brppt1: Remove unused board variants

The SPI and NAND board variants never went into production.
Drop those board variants.

Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 7330121..5bff2e6 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -388,8 +388,6 @@
 	am335x-boneblack-wireless.dtb \
 	am335x-boneblue.dtb \
 	am335x-brppt1-mmc.dtb \
-	am335x-brppt1-nand.dtb \
-	am335x-brppt1-spi.dtb \
 	am335x-brxre1.dtb \
 	am335x-brsmarc1.dtb \
 	am335x-draco.dtb \
diff --git a/arch/arm/dts/am335x-brppt1-nand.dts b/arch/arm/dts/am335x-brppt1-nand.dts
deleted file mode 100644
index 67c6097..0000000
--- a/arch/arm/dts/am335x-brppt1-nand.dts
+++ /dev/null
@@ -1,374 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2018 B&R Industrial Automation GmbH
- * http://www.br-automation.com
- *
- */
-/dts-v1/;
-
-#include "am33xx.dtsi"
-
-/ {
-	model = "BRPPT1 (NAND) Panel";
-	compatible = "ti,am33xx";
-
-	fset: factory-settings {
-		bl-version	= "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890";
-		version		= <0x0100>;
-		order-no	= "6PPT30 (NAND)";
-		hw-revision	= "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890";
-		serial-no	= "0";
-		device-id	= <0x0>;
-		parent-id	= <0x0>;
-		hw-variant	= <0x1>;
-	};
-
-	aliases {
-		ds1bkl0 = &pwmbacklight;
-		ds1bkl1 = &tps_bl;
-		ds1timing = &timing0;
-		ds1ctrl = &lcdc;
-		gpmc = &gpmc;
-		mmc = &mmc2;
-		fset = &fset;
-	};
-
-	chosen {
-		bootargs = "console=ttyO0,115200 earlyprintk";
-		stdout-path = &uart0;
-	};
-
-	memory {
-		device_type = "memory";
-		reg = <0x80000000 0x10000000>; /* 256 MB */
-	};
-
-	panel {
-		status = "disabled";
-
-		compatible = "ti,tilcdc,panel";
-		enable-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
-
-		backlight = <&pwmbacklight>;
-		bkl-pwm = <&pwmbacklight>;
-		bkl-tps = <&tps_bl>;
-
-		panel-info {
-			ac-bias		= <255>;
-			ac-bias-intrpt	= <0>;
-			dma-burst-sz	= <16>;
-			bpp		= <32>;
-			fdd		= <0x80>;
-			sync-edge	= <0>;
-			sync-ctrl	= <1>;
-			raster-order	= <0>;
-			fifo-th		= <0>;
-		};
-
-		display-timings {
-			native-mode = <&timing0>;
-			timing0: lcd {
-				clock-frequency	= <32000000>;
-				hactive		= <800>;
-				vactive		= <480>;
-				hfront-porch	= <2>;
-				hback-porch	= <192>;
-				hsync-len	= <1>;
-				vfront-porch	= <20>;
-				vback-porch	= <2>;
-				vsync-len	= <1>;
-				hsync-active	= <1>;
-				vsync-active	= <1>;
-				pupdelay	= <10>;
-				pondelay	= <10>;
-			};
-		};
-	};
-
-	vmmcsd_fixed: fixedregulator@0 {
-		compatible = "regulator-fixed";
-		regulator-name = "vmmcsd_fixed";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	pwm0: omap-pwm@timer5 {
-		compatible = "ti,omap-dmtimer-pwm";
-		ti,timers = <&timer5>;
-		#pwm-cells = <3>;
-	};
-
-	pwm1: omap-pwm@timer6 {
-		compatible = "ti,omap-dmtimer-pwm";
-		ti,timers = <&timer6>;
-		#pwm-cells = <3>;
-	};
-
-	beeper: pwm-beep {
-		compatible = "pwm-beeper";
-		pwms = <&pwm0 0 0 0>;
-	};
-
-	pwmbacklight: pwm-bkl {
-		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000 0>;
-
-		default-brightness-level = <255>;
-		brightness-levels = <0 16 32 64 128 170 202 234 255>;
-
-		power-supply = <&vmmcsd_fixed>;
-		enable-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
-	};
-};
-
-&uart0 {		/* console uart */
-	u-boot,dm-spl;
-	status = "okay";
-};
-
-&uart1 {
-	status = "okay";
-};
-
-&i2c0 {
-	u-boot,dm-spl;
-	status = "okay";
-	clock-frequency = <400000>;
-
-	tps: tps@24 {		/* PMIC controller */
-		u-boot,dm-spl;
-		reg = <0x24>;
-		compatible = "ti,tps65217";
-
-		tps_bl: backlight {
-			compatible = "ti,tps65217-bl";
-			isel = <1>;	/* 1 - ISET1, 2 ISET2 */
-			fdim = <1000>;	/* TPS65217_BL_FDIM_1kHZ */
-			default-brightness = <50>;
-		};
-	};
-};
-
-&i2c2 {
-	status = "okay";
-	clock-frequency = <100000>;
-};
-
-&edma {
-	status = "okay";
-};
-
-&cppi41dma  {
-	status = "okay";
-};
-
-&usb {
-	status = "okay";
-};
-
-&usb_ctrl_mod {
-	status = "okay";
-};
-
-&usb0_phy {
-	status = "okay";
-};
-
-&usb1_phy {
-	status = "okay";
-};
-
-&usb0 {
-	status = "okay";
-	dr_mode = "host";
-};
-
-&usb1 {
-	status = "okay";
-	dr_mode = "host";
-};
-
-&davinci_mdio {
-	status = "okay";
-
-	phy0: ethernet-phy@0 {
-		reg = <1>;
-	};
-
-	phy1: ethernet-phy@1 {
-		reg = <2>;
-	};
-};
-
-&mac {
-	dual_emac;
-	status = "okay";
-};
-
-&cpsw_emac0 {
-	phy-handle = <&phy0>;
-	dual_emac_res_vlan = <1>;
-	phy-mode = "mii";
-};
-
-&cpsw_emac1 {
-	phy-handle = <&phy1>;
-	dual_emac_res_vlan = <2>;
-	phy-mode = "mii";
-};
-
-&mmc2 {
-	vmmc-supply = <&vmmcsd_fixed>;
-	bus-width = <0x4>;
-	ti,non-removable;
-	ti,needs-special-hs-handling;
-	ti,vcc-aux-disable-is-sleep;
-	status = "disabled";
-};
-
-&l4_per {
-
-	segment@300000 {
-
-		target-module@e000 {
-			u-boot,dm-pre-reloc;
-
-			lcdc: lcdc@0 {
-				u-boot,dm-pre-reloc;
-				status = "disabled";
-			};
-		};
-	};
-};
-
-&elm {
-	status = "okay";
-};
-
-&sham {
-	status = "okay";
-};
-
-&aes {
-	status = "okay";
-};
-
-&gpio0 {
-	u-boot,dm-spl;
-	ti,no-reset-on-init;
-};
-
-&gpio1 {
-	u-boot,dm-spl;
-	ti,no-reset-on-init;
-};
-
-&gpio2 {
-	u-boot,dm-spl;
-	ti,no-reset-on-init;
-};
-
-&gpio3 {
-	u-boot,dm-spl;
-	ti,no-reset-on-init;
-};
-
-&wdt2 {
-	ti,no-reset-on-init;
-	ti,no-idle-on-init;
-};
-
-&tscadc {
-	status = "okay";
-	tsc {
-		ti,wires = <4>;
-		ti,x-plate-resistance = <200>;
-		ti,zx-cutoff-ratio = <40>;
-		ti,min_deviation = <60>;
-		ti,max_deviation = <600>;
-		ti,coordinate-readouts = <5>;
-		ti,wire-config = <0x00 0x11 0x22 0x33>;
-
-		bnr-buttons {
-			Home-Button {};
-		};
-	};
-
-	adc {
-		ti,adc-channels = <5 6 7>;
-	};
-};
-
-&gpmc {
-	u-boot,dm-spl;
-	status = "okay";
-	pinctrl-names = "default";
-	ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
-	nand@0,0 {
-		compatible = "ti,omap2-nand";
-		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
-		interrupt-parent = <&gpmc>;
-		rb-gpios = <&gpmc 1 GPIO_ACTIVE_HIGH>; /* gpmc_wait1 */
-		ti,nand-ecc-opt = "bch8";
-		ti,elm-id = <&elm>;
-		nand-bus-width = <8>;
-		gpmc,device-width = <1>;
-		gpmc,sync-clk-ps = <0>;
-		gpmc,cs-on-ns = <0>;
-		gpmc,cs-rd-off-ns = <44>;
-		gpmc,cs-wr-off-ns = <44>;
-		gpmc,adv-on-ns = <6>;
-		gpmc,adv-rd-off-ns = <34>;
-		gpmc,adv-wr-off-ns = <44>;
-		gpmc,we-on-ns = <0>;
-		gpmc,we-off-ns = <40>;
-		gpmc,oe-on-ns = <0>;
-		gpmc,oe-off-ns = <54>;
-		gpmc,access-ns = <64>;
-		gpmc,rd-cycle-ns = <82>;
-		gpmc,wr-cycle-ns = <82>;
-		gpmc,wait-on-read = "true";
-		gpmc,wait-on-write = "true";
-		gpmc,bus-turnaround-ns = <0>;
-		gpmc,cycle2cycle-delay-ns = <0>;
-		gpmc,clk-activation-ns = <0>;
-		gpmc,wait-monitoring-ns = <0>;
-		gpmc,wr-access-ns = <40>;
-		gpmc,wr-data-mux-bus-ns = <0>;
-		gpmc,wait-pin = <1>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		partition@0 {
-			label = "NAND.MLO";
-			reg = <0x00000000 0x000020000>;
-		};
-		partition@1 {
-			label = "NAND.cfgscr";
-			reg = <0x00020000 0x00020000>;
-		};
-		partition@2 {
-			label = "NAND.dtb";
-			reg = <0x00040000 0x00020000>;
-		};
-		partition@3 {
-			label = "NAND.u-boot-env";
-			reg = <0x00060000 0x00020000>;
-		};
-		partition@4 {
-			label = "NAND.u-boot";
-			reg = <0x00080000 0x00080000>;
-		};
-		partition@5 {
-			label = "NAND.kernel";
-			reg = <0x00100000 0x00400000>;
-		};
-		partition@6 {
-			label = "NAND.rootfs";
-			reg = <0x00500000 0x08000000>;
-		};
-		partition@7 {
-			label = "NAND.user";
-			reg = <0x08500000 0x17b00000>;
-		};
-	};
-};
diff --git a/arch/arm/dts/am335x-brppt1-spi.dts b/arch/arm/dts/am335x-brppt1-spi.dts
deleted file mode 100644
index ce3dce2..0000000
--- a/arch/arm/dts/am335x-brppt1-spi.dts
+++ /dev/null
@@ -1,377 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2018 B&R Industrial Automation GmbH
- * http://www.br-automation.com
- *
- */
-/dts-v1/;
-
-#include "am33xx.dtsi"
-
-/ {
-	model = "BRPPT1 (MMC) Panel";
-	compatible = "ti,am33xx";
-
-	fset: factory-settings {
-		bl-version	= "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890";
-		version		= <0x0100>;
-		order-no	= "6PPT30 (SPI)";
-		hw-revision	= "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890";
-		serial-no	= "0";
-		device-id	= <0x0>;
-		parent-id	= <0x0>;
-		hw-variant	= <0x1>;
-	};
-
-	aliases {
-		ds1bkl0 = &pwmbacklight;
-		ds1bkl1 = &tps_bl;
-		ds1timing = &timing0;
-		ds1ctrl = &lcdc;
-		gpmc = &gpmc;
-		mmc = &mmc2;
-		spi0 = &spi0;
-		fset = &fset;
-	};
-
-	chosen {
-		bootargs = "console=ttyO0,115200 earlyprintk";
-		stdout-path = &uart0;
-	};
-
-	memory {
-		device_type = "memory";
-		reg = <0x80000000 0x10000000>; /* 256 MB */
-	};
-
-	panel {
-		status = "disabled";
-
-		compatible = "ti,tilcdc,panel";
-		enable-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
-
-		backlight = <&pwmbacklight>;
-		bkl-pwm = <&pwmbacklight>;
-		bkl-tps = <&tps_bl>;
-
-		panel-info {
-			ac-bias		= <255>;
-			ac-bias-intrpt	= <0>;
-			dma-burst-sz	= <16>;
-			bpp		= <32>;
-			fdd		= <0x80>;
-			sync-edge	= <0>;
-			sync-ctrl	= <1>;
-			raster-order	= <0>;
-			fifo-th		= <0>;
-		};
-
-		display-timings {
-			native-mode = <&timing0>;
-			timing0: lcd {
-				clock-frequency	= <32000000>;
-				hactive		= <800>;
-				vactive		= <480>;
-				hfront-porch	= <2>;
-				hback-porch	= <192>;
-				hsync-len	= <1>;
-				vfront-porch	= <20>;
-				vback-porch	= <2>;
-				vsync-len	= <1>;
-				hsync-active	= <1>;
-				vsync-active	= <1>;
-				pupdelay	= <10>;
-				pondelay	= <10>;
-			};
-		};
-	};
-
-	vmmcsd_fixed: fixedregulator@0 {
-		compatible = "regulator-fixed";
-		regulator-name = "vmmcsd_fixed";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	pwm0: omap-pwm@timer5 {
-		compatible = "ti,omap-dmtimer-pwm";
-		ti,timers = <&timer5>;
-		#pwm-cells = <3>;
-	};
-
-	pwm1: omap-pwm@timer6 {
-		compatible = "ti,omap-dmtimer-pwm";
-		ti,timers = <&timer6>;
-		#pwm-cells = <3>;
-	};
-
-	beeper: pwm-beep {
-		compatible = "pwm-beeper";
-		pwms = <&pwm0 0 0 0>;
-	};
-
-	pwmbacklight: pwm-bkl {
-		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000 0>;
-
-		default-brightness-level = <255>;
-		brightness-levels = <0 16 32 64 128 170 202 234 255>;
-
-		power-supply = <&vmmcsd_fixed>;
-		enable-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
-	};
-};
-
-&uart0 {		/* console uart */
-	u-boot,dm-spl;
-	status = "okay";
-};
-
-&uart1 {
-	status = "okay";
-};
-
-&i2c0 {
-	u-boot,dm-spl;
-	status = "okay";
-	clock-frequency = <400000>;
-
-	tps: tps@24 {		/* PMIC controller */
-		u-boot,dm-spl;
-		reg = <0x24>;
-		compatible = "ti,tps65217";
-
-		tps_bl: backlight {
-			compatible = "ti,tps65217-bl";
-			isel = <1>;	/* 1 - ISET1, 2 ISET2 */
-			fdim = <1000>;	/* TPS65217_BL_FDIM_1kHZ */
-			default-brightness = <50>;
-		};
-	};
-};
-
-&i2c2 {
-	status = "okay";
-	clock-frequency = <100000>;
-};
-
-&spi0 {
-	u-boot,dm-spl;
-	status = "okay";
-
-	cs-gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>,
-		   <&gpio0 6 GPIO_ACTIVE_HIGH>,
-		   <0>,
-		   <0>;
-
-	spi-max-frequency = <24000000>;
-
-	spi_flash: spiflash@0 {
-		u-boot,dm-spl;
-		u-boot,dm-pre-reloc;
-		compatible = "spidev", "jedec,spi-nor";
-		spi-max-frequency = <24000000>;
-		reg = <0>;
-	};
-};
-
-&edma {
-	status = "okay";
-};
-
-&cppi41dma  {
-	status = "okay";
-};
-
-&usb {
-	status = "okay";
-};
-
-&usb_ctrl_mod {
-	status = "okay";
-};
-
-&usb0_phy {
-	status = "okay";
-};
-
-&usb1_phy {
-	status = "okay";
-};
-
-&usb0 {
-	status = "okay";
-	dr_mode = "host";
-};
-
-&usb1 {
-	status = "okay";
-	dr_mode = "host";
-};
-
-&davinci_mdio {
-	status = "okay";
-
-	phy0: ethernet-phy@0 {
-		reg = <1>;
-	};
-
-	phy1: ethernet-phy@1 {
-		reg = <2>;
-	};
-};
-
-&mac {
-	status = "okay";
-};
-
-&cpsw_emac0 {
-	phy-handle = <&phy0>;
-	dual_emac_res_vlan = <1>;
-	phy-mode = "mii";
-};
-
-&cpsw_emac1 {
-	phy-handle = <&phy1>;
-	dual_emac_res_vlan = <2>;
-	phy-mode = "mii";
-};
-
-&mmc1 {
-	u-boot,dm-spl;
-	vmmc-supply = <&vmmcsd_fixed>;
-	bus-width = <0x4>;
-	ti,non-removable;
-	ti,needs-special-hs-handling;
-	ti,vcc-aux-disable-is-sleep;
-	status = "okay";
-};
-
-&mmc2 {
-	u-boot,dm-spl;
-	vmmc-supply = <&vmmcsd_fixed>;
-	bus-width = <0x8>;
-	ti,non-removable;
-	ti,needs-special-hs-handling;
-	ti,vcc-aux-disable-is-sleep;
-	status = "okay";
-};
-
-&l4_per {
-
-	segment@300000 {
-
-		target-module@e000 {
-			u-boot,dm-pre-reloc;
-
-			lcdc: lcdc@0 {
-				u-boot,dm-pre-reloc;
-				status = "disabled";
-			};
-		};
-	};
-};
-
-&elm {
-	status = "okay";
-};
-
-&sham {
-	status = "okay";
-};
-
-&aes {
-	status = "okay";
-};
-
-&gpio0 {
-	u-boot,dm-spl;
-	ti,no-reset-on-init;
-};
-
-&gpio1 {
-	u-boot,dm-spl;
-	ti,no-reset-on-init;
-};
-
-&gpio2 {
-	u-boot,dm-spl;
-	ti,no-reset-on-init;
-};
-
-&gpio3 {
-	u-boot,dm-spl;
-	ti,no-reset-on-init;
-};
-
-&wdt2 {
-	ti,no-reset-on-init;
-	ti,no-idle-on-init;
-};
-
-&tscadc {
-	status = "okay";
-	tsc {
-		ti,wires = <4>;
-		ti,x-plate-resistance = <200>;
-		ti,zx-cutoff-ratio = <40>;
-		ti,min_deviation = <60>;
-		ti,max_deviation = <600>;
-		ti,coordinate-readouts = <5>;
-		ti,wire-config = <0x00 0x11 0x22 0x33>;
-
-		bnr-buttons {
-			Home-Button {};
-		};
-	};
-
-	adc {
-		ti,adc-channels = <5 6 7>;
-	};
-};
-
-&timer6 {		/* used for cpsw end device */
-	status = "okay";
-	ti,no-reset-on-init;
-	ti,no-idle-on-init;
-};
-
-&timer7 {		/* used for cpsw end device */
-	status = "okay";
-	ti,no-reset-on-init;
-	ti,no-idle-on-init;
-};
-
-&wdt2 {
-	status = "okay";
-	ti,no-reset-on-init;
-	ti,no-idle-on-init;
-};
-
-&epwmss0 {
-	status = "okay";
-};
-
-&tscadc {
-	status = "okay";
-};
-
-&dcan0 {
-	status = "okay";
-};
-
-&dcan1 {
-	status = "okay";
-};
-
-&sham {
-	status = "disabled";
-};
-
-&aes {
-	status = "disabled";
-};
-
-&rng {
-	status = "disabled";
-};
diff --git a/board/BuR/brppt1/board.c b/board/BuR/brppt1/board.c
index 7df37e4..c8dc186 100644
--- a/board/BuR/brppt1/board.c
+++ b/board/BuR/brppt1/board.c
@@ -151,9 +151,7 @@
 	hw_watchdog_init();
 #endif
 	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
-#ifdef CONFIG_MTD_RAW_NAND
-	gpmc_init();
-#endif
+
 	return 0;
 }
 
diff --git a/board/BuR/brppt1/mux.c b/board/BuR/brppt1/mux.c
index b863d37..5d2c7a2 100644
--- a/board/BuR/brppt1/mux.c
+++ b/board/BuR/brppt1/mux.c
@@ -26,6 +26,7 @@
 	{OFFSET(uart0_txd), (MODE(0) | PULLUDEN)},
 	{-1},
 };
+
 static struct module_pin_mux uart1_pin_mux[] = {
 	/* UART1_RTS as I2C2-SCL */
 	{OFFSET(uart1_rtsn), (MODE(3) | PULLUDEN | PULLUP_EN | RXACTIVE)},
@@ -37,7 +38,7 @@
 	{OFFSET(uart1_txd), (MODE(0) | PULLUDEN)},
 	{-1},
 };
-#ifdef CONFIG_MMC
+
 static struct module_pin_mux mmc1_pin_mux[] = {
 	{OFFSET(gpmc_ad7), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT7 */
 	{OFFSET(gpmc_ad6), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT6 */
@@ -54,7 +55,7 @@
 	{OFFSET(gpmc_advn_ale), (MODE(7) | RXACTIVE | PULLUP_EN)},/* MMC1_CD */
 	{-1},
 };
-#endif
+
 static struct module_pin_mux i2c0_pin_mux[] = {
 	/* I2C_DATA */
 	{OFFSET(i2c0_sda), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)},
@@ -118,26 +119,7 @@
 	{OFFSET(gpmc_be1n), (MODE(1) | RXACTIVE)},/* MII1_COL */
 	{-1},
 };
-#ifdef CONFIG_MTD_RAW_NAND
-static struct module_pin_mux nand_pin_mux[] = {
-	{OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD0 */
-	{OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD1 */
-	{OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD2 */
-	{OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD3 */
-	{OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD4 */
-	{OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD5 */
-	{OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD6 */
-	{OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD7 */
-	{OFFSET(gpmc_clk), (MODE(2) | RXACTIVE | PULLUP_EN)},	/* NAND WAIT */
-	{OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)},	/* NAND_WPN */
-	{OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)},	/* NAND_CS0 */
-	{OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)},	/* NAND_ADV_ALE */
-	{OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)},	/* NAND_OE */
-	{OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)},	/* NAND_WEN */
-	{OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)},	/* NAND_BE_CLE */
-	{-1},
-};
-#endif
+
 static struct module_pin_mux gpIOs[] = {
 	/* GPIO0_6  (SPI0_CS1) - 3v3_PWR_nEN (Display Power Supply) */
 	{OFFSET(spi0_cs1),  (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
@@ -180,14 +162,6 @@
 	{OFFSET(mcasp0_axr0),  (MODE(7) | PULLUDDIS) },
 	/* GPIO3_17 (MCASP0_AHCLKR) - ETH2_LEDY */
 	{OFFSET(mcasp0_ahclkr), (MODE(7) | PULLUDDIS) },
-#ifndef CONFIG_MTD_RAW_NAND
-	/* GPIO2_3 - NAND_OE */
-	{OFFSET(gpmc_oen_ren), (MODE(7) | PULLDOWN_EN | RXACTIVE)},
-	/* GPIO2_4 - NAND_WEN */
-	{OFFSET(gpmc_wen), (MODE(7) | PULLDOWN_EN | RXACTIVE)},
-	/* GPIO2_5 - NAND_BE_CLE */
-	{OFFSET(gpmc_be0n_cle), (MODE(7) | PULLDOWN_EN | RXACTIVE)},
-#endif
 	{-1},
 };
 
@@ -222,7 +196,6 @@
 	{OFFSET(lcd_hsync), (MODE(0) | PULLUDDIS)},	/* LCD-HSync */
 	{OFFSET(lcd_ac_bias_en), (MODE(0) | PULLUDDIS)},/* LCD-DE */
 	{OFFSET(lcd_pclk), (MODE(0) | PULLUDDIS)},	/* LCD-CLK */
-
 	{-1},
 };
 
@@ -241,11 +214,7 @@
 	configure_module_pin_mux(i2c0_pin_mux);
 	configure_module_pin_mux(mii1_pin_mux);
 	configure_module_pin_mux(mii2_pin_mux);
-#ifdef CONFIG_MTD_RAW_NAND
-	configure_module_pin_mux(nand_pin_mux);
-#elif defined(CONFIG_MMC)
 	configure_module_pin_mux(mmc1_pin_mux);
-#endif
 	configure_module_pin_mux(spi0_pin_mux);
 	configure_module_pin_mux(lcd_pin_mux);
 	configure_module_pin_mux(uart1_pin_mux);
diff --git a/configs/brppt1_nand_defconfig b/configs/brppt1_nand_defconfig
deleted file mode 100644
index c5981ba..0000000
--- a/configs/brppt1_nand_defconfig
+++ /dev/null
@@ -1,122 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_OMAP2PLUS=y
-CONFIG_SYS_MALLOC_LEN=0x500000
-CONFIG_SPL_GPIO=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_ENV_SIZE=0x10000
-CONFIG_ENV_OFFSET=0x60000
-CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="am335x-brppt1-nand"
-CONFIG_AM33XX=y
-CONFIG_TARGET_BRPPT1=y
-CONFIG_SPL_SERIAL=y
-CONFIG_SPL=y
-CONFIG_SYS_LOAD_ADDR=0x80000000
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00
-# CONFIG_EXPERT is not set
-# CONFIG_FIT is not set
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_BOOTDELAY=0
-CONFIG_USE_BOOTCOMMAND=y
-CONFIG_BOOTCOMMAND="run b_default"
-CONFIG_USE_PREBOOT=y
-CONFIG_PREBOOT="run cfgscr; run brdefaultip"
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
-CONFIG_SYS_CONSOLE_INFO_QUIET=y
-# CONFIG_DISPLAY_CPUINFO is not set
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_ARCH_MISC_INIT=y
-CONFIG_SPL_SYS_MALLOC_SIMPLE=y
-CONFIG_SYS_SPL_MALLOC=y
-CONFIG_SYS_SPL_MALLOC_SIZE=0x500000
-# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set
-CONFIG_SPL_I2C=y
-CONFIG_SPL_NAND_DRIVERS=y
-CONFIG_SPL_NAND_ECC=y
-CONFIG_SPL_NAND_BASE=y
-CONFIG_SPL_POWER=y
-CONFIG_SPL_WATCHDOG=y
-CONFIG_SPL_YMODEM_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_CBSIZE=512
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_BOOTZ=y
-CONFIG_SYS_BOOTM_LEN=0x2000000
-# CONFIG_CMD_IMI is not set
-# CONFIG_CMD_XIMG is not set
-# CONFIG_CMD_EDITENV is not set
-# CONFIG_CMD_CRC32 is not set
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_I2C=y
-# CONFIG_CMD_LOADS is not set
-CONFIG_CMD_NAND=y
-CONFIG_CMD_PART=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_ITEST is not set
-CONFIG_CMD_DHCP=y
-CONFIG_BOOTP_MAY_FAIL=y
-# CONFIG_CMD_NFS is not set
-CONFIG_SYS_DISABLE_AUTOLOAD=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_BOOTCOUNT=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_TIME=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nand0=omap2-nand.0"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=omap2-nand.0:128k(MLO),128k(cfgscr),128k(dtb),128k(u-boot-env),512k(u-boot),4m(kernel),128m(rootfs),-(user)"
-# CONFIG_SPL_DOS_PARTITION is not set
-CONFIG_OF_CONTROL=y
-CONFIG_SPL_OF_CONTROL=y
-CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clocks clock-names interrupt-parent interrupt-controller interrupt-cells dma-names dmas "
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_NAND=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_VERSION_VARIABLE=y
-CONFIG_NET_RETRY_COUNT=10
-CONFIG_BOOTP_SEND_HOSTNAME=y
-CONFIG_NET_RANDOM_ETHADDR=y
-CONFIG_NETCONSOLE=y
-CONFIG_DM=y
-CONFIG_SPL_DM=y
-CONFIG_SPL_DM_SEQ_ALIAS=y
-# CONFIG_OF_TRANSLATE is not set
-CONFIG_BOOTCOUNT_LIMIT=y
-CONFIG_DM_I2C=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_MISC=y
-# CONFIG_MMC is not set
-CONFIG_MTD=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_SYS_NAND_BLOCK_SIZE=0x20000
-CONFIG_SYS_NAND_PAGE_COUNT=0x40
-CONFIG_SYS_NAND_PAGE_SIZE=0x800
-CONFIG_SYS_NAND_OOBSIZE=0x40
-CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
-CONFIG_SYS_NAND_U_BOOT_OFFS=0x80000
-CONFIG_PHY_NATSEMI=y
-CONFIG_DRIVER_TI_CPSW=y
-CONFIG_DM_PMIC=y
-# CONFIG_SPL_DM_PMIC is not set
-CONFIG_PMIC_TPS65217=y
-CONFIG_DM_SERIAL=y
-CONFIG_USB=y
-CONFIG_USB_MUSB_HOST=y
-CONFIG_USB_MUSB_GADGET=y
-CONFIG_USB_MUSB_TI=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_GADGET=y
-CONFIG_FAT_WRITE=y
-CONFIG_LZO=y
-# CONFIG_OF_LIBFDT_OVERLAY is not set
-# CONFIG_EFI_LOADER is not set
diff --git a/configs/brppt1_spi_defconfig b/configs/brppt1_spi_defconfig
deleted file mode 100644
index fa6b840..0000000
--- a/configs/brppt1_spi_defconfig
+++ /dev/null
@@ -1,130 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_OMAP2PLUS=y
-CONFIG_SYS_MALLOC_LEN=0x500000
-CONFIG_SYS_MALLOC_F_LEN=0x4000
-CONFIG_SPL_GPIO=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_ENV_SIZE=0x10000
-CONFIG_ENV_OFFSET=0x20000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_DM_GPIO=y
-CONFIG_SPL_DM_SPI=y
-CONFIG_DEFAULT_DEVICE_TREE="am335x-brppt1-spi"
-CONFIG_AM33XX=y
-CONFIG_TARGET_BRPPT1=y
-CONFIG_SPL_SERIAL=y
-CONFIG_SPL=y
-CONFIG_ENV_OFFSET_REDUND=0x30000
-CONFIG_SPL_SPI_FLASH_SUPPORT=y
-CONFIG_SPL_SPI=y
-CONFIG_SYS_LOAD_ADDR=0x80000000
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00
-# CONFIG_EXPERT is not set
-# CONFIG_FIT is not set
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_SPI_BOOT=y
-CONFIG_BOOTDELAY=0
-CONFIG_USE_BOOTCOMMAND=y
-CONFIG_BOOTCOMMAND="run b_default"
-CONFIG_USE_PREBOOT=y
-CONFIG_PREBOOT="run cfgscr; run brdefaultip"
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
-CONFIG_SYS_CONSOLE_INFO_QUIET=y
-# CONFIG_DISPLAY_CPUINFO is not set
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_ARCH_MISC_INIT=y
-CONFIG_SPL_SYS_MALLOC_SIMPLE=y
-CONFIG_SYS_SPL_MALLOC=y
-CONFIG_SYS_SPL_MALLOC_SIZE=0x500000
-# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set
-CONFIG_SPL_I2C=y
-# CONFIG_SPL_NAND_SUPPORT is not set
-CONFIG_SPL_DM_SPI_FLASH=y
-CONFIG_SPL_POWER=y
-CONFIG_SPL_SPI_LOAD=y
-CONFIG_SYS_SPI_U_BOOT_OFFS=0x40000
-CONFIG_SPL_WATCHDOG=y
-CONFIG_SPL_YMODEM_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_CBSIZE=512
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_BOOTZ=y
-CONFIG_SYS_BOOTM_LEN=0x2000000
-# CONFIG_CMD_IMI is not set
-# CONFIG_CMD_XIMG is not set
-# CONFIG_CMD_EDITENV is not set
-# CONFIG_CMD_CRC32 is not set
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_I2C=y
-# CONFIG_CMD_LOADS is not set
-CONFIG_CMD_MMC=y
-CONFIG_CMD_BKOPS_ENABLE=y
-CONFIG_CMD_PART=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_ITEST is not set
-CONFIG_CMD_DHCP=y
-CONFIG_BOOTP_MAY_FAIL=y
-# CONFIG_CMD_NFS is not set
-CONFIG_SYS_DISABLE_AUTOLOAD=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_BOOTCOUNT=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_TIME=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-# CONFIG_SPL_DOS_PARTITION is not set
-CONFIG_OF_CONTROL=y
-CONFIG_SPL_OF_CONTROL=y
-CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clocks clock-names interrupt-parent interrupt-controller interrupt-cells dma-names dmas "
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_VERSION_VARIABLE=y
-CONFIG_NET_RETRY_COUNT=10
-CONFIG_BOOTP_SEND_HOSTNAME=y
-CONFIG_NET_RANDOM_ETHADDR=y
-CONFIG_NETCONSOLE=y
-CONFIG_DM=y
-CONFIG_SPL_DM=y
-CONFIG_SPL_DM_SEQ_ALIAS=y
-# CONFIG_OF_TRANSLATE is not set
-CONFIG_BOOTCOUNT_LIMIT=y
-CONFIG_DM_I2C=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_MISC=y
-CONFIG_MMC_OMAP_HS=y
-CONFIG_MTD=y
-CONFIG_DM_SPI_FLASH=y
-CONFIG_SF_DEFAULT_SPEED=24000000
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_WINBOND=y
-# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
-CONFIG_PHY_NATSEMI=y
-CONFIG_DRIVER_TI_CPSW=y
-CONFIG_DM_PMIC=y
-# CONFIG_SPL_DM_PMIC is not set
-CONFIG_PMIC_TPS65217=y
-CONFIG_DM_SERIAL=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_OMAP3_SPI=y
-CONFIG_USB=y
-CONFIG_USB_MUSB_HOST=y
-CONFIG_USB_MUSB_GADGET=y
-CONFIG_USB_MUSB_TI=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_GADGET=y
-CONFIG_FAT_WRITE=y
-CONFIG_LZO=y
-# CONFIG_OF_LIBFDT_OVERLAY is not set
-# CONFIG_EFI_LOADER is not set
diff --git a/include/configs/brppt1.h b/include/configs/brppt1.h
index 6cb1a10..481473a 100644
--- a/include/configs/brppt1.h
+++ b/include/configs/brppt1.h
@@ -27,31 +27,7 @@
  * the Linux kernel.
  */
 
-#ifdef CONFIG_SPL_OS_BOOT
-/* RAW SD card / eMMC */
-
-#endif /* CONFIG_SPL_OS_BOOT */
-
-#ifdef CONFIG_MTD_RAW_NAND
-#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
-#endif /* CONFIG_MTD_RAW_NAND */
-
-#ifdef CONFIG_MTD_RAW_NAND
-#define NANDTGTS \
-"cfgscr=mw ${dtbaddr} 0; nand read ${cfgaddr} cfgscr && source ${cfgaddr};" \
-" fdt addr ${dtbaddr} || cp ${fdtcontroladdr} ${dtbaddr} 4000\0" \
-"nandargs=setenv bootargs console=${console} ${optargs} ${optargs_rot} " \
-	"root=mtd6 rootfstype=jffs2 b_mode=${b_mode}\0" \
-"b_nand=nand read ${loadaddr} kernel; nand read ${dtbaddr} dtb; " \
-	"run nandargs; run cfgscr; bootz ${loadaddr} - ${dtbaddr}\0" \
-"b_tgts_std=usb0 nand net\0" \
-"b_tgts_rcy=net usb0 nand\0" \
-"b_tgts_pme=usb0 nand net\0"
-#else
-#define NANDTGTS ""
-#endif /* CONFIG_MTD_RAW_NAND */
-
-#define MMCSPI_TGTS \
+#define MMC_TGTS \
 "t30args#0=setenv bootargs ${optargs_rot} ${optargs} console=${console} " \
 	"b_mode=${b_mode} root=/dev/mmcblk0p2 rootfstype=ext4\0" \
 "b_t30lgcy#0=" \
@@ -76,7 +52,7 @@
 
 #ifdef CONFIG_ENV_IS_IN_MMC
 #define MMCTGTS \
-MMCSPI_TGTS \
+MMC_TGTS \
 "cfgscr=mw ${dtbaddr} 0;" \
 " mmc dev 1; mmc read ${cfgaddr} 200 80; source ${cfgaddr};" \
 " fdt addr ${dtbaddr} || cp ${fdtcontroladdr} ${dtbaddr} 4000\0"
@@ -84,16 +60,6 @@
 #define MMCTGTS ""
 #endif /* CONFIG_MMC */
 
-#ifdef CONFIG_SPI
-#define SPITGTS \
-MMCSPI_TGTS \
-"cfgscr=mw ${dtbaddr} 0;" \
-" sf probe; sf read ${cfgaddr} 0xC0000 10000; source ${cfgaddr};" \
-" fdt addr ${dtbaddr} || cp ${fdtcontroladdr} ${dtbaddr} 4000\0"
-#else
-#define SPITGTS ""
-#endif /* CONFIG_SPI */
-
 #define LOAD_OFFSET(x)			0x8##x
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
@@ -110,8 +76,6 @@
 "b_usb0=usb start && load usb 0 ${scraddr} bootscr.img && source ${scraddr}\0" \
 "b_net=tftp ${scraddr} netscript.img && source ${scraddr}\0" \
 MMCTGTS \
-SPITGTS \
-NANDTGTS \
 "b_deftgts=if test ${b_mode} = 12; then setenv b_tgts ${b_tgts_pme};" \
 " elif test ${b_mode} = 0; then setenv b_tgts ${b_tgts_rcy};" \
 " else setenv b_tgts ${b_tgts_std}; fi\0" \
@@ -119,28 +83,4 @@
 " do echo \"### booting ${target} ###\"; run b_${target};" \
 " if test ${b_break} = 1; then; exit; fi; done\0"
 
-#ifdef CONFIG_MTD_RAW_NAND
-/*
- * GPMC  block.  We support 1 device and the physical address to
- * access CS0 at is 0x8000000.
- */
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_SYS_NAND_BASE		0x8000000
-/* don't change OMAP_ELM, ECCSCHEME. ROM code only supports this */
-#define CONFIG_SYS_NAND_ECCPOS		{2, 3, 4, 5, 6, 7, 8, 9, \
-					10, 11, 12, 13, 14, 15, 16, 17, \
-					18, 19, 20, 21, 22, 23, 24, 25, \
-					26, 27, 28, 29, 30, 31, 32, 33, \
-					34, 35, 36, 37, 38, 39, 40, 41, \
-					42, 43, 44, 45, 46, 47, 48, 49, \
-					50, 51, 52, 53, 54, 55, 56, 57, }
-
-#define CONFIG_SYS_NAND_ECCSIZE		512
-#define CONFIG_SYS_NAND_ECCBYTES	14
-
-#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
-
-#define CONFIG_NAND_OMAP_GPMC_WSCFG	1
-#endif /* CONFIG_MTD_RAW_NAND */
-
 #endif	/* ! __CONFIG_BRPPT1_H__ */