ARM: dts: sun8i: Update A83T dts(i) files from Linux-v4.18-rc3
Update all A83T devicetree dtsi and dtsi files from Linux-v4.18-rc3
with below commit:
commit 221cb9fd2ee3042689fe0e6613d0f34eb46a5af6
Author: Mylène Josserand <mylene.josserand@bootlin.com>
Date: Fri May 4 21:05:44 2018 +0200
ARM: dts: sun8i: Add enable-method for SMP support for the A83T SoC
Note: bananapi-m3 and cubietruck-plus board dts files has
usb_otg enabled in U-Boot which were not present in Linux.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
diff --git a/arch/arm/dts/axp81x.dtsi b/arch/arm/dts/axp81x.dtsi
new file mode 100644
index 0000000..043c717
--- /dev/null
+++ b/arch/arm/dts/axp81x.dtsi
@@ -0,0 +1,169 @@
+/*
+ * Copyright 2017 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/* AXP813/818 Integrated Power Management Chip */
+
+&axp81x {
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ axp_adc: adc {
+ compatible = "x-powers,axp813-adc";
+ #io-channel-cells = <1>;
+ };
+
+ axp_gpio: gpio {
+ compatible = "x-powers,axp813-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio0_ldo: gpio0-ldo {
+ pins = "GPIO0";
+ function = "ldo";
+ };
+
+ gpio1_ldo: gpio1-ldo {
+ pins = "GPIO1";
+ function = "ldo";
+ };
+ };
+
+ battery_power_supply: battery-power-supply {
+ compatible = "x-powers,axp813-battery-power-supply";
+ status = "disabled";
+ };
+
+ regulators {
+ /* Default work frequency for buck regulators */
+ x-powers,dcdc-freq = <3000>;
+
+ reg_dcdc1: dcdc1 {
+ };
+
+ reg_dcdc2: dcdc2 {
+ };
+
+ reg_dcdc3: dcdc3 {
+ };
+
+ reg_dcdc4: dcdc4 {
+ };
+
+ reg_dcdc5: dcdc5 {
+ };
+
+ reg_dcdc6: dcdc6 {
+ };
+
+ reg_dcdc7: dcdc7 {
+ };
+
+ reg_aldo1: aldo1 {
+ };
+
+ reg_aldo2: aldo2 {
+ };
+
+ reg_aldo3: aldo3 {
+ };
+
+ reg_dldo1: dldo1 {
+ };
+
+ reg_dldo2: dldo2 {
+ };
+
+ reg_dldo3: dldo3 {
+ };
+
+ reg_dldo4: dldo4 {
+ };
+
+ reg_eldo1: eldo1 {
+ };
+
+ reg_eldo2: eldo2 {
+ };
+
+ reg_eldo3: eldo3 {
+ };
+
+ reg_fldo1: fldo1 {
+ };
+
+ reg_fldo2: fldo2 {
+ };
+
+ reg_fldo3: fldo3 {
+ };
+
+ reg_ldo_io0: ldo-io0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio0_ldo>;
+ /* Disable by default to avoid conflicts with GPIO */
+ status = "disabled";
+ };
+
+ reg_ldo_io1: ldo-io1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio1_ldo>;
+ /* Disable by default to avoid conflicts with GPIO */
+ status = "disabled";
+ };
+
+ reg_rtc_ldo: rtc-ldo {
+ /* RTC_LDO is a fixed, always-on regulator */
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ reg_sw: sw {
+ };
+
+ reg_drivevbus: drivevbus {
+ status = "disabled";
+ };
+ };
+};
diff --git a/arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts b/arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts
index c8495d7..36eceba 100644
--- a/arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts
+++ b/arch/arm/dts/sun8i-a83t-allwinner-h8homlet-v2.dts
@@ -44,6 +44,8 @@
/dts-v1/;
#include "sun8i-a83t.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
/ {
model = "Allwinner A83T H8Homlet Proto Dev Board v2.0";
compatible = "allwinner,h8homlet-v2", "allwinner,sun8i-a83t";
@@ -55,22 +57,213 @@
chosen {
stdout-path = "serial0:115200n8";
};
+
+ reg_usb0_vbus: reg-usb0-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb0-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* PL5 */
+ };
+
+ reg_usb1_vbus: reg-usb1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+ };
};
&ehci0 {
status = "okay";
};
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ vmmc-supply = <®_dcdc1>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ bus-width = <4>;
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_emmc_pins>;
+ vmmc-supply = <®_dcdc1>;
+ vqmmc-supply = <®_dcdc1>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
&ohci0 {
status = "okay";
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp81x: pmic@3a3 {
+ compatible = "x-powers,axp818", "x-powers,axp813";
+ reg = <0x3a3>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ eldoin-supply = <®_dcdc1>;
+ swin-supply = <®_dcdc1>;
+ };
+
+ ac100: codec@e89 {
+ compatible = "x-powers,ac100";
+ reg = <0xe89>;
+
+ ac100_codec: codec {
+ compatible = "x-powers,ac100-codec";
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 11 IRQ_TYPE_LEVEL_LOW>; /* PL11 */
+ #clock-cells = <0>;
+ clock-output-names = "4M_adda";
+ };
+
+ ac100_rtc: rtc {
+ compatible = "x-powers,ac100-rtc";
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&ac100_codec>;
+ #clock-cells = <1>;
+ clock-output-names = "cko1_rtc",
+ "cko2_rtc",
+ "cko3_rtc";
+ };
+ };
+};
+
+#include "axp81x.dtsi"
+
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-1v8";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "dram-pll";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpua";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpub";
+};
+
+®_dcdc4 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dcdc6 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-mipi";
+};
+
+®_dldo4 {
+ /*
+ * The PHY requires 20ms after all voltages are applied until core
+ * logic is ready and 30ms after the reset pin is de-asserted.
+ * Set a 100ms delay to account for PMIC ramp time and board traces.
+ */
+ regulator-enable-ramp-delay = <100000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-ephy";
+};
+
+®_fldo1 {
+ regulator-min-microvolt = <1080000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd12-hsic";
+};
+
+®_fldo2 {
+ /*
+ * Despite the embedded CPUs core not being used in any way,
+ * this must remain on or the system will hang.
+ */
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus";
};
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
+®_sw {
+ regulator-name = "vcc-wifi";
+};
+
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_b>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
+&usbphy {
+ usb0_vbus-supply = <®_usb0_vbus>;
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
+
&usb_otg {
+ dr_mode = "host";
status = "okay";
};
diff --git a/arch/arm/dts/sun8i-a83t-bananapi-m3.dts b/arch/arm/dts/sun8i-a83t-bananapi-m3.dts
index dfc16a0..eaff6fa 100644
--- a/arch/arm/dts/sun8i-a83t-bananapi-m3.dts
+++ b/arch/arm/dts/sun8i-a83t-bananapi-m3.dts
@@ -1,6 +1,7 @@
/*
- * Copyright 2015 Vishnu Patekar
- * Vishnu Patekar <vishnupatekar0510@gmail.com>
+ * Copyright 2017 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens@csie.org>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
@@ -44,29 +45,316 @@
/dts-v1/;
#include "sun8i-a83t.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
/ {
- model = "Allwinner A83T BananaPi M3 Board v1.2";
- compatible = "bananapi,m3v1.2", "allwinner,sun8i-a83t";
+ model = "Banana Pi BPI-M3";
+ compatible = "sinovoip,bpi-m3", "allwinner,sun8i-a83t";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
+
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ blue {
+ label = "bananapi-m3:blue:usr";
+ gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ green {
+ label = "bananapi-m3:green:usr";
+ gpios = <&axp_gpio 0 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ reg_usb1_vbus: reg-usb1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&ac100_rtc 1>;
+ clock-names = "ext_clock";
+ /* The WiFi low power clock must be 32768 Hz */
+ assigned-clocks = <&ac100_rtc 1>;
+ assigned-clock-rates = <32768>;
+ /* enables internal regulator and de-asserts reset */
+ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
+ };
+};
+
+&de {
+ status = "okay";
};
&ehci0 {
+ /* Terminus Tech FE 1.1s 4-port USB 2.0 hub here */
status = "okay";
+
+ /* TODO GL830 USB-to-SATA bridge downstream w/ GPIO power controls */
};
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_sw>;
+ phy-handle = <&rgmii_phy>;
+ phy-mode = "rgmii";
+ allwinner,rx-delay-ps = <700>;
+ allwinner,tx-delay-ps = <700>;
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&mdio {
+ rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+&mmc1 {
+ vmmc-supply = <®_dldo1>;
+ vqmmc-supply = <®_dldo1>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-names = "host-wake";
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_emmc_pins>;
+ vmmc-supply = <®_dcdc1>;
+ vqmmc-supply = <®_dcdc1>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp81x: pmic@3a3 {
+ compatible = "x-powers,axp813";
+ reg = <0x3a3>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ eldoin-supply = <®_dcdc1>;
+ fldoin-supply = <®_dcdc5>;
+ swin-supply = <®_dcdc1>;
+ x-powers,drive-vbus-en;
+ };
+
+ ac100: codec@e89 {
+ compatible = "x-powers,ac100";
+ reg = <0xe89>;
+
+ ac100_codec: codec {
+ compatible = "x-powers,ac100-codec";
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 11 IRQ_TYPE_LEVEL_LOW>; /* PL11 */
+ #clock-cells = <0>;
+ clock-output-names = "4M_adda";
+ };
+
+ ac100_rtc: rtc {
+ compatible = "x-powers,ac100-rtc";
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&ac100_codec>;
+ #clock-cells = <1>;
+ clock-output-names = "cko1_rtc",
+ "cko2_rtc",
+ "cko3_rtc";
+ };
+ };
+};
+
+#include "axp81x.dtsi"
+
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-1v8";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "dram-pll";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_dcdc1 {
+ /* schematics says 3.1V but FEX file says 3.3V */
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpua";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpub";
+};
+
+®_dcdc4 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dcdc6 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dldo1 {
+ /*
+ * This powers both the WiFi/BT module's main power, I/O supply,
+ * and external pull-ups on all the data lines. It should be set
+ * to the same voltage as the I/O supply (DCDC1 in this case) to
+ * avoid any leakage or mismatch.
+ */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_dldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-name = "vcc-pd";
+};
+
+®_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
+®_fldo1 {
+ regulator-min-microvolt = <1080000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd12-hsic";
+};
+
+®_fldo2 {
+ /*
+ * Despite the embedded CPUs core not being used in any way,
+ * this must remain on or the system will hang.
+ */
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
+®_sw {
+ /*
+ * The PHY requires 20ms after all voltages
+ * are applied until core logic is ready and
+ * 30ms after the reset pin is de-asserted.
+ * Set a 100ms delay to account for PMIC
+ * ramp time and board traces.
+ */
+ regulator-enable-ramp-delay = <100000>;
+ regulator-name = "vcc-ephy";
+};
+
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_b>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&usb_otg {
status = "okay";
};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts b/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts
index 8437c8f..5dba4fc 100644
--- a/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts
+++ b/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts
@@ -45,33 +45,353 @@
/dts-v1/;
#include "sun8i-a83t.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
/ {
model = "Cubietech Cubietruck Plus";
compatible = "cubietech,cubietruck-plus", "allwinner,sun8i-a83t";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
+
+ leds {
+ compatible = "gpio-leds";
+
+ blue {
+ label = "cubietruck-plus:blue:usr";
+ gpios = <&pio 3 25 GPIO_ACTIVE_HIGH>; /* PD25 */
+ };
+
+ orange {
+ label = "cubietruck-plus:orange:usr";
+ gpios = <&pio 3 26 GPIO_ACTIVE_HIGH>; /* PD26 */
+ };
+
+ white {
+ label = "cubietruck-plus:white:usr";
+ gpios = <&pio 3 27 GPIO_ACTIVE_HIGH>; /* PD27 */
+ };
+
+ green {
+ label = "cubietruck-plus:green:usr";
+ gpios = <&pio 4 4 GPIO_ACTIVE_HIGH>; /* PE4 */
+ };
+ };
+
+ usb-hub {
+ /* I2C is not connected */
+ compatible = "smsc,usb3503";
+ initial-mode = <1>; /* initialize in HUB mode */
+ disabled-ports = <1>;
+ intn-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+ reset-gpios = <&pio 4 16 GPIO_ACTIVE_HIGH>; /* PE16 */
+ connect-gpios = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
+ refclk-frequency = <19200000>;
+ };
+
+ reg_usb1_vbus: reg-usb1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&pio 3 29 GPIO_ACTIVE_HIGH>; /* PD29 */
+ };
+
+ reg_usb2_vbus: reg-usb2-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb2-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "On-board SPDIF";
+
+ simple-audio-card,cpu {
+ sound-dai = <&spdif>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&spdif_out>;
+ };
+ };
+
+ spdif_out: spdif-out {
+ #sound-dai-cells = <0>;
+ compatible = "linux,spdif-dit";
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&ac100_rtc 1>;
+ clock-names = "ext_clock";
+ /* The WiFi low power clock must be 32768 Hz */
+ assigned-clocks = <&ac100_rtc 1>;
+ assigned-clock-rates = <32768>;
+ /* enables internal regulator and de-asserts reset */
+ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
+ };
};
&ehci0 {
+ /* GL830 USB-to-SATA bridge here */
status = "okay";
};
&ehci1 {
+ /* USB3503 HSIC USB 2.0 hub here */
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_dldo4>;
+ phy-handle = <&rgmii_phy>;
+ phy-mode = "rgmii";
+ status = "okay";
+};
+
+&mdio {
+ rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+&mmc1 {
+ vmmc-supply = <®_dcdc1>;
+ vqmmc-supply = <®_sw>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_emmc_pins>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp81x: pmic@3a3 {
+ compatible = "x-powers,axp818", "x-powers,axp813";
+ reg = <0x3a3>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ eldoin-supply = <®_dcdc1>;
+ swin-supply = <®_dcdc1>;
+ x-powers,drive-vbus-en;
+ };
+
+ ac100: codec@e89 {
+ compatible = "x-powers,ac100";
+ reg = <0xe89>;
+
+ ac100_codec: codec {
+ compatible = "x-powers,ac100-codec";
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 11 IRQ_TYPE_LEVEL_LOW>; /* PL11 */
+ #clock-cells = <0>;
+ clock-output-names = "4M_adda";
+ };
+
+ ac100_rtc: rtc {
+ compatible = "x-powers,ac100-rtc";
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&ac100_codec>;
+ #clock-cells = <1>;
+ clock-output-names = "cko1_rtc",
+ "cko2_rtc",
+ "cko3_rtc";
+ };
+ };
+};
+
+#include "axp81x.dtsi"
+
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-1v8";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "dram-pll";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_dcdc1 {
+ /*
+ * The schematics say this should be 3.3V, but the FEX file says
+ * it should be 3V. The latter makes sense, as the WiFi module's
+ * I/O is indirectly powered from DCDC1, through SW. It is rated
+ * at 2.98V maximum.
+ */
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpua";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpub";
+};
+
+®_dcdc4 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dcdc6 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "dp-pwr";
+};
+
+®_dldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-name = "ephy-io";
+};
+
+®_dldo4 {
+ /*
+ * The PHY requires 20ms after all voltages are applied until core
+ * logic is ready and 30ms after the reset pin is de-asserted.
+ * Set a 100ms delay to account for PMIC ramp time and board traces.
+ */
+ regulator-enable-ramp-delay = <100000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "ephy";
+};
+
+®_drivevbus {
+ regulator-name = "usb0-vbus";
status = "okay";
};
+®_eldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "dp-bridge-1";
+};
+
+®_eldo2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "dp-bridge-2";
+};
+
+®_fldo1 {
+ /* TODO should be handled by USB PHY */
+ regulator-always-on;
+ regulator-min-microvolt = <1080000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd12-hsic";
+};
+
+®_fldo2 {
+ /*
+ * Despite the embedded CPUs core not being used in any way,
+ * this must remain on or the system will hang.
+ */
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
+®_sw {
+ regulator-name = "vcc-wifi-io";
+};
+
+&spdif {
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_b>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&usb_otg {
status = "okay";
};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/sun8i-a83t-tbs-a711.dts b/arch/arm/dts/sun8i-a83t-tbs-a711.dts
index 80e8b1c..1537ce1 100644
--- a/arch/arm/dts/sun8i-a83t-tbs-a711.dts
+++ b/arch/arm/dts/sun8i-a83t-tbs-a711.dts
@@ -1,6 +1,6 @@
/*
- * Copyright 2017 Ondřej Jirman
- * Ondřej Jirman <megous@megous.com>
+ * Copyright (C) 2017 Touchless Biometric Systems AG
+ * Tomas Novotny <tomas@novotny.cz>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
@@ -44,33 +44,380 @@
/dts-v1/;
#include "sun8i-a83t.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
+
/ {
model = "TBS A711 Tablet";
compatible = "tbs-biometrics,a711", "allwinner,sun8i-a83t";
aliases {
serial0 = &uart0;
+ serial1 = &uart1;
};
chosen {
stdout-path = "serial0:115200n8";
};
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ enable-gpios = <&pio 3 29 GPIO_ACTIVE_HIGH>;
+
+ brightness-levels = <0 1 2 4 8 16 32 64 128 255>;
+ default-brightness-level = <9>;
+ };
+
+ panel {
+ compatible = "tbs,a711-panel", "panel-lvds";
+ backlight = <&backlight>;
+ power-supply = <®_sw>;
+
+ width-mm = <153>;
+ height-mm = <90>;
+ data-mapping = "vesa-24";
+
+ panel-timing {
+ /* 1024x600 @60Hz */
+ clock-frequency = <52000000>;
+ hactive = <1024>;
+ vactive = <600>;
+ hsync-len = <20>;
+ hfront-porch = <180>;
+ hback-porch = <160>;
+ vfront-porch = <12>;
+ vback-porch = <23>;
+ vsync-len = <5>;
+ };
+
+ port {
+ panel_input: endpoint {
+ remote-endpoint = <&tcon0_out_lcd>;
+ };
+ };
+ };
+
+ reg_vbat: reg-vbat {
+ compatible = "regulator-fixed";
+ regulator-name = "vbat";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ };
+
+ reg_vmain: reg-vmain {
+ compatible = "regulator-fixed";
+ regulator-name = "vmain";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <®_vbat>;
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
+
+ /*
+ * This is actually Bluetooth's clock, but we have to
+ * hook it up somewheere
+ */
+ clocks = <&ac100_rtc 1>;
+ clock-names = "ext_clock";
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&cpu100 {
+ cpu-supply = <®_dcdc3>;
+};
+
+&de {
+ status = "okay";
};
+/*
+ * An USB-2 hub is connected here, which also means we don't need to
+ * enable the OHCI controller.
+ */
&ehci0 {
status = "okay";
};
+/*
+ * There's a modem connected here that needs to be initialised before
+ * being able to be enumerated.
+ */
+&ehci1 {
+ status = "okay";
+};
+
+&mmc0 {
+ vmmc-supply = <®_dcdc1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&mmc1 {
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ vmmc-supply = <®_dldo1>;
+ vqmmc-supply = <®_dldo1>;
+ non-removable;
+ wakeup-source;
+ status = "okay";
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 WL_WAKE_UP */
+ interrupt-names = "host-wake";
+ };
+};
+
+&mmc2 {
+ pinctrl-0 = <&mmc2_8bit_emmc_pins>;
+ pinctrl-names = "default";
+ vmmc-supply = <®_dcdc1>;
+ vqmmc-supply = <®_dcdc1>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm_pin>;
+ status = "okay";
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp81x: pmic@3a3 {
+ compatible = "x-powers,axp813";
+ reg = <0x3a3>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ swin-supply = <®_dcdc1>;
+ x-powers,drive-vbus-en;
+ };
+
+ ac100: codec@e89 {
+ compatible = "x-powers,ac100";
+ reg = <0xe89>;
+
+ ac100_codec: codec {
+ compatible = "x-powers,ac100-codec";
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 12 IRQ_TYPE_LEVEL_LOW>; /* PL12 */
+ #clock-cells = <0>;
+ clock-output-names = "4M_adda";
+ };
+
+ ac100_rtc: rtc {
+ compatible = "x-powers,ac100-rtc";
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&ac100_codec>;
+ #clock-cells = <1>;
+ clock-output-names = "cko1_rtc",
+ "cko2_rtc",
+ "cko3_rtc";
+ };
+ };
+
+};
+
+#include "axp81x.dtsi"
+
+&battery_power_supply {
+ status = "okay";
+};
+
+®_aldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-1.8";
+};
+
+®_aldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-name = "vdd-drampll";
+};
+
+®_aldo3 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ regulator-name = "avcc";
+};
+
+®_dcdc1 {
+ regulator-min-microvolt = <3100000>;
+ regulator-max-microvolt = <3100000>;
+ regulator-always-on;
+ regulator-name = "vcc-io";
+};
+
+®_dcdc2 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ regulator-name = "vdd-cpu-A";
+};
+
+®_dcdc3 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ regulator-name = "vdd-cpu-B";
+};
+
+®_dcdc4 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc5 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-name = "vcc-dram";
+};
+
+®_dcdc6 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-always-on;
+ regulator-name = "vdd-sys";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3100000>;
+ regulator-max-microvolt = <3100000>;
+ regulator-name = "vcc-wifi-io";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <4200000>;
+ regulator-name = "vcc-mipi";
+};
+
+®_dldo3 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "vdd-csi";
+};
+
+®_dldo4 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "avdd-csi";
+};
+
+®_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
+®_eldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "dvdd-csi-r";
+};
+
+®_eldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-dsi";
+};
+
+®_eldo3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "dvdd-csi-f";
+};
+
-&ohci0 {
+®_fldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-hsic";
+};
+
+®_fldo2 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ regulator-name = "vdd-cpus";
+};
+
+®_ldo_io0 {
+ regulator-min-microvolt = <3100000>;
+ regulator-max-microvolt = <3100000>;
+ regulator-name = "vcc-ctp";
status = "okay";
};
+®_ldo_io1 {
+ regulator-min-microvolt = <3100000>;
+ regulator-max-microvolt = <3100000>;
+ regulator-name = "vcc-vb";
+ status = "okay";
+};
+
+®_sw {
+ regulator-min-microvolt = <3100000>;
+ regulator-max-microvolt = <3100000>;
+ regulator-name = "vcc-lcd";
+};
+
+&tcon0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_lvds_pins>;
+};
+
+&tcon0_out {
+ tcon0_out_lcd: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&panel_input>;
+ };
+};
+
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_b>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
+/* There's the BT part of the AP6210 connected to that UART */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+ status = "okay";
+};
+
&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
+ usb0_vbus-supply = <®_drivevbus>;
+ usb1_vbus_supply = <®_vmain>;
+ usb2_vbus_supply = <®_vmain>;
status = "okay";
};
diff --git a/arch/arm/dts/sun8i-a83t.dtsi b/arch/arm/dts/sun8i-a83t.dtsi
index 2953e0f..2be23d6 100644
--- a/arch/arm/dts/sun8i-a83t.dtsi
+++ b/arch/arm/dts/sun8i-a83t.dtsi
@@ -40,67 +40,99 @@
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
-
*/
-#include "skeleton.dtsi"
-
#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/clock/sun8i-a83t-ccu.h>
+#include <dt-bindings/clock/sun8i-de2.h>
+#include <dt-bindings/clock/sun8i-r-ccu.h>
+#include <dt-bindings/reset/sun8i-a83t-ccu.h>
+#include <dt-bindings/reset/sun8i-de2.h>
+#include <dt-bindings/reset/sun8i-r-ccu.h>
/ {
interrupt-parent = <&gic>;
+ #address-cells = <1>;
+ #size-cells = <1>;
cpus {
#address-cells = <1>;
#size-cells = <0>;
- cpu@0 {
+ cpu0: cpu@0 {
+ clocks = <&ccu CLK_C0CPUX>;
+ clock-names = "cpu";
compatible = "arm,cortex-a7";
device_type = "cpu";
+ operating-points-v2 = <&cpu0_opp_table>;
+ cci-control-port = <&cci_control0>;
+ enable-method = "allwinner,sun8i-a83t-smp";
reg = <0>;
};
cpu@1 {
compatible = "arm,cortex-a7";
device_type = "cpu";
+ operating-points-v2 = <&cpu0_opp_table>;
+ cci-control-port = <&cci_control0>;
+ enable-method = "allwinner,sun8i-a83t-smp";
reg = <1>;
};
cpu@2 {
compatible = "arm,cortex-a7";
device_type = "cpu";
+ operating-points-v2 = <&cpu0_opp_table>;
+ cci-control-port = <&cci_control0>;
+ enable-method = "allwinner,sun8i-a83t-smp";
reg = <2>;
};
cpu@3 {
compatible = "arm,cortex-a7";
device_type = "cpu";
+ operating-points-v2 = <&cpu0_opp_table>;
+ cci-control-port = <&cci_control0>;
+ enable-method = "allwinner,sun8i-a83t-smp";
reg = <3>;
};
- cpu@100 {
+ cpu100: cpu@100 {
+ clocks = <&ccu CLK_C1CPUX>;
+ clock-names = "cpu";
compatible = "arm,cortex-a7";
device_type = "cpu";
+ operating-points-v2 = <&cpu1_opp_table>;
+ cci-control-port = <&cci_control1>;
+ enable-method = "allwinner,sun8i-a83t-smp";
reg = <0x100>;
};
cpu@101 {
compatible = "arm,cortex-a7";
device_type = "cpu";
+ operating-points-v2 = <&cpu1_opp_table>;
+ cci-control-port = <&cci_control1>;
+ enable-method = "allwinner,sun8i-a83t-smp";
reg = <0x101>;
};
cpu@102 {
compatible = "arm,cortex-a7";
device_type = "cpu";
+ operating-points-v2 = <&cpu1_opp_table>;
+ cci-control-port = <&cci_control1>;
+ enable-method = "allwinner,sun8i-a83t-smp";
reg = <0x102>;
};
cpu@103 {
compatible = "arm,cortex-a7";
device_type = "cpu";
+ operating-points-v2 = <&cpu1_opp_table>;
+ cci-control-port = <&cci_control1>;
+ enable-method = "allwinner,sun8i-a83t-smp";
reg = <0x103>;
};
};
@@ -123,6 +155,7 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
+ clock-accuracy = <50000>;
clock-output-names = "osc24M";
};
@@ -148,48 +181,575 @@
};
};
+ de: display-engine {
+ compatible = "allwinner,sun8i-a83t-display-engine";
+ allwinner,pipelines = <&mixer0>, <&mixer1>;
+ status = "disabled";
+ };
+
+ memory {
+ reg = <0x40000000 0x80000000>;
+ device_type = "memory";
+ };
+
+ cpu0_opp_table: opp_table0 {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-480000000 {
+ opp-hz = /bits/ 64 <480000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-600000000 {
+ opp-hz = /bits/ 64 <600000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-720000000 {
+ opp-hz = /bits/ 64 <720000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-864000000 {
+ opp-hz = /bits/ 64 <864000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-912000000 {
+ opp-hz = /bits/ 64 <912000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-1008000000 {
+ opp-hz = /bits/ 64 <1008000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-1128000000 {
+ opp-hz = /bits/ 64 <1128000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-1200000000 {
+ opp-hz = /bits/ 64 <1200000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+ };
+
+ cpu1_opp_table: opp_table1 {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-480000000 {
+ opp-hz = /bits/ 64 <480000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-600000000 {
+ opp-hz = /bits/ 64 <600000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-720000000 {
+ opp-hz = /bits/ 64 <720000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-864000000 {
+ opp-hz = /bits/ 64 <864000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-912000000 {
+ opp-hz = /bits/ 64 <912000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-1008000000 {
+ opp-hz = /bits/ 64 <1008000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-1128000000 {
+ opp-hz = /bits/ 64 <1128000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp-1200000000 {
+ opp-hz = /bits/ 64 <1200000000>;
+ opp-microvolt = <840000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+ };
+
soc {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
+ display_clocks: clock@1000000 {
+ compatible = "allwinner,sun8i-a83t-de2-clk";
+ reg = <0x01000000 0x100000>;
+ clocks = <&ccu CLK_PLL_DE>,
+ <&ccu CLK_BUS_DE>;
+ clock-names = "mod",
+ "bus";
+ resets = <&ccu RST_BUS_DE>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ mixer0: mixer@1100000 {
+ compatible = "allwinner,sun8i-a83t-de2-mixer-0";
+ reg = <0x01100000 0x100000>;
+ clocks = <&display_clocks CLK_BUS_MIXER0>,
+ <&display_clocks CLK_MIXER0>;
+ clock-names = "bus",
+ "mod";
+ resets = <&display_clocks RST_MIXER0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mixer0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ mixer0_out_tcon0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon0_in_mixer0>;
+ };
+ };
+ };
+ };
+
+ mixer1: mixer@1200000 {
+ compatible = "allwinner,sun8i-a83t-de2-mixer-1";
+ reg = <0x01200000 0x100000>;
+ clocks = <&display_clocks CLK_BUS_MIXER1>,
+ <&display_clocks CLK_MIXER1>;
+ clock-names = "bus",
+ "mod";
+ resets = <&display_clocks RST_WB>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mixer1_out: port@1 {
+ reg = <1>;
+
+ mixer1_out_tcon1: endpoint {
+ remote-endpoint = <&tcon1_in_mixer1>;
+ };
+ };
+ };
+ };
+
+ cpucfg@1700000 {
+ compatible = "allwinner,sun8i-a83t-cpucfg";
+ reg = <0x01700000 0x400>;
+ };
+
+ cci@1790000 {
+ compatible = "arm,cci-400";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x01790000 0x10000>;
+ ranges = <0x0 0x01790000 0x10000>;
+
+ cci_control0: slave-if@4000 {
+ compatible = "arm,cci-400-ctrl-if";
+ interface-type = "ace";
+ reg = <0x4000 0x1000>;
+ };
+
+ cci_control1: slave-if@5000 {
+ compatible = "arm,cci-400-ctrl-if";
+ interface-type = "ace";
+ reg = <0x5000 0x1000>;
+ };
+
+ pmu@9000 {
+ compatible = "arm,cci-400-pmu,r1";
+ reg = <0x9000 0x5000>;
+ interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ syscon: syscon@1c00000 {
+ compatible = "allwinner,sun8i-a83t-system-controller",
+ "syscon";
+ reg = <0x01c00000 0x1000>;
+ };
+
+ dma: dma-controller@1c02000 {
+ compatible = "allwinner,sun8i-a83t-dma";
+ reg = <0x01c02000 0x1000>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_DMA>;
+ resets = <&ccu RST_BUS_DMA>;
+ #dma-cells = <1>;
+ };
+
+ tcon0: lcd-controller@1c0c000 {
+ compatible = "allwinner,sun8i-a83t-tcon-lcd";
+ reg = <0x01c0c000 0x1000>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_TCON0>, <&ccu CLK_TCON0>;
+ clock-names = "ahb", "tcon-ch0";
+ clock-output-names = "tcon-pixel-clock";
+ resets = <&ccu RST_BUS_TCON0>, <&ccu RST_BUS_LVDS>;
+ reset-names = "lcd", "lvds";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon0_in: port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ tcon0_in_mixer0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&mixer0_out_tcon0>;
+ };
+ };
+
+ tcon0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+ };
+ };
+
+ tcon1: lcd-controller@1c0d000 {
+ compatible = "allwinner,sun8i-a83t-tcon-tv";
+ reg = <0x01c0d000 0x1000>;
+ interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_TCON1>, <&ccu CLK_TCON1>;
+ clock-names = "ahb", "tcon-ch1";
+ resets = <&ccu RST_BUS_TCON1>;
+ reset-names = "lcd";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon1_in: port@0 {
+ reg = <0>;
+
+ tcon1_in_mixer1: endpoint {
+ remote-endpoint = <&mixer1_out_tcon1>;
+ };
+ };
+
+ tcon1_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ tcon1_out_hdmi: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&hdmi_in_tcon1>;
+ };
+ };
+ };
+ };
+
+ mmc0: mmc@1c0f000 {
+ compatible = "allwinner,sun8i-a83t-mmc",
+ "allwinner,sun7i-a20-mmc";
+ reg = <0x01c0f000 0x1000>;
+ clocks = <&ccu CLK_BUS_MMC0>,
+ <&ccu CLK_MMC0>,
+ <&ccu CLK_MMC0_OUTPUT>,
+ <&ccu CLK_MMC0_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ resets = <&ccu RST_BUS_MMC0>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc@1c10000 {
+ compatible = "allwinner,sun8i-a83t-mmc",
+ "allwinner,sun7i-a20-mmc";
+ reg = <0x01c10000 0x1000>;
+ clocks = <&ccu CLK_BUS_MMC1>,
+ <&ccu CLK_MMC1>,
+ <&ccu CLK_MMC1_OUTPUT>,
+ <&ccu CLK_MMC1_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ resets = <&ccu RST_BUS_MMC1>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc@1c11000 {
+ compatible = "allwinner,sun8i-a83t-emmc";
+ reg = <0x01c11000 0x1000>;
+ clocks = <&ccu CLK_BUS_MMC2>,
+ <&ccu CLK_MMC2>,
+ <&ccu CLK_MMC2_OUTPUT>,
+ <&ccu CLK_MMC2_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ resets = <&ccu RST_BUS_MMC2>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ sid: eeprom@1c14000 {
+ compatible = "allwinner,sun8i-a83t-sid";
+ reg = <0x1c14000 0x400>;
+ };
+
+ usb_otg: usb@1c19000 {
+ compatible = "allwinner,sun8i-a83t-musb",
+ "allwinner,sun8i-a33-musb";
+ reg = <0x01c19000 0x0400>;
+ clocks = <&ccu CLK_BUS_OTG>;
+ resets = <&ccu RST_BUS_OTG>;
+ interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "mc";
+ phys = <&usbphy 0>;
+ phy-names = "usb";
+ extcon = <&usbphy 0>;
+ status = "disabled";
+ };
+
+ usbphy: phy@1c19400 {
+ compatible = "allwinner,sun8i-a83t-usb-phy";
+ reg = <0x01c19400 0x10>,
+ <0x01c1a800 0x14>,
+ <0x01c1b800 0x14>;
+ reg-names = "phy_ctrl",
+ "pmu1",
+ "pmu2";
+ clocks = <&ccu CLK_USB_PHY0>,
+ <&ccu CLK_USB_PHY1>,
+ <&ccu CLK_USB_HSIC>,
+ <&ccu CLK_USB_HSIC_12M>;
+ clock-names = "usb0_phy",
+ "usb1_phy",
+ "usb2_phy",
+ "usb2_hsic_12M";
+ resets = <&ccu RST_USB_PHY0>,
+ <&ccu RST_USB_PHY1>,
+ <&ccu RST_USB_HSIC>;
+ reset-names = "usb0_reset",
+ "usb1_reset",
+ "usb2_reset";
+ status = "disabled";
+ #phy-cells = <1>;
+ };
+
+ ehci0: usb@1c1a000 {
+ compatible = "allwinner,sun8i-a83t-ehci",
+ "generic-ehci";
+ reg = <0x01c1a000 0x100>;
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI0>;
+ resets = <&ccu RST_BUS_EHCI0>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci0: usb@1c1a400 {
+ compatible = "allwinner,sun8i-a83t-ohci",
+ "generic-ohci";
+ reg = <0x01c1a400 0x100>;
+ interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI0>, <&ccu CLK_USB_OHCI0>;
+ resets = <&ccu RST_BUS_OHCI0>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ehci1: usb@1c1b000 {
+ compatible = "allwinner,sun8i-a83t-ehci",
+ "generic-ehci";
+ reg = <0x01c1b000 0x100>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI1>;
+ resets = <&ccu RST_BUS_EHCI1>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ccu: clock@1c20000 {
+ compatible = "allwinner,sun8i-a83t-ccu";
+ reg = <0x01c20000 0x400>;
+ clocks = <&osc24M>, <&osc16Md512>;
+ clock-names = "hosc", "losc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
- pio: pinctrl@01c20800 {
+ pio: pinctrl@1c20800 {
compatible = "allwinner,sun8i-a83t-pinctrl";
interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x01c20800 0x400>;
- clocks = <&osc24M>;
+ clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc16Md512>;
+ clock-names = "apb", "hosc", "losc";
gpio-controller;
interrupt-controller;
#interrupt-cells = <3>;
#gpio-cells = <3>;
+ emac_rgmii_pins: emac-rgmii-pins {
+ pins = "PD2", "PD3", "PD4", "PD5", "PD6", "PD7",
+ "PD11", "PD12", "PD13", "PD14", "PD18",
+ "PD19", "PD21", "PD22", "PD23";
+ function = "gmac";
+ /*
+ * data lines in RGMII mode use DDR mode
+ * and need a higher signal drive strength
+ */
+ drive-strength = <40>;
+ };
+
+ hdmi_pins: hdmi-pins {
+ pins = "PH6", "PH7", "PH8";
+ function = "hdmi";
+ };
+
+ i2c0_pins: i2c0-pins {
+ pins = "PH0", "PH1";
+ function = "i2c0";
+ };
+
+ i2c1_pins: i2c1-pins {
+ pins = "PH2", "PH3";
+ function = "i2c1";
+ };
+
+ i2c2_ph_pins: i2c2-ph-pins {
+ pins = "PH4", "PH5";
+ function = "i2c2";
+ };
+
+ i2s1_pins: i2s1-pins {
+ /* I2S1 does not have external MCLK pin */
+ pins = "PG10", "PG11", "PG12", "PG13";
+ function = "i2s1";
+ };
+
+ lcd_lvds_pins: lcd-lvds-pins {
+ pins = "PD18", "PD19", "PD20", "PD21", "PD22",
+ "PD23", "PD24", "PD25", "PD26", "PD27";
+ function = "lvds0";
+ };
+
+ mmc0_pins: mmc0-pins {
+ pins = "PF0", "PF1", "PF2",
+ "PF3", "PF4", "PF5";
+ function = "mmc0";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc1_pins: mmc1-pins {
+ pins = "PG0", "PG1", "PG2",
+ "PG3", "PG4", "PG5";
+ function = "mmc1";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc2_8bit_emmc_pins: mmc2-8bit-emmc-pins {
+ pins = "PC5", "PC6", "PC8", "PC9",
+ "PC10", "PC11", "PC12", "PC13",
+ "PC14", "PC15", "PC16";
+ function = "mmc2";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ pwm_pin: pwm-pin {
+ pins = "PD28";
+ function = "pwm";
+ };
+
+ spdif_tx_pin: spdif-tx-pin {
+ pins = "PE18";
+ function = "spdif";
+ };
+
+ uart0_pb_pins: uart0-pb-pins {
+ pins = "PB9", "PB10";
+ function = "uart0";
+ };
+
- mmc0_pins_a: mmc0@0 {
- allwinner,pins = "PF0", "PF1", "PF2",
- "PF3", "PF4", "PF5";
- allwinner,function = "mmc0";
- allwinner,drive = <SUN4I_PINCTRL_30_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ uart0_pf_pins: uart0-pf-pins {
+ pins = "PF2", "PF4";
+ function = "uart0";
};
- uart0_pins_a: uart0@0 {
- allwinner,pins = "PF2", "PF4";
- allwinner,function = "uart0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ uart1_pins: uart1-pins {
+ pins = "PG6", "PG7";
+ function = "uart1";
};
- uart0_pins_b: uart0@1 {
- allwinner,pins = "PB9", "PB10";
- allwinner,function = "uart0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ uart1_rts_cts_pins: uart1-rts-cts-pins {
+ pins = "PG8", "PG9";
+ function = "uart1";
};
};
- timer@01c20c00 {
+ timer@1c20c00 {
compatible = "allwinner,sun4i-a10-timer";
reg = <0x01c20c00 0xa0>;
interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
@@ -197,27 +757,166 @@
clocks = <&osc24M>;
};
- watchdog@01c20ca0 {
+ watchdog@1c20ca0 {
compatible = "allwinner,sun6i-a31-wdt";
reg = <0x01c20ca0 0x20>;
interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&osc24M>;
};
+ spdif: spdif@1c21000 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun8i-a83t-spdif",
+ "allwinner,sun8i-h3-spdif";
+ reg = <0x01c21000 0x400>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
+ resets = <&ccu RST_BUS_SPDIF>;
+ clock-names = "apb", "spdif";
+ dmas = <&dma 2>;
+ dma-names = "tx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spdif_tx_pin>;
+ status = "disabled";
+ };
+
- uart0: serial@01c28000 {
+ i2s0: i2s@1c22000 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun8i-a83t-i2s";
+ reg = <0x01c22000 0x400>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2S0>, <&ccu CLK_I2S0>;
+ clock-names = "apb", "mod";
+ dmas = <&dma 3>, <&dma 3>;
+ resets = <&ccu RST_BUS_I2S0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ i2s1: i2s@1c22400 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun8i-a83t-i2s";
+ reg = <0x01c22400 0x400>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2S1>, <&ccu CLK_I2S1>;
+ clock-names = "apb", "mod";
+ dmas = <&dma 4>, <&dma 4>;
+ resets = <&ccu RST_BUS_I2S1>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s1_pins>;
+ status = "disabled";
+ };
+
+ i2s2: i2s@1c22800 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun8i-a83t-i2s";
+ reg = <0x01c22800 0x400>;
+ interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2S2>, <&ccu CLK_I2S2>;
+ clock-names = "apb", "mod";
+ dmas = <&dma 27>;
+ resets = <&ccu RST_BUS_I2S2>;
+ dma-names = "tx";
+ status = "disabled";
+ };
+
+ pwm: pwm@1c21400 {
+ compatible = "allwinner,sun8i-a83t-pwm",
+ "allwinner,sun8i-h3-pwm";
+ reg = <0x01c21400 0x400>;
+ clocks = <&osc24M>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ uart0: serial@1c28000 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28000 0x400>;
interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&osc24M>;
+ clocks = <&ccu CLK_BUS_UART0>;
+ resets = <&ccu RST_BUS_UART0>;
status = "disabled";
};
- gic: interrupt-controller@01c81000 {
+ uart1: serial@1c28400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28400 0x400>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART1>;
+ resets = <&ccu RST_BUS_UART1>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@1c2ac00 {
+ compatible = "allwinner,sun8i-a83t-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2ac00 0x400>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C0>;
+ resets = <&ccu RST_BUS_I2C0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c@1c2b000 {
+ compatible = "allwinner,sun8i-a83t-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C1>;
+ resets = <&ccu RST_BUS_I2C1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c@1c2b400 {
+ compatible = "allwinner,sun8i-a83t-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b400 0x400>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C2>;
+ resets = <&ccu RST_BUS_I2C2>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ emac: ethernet@1c30000 {
+ compatible = "allwinner,sun8i-a83t-emac";
+ syscon = <&syscon>;
+ reg = <0x01c30000 0x104>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ resets = <&ccu 13>;
+ reset-names = "stmmaceth";
+ clocks = <&ccu 27>;
+ clock-names = "stmmaceth";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+
+ mdio: mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ gic: interrupt-controller@1c81000 {
compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
reg = <0x01c81000 0x1000>,
- <0x01c82000 0x1000>,
+ <0x01c82000 0x2000>,
<0x01c84000 0x2000>,
<0x01c86000 0x2000>;
interrupt-controller;
@@ -225,59 +924,107 @@
interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
};
- usb_otg: usb@01c19000 {
- compatible = "allwinner,sun8i-a33-musb";
- reg = <0x01c19000 0x400>;
- interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "mc";
- phys = <&usbphy 0>;
- phy-names = "usb";
+ hdmi: hdmi@1ee0000 {
+ compatible = "allwinner,sun8i-a83t-dw-hdmi";
+ reg = <0x01ee0000 0x10000>;
+ reg-io-width = <1>;
+ interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_SLOW>,
+ <&ccu CLK_HDMI>;
+ clock-names = "iahb", "isfr", "tmds";
+ resets = <&ccu RST_BUS_HDMI1>;
+ reset-names = "ctrl";
+ phys = <&hdmi_phy>;
+ phy-names = "hdmi-phy";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_pins>;
status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hdmi_in: port@0 {
+ reg = <0>;
+
+ hdmi_in_tcon1: endpoint {
+ remote-endpoint = <&tcon1_out_hdmi>;
+ };
+ };
+
+ hdmi_out: port@1 {
+ reg = <1>;
+ };
+ };
};
- usbphy: phy@1c19400 {
- compatible = "allwinner,sun8i-a83t-usb-phy";
- reg = <0x01c19400 0x10>,
- <0x01c1a800 0x14>,
- <0x01c1b800 0x14>;
- reg-names = "phy_ctrl",
- "pmu1",
- "pmu2";
- status = "disabled";
- #phy-cells = <1>;
+ hdmi_phy: hdmi-phy@1ef0000 {
+ compatible = "allwinner,sun8i-a83t-hdmi-phy";
+ reg = <0x01ef0000 0x10000>;
+ clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_SLOW>;
+ clock-names = "bus", "mod";
+ resets = <&ccu RST_BUS_HDMI0>;
+ reset-names = "phy";
+ #phy-cells = <0>;
};
- ehci0: usb@01c1a000 {
- compatible = "allwinner,sun8i-a83t-ehci", "generic-ehci";
- reg = <0x01c1a000 0x100>;
- interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
+ r_intc: interrupt-controller@1f00c00 {
+ compatible = "allwinner,sun8i-a83t-r-intc",
+ "allwinner,sun6i-a31-r-intc";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x01f00c00 0x400>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
};
- ohci0: usb@01c1a400 {
- compatible = "allwinner,sun8i-a83t-ohci", "generic-ohci";
- reg = <0x01c1a400 0x100>;
- interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
+ r_ccu: clock@1f01400 {
+ compatible = "allwinner,sun8i-a83t-r-ccu";
+ reg = <0x01f01400 0x400>;
+ clocks = <&osc24M>, <&osc16Md512>, <&osc16M>,
+ <&ccu 6>;
+ clock-names = "hosc", "losc", "iosc", "pll-periph";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
};
- ehci1: usb@01c1b000 {
- compatible = "allwinner,sun8i-a83t-ehci", "generic-ehci";
- reg = <0x01c1b000 0x100>;
- interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
+ r_cpucfg@1f01c00 {
+ compatible = "allwinner,sun8i-a83t-r-cpucfg";
+ reg = <0x1f01c00 0x400>;
};
- r_pio: pinctrl@01f02c00 {
+ r_pio: pinctrl@1f02c00 {
compatible = "allwinner,sun8i-a83t-r-pinctrl";
reg = <0x01f02c00 0x400>;
interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu CLK_APB0_PIO>, <&osc24M>,
+ <&osc16Md512>;
+ clock-names = "apb", "hosc", "losc";
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+
+ r_rsb_pins: r-rsb-pins {
+ pins = "PL0", "PL1";
+ function = "s_rsb";
+ drive-strength = <20>;
+ bias-pull-up;
+ };
+ };
+
+ r_rsb: rsb@1f03400 {
+ compatible = "allwinner,sun8i-a83t-rsb",
+ "allwinner,sun8i-a23-rsb";
+ reg = <0x01f03400 0x400>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu CLK_APB0_RSB>;
+ clock-frequency = <3000000>;
+ resets = <&r_ccu RST_APB0_RSB>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_rsb_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
};
};
};
diff --git a/include/dt-bindings/clock/sun8i-a83t-ccu.h b/include/dt-bindings/clock/sun8i-a83t-ccu.h
new file mode 100644
index 0000000..78af508
--- /dev/null
+++ b/include/dt-bindings/clock/sun8i-a83t-ccu.h
@@ -0,0 +1,140 @@
+/*
+ * Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_CLOCK_SUN8I_A83T_CCU_H_
+#define _DT_BINDINGS_CLOCK_SUN8I_A83T_CCU_H_
+
+#define CLK_PLL_PERIPH 6
+
+#define CLK_PLL_DE 9
+
+#define CLK_C0CPUX 11
+#define CLK_C1CPUX 12
+
+#define CLK_BUS_MIPI_DSI 19
+#define CLK_BUS_SS 20
+#define CLK_BUS_DMA 21
+#define CLK_BUS_MMC0 22
+#define CLK_BUS_MMC1 23
+#define CLK_BUS_MMC2 24
+#define CLK_BUS_NAND 25
+#define CLK_BUS_DRAM 26
+#define CLK_BUS_EMAC 27
+#define CLK_BUS_HSTIMER 28
+#define CLK_BUS_SPI0 29
+#define CLK_BUS_SPI1 30
+#define CLK_BUS_OTG 31
+#define CLK_BUS_EHCI0 32
+#define CLK_BUS_EHCI1 33
+#define CLK_BUS_OHCI0 34
+
+#define CLK_BUS_VE 35
+#define CLK_BUS_TCON0 36
+#define CLK_BUS_TCON1 37
+#define CLK_BUS_CSI 38
+#define CLK_BUS_HDMI 39
+#define CLK_BUS_DE 40
+#define CLK_BUS_GPU 41
+#define CLK_BUS_MSGBOX 42
+#define CLK_BUS_SPINLOCK 43
+
+#define CLK_BUS_SPDIF 44
+#define CLK_BUS_PIO 45
+#define CLK_BUS_I2S0 46
+#define CLK_BUS_I2S1 47
+#define CLK_BUS_I2S2 48
+#define CLK_BUS_TDM 49
+
+#define CLK_BUS_I2C0 50
+#define CLK_BUS_I2C1 51
+#define CLK_BUS_I2C2 52
+#define CLK_BUS_UART0 53
+#define CLK_BUS_UART1 54
+#define CLK_BUS_UART2 55
+#define CLK_BUS_UART3 56
+#define CLK_BUS_UART4 57
+
+#define CLK_NAND 59
+#define CLK_MMC0 60
+#define CLK_MMC0_SAMPLE 61
+#define CLK_MMC0_OUTPUT 62
+#define CLK_MMC1 63
+#define CLK_MMC1_SAMPLE 64
+#define CLK_MMC1_OUTPUT 65
+#define CLK_MMC2 66
+#define CLK_MMC2_SAMPLE 67
+#define CLK_MMC2_OUTPUT 68
+#define CLK_SS 69
+#define CLK_SPI0 70
+#define CLK_SPI1 71
+#define CLK_I2S0 72
+#define CLK_I2S1 73
+#define CLK_I2S2 74
+#define CLK_TDM 75
+#define CLK_SPDIF 76
+#define CLK_USB_PHY0 77
+#define CLK_USB_PHY1 78
+#define CLK_USB_HSIC 79
+#define CLK_USB_HSIC_12M 80
+#define CLK_USB_OHCI0 81
+
+#define CLK_DRAM_VE 83
+#define CLK_DRAM_CSI 84
+
+#define CLK_TCON0 85
+#define CLK_TCON1 86
+#define CLK_CSI_MISC 87
+#define CLK_MIPI_CSI 88
+#define CLK_CSI_MCLK 89
+#define CLK_CSI_SCLK 90
+#define CLK_VE 91
+#define CLK_AVS 92
+#define CLK_HDMI 93
+#define CLK_HDMI_SLOW 94
+
+#define CLK_MIPI_DSI0 96
+#define CLK_MIPI_DSI1 97
+#define CLK_GPU_CORE 98
+#define CLK_GPU_MEMORY 99
+#define CLK_GPU_HYD 100
+
+#endif /* _DT_BINDINGS_CLOCK_SUN8I_A83T_CCU_H_ */
diff --git a/include/dt-bindings/reset/sun8i-a83t-ccu.h b/include/dt-bindings/reset/sun8i-a83t-ccu.h
new file mode 100644
index 0000000..784f6e1
--- /dev/null
+++ b/include/dt-bindings/reset/sun8i-a83t-ccu.h
@@ -0,0 +1,98 @@
+/*
+ * Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_RESET_SUN8I_A83T_CCU_H_
+#define _DT_BINDINGS_RESET_SUN8I_A83T_CCU_H_
+
+#define RST_USB_PHY0 0
+#define RST_USB_PHY1 1
+#define RST_USB_HSIC 2
+
+#define RST_DRAM 3
+#define RST_MBUS 4
+
+#define RST_BUS_MIPI_DSI 5
+#define RST_BUS_SS 6
+#define RST_BUS_DMA 7
+#define RST_BUS_MMC0 8
+#define RST_BUS_MMC1 9
+#define RST_BUS_MMC2 10
+#define RST_BUS_NAND 11
+#define RST_BUS_DRAM 12
+#define RST_BUS_EMAC 13
+#define RST_BUS_HSTIMER 14
+#define RST_BUS_SPI0 15
+#define RST_BUS_SPI1 16
+#define RST_BUS_OTG 17
+#define RST_BUS_EHCI0 18
+#define RST_BUS_EHCI1 19
+#define RST_BUS_OHCI0 20
+
+#define RST_BUS_VE 21
+#define RST_BUS_TCON0 22
+#define RST_BUS_TCON1 23
+#define RST_BUS_CSI 24
+#define RST_BUS_HDMI0 25
+#define RST_BUS_HDMI1 26
+#define RST_BUS_DE 27
+#define RST_BUS_GPU 28
+#define RST_BUS_MSGBOX 29
+#define RST_BUS_SPINLOCK 30
+
+#define RST_BUS_LVDS 31
+
+#define RST_BUS_SPDIF 32
+#define RST_BUS_I2S0 33
+#define RST_BUS_I2S1 34
+#define RST_BUS_I2S2 35
+#define RST_BUS_TDM 36
+
+#define RST_BUS_I2C0 37
+#define RST_BUS_I2C1 38
+#define RST_BUS_I2C2 39
+#define RST_BUS_UART0 40
+#define RST_BUS_UART1 41
+#define RST_BUS_UART2 42
+#define RST_BUS_UART3 43
+#define RST_BUS_UART4 44
+
+#endif /* _DT_BINDINGS_RESET_SUN8I_A83T_CCU_H_ */