB_DIRTY | CPLB_SUPV_WR | CPLB_USER_RD | CPLB_USER_WR | CPLB_VALID | ANOMALY_05000158)
-#define SDRAM_DKERNEL (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_USER_RD | CPLB_USER_WR | CPLB_DIRTY | CPLB_SUPV_WR | CPLB_VALID | CPLB_LOCK | ANOMALY_05000158)
-#define L1_DMEMORY (PAGE_SIZE_4KB | CPLB_L1_CHBL | CPLB_DIRTY | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158)
-#define SDRAM_EBIU (PAGE_SIZE_4MB | CPLB_DIRTY | CPLB_USER_RD | CPLB_USER_WR | CPLB_SUPV_WR | CPLB_VALID | ANOMALY_05000158)
-
-#else /*Write Through */
-#define SDRAM_DGENERIC (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_WT | CPLB_L1_AOW | CPLB_SUPV_WR | CPLB_USER_RD | CPLB_USER_WR | CPLB_VALID | ANOMALY_05000158)
-#define SDRAM_DNON_CHBL (PAGE_SIZE_4MB | CPLB_WT | CPLB_L1_AOW | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158)
-#define SDRAM_DKERNEL (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_WT | CPLB_L1_AOW | CPLB_USER_RD | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_VALID | CPLB_LOCK | ANOMALY_05000158)
-#define L1_DMEMORY (PAGE_SIZE_4KB | CPLB_L1_CHBL | CPLB_L1_AOW | CPLB_WT | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_VALID | ANOMALY_05000158)
-#define SDRAM_EBIU (PAGE_SIZE_4MB | CPLB_WT | CPLB_L1_AOW | CPLB_USER_RD | CPLB_USER_WR | CPLB_SUPV_WR | CPLB_VALID | ANOMALY_05000158)
-#endif
-
-.align 4;
-.global _ipdt_table _ipdt_table:.byte4 0x00000000;
-.byte4(SDRAM_IKERNEL); /*SDRAM_Page0 */
-.byte4 0x00400000;
-.byte4(SDRAM_IKERNEL); /*SDRAM_Page1 */
-.byte4 0x00800000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page2 */
-.byte4 0x00C00000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page3 */
-.byte4 0x01000000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page4 */
-.byte4 0x01400000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page5 */
-.byte4 0x01800000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page6 */
-.byte4 0x01C00000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page7 */
-.byte4 0x02000000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page8 */
-.byte4 0x02400000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page9 */
-.byte4 0x02800000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page10 */
-.byte4 0x02C00000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page11 */
-.byte4 0x03000000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page12 */
-.byte4 0x03400000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page13 */
-.byte4 0x03800000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page14 */
-.byte4 0x03C00000;
-.byte4(SDRAM_IGENERIC); /*SDRAM_Page15 */
-.byte4 0x20000000;
-.byte4(SDRAM_EBIU); /* Async Memory Bank 2 (Secnd) */
-
-.byte4 0xffffffff; /* end of section - termination */
-
-/*
- * PAGE DESCRIPTOR TABLE
- *
- */
-
-/*
- * Till here we are discussing about the static memory management model.
- * However, the operating envoronments commonly define more CPLB
- * descriptors to cover the entire addressable memory than will fit into
- * the available on-chip 16 CPLB MMRs. When this happens, the below table
- * will be used which will hold all the potentially required CPLB descriptors
- *
- * This is how Page descriptor Table is implemented in uClinux/Blackfin.
- */
-.global _dpdt_table _dpdt_table:.byte4 0x00000000;
-.byte4(SDRAM_DKERNEL); /*SDRAM_Page0 */
-.byte4 0x00400000;
-.byte4(SDRAM_DKERNEL); /*SDRAM_Page1 */
-.byte4 0x00800000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page2 */
-.byte4 0x00C00000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page3 */
-.byte4 0x01000000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page4 */
-.byte4 0x01400000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page5 */
-.byte4 0x01800000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page6 */
-.byte4 0x01C00000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page7 */
-.byte4 0x02000000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page8 */
-.byte4 0x02400000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page9 */
-.byte4 0x02800000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page10 */
-.byte4 0x02C00000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page11 */
-.byte4 0x03000000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page12 */
-.byte4 0x03400000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page13 */
-.byte4 0x03800000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page14 */
-.byte4 0x03C00000;
-.byte4(SDRAM_DGENERIC); /*SDRAM_Page15 */
-.byte4 0x20000000;
-.byte4(SDRAM_EBIU); /* Async Memory Bank 0 (Prim A) */
-
-#if ((BFIN_CPU == ADSP_BF534) || (BFIN_CPU == ADSP_BF537))
-.byte4 0xFF800000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF801000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF802000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF803000;
-.byte4(L1_DMEMORY);
-#endif
-.byte4 0xFF804000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF805000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF806000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF807000;
-.byte4(L1_DMEMORY);
-#if ((BFIN_CPU == ADSP_BF534) || (BFIN_CPU == ADSP_BF537))
-.byte4 0xFF900000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF901000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF902000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF903000;
-.byte4(L1_DMEMORY);
-#endif
-.byte4 0xFF904000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF905000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF906000;
-.byte4(L1_DMEMORY);
-.byte4 0xFF907000;
-.byte4(L1_DMEMORY);
-
-.byte4 0xFFB00000;
-.byte4(L1_DMEMORY);
-
-.byte4 0xffffffff; /*end of section - termination */
-
-#ifdef CONFIG_CPLB_INFO
-.global _ipdt_swapcount_table; /* swapin count first, then swapout count */
-_ipdt_swapcount_table:
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 10 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 20 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 30 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 40 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 50 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 60 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 70 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 80 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 90 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 100 */
-
-.global _dpdt_swapcount_table; /* swapin count first, then swapout count */
-_dpdt_swapcount_table:
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 10 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 20 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 30 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 40 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 50 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 60 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 70 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 80 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 80 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 100 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 110 */
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000;
-.byte4 0x00000000; /* 120 */
-
-#endif
-
-#endif /*__ARCH_BFINNOMMU_CPLBTAB_H*/
diff --git a/include/asm-blackfin/arch-bf537/irq.h b/include/asm-blackfin/arch-bf537/irq.h
index 4cb4c15..527d8a2 100644
--- a/include/asm-blackfin/arch-bf537/irq.h
+++ b/include/asm-blackfin/arch-bf537/irq.h
@@ -1,7 +1,7 @@
/*
* U-boot bf537_irq.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on
* linux/arch/$(ARCH)/platform/$(PLATFORM)/irq.c
@@ -33,8 +33,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _BF537_IRQ_H_
diff --git a/include/asm-blackfin/arch-bf561/bf561_serial.h b/include/asm-blackfin/arch-bf561/bf561_serial.h
index 0810228..eb01ca2 100644
--- a/include/asm-blackfin/arch-bf561/bf561_serial.h
+++ b/include/asm-blackfin/arch-bf561/bf561_serial.h
@@ -1,7 +1,7 @@
/*
* U-boot bf561_serial.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _BF561_SERIAL_H_
diff --git a/include/asm-blackfin/arch-common/bf53x_rtc.h b/include/asm-blackfin/arch-common/bf53x_rtc.h
index bc09922..f4440a8 100644
--- a/include/asm-blackfin/arch-common/bf53x_rtc.h
+++ b/include/asm-blackfin/arch-common/bf53x_rtc.h
@@ -1,7 +1,7 @@
/*
* U-boot - bf533_rtc.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _BF533_RTC_H_
diff --git a/include/asm-blackfin/bitops.h b/include/asm-blackfin/bitops.h
index 7766c4a..438e50b 100644
--- a/include/asm-blackfin/bitops.h
+++ b/include/asm-blackfin/bitops.h
@@ -1,7 +1,7 @@
/*
* U-boot - bitops.h Routines for bit operations
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _BLACKFIN_BITOPS_H
diff --git a/include/asm-blackfin/blackfin.h b/include/asm-blackfin/blackfin.h
index 0ec9207..bf502a4 100644
--- a/include/asm-blackfin/blackfin.h
+++ b/include/asm-blackfin/blackfin.h
@@ -1,7 +1,7 @@
/*
* U-boot - blackfin.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _BLACKFIN_H_
diff --git a/include/asm-blackfin/blackfin_defs.h b/include/asm-blackfin/blackfin_defs.h
index 2190215..451d29c 100644
--- a/include/asm-blackfin/blackfin_defs.h
+++ b/include/asm-blackfin/blackfin_defs.h
@@ -1,7 +1,7 @@
/*
* U-boot - blackfin_defs.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef __BLACKFIN_DEFS_H__
diff --git a/include/asm-blackfin/byteorder.h b/include/asm-blackfin/byteorder.h
index 3b4df4e..a1a52a5 100644
--- a/include/asm-blackfin/byteorder.h
+++ b/include/asm-blackfin/byteorder.h
@@ -1,7 +1,7 @@
/*
* U-boot - byteorder.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _BLACKFIN_BYTEORDER_H
diff --git a/include/asm-blackfin/cplb.h b/include/asm-blackfin/cplb.h
index dd695e1..9d8d9ec 100644
--- a/include/asm-blackfin/cplb.h
+++ b/include/asm-blackfin/cplb.h
@@ -50,7 +50,7 @@
#define SDRAM_IGENERIC (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_USER_RD | CPLB_VALID)
#define SDRAM_IKERNEL (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_USER_RD | CPLB_VALID | CPLB_LOCK)
-#define L1_IMEMORY (PAGE_SIZE_1MB | CPLB_L1_CHBL | CPLB_USER_RD | CPLB_VALID | CPLB_LOCK)
+#define L1_IMEMORY (PAGE_SIZE_1MB | CPLB_USER_RD | CPLB_VALID | CPLB_LOCK)
#define SDRAM_INON_CHBL (PAGE_SIZE_4MB | CPLB_USER_RD | CPLB_VALID)
/*Use the menuconfig cache policy here - CONFIG_BLKFIN_WT/CONFIG_BLKFIN_WB*/
@@ -61,20 +61,20 @@
#define SDRAM_DGENERIC (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_DIRTY | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158)
#define SDRAM_DNON_CHBL (PAGE_SIZE_4MB | CPLB_DIRTY | CPLB_SUPV_WR | CPLB_USER_RD | CPLB_USER_WR | CPLB_VALID | ANOMALY_05000158)
#define SDRAM_DKERNEL (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_USER_RD | CPLB_USER_WR | CPLB_DIRTY | CPLB_SUPV_WR | CPLB_VALID | CPLB_LOCK | ANOMALY_05000158)
-#define L1_DMEMORY (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_DIRTY | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158)
+#define L1_DMEMORY (PAGE_SIZE_4MB | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158)
#define SDRAM_EBIU (PAGE_SIZE_4MB | CPLB_DIRTY | CPLB_USER_RD | CPLB_USER_WR | CPLB_SUPV_WR | CPLB_VALID | ANOMALY_05000158)
#else /*Write Through */
#define SDRAM_DGENERIC (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_WT | CPLB_L1_AOW | CPLB_SUPV_WR | CPLB_USER_RD | CPLB_USER_WR | CPLB_VALID | ANOMALY_05000158)
#define SDRAM_DNON_CHBL (PAGE_SIZE_4MB | CPLB_WT | CPLB_L1_AOW | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158)
#define SDRAM_DKERNEL (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_WT | CPLB_L1_AOW | CPLB_USER_RD | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_VALID | CPLB_LOCK | ANOMALY_05000158)
-#define L1_DMEMORY (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_L1_AOW | CPLB_WT | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_VALID | ANOMALY_05000158)
+#define L1_DMEMORY (PAGE_SIZE_4MB | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_VALID | ANOMALY_05000158)
#define SDRAM_EBIU (PAGE_SIZE_4MB | CPLB_WT | CPLB_L1_AOW | CPLB_USER_RD | CPLB_USER_WR | CPLB_SUPV_WR | CPLB_VALID | ANOMALY_05000158)
#endif
#if defined(CONFIG_BF561)
-#define page_descriptor_table_size (CONFIG_MEM_SIZE/4 + 2) /* SDRAM +L1 + ASYNC_Memory */
+#define page_descriptor_table_size (CONFIG_MEM_SIZE/4 + 1 + 4) /* SDRAM +L1 + ASYNC_Memory */
#else
-#define page_descriptor_table_size (CONFIG_MEM_SIZE/4 + 1 + 3) /* SDRAM + L1 + ASYNC_Memory */
+#define page_descriptor_table_size (CONFIG_MEM_SIZE/4 + 2) /* SDRAM + L1 + ASYNC_Memory */
#endif
#endif /* _CPLB_H */
diff --git a/include/asm-blackfin/current.h b/include/asm-blackfin/current.h
index 108c279..ed2b851 100644
--- a/include/asm-blackfin/current.h
+++ b/include/asm-blackfin/current.h
@@ -1,7 +1,7 @@
/*
* U-boot - current.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _BLACKFIN_CURRENT_H
diff --git a/include/asm-blackfin/delay.h b/include/asm-blackfin/delay.h
index 0c01e9f..ea0b366 100644
--- a/include/asm-blackfin/delay.h
+++ b/include/asm-blackfin/delay.h
@@ -1,7 +1,7 @@
/*
* U-boot - delay.h Routines for introducing delays
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _BLACKFIN_DELAY_H
diff --git a/include/asm-blackfin/entry.h b/include/asm-blackfin/entry.h
index b64d406..eb84f11 100644
--- a/include/asm-blackfin/entry.h
+++ b/include/asm-blackfin/entry.h
@@ -1,7 +1,7 @@
/*
* U-boot - entry.h Routines for context saving and restoring
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef __BLACKFIN_ENTRY_H
@@ -27,7 +27,6 @@
#include <linux/config.h>
#include <asm/setup.h>
-#include <asm/page.h>
/*
* Stack layout in 'ret_from_exception':
diff --git a/include/asm-blackfin/errno.h b/include/asm-blackfin/errno.h
index 713bba0..0d2c618 100644
--- a/include/asm-blackfin/errno.h
+++ b/include/asm-blackfin/errno.h
@@ -1,7 +1,7 @@
/*
* U-boot - errno.h Error number defines
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _BLACKFIN_ERRNO_H
diff --git a/include/asm-blackfin/global_data.h b/include/asm-blackfin/global_data.h
index 1c73853..9024d0a 100644
--- a/include/asm-blackfin/global_data.h
+++ b/include/asm-blackfin/global_data.h
@@ -1,7 +1,7 @@
/*
* U-boot - global_data.h Declarations for global data of u-boot
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef __ASM_GBL_DATA_H
diff --git a/include/asm-blackfin/hw_irq.h b/include/asm-blackfin/hw_irq.h
index baa3e0c..9b36055 100644
--- a/include/asm-blackfin/hw_irq.h
+++ b/include/asm-blackfin/hw_irq.h
@@ -1,7 +1,7 @@
/*
* U-boot - hw_irq.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on
* linux/arch/$(ARCH)/platform/$(PLATFORM)/hw_irq.h
@@ -24,8 +24,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <linux/config.h>
diff --git a/include/asm-blackfin/io-kernel.h b/include/asm-blackfin/io-kernel.h
index 3c087c3..5d0ad06 100644
--- a/include/asm-blackfin/io-kernel.h
+++ b/include/asm-blackfin/io-kernel.h
@@ -1,7 +1,7 @@
/*
* U-boot - io-kernel.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _BLACKFIN_IO_H
diff --git a/include/asm-blackfin/io.h b/include/asm-blackfin/io.h
index 6bab6e7..332d2c6 100644
--- a/include/asm-blackfin/io.h
+++ b/include/asm-blackfin/io.h
@@ -1,7 +1,7 @@
/*
* U-boot - io.h IO routines
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _BLACKFIN_IO_H
@@ -37,6 +37,7 @@
static inline void sync(void)
{
+ __builtin_bfin_ssync();
}
/*
diff --git a/include/asm-blackfin/irq.h b/include/asm-blackfin/irq.h
index aede742..1fff316 100644
--- a/include/asm-blackfin/irq.h
+++ b/include/asm-blackfin/irq.h
@@ -1,7 +1,7 @@
/*
* U-boot - irq.h Interrupt related header file
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file was based on
* linux/arch/$(ARCH)/platform/$(PLATFORM)/irq.c
@@ -31,8 +31,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _BLACKFIN_IRQ_H_
diff --git a/include/asm-blackfin/linkage.h b/include/asm-blackfin/linkage.h
index 18f0c36..4fc1acf 100644
--- a/include/asm-blackfin/linkage.h
+++ b/include/asm-blackfin/linkage.h
@@ -1,7 +1,7 @@
/*
* U-boot - linkage.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _LINUX_LINKAGE_H
diff --git a/include/asm-blackfin/machdep.h b/include/asm-blackfin/machdep.h
index 4fea74c..8bf9473 100644
--- a/include/asm-blackfin/machdep.h
+++ b/include/asm-blackfin/machdep.h
@@ -1,7 +1,7 @@
/*
* U-boot - machdep.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _BLACKFIN_MACHDEP_H
diff --git a/include/asm-blackfin/mem_init.h b/include/asm-blackfin/mem_init.h
index d9d8bf9..cb448ad 100644
--- a/include/asm-blackfin/mem_init.h
+++ b/include/asm-blackfin/mem_init.h
@@ -1,7 +1,7 @@
/*
* U-boot - mem_init.h Header file for memory initialization
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#if (CONFIG_MEM_MT48LC16M16A2TG_75 || \
diff --git a/include/asm-blackfin/page.h b/include/asm-blackfin/page.h
deleted file mode 100644
index d59828c..0000000
--- a/include/asm-blackfin/page.h
+++ /dev/null
@@ -1,123 +0,0 @@
-/*
- * U-boot - page.h
- *
- * Copyright (c) 2005 blackfin.uclinux.org
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef _BLACKFIN_PAGE_H
-#define _BLACKFIN_PAGE_H
-
-#include <linux/config.h>
-
-/* PAGE_SHIFT determines the page size */
-
-#define PAGE_SHIFT (12)
-#define PAGE_SIZE (4096)
-#define PAGE_MASK (~(PAGE_SIZE-1))
-
-#ifdef __KERNEL__
-
-#include <asm/setup.h>
-
-#if PAGE_SHIFT < 13
-#define KTHREAD_SIZE (8192)
-#else
-#define KTHREAD_SIZE PAGE_SIZE
-#endif
-
-#ifndef __ASSEMBLY__
-
-#define get_user_page(vaddr) __get_free_page(GFP_KERNEL)
-#define free_user_page(page, addr) free_page(addr)
-
-#define clear_page(page) memset((page), 0, PAGE_SIZE)
-#define copy_page(to,from) memcpy((to), (from), PAGE_SIZE)
-
-#define clear_user_page(page, vaddr) clear_page(page)
-#define copy_user_page(to, from, vaddr) copy_page(to, from)
-
-/*
- * These are used to make use of C type-checking..
- */
-typedef struct {
- unsigned long pte;
-} pte_t;
-typedef struct {
- unsigned long pmd[16];
-} pmd_t;
-typedef struct {
- unsigned long pgd;
-} pgd_t;
-typedef struct {
- unsigned long pgprot;
-} pgprot_t;
-
-#define pte_val(x) ((x).pte)
-#define pmd_val(x) ((&x)->pmd[0])
-#define pgd_val(x) ((x).pgd)
-#define pgprot_val(x) ((x).pgprot)
-
-#define __pte(x) ((pte_t) { (x) } )
-#define __pmd(x) ((pmd_t) { (x) } )
-#define __pgd(x) ((pgd_t) { (x) } )
-#define __pgprot(x) ((pgprot_t) { (x) } )
-
-/* to align the pointer to the (next) page boundary */
-#define PAGE_ALIGN(addr) (((addr)+PAGE_SIZE-1)&PAGE_MASK)
-
-/* Pure 2^n version of get_order */
-extern __inline__ int get_order(unsigned long size)
-{
- int order;
-
- size = (size - 1) >> (PAGE_SHIFT - 1);
- order = -1;
- do {
- size >>= 1;
- order++;
- } while (size);
- return order;
-}
-
-#endif /* !__ASSEMBLY__ */
-
-#include <asm/page_offset.h>
-
-#define PAGE_OFFSET (PAGE_OFFSET_RAW)
-
-#ifndef __ASSEMBLY__
-
-#define __pa(vaddr) virt_to_phys((void *)vaddr)
-#define __va(paddr) phys_to_virt((unsigned long)paddr)
-
-#define MAP_NR(addr) (((unsigned long)(addr)-PAGE_OFFSET) >> PAGE_SHIFT)
-#define virt_to_page(addr) (mem_map + (((unsigned long)(addr)-PAGE_OFFSET) >> PAGE_SHIFT))
-#define VALID_PAGE(page) ((page - mem_map) < max_mapnr)
-
-#define PAGE_BUG(page) do { \
- BUG(); \
-} while (0)
-
-#endif
-
-#endif
-
-#endif
diff --git a/include/asm-blackfin/page_offset.h b/include/asm-blackfin/page_offset.h
index 262473f..cfd8f1f 100644
--- a/include/asm-blackfin/page_offset.h
+++ b/include/asm-blackfin/page_offset.h
@@ -1,7 +1,7 @@
/*
* U-boot - page_offset.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
/*
diff --git a/include/asm-blackfin/posix_types.h b/include/asm-blackfin/posix_types.h
index f1f2b5f..27889e8 100644
--- a/include/asm-blackfin/posix_types.h
+++ b/include/asm-blackfin/posix_types.h
@@ -1,7 +1,7 @@
/*
* U-boot - posix_types.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef __ARCH_BLACKFIN_POSIX_TYPES_H
diff --git a/include/asm-blackfin/processor.h b/include/asm-blackfin/processor.h
index df49bed..6cd4f56 100644
--- a/include/asm-blackfin/processor.h
+++ b/include/asm-blackfin/processor.h
@@ -1,7 +1,7 @@
/*
* U-boot - processor.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on
* include/asm-m68k/processor.h
@@ -23,8 +23,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef __ASM_BLACKFIN_PROCESSOR_H
diff --git a/include/asm-blackfin/ptrace.h b/include/asm-blackfin/ptrace.h
index afd5777..f1b7d00 100644
--- a/include/asm-blackfin/ptrace.h
+++ b/include/asm-blackfin/ptrace.h
@@ -1,7 +1,7 @@
/*
* U-boot - ptrace.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _BLACKFIN_PTRACE_H
diff --git a/include/asm-blackfin/segment.h b/include/asm-blackfin/segment.h
index 9e6d817..f309543 100644
--- a/include/asm-blackfin/segment.h
+++ b/include/asm-blackfin/segment.h
@@ -1,7 +1,7 @@
/*
* U-boot - segment.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _BLACKFIN_SEGMENT_H
diff --git a/include/asm-blackfin/setup.h b/include/asm-blackfin/setup.h
index a3c1715..b6b8267 100644
--- a/include/asm-blackfin/setup.h
+++ b/include/asm-blackfin/setup.h
@@ -1,7 +1,7 @@
/*
* U-boot - setup.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on
* asm/setup.h -- Definition of the Linux/Blackfin setup information
@@ -22,8 +22,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _BLACKFIN_SETUP_H
diff --git a/include/asm-blackfin/shared_resources.h b/include/asm-blackfin/shared_resources.h
index fbef186..d280ffe 100644
--- a/include/asm-blackfin/shared_resources.h
+++ b/include/asm-blackfin/shared_resources.h
@@ -1,7 +1,7 @@
/*
* U-boot - setup.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _SHARED_RESOURCES_H_
diff --git a/include/asm-blackfin/string.h b/include/asm-blackfin/string.h
index aac6bc9..dd50207 100644
--- a/include/asm-blackfin/string.h
+++ b/include/asm-blackfin/string.h
@@ -1,7 +1,7 @@
/*
* U-boot - string.h String functions
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
/* Changed by Lineo Inc. May 2001 */
@@ -30,7 +30,6 @@
#ifdef __KERNEL__ /* only set these up for kernel code */
#include <asm/setup.h>
-#include <asm/page.h>
#include <config.h>
#include <asm/blackfin.h>
diff --git a/include/asm-blackfin/system.h b/include/asm-blackfin/system.h
index 0e53adf..eda887f 100644
--- a/include/asm-blackfin/system.h
+++ b/include/asm-blackfin/system.h
@@ -1,7 +1,7 @@
/*
* U-boot - system.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _BLACKFIN_SYSTEM_H
diff --git a/include/asm-blackfin/traps.h b/include/asm-blackfin/traps.h
index 29e6eba..b90ceda 100644
--- a/include/asm-blackfin/traps.h
+++ b/include/asm-blackfin/traps.h
@@ -1,7 +1,7 @@
/*
* U-boot - traps.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on
* linux/include/asm/traps.h
@@ -23,8 +23,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
/*
diff --git a/include/asm-blackfin/types.h b/include/asm-blackfin/types.h
index 942ed27..665a419 100644
--- a/include/asm-blackfin/types.h
+++ b/include/asm-blackfin/types.h
@@ -1,7 +1,7 @@
/*
* U-boot - types.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _BLACKFIN_TYPES_H
diff --git a/include/asm-blackfin/u-boot.h b/include/asm-blackfin/u-boot.h
index e1a435a..b4928da 100644
--- a/include/asm-blackfin/u-boot.h
+++ b/include/asm-blackfin/u-boot.h
@@ -1,7 +1,7 @@
/*
* U-boot - u-boot.h Structure declarations for board specific data
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,15 +21,15 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef _U_BOOT_H_
#define _U_BOOT_H_ 1
typedef struct bd_info {
- int bi_baudrate; /* serial console baudrate */
+ int bi_baudrate; /* serial console baudrate */
unsigned long bi_ip_addr; /* IP Address */
unsigned char bi_enetaddr[6]; /* Ethernet adress */
unsigned long bi_arch_number; /* unique id for this board */
diff --git a/include/asm-blackfin/uaccess.h b/include/asm-blackfin/uaccess.h
index 61e2bfe..6e913bb 100644
--- a/include/asm-blackfin/uaccess.h
+++ b/include/asm-blackfin/uaccess.h
@@ -1,7 +1,7 @@
/*
* U-boot - uaccess.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* This file is based on
* Based on: include/asm-m68knommu/uaccess.h
@@ -22,8 +22,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef __BLACKFIN_UACCESS_H
diff --git a/include/asm-blackfin/virtconvert.h b/include/asm-blackfin/virtconvert.h
index 769f5a0..9eda9f8 100644
--- a/include/asm-blackfin/virtconvert.h
+++ b/include/asm-blackfin/virtconvert.h
@@ -1,7 +1,7 @@
/*
* U-boot - virtconvert.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef __BLACKFIN_VIRT_CONVERT__
@@ -33,7 +33,6 @@
#include <linux/config.h>
#include <asm/setup.h>
-#include <asm/page.h>
#define mm_vtop(vaddr) ((unsigned long) vaddr)
#define mm_ptov(vaddr) ((unsigned long) vaddr)
diff --git a/include/asm-microblaze/microblaze_intc.h b/include/asm-microblaze/microblaze_intc.h
new file mode 100644
index 0000000..6635aea
--- /dev/null
+++ b/include/asm-microblaze/microblaze_intc.h
@@ -0,0 +1,40 @@
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal SIMEK <monstr@monstr.cz>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+typedef volatile struct microblaze_intc_t {
+ int isr; /* interrupt status register */
+ int ipr; /* interrupt pending register */
+ int ier; /* interrupt enable register */
+ int iar; /* interrupt acknowledge register */
+ int sie; /* set interrupt enable bits */
+ int cie; /* clear interrupt enable bits */
+ int ivr; /* interrupt vector register */
+ int mer; /* master enable register */
+} microblaze_intc_t;
+
+struct irq_action {
+ interrupt_handler_t *handler; /* pointer to interrupt rutine */
+ void *arg;
+ int count; /* number of interrupt */
+};
diff --git a/include/asm-microblaze/microblaze_timer.h b/include/asm-microblaze/microblaze_timer.h
new file mode 100644
index 0000000..844c8db
--- /dev/null
+++ b/include/asm-microblaze/microblaze_timer.h
@@ -0,0 +1,41 @@
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal SIMEK <monstr@monstr.cz>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#define TIMER_ENABLE_ALL 0x400 /* ENALL */
+#define TIMER_PWM 0x200 /* PWMA0 */
+#define TIMER_INTERRUPT 0x100 /* T0INT */
+#define TIMER_ENABLE 0x080 /* ENT0 */
+#define TIMER_ENABLE_INTR 0x040 /* ENIT0 */
+#define TIMER_RESET 0x020 /* LOAD0 */
+#define TIMER_RELOAD 0x010 /* ARHT0 */
+#define TIMER_EXT_CAPTURE 0x008 /* CAPT0 */
+#define TIMER_EXT_COMPARE 0x004 /* GENT0 */
+#define TIMER_DOWN_COUNT 0x002 /* UDT0 */
+#define TIMER_CAPTURE_MODE 0x001 /* MDT0 */
+
+typedef volatile struct microblaze_timer_t {
+ int control; /* control/statuc register TCSR */
+ int loadreg; /* load register TLR */
+ int counter; /* timer/counter register */
+} microblaze_timer_t;
diff --git a/include/asm-microblaze/suzaku.h b/include/asm-microblaze/suzaku.h
deleted file mode 100644
index c57a144..0000000
--- a/include/asm-microblaze/suzaku.h
+++ /dev/null
@@ -1,27 +0,0 @@
-/*
- * (C) Copyright 2004 Atmark Techno, Inc.
- *
- * Yasushi SHOJI <yashi@atmark-techno.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/* System Register (GPIO) */
-#define MICROBLAZE_SYSREG_BASE_ADDR 0xFFFFA000
-#define MICROBLAZE_SYSREG_RECONFIGURE (1 << 0)
diff --git a/include/asm-ppc/global_data.h b/include/asm-ppc/global_data.h
index c113b7e..26bc875 100644
--- a/include/asm-ppc/global_data.h
+++ b/include/asm-ppc/global_data.h
@@ -49,6 +49,9 @@
unsigned long scc_clk;
unsigned long brg_clk;
#endif
+#if defined(CONFIG_MPC7448HPC2)
+ unsigned long mem_clk;
+#endif
#if defined(CONFIG_MPC83XX)
/* There are other clocks in the MPC83XX */
u32 csb_clk;
diff --git a/include/asm-ppc/gpio.h b/include/asm-ppc/gpio.h
new file mode 100644
index 0000000..114dc92
--- /dev/null
+++ b/include/asm-ppc/gpio.h
@@ -0,0 +1,56 @@
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* 4xx PPC's have 2 GPIO controllers */
+#if defined(CONFIG_405EZ) || \
+ defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
+ defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
+#define GPIO_GROUP_MAX 2
+#else
+#define GPIO_GROUP_MAX 1
+#endif
+
+#define GPIO_MAX 32
+#define GPIO_ALT1_SEL 0x40000000
+#define GPIO_ALT2_SEL 0x80000000
+#define GPIO_ALT3_SEL 0xc0000000
+#define GPIO_IN_SEL 0x40000000
+#define GPIO_MASK 0xc0000000
+
+#define GPIO_VAL(gpio) (0x80000000 >> (gpio))
+
+#ifndef __ASSEMBLY__
+typedef enum gpio_select { GPIO_SEL, GPIO_ALT1, GPIO_ALT2, GPIO_ALT3 } gpio_select_t;
+typedef enum gpio_driver { GPIO_DIS, GPIO_IN, GPIO_OUT, GPIO_BI } gpio_driver_t;
+typedef enum gpio_out { GPIO_OUT_0, GPIO_OUT_1, GPIO_OUT_NO_CHG } gpio_out_t;
+
+typedef struct {
+ unsigned long add; /* gpio core base address */
+ gpio_driver_t in_out; /* Driver Setting */
+ gpio_select_t alt_nb; /* Selected Alternate */
+} gpio_param_s;
+#endif
+
+void gpio_config(int pin, int in_out, int gpio_alt, int out_val);
+void gpio_write_bit(int pin, int val);
+void gpio_set_chip_configuration(void);
diff --git a/include/configs/MPC8360EMDS.h b/include/configs/MPC8360EMDS.h
index d2af0e1..79937dc 100644
--- a/include/configs/MPC8360EMDS.h
+++ b/include/configs/MPC8360EMDS.h
@@ -342,8 +342,12 @@
#endif
/* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_LIBFDT 1
+#undef CONFIG_OF_FLAT_TREE
#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_HAS_BD_T 1
+#define CONFIG_OF_HAS_UBOOT_ENV 1
+
/* maximum size of the flat tree (8K) */
#define OF_FLAT_TREE_MAX_SIZE 8192
diff --git a/include/configs/acadia.h b/include/configs/acadia.h
index 9e02ca3..35b6a51 100644
--- a/include/configs/acadia.h
+++ b/include/configs/acadia.h
@@ -31,20 +31,18 @@
/*-----------------------------------------------------------------------
* High Level Configuration Options
*----------------------------------------------------------------------*/
-#define CONFIG_ACADIA 1 /* Board is Acadia */
-#define CONFIG_4xx 1 /* ... PPC4xx family */
-#define CONFIG_405EZ 1 /* Specifc 405EZ support*/
-#undef CFG_DRAM_TEST /* Disable-takes long time */
+#define CONFIG_ACADIA 1 /* Board is Acadia */
+#define CONFIG_4xx 1 /* ... PPC4xx family */
+#define CONFIG_405EZ 1 /* Specifc 405EZ support*/
#define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
+#define CONFIG_MISC_INIT_F 1 /* Call misc_init_f */
#define CONFIG_NO_SERIAL_EEPROM
/*#undef CONFIG_NO_SERIAL_EEPROM*/
#ifdef CONFIG_NO_SERIAL_EEPROM
-
/*----------------------------------------------------------------------------
* PLL settings for 266MHz CPU, 133MHz PLB/SDRAM, 66MHz EBC, 33MHz PCI,
* assuming a 66MHz input clock to the 405EZ.
@@ -59,24 +57,125 @@
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_FLASH_BASE 0xFE000000
#define CFG_MONITOR_LEN (256 * 1024)/* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN (384 * 1024)/* Reserve 128 kB for malloc() */
+#define CFG_MALLOC_LEN (512 * 1024)/* Reserve 512 kB for malloc() */
+
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0xfe000000
#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_CPLD_BASE 0x80000000
+#define CFG_NAND_ADDR 0xd0000000
#define CFG_USB_HOST 0xef603000 /* USB OHCI 1.1 controller */
-/*
- * Define here the location of the environment variables (FLASH).
- * Note: DENX encourages to use redundant environment in FLASH. NVRAM is only
- * supported for backward compatibility.
- */
+/*-----------------------------------------------------------------------
+ * Initial RAM & stack pointer
+ *----------------------------------------------------------------------*/
+#define CFG_TEMP_STACK_OCM 1 /* OCM as init ram */
+
+/* On Chip Memory location */
+#define CFG_OCM_DATA_ADDR 0xF8000000
+#define CFG_OCM_DATA_SIZE 0x4000 /* 16K of onchip SRAM */
+#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SRAM */
+#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */
+
+#define CFG_GBL_DATA_SIZE 128 /* size for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */
+#define CFG_BASE_BAUD 691200
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SERIAL_MULTI 1
+
+/* The following table includes the supported baudrates */
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
- #define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
#else
- #define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
+#define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
+#define CFG_ENV_IS_EMBEDDED 1 /* use embedded environment */
#endif
+/*-----------------------------------------------------------------------
+ * FLASH related
+ *----------------------------------------------------------------------*/
+#define CFG_FLASH_CFI /* The flash is CFI compatible */
+#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
+
+#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE}
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+
+#ifdef CFG_ENV_IS_IN_FLASH
+#define CFG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */
+#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+
+/* Address and size of Redundant Environment Sector */
+#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#endif
+
+/*-----------------------------------------------------------------------
+ * RAM (CRAM)
+ *----------------------------------------------------------------------*/
+#define CFG_MBYTES_RAM 64 /* 64MB */
+
+/*-----------------------------------------------------------------------
+ * I2C
+ *----------------------------------------------------------------------*/
+#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+
+#define CFG_I2C_MULTI_EEPROMS
+#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+
+/* I2C SYSMON (LM75, AD7414 is almost compatible) */
+#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
+#define CONFIG_DTT_AD7414 1 /* use AD7414 */
+#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
+#define CFG_DTT_MAX_TEMP 70
+#define CFG_DTT_LOW_TEMP -30
+#define CFG_DTT_HYSTERESIS 3
+
+#if 0 /* test-only... */
+/*-----------------------------------------------------------------------
+ * SPI stuff - Define to include SPI control
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_SPI
+#endif
+
+/*-----------------------------------------------------------------------
+ * Ethernet
+ *----------------------------------------------------------------------*/
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_NET_MULTI 1
+#define CFG_RX_ETH_BUFFER 16 /* # of rx buffers & descriptors*/
+
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+
#define CONFIG_PREBOOT "echo;" \
"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
"echo"
@@ -122,13 +221,6 @@
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
-#define CONFIG_NET_MULTI 1
-#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-
#define CONFIG_USB_OHCI
#define CONFIG_USB_STORAGE
@@ -166,7 +258,6 @@
CFG_CMD_PCI | \
CFG_CMD_PING | \
CFG_CMD_REGINFO | \
- CFG_CMD_SDRAM | \
CFG_CMD_USB)
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
@@ -174,76 +265,34 @@
#undef CONFIG_WATCHDOG /* watchdog disabled */
-/*
+/*-----------------------------------------------------------------------
* Miscellaneous configurable options
- */
+ *----------------------------------------------------------------------*/
#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-/*-----------------------------------------------------------------------
- * Serial Port
- *----------------------------------------------------------------------*/
-#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */
-#define CFG_BASE_BAUD 691200
-#define CONFIG_BAUDRATE 115200
-
-/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-
-/*-----------------------------------------------------------------------
- * I2C
- *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
-
-#define CFG_I2C_MULTI_EEPROMS
-#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
-#define CFG_I2C_EEPROM_ADDR_LEN 1
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
-#define CFG_EEPROM_PAGE_WRITE_BITS 3
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
-
-/* I2C SYSMON (LM75, AD7414 is almost compatible) */
-#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
-#define CONFIG_DTT_AD7414 1 /* use AD7414 */
-#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
-#define CFG_DTT_MAX_TEMP 70
-#define CFG_DTT_LOW_TEMP -30
-#define CFG_DTT_HYSTERESIS 3
-
-#if 0 /* test-only... */
-/*-----------------------------------------------------------------------
- * SPI stuff - Define to include SPI control
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SPI
-#endif
-
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
@@ -251,39 +300,13 @@
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH related
- *----------------------------------------------------------------------*/
-#define CFG_FLASH_CFI
-#define CFG_FLASH_CFI_DRIVER
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-
-#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE}
-#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
-#define CFG_MAX_FLASH_SECT 1024 /* sectors per device */
-
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#ifdef CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
-#endif
-
#ifdef TEST_ONLY_NAND
/*-----------------------------------------------------------------------
* NAND FLASH
*----------------------------------------------------------------------*/
#define CFG_MAX_NAND_DEVICE 1
#define NAND_MAX_CHIPS 1
-#define CFG_NAND_BASE (CFG_NAND + CFG_NAND_CS)
+#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS)
#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
#endif
@@ -297,50 +320,42 @@
#endif
/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in data cache)
- */
-/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM 1
-
-/* On Chip Memory location */
-#define CFG_OCM_DATA_ADDR 0xF8000000
-#define CFG_OCM_DATA_SIZE 0x4000 /* 16K of onchip SRAM */
-#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SRAM */
-#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */
-
-#define CFG_GBL_DATA_SIZE 128 /* size for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
- */
-#define CFG_NAND 0xd0000000
+ *----------------------------------------------------------------------*/
#define CFG_NAND_CS 0 /* NAND chip connected to CSx */
-/* Memory Bank 0 (Flash) initialization */
+/* Memory Bank 0 (Flash) initialization */
#define CFG_EBC_PB0AP 0x03337200
-#define CFG_EBC_PB0CR 0xfe0bc000 /* BAS=0xFE0,BS=32MB,BU=R/W,BW=32bit */
+#define CFG_EBC_PB0CR 0xfe0bc000
-/* Memory Bank 1 (CRAM) initialization */
+/* Just initial configuration for CRAM. Will be changed in memory.c to sync mode*/
+/* Memory Bank 1 (CRAM) initialization */
#define CFG_EBC_PB1AP 0x030400c0
#define CFG_EBC_PB1CR 0x000bc000
-/* Memory Bank 2 (CRAM) initialization */
+/* Memory Bank 2 (CRAM) initialization */
#define CFG_EBC_PB2AP 0x030400c0
#define CFG_EBC_PB2CR 0x020bc000
/* Memory Bank 3 (NAND-FLASH) initialization */
#define CFG_EBC_PB3AP 0x018003c0
-#define CFG_EBC_PB3CR (CFG_NAND | 0x1c000)
+#define CFG_EBC_PB3CR (CFG_NAND_ADDR | 0x1c000)
-/* Memory Bank 4 (CPLD) initialization */
+/* Memory Bank 4 (CPLD) initialization */
#define CFG_EBC_PB4AP 0x04006000
-#define CFG_EBC_PB4CR 0x80018000 /* BAS=0x000,BS=16MB,BU=R/W,BW=32bit */
+#define CFG_EBC_PB4CR (CFG_CPLD_BASE | 0x18000)
#define CFG_EBC_CFG 0xf8400000
/*-----------------------------------------------------------------------
+ * GPIO Setup
+ *----------------------------------------------------------------------*/
+#define CFG_GPIO_CRAM_CLK 8
+#define CFG_GPIO_CRAM_WAIT 9
+#define CFG_GPIO_CRAM_ADV 10
+#define CFG_GPIO_CRAM_CRE (32 + 21)
+
+/*-----------------------------------------------------------------------
* Definitions for GPIO_0 setup (PPC405EZ specific)
*
* GPIO0[0-3] - External Bus Controller CS_4 - CS_7 Outputs
@@ -389,25 +404,6 @@
#define CFG_GPIO1_TSRL 0x00000000
#define CFG_GPIO1_TCR 0xFFFF8014
-/*-----------------------------------------------------------------------
- * EPLD Regs.
- */
-#define EPLD_BASE 0x80000000
-#define EPLD_ETHRSTBOOT 0x10
-#define EPLD_CTRL 0x14
-#define EPLD_MUXOE 0x16
-
-/*
- * State definations
- */
-#define LOAK_INIT 0x494e4954 /* ASCII "INIT" */
-#define LOAK_NONE 0x4e4f4e45 /* ASCII "NONE" */
-#define LOAK_CRAM 0x4352414d /* ASCII "CRAM" */
-#define LOAK_PSRAM 0x50535241 /* ASCII "PSRA" - PSRAM */
-#define LOAK_OCM 0x4f434d20 /* ASCII "OCM " */
-#define LOAK_ZERO 0x5a45524f /* ASCII "ZERO" */
-#define LOAK_SPL 0x53504c20 /* ASCII "SPL" */
-
/*
* Internal Definitions
*
diff --git a/include/configs/atstk1002.h b/include/configs/atstk1002.h
index 458ebab..beaf385 100644
--- a/include/configs/atstk1002.h
+++ b/include/configs/atstk1002.h
@@ -62,11 +62,14 @@
*/
#define CFG_PLL0_OPT 0x04
-#define CFG_USART1 1
-
-#define CFG_CONSOLE_UART_DEV DEVICE_USART1
+#undef CONFIG_USART0
+#define CONFIG_USART1 1
+#undef CONFIG_USART2
+#undef CONFIG_USART3
/* User serviceable stuff */
+#define CONFIG_DOS_PARTITION 1
+
#define CONFIG_CMDLINE_TAG 1
#define CONFIG_SETUP_MEMORY_TAGS 1
#define CONFIG_INITRD_TAG 1
@@ -75,16 +78,47 @@
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTARGS \
- "console=ttyUS0 root=/dev/mtdblock1 fbmem=600k"
+ "console=ttyS0 root=/dev/mtdblock1 rootfstype=jffs2 fbmem=600k"
+
+#define CONFIG_BOOTCOMMAND \
+ "fsload; bootm $(fileaddr)"
+
+/*
+ * Only interrupt autoboot if <space> is pressed. Otherwise, garbage
+ * data on the serial line may interrupt the boot sequence.
+ */
+#define CONFIG_BOOTDELAY 2
+#define CONFIG_AUTOBOOT 1
+#define CONFIG_AUTOBOOT_KEYED 1
+#define CONFIG_AUTOBOOT_PROMPT \
+ "Press SPACE to abort autoboot in %d seconds\n"
+#define CONFIG_AUTOBOOT_DELAY_STR "d"
+#define CONFIG_AUTOBOOT_STOP_STR " "
+
+/*
+ * These are "locally administered ethernet addresses" generated by
+ * ./tools/gen_eth_addr
+ *
+ * After booting the board for the first time, new addresses should be
+ * generated and assigned to the environment variables "ethaddr" and
+ * "eth1addr".
+ */
+#define CONFIG_ETHADDR "6a:87:71:14:cd:cb"
+#define CONFIG_ETH1ADDR "ca:f8:15:e6:3e:e6"
+#define CONFIG_OVERWRITE_ETHADDR_ONCE 1
+#define CONFIG_NET_MULTI 1
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_SUBNETMASK \
+ | CONFIG_BOOTP_GATEWAY)
#define CONFIG_COMMANDS (CFG_CMD_BDI \
| CFG_CMD_LOADS \
| CFG_CMD_LOADB \
- /* | CFG_CMD_IMI */ \
+ | CFG_CMD_IMI \
/* | CFG_CMD_CACHE */ \
| CFG_CMD_FLASH \
| CFG_CMD_MEMORY \
- /* | CFG_CMD_NET */ \
+ | CFG_CMD_NET \
| CFG_CMD_ENV \
/* | CFG_CMD_IRQ */ \
| CFG_CMD_BOOTD \
@@ -96,7 +130,7 @@
/* | CFG_CMD_I2C */ \
| CFG_CMD_REGINFO \
/* | CFG_CMD_DATE */ \
- /* | CFG_CMD_DHCP */ \
+ | CFG_CMD_DHCP \
/* | CFG_CMD_AUTOSCRIPT */ \
/* | CFG_CMD_MII */ \
| CFG_CMD_MISC \
@@ -106,19 +140,22 @@
/* | CFG_CMD_SAVES */ \
/* | CFG_CMD_SPI */ \
/* | CFG_CMD_PING */ \
- /* | CFG_CMD_MMC */ \
- /* | CFG_CMD_FAT */ \
- /* | CFG_CMD_IMLS */ \
+ | CFG_CMD_MMC \
+ | CFG_CMD_FAT \
+ | CFG_CMD_IMLS \
/* | CFG_CMD_ITEST */ \
- /* | CFG_CMD_EXT2 */ \
+ | CFG_CMD_EXT2 \
+ | CFG_CMD_JFFS2 \
)
#include <cmd_confdefs.h>
#define CONFIG_ATMEL_USART 1
+#define CONFIG_MACB 1
#define CONFIG_PIO2 1
#define CFG_NR_PIOS 5
#define CFG_HSDRAMC 1
+#define CONFIG_MMC 1
#define CFG_DCACHE_LINESZ 32
#define CFG_ICACHE_LINESZ 32
@@ -150,16 +187,8 @@
#define CFG_INIT_SP_ADDR (CFG_INTRAM_BASE + CFG_INTRAM_SIZE)
#define CFG_MALLOC_LEN (256*1024)
-#define CFG_MALLOC_END \
- ({ \
- DECLARE_GLOBAL_DATA_PTR; \
- CFG_SDRAM_BASE + gd->sdram_size; \
- })
-#define CFG_MALLOC_START (CFG_MALLOC_END - CFG_MALLOC_LEN)
-
#define CFG_DMA_ALLOC_LEN (16384)
-#define CFG_DMA_ALLOC_END (CFG_MALLOC_START)
-#define CFG_DMA_ALLOC_START (CFG_DMA_ALLOC_END - CFG_DMA_ALLOC_LEN)
+
/* Allow 2MB for the kernel run-time image */
#define CFG_LOAD_ADDR (CFG_SDRAM_BASE + 0x00200000)
#define CFG_BOOTPARAMS_LEN (16 * 1024)
diff --git a/include/configs/katmai.h b/include/configs/katmai.h
index 1606d0d..7f55366 100644
--- a/include/configs/katmai.h
+++ b/include/configs/katmai.h
@@ -78,7 +78,7 @@
#define CONFIG_PCI_SYS_MEM_PHYS CFG_SDRAM_BASE
#define CONFIG_PCI_SYS_MEM_SIZE (1024 * 1024 * 1024)
-#define CFG_ACE_BASE 0xe0000000 /* Xilinx ACE controller - Compact Flash */
+#define CFG_ACE_BASE 0xfe000000 /* Xilinx ACE controller - Compact Flash */
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer (placed in internal SRAM)
diff --git a/include/configs/ml401.h b/include/configs/ml401.h
new file mode 100644
index 0000000..cb159e7
--- /dev/null
+++ b/include/configs/ml401.h
@@ -0,0 +1,230 @@
+/*
+ * (C) Copyright 2007 Czech Technical University.
+ *
+ * Michal SIMEK <monstr@seznam.cz>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include "../board/xilinx/ml401/xparameters.h"
+
+#define CONFIG_MICROBLAZE 1 /* MicroBlaze CPU */
+#define CONFIG_ML401 1 /* ML401 Board */
+
+/* uart */
+#define CONFIG_SERIAL_BASE XILINX_UART_BASEADDR
+#define CONFIG_BAUDRATE XILINX_UART_BAUDRATE
+#define CFG_BAUDRATE_TABLE { CONFIG_BAUDRATE }
+
+/* setting reset address */
+#define CFG_RESET_ADDRESS TEXT_BASE
+
+/* ethernet */
+#define CONFIG_EMACLITE 1
+#define XPAR_EMAC_0_DEVICE_ID XPAR_XEMAC_NUM_INSTANCES
+
+/* gpio */
+#define CFG_GPIO_0 1
+#define CFG_GPIO_0_ADDR XILINX_GPIO_BASEADDR
+
+/* interrupt controller */
+#define CFG_INTC_0 1
+#define CFG_INTC_0_ADDR XILINX_INTC_BASEADDR
+#define CFG_INTC_0_NUM XILINX_INTC_NUM_INTR_INPUTS
+
+/* timer */
+#define CFG_TIMER_0 1
+#define CFG_TIMER_0_ADDR XILINX_TIMER_BASEADDR
+#define CFG_TIMER_0_IRQ XILINX_TIMER_IRQ
+#define FREQUENCE XILINX_CLOCK_FREQ
+#define CFG_TIMER_0_PRELOAD ( FREQUENCE/1000 )
+
+/*
+ * memory layout - Example
+ * TEXT_BASE = 0x1200_0000;
+ * CFG_SRAM_BASE = 0x1000_0000;
+ * CFG_SRAM_SIZE = 0x0400_0000;
+ *
+ * CFG_GBL_DATA_OFFSET = 0x1000_0000 + 0x0400_0000 - 0x1000 = 0x13FF_F000
+ * CFG_MONITOR_BASE = 0x13FF_F000 - 0x40000 = 0x13FB_F000
+ * CFG_MALLOC_BASE = 0x13FB_F000 - 0x40000 = 0x13F7_F000
+ *
+ * 0x1000_0000 CFG_SDRAM_BASE
+ * FREE
+ * 0x1200_0000 TEXT_BASE
+ * U-BOOT code
+ * 0x1202_0000
+ * FREE
+ *
+ * STACK
+ * 0x13F7_F000 CFG_MALLOC_BASE
+ * MALLOC_AREA 256kB Alloc
+ * 0x11FB_F000 CFG_MONITOR_BASE
+ * MONITOR_CODE 256kB Env
+ * 0x13FF_F000 CFG_GBL_DATA_OFFSET
+ * GLOBAL_DATA 4kB bd, gd
+ * 0x1400_0000 CFG_SDRAM_BASE + CFG_SDRAM_SIZE
+ */
+
+/* ddr sdram - main memory */
+#define CFG_SDRAM_BASE XILINX_RAM_START
+#define CFG_SDRAM_SIZE XILINX_RAM_SIZE
+#define CFG_MEMTEST_START CFG_SDRAM_BASE
+#define CFG_MEMTEST_END (CFG_SDRAM_BASE + 0x1000)
+
+/* global pointer */
+#define CFG_GBL_DATA_SIZE 0x1000 /* size of global data */
+#define CFG_GBL_DATA_OFFSET (CFG_SDRAM_BASE + CFG_SDRAM_SIZE - CFG_GBL_DATA_SIZE) /* start of global data */
+
+/* monitor code */
+#define SIZE 0x40000
+#define CFG_MONITOR_LEN SIZE
+#define CFG_MONITOR_BASE (CFG_GBL_DATA_OFFSET - CFG_MONITOR_LEN)
+#define CFG_MONITOR_END (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
+#define CFG_MALLOC_LEN SIZE
+#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN)
+
+/* stack */
+#define CFG_INIT_SP_OFFSET CFG_MONITOR_BASE
+
+/*#define RAMENV */
+#define FLASH
+
+#ifdef FLASH
+ #define CFG_FLASH_BASE XILINX_FLASH_START
+ #define CFG_FLASH_SIZE XILINX_FLASH_SIZE
+ #define CFG_FLASH_CFI 1
+ #define CFG_FLASH_CFI_DRIVER 1
+ #define CFG_FLASH_EMPTY_INFO 1 /* ?empty sector */
+ #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+ #define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
+
+ #ifdef RAMENV
+ #define CFG_ENV_IS_NOWHERE 1
+ #define CFG_ENV_SIZE 0x1000
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SIZE)
+
+ #else /* !RAMENV */
+ #define CFG_ENV_IS_IN_FLASH 1
+ #define CFG_ENV_ADDR 0x40000
+ #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
+ #define CFG_ENV_SIZE 0x2000
+ #endif /* !RAMBOOT */
+#else /* !FLASH */
+ /* ENV in RAM */
+ #define CFG_NO_FLASH 1
+ #define CFG_ENV_IS_NOWHERE 1
+ #define CFG_ENV_SIZE 0x1000
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SIZE)
+#endif /* !FLASH */
+
+#ifdef FLASH
+ #ifdef RAMENV
+ #define CONFIG_COMMANDS (CONFIG__CMD_DFL |\
+ CFG_CMD_MEMORY |\
+ CFG_CMD_MISC |\
+ CFG_CMD_AUTOSCRIPT |\
+ CFG_CMD_IRQ |\
+ CFG_CMD_ASKENV |\
+ CFG_CMD_BDI |\
+ CFG_CMD_RUN |\
+ CFG_CMD_LOADS |\
+ CFG_CMD_LOADB |\
+ CFG_CMD_IMI |\
+ CFG_CMD_NET |\
+ CFG_CMD_CACHE |\
+ CFG_CMD_IMLS |\
+ CFG_CMD_FLASH |\
+ CFG_CMD_PING \
+ )
+ #else /* !RAMENV */
+ #define CONFIG_COMMANDS (CONFIG__CMD_DFL |\
+ CFG_CMD_MEMORY |\
+ CFG_CMD_MISC |\
+ CFG_CMD_AUTOSCRIPT |\
+ CFG_CMD_IRQ |\
+ CFG_CMD_ASKENV |\
+ CFG_CMD_BDI |\
+ CFG_CMD_RUN |\
+ CFG_CMD_LOADS |\
+ CFG_CMD_LOADB |\
+ CFG_CMD_IMI |\
+ CFG_CMD_NET |\
+ CFG_CMD_CACHE |\
+ CFG_CMD_IMLS |\
+ CFG_CMD_FLASH |\
+ CFG_CMD_PING |\
+ CFG_CMD_ENV |\
+ CFG_CMD_SAVES \
+ )
+
+ #endif
+
+#else /* !FLASH */
+ #define CONFIG_COMMANDS (CONFIG__CMD_DFL |\
+ CFG_CMD_MEMORY |\
+ CFG_CMD_MISC |\
+ CFG_CMD_AUTOSCRIPT |\
+ CFG_CMD_IRQ |\
+ CFG_CMD_ASKENV |\
+ CFG_CMD_BDI |\
+ CFG_CMD_RUN |\
+ CFG_CMD_LOADS |\
+ CFG_CMD_LOADB |\
+ CFG_CMD_IMI |\
+ CFG_CMD_NET |\
+ CFG_CMD_CACHE |\
+ CFG_CMD_PING \
+ )
+#endif /* !FLASH */
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/* Miscellaneous configurable options */
+#define CFG_PROMPT "U-Boot-mONStR> "
+#define CFG_CBSIZE 512 /* size of console buffer */
+#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) /* print buffer size */
+#define CFG_MAXARGS 15 /* max number of command args */
+#define CFG_LONGHELP
+#define CFG_LOAD_ADDR 0x12000000 /* default load address */
+
+#define CONFIG_BOOTDELAY 30
+#define CONFIG_BOOTARGS "root=romfs"
+#define CONFIG_HOSTNAME "ml401"
+#define CONFIG_BOOTCOMMAND "base 0;tftp 11000000 image.img;bootm"
+#define CONFIG_IPADDR 192.168.0.3
+#define CONFIG_SERVERIP 192.168.0.5
+#define CONFIG_GATEWAYIP 192.168.0.1
+#define CONFIG_ETHADDR 00:E0:0C:00:00:FD
+
+/* architecture dependent code */
+#define CFG_USR_EXCEP /* user exception */
+#define CFG_HZ 1000
+
+/* system ace */
+/*#define CONFIG_SYSTEMACE
+#define DEBUG_SYSTEMACE
+#define CFG_SYSTEMACE_BASE XILINX_SYSACE_BASEADDR
+#define CFG_SYSTEMACE_WIDTH XILINX_SYSACE_MEM_WIDTH
+#define CONFIG_DOS_PARTITION
+*/
+#endif /* __CONFIG_H */
diff --git a/include/configs/mpc7448hpc2.h b/include/configs/mpc7448hpc2.h
new file mode 100644
index 0000000..243a3f6
--- /dev/null
+++ b/include/configs/mpc7448hpc2.h
@@ -0,0 +1,411 @@
+/*
+ * Copyright (c) 2005 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2006
+ * Alex Bounine , Tundra Semiconductor Corp.
+ * Roy Zang , <tie-fei.zang@freescale.com> Freescale Corp.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board specific configuration options for Freescale
+ * MPC7448HPC2 (High-Performance Computing II) (Taiga) board
+ *
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#undef DEBUG
+
+/* Board Configuration Definitions */
+/* MPC7448HPC2 (High-Performance Computing II) (Taiga) board */
+
+#define CONFIG_MPC7448HPC2
+
+#define CONFIG_74xx
+#define CONFIG_750FX /* this option to enable init of extended BATs */
+#define CONFIG_ALTIVEC /* undef to disable */
+
+#define CFG_BOARD_NAME "MPC7448 HPC II"
+#define CONFIG_IDENT_STRING " Freescale MPC7448 HPC II"
+
+#define CFG_OCN_CLK 133000000 /* 133 MHz */
+#define CFG_CONFIG_BUS_CLK 133000000
+
+#define CFG_CLK_SPREAD /* Enable Spread-Spectrum Clock generation */
+
+#undef CONFIG_ECC /* disable ECC support */
+
+/* Board-specific Initialization Functions to be called */
+#define CFG_BOARD_ASM_INIT
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_EARLY_INIT_R
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_HAS_ETH1
+
+#define CONFIG_ENV_OVERWRITE
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_BAUDRATE 115200 /* console baudrate = 115000 */
+
+/*#define CFG_HUSH_PARSER */
+#undef CFG_HUSH_PARSER
+
+#define CFG_PROMPT_HUSH_PS2 "> "
+
+/* Pass open firmware flat tree */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+
+#define OF_CPU "PowerPC,7448@0"
+#define OF_TSI "tsi108@c0000000"
+#define OF_TBCLK (bd->bi_busfreq / 8)
+#define OF_STDOUT_PATH "/tsi108@c0000000/serial@7808"
+
+/*
+ * The following defines let you select what serial you want to use
+ * for your console driver.
+ *
+ * what to do:
+ * If you have hacked a serial cable onto the second DUART channel,
+ * change the CFG_DUART port from 1 to 0 below.
+ *
+ */
+
+#define CONFIG_CONS_INDEX 1
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE 1
+#define CFG_NS16550_CLK CFG_OCN_CLK * 8
+
+#define CFG_NS16550_COM1 (CFG_TSI108_CSR_RST_BASE+0x7808)
+#define CFG_NS16550_COM2 (CFG_TSI108_CSR_RST_BASE+0x7C08)
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+
+#undef CONFIG_BOOTARGS
+/* #define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\"
+ * to mount root filesystem over NFS;echo" */
+
+#if (CONFIG_BOOTDELAY >= 0)
+#define CONFIG_BOOTCOMMAND "tftpboot 0x400000 zImage.initrd.elf;\
+ setenv bootargs $(bootargs) $(bootargs_root) nfsroot=$(serverip):$(rootpath) \
+ ip=$(ipaddr):$(serverip)$(bootargs_end); bootm 0x400000; "
+
+#define CONFIG_BOOTARGS "console=ttyS0,115200"
+#endif
+
+#undef CONFIG_EXTRA_ENV_SETTINGS
+
+#define CONFIG_SERIAL "No. 1"
+
+/* Networking Configuration */
+
+#define KSEG1ADDR(a) (a) /* Needed by the rtl8139 driver */
+
+#define CONFIG_TSI108_ETH
+#define CONFIG_TSI108_ETH_NUM_PORTS 2
+
+#define CONFIG_NET_MULTI
+
+#define CONFIG_BOOTFILE zImage.initrd.elf
+#define CONFIG_LOADADDR 0x400000
+
+/*-------------------------------------------------------------------------- */
+
+#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */
+#define CFG_LOADS_BAUD_CHANGE /* allow baudrate changes */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
+ CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
+ | CFG_CMD_ASKENV \
+ | CFG_CMD_CACHE \
+ | CFG_CMD_PCI \
+ | CFG_CMD_I2C \
+ | CFG_CMD_SDRAM \
+ | CFG_CMD_EEPROM \
+ | CFG_CMD_FLASH \
+ | CFG_CMD_ENV \
+ | CFG_CMD_BSP \
+ | CFG_CMD_DHCP \
+ | CFG_CMD_PING \
+ | CFG_CMD_DATE)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*set date in u-boot*/
+#define CONFIG_RTC_M48T35A
+#define CFG_NVRAM_BASE_ADDR 0xfc000000
+#define CFG_NVRAM_SIZE 0x8000
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_VERSION_VARIABLE 1
+#define CONFIG_TSI108_I2C
+
+#define CFG_I2C_EEPROM_ADDR 0x50 /* I2C EEPROM page 1 */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16)/* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x00400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x07c00000 /* 4 ... 124 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x00400000 /* default load address */
+
+#define CFG_HZ 1000 /* decr freq: 1ms ticks */
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area
+ */
+
+/*
+ * When locking data in cache you should point the CFG_INIT_RAM_ADDRESS
+ * To an unused memory region. The stack will remain in cache until RAM
+ * is initialized
+ */
+#undef CFG_INIT_RAM_LOCK
+#define CFG_INIT_RAM_ADDR 0x07d00000 /* unused memory region */
+#define CFG_INIT_RAM_END 0x4000/* larger space - we have SDRAM initialized */
+
+#define CFG_GBL_DATA_SIZE 128/* size in bytes reserved for init data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+
+#define CFG_SDRAM_BASE 0x00000000 /* first 256 MB of SDRAM */
+#define CFG_SDRAM1_BASE 0x10000000 /* next 256MB of SDRAM */
+
+#define CFG_SDRAM2_BASE 0x40000000 /* beginning of non-cacheable alias for SDRAM - first 256MB */
+#define CFG_SDRAM3_BASE 0x50000000 /* next Non-Cacheable 256MB of SDRAM */
+
+#define CFG_PCI_PFM_BASE 0x80000000 /* Prefetchable (cacheable) PCI/X PFM and SDRAM OCN (128MB+128MB) */
+
+#define CFG_PCI_MEM32_BASE 0xE0000000 /* Non-Cacheable PCI/X MEM and SDRAM OCN (128MB+128MB) */
+
+#define CFG_MISC_REGION_BASE 0xf0000000 /* Base Address for (PCI/X + Flash) region */
+
+#define CFG_FLASH_BASE 0xff000000 /* Base Address of Flash device */
+#define CFG_FLASH_BASE2 0xfe000000 /* Alternate Flash Base Address */
+
+#define CONFIG_VERY_BIG_RAM /* we will use up to 256M memory for cause we are short of BATS */
+
+#define PCI0_IO_BASE_BOOTM 0xfd000000
+
+#define CFG_RESET_ADDRESS 0x3fffff00
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CFG_MONITOR_BASE TEXT_BASE /* u-boot code base */
+#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc */
+
+/* Peripheral Device section */
+
+/*
+ * Resources on the Tsi108
+ */
+
+#define CFG_TSI108_CSR_RST_BASE 0xC0000000 /* Tsi108 CSR base after reset */
+#define CFG_TSI108_CSR_BASE CFG_TSI108_CSR_RST_BASE /* Runtime Tsi108 CSR base */
+
+#define ENABLE_PCI_CSR_BAR /* enables access to Tsi108 CSRs from the PCI/X bus */
+
+#undef DISABLE_PBM
+
+/*
+ * PCI stuff
+ *
+ */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_TSI108_PCI /* include tsi108 pci support */
+
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+/* PCI MEMORY MAP section */
+
+/* PCI view of System Memory */
+#define CFG_PCI_MEMORY_BUS 0x00000000
+#define CFG_PCI_MEMORY_PHYS 0x00000000
+#define CFG_PCI_MEMORY_SIZE 0x80000000
+
+/* PCI Memory Space */
+#define CFG_PCI_MEM_BUS (CFG_PCI_MEM_PHYS)
+#define CFG_PCI_MEM_PHYS (CFG_PCI_MEM32_BASE) /* 0xE0000000 */
+#define CFG_PCI_MEM_SIZE 0x10000000 /* 256 MB space for PCI/X Mem + SDRAM OCN */
+
+/* PCI I/O Space */
+#define CFG_PCI_IO_BUS 0x00000000
+#define CFG_PCI_IO_PHYS 0xfa000000 /* Changed from fd000000 */
+
+#define CFG_PCI_IO_SIZE 0x01000000 /* 16MB */
+
+#define _IO_BASE 0x00000000 /* points to PCI I/O space */
+
+/* PCI Config Space mapping */
+#define CFG_PCI_CFG_BASE 0xfb000000 /* Changed from FE000000 */
+#define CFG_PCI_CFG_SIZE 0x01000000 /* 16MB */
+
+#define CFG_IBAT0U 0xFE0003FF
+#define CFG_IBAT0L 0xFE000002
+
+#define CFG_IBAT1U 0x00007FFF
+#define CFG_IBAT1L 0x00000012
+
+#define CFG_IBAT2U 0x80007FFF
+#define CFG_IBAT2L 0x80000022
+
+#define CFG_IBAT3U 0x00000000
+#define CFG_IBAT3L 0x00000000
+
+#define CFG_IBAT4U 0x00000000
+#define CFG_IBAT4L 0x00000000
+
+#define CFG_IBAT5U 0x00000000
+#define CFG_IBAT5L 0x00000000
+
+#define CFG_IBAT6U 0x00000000
+#define CFG_IBAT6L 0x00000000
+
+#define CFG_IBAT7U 0x00000000
+#define CFG_IBAT7L 0x00000000
+
+#define CFG_DBAT0U 0xE0003FFF
+#define CFG_DBAT0L 0xE000002A
+
+#define CFG_DBAT1U 0x00007FFF
+#define CFG_DBAT1L 0x00000012
+
+#define CFG_DBAT2U 0x00000000
+#define CFG_DBAT2L 0x00000000
+
+#define CFG_DBAT3U 0xC0000003
+#define CFG_DBAT3L 0xC000002A
+
+#define CFG_DBAT4U 0x00000000
+#define CFG_DBAT4L 0x00000000
+
+#define CFG_DBAT5U 0x00000000
+#define CFG_DBAT5L 0x00000000
+
+#define CFG_DBAT6U 0x00000000
+#define CFG_DBAT6L 0x00000000
+
+#define CFG_DBAT7U 0x00000000
+#define CFG_DBAT7L 0x00000000
+
+/* I2C addresses for the two DIMM SPD chips */
+#define DIMM0_I2C_ADDR 0x51
+#define DIMM1_I2C_ADDR 0x52
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8<<20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 1/* Flash can be at one of two addresses */
+#define FLASH_BANK_SIZE 0x01000000 /* 16 MB Total */
+#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2}
+
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_WRITE_SWAPPED_DATA
+
+#define PHYS_FLASH_SIZE 0x01000000
+#define CFG_MAX_FLASH_SECT (128)
+
+#define CFG_ENV_IS_IN_NVRAM
+#define CFG_ENV_ADDR 0xFC000000
+
+#define CFG_ENV_OFFSET 0x00000000 /* Offset of Environment Sector */
+#define CFG_ENV_SIZE 0x00000400 /* Total Size of Environment Space */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * L2CR setup -- make sure this is right for your board!
+ * look in include/mpc74xx.h for the defines used here
+ */
+#undef CFG_L2
+
+#define L2_INIT 0
+#define L2_ENABLE (L2_INIT | L2CR_L2E)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+#define CFG_SERIAL_HANG_IN_EXCEPTION
+#endif /* __CONFIG_H */
diff --git a/include/configs/sc3.h b/include/configs/sc3.h
index 8298084..6b6acfa 100644
--- a/include/configs/sc3.h
+++ b/include/configs/sc3.h
@@ -133,8 +133,8 @@
#if 1 /* feel free to disable for development */
#define CONFIG_AUTOBOOT_KEYED /* Enable password protection */
-#define CONFIG_AUTOBOOT_PROMPT "\nSC3 - booting... stop with S\n"
-#define CONFIG_AUTOBOOT_DELAY_STR "S" /* 1st "password" */
+#define CONFIG_AUTOBOOT_PROMPT "\nSC3 - booting... stop with ENTER\n"
+#define CONFIG_AUTOBOOT_DELAY_STR "\n" /* 1st "password" */
#endif
/*
@@ -416,11 +416,11 @@
#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */
-/* No command line, one static partition Partition 3 contains jffs2 rootfs */
+/* No command line, one static partition */
#undef CONFIG_JFFS2_CMDLINE
#define CONFIG_JFFS2_DEV "nand0"
-#define CONFIG_JFFS2_PART_SIZE 0x00400000
-#define CONFIG_JFFS2_PART_OFFSET 0x00c00000
+#define CONFIG_JFFS2_PART_SIZE 0x01000000
+#define CONFIG_JFFS2_PART_OFFSET 0x00000000
/*-----------------------------------------------------------------------
* Cache Configuration
diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h
index 29f3b40..1f19621 100644
--- a/include/configs/sequoia.h
+++ b/include/configs/sequoia.h
@@ -33,7 +33,6 @@
*----------------------------------------------------------------------*/
/* This config file is used for Sequoia (440EPx) and Rainier (440GRx) */
#ifndef CONFIG_RAINIER
-#define CONFIG_SEQUOIA 1 /* Board is Sequoia */
#define CONFIG_440EPX 1 /* Specific PPC440EPx */
#else
#define CONFIG_440GRX 1 /* Specific PPC440GRx */
@@ -75,9 +74,7 @@
* Initial RAM & stack pointer
*----------------------------------------------------------------------*/
/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */
-#define CFG_INIT_RAM_OCM 1 /* OCM as init ram */
#define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */
-
#define CFG_INIT_RAM_END (4 << 10)
#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
@@ -381,9 +378,6 @@
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
-#define CFG_FLASH CFG_FLASH_BASE
-#define CFG_NAND 0xD0000000
-#define CFG_CPLD 0xC0000000
/*
* On Sequoia CS0 and CS3 are switched when configuring for NAND booting
@@ -392,25 +386,25 @@
#define CFG_NAND_CS 3 /* NAND chip connected to CSx */
/* Memory Bank 0 (NOR-FLASH) initialization */
#define CFG_EBC_PB0AP 0x03017200
-#define CFG_EBC_PB0CR (CFG_FLASH | 0xda000)
+#define CFG_EBC_PB0CR (CFG_FLASH_BASE | 0xda000)
/* Memory Bank 3 (NAND-FLASH) initialization */
#define CFG_EBC_PB3AP 0x018003c0
-#define CFG_EBC_PB3CR (CFG_NAND | 0x1c000)
+#define CFG_EBC_PB3CR (CFG_NAND_ADDR | 0x1c000)
#else
#define CFG_NAND_CS 0 /* NAND chip connected to CSx */
/* Memory Bank 3 (NOR-FLASH) initialization */
#define CFG_EBC_PB3AP 0x03017200
-#define CFG_EBC_PB3CR (CFG_FLASH | 0xda000)
+#define CFG_EBC_PB3CR (CFG_FLASH_BASE | 0xda000)
/* Memory Bank 0 (NAND-FLASH) initialization */
#define CFG_EBC_PB0AP 0x018003c0
-#define CFG_EBC_PB0CR (CFG_NAND | 0x1c000)
+#define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1c000)
#endif
/* Memory Bank 2 (CPLD) initialization */
#define CFG_EBC_PB2AP 0x24814580
-#define CFG_EBC_PB2CR (CFG_CPLD | 0x38000)
+#define CFG_EBC_PB2CR (CFG_BCSR_BASE | 0x38000)
/*-----------------------------------------------------------------------
* NAND FLASH
diff --git a/include/configs/suzaku.h b/include/configs/suzaku.h
index 1ee6be1..8224555 100644
--- a/include/configs/suzaku.h
+++ b/include/configs/suzaku.h
@@ -44,12 +44,17 @@
#define CFG_FLASH_SIZE 0x00400000
#define CFG_RESET_ADDRESS 0xfff00100
#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CFG_MONITOR_BASE (CFG_SDRAM_BASE + CFG_SDRAM_SIZE - (1024 * 1024))
+#define CFG_MONITOR_BASE (CFG_SDRAM_BASE + CFG_SDRAM_SIZE - (1024 * 1024))
#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc */
+#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - (1024 * 1024))
#define CONFIG_BAUDRATE 115200
#define CFG_BAUDRATE_TABLE { 115200 }
+/* System Register (GPIO) */
+#define MICROBLAZE_SYSREG_BASE_ADDR 0xFFFFA000
+#define MICROBLAZE_SYSREG_RECONFIGURE (1 << 0)
+
#define CONFIG_COMMANDS (CONFIG__CMD_DFL)
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
diff --git a/include/configs/xupv2p.h b/include/configs/xupv2p.h
new file mode 100644
index 0000000..a2f4810
--- /dev/null
+++ b/include/configs/xupv2p.h
@@ -0,0 +1,174 @@
+/*
+ * (C) Copyright 2007 Czech Technical University.
+ *
+ * Michal SIMEK <monstr@monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include "../board/xilinx/xupv2p/xparameters.h"
+
+#define CONFIG_MICROBLAZE 1 /* MicroBlaze CPU */
+#define CONFIG_XUPV2P 1
+
+/* uart */
+#define CONFIG_SERIAL_BASE XILINX_UART_BASEADDR
+#define CONFIG_BAUDRATE XILINX_UART_BAUDRATE
+#define CFG_BAUDRATE_TABLE { CONFIG_BAUDRATE }
+
+/* ethernet */
+#define CONFIG_EMAC 1
+#define XPAR_EMAC_0_DEVICE_ID XPAR_XEMAC_NUM_INSTANCES
+
+/*
+ * setting reset address
+ *
+ * TEXT_BASE is set to place, where the U-BOOT run in RAM, but
+ * if you want to store U-BOOT in flash, set CFG_RESET_ADDRESS
+ * to FLASH memory and after loading bitstream jump to FLASH.
+ * U-BOOT auto-relocate to TEXT_BASE. After RESET command Microblaze
+ * jump to CFG_RESET_ADDRESS where is the original U-BOOT code.
+ */
+#define CFG_RESET_ADDRESS 0x36000000
+
+/* gpio */
+#define CFG_GPIO_0 1
+#define CFG_GPIO_0_ADDR XILINX_GPIO_BASEADDR
+
+/* interrupt controller */
+#define CFG_INTC_0 1
+#define CFG_INTC_0_ADDR XILINX_INTC_BASEADDR
+#define CFG_INTC_0_NUM XILINX_INTC_NUM_INTR_INPUTS
+
+/* timer */
+#define CFG_TIMER_0 1
+#define CFG_TIMER_0_ADDR XILINX_TIMER_BASEADDR
+#define CFG_TIMER_0_IRQ XILINX_TIMER_IRQ
+#define FREQUENCE XILINX_CLOCK_FREQ
+#define CFG_TIMER_0_PRELOAD ( FREQUENCE/1000 )
+
+/*
+ * memory layout - Example
+ * TEXT_BASE = 0x3600_0000;
+ * CFG_SRAM_BASE = 0x3000_0000;
+ * CFG_SRAM_SIZE = 0x1000_0000;
+ *
+ * CFG_GBL_DATA_OFFSET = 0x3000_0000 + 0x1000_0000 - 0x1000 = 0x3FFF_F000
+ * CFG_MONITOR_BASE = 0x3FFF_F000 - 0x40000 = 0x3FFB_F000
+ * CFG_MALLOC_BASE = 0x3FFB_F000 - 0x40000 = 0x3FF7_F000
+ *
+ * 0x3000_0000 CFG_SDRAM_BASE
+ * FREE
+ * 0x3600_0000 TEXT_BASE
+ * U-BOOT code
+ * 0x3602_0000
+ * FREE
+ *
+ * STACK
+ * 0x3FF7_F000 CFG_MALLOC_BASE
+ * MALLOC_AREA 256kB Alloc
+ * 0x3FFB_F000 CFG_MONITOR_BASE
+ * MONITOR_CODE 256kB Env
+ * 0x3FFF_F000 CFG_GBL_DATA_OFFSET
+ * GLOBAL_DATA 4kB bd, gd
+ * 0x4000_0000 CFG_SDRAM_BASE + CFG_SDRAM_SIZE
+ */
+
+/* ddr sdram - main memory */
+#define CFG_SDRAM_BASE XILINX_RAM_START
+#define CFG_SDRAM_SIZE XILINX_RAM_SIZE
+#define CFG_MEMTEST_START CFG_SDRAM_BASE
+#define CFG_MEMTEST_END (CFG_SDRAM_BASE + 0x1000)
+
+/* global pointer */
+#define CFG_GBL_DATA_SIZE 0x1000 /* size of global data */
+#define CFG_GBL_DATA_OFFSET (CFG_SDRAM_BASE + CFG_SDRAM_SIZE - CFG_GBL_DATA_SIZE) /* start of global data */
+
+/* monitor code */
+#define SIZE 0x40000
+#define CFG_MONITOR_LEN SIZE
+#define CFG_MONITOR_BASE (CFG_GBL_DATA_OFFSET - CFG_MONITOR_LEN)
+#define CFG_MONITOR_END (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
+#define CFG_MALLOC_LEN SIZE
+#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN)
+
+/* stack */
+#define CFG_INIT_SP_OFFSET CFG_MALLOC_BASE
+
+#define CFG_NO_FLASH 1
+#define CFG_ENV_IS_NOWHERE 1
+#define CFG_ENV_SIZE 0x1000
+#define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SIZE)
+#define CONFIG_COMMANDS (CONFIG__CMD_DFL |\
+ CFG_CMD_MEMORY |\
+ CFG_CMD_IRQ |\
+ CFG_CMD_BDI |\
+ CFG_CMD_NET |\
+ CFG_CMD_IMI |\
+ CFG_CMD_ECHO |\
+ CFG_CMD_CACHE |\
+ CFG_CMD_RUN |\
+ CFG_CMD_AUTOSCRIPT |\
+ CFG_CMD_ASKENV |\
+ CFG_CMD_LOADS |\
+ CFG_CMD_LOADB |\
+ CFG_CMD_MISC |\
+ CFG_CMD_PING \
+ )
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/* Miscellaneous configurable options */
+#define CFG_PROMPT "U-Boot-mONStR> "
+#define CFG_CBSIZE 512 /* size of console buffer */
+#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) /* print buffer size */
+#define CFG_MAXARGS 15 /* max number of command args */
+#define CFG_LONGHELP
+#define CFG_LOAD_ADDR 0x12000000 /* default load address */
+
+#define CONFIG_BOOTDELAY 30
+#define CONFIG_BOOTARGS "root=romfs"
+#define CONFIG_HOSTNAME "ml401"
+#define CONFIG_BOOTCOMMAND "base 0;tftp 11000000 image.img;bootm"
+#define CONFIG_IPADDR 192.168.0.3
+#define CONFIG_SERVERIP 192.168.0.5
+#define CONFIG_GATEWAYIP 192.168.0.1
+#define CONFIG_ETHADDR 00:E0:0C:00:00:FD
+
+/* architecture dependent code */
+#define CFG_USR_EXCEP /* user exception */
+#define CFG_HZ 1000
+
+#define CONFIG_PREBOOT "echo U-BOOT by mONStR;" \
+ "base 0;" \
+ "echo"
+
+
+/* system ace */
+/*#define CONFIG_SYSTEMACE
+#define DEBUG_SYSTEMACE
+#define CFG_SYSTEMACE_BASE 0xCF000000
+#define CFG_SYSTEMACE_WIDTH 16
+#define CONFIG_DOS_PARTITION*/
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h
index 818462e..b68ae54 100644
--- a/include/configs/yosemite.h
+++ b/include/configs/yosemite.h
@@ -32,7 +32,6 @@
*----------------------------------------------------------------------*/
/* This config file is used for Yosemite (440EP) and Yellowstone (440GR)*/
#ifndef CONFIG_YELLOWSTONE
-#define CONFIG_YOSEMITE 1 /* Board is Yosemite */
#define CONFIG_440EP 1 /* Specific PPC440EP support */
#define CONFIG_HOSTNAME yosemite
#else
diff --git a/include/configs/yucca.h b/include/configs/yucca.h
index eb4859c..7f8b022 100644
--- a/include/configs/yucca.h
+++ b/include/configs/yucca.h
@@ -120,7 +120,7 @@
*----------------------------------------------------------------------*/
#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup */
#define SPD_EEPROM_ADDRESS {0x53, 0x52} /* SPD i2c spd addresses*/
-#undef CONFIG_DDR_ECC /* no ECC support for now */
+#define CONFIG_DDR_ECC 1 /* with ECC support */
/*-----------------------------------------------------------------------
* I2C
diff --git a/include/fdt.h b/include/fdt.h
new file mode 100644
index 0000000..48ccfd9
--- /dev/null
+++ b/include/fdt.h
@@ -0,0 +1,60 @@
+#ifndef _FDT_H
+#define _FDT_H
+
+#ifndef __ASSEMBLY__
+
+struct fdt_header {
+ uint32_t magic; /* magic word FDT_MAGIC */
+ uint32_t totalsize; /* total size of DT block */
+ uint32_t off_dt_struct; /* offset to structure */
+ uint32_t off_dt_strings; /* offset to strings */
+ uint32_t off_mem_rsvmap; /* offset to memory reserve map */
+ uint32_t version; /* format version */
+ uint32_t last_comp_version; /* last compatible version */
+
+ /* version 2 fields below */
+ uint32_t boot_cpuid_phys; /* Which physical CPU id we're
+ booting on */
+ /* version 3 fields below */
+ uint32_t size_dt_strings; /* size of the strings block */
+
+ /* version 17 fields below */
+ uint32_t size_dt_struct; /* size of the structure block */
+};
+
+struct fdt_reserve_entry {
+ uint64_t address;
+ uint64_t size;
+};
+
+struct fdt_node_header {
+ uint32_t tag;
+ char name[0];
+};
+
+struct fdt_property {
+ uint32_t tag;
+ uint32_t len;
+ uint32_t nameoff;
+ char data[0];
+};
+
+#endif /* !__ASSEMBLY */
+
+#define FDT_MAGIC 0xd00dfeed /* 4: version, 4: total size */
+#define FDT_TAGSIZE sizeof(uint32_t)
+
+#define FDT_BEGIN_NODE 0x1 /* Start node: full name */
+#define FDT_END_NODE 0x2 /* End node */
+#define FDT_PROP 0x3 /* Property: name off,
+ size, content */
+#define FDT_NOP 0x4 /* nop */
+#define FDT_END 0x9
+
+#define FDT_V1_SIZE (7*sizeof(uint32_t))
+#define FDT_V2_SIZE (FDT_V1_SIZE + sizeof(uint32_t))
+#define FDT_V3_SIZE (FDT_V2_SIZE + sizeof(uint32_t))
+#define FDT_V16_SIZE FDT_V3_SIZE
+#define FDT_V17_SIZE (FDT_V16_SIZE + sizeof(uint32_t))
+
+#endif /* _FDT_H */
diff --git a/include/libfdt.h b/include/libfdt.h
new file mode 100644
index 0000000..a0b4d55
--- /dev/null
+++ b/include/libfdt.h
@@ -0,0 +1,138 @@
+#ifndef _LIBFDT_H
+#define _LIBFDT_H
+/*
+ * libfdt - Flat Device Tree manipulation
+ * Copyright (C) 2006 David Gibson, IBM Corporation.
+ *
+ * This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU Lesser General Public License
+ * as published by the Free Software Foundation; either version 2.1 of
+ * the License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * Lesser General Public License for more details.
+ *
+ * You should have received a copy of the GNU Lesser General Public
+ * License along with this library; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <fdt.h>
+#include <libfdt_env.h>
+
+#define FDT_FIRST_SUPPORTED_VERSION 0x10
+#define FDT_LAST_SUPPORTED_VERSION 0x11
+
+/* Error codes: informative error codes */
+#define FDT_ERR_NOTFOUND 1
+#define FDT_ERR_EXISTS 2
+#define FDT_ERR_NOSPACE 3
+
+/* Error codes: codes for bad parameters */
+#define FDT_ERR_BADOFFSET 4
+#define FDT_ERR_BADPATH 5
+#define FDT_ERR_BADSTATE 6
+
+/* Error codes: codes for bad device tree blobs */
+#define FDT_ERR_TRUNCATED 7
+#define FDT_ERR_BADMAGIC 8
+#define FDT_ERR_BADVERSION 9
+#define FDT_ERR_BADSTRUCTURE 10
+#define FDT_ERR_BADLAYOUT 11
+
+#define FDT_ERR_MAX 11
+
+#define fdt_get_header(fdt, field) \
+ (fdt32_to_cpu(((struct fdt_header *)(fdt))->field))
+#define fdt_magic(fdt) (fdt_get_header(fdt, magic))
+#define fdt_totalsize(fdt) (fdt_get_header(fdt, totalsize))
+#define fdt_off_dt_struct(fdt) (fdt_get_header(fdt, off_dt_struct))
+#define fdt_off_dt_strings(fdt) (fdt_get_header(fdt, off_dt_strings))
+#define fdt_off_mem_rsvmap(fdt) (fdt_get_header(fdt, off_mem_rsvmap))
+#define fdt_version(fdt) (fdt_get_header(fdt, version))
+#define fdt_last_comp_version(fdt) (fdt_get_header(fdt, last_comp_version))
+#define fdt_boot_cpuid_phys(fdt) (fdt_get_header(fdt, boot_cpuid_phys))
+#define fdt_size_dt_strings(fdt) (fdt_get_header(fdt, size_dt_strings))
+#define fdt_size_dt_struct(fdt) (fdt_get_header(fdt, size_dt_struct))
+
+#define fdt_set_header(fdt, field, val) \
+ ((struct fdt_header *)(fdt))->field = cpu_to_fdt32(val)
+
+void *fdt_offset_ptr(const void *fdt, int offset, int checklen);
+
+#define fdt_offset_ptr_typed(fdt, offset, var) \
+ ((typeof(var))(fdt_offset_ptr((fdt), (offset), sizeof(*(var)))))
+
+int fdt_move(const void *fdt, void *buf, int bufsize);
+
+/* Read-only functions */
+char *fdt_string(const void *fdt, int stroffset);
+
+int fdt_subnode_offset_namelen(const void *fdt, int parentoffset,
+ const char *name, int namelen);
+int fdt_subnode_offset(const void *fdt, int parentoffset, const char *name);
+
+int fdt_path_offset(const void *fdt, const char *path);
+
+struct fdt_property *fdt_get_property(const void *fdt, int nodeoffset,
+ const char *name, int *lenp);
+void *fdt_getprop(const void *fdt, int nodeoffset,
+ const char *name, int *lenp);
+
+uint32_t fdt_next_tag(const void *fdt, int offset,
+ int *nextoffset, char **namep);
+
+/* Write-in-place functions */
+int fdt_setprop_inplace(void *fdt, int nodeoffset, const char *name,
+ const void *val, int len);
+
+#define fdt_setprop_inplace_typed(fdt, nodeoffset, name, val) \
+ ({ \
+ typeof(val) x = val; \
+ fdt_setprop_inplace(fdt, nodeoffset, name, &x, sizeof(x)); \
+ })
+
+int fdt_nop_property(void *fdt, int nodeoffset, const char *name);
+int fdt_nop_node(void *fdt, int nodeoffset);
+
+/* Sequential-write functions */
+int fdt_create(void *buf, int bufsize);
+int fdt_add_reservemap_entry(void *fdt, uint64_t addr, uint64_t size);
+int fdt_finish_reservemap(void *fdt);
+int fdt_begin_node(void *fdt, const char *name);
+int fdt_property(void *fdt, const char *name, const void *val, int len);
+#define fdt_property_typed(fdt, name, val) \
+ ({ \
+ typeof(val) x = (val); \
+ fdt_property((fdt), (name), &x, sizeof(x)); \
+ })
+#define fdt_property_string(fdt, name, str) \
+ fdt_property(fdt, name, str, strlen(str)+1)
+int fdt_end_node(void *fdt);
+int fdt_finish(void *fdt);
+
+/* Read-write functions */
+int fdt_open_into(void *fdt, void *buf, int bufsize);
+int fdt_pack(void *fdt);
+
+int fdt_setprop(void *fdt, int nodeoffset, const char *name,
+ const void *val, int len);
+#define fdt_setprop_typed(fdt, nodeoffset, name, val) \
+ ({ \
+ typeof(val) x = (val); \
+ fdt_setprop((fdt), (nodeoffset), (name), &x, sizeof(x)); \
+ })
+#define fdt_setprop_string(fdt, nodeoffset, name, str) \
+ fdt_setprop((fdt), (nodeoffset), (name), (str), strlen(str)+1)
+int fdt_delprop(void *fdt, int nodeoffset, const char *name);
+int fdt_add_subnode_namelen(void *fdt, int parentoffset,
+ const char *name, int namelen);
+int fdt_add_subnode(void *fdt, int parentoffset, const char *name);
+int fdt_del_node(void *fdt, int nodeoffset);
+
+/* Extra functions */
+const char *fdt_strerror(int errval);
+
+#endif /* _LIBFDT_H */
diff --git a/include/libfdt_env.h b/include/libfdt_env.h
new file mode 100644
index 0000000..6c77852
--- /dev/null
+++ b/include/libfdt_env.h
@@ -0,0 +1,16 @@
+#ifndef _LIBFDT_ENV_H
+#define _LIBFDT_ENV_H
+
+#include <stddef.h>
+#include <linux/types.h>
+#include <asm/byteorder.h>
+#include <linux/string.h>
+
+struct fdt_header *fdt; /* Pointer to the working fdt */
+
+#define fdt32_to_cpu(x) __be32_to_cpu(x)
+#define cpu_to_fdt32(x) __cpu_to_be32(x)
+#define fdt64_to_cpu(x) __be64_to_cpu(x)
+#define cpu_to_fdt64(x) __cpu_to_be64(x)
+
+#endif /* _LIBFDT_ENV_H */
diff --git a/include/linux/mii.h b/include/linux/mii.h
new file mode 100644
index 0000000..7c63095
--- /dev/null
+++ b/include/linux/mii.h
@@ -0,0 +1,158 @@
+/*
+ * linux/mii.h: definitions for MII-compatible transceivers
+ * Originally drivers/net/sunhme.h.
+ *
+ * Copyright (C) 1996, 1999, 2001 David S. Miller (davem@redhat.com)
+ */
+
+#ifndef __LINUX_MII_H__
+#define __LINUX_MII_H__
+
+/* Generic MII registers. */
+
+#define MII_BMCR 0x00 /* Basic mode control register */
+#define MII_BMSR 0x01 /* Basic mode status register */
+#define MII_PHYSID1 0x02 /* PHYS ID 1 */
+#define MII_PHYSID2 0x03 /* PHYS ID 2 */
+#define MII_ADVERTISE 0x04 /* Advertisement control reg */
+#define MII_LPA 0x05 /* Link partner ability reg */
+#define MII_EXPANSION 0x06 /* Expansion register */
+#define MII_DCOUNTER 0x12 /* Disconnect counter */
+#define MII_FCSCOUNTER 0x13 /* False carrier counter */
+#define MII_NWAYTEST 0x14 /* N-way auto-neg test reg */
+#define MII_RERRCOUNTER 0x15 /* Receive error counter */
+#define MII_SREVISION 0x16 /* Silicon revision */
+#define MII_RESV1 0x17 /* Reserved... */
+#define MII_LBRERROR 0x18 /* Lpback, rx, bypass error */
+#define MII_PHYADDR 0x19 /* PHY address */
+#define MII_RESV2 0x1a /* Reserved... */
+#define MII_TPISTATUS 0x1b /* TPI status for 10mbps */
+#define MII_NCONFIG 0x1c /* Network interface config */
+
+/* Basic mode control register. */
+#define BMCR_RESV 0x003f /* Unused... */
+#define BMCR_SPEED1000 0x0040 /* MSB of Speed (1000) */
+#define BMCR_CTST 0x0080 /* Collision test */
+#define BMCR_FULLDPLX 0x0100 /* Full duplex */
+#define BMCR_ANRESTART 0x0200 /* Auto negotiation restart */
+#define BMCR_ISOLATE 0x0400 /* Disconnect DP83840 from MII */
+#define BMCR_PDOWN 0x0800 /* Powerdown the DP83840 */
+#define BMCR_ANENABLE 0x1000 /* Enable auto negotiation */
+#define BMCR_SPEED100 0x2000 /* Select 100Mbps */
+#define BMCR_LOOPBACK 0x4000 /* TXD loopback bits */
+#define BMCR_RESET 0x8000 /* Reset the DP83840 */
+
+/* Basic mode status register. */
+#define BMSR_ERCAP 0x0001 /* Ext-reg capability */
+#define BMSR_JCD 0x0002 /* Jabber detected */
+#define BMSR_LSTATUS 0x0004 /* Link status */
+#define BMSR_ANEGCAPABLE 0x0008 /* Able to do auto-negotiation */
+#define BMSR_RFAULT 0x0010 /* Remote fault detected */
+#define BMSR_ANEGCOMPLETE 0x0020 /* Auto-negotiation complete */
+#define BMSR_RESV 0x07c0 /* Unused... */
+#define BMSR_10HALF 0x0800 /* Can do 10mbps, half-duplex */
+#define BMSR_10FULL 0x1000 /* Can do 10mbps, full-duplex */
+#define BMSR_100HALF 0x2000 /* Can do 100mbps, half-duplex */
+#define BMSR_100FULL 0x4000 /* Can do 100mbps, full-duplex */
+#define BMSR_100BASE4 0x8000 /* Can do 100mbps, 4k packets */
+
+/* Advertisement control register. */
+#define ADVERTISE_SLCT 0x001f /* Selector bits */
+#define ADVERTISE_CSMA 0x0001 /* Only selector supported */
+#define ADVERTISE_10HALF 0x0020 /* Try for 10mbps half-duplex */
+#define ADVERTISE_10FULL 0x0040 /* Try for 10mbps full-duplex */
+#define ADVERTISE_100HALF 0x0080 /* Try for 100mbps half-duplex */
+#define ADVERTISE_100FULL 0x0100 /* Try for 100mbps full-duplex */
+#define ADVERTISE_100BASE4 0x0200 /* Try for 100mbps 4k packets */
+#define ADVERTISE_RESV 0x1c00 /* Unused... */
+#define ADVERTISE_RFAULT 0x2000 /* Say we can detect faults */
+#define ADVERTISE_LPACK 0x4000 /* Ack link partners response */
+#define ADVERTISE_NPAGE 0x8000 /* Next page bit */
+
+#define ADVERTISE_FULL (ADVERTISE_100FULL | ADVERTISE_10FULL | \
+ ADVERTISE_CSMA)
+#define ADVERTISE_ALL (ADVERTISE_10HALF | ADVERTISE_10FULL | \
+ ADVERTISE_100HALF | ADVERTISE_100FULL)
+
+/* Link partner ability register. */
+#define LPA_SLCT 0x001f /* Same as advertise selector */
+#define LPA_10HALF 0x0020 /* Can do 10mbps half-duplex */
+#define LPA_10FULL 0x0040 /* Can do 10mbps full-duplex */
+#define LPA_100HALF 0x0080 /* Can do 100mbps half-duplex */
+#define LPA_100FULL 0x0100 /* Can do 100mbps full-duplex */
+#define LPA_100BASE4 0x0200 /* Can do 100mbps 4k packets */
+#define LPA_RESV 0x1c00 /* Unused... */
+#define LPA_RFAULT 0x2000 /* Link partner faulted */
+#define LPA_LPACK 0x4000 /* Link partner acked us */
+#define LPA_NPAGE 0x8000 /* Next page bit */
+
+#define LPA_DUPLEX (LPA_10FULL | LPA_100FULL)
+#define LPA_100 (LPA_100FULL | LPA_100HALF | LPA_100BASE4)
+
+/* Expansion register for auto-negotiation. */
+#define EXPANSION_NWAY 0x0001 /* Can do N-way auto-nego */
+#define EXPANSION_LCWP 0x0002 /* Got new RX page code word */
+#define EXPANSION_ENABLENPAGE 0x0004 /* This enables npage words */
+#define EXPANSION_NPCAPABLE 0x0008 /* Link partner supports npage */
+#define EXPANSION_MFAULTS 0x0010 /* Multiple faults detected */
+#define EXPANSION_RESV 0xffe0 /* Unused... */
+
+/* N-way test register. */
+#define NWAYTEST_RESV1 0x00ff /* Unused... */
+#define NWAYTEST_LOOPBACK 0x0100 /* Enable loopback for N-way */
+#define NWAYTEST_RESV2 0xfe00 /* Unused... */
+
+
+/**
+ * mii_nway_result
+ * @negotiated: value of MII ANAR and'd with ANLPAR
+ *
+ * Given a set of MII abilities, check each bit and returns the
+ * currently supported media, in the priority order defined by
+ * IEEE 802.3u. We use LPA_xxx constants but note this is not the
+ * value of LPA solely, as described above.
+ *
+ * The one exception to IEEE 802.3u is that 100baseT4 is placed
+ * between 100T-full and 100T-half. If your phy does not support
+ * 100T4 this is fine. If your phy places 100T4 elsewhere in the
+ * priority order, you will need to roll your own function.
+ */
+static inline unsigned int mii_nway_result (unsigned int negotiated)
+{
+ unsigned int ret;
+
+ if (negotiated & LPA_100FULL)
+ ret = LPA_100FULL;
+ else if (negotiated & LPA_100BASE4)
+ ret = LPA_100BASE4;
+ else if (negotiated & LPA_100HALF)
+ ret = LPA_100HALF;
+ else if (negotiated & LPA_10FULL)
+ ret = LPA_10FULL;
+ else
+ ret = LPA_10HALF;
+
+ return ret;
+}
+
+/**
+ * mii_duplex
+ * @duplex_lock: Non-zero if duplex is locked at full
+ * @negotiated: value of MII ANAR and'd with ANLPAR
+ *
+ * A small helper function for a common case. Returns one
+ * if the media is operating or locked at full duplex, and
+ * returns zero otherwise.
+ */
+static inline unsigned int mii_duplex (unsigned int duplex_lock,
+ unsigned int negotiated)
+{
+ if (duplex_lock)
+ return 1;
+ if (mii_nway_result(negotiated) & LPA_DUPLEX)
+ return 1;
+ return 0;
+}
+
+
+#endif /* __LINUX_MII_H__ */
diff --git a/include/linux/stat.h b/include/linux/stat.h
index 4d05aa9..43fd53f 100644
--- a/include/linux/stat.h
+++ b/include/linux/stat.h
@@ -7,7 +7,7 @@
extern "C" {
#endif
-#define S_IFMT 00170000 /* type of file */
+#define S_IFMT 00170000 /* type of file */
#define S_IFSOCK 0140000 /* named socket */
#define S_IFLNK 0120000 /* symbolic link */
#define S_IFREG 0100000 /* regular */
@@ -49,20 +49,20 @@
ino_t st_ino; /* file id */
mode_t st_mode; /* ownership/protection */
nlink_t st_nlink; /* number of links */
- uid_t st_uid; /* user id */
- gid_t st_gid; /* group id */
+ uid_t st_uid; /* user id */
+ gid_t st_gid; /* group id */
dev_t st_rdev;
off_t st_size; /* file size in # of bytes */
- unsigned long st_blksize; /* block size */
- unsigned long st_blocks; /* file size in # of blocks */
- unsigned long st_atime; /* time file was last accessed */
- unsigned long __unused1;
- unsigned long st_mtime; /* time file was last modified */
- unsigned long __unused2;
- unsigned long st_ctime; /* time file status was last changed */
- unsigned long __unused3;
- unsigned long __unused4;
- unsigned long __unused5;
+ unsigned long st_blksize; /* block size */
+ unsigned long st_blocks; /* file size in # of blocks */
+ unsigned long st_atime; /* time file was last accessed */
+ unsigned long __unused1;
+ unsigned long st_mtime; /* time file was last modified */
+ unsigned long __unused2;
+ unsigned long st_ctime; /* time file status was last changed */
+ unsigned long __unused3;
+ unsigned long __unused4;
+ unsigned long __unused5;
};
#endif /* __PPC__ */
@@ -97,34 +97,59 @@
#if defined (__MIPS__)
struct stat {
- dev_t st_dev;
- long st_pad1[3];
- ino_t st_ino;
- mode_t st_mode;
- nlink_t st_nlink;
- uid_t st_uid;
- gid_t st_gid;
- dev_t st_rdev;
- long st_pad2[2];
- off_t st_size;
- long st_pad3;
+ dev_t st_dev;
+ long st_pad1[3];
+ ino_t st_ino;
+ mode_t st_mode;
+ nlink_t st_nlink;
+ uid_t st_uid;
+ gid_t st_gid;
+ dev_t st_rdev;
+ long st_pad2[2];
+ off_t st_size;
+ long st_pad3;
/*
* Actually this should be timestruc_t st_atime, st_mtime and st_ctime
* but we don't have it under Linux.
*/
- time_t st_atime;
- long reserved0;
- time_t st_mtime;
- long reserved1;
- time_t st_ctime;
- long reserved2;
- long st_blksize;
- long st_blocks;
- long st_pad4[14];
+ time_t st_atime;
+ long reserved0;
+ time_t st_mtime;
+ long reserved1;
+ time_t st_ctime;
+ long reserved2;
+ long st_blksize;
+ long st_blocks;
+ long st_pad4[14];
};
#endif /* __MIPS__ */
+#if defined(__AVR32__)
+
+struct stat {
+ unsigned long st_dev;
+ unsigned long st_ino;
+ unsigned short st_mode;
+ unsigned short st_nlink;
+ unsigned short st_uid;
+ unsigned short st_gid;
+ unsigned long st_rdev;
+ unsigned long st_size;
+ unsigned long st_blksize;
+ unsigned long st_blocks;
+ unsigned long st_atime;
+ unsigned long st_atime_nsec;
+ unsigned long st_mtime;
+ unsigned long st_mtime_nsec;
+ unsigned long st_ctime;
+ unsigned long st_ctime_nsec;
+ unsigned long __unused4;
+ unsigned long __unused5;
+};
+
+#endif /* __AVR32__ */
+
#ifdef __cplusplus
}
#endif
diff --git a/include/ppc405.h b/include/ppc405.h
index 08f10d2..a2503a9 100644
--- a/include/ppc405.h
+++ b/include/ppc405.h
@@ -570,6 +570,8 @@
#define SDR_ICTX0_STAT 0x40000000
#define SDR_ICTX1_STAT 0x20000000
+#define SDR_PINSTP 0x40
+
/******************************************************************************
* Control
******************************************************************************/
diff --git a/include/ppc440.h b/include/ppc440.h
index 9b15c2c..bc1d7aa 100644
--- a/include/ppc440.h
+++ b/include/ppc440.h
@@ -148,7 +148,7 @@
#define sdrcfgd (SDR_DCR_BASE+0x1)
#define sdr_sdstp0 0x0020 /* */
#define sdr_sdstp1 0x0021 /* */
-#define sdr_pinstp 0x0040
+#define SDR_PINSTP 0x0040
#define sdr_sdcs 0x0060
#define sdr_ecid0 0x0080
#define sdr_ecid1 0x0081
@@ -3290,29 +3290,6 @@
#define GPIO1_ISR3H (GPIO1_BASE+0x44)
#endif
-#define GPIO_GROUP_MAX 2
-#define GPIO_MAX 32
-#define GPIO_ALT1_SEL 0x40000000 /* GPIO_OUT value put in GPIO_TSx for the GPIO nb 0 */
-#define GPIO_ALT2_SEL 0x80000000 /* GPIO_OUT value put in GPIO_TSx for the GPIO nb 1 */
-#define GPIO_ALT3_SEL 0xC0000000 /* GPIO_OUT value put in GPIO_TSx for the GPIO nb 2 */
-#define GPIO_MASK 0xC0000000 /* GPIO_MASK */
-#define GPIO_IN_SEL 0x40000000 /* GPIO_IN value put in GPIO_ISx for the GPIO nb 0 */
- /* For the other GPIO number, you must shift */
-
-#define GPIO_VAL(gpio) (0x80000000 >> (gpio))
-
-#ifndef __ASSEMBLY__
-
-typedef enum gpio_select { GPIO_SEL, GPIO_ALT1, GPIO_ALT2, GPIO_ALT3 } gpio_select_t;
-typedef enum gpio_driver { GPIO_DIS, GPIO_IN, GPIO_OUT, GPIO_BI } gpio_driver_t;
-
-typedef struct { unsigned long add; /* gpio core base address */
- gpio_driver_t in_out; /* Driver Setting */
- gpio_select_t alt_nb; /* Selected Alternate */
-} gpio_param_s;
-
-#endif /* __ASSEMBLY__ */
-
/*
* Macros for accessing the indirect EBC registers
*/
diff --git a/include/serial.h b/include/serial.h
index 4880059..f7412fd 100644
--- a/include/serial.h
+++ b/include/serial.h
@@ -23,7 +23,7 @@
extern struct serial_device * default_serial_console (void);
#if defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_440) \
- || defined(CONFIG_405EP) || defined(CONFIG_MPC5xxx)
+ || defined(CONFIG_405EP) || defined(CONFIG_405EZ) || defined(CONFIG_MPC5xxx)
extern struct serial_device serial0_device;
extern struct serial_device serial1_device;
#if defined(CFG_NS16550_SERIAL)
diff --git a/include/tsi108.h b/include/tsi108.h
new file mode 100644
index 0000000..ba62e7a
--- /dev/null
+++ b/include/tsi108.h
@@ -0,0 +1,221 @@
+/*****************************************************************************
+ * (C) Copyright 2003; Tundra Semiconductor Corp.
+ * (C) Copyright 2006; Freescale Semiconductor Corp.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *****************************************************************************/
+
+/*
+ * FILENAME: tsi108.h
+ *
+ * Originator: Alex Bounine
+ *
+ * DESCRIPTION:
+ * Common definitions for the Tundra Tsi108 bridge chip
+ *
+ */
+
+#ifndef _TSI108_H_
+#define _TSI108_H_
+
+#define TSI108_HLP_REG_OFFSET (0x0000)
+#define TSI108_PCI_REG_OFFSET (0x1000)
+#define TSI108_CLK_REG_OFFSET (0x2000)
+#define TSI108_PB_REG_OFFSET (0x3000)
+#define TSI108_SD_REG_OFFSET (0x4000)
+#define TSI108_MPIC_REG_OFFSET (0x7400)
+
+#define PB_ID (0x000)
+#define PB_RSR (0x004)
+#define PB_BUS_MS_SELECT (0x008)
+#define PB_ISR (0x00C)
+#define PB_ARB_CTRL (0x018)
+#define PB_PVT_CTRL2 (0x034)
+#define PB_SCR (0x400)
+#define PB_ERRCS (0x404)
+#define PB_AERR (0x408)
+#define PB_REG_BAR (0x410)
+#define PB_OCN_BAR1 (0x414)
+#define PB_OCN_BAR2 (0x418)
+#define PB_SDRAM_BAR1 (0x41C)
+#define PB_SDRAM_BAR2 (0x420)
+#define PB_MCR (0xC00)
+#define PB_MCMD (0xC04)
+
+#define HLP_B0_ADDR (0x000)
+#define HLP_B1_ADDR (0x010)
+#define HLP_B2_ADDR (0x020)
+#define HLP_B3_ADDR (0x030)
+
+#define HLP_B0_MASK (0x004)
+#define HLP_B1_MASK (0x014)
+#define HLP_B2_MASK (0x024)
+#define HLP_B3_MASK (0x034)
+
+#define HLP_B0_CTRL0 (0x008)
+#define HLP_B1_CTRL0 (0x018)
+#define HLP_B2_CTRL0 (0x028)
+#define HLP_B3_CTRL0 (0x038)
+
+#define HLP_B0_CTRL1 (0x00C)
+#define HLP_B1_CTRL1 (0x01C)
+#define HLP_B2_CTRL1 (0x02C)
+#define HLP_B3_CTRL1 (0x03C)
+
+#define PCI_CSR (0x004)
+#define PCI_P2O_BAR0 (0x010)
+#define PCI_P2O_BAR0_UPPER (0x014)
+#define PCI_P2O_BAR2 (0x018)
+#define PCI_P2O_BAR2_UPPER (0x01C)
+#define PCI_P2O_BAR3 (0x020)
+#define PCI_P2O_BAR3_UPPER (0x024)
+
+#define PCI_MISC_CSR (0x040)
+#define PCI_P2O_PAGE_SIZES (0x04C)
+
+#define PCI_PCIX_STAT (0x0F4)
+
+#define PCI_IRP_STAT (0x184)
+
+#define PCI_PFAB_BAR0 (0x204)
+#define PCI_PFAB_BAR0_UPPER (0x208)
+#define PCI_PFAB_IO (0x20C)
+#define PCI_PFAB_IO_UPPER (0x210)
+
+#define PCI_PFAB_MEM32 (0x214)
+#define PCI_PFAB_MEM32_REMAP (0x218)
+#define PCI_PFAB_MEM32_MASK (0x21C)
+
+#define CG_PLL0_CTRL0 (0x210)
+#define CG_PLL0_CTRL1 (0x214)
+#define CG_PLL1_CTRL0 (0x220)
+#define CG_PLL1_CTRL1 (0x224)
+#define CG_PWRUP_STATUS (0x234)
+
+#define MPIC_CSR(n) (0x30C + (n * 0x40))
+
+#define SD_CTRL (0x000)
+#define SD_STATUS (0x004)
+#define SD_TIMING (0x008)
+#define SD_REFRESH (0x00C)
+#define SD_INT_STATUS (0x010)
+#define SD_INT_ENABLE (0x014)
+#define SD_INT_SET (0x018)
+#define SD_D0_CTRL (0x020)
+#define SD_D1_CTRL (0x024)
+#define SD_D0_BAR (0x028)
+#define SD_D1_BAR (0x02C)
+#define SD_ECC_CTRL (0x040)
+#define SD_DLL_STATUS (0x250)
+
+#define TS_SD_CTRL_ENABLE (1 << 31)
+
+#define PB_ERRCS_ES (1 << 1)
+#define PB_ISR_PBS_RD_ERR (1 << 8)
+#define PCI_IRP_STAT_P_CSR (1 << 23)
+
+/*
+ * I2C : Register address offset definitions
+ */
+#define I2C_CNTRL1 (0x00000000)
+#define I2C_CNTRL2 (0x00000004)
+#define I2C_RD_DATA (0x00000008)
+#define I2C_TX_DATA (0x0000000c)
+
+/*
+ * I2C : Register Bit Masks and Reset Values
+ * definitions for every register
+ */
+
+/* I2C_CNTRL1 : Reset Value */
+#define I2C_CNTRL1_RESET_VALUE (0x0000000a)
+
+/* I2C_CNTRL1 : Register Bits Masks Definitions */
+#define I2C_CNTRL1_DEVCODE (0x0000000f)
+#define I2C_CNTRL1_PAGE (0x00000700)
+#define I2C_CNTRL1_BYTADDR (0x00ff0000)
+#define I2C_CNTRL1_I2CWRITE (0x01000000)
+
+/* I2C_CNTRL1 : Read/Write Bit Mask Definition */
+#define I2C_CNTRL1_RWMASK (0x01ff070f)
+
+/* I2C_CNTRL1 : Unused/Reserved bits Definition */
+#define I2C_CNTRL1_RESERVED (0xfe00f8f0)
+
+/* I2C_CNTRL2 : Reset Value */
+#define I2C_CNTRL2_RESET_VALUE (0x00000000)
+
+/* I2C_CNTRL2 : Register Bits Masks Definitions */
+#define I2C_CNTRL2_SIZE (0x00000003)
+#define I2C_CNTRL2_LANE (0x0000000c)
+#define I2C_CNTRL2_MULTIBYTE (0x00000010)
+#define I2C_CNTRL2_START (0x00000100)
+#define I2C_CNTRL2_WR_STATUS (0x00010000)
+#define I2C_CNTRL2_RD_STATUS (0x00020000)
+#define I2C_CNTRL2_I2C_TO_ERR (0x04000000)
+#define I2C_CNTRL2_I2C_CFGERR (0x08000000)
+#define I2C_CNTRL2_I2C_CMPLT (0x10000000)
+
+/* I2C_CNTRL2 : Read/Write Bit Mask Definition */
+#define I2C_CNTRL2_RWMASK (0x0000011f)
+
+/* I2C_CNTRL2 : Unused/Reserved bits Definition */
+#define I2C_CNTRL2_RESERVED (0xe3fcfee0)
+
+/* I2C_RD_DATA : Reset Value */
+#define I2C_RD_DATA_RESET_VALUE (0x00000000)
+
+/* I2C_RD_DATA : Register Bits Masks Definitions */
+#define I2C_RD_DATA_RBYTE0 (0x000000ff)
+#define I2C_RD_DATA_RBYTE1 (0x0000ff00)
+#define I2C_RD_DATA_RBYTE2 (0x00ff0000)
+#define I2C_RD_DATA_RBYTE3 (0xff000000)
+
+/* I2C_RD_DATA : Read/Write Bit Mask Definition */
+#define I2C_RD_DATA_RWMASK (0x00000000)
+
+/* I2C_RD_DATA : Unused/Reserved bits Definition */
+#define I2C_RD_DATA_RESERVED (0x00000000)
+
+/* I2C_TX_DATA : Reset Value */
+#define I2C_TX_DATA_RESET_VALUE (0x00000000)
+
+/* I2C_TX_DATA : Register Bits Masks Definitions */
+#define I2C_TX_DATA_TBYTE0 (0x000000ff)
+#define I2C_TX_DATA_TBYTE1 (0x0000ff00)
+#define I2C_TX_DATA_TBYTE2 (0x00ff0000)
+#define I2C_TX_DATA_TBYTE3 (0xff000000)
+
+/* I2C_TX_DATA : Read/Write Bit Mask Definition */
+#define I2C_TX_DATA_RWMASK (0xffffffff)
+
+/* I2C_TX_DATA : Unused/Reserved bits Definition */
+#define I2C_TX_DATA_RESERVED (0x00000000)
+
+#define TSI108_I2C_OFFSET 0x7000 /* offset for general use I2C channel */
+#define TSI108_I2C_SDRAM_OFFSET 0x4400 /* offset for SPD I2C channel */
+
+#define I2C_EEPROM_DEVCODE 0xA /* standard I2C EEPROM device code */
+
+/* I2C status codes */
+
+#define TSI108_I2C_SUCCESS 0
+#define TSI108_I2C_PARAM_ERR 1
+#define TSI108_I2C_TIMEOUT_ERR 2
+#define TSI108_I2C_IF_BUSY 3
+#define TSI108_I2C_IF_ERROR 4
+
+#endif /* _TSI108_H_ */
diff --git a/lib_avr32/avr32_linux.c b/lib_avr32/avr32_linux.c
index d128dfb..6095e2f 100644
--- a/lib_avr32/avr32_linux.c
+++ b/lib_avr32/avr32_linux.c
@@ -27,7 +27,7 @@
#include <asm/addrspace.h>
#include <asm/io.h>
#include <asm/setup.h>
-#include <asm/arch/platform.h>
+#include <asm/arch/clk.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -133,7 +133,7 @@
params->hdr.size = tag_size(tag_clock);
params->u.clock.clock_id = ACLOCK_HSB;
params->u.clock.clock_flags = 0;
- params->u.clock.clock_hz = pm_get_clock_freq(CLOCK_HSB);
+ params->u.clock.clock_hz = get_hsb_clk_rate();
#endif
return tag_next(params);
diff --git a/lib_avr32/board.c b/lib_avr32/board.c
index 02c106b..265328a 100644
--- a/lib_avr32/board.c
+++ b/lib_avr32/board.c
@@ -47,11 +47,14 @@
static unsigned long mem_malloc_end = 0;
static unsigned long mem_malloc_brk = 0;
-/* The malloc area is wherever the board wants it to be */
+/* The malloc area is right below the monitor image in RAM */
static void mem_malloc_init(void)
{
- mem_malloc_start = CFG_MALLOC_START;
- mem_malloc_end = CFG_MALLOC_END;
+ unsigned long monitor_addr;
+
+ monitor_addr = CFG_MONITOR_BASE + gd->reloc_off;
+ mem_malloc_end = monitor_addr;
+ mem_malloc_start = mem_malloc_end - CFG_MALLOC_LEN;
mem_malloc_brk = mem_malloc_start;
printf("malloc: Using memory from 0x%08lx to 0x%08lx\n",
@@ -72,6 +75,50 @@
mem_malloc_brk = new;
return ((void *)old);
}
+
+#ifdef CFG_DMA_ALLOC_LEN
+#include <asm/cacheflush.h>
+#include <asm/io.h>
+
+static unsigned long dma_alloc_start;
+static unsigned long dma_alloc_end;
+static unsigned long dma_alloc_brk;
+
+static void dma_alloc_init(void)
+{
+ unsigned long monitor_addr;
+
+ monitor_addr = CFG_MONITOR_BASE + gd->reloc_off;
+ dma_alloc_end = monitor_addr - CFG_MALLOC_LEN;
+ dma_alloc_start = dma_alloc_end - CFG_DMA_ALLOC_LEN;
+ dma_alloc_brk = dma_alloc_start;
+
+ printf("DMA: Using memory from 0x%08lx to 0x%08lx\n",
+ dma_alloc_start, dma_alloc_end);
+
+ dcache_invalidate_range(cached(dma_alloc_start),
+ dma_alloc_end - dma_alloc_start);
+}
+
+void *dma_alloc_coherent(size_t len, unsigned long *handle)
+{
+ unsigned long paddr = dma_alloc_brk;
+
+ if (dma_alloc_brk + len > dma_alloc_end)
+ return NULL;
+
+ dma_alloc_brk = ((paddr + len + CFG_DCACHE_LINESZ - 1)
+ & ~(CFG_DCACHE_LINESZ - 1));
+
+ *handle = paddr;
+ return uncached(paddr);
+}
+#else
+static inline void dma_alloc_init(void)
+{
+
+}
+#endif
static int init_baudrate(void)
{
@@ -122,40 +169,152 @@
printf("at address 0x%08lx\n", gd->bd->bi_flashstart);
}
-void start_u_boot (void)
+void board_init_f(ulong board_type)
{
gd_t gd_data;
+ gd_t *new_gd;
+ bd_t *bd;
+ unsigned long *new_sp;
+ unsigned long monitor_len;
+ unsigned long monitor_addr;
+ unsigned long addr;
+ long sdram_size;
/* Initialize the global data pointer */
memset(&gd_data, 0, sizeof(gd_data));
gd = &gd_data;
- monitor_flash_len = _edata - _text;
-
/* Perform initialization sequence */
+ board_early_init_f();
cpu_init();
- timer_init();
env_init();
init_baudrate();
serial_init();
console_init_f();
display_banner();
+ sdram_size = initdram(board_type);
- board_init_memories();
- mem_malloc_init();
+ /* If we have no SDRAM, we can't go on */
+ if (sdram_size <= 0)
+ panic("No working SDRAM available\n");
+
+ /*
+ * Now that we have DRAM mapped and working, we can
+ * relocate the code and continue running from DRAM.
+ *
+ * Reserve memory at end of RAM for (top down in that order):
+ * - u-boot image
+ * - heap for malloc()
+ * - board info struct
+ * - global data struct
+ * - stack
+ */
+ addr = CFG_SDRAM_BASE + sdram_size;
+ monitor_len = _end - _text;
- gd->bd = malloc(sizeof(bd_t));
- memset(gd->bd, 0, sizeof(bd_t));
- gd->bd->bi_baudrate = gd->baudrate;
- gd->bd->bi_dram[0].start = CFG_SDRAM_BASE;
- gd->bd->bi_dram[0].size = gd->sdram_size;
+ /*
+ * Reserve memory for u-boot code, data and bss.
+ * Round down to next 4 kB limit.
+ */
+ addr -= monitor_len;
+ addr &= ~(4096UL - 1);
+ monitor_addr = addr;
+ /* Reserve memory for malloc() */
+ addr -= CFG_MALLOC_LEN;
+
+#ifdef CFG_DMA_ALLOC_LEN
+ /* Reserve DMA memory (must be cache aligned) */
+ addr &= ~(CFG_DCACHE_LINESZ - 1);
+ addr -= CFG_DMA_ALLOC_LEN;
+#endif
+
+ /* Allocate a Board Info struct on a word boundary */
+ addr -= sizeof(bd_t);
+ addr &= ~3UL;
+ gd->bd = bd = (bd_t *)addr;
+
+ /* Allocate a new global data copy on a 8-byte boundary. */
+ addr -= sizeof(gd_t);
+ addr &= ~7UL;
+ new_gd = (gd_t *)addr;
+
+ /* And finally, a new, bigger stack. */
+ new_sp = (unsigned long *)addr;
+ gd->stack_end = addr;
+ *(--new_sp) = 0;
+ *(--new_sp) = 0;
+
+ /*
+ * Initialize the board information struct with the
+ * information we have.
+ */
+ bd->bi_dram[0].start = CFG_SDRAM_BASE;
+ bd->bi_dram[0].size = sdram_size;
+ bd->bi_baudrate = gd->baudrate;
+
+ memcpy(new_gd, gd, sizeof(gd_t));
+
+ relocate_code((unsigned long)new_sp, new_gd, monitor_addr);
+}
+
+void board_init_r(gd_t *new_gd, ulong dest_addr)
+{
+ extern void malloc_bin_reloc (void);
+#ifndef CFG_ENV_IS_NOWHERE
+ extern char * env_name_spec;
+#endif
+ cmd_tbl_t *cmdtp;
+ bd_t *bd;
+
+ gd = new_gd;
+ bd = gd->bd;
+
+ gd->flags |= GD_FLG_RELOC;
+ gd->reloc_off = dest_addr - CFG_MONITOR_BASE;
+
+ monitor_flash_len = _edata - _text;
+
+ /*
+ * We have to relocate the command table manually
+ */
+ for (cmdtp = &__u_boot_cmd_start;
+ cmdtp != &__u_boot_cmd_end; cmdtp++) {
+ unsigned long addr;
+
+ addr = (unsigned long)cmdtp->cmd + gd->reloc_off;
+ cmdtp->cmd = (typeof(cmdtp->cmd))addr;
+
+ addr = (unsigned long)cmdtp->name + gd->reloc_off;
+ cmdtp->name = (typeof(cmdtp->name))addr;
+
+ if (cmdtp->usage) {
+ addr = (unsigned long)cmdtp->usage + gd->reloc_off;
+ cmdtp->usage = (typeof(cmdtp->usage))addr;
+ }
+#ifdef CFG_LONGHELP
+ if (cmdtp->help) {
+ addr = (unsigned long)cmdtp->help + gd->reloc_off;
+ cmdtp->help = (typeof(cmdtp->help))addr;
+ }
+#endif
+ }
+
+ /* there are some other pointer constants we must deal with */
+#ifndef CFG_ENV_IS_NOWHERE
+ env_name_spec += gd->reloc_off;
+#endif
+
+ timer_init();
+ mem_malloc_init();
+ malloc_bin_reloc();
+ dma_alloc_init();
board_init_info();
flash_init();
- if (gd->bd->bi_flashsize)
+ if (bd->bi_flashsize)
display_flash_config();
- if (gd->bd->bi_dram[0].size)
+ if (bd->bi_dram[0].size)
display_dram_config();
gd->bd->bi_boot_params = malloc(CFG_BOOTPARAMS_LEN);
@@ -169,6 +328,13 @@
jumptable_init();
console_init_r();
+#if (CONFIG_COMMANDS & CFG_CMD_NET)
+#if defined(CONFIG_NET_MULTI)
+ puts("Net: ");
+#endif
+ eth_initialize(gd->bd);
+#endif
+
for (;;) {
main_loop();
}
diff --git a/lib_blackfin/Makefile b/lib_blackfin/Makefile
index 3197fe1..a7aaef7 100644
--- a/lib_blackfin/Makefile
+++ b/lib_blackfin/Makefile
@@ -1,7 +1,7 @@
#
# U-boot Makefile
#
-# Copyright (c) 2005 blackfin.uclinux.org
+# Copyright (c) 2005-2007 Analog Devices Inc.
#
# (C) Copyright 2000-2006
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
+# Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+# MA 02110-1301 USA
#
include $(TOPDIR)/config.mk
diff --git a/lib_blackfin/bf533_linux.c b/lib_blackfin/bf533_linux.c
index 1b0d90a..3b9c4df 100644
--- a/lib_blackfin/bf533_linux.c
+++ b/lib_blackfin/bf533_linux.c
@@ -1,7 +1,7 @@
/*
* U-boot - bf533_linux.c
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
/* Dummy functions, currently not in Use */
diff --git a/lib_blackfin/bf533_string.c b/lib_blackfin/bf533_string.c
index 85b1150..1553f1b 100644
--- a/lib_blackfin/bf533_string.c
+++ b/lib_blackfin/bf533_string.c
@@ -1,7 +1,7 @@
/*
* U-boot - bf533_string.c Contains library routines.
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,22 +21,16 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <common.h>
#include <asm/setup.h>
-#include <asm/page.h>
#include <config.h>
#include <asm/blackfin.h>
#include <asm/io.h>
-
-extern void blackfin_icache_flush_range(const void *, const void *);
-extern void blackfin_dcache_flush_range(const void *, const void *);
-extern void *memcpy_ASM(void *dest, const void *src, size_t count);
-
-void *dma_memcpy(void *, const void *, size_t);
+#include "cache.h"
char *strcpy(char *dest, const char *src)
{
@@ -118,44 +112,7 @@
return __res1;
}
-/*
- * memcpy - Copy one area of memory to another
- * @dest: Where to copy to
- * @src: Where to copy from
- * @count: The size of the area.
- *
- * You should not use this function to access IO space, use memcpy_toio()
- * or memcpy_fromio() instead.
- */
-void *memcpy(void *dest, const void *src, size_t count)
-{
- char *tmp = (char *)dest, *s = (char *)src;
-
- /* L1_ISRAM can only be accessed via dma */
- if ((tmp >= (char *)L1_ISRAM) && (tmp < (char *)L1_ISRAM_END)) {
- /* L1 is the destination */
- dma_memcpy(dest, src, count);
-
- if (icache_status()) {
- blackfin_icache_flush_range(src, src + count);
- }
- } else if ((s >= (char *)L1_ISRAM) && (s < (char *)L1_ISRAM_END)) {
- /* L1 is the source */
- dma_memcpy(dest, src, count);
-
- if (icache_status()) {
- blackfin_icache_flush_range(dest, dest + count);
- }
- if (dcache_status()) {
- blackfin_dcache_flush_range(dest, dest + count);
- }
- } else {
- memcpy_ASM(dest, src, count);
- }
- return dest;
-}
-
-void *dma_memcpy(void *dest, const void *src, size_t count)
+static void *dma_memcpy(void *dest, const void *src, size_t count)
{
*pMDMA_D0_IRQ_STATUS = DMA_DONE | DMA_ERR;
@@ -189,3 +146,40 @@
src += count;
return dest;
}
+
+/*
+ * memcpy - Copy one area of memory to another
+ * @dest: Where to copy to
+ * @src: Where to copy from
+ * @count: The size of the area.
+ *
+ * You should not use this function to access IO space, use memcpy_toio()
+ * or memcpy_fromio() instead.
+ */
+extern void *memcpy_ASM(void *dest, const void *src, size_t count);
+void *memcpy(void *dest, const void *src, size_t count)
+{
+ char *tmp = (char *) dest, *s = (char *) src;
+
+ if (dcache_status()) {
+ blackfin_dcache_flush_range(src, src+count);
+ }
+ /* L1_ISRAM can only be accessed via dma */
+ if ((tmp >= (char *)L1_ISRAM) && (tmp < (char *)L1_ISRAM_END)) {
+ /* L1 is the destination */
+ dma_memcpy(dest,src,count);
+ } else if ((s >= (char *)L1_ISRAM) && (s < (char *)L1_ISRAM_END)) {
+ /* L1 is the source */
+ dma_memcpy(dest,src,count);
+
+ if (icache_status()) {
+ blackfin_icache_flush_range(dest, dest+count);
+ }
+ if (dcache_status()) {
+ blackfin_dcache_invalidate_range(dest, dest+count);
+ }
+ } else {
+ memcpy_ASM(dest,src,count);
+ }
+ return dest;
+}
diff --git a/lib_blackfin/blackfin_board.h b/lib_blackfin/blackfin_board.h
index e0b96da..1353421 100644
--- a/lib_blackfin/blackfin_board.h
+++ b/lib_blackfin/blackfin_board.h
@@ -1,7 +1,7 @@
/*
* U-boot - blackfin_board.h
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#ifndef __BLACKFIN_BOARD_H__
diff --git a/lib_blackfin/board.c b/lib_blackfin/board.c
index 1a0a282..1538da3 100644
--- a/lib_blackfin/board.c
+++ b/lib_blackfin/board.c
@@ -1,7 +1,7 @@
/*
* U-boot - board.c First C file to be called contains init routines
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
#include <common.h>
@@ -182,7 +182,7 @@
icplb_table[j][1] = L1_IMEMORY;
j++;
- for (i = 0; i <= CONFIG_MEM_SIZE / 4; i++) {
+ for (i = 0; i < CONFIG_MEM_SIZE / 4; i++) {
icplb_table[j][0] = (i * 4 * 1024 * 1024);
if (i * 4 * 1024 * 1024 <= CFG_MONITOR_BASE
&& (i + 1) * 4 * 1024 * 1024 >= CFG_MONITOR_BASE) {
@@ -193,14 +193,19 @@
j++;
}
#if defined(CONFIG_BF561)
+ /* MAC space */
+ icplb_table[j][0] = 0x2C000000;
+ icplb_table[j][1] = SDRAM_INON_CHBL;
+ j++;
/* Async Memory space */
for (i = 0; i < 3; i++) {
- icplb_table[j++][0] = 0x20000000 + i * 4 * 1024 * 1024;
- icplb_table[j++][1] = SDRAM_IGENERIC;
+ icplb_table[j][0] = 0x20000000 + i * 4 * 1024 * 1024;
+ icplb_table[j][1] = SDRAM_INON_CHBL;
+ j++;
}
#else
icplb_table[j][0] = 0x20000000;
- icplb_table[j][1] = SDRAM_IGENERIC;
+ icplb_table[j][1] = SDRAM_INON_CHBL;
#endif
j = 0;
dcplb_table[j][0] = 0xFF800000;
@@ -220,13 +225,15 @@
#if defined(CONFIG_BF561)
/* MAC space */
- dcplb_table[j++][0] = CONFIG_ASYNC_EBIU_BASE;
- dcplb_table[j++][1] = SDRAM_EBIU;
+ dcplb_table[j][0] = 0x2C000000;
+ dcplb_table[j][1] = SDRAM_EBIU;
+ j++;
/* Flash space */
- for (i = 0; i < 2; i++) {
- dcplb_table[j++][0] = 0x20000000 + i * 4 * 1024 * 1024;
- dcplb_table[j++][1] = SDRAM_EBIU;
+ for (i = 0; i < 3; i++) {
+ dcplb_table[j][0] = 0x20000000 + i * 4 * 1024 * 1024;
+ dcplb_table[j][1] = SDRAM_EBIU;
+ j++;
}
#else
dcplb_table[j][0] = 0x20000000;
diff --git a/lib_blackfin/cache.c b/lib_blackfin/cache.c
index a15914b..9d71bcb 100644
--- a/lib_blackfin/cache.c
+++ b/lib_blackfin/cache.c
@@ -1,7 +1,7 @@
/*
* U-boot - cache.c
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,17 +21,15 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
/* for now: just dummy functions to satisfy the linker */
#include <config.h>
#include <common.h>
#include <asm/blackfin.h>
-
-extern void blackfin_icache_flush_range(unsigned long, unsigned long);
-extern void blackfin_dcache_flush_range(unsigned long, unsigned long);
+#include "cache.h"
void flush_cache(unsigned long dummy1, unsigned long dummy2)
{
@@ -43,9 +41,9 @@
return;
if (icache_status())
- blackfin_icache_flush_range(dummy1, dummy1 + dummy2);
+ blackfin_icache_flush_range((void*)dummy1, (void*)(dummy1 + dummy2));
if (dcache_status())
- blackfin_dcache_flush_range(dummy1, dummy1 + dummy2);
+ blackfin_dcache_flush_range((void*)dummy1, (void*)(dummy1 + dummy2));
return;
}
diff --git a/lib_blackfin/cache.h b/lib_blackfin/cache.h
new file mode 100644
index 0000000..3ea6809
--- /dev/null
+++ b/lib_blackfin/cache.h
@@ -0,0 +1,35 @@
+/*
+ * U-boot - prototypes for cache handling functions.
+ *
+ * Copyright (c) 2005-2007 Analog Devices Inc.
+ *
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#ifndef _LIB_BLACKFIN_CACHE_H_
+#define _LIB_BLACKFIN_CACHE_H_
+
+extern void blackfin_icache_flush_range(const void *, const void *);
+extern void blackfin_dcache_flush_range(const void *, const void *);
+extern void blackfin_dcache_invalidate_range(const void *, const void *);
+
+#endif
diff --git a/lib_blackfin/memcmp.S b/lib_blackfin/memcmp.S
index fcea5b3..9b58832 100644
--- a/lib_blackfin/memcmp.S
+++ b/lib_blackfin/memcmp.S
@@ -1,17 +1,8 @@
/*
- * File: arch/blackfin/lib/memcmp.S
- * Based on:
- * Author:
- *
- * Created:
- * Description:
- *
- * Rev: $Id: memcmp.S 2386 2006-11-01 04:57:26Z magicyang $
- *
- * Modified:
- * Copyright 2004-2006 Analog Devices Inc.
+ * File: memcmp.S
*
- * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ * Copyright 2004-2007 Analog Devices Inc.
+ * Enter bugs at http://blackfin.uclinux.org/
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
diff --git a/lib_blackfin/memcpy.S b/lib_blackfin/memcpy.S
index a73ff90..24577be 100644
--- a/lib_blackfin/memcpy.S
+++ b/lib_blackfin/memcpy.S
@@ -1,22 +1,8 @@
/*
- * File: arch/blackfin/lib/memcpy.S
- * Based on:
- * Author:
+ * File: memcpy.S
*
- * Created:
- * Description: internal version of memcpy(), issued by the compiler
- * to copy blocks of data around.
- * This is really memmove() - it has to be able to deal with
- * possible overlaps, because that ambiguity is when the compiler
- * gives up and calls a function. We have our own, internal version
- * so that we get something we trust, even if the user has redefined
- * the normal symbol.
- * Rev: $Id: memcpy.S 2775 2007-02-21 13:58:44Z hennerich $
- *
- * Modified:
- * Copyright 2004-2006 Analog Devices Inc.
- *
- * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ * Copyright 2004-2007 Analog Devices Inc.
+ * Enter bugs at http://blackfin.uclinux.org/
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
@@ -33,6 +19,7 @@
* to the Free Software Foundation, Inc.,
* 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
+
.align 2
.globl _memcpy_ASM;
diff --git a/lib_blackfin/memmove.S b/lib_blackfin/memmove.S
index 79558f9..46f79ed 100644
--- a/lib_blackfin/memmove.S
+++ b/lib_blackfin/memmove.S
@@ -1,17 +1,8 @@
/*
- * File: arch/blackfin/lib/memmove.S
- * Based on:
- * Author:
- *
- * Created:
- * Description:
- *
- * Rev: $Id: memmove.S 2205 2006-09-23 07:53:49Z vapier $
- *
- * Modified:
- * Copyright 2004-2006 Analog Devices Inc.
+ * File: memmove.S
*
- * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ * Copyright 2004-2007 Analog Devices Inc.
+ * Enter bugs at http://blackfin.uclinux.org/
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
diff --git a/lib_blackfin/memset.S b/lib_blackfin/memset.S
index 7e6ee19..c33c551 100644
--- a/lib_blackfin/memset.S
+++ b/lib_blackfin/memset.S
@@ -1,17 +1,8 @@
/*
- * File: arch/blackfin/lib/memset.S
- * Based on:
- * Author:
+ * File: memset.S
*
- * Created:
- * Description:
- *
- * Rev: $Id: memset.S 2769 2007-02-19 16:45:53Z hennerich $
- *
- * Modified:
- * Copyright 2004-2006 Analog Devices Inc.
- *
- * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ * Copyright 2004-2007 Analog Devices Inc.
+ * Enter bugs at http://blackfin.uclinux.org/
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
@@ -29,7 +20,6 @@
* 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
-
.align 2
/*
diff --git a/lib_blackfin/muldi3.c b/lib_blackfin/muldi3.c
index da55711..bf1ca53 100644
--- a/lib_blackfin/muldi3.c
+++ b/lib_blackfin/muldi3.c
@@ -1,7 +1,7 @@
/*
* U-boot - muldi3.c contains routines for mult and div
*
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -18,8 +18,8 @@
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
*/
/* Generic function got from GNU gcc package, libgcc2.c */
diff --git a/lib_microblaze/board.c b/lib_microblaze/board.c
index 026d247..c95125a 100644
--- a/lib_microblaze/board.c
+++ b/lib_microblaze/board.c
@@ -1,6 +1,8 @@
/*
+ * (C) Copyright 2007 Michal Simek
* (C) Copyright 2004 Atmark Techno, Inc.
*
+ * Michal SIMEK <monstr@monstr.eu>
* Yasushi SHOJI <yashi@atmark-techno.com>
*
* See file CREDITS for list of people who contributed to this
@@ -13,7 +15,7 @@
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
@@ -30,8 +32,18 @@
DECLARE_GLOBAL_DATA_PTR;
-const char version_string[] =
- U_BOOT_VERSION" (" __DATE__ " - " __TIME__ ")";
+const char version_string[] = U_BOOT_VERSION " (" __DATE__ " - " __TIME__ ")";
+
+#ifdef CFG_GPIO_0
+extern int gpio_init (void);
+#endif
+#ifdef CFG_INTC_0
+extern int interrupts_init (void);
+#endif
+#if (CONFIG_COMMANDS & CFG_CMD_NET)
+extern int eth_init (bd_t * bis);
+extern int getenv_IPaddr (char *);
+#endif
/*
* Begin and End of memory area for malloc(), and current "brk"
@@ -40,6 +52,18 @@
static ulong mem_malloc_end;
static ulong mem_malloc_brk;
+/*
+ * The Malloc area is immediately below the monitor copy in DRAM
+ * aka CFG_MONITOR_BASE - Note there is no need for reloc_off
+ * as our monitory code is run from SDRAM
+ */
+static void mem_malloc_init (void)
+{
+ mem_malloc_end = (CFG_MALLOC_BASE + CFG_MALLOC_LEN);
+ mem_malloc_start = CFG_MALLOC_BASE;
+ mem_malloc_brk = mem_malloc_start;
+ memset ((void *)mem_malloc_start, 0, mem_malloc_end - mem_malloc_start);
+}
void *sbrk (ptrdiff_t increment)
{
@@ -50,7 +74,7 @@
return (NULL);
}
mem_malloc_brk = new;
- return ((void *) old);
+ return ((void *)old);
}
/*
@@ -68,24 +92,36 @@
typedef int (init_fnc_t) (void);
init_fnc_t *init_sequence[] = {
- serial_init, /* serial communications setup */
+ env_init,
+ serial_init,
+#ifdef CFG_GPIO_0
+ gpio_init,
+#endif
+#ifdef CFG_INTC_0
+ interrupts_init,
+#endif
NULL,
};
-void board_init(void)
+void board_init (void)
{
bd_t *bd;
init_fnc_t **init_fnc_ptr;
-
- /* Pointer is writable since we allocated a register for it. */
- gd = (gd_t *)CFG_GBL_DATA_OFFSET;
- memset((void *)gd, 0, CFG_GBL_DATA_SIZE);
-
- gd->bd = (bd_t *)(gd+1); /* At end of global data */
+ gd = (gd_t *) CFG_GBL_DATA_OFFSET;
+#if (CONFIG_COMMANDS & CFG_CMD_FLASH)
+ ulong flash_size = 0;
+#endif
+ asm ("nop"); /* FIXME gd is not initialize - wait */
+ memset ((void *)gd, 0, CFG_GBL_DATA_SIZE);
+ gd->bd = (bd_t *) (gd + 1); /* At end of global data */
gd->baudrate = CONFIG_BAUDRATE;
-
bd = gd->bd;
bd->bi_baudrate = CONFIG_BAUDRATE;
+ bd->bi_memstart = CFG_SDRAM_BASE;
+ bd->bi_memsize = CFG_SDRAM_SIZE;
+
+ /* Initialise malloc() area */
+ mem_malloc_init ();
for (init_fnc_ptr = init_sequence; *init_fnc_ptr; ++init_fnc_ptr) {
WATCHDOG_RESET ();
@@ -94,6 +130,37 @@
}
}
+#if (CONFIG_COMMANDS & CFG_CMD_FLASH)
+ bd->bi_flashstart = CFG_FLASH_BASE;
+ if (0 < (flash_size = flash_init ())) {
+ bd->bi_flashsize = flash_size;
+ bd->bi_flashoffset = CFG_FLASH_BASE + flash_size;
+ } else {
+ puts ("Flash init FAILED");
+ bd->bi_flashstart = 0;
+ bd->bi_flashsize = 0;
+ bd->bi_flashoffset = 0;
+ }
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_NET)
+ char *s, *e;
+ int i;
+ /* board MAC address */
+ s = getenv ("ethaddr");
+ for (i = 0; i < 6; ++i) {
+ bd->bi_enetaddr[i] = s ? simple_strtoul (s, &e, 16) : 0;
+ if (s)
+ s = (*e) ? e + 1 : e;
+ }
+ /* IP Address */
+ bd->bi_ip_addr = getenv_IPaddr ("ipaddr");
+ eth_init (bd);
+#endif
+
+ /* relocate environment function pointers etc. */
+ env_relocate ();
+
/* main_loop */
for (;;) {
WATCHDOG_RESET ();
@@ -104,5 +171,5 @@
void hang (void)
{
puts ("### ERROR ### Please RESET the board ###\n");
- for (;;);
+ for (;;) ;
}
diff --git a/lib_microblaze/microblaze_linux.c b/lib_microblaze/microblaze_linux.c
index b3a0815..2c7885c 100644
--- a/lib_microblaze/microblaze_linux.c
+++ b/lib_microblaze/microblaze_linux.c
@@ -1,6 +1,8 @@
/*
+ * (C) Copyright 2007 Michal Simek
* (C) Copyright 2004 Atmark Techno, Inc.
*
+ * Michal SIMEK <monstr@monstr.eu>
* Yasushi SHOJI <yashi@atmark-techno.com>
*
* See file CREDITS for list of people who contributed to this
@@ -13,7 +15,7 @@
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
@@ -24,8 +26,146 @@
#include <common.h>
#include <command.h>
+#include <image.h>
+#include <zlib.h>
+#include <asm/byteorder.h>
-void do_bootm_linux(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[],
- ulong addr, ulong *len_ptr, int verify)
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_SHOW_BOOT_PROGRESS
+# include <status_led.h>
+# define SHOW_BOOT_PROGRESS(arg) show_boot_progress(arg)
+#else
+# define SHOW_BOOT_PROGRESS(arg)
+#endif
+
+extern image_header_t header; /* from cmd_bootm.c */
+/*cmd_boot.c*/
+extern int do_reset (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]);
+
+void do_bootm_linux (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[],
+ ulong addr, ulong * len_ptr, int verify)
{
+ ulong len = 0, checksum;
+ ulong initrd_start, initrd_end;
+ ulong data;
+ /* First parameter is mapped to $r5 for kernel boot args */
+ void (*theKernel) (char *);
+ image_header_t *hdr = &header;
+ char *commandline = getenv ("bootargs");
+ int i;
+
+ theKernel = (void (*)(char *))ntohl (hdr->ih_ep);
+
+ /* Check if there is an initrd image */
+ if (argc >= 3) {
+ SHOW_BOOT_PROGRESS (9);
+
+ addr = simple_strtoul (argv[2], NULL, 16);
+
+ printf ("## Loading Ramdisk Image at %08lx ...\n", addr);
+
+ /* Copy header so we can blank CRC field for re-calculation */
+ memcpy (&header, (char *)addr, sizeof (image_header_t));
+
+ if (ntohl (hdr->ih_magic) != IH_MAGIC) {
+ printf ("Bad Magic Number\n");
+ SHOW_BOOT_PROGRESS (-10);
+ do_reset (cmdtp, flag, argc, argv);
+ }
+
+ data = (ulong) & header;
+ len = sizeof (image_header_t);
+
+ checksum = ntohl (hdr->ih_hcrc);
+ hdr->ih_hcrc = 0;
+
+ if (crc32 (0, (char *)data, len) != checksum) {
+ printf ("Bad Header Checksum\n");
+ SHOW_BOOT_PROGRESS (-11);
+ do_reset (cmdtp, flag, argc, argv);
+ }
+
+ SHOW_BOOT_PROGRESS (10);
+
+ print_image_hdr (hdr);
+
+ data = addr + sizeof (image_header_t);
+ len = ntohl (hdr->ih_size);
+
+ if (verify) {
+ ulong csum = 0;
+
+ printf (" Verifying Checksum ... ");
+ csum = crc32 (0, (char *)data, len);
+ if (csum != ntohl (hdr->ih_dcrc)) {
+ printf ("Bad Data CRC\n");
+ SHOW_BOOT_PROGRESS (-12);
+ do_reset (cmdtp, flag, argc, argv);
+ }
+ printf ("OK\n");
+ }
+
+ SHOW_BOOT_PROGRESS (11);
+
+ if ((hdr->ih_os != IH_OS_LINUX) ||
+ (hdr->ih_arch != IH_CPU_MICROBLAZE) ||
+ (hdr->ih_type != IH_TYPE_RAMDISK)) {
+ printf ("No Linux Microblaze Ramdisk Image\n");
+ SHOW_BOOT_PROGRESS (-13);
+ do_reset (cmdtp, flag, argc, argv);
+ }
+
+ /*
+ * Now check if we have a multifile image
+ */
+ } else if ((hdr->ih_type == IH_TYPE_MULTI) && (len_ptr[1])) {
+ ulong tail = ntohl (len_ptr[0]) % 4;
+
+ SHOW_BOOT_PROGRESS (13);
+
+ /* skip kernel length and terminator */
+ data = (ulong) (&len_ptr[2]);
+ /* skip any additional image length fields */
+ for (i = 1; len_ptr[i]; ++i)
+ data += 4;
+ /* add kernel length, and align */
+ data += ntohl (len_ptr[0]);
+ if (tail) {
+ data += 4 - tail;
+ }
+
+ len = ntohl (len_ptr[1]);
+
+ } else {
+ /*
+ * no initrd image
+ */
+ SHOW_BOOT_PROGRESS (14);
+
+ data = 0;
+ }
+
+#ifdef DEBUG
+ if (!data) {
+ printf ("No initrd\n");
+ }
+#endif
+
+ if (data) {
+ initrd_start = data;
+ initrd_end = initrd_start + len;
+ } else {
+ initrd_start = 0;
+ initrd_end = 0;
+ }
+
+ SHOW_BOOT_PROGRESS (15);
+
+#ifdef DEBUG
+ printf ("## Transferring control to Linux (at address %08lx) ...\n",
+ (ulong) theKernel);
+#endif
+
+ theKernel (commandline);
}
diff --git a/lib_microblaze/time.c b/lib_microblaze/time.c
index 12e8488..3fa1b11 100644
--- a/lib_microblaze/time.c
+++ b/lib_microblaze/time.c
@@ -1,6 +1,8 @@
/*
+ * (C) Copyright 2007 Michal Simek
* (C) Copyright 2004 Atmark Techno, Inc.
*
+ * Michal SIMEK <monstr@monstr.eu>
* Yasushi SHOJI <yashi@atmark-techno.com>
*
* See file CREDITS for list of people who contributed to this
@@ -22,6 +24,11 @@
* MA 02111-1307 USA
*/
-void udelay(unsigned long usec)
+#include <common.h>
+
+void udelay (unsigned long usec)
{
+ int i;
+ i = get_timer (0);
+ while ((get_timer (0) - i) < (usec / 1000)) ;
}
diff --git a/lib_ppc/extable.c b/lib_ppc/extable.c
index d92f142..fe856ff 100644
--- a/lib_ppc/extable.c
+++ b/lib_ppc/extable.c
@@ -37,6 +37,8 @@
* on our cache or tlb entries.
*/
+DECLARE_GLOBAL_DATA_PTR;
+
struct exception_table_entry
{
unsigned long insn, fixup;
@@ -55,10 +57,22 @@
long diff;
mid = (last - first) / 2 + first;
- diff = mid->insn - value;
- if (diff == 0)
- return mid->fixup;
- else if (diff < 0)
+ if (mid > CFG_MONITOR_BASE) {
+ /* exception occurs in FLASH, before u-boot relocation.
+ * No relocation offset is needed.
+ */
+ diff = mid->insn - value;
+ if (diff == 0)
+ return mid->fixup;
+ } else {
+ /* exception occurs in RAM, after u-boot relocation.
+ * A relocation offset should be added.
+ */
+ diff = (mid->insn + gd->reloc_off) - value;
+ if (diff == 0)
+ return (mid->fixup + gd->reloc_off);
+ }
+ if (diff < 0)
first = mid+1;
else
last = mid-1;
@@ -75,8 +89,11 @@
/* There is only the kernel to search. */
ret = search_one_table(__start___ex_table, __stop___ex_table-1, addr);
+ /* if the serial port does not hang in exception, printf can be used */
+#if !defined(CFG_SERIAL_HANG_IN_EXCEPTION)
if (ex_tab_message)
printf("Bus Fault @ 0x%08lx, fixup 0x%08lx\n", addr, ret);
+#endif
if (ret) return ret;
return 0;
diff --git a/libfdt/Makefile b/libfdt/Makefile
new file mode 100644
index 0000000..dc41137
--- /dev/null
+++ b/libfdt/Makefile
@@ -0,0 +1,46 @@
+#
+# (C) Copyright 2000-2007
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)libfdt.a
+
+SOBJS =
+
+COBJS = fdt.o fdt_ro.o fdt_rw.o fdt_strerror.o fdt_sw.o fdt_wip.o
+
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/libfdt/README b/libfdt/README
new file mode 100644
index 0000000..f4cca34
--- /dev/null
+++ b/libfdt/README
@@ -0,0 +1,23 @@
+The libfdt functionality was written by David Gibson. The original
+source came from the git repository:
+
+URL: git://ozlabs.org/home/dgibson/git/libfdt.git
+
+author David Gibson <dgibson@sneetch.(none)>
+ Fri, 23 Mar 2007 04:16:54 +0000 (15:16 +1100)
+committer David Gibson <dgibson@sneetch.(none)>
+ Fri, 23 Mar 2007 04:16:54 +0000 (15:16 +1100)
+commit 857f54e79f74429af20c2b5ecc00ee98af6a3b8b
+tree 2f648f0f88225a51ded452968d28b4402df8ade0
+parent 07a12a08005f3b5cd9337900a6551e450c07b515
+
+To adapt for u-boot usage, only the applicable files were copied and
+imported into the u-boot git repository.
+Omitted:
+* GPL - u-boot comes with a copy of the GPL license
+* test subdirectory - not directly useful for u-boot
+
+After importing, other customizations were performed. See the git log
+for details.
+
+Jerry Van Baren
diff --git a/libfdt/fdt.c b/libfdt/fdt.c
new file mode 100644
index 0000000..4b1c8ab
--- /dev/null
+++ b/libfdt/fdt.c
@@ -0,0 +1,85 @@
+/*
+ * libfdt - Flat Device Tree manipulation
+ * Copyright (C) 2006 David Gibson, IBM Corporation.
+ *
+ * This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU Lesser General Public License
+ * as published by the Free Software Foundation; either version 2.1 of
+ * the License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * Lesser General Public License for more details.
+ *
+ * You should have received a copy of the GNU Lesser General Public
+ * License along with this library; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+#include "libfdt_env.h"
+
+#include <fdt.h>
+#include <libfdt.h>
+
+#include "libfdt_internal.h"
+
+int _fdt_check_header(const void *fdt)
+{
+ if (fdt_magic(fdt) == FDT_MAGIC) {
+ /* Complete tree */
+ if (fdt_version(fdt) < FDT_FIRST_SUPPORTED_VERSION)
+ return -FDT_ERR_BADVERSION;
+ if (fdt_last_comp_version(fdt) > FDT_LAST_SUPPORTED_VERSION)
+ return -FDT_ERR_BADVERSION;
+ } else if (fdt_magic(fdt) == SW_MAGIC) {
+ /* Unfinished sequential-write blob */
+ if (fdt_size_dt_struct(fdt) == 0)
+ return -FDT_ERR_BADSTATE;
+ } else {
+ return -FDT_ERR_BADMAGIC;
+ }
+
+ return 0;
+}
+
+void *fdt_offset_ptr(const void *fdt, int offset, int len)
+{
+ void *p;
+
+ if (fdt_version(fdt) >= 0x11)
+ if (((offset + len) < offset)
+ || ((offset + len) > fdt_size_dt_struct(fdt)))
+ return NULL;
+
+ p = _fdt_offset_ptr(fdt, offset);
+
+ if (p + len < p)
+ return NULL;
+ return p;
+}
+
+const char *_fdt_find_string(const char *strtab, int tabsize, const char *s)
+{
+ int len = strlen(s) + 1;
+ const char *last = strtab + tabsize - len;
+ const char *p;
+
+ for (p = strtab; p <= last; p++)
+ if (memeq(p, s, len))
+ return p;
+ return NULL;
+}
+
+int fdt_move(const void *fdt, void *buf, int bufsize)
+{
+ int err = _fdt_check_header(fdt);
+
+ if (err)
+ return err;
+
+ if (fdt_totalsize(fdt) > bufsize)
+ return -FDT_ERR_NOSPACE;
+
+ memmove(buf, fdt, fdt_totalsize(fdt));
+ return 0;
+}
diff --git a/libfdt/fdt_ro.c b/libfdt/fdt_ro.c
new file mode 100644
index 0000000..ce01dc7
--- /dev/null
+++ b/libfdt/fdt_ro.c
@@ -0,0 +1,331 @@
+/*
+ * libfdt - Flat Device Tree manipulation
+ * Copyright (C) 2006 David Gibson, IBM Corporation.
+ *
+ * This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU Lesser General Public License
+ * as published by the Free Software Foundation; either version 2.1 of
+ * the License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * Lesser General Public License for more details.
+ *
+ * You should have received a copy of the GNU Lesser General Public
+ * License along with this library; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+#include "libfdt_env.h"
+
+#include <fdt.h>
+#include <libfdt.h>
+
+#include "libfdt_internal.h"
+
+#define CHECK_HEADER(fdt) { \
+ int err; \
+ if ((err = _fdt_check_header(fdt)) != 0) \
+ return err; \
+}
+
+static int offset_streq(const void *fdt, int offset,
+ const char *s, int len)
+{
+ const char *p = fdt_offset_ptr(fdt, offset, len+1);
+
+ if (! p)
+ /* short match */
+ return 0;
+
+ if (memcmp(p, s, len) != 0)
+ return 0;
+
+ if (p[len] != '\0')
+ return 0;
+
+ return 1;
+}
+
+/*
+ * Return a pointer to the string at the given string offset.
+ */
+char *fdt_string(const void *fdt, int stroffset)
+{
+ return (char *)fdt + fdt_off_dt_strings(fdt) + stroffset;
+}
+
+/*
+ * Return the node offset of the node specified by:
+ * parentoffset - starting place (0 to start at the root)
+ * name - name being searched for
+ * namelen - length of the name: typically strlen(name)
+ *
+ * Notes:
+ * If the start node has subnodes, the subnodes are _not_ searched for the
+ * requested name.
+ */
+int fdt_subnode_offset_namelen(const void *fdt, int parentoffset,
+ const char *name, int namelen)
+{
+ int level = 0;
+ uint32_t tag;
+ int offset, nextoffset;
+
+ CHECK_HEADER(fdt);
+
+ tag = fdt_next_tag(fdt, parentoffset, &nextoffset, NULL);
+ if (tag != FDT_BEGIN_NODE)
+ return -FDT_ERR_BADOFFSET;
+
+ do {
+ offset = nextoffset;
+ tag = fdt_next_tag(fdt, offset, &nextoffset, NULL);
+
+ switch (tag) {
+ case FDT_END:
+ return -FDT_ERR_TRUNCATED;
+
+ case FDT_BEGIN_NODE:
+ level++;
+ /*
+ * If we are nested down levels, ignore the strings
+ * until we get back to the proper level.
+ */
+ if (level != 1)
+ continue;
+
+ /* Return the offset if this is "our" string. */
+ if (offset_streq(fdt, offset+FDT_TAGSIZE, name, namelen))
+ return offset;
+ break;
+
+ case FDT_END_NODE:
+ level--;
+ break;
+
+ case FDT_PROP:
+ case FDT_NOP:
+ break;
+
+ default:
+ return -FDT_ERR_BADSTRUCTURE;
+ }
+ } while (level >= 0);
+
+ return -FDT_ERR_NOTFOUND;
+}
+
+/*
+ * See fdt_subnode_offset_namelen()
+ */
+int fdt_subnode_offset(const void *fdt, int parentoffset,
+ const char *name)
+{
+ return fdt_subnode_offset_namelen(fdt, parentoffset, name, strlen(name));
+}
+
+/*
+ * Searches for the node corresponding to the given path and returns the
+ * offset of that node.
+ */
+int fdt_path_offset(const void *fdt, const char *path)
+{
+ const char *end = path + strlen(path);
+ const char *p = path;
+ int offset = 0;
+
+ CHECK_HEADER(fdt);
+
+ /* Paths must be absolute */
+ if (*path != '/')
+ return -FDT_ERR_BADPATH;
+
+ while (*p) {
+ const char *q;
+
+ /* Skip path separator(s) */
+ while (*p == '/')
+ p++;
+ if (! *p)
+ return -FDT_ERR_BADPATH;
+
+ /*
+ * Find the next path separator. The characters between
+ * p and q are the next segment of the the path to find.
+ */
+ q = strchr(p, '/');
+ if (! q)
+ q = end;
+
+ /*
+ * Find the offset corresponding to the this path segment.
+ */
+ offset = fdt_subnode_offset_namelen(fdt, offset, p, q-p);
+
+ /* Oops, error, abort abort abort */
+ if (offset < 0)
+ return offset;
+
+ p = q;
+ }
+
+ return offset;
+}
+
+/*
+ * Given the offset of a node and a name of a property in that node, return
+ * a pointer to the property struct.
+ */
+struct fdt_property *fdt_get_property(const void *fdt,
+ int nodeoffset,
+ const char *name, int *lenp)
+{
+ int level = 0;
+ uint32_t tag;
+ struct fdt_property *prop;
+ int namestroff;
+ int offset, nextoffset;
+ int err;
+
+ if ((err = _fdt_check_header(fdt)) != 0)
+ goto fail;
+
+ err = -FDT_ERR_BADOFFSET;
+ if (nodeoffset % FDT_TAGSIZE)
+ goto fail;
+
+ tag = fdt_next_tag(fdt, nodeoffset, &nextoffset, NULL);
+ if (tag != FDT_BEGIN_NODE)
+ goto fail;
+
+ do {
+ offset = nextoffset;
+
+ tag = fdt_next_tag(fdt, offset, &nextoffset, NULL);
+ switch (tag) {
+ case FDT_END:
+ err = -FDT_ERR_TRUNCATED;
+ goto fail;
+
+ case FDT_BEGIN_NODE:
+ level++;
+ break;
+
+ case FDT_END_NODE:
+ level--;
+ break;
+
+ case FDT_PROP:
+ /*
+ * If we are nested down levels, ignore the strings
+ * until we get back to the proper level.
+ */
+ if (level != 0)
+ continue;
+
+ err = -FDT_ERR_BADSTRUCTURE;
+ prop = fdt_offset_ptr_typed(fdt, offset, prop);
+ if (! prop)
+ goto fail;
+ namestroff = fdt32_to_cpu(prop->nameoff);
+ if (streq(fdt_string(fdt, namestroff), name)) {
+ /* Found it! */
+ int len = fdt32_to_cpu(prop->len);
+ prop = fdt_offset_ptr(fdt, offset,
+ sizeof(*prop)+len);
+ if (! prop)
+ goto fail;
+
+ if (lenp)
+ *lenp = len;
+
+ return prop;
+ }
+ break;
+
+ case FDT_NOP:
+ break;
+
+ default:
+ err = -FDT_ERR_BADSTRUCTURE;
+ goto fail;
+ }
+ } while (level >= 0);
+
+ err = -FDT_ERR_NOTFOUND;
+fail:
+ if (lenp)
+ *lenp = err;
+ return NULL;
+}
+
+/*
+ * Given the offset of a node and a name of a property in that node, return
+ * a pointer to the property data (ONLY).
+ */
+void *fdt_getprop(const void *fdt, int nodeoffset,
+ const char *name, int *lenp)
+{
+ const struct fdt_property *prop;
+
+ prop = fdt_get_property(fdt, nodeoffset, name, lenp);
+ if (! prop)
+ return NULL;
+
+ return (void *)prop->data;
+}
+
+
+uint32_t fdt_next_tag(const void *fdt, int offset, int *nextoffset, char **namep)
+{
+ const uint32_t *tagp, *lenp;
+ uint32_t tag;
+ const char *p;
+
+ if (offset % FDT_TAGSIZE)
+ return -1;
+
+ tagp = fdt_offset_ptr(fdt, offset, FDT_TAGSIZE);
+ if (! tagp)
+ return FDT_END; /* premature end */
+ tag = fdt32_to_cpu(*tagp);
+ offset += FDT_TAGSIZE;
+
+ switch (tag) {
+ case FDT_BEGIN_NODE:
+ if(namep)
+ *namep = fdt_offset_ptr(fdt, offset, 1);
+
+ /* skip name */
+ do {
+ p = fdt_offset_ptr(fdt, offset++, 1);
+ } while (p && (*p != '\0'));
+ if (! p)
+ return FDT_END;
+ break;
+ case FDT_PROP:
+ lenp = fdt_offset_ptr(fdt, offset, sizeof(*lenp));
+ if (! lenp)
+ return FDT_END;
+ /*
+ * Get the property and set the namep to the name.
+ */
+ if(namep) {
+ struct fdt_property *prop;
+
+ prop = fdt_offset_ptr_typed(fdt, offset - FDT_TAGSIZE, prop);
+ if (! prop)
+ return -FDT_ERR_BADSTRUCTURE;
+ *namep = fdt_string(fdt, fdt32_to_cpu(prop->nameoff));
+ }
+ /* skip name offset, length and value */
+ offset += 2*FDT_TAGSIZE + fdt32_to_cpu(*lenp);
+ break;
+ }
+
+ if (nextoffset)
+ *nextoffset = ALIGN(offset, FDT_TAGSIZE);
+
+ return tag;
+}
diff --git a/libfdt/fdt_rw.c b/libfdt/fdt_rw.c
new file mode 100644
index 0000000..b33fbf4
--- /dev/null
+++ b/libfdt/fdt_rw.c
@@ -0,0 +1,293 @@
+/*
+ * libfdt - Flat Device Tree manipulation
+ * Copyright (C) 2006 David Gibson, IBM Corporation.
+ *
+ * This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU Lesser General Public License
+ * as published by the Free Software Foundation; either version 2.1 of
+ * the License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * Lesser General Public License for more details.
+ *
+ * You should have received a copy of the GNU Lesser General Public
+ * License along with this library; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+#include "libfdt_env.h"
+
+#include <fdt.h>
+#include <libfdt.h>
+
+#include "libfdt_internal.h"
+
+static int rw_check_header(void *fdt)
+{
+ int err;
+
+ if ((err = _fdt_check_header(fdt)))
+ return err;
+ if (fdt_version(fdt) < 0x11)
+ return -FDT_ERR_BADVERSION;
+ if (fdt_off_mem_rsvmap(fdt) < ALIGN(sizeof(struct fdt_header), 8))
+ return -FDT_ERR_BADLAYOUT;
+ if (fdt_off_dt_struct(fdt) <
+ (fdt_off_mem_rsvmap(fdt) + sizeof(struct fdt_reserve_entry)))
+ return -FDT_ERR_BADLAYOUT;
+ if (fdt_off_dt_strings(fdt) <
+ (fdt_off_dt_struct(fdt) + fdt_size_dt_struct(fdt)))
+ return -FDT_ERR_BADLAYOUT;
+ if (fdt_totalsize(fdt) <
+ (fdt_off_dt_strings(fdt) + fdt_size_dt_strings(fdt)))
+ return -FDT_ERR_BADLAYOUT;
+ return 0;
+}
+
+#define RW_CHECK_HEADER(fdt) \
+ { \
+ int err; \
+ if ((err = rw_check_header(fdt)) != 0) \
+ return err; \
+ }
+
+static inline int _blob_data_size(void *fdt)
+{
+ return fdt_off_dt_strings(fdt) + fdt_size_dt_strings(fdt);
+}
+
+static int _blob_splice(void *fdt, void *p, int oldlen, int newlen)
+{
+ void *end = fdt + _blob_data_size(fdt);
+
+ if (((p + oldlen) < p) || ((p + oldlen) > end))
+ return -FDT_ERR_BADOFFSET;
+ if ((end - oldlen + newlen) > (fdt + fdt_totalsize(fdt)))
+ return -FDT_ERR_NOSPACE;
+ memmove(p + newlen, p + oldlen, end - p - oldlen);
+ return 0;
+}
+
+static int _blob_splice_struct(void *fdt, void *p,
+ int oldlen, int newlen)
+{
+ int delta = newlen - oldlen;
+ int err;
+
+ if ((err = _blob_splice(fdt, p, oldlen, newlen)))
+ return err;
+
+ fdt_set_header(fdt, size_dt_struct, fdt_size_dt_struct(fdt) + delta);
+ fdt_set_header(fdt, off_dt_strings, fdt_off_dt_strings(fdt) + delta);
+ return 0;
+}
+
+static int _blob_splice_string(void *fdt, int newlen)
+{
+ void *p = fdt + fdt_off_dt_strings(fdt) + fdt_size_dt_strings(fdt);
+ int err;
+
+ if ((err = _blob_splice(fdt, p, 0, newlen)))
+ return err;
+
+ fdt_set_header(fdt, size_dt_strings, fdt_size_dt_strings(fdt) + newlen);
+ return 0;
+}
+
+static int _find_add_string(void *fdt, const char *s)
+{
+ char *strtab = (char *)fdt + fdt_off_dt_strings(fdt);
+ const char *p;
+ char *new;
+ int len = strlen(s) + 1;
+ int err;
+
+ p = _fdt_find_string(strtab, fdt_size_dt_strings(fdt), s);
+ if (p)
+ /* found it */
+ return (p - strtab);
+
+ new = strtab + fdt_size_dt_strings(fdt);
+ err = _blob_splice_string(fdt, len);
+ if (err)
+ return err;
+
+ memcpy(new, s, len);
+ return (new - strtab);
+}
+
+static int _resize_property(void *fdt, int nodeoffset, const char *name, int len,
+ struct fdt_property **prop)
+{
+ int oldlen;
+ int err;
+
+ *prop = fdt_get_property(fdt, nodeoffset, name, &oldlen);
+ if (! (*prop))
+ return oldlen;
+
+ if ((err = _blob_splice_struct(fdt, (*prop)->data,
+ ALIGN(oldlen, FDT_TAGSIZE),
+ ALIGN(len, FDT_TAGSIZE))))
+ return err;
+
+ (*prop)->len = cpu_to_fdt32(len);
+ return 0;
+}
+
+static int _add_property(void *fdt, int nodeoffset, const char *name, int len,
+ struct fdt_property **prop)
+{
+ uint32_t tag;
+ int proplen;
+ int nextoffset;
+ int namestroff;
+ int err;
+
+ tag = fdt_next_tag(fdt, nodeoffset, &nextoffset, NULL);
+ if (tag != FDT_BEGIN_NODE)
+ return -FDT_ERR_BADOFFSET;
+
+ namestroff = _find_add_string(fdt, name);
+ if (namestroff < 0)
+ return namestroff;
+
+ *prop = _fdt_offset_ptr(fdt, nextoffset);
+ proplen = sizeof(**prop) + ALIGN(len, FDT_TAGSIZE);
+
+ err = _blob_splice_struct(fdt, *prop, 0, proplen);
+ if (err)
+ return err;
+
+ (*prop)->tag = cpu_to_fdt32(FDT_PROP);
+ (*prop)->nameoff = cpu_to_fdt32(namestroff);
+ (*prop)->len = cpu_to_fdt32(len);
+ return 0;
+}
+
+int fdt_setprop(void *fdt, int nodeoffset, const char *name,
+ const void *val, int len)
+{
+ struct fdt_property *prop;
+ int err;
+
+ if ((err = rw_check_header(fdt)))
+ return err;
+
+ err = _resize_property(fdt, nodeoffset, name, len, &prop);
+ if (err == -FDT_ERR_NOTFOUND)
+ err = _add_property(fdt, nodeoffset, name, len, &prop);
+ if (err)
+ return err;
+
+ memcpy(prop->data, val, len);
+ return 0;
+}
+
+int fdt_delprop(void *fdt, int nodeoffset, const char *name)
+{
+ struct fdt_property *prop;
+ int len, proplen;
+
+ RW_CHECK_HEADER(fdt);
+
+ prop = fdt_get_property(fdt, nodeoffset, name, &len);
+ if (! prop)
+ return len;
+
+ proplen = sizeof(*prop) + ALIGN(len, FDT_TAGSIZE);
+ return _blob_splice_struct(fdt, prop, proplen, 0);
+}
+
+int fdt_add_subnode_namelen(void *fdt, int parentoffset,
+ const char *name, int namelen)
+{
+ struct fdt_node_header *nh;
+ int offset, nextoffset;
+ int nodelen;
+ int err;
+ uint32_t tag;
+ uint32_t *endtag;
+
+ RW_CHECK_HEADER(fdt);
+
+ offset = fdt_subnode_offset_namelen(fdt, parentoffset, name, namelen);
+ if (offset >= 0)
+ return -FDT_ERR_EXISTS;
+ else if (offset != -FDT_ERR_NOTFOUND)
+ return offset;
+
+ /* Try to place the new node after the parent's properties */
+ fdt_next_tag(fdt, parentoffset, &nextoffset, NULL); /* skip the BEGIN_NODE */
+ do {
+ offset = nextoffset;
+ tag = fdt_next_tag(fdt, offset, &nextoffset, NULL);
+ } while (tag == FDT_PROP);
+
+ nh = _fdt_offset_ptr(fdt, offset);
+ nodelen = sizeof(*nh) + ALIGN(namelen+1, FDT_TAGSIZE) + FDT_TAGSIZE;
+
+ err = _blob_splice_struct(fdt, nh, 0, nodelen);
+ if (err)
+ return err;
+
+ nh->tag = cpu_to_fdt32(FDT_BEGIN_NODE);
+ memset(nh->name, 0, ALIGN(namelen+1, FDT_TAGSIZE));
+ memcpy(nh->name, name, namelen);
+ endtag = (uint32_t *)((void *)nh + nodelen - FDT_TAGSIZE);
+ *endtag = cpu_to_fdt32(FDT_END_NODE);
+
+ return offset;
+}
+
+int fdt_add_subnode(void *fdt, int parentoffset, const char *name)
+{
+ return fdt_add_subnode_namelen(fdt, parentoffset, name, strlen(name));
+}
+
+int fdt_del_node(void *fdt, int nodeoffset)
+{
+ int endoffset;
+
+ endoffset = _fdt_node_end_offset(fdt, nodeoffset);
+ if (endoffset < 0)
+ return endoffset;
+
+ return _blob_splice_struct(fdt, _fdt_offset_ptr(fdt, nodeoffset),
+ endoffset - nodeoffset, 0);
+}
+
+int fdt_open_into(void *fdt, void *buf, int bufsize)
+{
+ int err;
+
+ err = fdt_move(fdt, buf, bufsize);
+ if (err)
+ return err;
+
+ fdt = buf;
+
+ fdt_set_header(fdt, totalsize, bufsize);
+
+ /* FIXME: re-order if necessary */
+
+ err = rw_check_header(fdt);
+ if (err)
+ return err;
+
+ return 0;
+}
+
+int fdt_pack(void *fdt)
+{
+ int err;
+
+ err = rw_check_header(fdt);
+ if (err)
+ return err;
+
+ /* FIXME: pack components */
+ fdt_set_header(fdt, totalsize, _blob_data_size(fdt));
+ return 0;
+}
diff --git a/libfdt/fdt_strerror.c b/libfdt/fdt_strerror.c
new file mode 100644
index 0000000..7f231ce
--- /dev/null
+++ b/libfdt/fdt_strerror.c
@@ -0,0 +1,64 @@
+/*
+ * libfdt - Flat Device Tree manipulation
+ * Copyright (C) 2006 David Gibson, IBM Corporation.
+ *
+ * This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU Lesser General Public License
+ * as published by the Free Software Foundation; either version 2.1 of
+ * the License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * Lesser General Public License for more details.
+ *
+ * You should have received a copy of the GNU Lesser General Public
+ * License along with this library; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+#include "libfdt_env.h"
+
+#include <fdt.h>
+#include <libfdt.h>
+
+#include "libfdt_internal.h"
+
+struct errtabent {
+ const char *str;
+};
+
+#define ERRTABENT(val) \
+ [(val)] = { .str = #val, }
+
+static struct errtabent errtable[] = {
+ ERRTABENT(FDT_ERR_NOTFOUND),
+ ERRTABENT(FDT_ERR_EXISTS),
+ ERRTABENT(FDT_ERR_NOSPACE),
+
+ ERRTABENT(FDT_ERR_BADOFFSET),
+ ERRTABENT(FDT_ERR_BADPATH),
+ ERRTABENT(FDT_ERR_BADSTATE),
+
+ ERRTABENT(FDT_ERR_TRUNCATED),
+ ERRTABENT(FDT_ERR_BADMAGIC),
+ ERRTABENT(FDT_ERR_BADVERSION),
+ ERRTABENT(FDT_ERR_BADSTRUCTURE),
+ ERRTABENT(FDT_ERR_BADLAYOUT),
+};
+#define ERRTABSIZE (sizeof(errtable) / sizeof(errtable[0]))
+
+const char *fdt_strerror(int errval)
+{
+ if (errval > 0)
+ return "<valid offset/length>";
+ else if (errval == 0)
+ return "<no error>";
+ else if (errval > -ERRTABSIZE) {
+ const char *s = errtable[-errval].str;
+
+ if (s)
+ return s;
+ }
+
+ return "<unknown error>";
+}
diff --git a/libfdt/fdt_sw.c b/libfdt/fdt_sw.c
new file mode 100644
index 0000000..672f4dd
--- /dev/null
+++ b/libfdt/fdt_sw.c
@@ -0,0 +1,226 @@
+/*
+ * libfdt - Flat Device Tree manipulation
+ * Copyright (C) 2006 David Gibson, IBM Corporation.
+ *
+ * This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU Lesser General Public License
+ * as published by the Free Software Foundation; either version 2.1 of
+ * the License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * Lesser General Public License for more details.
+ *
+ * You should have received a copy of the GNU Lesser General Public
+ * License along with this library; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+#include "libfdt_env.h"
+
+#include <fdt.h>
+#include <libfdt.h>
+
+#include "libfdt_internal.h"
+
+static int check_header_sw(void *fdt)
+{
+ if (fdt_magic(fdt) != SW_MAGIC)
+ return -FDT_ERR_BADMAGIC;
+ return 0;
+}
+
+static void *grab_space(void *fdt, int len)
+{
+ int offset = fdt_size_dt_struct(fdt);
+ int spaceleft;
+
+ spaceleft = fdt_totalsize(fdt) - fdt_off_dt_struct(fdt)
+ - fdt_size_dt_strings(fdt);
+
+ if ((offset + len < offset) || (offset + len > spaceleft))
+ return NULL;
+
+ fdt_set_header(fdt, size_dt_struct, offset + len);
+ return fdt_offset_ptr(fdt, offset, len);
+}
+
+int fdt_create(void *buf, int bufsize)
+{
+ void *fdt = buf;
+
+ if (bufsize < sizeof(struct fdt_header))
+ return -FDT_ERR_NOSPACE;
+
+ memset(buf, 0, bufsize);
+
+ fdt_set_header(fdt, magic, SW_MAGIC);
+ fdt_set_header(fdt, version, FDT_LAST_SUPPORTED_VERSION);
+ fdt_set_header(fdt, last_comp_version, FDT_FIRST_SUPPORTED_VERSION);
+ fdt_set_header(fdt, totalsize, bufsize);
+
+ fdt_set_header(fdt, off_mem_rsvmap, ALIGN(sizeof(struct fdt_header),
+ sizeof(struct fdt_reserve_entry)));
+ fdt_set_header(fdt, off_dt_struct, fdt_off_mem_rsvmap(fdt));
+ fdt_set_header(fdt, off_dt_strings, bufsize);
+
+ return 0;
+}
+
+int fdt_add_reservemap_entry(void *fdt, uint64_t addr, uint64_t size)
+{
+ struct fdt_reserve_entry *re;
+ int err = check_header_sw(fdt);
+ int offset;
+
+ if (err)
+ return err;
+ if (fdt_size_dt_struct(fdt))
+ return -FDT_ERR_BADSTATE;
+
+ offset = fdt_off_dt_struct(fdt);
+ if ((offset + sizeof(*re)) > fdt_totalsize(fdt))
+ return -FDT_ERR_NOSPACE;
+
+ re = (struct fdt_reserve_entry *)((void *)fdt + offset);
+ re->address = cpu_to_fdt64(addr);
+ re->size = cpu_to_fdt64(size);
+
+ fdt_set_header(fdt, off_dt_struct, offset + sizeof(*re));
+
+ return 0;
+}
+
+int fdt_finish_reservemap(void *fdt)
+{
+ return fdt_add_reservemap_entry(fdt, 0, 0);
+}
+
+int fdt_begin_node(void *fdt, const char *name)
+{
+ struct fdt_node_header *nh;
+ int err = check_header_sw(fdt);
+ int namelen = strlen(name) + 1;
+
+ if (err)
+ return err;
+
+ nh = grab_space(fdt, sizeof(*nh) + ALIGN(namelen, FDT_TAGSIZE));
+ if (! nh)
+ return -FDT_ERR_NOSPACE;
+
+ nh->tag = cpu_to_fdt32(FDT_BEGIN_NODE);
+ memcpy(nh->name, name, namelen);
+ return 0;
+}
+
+int fdt_end_node(void *fdt)
+{
+ uint32_t *en;
+ int err = check_header_sw(fdt);
+
+ if (err)
+ return err;
+
+ en = grab_space(fdt, FDT_TAGSIZE);
+ if (! en)
+ return -FDT_ERR_NOSPACE;
+
+ *en = cpu_to_fdt32(FDT_END_NODE);
+ return 0;
+}
+
+static int find_add_string(void *fdt, const char *s)
+{
+ char *strtab = (char *)fdt + fdt_totalsize(fdt);
+ const char *p;
+ int strtabsize = fdt_size_dt_strings(fdt);
+ int len = strlen(s) + 1;
+ int struct_top, offset;
+
+ p = _fdt_find_string(strtab - strtabsize, strtabsize, s);
+ if (p)
+ return p - strtab;
+
+ /* Add it */
+ offset = -strtabsize - len;
+ struct_top = fdt_off_dt_struct(fdt) + fdt_size_dt_struct(fdt);
+ if (fdt_totalsize(fdt) + offset < struct_top)
+ return 0; /* no more room :( */
+
+ memcpy(strtab + offset, s, len);
+ fdt_set_header(fdt, size_dt_strings, strtabsize + len);
+ return offset;
+}
+
+int fdt_property(void *fdt, const char *name, const void *val, int len)
+{
+ struct fdt_property *prop;
+ int err = check_header_sw(fdt);
+ int nameoff;
+
+ if (err)
+ return err;
+
+ nameoff = find_add_string(fdt, name);
+ if (nameoff == 0)
+ return -FDT_ERR_NOSPACE;
+
+ prop = grab_space(fdt, sizeof(*prop) + ALIGN(len, FDT_TAGSIZE));
+ if (! prop)
+ return -FDT_ERR_NOSPACE;
+
+ prop->tag = cpu_to_fdt32(FDT_PROP);
+ prop->nameoff = cpu_to_fdt32(nameoff);
+ prop->len = cpu_to_fdt32(len);
+ memcpy(prop->data, val, len);
+ return 0;
+}
+
+int fdt_finish(void *fdt)
+{
+ int err = check_header_sw(fdt);
+ char *p = (char *)fdt;
+ uint32_t *end;
+ int oldstroffset, newstroffset;
+ uint32_t tag;
+ int offset, nextoffset;
+
+ if (err)
+ return err;
+
+ /* Add terminator */
+ end = grab_space(fdt, sizeof(*end));
+ if (! end)
+ return -FDT_ERR_NOSPACE;
+ *end = cpu_to_fdt32(FDT_END);
+
+ /* Relocate the string table */
+ oldstroffset = fdt_totalsize(fdt) - fdt_size_dt_strings(fdt);
+ newstroffset = fdt_off_dt_struct(fdt) + fdt_size_dt_struct(fdt);
+ memmove(p + newstroffset, p + oldstroffset, fdt_size_dt_strings(fdt));
+ fdt_set_header(fdt, off_dt_strings, newstroffset);
+
+ /* Walk the structure, correcting string offsets */
+ offset = 0;
+ while ((tag = fdt_next_tag(fdt, offset, &nextoffset, NULL)) != FDT_END) {
+ if (tag == FDT_PROP) {
+ struct fdt_property *prop = fdt_offset_ptr(fdt, offset,
+ sizeof(*prop));
+ int nameoff;
+
+ if (! prop)
+ return -FDT_ERR_BADSTRUCTURE;
+
+ nameoff = fdt32_to_cpu(prop->nameoff);
+ nameoff += fdt_size_dt_strings(fdt);
+ prop->nameoff = cpu_to_fdt32(nameoff);
+ }
+ offset = nextoffset;
+ }
+
+ /* Finally, adjust the header */
+ fdt_set_header(fdt, totalsize, newstroffset + fdt_size_dt_strings(fdt));
+ fdt_set_header(fdt, magic, FDT_MAGIC);
+ return 0;
+}
diff --git a/libfdt/fdt_wip.c b/libfdt/fdt_wip.c
new file mode 100644
index 0000000..261b9b0
--- /dev/null
+++ b/libfdt/fdt_wip.c
@@ -0,0 +1,112 @@
+/*
+ * libfdt - Flat Device Tree manipulation
+ * Copyright (C) 2006 David Gibson, IBM Corporation.
+ *
+ * This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU Lesser General Public License
+ * as published by the Free Software Foundation; either version 2.1 of
+ * the License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * Lesser General Public License for more details.
+ *
+ * You should have received a copy of the GNU Lesser General Public
+ * License along with this library; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+#include "libfdt_env.h"
+
+#include <fdt.h>
+#include <libfdt.h>
+
+#include "libfdt_internal.h"
+
+int fdt_setprop_inplace(void *fdt, int nodeoffset, const char *name,
+ const void *val, int len)
+{
+ void *propval;
+ int proplen;
+
+ propval = fdt_getprop(fdt, nodeoffset, name, &proplen);
+ if (! propval)
+ return proplen;
+
+ if (proplen != len)
+ return -FDT_ERR_NOSPACE;
+
+ memcpy(propval, val, len);
+ return 0;
+}
+
+static void nop_region(void *start, int len)
+{
+ uint32_t *p;
+
+ for (p = start; (void *)p < (start + len); p++)
+ *p = cpu_to_fdt32(FDT_NOP);
+}
+
+int fdt_nop_property(void *fdt, int nodeoffset, const char *name)
+{
+ struct fdt_property *prop;
+ int len;
+
+ prop = fdt_get_property(fdt, nodeoffset, name, &len);
+ if (! prop)
+ return len;
+
+ nop_region(prop, len + sizeof(*prop));
+
+ return 0;
+}
+
+int _fdt_node_end_offset(void *fdt, int nodeoffset)
+{
+ int level = 0;
+ uint32_t tag;
+ int offset, nextoffset;
+
+ tag = fdt_next_tag(fdt, nodeoffset, &nextoffset, NULL);
+ if (tag != FDT_BEGIN_NODE)
+ return -FDT_ERR_BADOFFSET;
+ do {
+ offset = nextoffset;
+ tag = fdt_next_tag(fdt, offset, &nextoffset, NULL);
+
+ switch (tag) {
+ case FDT_END:
+ return offset;
+
+ case FDT_BEGIN_NODE:
+ level++;
+ break;
+
+ case FDT_END_NODE:
+ level--;
+ break;
+
+ case FDT_PROP:
+ case FDT_NOP:
+ break;
+
+ default:
+ return -FDT_ERR_BADSTRUCTURE;
+ }
+ } while (level >= 0);
+
+ return nextoffset;
+}
+
+int fdt_nop_node(void *fdt, int nodeoffset)
+{
+ int endoffset;
+
+ endoffset = _fdt_node_end_offset(fdt, nodeoffset);
+ if (endoffset < 0)
+ return endoffset;
+
+ nop_region(fdt_offset_ptr(fdt, nodeoffset, 0), endoffset - nodeoffset);
+ return 0;
+}
diff --git a/libfdt/libfdt_internal.h b/libfdt/libfdt_internal.h
new file mode 100644
index 0000000..cc9633c
--- /dev/null
+++ b/libfdt/libfdt_internal.h
@@ -0,0 +1,40 @@
+#ifndef _LIBFDT_INTERNAL_H
+#define _LIBFDT_INTERNAL_H
+/*
+ * libfdt - Flat Device Tree manipulation
+ * Copyright (C) 2006 David Gibson, IBM Corporation.
+ *
+ * This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU Lesser General Public License
+ * as published by the Free Software Foundation; either version 2.1 of
+ * the License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * Lesser General Public License for more details.
+ *
+ * You should have received a copy of the GNU Lesser General Public
+ * License along with this library; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+#include <fdt.h>
+
+#define ALIGN(x, a) (((x) + (a) - 1) & ~((a) - 1))
+#define PALIGN(p, a) ((void *)ALIGN((unsigned long)(p), (a)))
+
+#define memeq(p, q, n) (memcmp((p), (q), (n)) == 0)
+#define streq(p, q) (strcmp((p), (q)) == 0)
+
+int _fdt_check_header(const void *fdt);
+const char *_fdt_find_string(const char *strtab, int tabsize, const char *s);
+int _fdt_node_end_offset(void *fdt, int nodeoffset);
+
+static inline void *_fdt_offset_ptr(const struct fdt_header *fdt, int offset)
+{
+ return (void *)fdt + fdt_off_dt_struct(fdt) + offset;
+}
+
+#define SW_MAGIC (~FDT_MAGIC)
+
+#endif /* _LIBFDT_INTERNAL_H */
diff --git a/microblaze_config.mk b/microblaze_config.mk
index b3ac8e0..06ddefa 100644
--- a/microblaze_config.mk
+++ b/microblaze_config.mk
@@ -22,7 +22,7 @@
# MA 02111-1307 USA
#
-PLATFORM_CPPFLAGS += -ffixed-r31
+PLATFORM_CPPFLAGS += -ffixed-r31 -D__microblaze__
ifdef CONFIG_MICROBLAZE_HARD_MULT
PLATFORM_CPPFLAGS += -mno-xl-soft-mul
diff --git a/net/eth.c b/net/eth.c
index cca9392..0fc2211 100644
--- a/net/eth.c
+++ b/net/eth.c
@@ -52,9 +52,12 @@
extern int rtl8169_initialize(bd_t*);
extern int scc_initialize(bd_t*);
extern int skge_initialize(bd_t*);
+extern int tsi108_eth_initialize(bd_t*);
extern int tsec_initialize(bd_t*, int, char *);
extern int npe_initialize(bd_t *);
extern int uec_initialize(int);
+extern int bfin_EMAC_initialize(bd_t *);
+extern int atstk1000_eth_initialize(bd_t *);
static struct eth_device *eth_devices, *eth_current;
@@ -249,12 +252,21 @@
#ifdef CONFIG_NS8382X
ns8382x_initialize(bis);
#endif
+#if defined(CONFIG_TSI108_ETH)
+ tsi108_eth_initialize(bis);
+#endif
#if defined(CONFIG_RTL8139)
rtl8139_initialize(bis);
#endif
#if defined(CONFIG_RTL8169)
rtl8169_initialize(bis);
#endif
+#if defined(CONFIG_BF537)
+ bfin_EMAC_initialize(bis);
+#endif
+#if defined(CONFIG_ATSTK1000)
+ atstk1000_eth_initialize(bis);
+#endif
if (!eth_devices) {
puts ("No ethernet found.\n");
diff --git a/net/net.c b/net/net.c
index 1d1c98f..2ff7bfc 100644
--- a/net/net.c
+++ b/net/net.c
@@ -1424,6 +1424,26 @@
/* XXX point to ip packet */
(*packetHandler)((uchar *)ip, 0, 0, 0);
return;
+ case ICMP_ECHO_REQUEST:
+#ifdef ET_DEBUG
+ printf ("Got ICMP ECHO REQUEST, return %d bytes \n",
+ ETHER_HDR_SIZE + len);
+#endif
+ memcpy (&et->et_dest[0], &et->et_src[0], 6);
+ memcpy (&et->et_src[ 0], NetOurEther, 6);
+
+ ip->ip_sum = 0;
+ ip->ip_off = 0;
+ NetCopyIP((void*)&ip->ip_dst, &ip->ip_src);
+ NetCopyIP((void*)&ip->ip_src, &NetOurIP);
+ ip->ip_sum = ~NetCksum((uchar *)ip, IP_HDR_SIZE_NO_UDP >> 1);
+
+ icmph->type = ICMP_ECHO_REPLY;
+ icmph->checksum = 0;
+ icmph->checksum = ~NetCksum((uchar *)icmph,
+ (len - IP_HDR_SIZE_NO_UDP) >> 1);
+ (void) eth_send((uchar *)et, ETHER_HDR_SIZE + len);
+ return;
#endif
default:
return;