net: Add support for ADI SC5xx SoCs with DWC QoS ethernet
The ADI SC598 includes a Designware QoS 5.20a IP block. This
commit adds support for using the existing ethernet QoS driver
with the SC598 SoC.
Co-developed-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Co-developed-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Signed-off-by: Greg Malysa <malysagreg@gmail.com>
diff --git a/drivers/net/dwc_eth_qos_adi.c b/drivers/net/dwc_eth_qos_adi.c
new file mode 100644
index 0000000..0e6a901
--- /dev/null
+++ b/drivers/net/dwc_eth_qos_adi.c
@@ -0,0 +1,103 @@
+// SPDX-License-Identifier: GPL-2.0
+/**
+ * (C) Copyright 2024 - Analog Devices, Inc.
+ *
+ * Written and/or maintained by Timesys Corporation
+ *
+ * Author: Greg Malysa <greg.malysa@timesys.com>
+ * Additional Contact: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
+ */
+
+#include <clk.h>
+#include <dm.h>
+#include <net.h>
+#include <phy.h>
+#include <reset.h>
+#include <linux/io.h>
+
+#include <asm/arch-adi/sc5xx/sc5xx.h>
+
+#include "dwc_eth_qos.h"
+
+static int eqos_start_resets_adi(struct udevice *dev)
+{
+ struct eqos_priv *eqos = dev_get_priv(dev);
+
+ /*
+ * Settings need to latch with the DMA reset below. Currently only
+ * rgmii is supported but other phy interfaces may be supported in
+ * the future
+ */
+ sc5xx_enable_rgmii();
+ setbits_32(&eqos->dma_regs->mode, EQOS_DMA_MODE_SWR);
+
+ return 0;
+}
+
+static int eqos_probe_resources_adi(struct udevice *dev)
+{
+ struct eqos_priv *eqos = dev_get_priv(dev);
+ phy_interface_t interface;
+ int ret;
+
+ ret = eqos_get_base_addr_dt(dev);
+ if (ret) {
+ pr_err("eqos_get_base_addr_dt failed: %d\n", ret);
+ return ret;
+ }
+
+ interface = eqos->config->interface(dev);
+ if (interface == PHY_INTERFACE_MODE_NA) {
+ pr_err("Invalid PHY interface\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+/**
+ * rgmii tx clock rate is set to 125 MHz regardless of phy mode, and
+ * by default the internal clock is always connected to 125 MHz. According
+ * to the HRM it is invalid for this clock to have any other speed, so
+ * the hardware won't work anyway if this is wrong.
+ */
+static ulong eqos_get_tick_clk_rate_adi(struct udevice *dev)
+{
+ return 125 * 1000000;
+}
+
+static int eqos_get_enetaddr_adi(struct udevice *dev)
+{
+ struct eth_pdata *pdata = dev_get_plat(dev);
+
+ return eth_env_get_enetaddr("ethaddr", pdata->enetaddr);
+}
+
+static struct eqos_ops eqos_adi_ops = {
+ .eqos_inval_desc = eqos_inval_desc_generic,
+ .eqos_flush_desc = eqos_flush_desc_generic,
+ .eqos_inval_buffer = eqos_inval_buffer_generic,
+ .eqos_flush_buffer = eqos_flush_buffer_generic,
+ .eqos_probe_resources = eqos_probe_resources_adi,
+ .eqos_remove_resources = eqos_null_ops,
+ .eqos_start_resets = eqos_start_resets_adi,
+ .eqos_stop_resets = eqos_null_ops,
+ .eqos_start_clks = eqos_null_ops,
+ .eqos_stop_clks = eqos_null_ops,
+ .eqos_calibrate_pads = eqos_null_ops,
+ .eqos_disable_calibration = eqos_null_ops,
+ .eqos_set_tx_clk_speed = eqos_null_ops,
+ .eqos_get_enetaddr = eqos_get_enetaddr_adi,
+ .eqos_get_tick_clk_rate = eqos_get_tick_clk_rate_adi,
+};
+
+struct eqos_config __maybe_unused eqos_adi_config = {
+ .reg_access_always_ok = true,
+ .mdio_wait = 20,
+ .swr_wait = 50,
+ .config_mac = EQOS_MAC_RXQ_CTRL0_RXQ0EN_ENABLED_DCB,
+ .config_mac_mdio = EQOS_MAC_MDIO_ADDRESS_CR_150_250,
+ .axi_bus_width = EQOS_AXI_WIDTH_32,
+ .interface = dev_read_phy_mode,
+ .ops = &eqos_adi_ops,
+};