mx6sabreauto: Convert to DM_PMIC
The usage of DM_PMIC is preferred, so convert to it.
This also brings the benefit of causing a significant amount
of code removal.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
diff --git a/board/freescale/mx6sabreauto/mx6sabreauto.c b/board/freescale/mx6sabreauto/mx6sabreauto.c
index 9155dcf..039deb5 100644
--- a/board/freescale/mx6sabreauto/mx6sabreauto.c
+++ b/board/freescale/mx6sabreauto/mx6sabreauto.c
@@ -19,14 +19,12 @@
#include <linux/errno.h>
#include <asm/gpio.h>
#include <asm/mach-imx/iomux-v3.h>
-#include <asm/mach-imx/mxc_i2c.h>
#include <asm/mach-imx/boot_mode.h>
#include <asm/mach-imx/spi.h>
#include <mmc.h>
#include <fsl_esdhc_imx.h>
#include <miiphy.h>
#include <asm/arch/sys_proto.h>
-#include <i2c.h>
#include <input.h>
#include <asm/arch/mxc_hdmi.h>
#include <asm/mach-imx/video.h>
@@ -49,23 +47,15 @@
#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
-#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
- PAD_CTL_ODE | PAD_CTL_SRE_FAST)
-
#define GPMI_PAD_CTRL0 (PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP)
#define GPMI_PAD_CTRL1 (PAD_CTL_DSE_40ohm | PAD_CTL_SPEED_MED | \
PAD_CTL_SRE_FAST)
#define GPMI_PAD_CTRL2 (GPMI_PAD_CTRL0 | GPMI_PAD_CTRL1)
-#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
-
#define WEIM_NOR_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
-#define I2C_PMIC 1
-
int dram_init(void)
{
gd->ram_size = imx_ddr_size();
@@ -78,70 +68,6 @@
IOMUX_PADS(PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
};
-
-/* I2C2 PMIC, iPod, Tuner, Codec, Touch, HDMI EDID, MIPI CSI2 card */
-static struct i2c_pads_info mx6q_i2c_pad_info1 = {
- .scl = {
- .i2c_mode = MX6Q_PAD_EIM_EB2__I2C2_SCL | PC,
- .gpio_mode = MX6Q_PAD_EIM_EB2__GPIO2_IO30 | PC,
- .gp = IMX_GPIO_NR(2, 30)
- },
- .sda = {
- .i2c_mode = MX6Q_PAD_KEY_ROW3__I2C2_SDA | PC,
- .gpio_mode = MX6Q_PAD_KEY_ROW3__GPIO4_IO13 | PC,
- .gp = IMX_GPIO_NR(4, 13)
- }
-};
-
-static struct i2c_pads_info mx6dl_i2c_pad_info1 = {
- .scl = {
- .i2c_mode = MX6DL_PAD_EIM_EB2__I2C2_SCL | PC,
- .gpio_mode = MX6DL_PAD_EIM_EB2__GPIO2_IO30 | PC,
- .gp = IMX_GPIO_NR(2, 30)
- },
- .sda = {
- .i2c_mode = MX6DL_PAD_KEY_ROW3__I2C2_SDA | PC,
- .gpio_mode = MX6DL_PAD_KEY_ROW3__GPIO4_IO13 | PC,
- .gp = IMX_GPIO_NR(4, 13)
- }
-};
-
-#ifndef CONFIG_SYS_FLASH_CFI
-/*
- * I2C3 MLB, Port Expanders (A, B, C), Video ADC, Light Sensor,
- * Compass Sensor, Accelerometer, Res Touch
- */
-static struct i2c_pads_info mx6q_i2c_pad_info2 = {
- .scl = {
- .i2c_mode = MX6Q_PAD_GPIO_3__I2C3_SCL | PC,
- .gpio_mode = MX6Q_PAD_GPIO_3__GPIO1_IO03 | PC,
- .gp = IMX_GPIO_NR(1, 3)
- },
- .sda = {
- .i2c_mode = MX6Q_PAD_EIM_D18__I2C3_SDA | PC,
- .gpio_mode = MX6Q_PAD_EIM_D18__GPIO3_IO18 | PC,
- .gp = IMX_GPIO_NR(3, 18)
- }
-};
-
-static struct i2c_pads_info mx6dl_i2c_pad_info2 = {
- .scl = {
- .i2c_mode = MX6DL_PAD_GPIO_3__I2C3_SCL | PC,
- .gpio_mode = MX6DL_PAD_GPIO_3__GPIO1_IO03 | PC,
- .gp = IMX_GPIO_NR(1, 3)
- },
- .sda = {
- .i2c_mode = MX6DL_PAD_EIM_D18__I2C3_SDA | PC,
- .gpio_mode = MX6DL_PAD_EIM_D18__GPIO3_IO18 | PC,
- .gp = IMX_GPIO_NR(3, 18)
- }
-};
-#endif
-
-static iomux_v3_cfg_t const i2c3_pads[] = {
- IOMUX_PADS(PAD_EIM_A24__GPIO5_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL)),
-};
-
static iomux_v3_cfg_t const port_exp[] = {
IOMUX_PADS(PAD_SD2_DAT0__GPIO1_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
@@ -516,21 +442,10 @@
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
- /* I2C 2 and 3 setup - I2C 3 hw mux with EIM */
- if (is_mx6dq() || is_mx6dqp())
- setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c_pad_info1);
- else
- setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info1);
/* I2C 3 Steer */
gpio_request(IMX_GPIO_NR(5, 4), "steer logic");
gpio_direction_output(IMX_GPIO_NR(5, 4), 1);
- SETUP_IOMUX_PADS(i2c3_pads);
-#ifndef CONFIG_SYS_FLASH_CFI
- if (is_mx6dq() || is_mx6dqp())
- setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c_pad_info2);
- else
- setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info2);
-#endif
+
gpio_request(IMX_GPIO_NR(1, 15), "expander en");
gpio_direction_output(IMX_GPIO_NR(1, 15), 1);
SETUP_IOMUX_PADS(port_exp);
@@ -554,22 +469,27 @@
int power_init_board(void)
{
- struct pmic *p;
+ struct udevice *dev;
unsigned int value;
+ int ret;
+
+ ret = pmic_get("pfuze100@8", &dev);
+ if (ret == -ENODEV)
+ return 0;
- p = pfuze_common_init(I2C_PMIC);
- if (!p)
- return -ENODEV;
+ if (ret != 0)
+ return ret;
+
if (is_mx6dqp()) {
/* set SW2 staby volatage 0.975V*/
- pmic_reg_read(p, PFUZE100_SW2STBY, &value);
+ value = pmic_reg_read(dev, PFUZE100_SW2STBY);
value &= ~0x3f;
value |= 0x17;
- pmic_reg_write(p, PFUZE100_SW2STBY, value);
+ pmic_reg_write(dev, PFUZE100_SW2STBY, value);
}
- return pfuze_mode_init(p, APS_PFM);
+ return pfuze_mode_init(dev, APS_PFM);
}
#ifdef CONFIG_CMD_BMODE
@@ -979,7 +899,6 @@
ccgr_init();
gpr_init();
- /* iomux and setup of i2c */
board_early_init_f();
/* setup GP timer */