ddr: marvell: a38x: Add support for DDR4 from Marvell mv-ddr-marvell repository
This syncs drivers/ddr/marvell/a38x/ with the master branch of repository
https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git
up to the commit "mv_ddr: a3700: Use the right size for memset to not overflow"
d5acc10c287e40cc2feeb28710b92e45c93c702c
This patch was created by following steps:
1. Replace all a38x files in U-Boot tree by files from upstream github
Marvell mv-ddr-marvell repository.
2. Run following command to omit portions not relevant for a38x, ddr3, and ddr4:
files=drivers/ddr/marvell/a38x/*
unifdef -m -UMV_DDR -UMV_DDR_ATF -UCONFIG_APN806 \
-UCONFIG_MC_STATIC -UCONFIG_MC_STATIC_PRINT -UCONFIG_PHY_STATIC \
-UCONFIG_PHY_STATIC_PRINT -UCONFIG_CUSTOMER_BOARD_SUPPORT \
-UCONFIG_A3700 -UA3900 -UA80X0 -UA70X0 -DCONFIG_ARMADA_38X -UCONFIG_ARMADA_39X \
-UCONFIG_64BIT $files
3. Manually change license to SPDX-License-Identifier
(upstream license in upstream github repository contains long license
texts and U-Boot is using just SPDX-License-Identifier.
After applying this patch, a38x, ddr3, and ddr4 code in upstream Marvell github
repository and in U-Boot would be fully identical. So in future applying
above steps could be used to sync code again.
The only change in this patch are:
1. Some fixes with include files.
2. Some function return and basic type defines changes in
mv_ddr_plat.c (to correct Marvell bug).
3. Remove of dead code in newly copied files (as a result of the
filter script stripping out everything other than a38x, dd3, and ddr4).
Reference:
"ddr: marvell: a38x: Sync code with Marvell mv-ddr-marvell repository"
https://source.denx.de/u-boot/u-boot/-/commit/107c3391b95bcc2ba09a876da4fa0c31b6c1e460
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
diff --git a/drivers/ddr/marvell/a38x/ddr3_init.h b/drivers/ddr/marvell/a38x/ddr3_init.h
index 055516b..ba9f788 100644
--- a/drivers/ddr/marvell/a38x/ddr3_init.h
+++ b/drivers/ddr/marvell/a38x/ddr3_init.h
@@ -137,6 +137,10 @@
extern u32 nominal_avs;
extern u32 extension_avs;
+#if defined(CONFIG_DDR4)
+/* if 1, SSTL & POD have same Vref and workaround is required */
+extern u8 vref_calibration_wa;
+#endif /* CONFIG_DDR4 */
/* Prototypes */
int ddr3_init(void);
@@ -152,6 +156,13 @@
int ddr3_tip_reg_write(u32 dev_num, u32 reg_addr, u32 data);
int ddr3_tip_reg_read(u32 dev_num, u32 reg_addr, u32 *data, u32 reg_mask);
int ddr3_silicon_get_ddr_target_freq(u32 *ddr_freq);
+#if defined(CONFIG_DDR4)
+int mv_ddr4_mode_regs_init(u8 dev_num);
+int mv_ddr4_sdram_config(u32 dev_num);
+int mv_ddr4_phy_config(u32 dev_num);
+int mv_ddr4_calibration_adjust(u32 dev_num, u8 vref_en, u8 pod_only);
+int mv_ddr4_training_main_flow(u32 dev_num);
+#endif /* CONFIG_DDR4 */
int print_adll(u32 dev_num, u32 adll[MAX_INTERFACE_NUM * MAX_BUS_NUM]);
int print_ph(u32 dev_num, u32 adll[MAX_INTERFACE_NUM * MAX_BUS_NUM]);
@@ -188,5 +199,8 @@
unsigned int mv_ddr_misl_phy_drv_ctrl_n_get(void);
unsigned int mv_ddr_misl_phy_odt_p_get(void);
unsigned int mv_ddr_misl_phy_odt_n_get(void);
+#if defined(CONFIG_DDR4)
+void refresh(void);
+#endif
#endif /* _DDR3_INIT_H */