Merge tag 'mips-fixes-for-2019.07' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips
- mtmips: network stability fixes for gardena-smart-gateway
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 68f17c1..20dbc2f 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -737,14 +737,19 @@
at91-vinco.dtb
dtb-$(CONFIG_ARCH_BCM283X) += \
- bcm2835-rpi-a-plus.dtb \
bcm2835-rpi-a.dtb \
+ bcm2835-rpi-a-plus.dtb \
+ bcm2835-rpi-b.dtb \
bcm2835-rpi-b-plus.dtb \
bcm2835-rpi-b-rev2.dtb \
- bcm2835-rpi-b.dtb \
- bcm2835-rpi-zero-w.dtb \
+ bcm2835-rpi-cm1-io1.dtb \
+ bcm2835-rpi-zero.dtb \
+ bcm2835-rpi-zero-w.dtb\
bcm2836-rpi-2-b.dtb \
- bcm2837-rpi-3-b.dtb
+ bcm2837-rpi-3-a-plus.dtb \
+ bcm2837-rpi-3-b.dtb \
+ bcm2837-rpi-3-b-plus.dtb \
+ bcm2837-rpi-cm3-io3.dtb
dtb-$(CONFIG_ARCH_BCM63158) += \
bcm963158.dtb
diff --git a/arch/arm/dts/bcm2835-rpi-a-plus.dts b/arch/arm/dts/bcm2835-rpi-a-plus.dts
index 9f86649..db8a601 100644
--- a/arch/arm/dts/bcm2835-rpi-a-plus.dts
+++ b/arch/arm/dts/bcm2835-rpi-a-plus.dts
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
@@ -9,12 +10,12 @@
leds {
act {
- gpios = <&gpio 47 0>;
+ gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
};
pwr {
label = "PWR";
- gpios = <&gpio 35 0>;
+ gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
default-state = "keep";
linux,default-trigger = "default-on";
};
@@ -30,8 +31,8 @@
* "FOO" = GPIO line named "FOO" on the schematic
* "FOO_N" = GPIO line named "FOO" on schematic, active low
*/
- gpio-line-names = "SDA0",
- "SCL0",
+ gpio-line-names = "ID_SDA",
+ "ID_SCL",
"SDA1",
"SCL1",
"GPIO_GCLK",
@@ -100,6 +101,12 @@
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio14>;
diff --git a/arch/arm/dts/bcm2835-rpi-a.dts b/arch/arm/dts/bcm2835-rpi-a.dts
index 4b1af06..067d1f0 100644
--- a/arch/arm/dts/bcm2835-rpi-a.dts
+++ b/arch/arm/dts/bcm2835-rpi-a.dts
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
@@ -9,7 +10,7 @@
leds {
act {
- gpios = <&gpio 16 1>;
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
};
};
};
@@ -95,6 +96,12 @@
hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
};
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio14>;
diff --git a/arch/arm/dts/bcm2835-rpi-b-plus.dts b/arch/arm/dts/bcm2835-rpi-b-plus.dts
index a846f1e..1e40d67 100644
--- a/arch/arm/dts/bcm2835-rpi-b-plus.dts
+++ b/arch/arm/dts/bcm2835-rpi-b-plus.dts
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
@@ -10,12 +11,12 @@
leds {
act {
- gpios = <&gpio 47 0>;
+ gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
};
pwr {
label = "PWR";
- gpios = <&gpio 35 0>;
+ gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
default-state = "keep";
linux,default-trigger = "default-on";
};
@@ -32,8 +33,8 @@
* "FOO" = GPIO line named "FOO" on the schematic
* "FOO_N" = GPIO line named "FOO" on schematic, active low
*/
- gpio-line-names = "SDA0",
- "SCL0",
+ gpio-line-names = "ID_SDA",
+ "ID_SCL",
"SDA1",
"SCL1",
"GPIO_GCLK",
@@ -102,6 +103,12 @@
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio14>;
diff --git a/arch/arm/dts/bcm2835-rpi-b-rev2.dts b/arch/arm/dts/bcm2835-rpi-b-rev2.dts
index e860964..28e7513 100644
--- a/arch/arm/dts/bcm2835-rpi-b-rev2.dts
+++ b/arch/arm/dts/bcm2835-rpi-b-rev2.dts
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
@@ -10,7 +11,7 @@
leds {
act {
- gpios = <&gpio 16 1>;
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
};
};
};
@@ -92,7 +93,13 @@
};
&hdmi {
- hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+ hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+ status = "okay";
};
&uart0 {
diff --git a/arch/arm/dts/bcm2835-rpi-b.dts b/arch/arm/dts/bcm2835-rpi-b.dts
index 5d77f3f..31ff602 100644
--- a/arch/arm/dts/bcm2835-rpi-b.dts
+++ b/arch/arm/dts/bcm2835-rpi-b.dts
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
@@ -10,7 +11,7 @@
leds {
act {
- gpios = <&gpio 16 1>;
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
};
};
};
@@ -90,6 +91,12 @@
hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
};
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio14>;
diff --git a/arch/arm/dts/bcm2835-rpi-cm1-io1.dts b/arch/arm/dts/bcm2835-rpi-cm1-io1.dts
new file mode 100644
index 0000000..4764a25
--- /dev/null
+++ b/arch/arm/dts/bcm2835-rpi-cm1-io1.dts
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2835-rpi-cm1.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+ compatible = "raspberrypi,compute-module", "brcm,bcm2835";
+ model = "Raspberry Pi Compute Module IO board rev1";
+};
+
+&gpio {
+ /*
+ * This is based on the official GPU firmware DT blob.
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "GPIO0",
+ "GPIO1",
+ "GPIO2",
+ "GPIO3",
+ "GPIO4",
+ "GPIO5",
+ "GPIO6",
+ "GPIO7",
+ "GPIO8",
+ "GPIO9",
+ "GPIO10",
+ "GPIO11",
+ "GPIO12",
+ "GPIO13",
+ "GPIO14",
+ "GPIO15",
+ "GPIO16",
+ "GPIO17",
+ "GPIO18",
+ "GPIO19",
+ "GPIO20",
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "GPIO26",
+ "GPIO27",
+ "GPIO28",
+ "GPIO29",
+ "GPIO30",
+ "GPIO31",
+ "GPIO32",
+ "GPIO33",
+ "GPIO34",
+ "GPIO35",
+ "GPIO36",
+ "GPIO37",
+ "GPIO38",
+ "GPIO39",
+ "GPIO40",
+ "GPIO41",
+ "GPIO42",
+ "GPIO43",
+ "GPIO44",
+ "GPIO45",
+ "HDMI_HPD_N",
+ /* Also used as ACT LED */
+ "EMMC_EN_N",
+ /* Used by eMMC */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+
+ pinctrl-0 = <&gpioout &alt0>;
+};
+
+&hdmi {
+ hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_gpio14>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/bcm2835-rpi-cm1.dtsi b/arch/arm/dts/bcm2835-rpi-cm1.dtsi
new file mode 100644
index 0000000..ef22c2d
--- /dev/null
+++ b/arch/arm/dts/bcm2835-rpi-cm1.dtsi
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2835.dtsi"
+#include "bcm2835-rpi.dtsi"
+
+/ {
+ leds {
+ act {
+ gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ reg_3v3: fixed-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_1v8: fixed-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+};
+
+&sdhost {
+ non-removable;
+ vmmc-supply = <®_3v3>;
+ vqmmc-supply = <®_1v8>;
+};
diff --git a/arch/arm/dts/bcm2835-rpi-zero-w.dts b/arch/arm/dts/bcm2835-rpi-zero-w.dts
index 7817054..ba0167d 100644
--- a/arch/arm/dts/bcm2835-rpi-zero-w.dts
+++ b/arch/arm/dts/bcm2835-rpi-zero-w.dts
@@ -1,26 +1,135 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2017 Stefan Wahren <stefan.wahren@i2se.com>
+ */
+
/dts-v1/;
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
-#include "bcm283x-rpi-smsc9512.dtsi"
-#include "bcm283x-rpi-usb-host.dtsi"
+#include "bcm283x-rpi-usb-otg.dtsi"
/ {
compatible = "raspberrypi,model-zero-w", "brcm,bcm2835";
model = "Raspberry Pi Zero W";
+ chosen {
+ /* 8250 auxiliary UART instead of pl011 */
+ stdout-path = "serial1:115200n8";
+ };
+
leds {
act {
- gpios = <&gpio 47 0>;
+ gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
};
};
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
+ };
};
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart1_gpio14>;
- status = "okay";
+&gpio {
+ /*
+ * This is based on the official GPU firmware DT blob.
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "ID_SDA",
+ "ID_SCL",
+ "SDA1",
+ "SCL1",
+ "GPIO_GCLK",
+ "GPIO5",
+ "GPIO6",
+ "SPI_CE1_N",
+ "SPI_CE0_N",
+ "SPI_MISO",
+ "SPI_MOSI",
+ "SPI_SCLK",
+ "GPIO12",
+ "GPIO13",
+ /* Serial port */
+ "TXD0",
+ "RXD0",
+ "GPIO16",
+ "GPIO17",
+ "GPIO18",
+ "GPIO19",
+ "GPIO20",
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "GPIO26",
+ "GPIO27",
+ "SDA0",
+ "SCL0",
+ "NC", /* GPIO30 */
+ "NC", /* GPIO31 */
+ "NC", /* GPIO32 */
+ "NC", /* GPIO33 */
+ "NC", /* GPIO34 */
+ "NC", /* GPIO35 */
+ "NC", /* GPIO36 */
+ "NC", /* GPIO37 */
+ "NC", /* GPIO38 */
+ "NC", /* GPIO39 */
+ "CAM_GPIO1", /* GPIO40 */
+ "WL_ON", /* GPIO41 */
+ "NC", /* GPIO42 */
+ "WIFI_CLK", /* GPIO43 */
+ "CAM_GPIO0", /* GPIO44 */
+ "BT_ON", /* GPIO45 */
+ "HDMI_HPD_N",
+ "STATUS_LED_N",
+ /* Used by SD Card */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+
+ pinctrl-0 = <&gpioout &alt0>;
};
&hdmi {
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
+
+&sdhci {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&emmc_gpio34 &gpclk2_gpio43>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ non-removable;
+ status = "okay";
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_gpio32 &uart0_ctsrts_gpio30>;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <2000000>;
+ shutdown-gpios = <&gpio 45 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_gpio14>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/bcm2835-rpi-zero.dts b/arch/arm/dts/bcm2835-rpi-zero.dts
new file mode 100644
index 0000000..3b35a8a
--- /dev/null
+++ b/arch/arm/dts/bcm2835-rpi-zero.dts
@@ -0,0 +1,105 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2016 Stefan Wahren <stefan.wahren@i2se.com>
+ */
+
+/dts-v1/;
+#include "bcm2835.dtsi"
+#include "bcm2835-rpi.dtsi"
+#include "bcm283x-rpi-usb-otg.dtsi"
+
+/ {
+ compatible = "raspberrypi,model-zero", "brcm,bcm2835";
+ model = "Raspberry Pi Zero";
+
+ leds {
+ act {
+ gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&gpio {
+ /*
+ * This is based on the official GPU firmware DT blob.
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "ID_SDA",
+ "ID_SCL",
+ "SDA1",
+ "SCL1",
+ "GPIO_GCLK",
+ "GPIO5",
+ "GPIO6",
+ "SPI_CE1_N",
+ "SPI_CE0_N",
+ "SPI_MISO",
+ "SPI_MOSI",
+ "SPI_SCLK",
+ "GPIO12",
+ "GPIO13",
+ /* Serial port */
+ "TXD0",
+ "RXD0",
+ "GPIO16",
+ "GPIO17",
+ "GPIO18",
+ "GPIO19",
+ "GPIO20",
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "GPIO26",
+ "GPIO27",
+ "SDA0",
+ "SCL0",
+ "NC", /* GPIO30 */
+ "NC", /* GPIO31 */
+ "CAM_GPIO1", /* GPIO32 */
+ "NC", /* GPIO33 */
+ "NC", /* GPIO34 */
+ "NC", /* GPIO35 */
+ "NC", /* GPIO36 */
+ "NC", /* GPIO37 */
+ "NC", /* GPIO38 */
+ "NC", /* GPIO39 */
+ "NC", /* GPIO40 */
+ "CAM_GPIO0", /* GPIO41 */
+ "NC", /* GPIO42 */
+ "NC", /* GPIO43 */
+ "NC", /* GPIO44 */
+ "NC", /* GPIO45 */
+ "HDMI_HPD_N",
+ "STATUS_LED_N",
+ /* Used by SD Card */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+
+ pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
+
+ /* I2S interface */
+ i2s_alt0: i2s_alt0 {
+ brcm,pins = <18 19 20 21>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+};
+
+&hdmi {
+ hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_gpio14>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/bcm2835-rpi.dtsi b/arch/arm/dts/bcm2835-rpi.dtsi
index 8b95832..715d50c 100644
--- a/arch/arm/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/dts/bcm2835-rpi.dtsi
@@ -1,7 +1,7 @@
#include <dt-bindings/power/raspberrypi-power.h>
/ {
- memory {
+ memory@0 {
device_type = "memory";
reg = <0 0x10000000>;
};
@@ -18,7 +18,7 @@
soc {
firmware: firmware {
- compatible = "raspberrypi,bcm2835-firmware";
+ compatible = "raspberrypi,bcm2835-firmware", "simple-bus";
mboxes = <&mailbox>;
};
@@ -27,6 +27,12 @@
firmware = <&firmware>;
#power-domain-cells = <1>;
};
+
+ vchiq: mailbox@7e00b840 {
+ compatible = "brcm,bcm2835-vchiq";
+ reg = <0x7e00b840 0x3c>;
+ interrupts = <0 2>;
+ };
};
};
@@ -65,30 +71,20 @@
&sdhci {
pinctrl-names = "default";
pinctrl-0 = <&emmc_gpio48>;
- status = "okay";
bus-width = <4>;
};
&sdhost {
pinctrl-names = "default";
pinctrl-0 = <&sdhost_gpio48>;
- bus-width = <4>;
-};
-
-&pwm {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
status = "okay";
+ bus-width = <4>;
};
&usb {
power-domains = <&power RPI_POWER_DOMAIN_USB>;
};
-&v3d {
- power-domains = <&power RPI_POWER_DOMAIN_V3D>;
-};
-
&hdmi {
power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
status = "okay";
diff --git a/arch/arm/dts/bcm2835.dtsi b/arch/arm/dts/bcm2835.dtsi
index 659b6e9..a5c3824 100644
--- a/arch/arm/dts/bcm2835.dtsi
+++ b/arch/arm/dts/bcm2835.dtsi
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
#include "bcm283x.dtsi"
/ {
@@ -17,10 +18,10 @@
soc {
ranges = <0x7e000000 0x20000000 0x02000000>;
dma-ranges = <0x40000000 0x00000000 0x20000000>;
+ };
- arm-pmu {
- compatible = "arm,arm1176-pmu";
- };
+ arm-pmu {
+ compatible = "arm,arm1176-pmu";
};
};
diff --git a/arch/arm/dts/bcm2836-rpi-2-b.dts b/arch/arm/dts/bcm2836-rpi-2-b.dts
index e8de414..7b4e651 100644
--- a/arch/arm/dts/bcm2836-rpi-2-b.dts
+++ b/arch/arm/dts/bcm2836-rpi-2-b.dts
@@ -1,6 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "bcm2836.dtsi"
-#include "bcm2835-rpi.dtsi"
+#include "bcm2836-rpi.dtsi"
#include "bcm283x-rpi-smsc9514.dtsi"
#include "bcm283x-rpi-usb-host.dtsi"
@@ -8,18 +9,18 @@
compatible = "raspberrypi,2-model-b", "brcm,bcm2836";
model = "Raspberry Pi 2 Model B";
- memory {
+ memory@0 {
reg = <0 0x40000000>;
};
leds {
act {
- gpios = <&gpio 47 0>;
+ gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
};
pwr {
label = "PWR";
- gpios = <&gpio 35 0>;
+ gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
default-state = "keep";
linux,default-trigger = "default-on";
};
@@ -27,6 +28,72 @@
};
&gpio {
+ /*
+ * Taken from rpi_SCH_2b_1p2_reduced.pdf and
+ * the official GPU firmware DT blob.
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "ID_SDA",
+ "ID_SCL",
+ "SDA1",
+ "SCL1",
+ "GPIO_GCLK",
+ "GPIO5",
+ "GPIO6",
+ "SPI_CE1_N",
+ "SPI_CE0_N",
+ "SPI_MISO",
+ "SPI_MOSI",
+ "SPI_SCLK",
+ "GPIO12",
+ "GPIO13",
+ /* Serial port */
+ "TXD0",
+ "RXD0",
+ "GPIO16",
+ "GPIO17",
+ "GPIO18",
+ "GPIO19",
+ "GPIO20",
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "GPIO26",
+ "GPIO27",
+ "SDA0",
+ "SCL0",
+ "", /* GPIO30 */
+ "LAN_RUN",
+ "CAM_GPIO1",
+ "", /* GPIO33 */
+ "", /* GPIO34 */
+ "PWR_LOW_N",
+ "", /* GPIO36 */
+ "", /* GPIO37 */
+ "USB_LIMIT",
+ "", /* GPIO39 */
+ "PWM0_OUT",
+ "CAM_GPIO0",
+ "SMPS_SCL",
+ "SMPS_SDA",
+ "ETHCLK",
+ "PWM1_OUT",
+ "HDMI_HPD_N",
+ "STATUS_LED",
+ /* Used by SD Card */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+
pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
/* I2S interface */
@@ -40,6 +107,12 @@
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio14>;
diff --git a/arch/arm/dts/bcm2836-rpi.dtsi b/arch/arm/dts/bcm2836-rpi.dtsi
new file mode 100644
index 0000000..c4c858b
--- /dev/null
+++ b/arch/arm/dts/bcm2836-rpi.dtsi
@@ -0,0 +1,6 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "bcm2835-rpi.dtsi"
+
+&vchiq {
+ compatible = "brcm,bcm2836-vchiq", "brcm,bcm2835-vchiq";
+};
diff --git a/arch/arm/dts/bcm2836.dtsi b/arch/arm/dts/bcm2836.dtsi
index 2c26d0b..c933e84 100644
--- a/arch/arm/dts/bcm2836.dtsi
+++ b/arch/arm/dts/bcm2836.dtsi
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
#include "bcm283x.dtsi"
/ {
@@ -8,28 +9,28 @@
<0x40000000 0x40000000 0x00001000>;
dma-ranges = <0xc0000000 0x00000000 0x3f000000>;
- local_intc: local_intc {
+ local_intc: local_intc@40000000 {
compatible = "brcm,bcm2836-l1-intc";
reg = <0x40000000 0x100>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
interrupt-parent = <&local_intc>;
};
+ };
- arm-pmu {
- compatible = "arm,cortex-a7-pmu";
- interrupt-parent = <&local_intc>;
- interrupts = <9>;
- };
+ arm-pmu {
+ compatible = "arm,cortex-a7-pmu";
+ interrupt-parent = <&local_intc>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH>;
};
timer {
compatible = "arm,armv7-timer";
interrupt-parent = <&local_intc>;
- interrupts = <0>, // PHYS_SECURE_PPI
- <1>, // PHYS_NONSECURE_PPI
- <3>, // VIRT_PPI
- <2>; // HYP_PPI
+ interrupts = <0 IRQ_TYPE_LEVEL_HIGH>, // PHYS_SECURE_PPI
+ <1 IRQ_TYPE_LEVEL_HIGH>, // PHYS_NONSECURE_PPI
+ <3 IRQ_TYPE_LEVEL_HIGH>, // VIRT_PPI
+ <2 IRQ_TYPE_LEVEL_HIGH>; // HYP_PPI
always-on;
};
@@ -75,7 +76,7 @@
compatible = "brcm,bcm2836-armctrl-ic";
reg = <0x7e00b200 0x200>;
interrupt-parent = <&local_intc>;
- interrupts = <8>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
};
&cpu_thermal {
diff --git a/arch/arm/dts/bcm2837-rpi-3-a-plus.dts b/arch/arm/dts/bcm2837-rpi-3-a-plus.dts
new file mode 100644
index 0000000..7f4437a
--- /dev/null
+++ b/arch/arm/dts/bcm2837-rpi-3-a-plus.dts
@@ -0,0 +1,175 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+ compatible = "raspberrypi,3-model-a-plus", "brcm,bcm2837";
+ model = "Raspberry Pi 3 Model A+";
+
+ chosen {
+ /* 8250 auxiliary UART instead of pl011 */
+ stdout-path = "serial1:115200n8";
+ };
+
+ memory@0 {
+ reg = <0 0x20000000>;
+ };
+
+ leds {
+ act {
+ gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
+ };
+
+ pwr {
+ label = "PWR";
+ gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&firmware {
+ expgpio: gpio {
+ compatible = "raspberrypi,firmware-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "",
+ "BT_WL_ON",
+ "STATUS_LED_R",
+ "",
+ "",
+ "CAM_GPIO0",
+ "CAM_GPIO1",
+ "";
+ status = "okay";
+ };
+};
+
+&gpio {
+ /*
+ * This is mostly based on the official GPU firmware DT blob.
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "ID_SDA",
+ "ID_SCL",
+ "SDA1",
+ "SCL1",
+ "GPIO_GCLK",
+ "GPIO5",
+ "GPIO6",
+ "SPI_CE1_N",
+ "SPI_CE0_N",
+ "SPI_MISO",
+ "SPI_MOSI",
+ "SPI_SCLK",
+ "GPIO12",
+ "GPIO13",
+ /* Serial port */
+ "TXD1",
+ "RXD1",
+ "GPIO16",
+ "GPIO17",
+ "GPIO18",
+ "GPIO19",
+ "GPIO20",
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "GPIO26",
+ "GPIO27",
+ "HDMI_HPD_N",
+ "STATUS_LED_G",
+ /* Used by BT module */
+ "CTS0",
+ "RTS0",
+ "TXD0",
+ "RXD0",
+ /* Used by Wifi */
+ "SD1_CLK",
+ "SD1_CMD",
+ "SD1_DATA0",
+ "SD1_DATA1",
+ "SD1_DATA2",
+ "SD1_DATA3",
+ "PWM0_OUT",
+ "PWM1_OUT",
+ "", /* GPIO42 */
+ "WIFI_CLK",
+ "SDA0",
+ "SCL0",
+ "SMPS_SCL",
+ "SMPS_SDA",
+ /* Used by SD Card */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+};
+
+&hdmi {
+ hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
+ status = "okay";
+};
+
+/*
+ * SDHCI is used to control the SDIO for wireless
+ *
+ * WL_REG_ON and BT_REG_ON of the CYW43455 Wifi/BT module are driven
+ * by a single GPIO. We can't give GPIO control to one of the drivers,
+ * otherwise the other part would get unexpectedly disturbed.
+ */
+&sdhci {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_gpio34>;
+ status = "okay";
+ bus-width = <4>;
+ non-removable;
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+/* SDHOST is used to drive the SD card */
+&sdhost {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhost_gpio48>;
+ status = "okay";
+ bus-width = <4>;
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <2000000>;
+ };
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_gpio14>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/bcm2837-rpi-3-b-plus.dts b/arch/arm/dts/bcm2837-rpi-3-b-plus.dts
new file mode 100644
index 0000000..c6fa34c
--- /dev/null
+++ b/arch/arm/dts/bcm2837-rpi-3-b-plus.dts
@@ -0,0 +1,178 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-lan7515.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+ compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837";
+ model = "Raspberry Pi 3 Model B+";
+
+ chosen {
+ /* 8250 auxiliary UART instead of pl011 */
+ stdout-path = "serial1:115200n8";
+ };
+
+ memory@0 {
+ reg = <0 0x40000000>;
+ };
+
+ leds {
+ act {
+ gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
+ };
+
+ pwr {
+ label = "PWR";
+ gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&firmware {
+ expgpio: gpio {
+ compatible = "raspberrypi,firmware-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "BT_ON",
+ "WL_ON",
+ "STATUS_LED_R",
+ "LAN_RUN",
+ "",
+ "CAM_GPIO0",
+ "CAM_GPIO1",
+ "";
+ status = "okay";
+ };
+};
+
+&gpio {
+ /*
+ * Taken from rpi_SCH_3bplus_1p0_reduced.pdf and
+ * the official GPU firmware DT blob.
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "ID_SDA",
+ "ID_SCL",
+ "SDA1",
+ "SCL1",
+ "GPIO_GCLK",
+ "GPIO5",
+ "GPIO6",
+ "SPI_CE1_N",
+ "SPI_CE0_N",
+ "SPI_MISO",
+ "SPI_MOSI",
+ "SPI_SCLK",
+ "GPIO12",
+ "GPIO13",
+ /* Serial port */
+ "TXD1",
+ "RXD1",
+ "GPIO16",
+ "GPIO17",
+ "GPIO18",
+ "GPIO19",
+ "GPIO20",
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "GPIO26",
+ "GPIO27",
+ "HDMI_HPD_N",
+ "STATUS_LED_G",
+ /* Used by BT module */
+ "CTS0",
+ "RTS0",
+ "TXD0",
+ "RXD0",
+ /* Used by Wifi */
+ "SD1_CLK",
+ "SD1_CMD",
+ "SD1_DATA0",
+ "SD1_DATA1",
+ "SD1_DATA2",
+ "SD1_DATA3",
+ "PWM0_OUT",
+ "PWM1_OUT",
+ "ETHCLK",
+ "WIFI_CLK",
+ "SDA0",
+ "SCL0",
+ "SMPS_SCL",
+ "SMPS_SDA",
+ /* Used by SD Card */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+};
+
+&hdmi {
+ hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
+ status = "okay";
+};
+
+/* SDHCI is used to control the SDIO for wireless */
+&sdhci {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_gpio34>;
+ status = "okay";
+ bus-width = <4>;
+ non-removable;
+ mmc-pwrseq = <&wifi_pwrseq>;
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+/* SDHOST is used to drive the SD card */
+&sdhost {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhost_gpio48>;
+ status = "okay";
+ bus-width = <4>;
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <2000000>;
+ shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_gpio14>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/bcm2837-rpi-3-b.dts b/arch/arm/dts/bcm2837-rpi-3-b.dts
index 20725ca..ce71f57 100644
--- a/arch/arm/dts/bcm2837-rpi-3-b.dts
+++ b/arch/arm/dts/bcm2837-rpi-3-b.dts
@@ -1,6 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "bcm2837.dtsi"
-#include "bcm2835-rpi.dtsi"
+#include "bcm2836-rpi.dtsi"
#include "bcm283x-rpi-smsc9514.dtsi"
#include "bcm283x-rpi-usb-host.dtsi"
@@ -8,22 +9,135 @@
compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
model = "Raspberry Pi 3 Model B";
- memory {
+ chosen {
+ /* 8250 auxiliary UART instead of pl011 */
+ stdout-path = "serial1:115200n8";
+ };
+
+ memory@0 {
reg = <0 0x40000000>;
};
leds {
act {
- gpios = <&gpio 47 0>;
+ gpios = <&expgpio 2 GPIO_ACTIVE_HIGH>;
};
};
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&firmware {
+ expgpio: gpio {
+ compatible = "raspberrypi,firmware-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "BT_ON",
+ "WL_ON",
+ "STATUS_LED",
+ "LAN_RUN",
+ "HDMI_HPD_N",
+ "CAM_GPIO0",
+ "CAM_GPIO1",
+ "PWR_LOW_N";
+ status = "okay";
+ };
};
+&gpio {
+ /*
+ * Taken from rpi_SCH_3b_1p2_reduced.pdf and
+ * the official GPU firmware DT blob.
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "ID_SDA",
+ "ID_SCL",
+ "SDA1",
+ "SCL1",
+ "GPIO_GCLK",
+ "GPIO5",
+ "GPIO6",
+ "SPI_CE1_N",
+ "SPI_CE0_N",
+ "SPI_MISO",
+ "SPI_MOSI",
+ "SPI_SCLK",
+ "GPIO12",
+ "GPIO13",
+ /* Serial port */
+ "TXD1",
+ "RXD1",
+ "GPIO16",
+ "GPIO17",
+ "GPIO18",
+ "GPIO19",
+ "GPIO20",
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "GPIO26",
+ "GPIO27",
+ "", /* GPIO 28 */
+ "LAN_RUN_BOOT",
+ /* Used by BT module */
+ "CTS0",
+ "RTS0",
+ "TXD0",
+ "RXD0",
+ /* Used by Wifi */
+ "SD1_CLK",
+ "SD1_CMD",
+ "SD1_DATA0",
+ "SD1_DATA1",
+ "SD1_DATA2",
+ "SD1_DATA3",
+ "PWM0_OUT",
+ "PWM1_OUT",
+ "ETHCLK",
+ "WIFI_CLK",
+ "SDA0",
+ "SCL0",
+ "SMPS_SCL",
+ "SMPS_SDA",
+ /* Used by SD Card */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
+ status = "okay";
+};
+
+&hdmi {
+ hpd-gpios = <&expgpio 4 GPIO_ACTIVE_LOW>;
+};
+
/* uart0 communicates with the BT module */
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>;
status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <2000000>;
+ shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+ };
};
/* uart1 is mapped to the pin header */
@@ -35,11 +149,19 @@
/* SDHCI is used to control the SDIO for wireless */
&sdhci {
+ #address-cells = <1>;
+ #size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&emmc_gpio34>;
status = "okay";
bus-width = <4>;
non-removable;
+ mmc-pwrseq = <&wifi_pwrseq>;
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
};
/* SDHOST is used to drive the SD card */
diff --git a/arch/arm/dts/bcm2837-rpi-cm3-io3.dts b/arch/arm/dts/bcm2837-rpi-cm3-io3.dts
new file mode 100644
index 0000000..6c8233a
--- /dev/null
+++ b/arch/arm/dts/bcm2837-rpi-cm3-io3.dts
@@ -0,0 +1,87 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837-rpi-cm3.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+ compatible = "raspberrypi,3-compute-module", "brcm,bcm2837";
+ model = "Raspberry Pi Compute Module 3 IO board V3.0";
+};
+
+&gpio {
+ /*
+ * This is based on the official GPU firmware DT blob.
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "GPIO0",
+ "GPIO1",
+ "GPIO2",
+ "GPIO3",
+ "GPIO4",
+ "GPIO5",
+ "GPIO6",
+ "GPIO7",
+ "GPIO8",
+ "GPIO9",
+ "GPIO10",
+ "GPIO11",
+ "GPIO12",
+ "GPIO13",
+ "GPIO14",
+ "GPIO15",
+ "GPIO16",
+ "GPIO17",
+ "GPIO18",
+ "GPIO19",
+ "GPIO20",
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "GPIO26",
+ "GPIO27",
+ "GPIO28",
+ "GPIO29",
+ "GPIO30",
+ "GPIO31",
+ "GPIO32",
+ "GPIO33",
+ "GPIO34",
+ "GPIO35",
+ "GPIO36",
+ "GPIO37",
+ "GPIO38",
+ "GPIO39",
+ "GPIO40",
+ "GPIO41",
+ "GPIO42",
+ "GPIO43",
+ "GPIO44",
+ "GPIO45",
+ "GPIO46",
+ "GPIO47",
+ /* Used by eMMC */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+
+ pinctrl-0 = <&gpioout &alt0>;
+};
+
+&hdmi {
+ hpd-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_gpio14>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/bcm2837-rpi-cm3.dtsi b/arch/arm/dts/bcm2837-rpi-cm3.dtsi
new file mode 100644
index 0000000..81399b2
--- /dev/null
+++ b/arch/arm/dts/bcm2837-rpi-cm3.dtsi
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2836-rpi.dtsi"
+
+/ {
+ memory@0 {
+ reg = <0 0x40000000>;
+ };
+
+ reg_3v3: fixed-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_1v8: fixed-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+};
+
+&firmware {
+ expgpio: gpio {
+ compatible = "raspberrypi,firmware-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "HDMI_HPD_N",
+ "EMMC_EN_N",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC";
+ status = "okay";
+ };
+};
+
+&sdhost {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhost_gpio48>;
+ bus-width = <4>;
+ vmmc-supply = <®_3v3>;
+ vqmmc-supply = <®_1v8>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/bcm2837.dtsi b/arch/arm/dts/bcm2837.dtsi
index bc1cca5..beb6c50 100644
--- a/arch/arm/dts/bcm2837.dtsi
+++ b/arch/arm/dts/bcm2837.dtsi
@@ -8,22 +8,28 @@
<0x40000000 0x40000000 0x00001000>;
dma-ranges = <0xc0000000 0x00000000 0x3f000000>;
- local_intc: local_intc {
+ local_intc: local_intc@40000000 {
compatible = "brcm,bcm2836-l1-intc";
reg = <0x40000000 0x100>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
interrupt-parent = <&local_intc>;
};
};
+ arm-pmu {
+ compatible = "arm,cortex-a53-pmu";
+ interrupt-parent = <&local_intc>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
timer {
compatible = "arm,armv7-timer";
interrupt-parent = <&local_intc>;
- interrupts = <0>, // PHYS_SECURE_PPI
- <1>, // PHYS_NONSECURE_PPI
- <3>, // VIRT_PPI
- <2>; // HYP_PPI
+ interrupts = <0 IRQ_TYPE_LEVEL_HIGH>, // PHYS_SECURE_PPI
+ <1 IRQ_TYPE_LEVEL_HIGH>, // PHYS_NONSECURE_PPI
+ <3 IRQ_TYPE_LEVEL_HIGH>, // VIRT_PPI
+ <2 IRQ_TYPE_LEVEL_HIGH>; // HYP_PPI
always-on;
};
@@ -73,7 +79,7 @@
compatible = "brcm,bcm2836-armctrl-ic";
reg = <0x7e00b200 0x200>;
interrupt-parent = <&local_intc>;
- interrupts = <8>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
};
&cpu_thermal {
diff --git a/arch/arm/dts/bcm283x-rpi-lan7515.dtsi b/arch/arm/dts/bcm283x-rpi-lan7515.dtsi
new file mode 100644
index 0000000..70bece6
--- /dev/null
+++ b/arch/arm/dts/bcm283x-rpi-lan7515.dtsi
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/net/microchip-lan78xx.h>
+
+/ {
+ aliases {
+ ethernet0 = ðernet;
+ };
+};
+
+&usb {
+ usb-port@1 {
+ compatible = "usb424,2514";
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb-port@1 {
+ compatible = "usb424,2514";
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet: ethernet@1 {
+ compatible = "usb424,7800";
+ reg = <1>;
+
+ mdio {
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+ eth_phy: ethernet-phy@1 {
+ reg = <1>;
+ microchip,led-modes = <
+ LAN78XX_LINK_1000_ACTIVITY
+ LAN78XX_LINK_10_100_ACTIVITY
+ >;
+ };
+ };
+ };
+ };
+ };
+};
diff --git a/arch/arm/dts/bcm283x-rpi-smsc9512.dtsi b/arch/arm/dts/bcm283x-rpi-smsc9512.dtsi
index 9a0599f..967e081 100644
--- a/arch/arm/dts/bcm283x-rpi-smsc9512.dtsi
+++ b/arch/arm/dts/bcm283x-rpi-smsc9512.dtsi
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
/ {
aliases {
ethernet0 = ðernet;
diff --git a/arch/arm/dts/bcm283x-rpi-usb-otg.dtsi b/arch/arm/dts/bcm283x-rpi-usb-otg.dtsi
new file mode 100644
index 0000000..e2fd961
--- /dev/null
+++ b/arch/arm/dts/bcm283x-rpi-usb-otg.dtsi
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0
+&usb {
+ dr_mode = "otg";
+ g-rx-fifo-size = <256>;
+ g-np-tx-fifo-size = <32>;
+ /*
+ * According to dwc2 the sum of all device EP
+ * fifo sizes shouldn't exceed 3776 bytes.
+ */
+ g-tx-fifo-size = <256 256 512 512 512 768 768>;
+};
diff --git a/arch/arm/dts/bcm283x.dtsi b/arch/arm/dts/bcm283x.dtsi
index e45ba58..9777644 100644
--- a/arch/arm/dts/bcm283x.dtsi
+++ b/arch/arm/dts/bcm283x.dtsi
@@ -2,6 +2,8 @@
#include <dt-bindings/clock/bcm2835.h>
#include <dt-bindings/clock/bcm2835-aux.h>
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/soc/bcm2835-pm.h>
/* firmware-provided startup stubs live here, where the secondary CPUs are
* spinning.
@@ -20,8 +22,13 @@
#address-cells = <1>;
#size-cells = <1>;
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ };
+
chosen {
- bootargs = "earlyprintk console=ttyAMA0";
+ stdout-path = "serial0:115200n8";
};
thermal-zones {
@@ -44,7 +51,7 @@
};
};
- soc: soc {
+ soc {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
@@ -60,6 +67,12 @@
clock-frequency = <1000000>;
};
+ txp@7e004000 {
+ compatible = "brcm,bcm2835-txp";
+ reg = <0x7e004000 0x20>;
+ interrupts = <1 11>;
+ };
+
dma: dma@7e007000 {
compatible = "brcm,bcm2835-dma";
reg = <0x7e007000 0xf00>;
@@ -108,9 +121,18 @@
#interrupt-cells = <2>;
};
- watchdog@7e100000 {
- compatible = "brcm,bcm2835-pm-wdt";
- reg = <0x7e100000 0x28>;
+ pm: watchdog@7e100000 {
+ compatible = "brcm,bcm2835-pm", "brcm,bcm2835-pm-wdt";
+ #power-domain-cells = <1>;
+ #reset-cells = <1>;
+ reg = <0x7e100000 0x114>,
+ <0x7e00a000 0x24>;
+ clocks = <&clocks BCM2835_CLOCK_V3D>,
+ <&clocks BCM2835_CLOCK_PERI_IMAGE>,
+ <&clocks BCM2835_CLOCK_H264>,
+ <&clocks BCM2835_CLOCK_ISP>;
+ clock-names = "v3d", "peri_image", "h264", "isp";
+ system-power-controller;
};
clocks: cprman@7e101000 {
@@ -130,6 +152,7 @@
rng@7e104000 {
compatible = "brcm,bcm2835-rng";
reg = <0x7e104000 0x10>;
+ interrupts = <2 29>;
};
mailbox: mailbox@7e00b880 {
@@ -217,6 +240,7 @@
gpclk2_gpio43: gpclk2_gpio43 {
brcm,pins = <43>;
brcm,function = <BCM2835_FSEL_ALT0>;
+ brcm,pull = <BCM2835_PUD_OFF>;
};
i2c0_gpio0: i2c0_gpio0 {
@@ -329,10 +353,12 @@
uart0_ctsrts_gpio30: uart0_ctsrts_gpio30 {
brcm,pins = <30 31>;
brcm,function = <BCM2835_FSEL_ALT3>;
+ brcm,pull = <BCM2835_PUD_UP BCM2835_PUD_OFF>;
};
uart0_gpio32: uart0_gpio32 {
brcm,pins = <32 33>;
brcm,function = <BCM2835_FSEL_ALT3>;
+ brcm,pull = <BCM2835_PUD_OFF BCM2835_PUD_UP>;
};
uart0_gpio36: uart0_gpio36 {
brcm,pins = <36 37>;
@@ -391,8 +417,8 @@
i2s: i2s@7e203000 {
compatible = "brcm,bcm2835-i2s";
- reg = <0x7e203000 0x20>,
- <0x7e101098 0x02>;
+ reg = <0x7e203000 0x24>;
+ clocks = <&clocks BCM2835_CLOCK_PCM>;
dmas = <&dma 2>,
<&dma 3>;
@@ -432,6 +458,17 @@
interrupts = <2 14>; /* pwa1 */
};
+ dpi: dpi@7e208000 {
+ compatible = "brcm,bcm2835-dpi";
+ reg = <0x7e208000 0x8c>;
+ clocks = <&clocks BCM2835_CLOCK_VPU>,
+ <&clocks BCM2835_CLOCK_DPI>;
+ clock-names = "core", "pixel";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
dsi0: dsi@7e209000 {
compatible = "brcm,bcm2835-dsi0";
reg = <0x7e209000 0x78>;
@@ -459,7 +496,7 @@
status = "disabled";
};
- aux: aux@0x7e215000 {
+ aux: aux@7e215000 {
compatible = "brcm,bcm2835-aux";
#clock-cells = <1>;
reg = <0x7e215000 0x8>;
@@ -602,6 +639,7 @@
compatible = "brcm,bcm2835-v3d";
reg = <0x7ec00000 0x1000>;
interrupts = <1 10>;
+ power-domains = <&pm BCM2835_POWER_DOMAIN_GRAFX_V3D>;
};
vc4: gpu {
@@ -634,7 +672,6 @@
usbphy: phy {
compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
};
};
-
-#include "bcm283x-uboot.dtsi"
diff --git a/arch/arm/mach-bcm283x/include/mach/mbox.h b/arch/arm/mach-bcm283x/include/mach/mbox.h
index 2776a39..e3a893e 100644
--- a/arch/arm/mach-bcm283x/include/mach/mbox.h
+++ b/arch/arm/mach-bcm283x/include/mach/mbox.h
@@ -348,7 +348,7 @@
};
#define BCM2835_MBOX_TAG_GET_PIXEL_ORDER 0x00040006
-#define BCM2835_MBOX_TAG_TEST_PIXEL_ORDER 0x00044005
+#define BCM2835_MBOX_TAG_TEST_PIXEL_ORDER 0x00044006
#define BCM2835_MBOX_TAG_SET_PIXEL_ORDER 0x00048006
#define BCM2835_MBOX_PIXEL_ORDER_BGR 0
diff --git a/arch/arm/mach-mediatek/Kconfig b/arch/arm/mach-mediatek/Kconfig
index b5e91d4..60aef15 100644
--- a/arch/arm/mach-mediatek/Kconfig
+++ b/arch/arm/mach-mediatek/Kconfig
@@ -12,7 +12,6 @@
config TARGET_MT7623
bool "MediaTek MT7623 SoC"
select CPU_V7A
- select ARCH_MISC_INIT
help
The MediaTek MT7623 is a ARM-based SoC with a quad-core Cortex-A7
including NEON and GPU, Mali-450 graphics, several DDR3 options,
@@ -25,7 +24,6 @@
bool "MediaTek MT7629 SoC"
select CPU_V7A
select SPL
- select ARCH_MISC_INIT
help
The MediaTek MT7629 is a ARM-based SoC with a dual-core Cortex-A7
including DDR3, crypto engine, 3x3 11n/ac Wi-Fi, Gigabit Ethernet,
@@ -34,7 +32,6 @@
config TARGET_MT8516
bool "MediaTek MT8516 SoC"
select ARM64
- select ARCH_MISC_INIT
help
The MediaTek MT8516 is a ARM64-based SoC with a quad-core Cortex-A35.
including UART, SPI, USB2.0 and OTG, SD and MMC cards, NAND, PWM,
diff --git a/arch/arm/mach-mediatek/cpu.c b/arch/arm/mach-mediatek/cpu.c
index b37e299..1923c9e 100644
--- a/arch/arm/mach-mediatek/cpu.c
+++ b/arch/arm/mach-mediatek/cpu.c
@@ -8,18 +8,6 @@
#include <wdt.h>
#include <dm/uclass-internal.h>
-int arch_misc_init(void)
-{
- struct udevice *wdt;
- int ret;
-
- ret = uclass_first_device_err(UCLASS_WDT, &wdt);
- if (!ret)
- wdt_stop(wdt);
-
- return 0;
-}
-
int arch_cpu_init(void)
{
icache_enable();
diff --git a/arch/arm/mach-rockchip/make_fit_atf.py b/arch/arm/mach-rockchip/make_fit_atf.py
index 45ec105..db0ae96 100755
--- a/arch/arm/mach-rockchip/make_fit_atf.py
+++ b/arch/arm/mach-rockchip/make_fit_atf.py
@@ -94,7 +94,7 @@
if segments != 0:
file.write(',')
for i in range(1, segments):
- file.write('"atf_%d"' % (i))
+ file.write('"atf_%d"' % (i + 1))
if i != (segments - 1):
file.write(',')
else:
diff --git a/arch/sandbox/dts/test.dts b/arch/sandbox/dts/test.dts
index 8b2d645..c328258 100644
--- a/arch/sandbox/dts/test.dts
+++ b/arch/sandbox/dts/test.dts
@@ -400,6 +400,18 @@
sandbox,silent; /* Don't emit sounds while testing */
};
+ nop-test_0 {
+ compatible = "sandbox,nop_sandbox1";
+ nop-test_1 {
+ compatible = "sandbox,nop_sandbox2";
+ bind = "True";
+ };
+ nop-test_2 {
+ compatible = "sandbox,nop_sandbox2";
+ bind = "False";
+ };
+ };
+
misc-test {
compatible = "sandbox,misc_sandbox";
};
diff --git a/common/board_r.c b/common/board_r.c
index 150e8cd..df24021 100644
--- a/common/board_r.c
+++ b/common/board_r.c
@@ -678,9 +678,6 @@
#ifdef CONFIG_DM
initr_dm,
#endif
-#if defined(CONFIG_WDT)
- initr_watchdog,
-#endif
#if defined(CONFIG_ARM) || defined(CONFIG_NDS32) || defined(CONFIG_RISCV) || \
defined(CONFIG_SANDBOX)
board_init, /* Setup chipselects */
@@ -700,6 +697,9 @@
stdio_init_tables,
initr_serial,
initr_announce,
+#if defined(CONFIG_WDT)
+ initr_watchdog,
+#endif
INIT_FUNC_WATCHDOG_RESET
#ifdef CONFIG_NEEDS_MANUAL_RELOC
initr_manual_reloc_cmdtable,
diff --git a/configs/rpi_3_b_plus_defconfig b/configs/rpi_3_b_plus_defconfig
new file mode 100644
index 0000000..2ae7b6d
--- /dev/null
+++ b/configs/rpi_3_b_plus_defconfig
@@ -0,0 +1,43 @@
+CONFIG_ARM=y
+CONFIG_ARCH_BCM283X=y
+CONFIG_SYS_TEXT_BASE=0x00080000
+CONFIG_TARGET_RPI_3=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_MISC_INIT_R=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_SYS_PROMPT="U-Boot> "
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_FS_UUID=y
+CONFIG_OF_EMBED=y
+CONFIG_DEFAULT_DEVICE_TREE="bcm2837-rpi-3-b-plus"
+CONFIG_ENV_FAT_INTERFACE="mmc"
+CONFIG_ENV_FAT_DEVICE_AND_PART="0:1"
+CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_DM_KEYBOARD=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_BCM2835=y
+CONFIG_PHYLIB=y
+CONFIG_DM_ETH=y
+CONFIG_PINCTRL=y
+# CONFIG_PINCTRL_GENERIC is not set
+# CONFIG_REQUIRE_SERIAL_CONSOLE is not set
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_DWC2=y
+CONFIG_USB_KEYBOARD=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_LAN78XX=y
+CONFIG_USB_ETHER_SMSC95XX=y
+CONFIG_DM_VIDEO=y
+CONFIG_SYS_WHITE_ON_BLACK=y
+CONFIG_CONSOLE_SCROLL_LINES=10
+CONFIG_PHYS_TO_BUS=y
+CONFIG_OF_LIBFDT_OVERLAY=y
diff --git a/drivers/core/uclass.c b/drivers/core/uclass.c
index fc3157d..dc9eb62 100644
--- a/drivers/core/uclass.c
+++ b/drivers/core/uclass.c
@@ -757,3 +757,8 @@
return 0;
}
#endif
+
+UCLASS_DRIVER(nop) = {
+ .id = UCLASS_NOP,
+ .name = "nop",
+};
diff --git a/drivers/usb/dwc3/dwc3-generic.c b/drivers/usb/dwc3/dwc3-generic.c
index 3e6c494..406bf0b 100644
--- a/drivers/usb/dwc3/dwc3-generic.c
+++ b/drivers/usb/dwc3/dwc3-generic.c
@@ -337,7 +337,7 @@
clk_release_bulk(&glue->clks);
- return dm_scan_fdt_dev(dev);
+ return 0;
}
static const struct udevice_id dwc3_glue_ids[] = {
@@ -350,7 +350,7 @@
U_BOOT_DRIVER(dwc3_generic_wrapper) = {
.name = "dwc3-generic-wrapper",
- .id = UCLASS_MISC,
+ .id = UCLASS_NOP,
.of_match = dwc3_glue_ids,
.bind = dwc3_glue_bind,
.probe = dwc3_glue_probe,
diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c
index 33abfea..e9e6ed5 100644
--- a/drivers/usb/host/ehci-mx6.c
+++ b/drivers/usb/host/ehci-mx6.c
@@ -503,6 +503,42 @@
return 0;
}
+static int ehci_usb_bind(struct udevice *dev)
+{
+ /*
+ * TODO:
+ * This driver is only partly converted to DT probing and still uses
+ * a tremendous amount of hard-coded addresses. To make things worse,
+ * the driver depends on specific sequential indexing of controllers,
+ * from which it derives offsets in the PHY and ANATOP register sets.
+ *
+ * Here we attempt to calculate these indexes from DT information as
+ * well as we can. The USB controllers on all existing iMX6/iMX7 SoCs
+ * are placed next to each other, at addresses incremented by 0x200.
+ * Thus, the index is derived from the multiple of 0x200 offset from
+ * the first controller address.
+ *
+ * However, to complete conversion of this driver to DT probing, the
+ * following has to be done:
+ * - DM clock framework support for iMX must be implemented
+ * - usb_power_config() has to be converted to clock framework
+ * -> Thus, the ad-hoc "index" variable goes away.
+ * - USB PHY handling has to be factored out into separate driver
+ * -> Thus, the ad-hoc "index" variable goes away from the PHY
+ * code, the PHY driver must parse it's address from DT. This
+ * USB driver must find the PHY driver via DT phandle.
+ * -> usb_power_config() shall be moved to PHY driver
+ * With these changes in place, the ad-hoc indexing goes away and
+ * the driver is fully converted to DT probing.
+ */
+ fdt_size_t size;
+ fdt_addr_t addr = devfdt_get_addr_size_index(dev, 0, &size);
+
+ dev->req_seq = (addr - USB_BASE_ADDR) / size;
+
+ return 0;
+}
+
static int ehci_usb_probe(struct udevice *dev)
{
struct usb_platdata *plat = dev_get_platdata(dev);
@@ -564,6 +600,7 @@
.id = UCLASS_USB,
.of_match = mx6_usb_ids,
.ofdata_to_platdata = ehci_usb_ofdata_to_platdata,
+ .bind = ehci_usb_bind,
.probe = ehci_usb_probe,
.remove = ehci_deregister,
.ops = &ehci_usb_ops,
diff --git a/drivers/video/pwm_backlight.c b/drivers/video/pwm_backlight.c
index a587977..ad20bf2 100644
--- a/drivers/video/pwm_backlight.c
+++ b/drivers/video/pwm_backlight.c
@@ -67,6 +67,9 @@
return log_ret(ret);
ret = pwm_set_invert(priv->pwm, priv->channel, priv->polarity);
+ if (ret == -ENOSYS && !priv->polarity)
+ ret = 0;
+
return log_ret(ret);
}
diff --git a/include/configs/rpi.h b/include/configs/rpi.h
index 9ce4176..f76c7d1 100644
--- a/include/configs/rpi.h
+++ b/include/configs/rpi.h
@@ -146,12 +146,38 @@
"fdt_addr_r=0x02600000\0" \
"ramdisk_addr_r=0x02700000\0"
+#if CONFIG_IS_ENABLED(CMD_MMC)
+ #define BOOT_TARGET_MMC(func) \
+ func(MMC, mmc, 0) \
+ func(MMC, mmc, 1)
+#else
+ #define BOOT_TARGET_MMC(func)
+#endif
+
+#if CONFIG_IS_ENABLED(CMD_USB)
+ #define BOOT_TARGET_USB(func) func(USB, usb, 0)
+#else
+ #define BOOT_TARGET_USB(func)
+#endif
+
+#if CONFIG_IS_ENABLED(CMD_PXE)
+ #define BOOT_TARGET_PXE(func) func(PXE, pxe, na)
+#else
+ #define BOOT_TARGET_PXE(func)
+#endif
+
+#if CONFIG_IS_ENABLED(CMD_DHCP)
+ #define BOOT_TARGET_DHCP(func) func(DHCP, dhcp, na)
+#else
+ #define BOOT_TARGET_DHCP(func)
+#endif
+
#define BOOT_TARGET_DEVICES(func) \
- func(MMC, mmc, 0) \
- func(MMC, mmc, 1) \
- func(USB, usb, 0) \
- func(PXE, pxe, na) \
- func(DHCP, dhcp, na)
+ BOOT_TARGET_MMC(func) \
+ BOOT_TARGET_USB(func) \
+ BOOT_TARGET_PXE(func) \
+ BOOT_TARGET_DHCP(func)
+
#include <config_distro_bootcmd.h>
#define CONFIG_EXTRA_ENV_SETTINGS \
diff --git a/include/configs/wandboard.h b/include/configs/wandboard.h
index 2e6262f..bdcd5e9 100644
--- a/include/configs/wandboard.h
+++ b/include/configs/wandboard.h
@@ -110,6 +110,7 @@
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 0) \
func(MMC, mmc, 1) \
+ func(MMC, mmc, 2) \
func(SATA, sata, 0) \
func(USB, usb, 0) \
func(PXE, pxe, na) \
diff --git a/include/dm/uclass-id.h b/include/dm/uclass-id.h
index 09e0ad5..4183928 100644
--- a/include/dm/uclass-id.h
+++ b/include/dm/uclass-id.h
@@ -62,6 +62,7 @@
UCLASS_MMC, /* SD / MMC card or chip */
UCLASS_MOD_EXP, /* RSA Mod Exp device */
UCLASS_MTD, /* Memory Technology Device (MTD) device */
+ UCLASS_NOP, /* No-op devices */
UCLASS_NORTHBRIDGE, /* Intel Northbridge / SDRAM controller */
UCLASS_NVME, /* NVM Express device */
UCLASS_PANEL, /* Display panel, such as an LCD */
diff --git a/include/dt-bindings/clock/bcm2835-aux.h b/include/dt-bindings/clock/bcm2835-aux.h
index d91156e..bb79de3 100644
--- a/include/dt-bindings/clock/bcm2835-aux.h
+++ b/include/dt-bindings/clock/bcm2835-aux.h
@@ -1,14 +1,6 @@
+/* SPDX-License-Identifier: GPL-2.0 */
/*
* Copyright (C) 2015 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
*/
#define BCM2835_AUX_CLOCK_UART 0
diff --git a/include/dt-bindings/clock/bcm2835.h b/include/dt-bindings/clock/bcm2835.h
index a0c812b..2cec01f 100644
--- a/include/dt-bindings/clock/bcm2835.h
+++ b/include/dt-bindings/clock/bcm2835.h
@@ -1,14 +1,6 @@
+/* SPDX-License-Identifier: GPL-2.0 */
/*
* Copyright (C) 2015 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
*/
#define BCM2835_PLLA 0
diff --git a/include/dt-bindings/net/microchip-lan78xx.h b/include/dt-bindings/net/microchip-lan78xx.h
new file mode 100644
index 0000000..0742ff0
--- /dev/null
+++ b/include/dt-bindings/net/microchip-lan78xx.h
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _DT_BINDINGS_MICROCHIP_LAN78XX_H
+#define _DT_BINDINGS_MICROCHIP_LAN78XX_H
+
+/* LED modes for LAN7800/LAN7850 embedded PHY */
+
+#define LAN78XX_LINK_ACTIVITY 0
+#define LAN78XX_LINK_1000_ACTIVITY 1
+#define LAN78XX_LINK_100_ACTIVITY 2
+#define LAN78XX_LINK_10_ACTIVITY 3
+#define LAN78XX_LINK_100_1000_ACTIVITY 4
+#define LAN78XX_LINK_10_1000_ACTIVITY 5
+#define LAN78XX_LINK_10_100_ACTIVITY 6
+#define LAN78XX_DUPLEX_COLLISION 8
+#define LAN78XX_COLLISION 9
+#define LAN78XX_ACTIVITY 10
+#define LAN78XX_AUTONEG_FAULT 12
+#define LAN78XX_FORCE_LED_OFF 14
+#define LAN78XX_FORCE_LED_ON 15
+
+#endif
diff --git a/include/dt-bindings/pinctrl/bcm2835.h b/include/dt-bindings/pinctrl/bcm2835.h
index e4e4fdf..b5b2654 100644
--- a/include/dt-bindings/pinctrl/bcm2835.h
+++ b/include/dt-bindings/pinctrl/bcm2835.h
@@ -1,14 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0 */
/*
* Header providing constants for bcm2835 pinctrl bindings.
*
* Copyright (C) 2015 Stefan Wahren <stefan.wahren@i2se.com>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
*/
#ifndef __DT_BINDINGS_PINCTRL_BCM2835_H__
diff --git a/include/dt-bindings/soc/bcm2835-pm.h b/include/dt-bindings/soc/bcm2835-pm.h
new file mode 100644
index 0000000..153d75b
--- /dev/null
+++ b/include/dt-bindings/soc/bcm2835-pm.h
@@ -0,0 +1,28 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
+
+#ifndef _DT_BINDINGS_ARM_BCM2835_PM_H
+#define _DT_BINDINGS_ARM_BCM2835_PM_H
+
+#define BCM2835_POWER_DOMAIN_GRAFX 0
+#define BCM2835_POWER_DOMAIN_GRAFX_V3D 1
+#define BCM2835_POWER_DOMAIN_IMAGE 2
+#define BCM2835_POWER_DOMAIN_IMAGE_PERI 3
+#define BCM2835_POWER_DOMAIN_IMAGE_ISP 4
+#define BCM2835_POWER_DOMAIN_IMAGE_H264 5
+#define BCM2835_POWER_DOMAIN_USB 6
+#define BCM2835_POWER_DOMAIN_DSI0 7
+#define BCM2835_POWER_DOMAIN_DSI1 8
+#define BCM2835_POWER_DOMAIN_CAM0 9
+#define BCM2835_POWER_DOMAIN_CAM1 10
+#define BCM2835_POWER_DOMAIN_CCP2TX 11
+#define BCM2835_POWER_DOMAIN_HDMI 12
+
+#define BCM2835_POWER_DOMAIN_COUNT 13
+
+#define BCM2835_RESET_V3D 0
+#define BCM2835_RESET_ISP 1
+#define BCM2835_RESET_H264 2
+
+#define BCM2835_RESET_COUNT 3
+
+#endif /* _DT_BINDINGS_ARM_BCM2835_PM_H */
diff --git a/test/dm/Makefile b/test/dm/Makefile
index 49857c5..aeb3aa0 100644
--- a/test/dm/Makefile
+++ b/test/dm/Makefile
@@ -3,6 +3,7 @@
# Copyright (c) 2013 Google, Inc
obj-$(CONFIG_UT_DM) += bus.o
+obj-$(CONFIG_UT_DM) += nop.o
obj-$(CONFIG_UT_DM) += test-driver.o
obj-$(CONFIG_UT_DM) += test-fdt.o
obj-$(CONFIG_UT_DM) += test-main.o
diff --git a/test/dm/nop.c b/test/dm/nop.c
new file mode 100644
index 0000000..2df29f3
--- /dev/null
+++ b/test/dm/nop.c
@@ -0,0 +1,73 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Test for the NOP uclass
+ *
+ * (C) Copyright 2019 - Texas Instruments Incorporated - http://www.ti.com/
+ * Jean-Jacques Hiblot <jjhiblot@ti.com>
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <dm/ofnode.h>
+#include <dm/lists.h>
+#include <dm/device.h>
+#include <dm/test.h>
+#include <misc.h>
+#include <test/ut.h>
+
+static int noptest_bind(struct udevice *parent)
+{
+ ofnode ofnode = dev_read_first_subnode(parent);
+
+ while (ofnode_valid(ofnode)) {
+ struct udevice *dev;
+ const char *bind_flag = ofnode_read_string(ofnode, "bind");
+
+ if (bind_flag && (strcmp(bind_flag, "True") == 0))
+ lists_bind_fdt(parent, ofnode, &dev, false);
+ ofnode = dev_read_next_subnode(ofnode);
+ }
+
+ return 0;
+}
+
+static const struct udevice_id noptest1_ids[] = {
+ {
+ .compatible = "sandbox,nop_sandbox1",
+ },
+ { }
+};
+
+U_BOOT_DRIVER(noptest_drv1) = {
+ .name = "noptest1_drv",
+ .of_match = noptest1_ids,
+ .id = UCLASS_NOP,
+ .bind = noptest_bind,
+};
+
+static const struct udevice_id noptest2_ids[] = {
+ {
+ .compatible = "sandbox,nop_sandbox2",
+ },
+ { }
+};
+
+U_BOOT_DRIVER(noptest_drv2) = {
+ .name = "noptest2_drv",
+ .of_match = noptest2_ids,
+ .id = UCLASS_NOP,
+};
+
+static int dm_test_nop(struct unit_test_state *uts)
+{
+ struct udevice *dev;
+
+ ut_assertok(uclass_get_device_by_name(UCLASS_NOP, "nop-test_0", &dev));
+ ut_assertok(uclass_get_device_by_name(UCLASS_NOP, "nop-test_1", &dev));
+ ut_asserteq(-ENODEV,
+ uclass_get_device_by_name(UCLASS_NOP, "nop-test_2", &dev));
+
+ return 0;
+}
+
+DM_TEST(dm_test_nop, DM_TESTF_FLAT_TREE | DM_TESTF_SCAN_FDT);