// SPDX-License-Identifier: GPL-2.0+
/*
 * (C) Copyright 2007-2008
 * Stelian Pop <stelian@popies.net>
 * Lead Tech Design <www.leadtechdesign.com>
 */

#include <common.h>
#include <debug_uart.h>
#include <init.h>
#include <net.h>
#include <vsprintf.h>
#include <asm/global_data.h>
#include <asm/io.h>
#include <asm/arch/clk.h>
#include <asm/arch/at91sam9g45_matrix.h>
#include <asm/arch/at91sam9_smc.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/gpio.h>
#include <asm/arch/clk.h>
#include <lcd.h>
#include <linux/mtd/rawnand.h>
#include <atmel_lcdc.h>
#include <asm/mach-types.h>

DECLARE_GLOBAL_DATA_PTR;

/* ------------------------------------------------------------------------- */
/*
 * Miscelaneous platform dependent initialisations
 */

#ifdef CONFIG_CMD_NAND
void at91sam9m10g45ek_nand_hw_init(void)
{
	struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
	struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
	unsigned long csa;

	/* Enable CS3 */
	csa = readl(&matrix->ebicsa);
	csa |= AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA;
	writel(csa, &matrix->ebicsa);

	/* Configure SMC CS3 for NAND/SmartMedia */
	writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
	       AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
	       &smc->cs[3].setup);
	writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(3) |
	       AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(2),
	       &smc->cs[3].pulse);
	writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(4),
	       &smc->cs[3].cycle);
	writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
	       AT91_SMC_MODE_EXNW_DISABLE |
#ifdef CONFIG_SYS_NAND_DBW_16
	       AT91_SMC_MODE_DBW_16 |
#else /* CONFIG_SYS_NAND_DBW_8 */
	       AT91_SMC_MODE_DBW_8 |
#endif
	       AT91_SMC_MODE_TDF_CYCLE(3),
	       &smc->cs[3].mode);

	at91_periph_clk_enable(ATMEL_ID_PIOC);

	/* Configure RDY/BSY */
	at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);

	/* Enable NandFlash */
	at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
}
#endif

#if defined(CONFIG_SPL_BUILD)
#include <spl.h>
#include <nand.h>

void at91_spl_board_init(void)
{
	/*
	 * On the at91sam9m10g45ek board, the chip wm9711 stays in the
	 * test mode, so it needs do some action to exit test mode.
	 */
	at91_periph_clk_enable(ATMEL_ID_PIODE);
	at91_set_gpio_output(AT91_PIN_PD7, 0);
	at91_set_gpio_output(AT91_PIN_PD8, 0);
	at91_set_pio_pullup(AT91_PIO_PORTD, 7, 1);
	at91_set_pio_pullup(AT91_PIO_PORTD, 8, 1);

#ifdef CONFIG_SD_BOOT
	at91_mci_hw_init();
#elif CONFIG_NAND_BOOT
	at91sam9m10g45ek_nand_hw_init();
#endif
}

#include <asm/arch/atmel_mpddrc.h>
static void ddr2_conf(struct atmel_mpddrc_config *ddr2)
{
	ddr2->md = (ATMEL_MPDDRC_MD_DBW_16_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM);

	ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
		    ATMEL_MPDDRC_CR_NR_ROW_14 |
		    ATMEL_MPDDRC_CR_DQMS_SHARED |
		    ATMEL_MPDDRC_CR_CAS_DDR_CAS3);

	ddr2->rtr = 0x24b;

	ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |/* 6*7.5 = 45 ns */
		      2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |/* 2*7.5 = 15 ns */
		      2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET | /* 2*7.5 = 15 ns */
		      8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET | /* 8*7.5 = 60 ns */
		      2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET | /* 2*7.5 = 15 ns */
		      1 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET | /* 1*7.5= 7.5 ns*/
		      1 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET | /* 1 clk cycle */
		      2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET); /* 2 clk cycles */

	ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET | /* 2*7.5 = 15 ns */
		      200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET |
		      16 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET |
		      14 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET);

	ddr2->tpr2 = (1 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET |
		      0 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET |
		      7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET |
		      2 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET);
}

void mem_init(void)
{
	struct atmel_mpddrc_config ddr2;

	ddr2_conf(&ddr2);

	at91_system_clk_enable(AT91_PMC_DDR);

	/* DDRAM2 Controller initialize */
	ddr2_init(ATMEL_BASE_DDRSDRC0, ATMEL_BASE_CS6, &ddr2);
}
#endif

#ifdef CONFIG_CMD_USB
static void at91sam9m10g45ek_usb_hw_init(void)
{
	at91_periph_clk_enable(ATMEL_ID_PIODE);

	at91_set_gpio_output(AT91_PIN_PD1, 0);
	at91_set_gpio_output(AT91_PIN_PD3, 0);
}
#endif

#ifdef CONFIG_LCD

vidinfo_t panel_info = {
	.vl_col =		480,
	.vl_row =		272,
	.vl_clk =		9000000,
	.vl_sync =		ATMEL_LCDC_INVLINE_NORMAL |
				ATMEL_LCDC_INVFRAME_NORMAL,
	.vl_bpix =		3,
	.vl_tft =		1,
	.vl_hsync_len =		45,
	.vl_left_margin =	1,
	.vl_right_margin =	1,
	.vl_vsync_len =		1,
	.vl_upper_margin =	40,
	.vl_lower_margin =	1,
	.mmio =			ATMEL_BASE_LCDC,
};


void lcd_enable(void)
{
	at91_set_A_periph(AT91_PIN_PE6, 1);	/* power up */
}

void lcd_disable(void)
{
	at91_set_A_periph(AT91_PIN_PE6, 0);	/* power down */
}

static void at91sam9m10g45ek_lcd_hw_init(void)
{
	at91_set_A_periph(AT91_PIN_PE0, 0);	/* LCDDPWR */
	at91_set_A_periph(AT91_PIN_PE2, 0);	/* LCDCC */
	at91_set_A_periph(AT91_PIN_PE3, 0);	/* LCDVSYNC */
	at91_set_A_periph(AT91_PIN_PE4, 0);	/* LCDHSYNC */
	at91_set_A_periph(AT91_PIN_PE5, 0);	/* LCDDOTCK */

	at91_set_A_periph(AT91_PIN_PE7, 0);	/* LCDD0 */
	at91_set_A_periph(AT91_PIN_PE8, 0);	/* LCDD1 */
	at91_set_A_periph(AT91_PIN_PE9, 0);	/* LCDD2 */
	at91_set_A_periph(AT91_PIN_PE10, 0);	/* LCDD3 */
	at91_set_A_periph(AT91_PIN_PE11, 0);	/* LCDD4 */
	at91_set_A_periph(AT91_PIN_PE12, 0);	/* LCDD5 */
	at91_set_A_periph(AT91_PIN_PE13, 0);	/* LCDD6 */
	at91_set_A_periph(AT91_PIN_PE14, 0);	/* LCDD7 */
	at91_set_A_periph(AT91_PIN_PE15, 0);	/* LCDD8 */
	at91_set_A_periph(AT91_PIN_PE16, 0);	/* LCDD9 */
	at91_set_A_periph(AT91_PIN_PE17, 0);	/* LCDD10 */
	at91_set_A_periph(AT91_PIN_PE18, 0);	/* LCDD11 */
	at91_set_A_periph(AT91_PIN_PE19, 0);	/* LCDD12 */
	at91_set_B_periph(AT91_PIN_PE20, 0);	/* LCDD13 */
	at91_set_A_periph(AT91_PIN_PE21, 0);	/* LCDD14 */
	at91_set_A_periph(AT91_PIN_PE22, 0);	/* LCDD15 */
	at91_set_A_periph(AT91_PIN_PE23, 0);	/* LCDD16 */
	at91_set_A_periph(AT91_PIN_PE24, 0);	/* LCDD17 */
	at91_set_A_periph(AT91_PIN_PE25, 0);	/* LCDD18 */
	at91_set_A_periph(AT91_PIN_PE26, 0);	/* LCDD19 */
	at91_set_A_periph(AT91_PIN_PE27, 0);	/* LCDD20 */
	at91_set_B_periph(AT91_PIN_PE28, 0);	/* LCDD21 */
	at91_set_A_periph(AT91_PIN_PE29, 0);	/* LCDD22 */
	at91_set_A_periph(AT91_PIN_PE30, 0);	/* LCDD23 */

	at91_periph_clk_enable(ATMEL_ID_LCDC);

	/* board specific(not enough SRAM) */
	gd->fb_base = 0x73E00000;
}

#ifdef CONFIG_LCD_INFO
#include <nand.h>
#include <version.h>

void lcd_show_board_info(void)
{
	ulong dram_size, nand_size;
	int i;
	char temp[32];

	lcd_printf ("%s\n", U_BOOT_VERSION);
	lcd_printf ("(C) 2008 ATMEL Corp\n");
	lcd_printf ("at91support@atmel.com\n");
	lcd_printf ("%s CPU at %s MHz\n",
		ATMEL_CPU_NAME,
		strmhz(temp, get_cpu_clk_rate()));

	dram_size = 0;
	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
		dram_size += gd->bd->bi_dram[i].size;
	nand_size = 0;
	for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
		nand_size += get_nand_dev_by_index(i)->size;
	lcd_printf ("  %ld MB SDRAM, %ld MB NAND\n",
		dram_size >> 20,
		nand_size >> 20 );
}
#endif /* CONFIG_LCD_INFO */
#endif

#ifdef CONFIG_DEBUG_UART_BOARD_INIT
void board_debug_uart_init(void)
{
	at91_seriald_hw_init();
}
#endif

#ifdef CONFIG_BOARD_EARLY_INIT_F
int board_early_init_f(void)
{
	return 0;
}
#endif

int board_init(void)
{
	/* arch number of AT91SAM9M10G45EK-Board */
	gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9M10G45EK;

	/* adress of boot parameters */
	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;

#ifdef CONFIG_CMD_NAND
	at91sam9m10g45ek_nand_hw_init();
#endif
#ifdef CONFIG_CMD_USB
	at91sam9m10g45ek_usb_hw_init();
#endif
#ifdef CONFIG_LCD
	at91sam9m10g45ek_lcd_hw_init();
#endif
	return 0;
}

int dram_init(void)
{
	gd->ram_size = get_ram_size((void *) CONFIG_SYS_SDRAM_BASE,
				    CONFIG_SYS_SDRAM_SIZE);
	return 0;
}

#ifdef CONFIG_RESET_PHY_R
void reset_phy(void)
{
}
#endif