blob: 8fbbe30bd224d490041f3b5678fbaa1fe5219da7 [file] [log] [blame]
/*
* (C) Copyright 2001
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/***********************************************************
* High Level Configuration Options
* (easy to change)
***********************************************************/
#define CONFIG_405GP 1 /* This is a PPC405 CPU */
#define CONFIG_4xx 1 /* ...member of PPC4xx family */
#define CONFIG_PIP405 1 /* ...on a PIP405 board */
/***********************************************************
* Clock
***********************************************************/
#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
/***********************************************************
* Command definitions
***********************************************************/
#define CONFIG_COMMANDS \
(CONFIG_CMD_DFL | \
CFG_CMD_IDE | \
CFG_CMD_DHCP | \
CFG_CMD_PCI | \
CFG_CMD_CACHE | \
CFG_CMD_IRQ | \
CFG_CMD_EEPROM | \
CFG_CMD_I2C | \
CFG_CMD_REGINFO | \
CFG_CMD_FDC | \
CFG_CMD_SCSI | \
CFG_CMD_DATE | \
CFG_CMD_ELF | \
CFG_CMD_USB | \
CFG_CMD_MII | \
CFG_CMD_SDRAM | \
CFG_CMD_DOC | \
CFG_CMD_SAVES | \
CFG_CMD_BSP )
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
#define CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
/**************************************************************
* I2C Stuff:
* the PIP405 is equiped with an Atmel 24C128/256 EEPROM at address
* 0x53.
* Caution: on the same bus is the SPD (Serial Presens Detect
* EEPROM of the SDRAM
* The Atmel EEPROM uses 16Bit addressing.
***************************************************************/
#define CONFIG_HARD_I2C /* I2c with hardware support */
#define CFG_I2C_SPEED 50000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_EEPROM_ADDR 0x53
#define CFG_I2C_EEPROM_ADDR_LEN 2
#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
#define CFG_ENV_SIZE 0x800 /* 2 kBytes may be used for env vars */
#undef CFG_I2C_EEPROM_ADDR_OVERFLOW
#define CFG_EEPROM_PAGE_WRITE_BITS 6 /* The Atmel 24C128/256 has */
/* 64 byte page write mode using*/
/* last 6 bits of the address */
#define CFG_EEPROM_PAGE_WRITE_ENABLE /* enable Page write */
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
/***************************************************************
* Definitions for Serial Presence Detect EEPROM address
* (to get SDRAM settings)
***************************************************************/
#define SPD_EEPROM_ADDRESS 0x50
#define CONFIG_BOARD_PRE_INIT
/**************************************************************
* Environment definitions
**************************************************************/
#define CONFIG_BAUDRATE 9600 /* STD Baudrate */
#define CONFIG_BOOTDELAY 5
/* autoboot (do NOT change this set environment variable "bootdelay" to -1 instead) */
#define CONFIG_BOOT_RETRY_TIME -10 /* feature is avaiable but not enabled */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check console even if bootdelay = 0 */
#define CONFIG_BOOTCOMMAND "diskboot 400000 0:1; bootm" /* autoboot command */
#define CONFIG_BOOTARGS "console=ttyS0,9600 root=/dev/hda5" /* boot arguments */
#define CONFIG_IPADDR 10.0.0.100
#define CONFIG_SERVERIP 10.0.0.1
#define CONFIG_PREBOOT
/***************************************************************
* defines if the console is stored in the environment
***************************************************************/
#define CFG_CONSOLE_IS_IN_ENV /* stdin, stdout and stderr are in evironment */
/***************************************************************
* defines if an overwrite_console function exists
*************************************************************/
#define CFG_CONSOLE_OVERWRITE_ROUTINE
#define CFG_CONSOLE_INFO_QUIET
/***************************************************************
* defines if the overwrite_console should be stored in the
* environment
**************************************************************/
#undef CFG_CONSOLE_ENV_OVERWRITE
/**************************************************************
* loads config
*************************************************************/
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/***********************************************************
* Miscellaneous configurable options
**********************************************************/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_MEMTEST_START 0x0100000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 1 ... 12 MB in DRAM */
#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
#define CFG_BASE_BAUD 691200
/* The following table includes the supported baudrates */
#define CFG_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
#define CFG_LOAD_ADDR 0x400000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
*/
#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
#define PCI_HOST_FORCE 1 /* configure as pci host */
#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_HOST PCI_HOST_FORCE /* configure as pci-host */
#define CONFIG_PCI_PNP /* pci plug-and-play */
/* resource configuration */
#define CFG_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */
#define CFG_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */
#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
#define CFG_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
#define CFG_PCI_PTM2LA 0x00000000 /* disabled */
#define CFG_PCI_PTM2MS 0x00000000 /* disabled */
#define CFG_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0xFFF80000
#define CFG_MONITOR_BASE CFG_FLASH_BASE
#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CFG_DCACHE_SIZE 8192 /* For IBM 405 CPUs */
#define CFG_CACHELINE_SIZE 32 /* ... */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*
* Init Memory Controller:
*/
#define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */
#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */
/* Configuration Port location */
#define CONFIG_PORT_ADDR 0xF4000000
#define MULTI_PURPOSE_SOCKET_ADDR 0xF8000000
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in On Chip SRAM)
*/
#define CFG_TEMP_STACK_OCM 1
#define CFG_OCM_DATA_ADDR 0xF0000000
#define CFG_OCM_DATA_SIZE 0x1000
#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of On Chip SRAM */
#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of On Chip SRAM */
#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
/***********************************************************************
* External peripheral base address
***********************************************************************/
#define CFG_ISA_IO_BASE_ADDRESS 0xE8000000
/***********************************************************************
* Last Stage Init
***********************************************************************/
#define CONFIG_LAST_STAGE_INIT
/************************************************************
* Ethernet Stuff
***********************************************************/
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1 /* PHY address */
#define CONFIG_CS8952_PHY 1 /* its a CS8952 PHY */
/************************************************************
* RTC
***********************************************************/
#define CONFIG_RTC_MC146818
#undef CONFIG_WATCHDOG /* watchdog disabled */
/************************************************************
* IDE/ATA stuff
************************************************************/
#define CFG_IDE_MAXBUS 2 /* max. 2 IDE busses */
#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
#define CFG_ATA_BASE_ADDR CFG_ISA_IO_BASE_ADDRESS /* base address */
#define CFG_ATA_IDE0_OFFSET 0x01F0 /* ide0 offste */
#define CFG_ATA_IDE1_OFFSET 0x0170 /* ide1 offset */
#define CFG_ATA_DATA_OFFSET 0 /* data reg offset */
#define CFG_ATA_REG_OFFSET 0 /* reg offset */
#define CFG_ATA_ALT_OFFSET 0x200 /* alternate register offset */
#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
#undef CONFIG_IDE_LED /* no led for ide supported */
#define CONFIG_IDE_RESET /* reset for ide supported... */
#define CONFIG_IDE_RESET_ROUTINE /* with a special reset function */
/************************************************************
* ATAPI support (experimental)
************************************************************/
#define CONFIG_ATAPI /* enable ATAPI Support */
/************************************************************
* SCSI support (experimental) only SYM53C8xx supported
************************************************************/
#define CONFIG_SCSI_SYM53C8XX
#define CFG_SCSI_MAX_LUN 8 /* number of supported LUNs */
#define CFG_SCSI_MAX_SCSI_ID 7 /* maximum SCSI ID (0..6) */
#define CFG_SCSI_MAX_DEVICE CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN /* maximum Target devices */
#define CFG_SCSI_SPIN_UP_TIME 2
/************************************************************
* Disk-On-Chip configuration
************************************************************/
#define CFG_MAX_DOC_DEVICE 1 /* Max number of DOC devices */
#define CFG_DOC_SHORT_TIMEOUT
#define CFG_DOC_SUPPORT_2000
#define CFG_DOC_SUPPORT_MILLENNIUM
/************************************************************
* DISK Partition support
************************************************************/
#define CONFIG_DOS_PARTITION
#define CONFIG_MAC_PARTITION
#define CONFIG_ISO_PARTITION /* Experimental */
/************************************************************
* Keyboard support
************************************************************/
#define CONFIG_ISA_KEYBOARD
/************************************************************
* Video support
************************************************************/
#define CONFIG_VIDEO /*To enable video controller support */
#define CONFIG_VIDEO_CT69000
#define CONFIG_CFB_CONSOLE
#define CONFIG_VIDEO_LOGO
#define CONFIG_CONSOLE_EXTRA_INFO
#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_VIDEO_SW_CURSOR
#define CONFIG_VIDEO_ONBOARD /* Video controller is on-board */
/************************************************************
* USB support
************************************************************/
#define CONFIG_USB_UHCI
#define CONFIG_USB_KEYBOARD
#define CONFIG_USB_STORAGE
/* Enable needed helper functions */
#define CFG_DEVICE_DEREGISTER /* needs device_deregister */
/************************************************************
* Debug support
************************************************************/
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/************************************************************
* Ident
************************************************************/
#define VERSION_TAG "released"
#define CONFIG_ISO_STRING "MEV-10066-001"
#define CONFIG_IDENT_STRING "\n(c) 2002 by MPL AG Switzerland, " CONFIG_ISO_STRING " " VERSION_TAG
#endif /* __CONFIG_H */