diff --git a/board/musenki/README b/board/musenki/README
new file mode 100644
index 0000000..4a1955d
--- /dev/null
+++ b/board/musenki/README
@@ -0,0 +1,301 @@
+U-Boot for a Musenki M-3/M-1 board
+---------------------------
+
+Musenki M-1 and M-3 have two banks of flash of 4MB or 8MB each.
+
+In board's notation, bank 0 is the one at the address of 0xFF800000
+and bank 1 is the one at the address of 0xFF000000.
+
+On power-up the processor jumps to the address of 0xFFF00100, the last
+megabyte of the bank 0 of flash.
+
+Thus, U-Boot is configured to reside in flash starting at the address of
+0xFFF00000.  The environment space is located in flash separately from
+U-Boot, at the address of 0xFF800000.
+
+There is a Davicom 9102A on-board, but I don't have it working yet.
+
+U-Boot test results
+--------------------
+
+x.x Operation on all available serial consoles
+
+x.x.x CONFIG_CONS_INDEX 1
+
+
+U-Boot 1.1.1 (Nov 20 2001 - 15:55:32)
+
+CPU:   MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache
+Board: MUSENKI Local Bus at 100 MHz
+DRAM:  32 MB
+FLASH:  4 MB
+In:    serial
+Out:   serial
+Err:   serial
+Hit any key to stop autoboot:  0
+=> help
+autoscr - run script from memory
+base    - print or set address offset
+bdinfo  - print Board Info structure
+bootm   - boot application image from memory
+bootp   - boot image via network using BootP/TFTP protocol
+bootd   - boot default, i.e., run 'bootcmd'
+cmp     - memory compare
+coninfo - print console devices and informations
+cp      - memory copy
+crc32   - checksum calculation
+dcache  - enable or disable data cache
+echo    - echo args to console
+erase   - erase FLASH memory
+flinfo  - print FLASH memory information
+go      - start application at address 'addr'
+help    - print online help
+icache  - enable or disable instruction cache
+iminfo  - print header information for application image
+loadb   - load binary file over serial line (kermit mode)
+loads   - load S-Record file over serial line
+loop    - infinite loop on address range
+md      - memory display
+mm      - memory modify (auto-incrementing)
+mtest   - simple RAM test
+mw      - memory write (fill)
+nm      - memory modify (constant address)
+printenv- print environment variables
+protect - enable or disable FLASH write protection
+rarpboot- boot image via network using RARP/TFTP protocol
+reset   - Perform RESET of the CPU
+run     - run commands in an environment variable
+saveenv - save environment variables to persistent storage
+setenv  - set environment variables
+tftpboot- boot image via network using TFTP protocol
+               and env variables ipaddr and serverip
+version - print monitor version
+?       - alias for 'help'
+
+
+
+x.x.x CONFIG_CONS_INDEX 2
+
+**** NOT TESTED ****
+
+x.x Flash Driver Operation
+
+
+Boot 1.1.1 (Nov 20 2001 - 15:55:32)
+
+CPU:   MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache
+Board: MUSENKI Local Bus at 100 MHz
+DRAM:  32 MB
+FLASH:  4 MB
+*** Warning - bad CRC, using default environment
+
+In:    serial
+Out:   serial
+Err:   serial
+Hit any key to stop autoboot:  0
+=>
+=> md ff800000
+ff800000: 46989bf8 626f6f74 636d643d 626f6f74    F...bootcmd=boot
+ff800010: 6d204646 38323030 30300062 6f6f7464    m FF820000.bootd
+ff800020: 656c6179 3d350062 61756472 6174653d    elay=5.baudrate=
+ff800030: 39363030 00636c6f 636b735f 696e5f6d    9600.clocks_in_m
+ff800040: 687a3d31 00737464 696e3d73 65726961    hz=1.stdin=seria
+ff800050: 6c007374 646f7574 3d736572 69616c00    l.stdout=serial.
+ff800060: 73746465 72723d73 65726961 6c006970    stderr=serial.ip
+ff800070: 61646472 3d313932 2e313638 2e302e34    addr=192.168.0.4
+ff800080: 32007365 72766572 69703d31 39322e31    2.serverip=192.1
+ff800090: 36382e30 2e380000 00000000 00000000    68.0.8..........
+ff8000a0: 00000000 00000000 00000000 00000000    ................
+ff8000b0: 00000000 00000000 00000000 00000000    ................
+ff8000c0: 00000000 00000000 00000000 00000000    ................
+ff8000d0: 00000000 00000000 00000000 00000000    ................
+ff8000e0: 00000000 00000000 00000000 00000000    ................
+ff8000f0: 00000000 00000000 00000000 00000000    ................
+=> protect off ff800000 ff81ffff
+Un-Protected 1 sectors
+=> erase ff800000 ff81ffff
+Erase Flash from 0xff800000 to 0xff81ffff
+ done
+Erased 1 sectors
+=> md ff800000
+ff800000: ffffffff ffffffff ffffffff ffffffff    ................
+ff800010: ffffffff ffffffff ffffffff ffffffff    ................
+ff800020: ffffffff ffffffff ffffffff ffffffff    ................
+ff800030: ffffffff ffffffff ffffffff ffffffff    ................
+ff800040: ffffffff ffffffff ffffffff ffffffff    ................
+ff800050: ffffffff ffffffff ffffffff ffffffff    ................
+ff800060: ffffffff ffffffff ffffffff ffffffff    ................
+ff800070: ffffffff ffffffff ffffffff ffffffff    ................
+ff800080: ffffffff ffffffff ffffffff ffffffff    ................
+ff800090: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000a0: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000b0: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000c0: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000d0: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000e0: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000f0: ffffffff ffffffff ffffffff ffffffff    ................
+
+x.x.x Information
+
+
+U-Boot 1.1.1 (Nov 20 2001 - 15:55:32)
+
+CPU:   MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache
+Board: MUSENKI Local Bus at 100 MHz
+DRAM:  32 MB
+FLASH:  4 MB
+*** Warning - bad CRC, using default environment
+
+In:    serial
+Out:   serial
+Err:   serial
+Hit any key to stop autoboot:  0
+=> flinfo
+
+Bank # 1: Intel 28F320J3A (32Mbit = 128K x 32)
+  Size: 4 MB in 32 Sectors
+  Sector Start Addresses:
+    FF800000 (RO) FF820000      FF840000      FF860000      FF880000
+    FF8A0000      FF8C0000      FF8E0000      FF900000      FF920000
+    FF940000      FF960000      FF980000      FF9A0000      FF9C0000
+    FF9E0000      FFA00000      FFA20000      FFA40000      FFA60000
+    FFA80000      FFAA0000      FFAC0000      FFAE0000      FFB00000
+    FFB20000      FFB40000      FFB60000      FFB80000      FFBA0000
+    FFBC0000      FFBE0000
+
+Bank # 2: missing or unknown FLASH type
+=>
+
+
+
+x.x.x Flash Programming
+
+
+U-Boot 1.1.1 (Nov 20 2001 - 15:55:32)
+
+CPU:   MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache
+Board: MUSENKI Local Bus at 100 MHz
+DRAM:  32 MB
+FLASH:  4 MB
+
+In:    serial
+Out:   serial
+Err:   serial
+Hit any key to stop autoboot:  0
+=>
+=>
+=>
+=> protect off ff800000 ff81ffff
+Un-Protected 1 sectors
+=> cp 0 ff800000 20
+Copy to Flash... done
+=> md ff800000
+ff800000: 37ce33ec 33cc334c 33c031cc 33cc35cc    7.3.3.3L3.1.3.5.
+ff800010: 33ec13ce 30ccb3ec b3c833c4 31c836cc    3...0.....3.1.6.
+ff800020: 33cc3b9d 31ec33ee 13ecf3cc 338833ec    3.;.1.3.....3.3.
+ff800030: 234c33ec 32cc22cc 33883bdc 534433cc    #L3.2.".3.;.SD3.
+ff800040: 33cc30c8 31cc32ec 338c33cc 330c33dc    3.0.1.2.3.3.3.3.
+ff800050: 33cc13dc 334c534c b1c433d8 128c13cc    3...3LSL..3.....
+ff800060: 37ec36cd 33dc33cc bbc9f7e8 bbcc77cc    7.6.3.3.......w.
+ff800070: 314c0adc 139c30ed 33cc334c 33c833ec    1L....0.3.3L3.3.
+ff800080: ffffffff ffffffff ffffffff ffffffff    ................
+ff800090: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000a0: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000b0: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000c0: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000d0: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000e0: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000f0: ffffffff ffffffff ffffffff ffffffff    ................
+
+
+x.x.x Storage of environment variables in flash
+
+
+U-Boot 1.1.1 (Nov 20 2001 - 15:55:32)
+
+CPU:   MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache
+Board: MUSENKI Local Bus at 100 MHz
+DRAM:  32 MB
+FLASH:  4 MB
+In:    serial
+Out:   serial
+Err:   serial
+Hit any key to stop autoboot:  0
+=> printenv
+bootcmd=bootm FF820000
+bootdelay=5
+baudrate=9600
+clocks_in_mhz=1
+stdin=serial
+stdout=serial
+stderr=serial
+
+Environment size: 106/16380 bytes
+=> setenv myvar 1234
+=> saveenv
+Un-Protected 1 sectors
+Erasing Flash...
+ done
+Erased 1 sectors
+Saving Environment to Flash...
+Protected 1 sectors
+=> reset
+
+
+U-Boot 1.1.1 (Nov 20 2001 - 15:55:32)
+
+CPU:   MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache
+Board: MUSENKI Local Bus at 100 MHz
+DRAM:  32 MB
+FLASH:  4 MB
+In:    serial
+Out:   serial
+Err:   serial
+Hit any key to stop autoboot:  0
+=> printenv
+bootcmd=bootm FF820000
+bootdelay=5
+baudrate=9600
+clocks_in_mhz=1
+myvar=1234
+stdin=serial
+stdout=serial
+stderr=serial
+
+Environment size: 117/16380 bytes
+
+x.x Image Download and run over serial port
+
+
+U-Boot 1.1.1 (Nov 20 2001 - 15:55:32)
+
+CPU:   MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache
+Board: MUSENKI Local Bus at 100 MHz
+DRAM:  32 MB
+FLASH:  4 MB
+In:    serial
+Out:   serial
+Err:   serial
+Hit any key to stop autoboot:  0
+=> loads
+## Ready for S-Record download ...
+
+## First Load Addr = 0x00040000
+## Last  Load Addr = 0x00050177
+## Total Size      = 0x00010178 = 65912 Bytes
+## Start Addr      = 0x00040004
+=> go 40004
+## Starting application at 0x00040004 ...
+Hello World
+argc = 1
+argv[0] = "40004"
+argv[1] = "<NULL>"
+Hit any key to exit ...
+
+## Application terminated, rc = 0x0
+
+
+x.x Image download and run over ethernet interface
+
+untested (not working yet, actually)
+