cmd: mvebu/bubt: Add support for selecting eMMC HW partition
Support for burning into the correct eMMC HW boot partition was broken and
removed in commit 96be2f072768 ("mvebu: bubt: Drop dead code"). Reimplement
this functionality and bring it back again.
Fixes: 96be2f072768 ("mvebu: bubt: Drop dead code")
Signed-off-by: Pali Rohár <pali@kernel.org>
diff --git a/cmd/mvebu/bubt.c b/cmd/mvebu/bubt.c
index 2bcdf14..4bad9a6 100644
--- a/cmd/mvebu/bubt.c
+++ b/cmd/mvebu/bubt.c
@@ -189,6 +189,11 @@
#ifdef CONFIG_BLK
struct blk_desc *blk_desc;
#endif
+#ifdef CONFIG_SUPPORT_EMMC_BOOT
+ u8 part;
+ u8 orig_part;
+#endif
+
mmc = find_mmc_device(mmc_dev_num);
if (!mmc) {
printf("No SD/MMC/eMMC card found\n");
@@ -201,6 +206,38 @@
mmc_dev_num);
return err;
}
+
+#ifdef CONFIG_BLK
+ blk_desc = mmc_get_blk_desc(mmc);
+ if (!blk_desc) {
+ printf("Error - failed to obtain block descriptor\n");
+ return -ENODEV;
+ }
+#endif
+
+#ifdef CONFIG_SUPPORT_EMMC_BOOT
+#ifdef CONFIG_BLK
+ orig_part = blk_desc->hwpart;
+#else
+ orig_part = mmc->block_dev.hwpart;
+#endif
+
+ part = (mmc->part_config >> 3) & PART_ACCESS_MASK;
+
+ if (part == 7)
+ part = 0;
+
+#ifdef CONFIG_BLK
+ err = blk_dselect_hwpart(blk_desc, part);
+#else
+ err = mmc_switch_part(mmc, part);
+#endif
+
+ if (err) {
+ printf("Error - MMC partition switch failed\n");
+ return err;
+ }
+#endif
/* SD reserves LBA-0 for MBR and boots from LBA-1,
* MMC/eMMC boots from LBA-0
@@ -211,11 +248,6 @@
if (image_size % mmc->write_bl_len)
blk_count += 1;
- blk_desc = mmc_get_blk_desc(mmc);
- if (!blk_desc) {
- printf("Error - failed to obtain block descriptor\n");
- return -ENODEV;
- }
blk_written = blk_dwrite(blk_desc, start_lba, blk_count,
(void *)get_load_addr());
#else
@@ -227,6 +259,17 @@
start_lba, blk_count,
(void *)get_load_addr());
#endif /* CONFIG_BLK */
+
+#ifdef CONFIG_SUPPORT_EMMC_BOOT
+#ifdef CONFIG_BLK
+ err = blk_dselect_hwpart(blk_desc, orig_part);
+#else
+ err = mmc_switch_part(mmc, orig_part);
+#endif
+ if (err)
+ printf("Error - MMC failed to switch back to original partition\n");
+#endif
+
if (blk_written != blk_count) {
printf("Error - written %#lx blocks\n", blk_written);
return -ENOSPC;
diff --git a/doc/mvebu/cmd/bubt.txt b/doc/mvebu/cmd/bubt.txt
index 6051243..1fe1f07 100644
--- a/doc/mvebu/cmd/bubt.txt
+++ b/doc/mvebu/cmd/bubt.txt
@@ -14,8 +14,7 @@
Notes:
- For the TFTP interface set serverip and ipaddr.
-- To burn image to SD/eMMC device, the target is defined
- by parameters CONFIG_SYS_MMC_ENV_DEV and CONFIG_SYS_MMC_ENV_PART.
+- To burn image to SD/eMMC device, the target is defined by HW partition.
Bubt command details (burn image step by-step)
----------------------------------------------
@@ -40,10 +39,20 @@
Number 0 is used for user data partition and should not be utilized for storing
boot images and U-Boot environment in RAW mode since it will break file system
structures usually located here.
- The default boot partition is BOOT0. It is selected by the following parameter:
- CONFIG_SYS_MMC_ENV_PART=1
- Valid values for this parameter are 1 for BOOT0 and 2 for BOOT1.
- Please never use partition number 0 here!
+
+ Currently configured boot partition can be printed by command:
+ # mmc partconf 0
+ (search for BOOT_PARTITION_ACCESS output, number 7 is user data)
+
+ Change it to BOOT0:
+ # mmc partconf 0 0 1 1
+
+ Change it to BOOT1:
+ # mmc partconf 0 0 2 2
+
+ Change it to user data:
+ # mmc partconf 0 0 7 0
+
- The partition number is ignored if the target device is SD card.
- The boot image offset starts at block 0 for eMMC and block 1 for SD devices.
The block 0 on SD devices is left for MBR storage.