diff --git a/cmd/ide.c b/cmd/ide.c
index db26f43..c942744 100644
--- a/cmd/ide.c
+++ b/cmd/ide.c
@@ -29,717 +29,9 @@
 # include <status_led.h>
 #endif
 
-#ifdef __PPC__
-# define EIEIO		__asm__ volatile ("eieio")
-# define SYNC		__asm__ volatile ("sync")
-#else
-# define EIEIO		/* nothing */
-# define SYNC		/* nothing */
-#endif
-
-/* ------------------------------------------------------------------------- */
-
 /* Current I/O Device	*/
 static int curr_device = -1;
 
-/* Current offset for IDE0 / IDE1 bus access	*/
-ulong ide_bus_offset[CONFIG_SYS_IDE_MAXBUS] = {
-#if defined(CONFIG_SYS_ATA_IDE0_OFFSET)
-	CONFIG_SYS_ATA_IDE0_OFFSET,
-#endif
-#if defined(CONFIG_SYS_ATA_IDE1_OFFSET) && (CONFIG_SYS_IDE_MAXBUS > 1)
-	CONFIG_SYS_ATA_IDE1_OFFSET,
-#endif
-};
-
-static int ide_bus_ok[CONFIG_SYS_IDE_MAXBUS];
-
-struct blk_desc ide_dev_desc[CONFIG_SYS_IDE_MAXDEVICE];
-/* ------------------------------------------------------------------------- */
-
-#define IDE_TIME_OUT	2000	/* 2 sec timeout */
-
-#define ATAPI_TIME_OUT	7000	/* 7 sec timeout (5 sec seems to work...) */
-
-#define IDE_SPIN_UP_TIME_OUT 5000 /* 5 sec spin-up timeout */
-
-#ifndef CONFIG_SYS_ATA_PORT_ADDR
-#define CONFIG_SYS_ATA_PORT_ADDR(port) (port)
-#endif
-
-#ifndef CONFIG_IDE_LED	/* define LED macros, they are not used anyways */
-# define DEVICE_LED(x) 0
-# define LED_IDE1 1
-# define LED_IDE2 2
-#endif
-
-#ifdef CONFIG_IDE_RESET
-extern void ide_set_reset(int idereset);
-
-static void ide_reset(void)
-{
-	int i;
-
-	curr_device = -1;
-	for (i = 0; i < CONFIG_SYS_IDE_MAXBUS; ++i)
-		ide_bus_ok[i] = 0;
-	for (i = 0; i < CONFIG_SYS_IDE_MAXDEVICE; ++i)
-		ide_dev_desc[i].type = DEV_TYPE_UNKNOWN;
-
-	ide_set_reset(1);	/* assert reset */
-
-	/* the reset signal shall be asserted for et least 25 us */
-	udelay(25);
-
-	WATCHDOG_RESET();
-
-	/* de-assert RESET signal */
-	ide_set_reset(0);
-
-	/* wait 250 ms */
-	for (i = 0; i < 250; ++i)
-		udelay(1000);
-}
-#else
-#define ide_reset()	/* dummy */
-#endif /* CONFIG_IDE_RESET */
-
-/*
- * Wait until Busy bit is off, or timeout (in ms)
- * Return last status
- */
-static uchar ide_wait(int dev, ulong t)
-{
-	ulong delay = 10 * t;	/* poll every 100 us */
-	uchar c;
-
-	while ((c = ide_inb(dev, ATA_STATUS)) & ATA_STAT_BUSY) {
-		udelay(100);
-		if (delay-- == 0)
-			break;
-	}
-	return c;
-}
-
-/*
- * copy src to dest, skipping leading and trailing blanks and null
- * terminate the string
- * "len" is the size of available memory including the terminating '\0'
- */
-static void ident_cpy(unsigned char *dst, unsigned char *src,
-		      unsigned int len)
-{
-	unsigned char *end, *last;
-
-	last = dst;
-	end = src + len - 1;
-
-	/* reserve space for '\0' */
-	if (len < 2)
-		goto OUT;
-
-	/* skip leading white space */
-	while ((*src) && (src < end) && (*src == ' '))
-		++src;
-
-	/* copy string, omitting trailing white space */
-	while ((*src) && (src < end)) {
-		*dst++ = *src;
-		if (*src++ != ' ')
-			last = dst;
-	}
-OUT:
-	*last = '\0';
-}
-
-#ifdef CONFIG_ATAPI
-/****************************************************************************
- * ATAPI Support
- */
-
-#if defined(CONFIG_IDE_SWAP_IO)
-/* since ATAPI may use commands with not 4 bytes alligned length
- * we have our own transfer functions, 2 bytes alligned */
-__weak void ide_output_data_shorts(int dev, ushort *sect_buf, int shorts)
-{
-	ushort *dbuf;
-	volatile ushort *pbuf;
-
-	pbuf = (ushort *)(ATA_CURR_BASE(dev) + ATA_DATA_REG);
-	dbuf = (ushort *)sect_buf;
-
-	debug("in output data shorts base for read is %lx\n",
-	      (unsigned long) pbuf);
-
-	while (shorts--) {
-		EIEIO;
-		*pbuf = *dbuf++;
-	}
-}
-
-__weak void ide_input_data_shorts(int dev, ushort *sect_buf, int shorts)
-{
-	ushort *dbuf;
-	volatile ushort *pbuf;
-
-	pbuf = (ushort *)(ATA_CURR_BASE(dev) + ATA_DATA_REG);
-	dbuf = (ushort *)sect_buf;
-
-	debug("in input data shorts base for read is %lx\n",
-	      (unsigned long) pbuf);
-
-	while (shorts--) {
-		EIEIO;
-		*dbuf++ = *pbuf;
-	}
-}
-
-#else  /* ! CONFIG_IDE_SWAP_IO */
-__weak void ide_output_data_shorts(int dev, ushort *sect_buf, int shorts)
-{
-	outsw(ATA_CURR_BASE(dev) + ATA_DATA_REG, sect_buf, shorts);
-}
-
-__weak void ide_input_data_shorts(int dev, ushort *sect_buf, int shorts)
-{
-	insw(ATA_CURR_BASE(dev) + ATA_DATA_REG, sect_buf, shorts);
-}
-
-#endif /* CONFIG_IDE_SWAP_IO */
-
-/*
- * Wait until (Status & mask) == res, or timeout (in ms)
- * Return last status
- * This is used since some ATAPI CD ROMs clears their Busy Bit first
- * and then they set their DRQ Bit
- */
-static uchar atapi_wait_mask(int dev, ulong t, uchar mask, uchar res)
-{
-	ulong delay = 10 * t;	/* poll every 100 us */
-	uchar c;
-
-	/* prevents to read the status before valid */
-	c = ide_inb(dev, ATA_DEV_CTL);
-
-	while (((c = ide_inb(dev, ATA_STATUS)) & mask) != res) {
-		/* break if error occurs (doesn't make sense to wait more) */
-		if ((c & ATA_STAT_ERR) == ATA_STAT_ERR)
-			break;
-		udelay(100);
-		if (delay-- == 0)
-			break;
-	}
-	return c;
-}
-
-/*
- * issue an atapi command
- */
-unsigned char atapi_issue(int device, unsigned char *ccb, int ccblen,
-			  unsigned char *buffer, int buflen)
-{
-	unsigned char c, err, mask, res;
-	int n;
-
-	ide_led(DEVICE_LED(device), 1);	/* LED on       */
-
-	/* Select device
-	 */
-	mask = ATA_STAT_BUSY | ATA_STAT_DRQ;
-	res = 0;
-	ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
-	c = atapi_wait_mask(device, ATAPI_TIME_OUT, mask, res);
-	if ((c & mask) != res) {
-		printf("ATAPI_ISSUE: device %d not ready status %X\n", device,
-		       c);
-		err = 0xFF;
-		goto AI_OUT;
-	}
-	/* write taskfile */
-	ide_outb(device, ATA_ERROR_REG, 0);	/* no DMA, no overlaped */
-	ide_outb(device, ATA_SECT_CNT, 0);
-	ide_outb(device, ATA_SECT_NUM, 0);
-	ide_outb(device, ATA_CYL_LOW, (unsigned char) (buflen & 0xFF));
-	ide_outb(device, ATA_CYL_HIGH,
-		 (unsigned char) ((buflen >> 8) & 0xFF));
-	ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
-
-	ide_outb(device, ATA_COMMAND, ATAPI_CMD_PACKET);
-	udelay(50);
-
-	mask = ATA_STAT_DRQ | ATA_STAT_BUSY | ATA_STAT_ERR;
-	res = ATA_STAT_DRQ;
-	c = atapi_wait_mask(device, ATAPI_TIME_OUT, mask, res);
-
-	if ((c & mask) != res) {	/* DRQ must be 1, BSY 0 */
-		printf("ATAPI_ISSUE: Error (no IRQ) before sending ccb dev %d status 0x%02x\n",
-		       device, c);
-		err = 0xFF;
-		goto AI_OUT;
-	}
-
-	/* write command block */
-	ide_output_data_shorts(device, (unsigned short *)ccb, ccblen / 2);
-
-	/* ATAPI Command written wait for completition */
-	udelay(5000);		/* device must set bsy */
-
-	mask = ATA_STAT_DRQ | ATA_STAT_BUSY | ATA_STAT_ERR;
-	/*
-	 * if no data wait for DRQ = 0 BSY = 0
-	 * if data wait for DRQ = 1 BSY = 0
-	 */
-	res = 0;
-	if (buflen)
-		res = ATA_STAT_DRQ;
-	c = atapi_wait_mask(device, ATAPI_TIME_OUT, mask, res);
-	if ((c & mask) != res) {
-		if (c & ATA_STAT_ERR) {
-			err = (ide_inb(device, ATA_ERROR_REG)) >> 4;
-			debug("atapi_issue 1 returned sense key %X status %02X\n",
-			      err, c);
-		} else {
-			printf("ATAPI_ISSUE: (no DRQ) after sending ccb (%x)  status 0x%02x\n",
-			       ccb[0], c);
-			err = 0xFF;
-		}
-		goto AI_OUT;
-	}
-	n = ide_inb(device, ATA_CYL_HIGH);
-	n <<= 8;
-	n += ide_inb(device, ATA_CYL_LOW);
-	if (n > buflen) {
-		printf("ERROR, transfer bytes %d requested only %d\n", n,
-		       buflen);
-		err = 0xff;
-		goto AI_OUT;
-	}
-	if ((n == 0) && (buflen < 0)) {
-		printf("ERROR, transfer bytes %d requested %d\n", n, buflen);
-		err = 0xff;
-		goto AI_OUT;
-	}
-	if (n != buflen) {
-		debug("WARNING, transfer bytes %d not equal with requested %d\n",
-		      n, buflen);
-	}
-	if (n != 0) {		/* data transfer */
-		debug("ATAPI_ISSUE: %d Bytes to transfer\n", n);
-		/* we transfer shorts */
-		n >>= 1;
-		/* ok now decide if it is an in or output */
-		if ((ide_inb(device, ATA_SECT_CNT) & 0x02) == 0) {
-			debug("Write to device\n");
-			ide_output_data_shorts(device, (unsigned short *)buffer,
-					       n);
-		} else {
-			debug("Read from device @ %p shorts %d\n", buffer, n);
-			ide_input_data_shorts(device, (unsigned short *)buffer,
-					      n);
-		}
-	}
-	udelay(5000);		/* seems that some CD ROMs need this... */
-	mask = ATA_STAT_BUSY | ATA_STAT_ERR;
-	res = 0;
-	c = atapi_wait_mask(device, ATAPI_TIME_OUT, mask, res);
-	if ((c & ATA_STAT_ERR) == ATA_STAT_ERR) {
-		err = (ide_inb(device, ATA_ERROR_REG) >> 4);
-		debug("atapi_issue 2 returned sense key %X status %X\n", err,
-		      c);
-	} else {
-		err = 0;
-	}
-AI_OUT:
-	ide_led(DEVICE_LED(device), 0);	/* LED off      */
-	return err;
-}
-
-/*
- * sending the command to atapi_issue. If an status other than good
- * returns, an request_sense will be issued
- */
-
-#define ATAPI_DRIVE_NOT_READY	100
-#define ATAPI_UNIT_ATTN		10
-
-unsigned char atapi_issue_autoreq(int device,
-				  unsigned char *ccb,
-				  int ccblen,
-				  unsigned char *buffer, int buflen)
-{
-	unsigned char sense_data[18], sense_ccb[12];
-	unsigned char res, key, asc, ascq;
-	int notready, unitattn;
-
-	unitattn = ATAPI_UNIT_ATTN;
-	notready = ATAPI_DRIVE_NOT_READY;
-
-retry:
-	res = atapi_issue(device, ccb, ccblen, buffer, buflen);
-	if (res == 0)
-		return 0;	/* Ok */
-
-	if (res == 0xFF)
-		return 0xFF;	/* error */
-
-	debug("(auto_req)atapi_issue returned sense key %X\n", res);
-
-	memset(sense_ccb, 0, sizeof(sense_ccb));
-	memset(sense_data, 0, sizeof(sense_data));
-	sense_ccb[0] = ATAPI_CMD_REQ_SENSE;
-	sense_ccb[4] = 18;	/* allocation Length */
-
-	res = atapi_issue(device, sense_ccb, 12, sense_data, 18);
-	key = (sense_data[2] & 0xF);
-	asc = (sense_data[12]);
-	ascq = (sense_data[13]);
-
-	debug("ATAPI_CMD_REQ_SENSE returned %x\n", res);
-	debug(" Sense page: %02X key %02X ASC %02X ASCQ %02X\n",
-	      sense_data[0], key, asc, ascq);
-
-	if ((key == 0))
-		return 0;	/* ok device ready */
-
-	if ((key == 6) || (asc == 0x29) || (asc == 0x28)) { /* Unit Attention */
-		if (unitattn-- > 0) {
-			udelay(200 * 1000);
-			goto retry;
-		}
-		printf("Unit Attention, tried %d\n", ATAPI_UNIT_ATTN);
-		goto error;
-	}
-	if ((asc == 0x4) && (ascq == 0x1)) {
-		/* not ready, but will be ready soon */
-		if (notready-- > 0) {
-			udelay(200 * 1000);
-			goto retry;
-		}
-		printf("Drive not ready, tried %d times\n",
-		       ATAPI_DRIVE_NOT_READY);
-		goto error;
-	}
-	if (asc == 0x3a) {
-		debug("Media not present\n");
-		goto error;
-	}
-
-	printf("ERROR: Unknown Sense key %02X ASC %02X ASCQ %02X\n", key, asc,
-	       ascq);
-error:
-	debug("ERROR Sense key %02X ASC %02X ASCQ %02X\n", key, asc, ascq);
-	return 0xFF;
-}
-
-/*
- * atapi_read:
- * we transfer only one block per command, since the multiple DRQ per
- * command is not yet implemented
- */
-#define ATAPI_READ_MAX_BYTES	2048	/* we read max 2kbytes */
-#define ATAPI_READ_BLOCK_SIZE	2048	/* assuming CD part */
-#define ATAPI_READ_MAX_BLOCK	(ATAPI_READ_MAX_BYTES/ATAPI_READ_BLOCK_SIZE)
-
-ulong atapi_read(struct blk_desc *block_dev, lbaint_t blknr, lbaint_t blkcnt,
-		 void *buffer)
-{
-	int device = block_dev->devnum;
-	ulong n = 0;
-	unsigned char ccb[12];	/* Command descriptor block */
-	ulong cnt;
-
-	debug("atapi_read dev %d start " LBAF " blocks " LBAF
-	      " buffer at %lX\n", device, blknr, blkcnt, (ulong) buffer);
-
-	do {
-		if (blkcnt > ATAPI_READ_MAX_BLOCK)
-			cnt = ATAPI_READ_MAX_BLOCK;
-		else
-			cnt = blkcnt;
-
-		ccb[0] = ATAPI_CMD_READ_12;
-		ccb[1] = 0;	/* reserved */
-		ccb[2] = (unsigned char) (blknr >> 24) & 0xFF;	/* MSB Block */
-		ccb[3] = (unsigned char) (blknr >> 16) & 0xFF;	/*  */
-		ccb[4] = (unsigned char) (blknr >> 8) & 0xFF;
-		ccb[5] = (unsigned char) blknr & 0xFF;	/* LSB Block */
-		ccb[6] = (unsigned char) (cnt >> 24) & 0xFF; /* MSB Block cnt */
-		ccb[7] = (unsigned char) (cnt >> 16) & 0xFF;
-		ccb[8] = (unsigned char) (cnt >> 8) & 0xFF;
-		ccb[9] = (unsigned char) cnt & 0xFF;	/* LSB Block */
-		ccb[10] = 0;	/* reserved */
-		ccb[11] = 0;	/* reserved */
-
-		if (atapi_issue_autoreq(device, ccb, 12,
-					(unsigned char *)buffer,
-					cnt * ATAPI_READ_BLOCK_SIZE)
-		    == 0xFF) {
-			return n;
-		}
-		n += cnt;
-		blkcnt -= cnt;
-		blknr += cnt;
-		buffer += (cnt * ATAPI_READ_BLOCK_SIZE);
-	} while (blkcnt > 0);
-	return n;
-}
-
-static void atapi_inquiry(struct blk_desc *dev_desc)
-{
-	unsigned char ccb[12];	/* Command descriptor block */
-	unsigned char iobuf[64];	/* temp buf */
-	unsigned char c;
-	int device;
-
-	device = dev_desc->devnum;
-	dev_desc->type = DEV_TYPE_UNKNOWN;	/* not yet valid */
-	dev_desc->block_read = atapi_read;
-
-	memset(ccb, 0, sizeof(ccb));
-	memset(iobuf, 0, sizeof(iobuf));
-
-	ccb[0] = ATAPI_CMD_INQUIRY;
-	ccb[4] = 40;		/* allocation Legnth */
-	c = atapi_issue_autoreq(device, ccb, 12, (unsigned char *)iobuf, 40);
-
-	debug("ATAPI_CMD_INQUIRY returned %x\n", c);
-	if (c != 0)
-		return;
-
-	/* copy device ident strings */
-	ident_cpy((unsigned char *)dev_desc->vendor, &iobuf[8], 8);
-	ident_cpy((unsigned char *)dev_desc->product, &iobuf[16], 16);
-	ident_cpy((unsigned char *)dev_desc->revision, &iobuf[32], 5);
-
-	dev_desc->lun = 0;
-	dev_desc->lba = 0;
-	dev_desc->blksz = 0;
-	dev_desc->log2blksz = LOG2_INVALID(typeof(dev_desc->log2blksz));
-	dev_desc->type = iobuf[0] & 0x1f;
-
-	if ((iobuf[1] & 0x80) == 0x80)
-		dev_desc->removable = 1;
-	else
-		dev_desc->removable = 0;
-
-	memset(ccb, 0, sizeof(ccb));
-	memset(iobuf, 0, sizeof(iobuf));
-	ccb[0] = ATAPI_CMD_START_STOP;
-	ccb[4] = 0x03;		/* start */
-
-	c = atapi_issue_autoreq(device, ccb, 12, (unsigned char *)iobuf, 0);
-
-	debug("ATAPI_CMD_START_STOP returned %x\n", c);
-	if (c != 0)
-		return;
-
-	memset(ccb, 0, sizeof(ccb));
-	memset(iobuf, 0, sizeof(iobuf));
-	c = atapi_issue_autoreq(device, ccb, 12, (unsigned char *)iobuf, 0);
-
-	debug("ATAPI_CMD_UNIT_TEST_READY returned %x\n", c);
-	if (c != 0)
-		return;
-
-	memset(ccb, 0, sizeof(ccb));
-	memset(iobuf, 0, sizeof(iobuf));
-	ccb[0] = ATAPI_CMD_READ_CAP;
-	c = atapi_issue_autoreq(device, ccb, 12, (unsigned char *)iobuf, 8);
-	debug("ATAPI_CMD_READ_CAP returned %x\n", c);
-	if (c != 0)
-		return;
-
-	debug("Read Cap: LBA %02X%02X%02X%02X blksize %02X%02X%02X%02X\n",
-	      iobuf[0], iobuf[1], iobuf[2], iobuf[3],
-	      iobuf[4], iobuf[5], iobuf[6], iobuf[7]);
-
-	dev_desc->lba = ((unsigned long) iobuf[0] << 24) +
-		((unsigned long) iobuf[1] << 16) +
-		((unsigned long) iobuf[2] << 8) + ((unsigned long) iobuf[3]);
-	dev_desc->blksz = ((unsigned long) iobuf[4] << 24) +
-		((unsigned long) iobuf[5] << 16) +
-		((unsigned long) iobuf[6] << 8) + ((unsigned long) iobuf[7]);
-	dev_desc->log2blksz = LOG2(dev_desc->blksz);
-#ifdef CONFIG_LBA48
-	/* ATAPI devices cannot use 48bit addressing (ATA/ATAPI v7) */
-	dev_desc->lba48 = 0;
-#endif
-	return;
-}
-
-#endif /* CONFIG_ATAPI */
-
-static void ide_ident(struct blk_desc *dev_desc)
-{
-	unsigned char c;
-	hd_driveid_t iop;
-
-#ifdef CONFIG_ATAPI
-	int retries = 0;
-#endif
-	int device;
-
-	device = dev_desc->devnum;
-	printf("  Device %d: ", device);
-
-	ide_led(DEVICE_LED(device), 1);	/* LED on       */
-	/* Select device
-	 */
-	ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
-	dev_desc->if_type = IF_TYPE_IDE;
-#ifdef CONFIG_ATAPI
-
-	retries = 0;
-
-	/* Warning: This will be tricky to read */
-	while (retries <= 1) {
-		/* check signature */
-		if ((ide_inb(device, ATA_SECT_CNT) == 0x01) &&
-		    (ide_inb(device, ATA_SECT_NUM) == 0x01) &&
-		    (ide_inb(device, ATA_CYL_LOW) == 0x14) &&
-		    (ide_inb(device, ATA_CYL_HIGH) == 0xEB)) {
-			/* ATAPI Signature found */
-			dev_desc->if_type = IF_TYPE_ATAPI;
-			/*
-			 * Start Ident Command
-			 */
-			ide_outb(device, ATA_COMMAND, ATAPI_CMD_IDENT);
-			/*
-			 * Wait for completion - ATAPI devices need more time
-			 * to become ready
-			 */
-			c = ide_wait(device, ATAPI_TIME_OUT);
-		} else
-#endif
-		{
-			/*
-			 * Start Ident Command
-			 */
-			ide_outb(device, ATA_COMMAND, ATA_CMD_IDENT);
-
-			/*
-			 * Wait for completion
-			 */
-			c = ide_wait(device, IDE_TIME_OUT);
-		}
-		ide_led(DEVICE_LED(device), 0);	/* LED off      */
-
-		if (((c & ATA_STAT_DRQ) == 0) ||
-		    ((c & (ATA_STAT_FAULT | ATA_STAT_ERR)) != 0)) {
-#ifdef CONFIG_ATAPI
-			{
-				/*
-				 * Need to soft reset the device
-				 * in case it's an ATAPI...
-				 */
-				debug("Retrying...\n");
-				ide_outb(device, ATA_DEV_HD,
-					 ATA_LBA | ATA_DEVICE(device));
-				udelay(100000);
-				ide_outb(device, ATA_COMMAND, 0x08);
-				udelay(500000);	/* 500 ms */
-			}
-			/*
-			 * Select device
-			 */
-			ide_outb(device, ATA_DEV_HD,
-				 ATA_LBA | ATA_DEVICE(device));
-			retries++;
-#else
-			return;
-#endif
-		}
-#ifdef CONFIG_ATAPI
-		else
-			break;
-	}			/* see above - ugly to read */
-
-	if (retries == 2)	/* Not found */
-		return;
-#endif
-
-	ide_input_swap_data(device, (ulong *)&iop, ATA_SECTORWORDS);
-
-	ident_cpy((unsigned char *)dev_desc->revision, iop.fw_rev,
-		  sizeof(dev_desc->revision));
-	ident_cpy((unsigned char *)dev_desc->vendor, iop.model,
-		  sizeof(dev_desc->vendor));
-	ident_cpy((unsigned char *)dev_desc->product, iop.serial_no,
-		  sizeof(dev_desc->product));
-#ifdef __LITTLE_ENDIAN
-	/*
-	 * firmware revision, model, and serial number have Big Endian Byte
-	 * order in Word. Convert all three to little endian.
-	 *
-	 * See CF+ and CompactFlash Specification Revision 2.0:
-	 * 6.2.1.6: Identify Drive, Table 39 for more details
-	 */
-
-	strswab(dev_desc->revision);
-	strswab(dev_desc->vendor);
-	strswab(dev_desc->product);
-#endif /* __LITTLE_ENDIAN */
-
-	if ((iop.config & 0x0080) == 0x0080)
-		dev_desc->removable = 1;
-	else
-		dev_desc->removable = 0;
-
-#ifdef CONFIG_ATAPI
-	if (dev_desc->if_type == IF_TYPE_ATAPI) {
-		atapi_inquiry(dev_desc);
-		return;
-	}
-#endif /* CONFIG_ATAPI */
-
-#ifdef __BIG_ENDIAN
-	/* swap shorts */
-	dev_desc->lba = (iop.lba_capacity << 16) | (iop.lba_capacity >> 16);
-#else  /* ! __BIG_ENDIAN */
-	/*
-	 * do not swap shorts on little endian
-	 *
-	 * See CF+ and CompactFlash Specification Revision 2.0:
-	 * 6.2.1.6: Identfy Drive, Table 39, Word Address 57-58 for details.
-	 */
-	dev_desc->lba = iop.lba_capacity;
-#endif /* __BIG_ENDIAN */
-
-#ifdef CONFIG_LBA48
-	if (iop.command_set_2 & 0x0400) {	/* LBA 48 support */
-		dev_desc->lba48 = 1;
-		dev_desc->lba = (unsigned long long) iop.lba48_capacity[0] |
-			((unsigned long long) iop.lba48_capacity[1] << 16) |
-			((unsigned long long) iop.lba48_capacity[2] << 32) |
-			((unsigned long long) iop.lba48_capacity[3] << 48);
-	} else {
-		dev_desc->lba48 = 0;
-	}
-#endif /* CONFIG_LBA48 */
-	/* assuming HD */
-	dev_desc->type = DEV_TYPE_HARDDISK;
-	dev_desc->blksz = ATA_BLOCKSIZE;
-	dev_desc->log2blksz = LOG2(dev_desc->blksz);
-	dev_desc->lun = 0;	/* just to fill something in... */
-
-#if 0				/* only used to test the powersaving mode,
-				 * if enabled, the drive goes after 5 sec
-				 * in standby mode */
-	ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
-	c = ide_wait(device, IDE_TIME_OUT);
-	ide_outb(device, ATA_SECT_CNT, 1);
-	ide_outb(device, ATA_LBA_LOW, 0);
-	ide_outb(device, ATA_LBA_MID, 0);
-	ide_outb(device, ATA_LBA_HIGH, 0);
-	ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
-	ide_outb(device, ATA_COMMAND, 0xe3);
-	udelay(50);
-	c = ide_wait(device, IDE_TIME_OUT);	/* can't take over 500 ms */
-#endif
-}
-
-/* ------------------------------------------------------------------------- */
-
 int do_ide(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[])
 {
 	int rcode = 0;
@@ -759,79 +51,41 @@
 			ide_init();
 			return 0;
 		} else if (strncmp(argv[1], "inf", 3) == 0) {
-			int i;
-
-			putc('\n');
-
-			for (i = 0; i < CONFIG_SYS_IDE_MAXDEVICE; ++i) {
-				if (ide_dev_desc[i].type == DEV_TYPE_UNKNOWN)
-					continue;  /* list only known devices */
-				printf("IDE device %d: ", i);
-				dev_print(&ide_dev_desc[i]);
-			}
+			blk_list_devices(IF_TYPE_IDE);
 			return 0;
 
 		} else if (strncmp(argv[1], "dev", 3) == 0) {
-			if (curr_device < 0 ||
-			    curr_device >= CONFIG_SYS_IDE_MAXDEVICE) {
-				puts("\nno IDE devices available\n");
-				return 1;
+			if (blk_print_device_num(IF_TYPE_IDE, curr_device)) {
+				printf("\nno IDE devices available\n");
+				return CMD_RET_FAILURE;
 			}
-			printf("\nIDE device %d: ", curr_device);
-			dev_print(&ide_dev_desc[curr_device]);
+
 			return 0;
 		} else if (strncmp(argv[1], "part", 4) == 0) {
-			int dev, ok;
-
-			for (ok = 0, dev = 0;
-			     dev < CONFIG_SYS_IDE_MAXDEVICE;
-			     ++dev) {
-				if (ide_dev_desc[dev].part_type !=
-				    PART_TYPE_UNKNOWN) {
-					++ok;
-					if (dev)
-						putc('\n');
-					part_print(&ide_dev_desc[dev]);
-				}
-			}
-			if (!ok) {
-				puts("\nno IDE devices available\n");
-				rcode++;
-			}
-			return rcode;
+			if (blk_list_part(IF_TYPE_IDE))
+				printf("\nno IDE devices available\n");
+			return 1;
 		}
 		return CMD_RET_USAGE;
 	case 3:
 		if (strncmp(argv[1], "dev", 3) == 0) {
 			int dev = (int)simple_strtoul(argv[2], NULL, 10);
 
-			printf("\nIDE device %d: ", dev);
-			if (dev >= CONFIG_SYS_IDE_MAXDEVICE) {
-				puts("unknown device\n");
-				return 1;
+			if (!blk_show_device(IF_TYPE_IDE, dev)) {
+				curr_device = dev;
+				printf("... is now current device\n");
+			} else {
+				return CMD_RET_FAILURE;
 			}
-			dev_print(&ide_dev_desc[dev]);
-			/*ide_print (dev); */
-
-			if (ide_dev_desc[dev].type == DEV_TYPE_UNKNOWN)
-				return 1;
-
-			curr_device = dev;
-
-			puts("... is now current device\n");
-
 			return 0;
 		} else if (strncmp(argv[1], "part", 4) == 0) {
 			int dev = (int)simple_strtoul(argv[2], NULL, 10);
 
-			if (ide_dev_desc[dev].part_type != PART_TYPE_UNKNOWN) {
-				part_print(&ide_dev_desc[dev]);
-			} else {
-				printf("\nIDE device %d not available\n",
-				       dev);
-				rcode = 1;
+			if (blk_print_part_devnum(IF_TYPE_IDE, dev)) {
+				printf("\nIDE device %d not available\n", dev);
+				return CMD_RET_FAILURE;
 			}
-			return rcode;
+			return 1;
 		}
 
 		return CMD_RET_USAGE;
@@ -841,7 +95,6 @@
 		if (strcmp(argv[1], "read") == 0) {
 			ulong addr = simple_strtoul(argv[2], NULL, 16);
 			ulong cnt = simple_strtoul(argv[4], NULL, 16);
-			struct blk_desc *dev_desc;
 			ulong n;
 
 #ifdef CONFIG_SYS_64BIT_LBA
@@ -856,11 +109,8 @@
 			       curr_device, blk, cnt);
 #endif
 
-			dev_desc = &ide_dev_desc[curr_device];
-			n = blk_dread(dev_desc, blk, cnt, (ulong *)addr);
-			/* flush cache after read */
-			flush_cache(addr,
-				    cnt * ide_dev_desc[curr_device].blksz);
+			n = blk_read_devnum(IF_TYPE_IDE, curr_device, blk, cnt,
+					    (ulong *)addr);
 
 			printf("%ld blocks read: %s\n",
 			       n, (n == cnt) ? "OK" : "ERROR");
@@ -884,8 +134,8 @@
 			printf("\nIDE write: device %d block # %ld, count %ld...",
 			       curr_device, blk, cnt);
 #endif
-			n = ide_write(&ide_dev_desc[curr_device], blk, cnt,
-				      (ulong *)addr);
+			n = blk_write_devnum(IF_TYPE_IDE, curr_device, blk, cnt,
+					     (ulong *)addr);
 
 			printf("%ld blocks written: %s\n", n,
 			       n == cnt ? "OK" : "ERROR");
@@ -906,511 +156,6 @@
 	return common_diskboot(cmdtp, "ide", argc, argv);
 }
 
-/* ------------------------------------------------------------------------- */
-
-__weak void ide_led(uchar led, uchar status)
-{
-#if defined(CONFIG_IDE_LED) && defined(PER8_BASE) /* required by LED_PORT */
-	static uchar led_buffer;	/* Buffer for current LED status */
-
-	uchar *led_port = LED_PORT;
-
-	if (status)		/* switch LED on        */
-		led_buffer |= led;
-	else			/* switch LED off       */
-		led_buffer &= ~led;
-
-	*led_port = led_buffer;
-#endif
-}
-
-/* ------------------------------------------------------------------------- */
-
-__weak void ide_outb(int dev, int port, unsigned char val)
-{
-	debug("ide_outb (dev= %d, port= 0x%x, val= 0x%02x) : @ 0x%08lx\n",
-	      dev, port, val,
-	      (ATA_CURR_BASE(dev) + CONFIG_SYS_ATA_PORT_ADDR(port)));
-
-#if defined(CONFIG_IDE_AHB)
-	if (port) {
-		/* write command */
-		ide_write_register(dev, port, val);
-	} else {
-		/* write data */
-		outb(val, (ATA_CURR_BASE(dev)));
-	}
-#else
-	outb(val, (ATA_CURR_BASE(dev) + CONFIG_SYS_ATA_PORT_ADDR(port)));
-#endif
-}
-
-__weak unsigned char ide_inb(int dev, int port)
-{
-	uchar val;
-
-#if defined(CONFIG_IDE_AHB)
-	val = ide_read_register(dev, port);
-#else
-	val = inb((ATA_CURR_BASE(dev) + CONFIG_SYS_ATA_PORT_ADDR(port)));
-#endif
-
-	debug("ide_inb (dev= %d, port= 0x%x) : @ 0x%08lx -> 0x%02x\n",
-	      dev, port,
-	      (ATA_CURR_BASE(dev) + CONFIG_SYS_ATA_PORT_ADDR(port)), val);
-	return val;
-}
-
-void ide_init(void)
-{
-	unsigned char c;
-	int i, bus;
-
-#ifdef CONFIG_IDE_8xx_PCCARD
-	extern int ide_devices_found;	/* Initialized in check_ide_device() */
-#endif /* CONFIG_IDE_8xx_PCCARD */
-
-#ifdef CONFIG_IDE_PREINIT
-	WATCHDOG_RESET();
-
-	if (ide_preinit()) {
-		puts("ide_preinit failed\n");
-		return;
-	}
-#endif /* CONFIG_IDE_PREINIT */
-
-	WATCHDOG_RESET();
-
-	/*
-	 * Reset the IDE just to be sure.
-	 * Light LED's to show
-	 */
-	ide_led((LED_IDE1 | LED_IDE2), 1);	/* LED's on     */
-
-	/* ATAPI Drives seems to need a proper IDE Reset */
-	ide_reset();
-
-#ifdef CONFIG_IDE_INIT_POSTRESET
-	WATCHDOG_RESET();
-
-	if (ide_init_postreset()) {
-		puts("ide_preinit_postreset failed\n");
-		return;
-	}
-#endif /* CONFIG_IDE_INIT_POSTRESET */
-
-	/*
-	 * Wait for IDE to get ready.
-	 * According to spec, this can take up to 31 seconds!
-	 */
-	for (bus = 0; bus < CONFIG_SYS_IDE_MAXBUS; ++bus) {
-		int dev =
-			bus * (CONFIG_SYS_IDE_MAXDEVICE /
-			       CONFIG_SYS_IDE_MAXBUS);
-
-#ifdef CONFIG_IDE_8xx_PCCARD
-		/* Skip non-ide devices from probing */
-		if ((ide_devices_found & (1 << bus)) == 0) {
-			ide_led((LED_IDE1 | LED_IDE2), 0);	/* LED's off */
-			continue;
-		}
-#endif
-		printf("Bus %d: ", bus);
-
-		ide_bus_ok[bus] = 0;
-
-		/* Select device
-		 */
-		udelay(100000);	/* 100 ms */
-		ide_outb(dev, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(dev));
-		udelay(100000);	/* 100 ms */
-		i = 0;
-		do {
-			udelay(10000);	/* 10 ms */
-
-			c = ide_inb(dev, ATA_STATUS);
-			i++;
-			if (i > (ATA_RESET_TIME * 100)) {
-				puts("** Timeout **\n");
-				/* LED's off */
-				ide_led((LED_IDE1 | LED_IDE2), 0);
-				return;
-			}
-			if ((i >= 100) && ((i % 100) == 0))
-				putc('.');
-
-		} while (c & ATA_STAT_BUSY);
-
-		if (c & (ATA_STAT_BUSY | ATA_STAT_FAULT)) {
-			puts("not available  ");
-			debug("Status = 0x%02X ", c);
-#ifndef CONFIG_ATAPI		/* ATAPI Devices do not set DRDY */
-		} else if ((c & ATA_STAT_READY) == 0) {
-			puts("not available  ");
-			debug("Status = 0x%02X ", c);
-#endif
-		} else {
-			puts("OK ");
-			ide_bus_ok[bus] = 1;
-		}
-		WATCHDOG_RESET();
-	}
-
-	putc('\n');
-
-	ide_led((LED_IDE1 | LED_IDE2), 0);	/* LED's off    */
-
-	curr_device = -1;
-	for (i = 0; i < CONFIG_SYS_IDE_MAXDEVICE; ++i) {
-		int led = (IDE_BUS(i) == 0) ? LED_IDE1 : LED_IDE2;
-		ide_dev_desc[i].type = DEV_TYPE_UNKNOWN;
-		ide_dev_desc[i].if_type = IF_TYPE_IDE;
-		ide_dev_desc[i].devnum = i;
-		ide_dev_desc[i].part_type = PART_TYPE_UNKNOWN;
-		ide_dev_desc[i].blksz = 0;
-		ide_dev_desc[i].log2blksz =
-			LOG2_INVALID(typeof(ide_dev_desc[i].log2blksz));
-		ide_dev_desc[i].lba = 0;
-		ide_dev_desc[i].block_read = ide_read;
-		ide_dev_desc[i].block_write = ide_write;
-		if (!ide_bus_ok[IDE_BUS(i)])
-			continue;
-		ide_led(led, 1);	/* LED on       */
-		ide_ident(&ide_dev_desc[i]);
-		ide_led(led, 0);	/* LED off      */
-		dev_print(&ide_dev_desc[i]);
-
-		if ((ide_dev_desc[i].lba > 0) && (ide_dev_desc[i].blksz > 0)) {
-			/* initialize partition type */
-			part_init(&ide_dev_desc[i]);
-			if (curr_device < 0)
-				curr_device = i;
-		}
-	}
-	WATCHDOG_RESET();
-}
-
-/* ------------------------------------------------------------------------- */
-
-#ifdef CONFIG_PARTITIONS
-struct blk_desc *ide_get_dev(int dev)
-{
-	return (dev < CONFIG_SYS_IDE_MAXDEVICE) ? &ide_dev_desc[dev] : NULL;
-}
-#endif
-
-/* ------------------------------------------------------------------------- */
-
-/* We only need to swap data if we are running on a big endian cpu. */
-#if defined(__LITTLE_ENDIAN)
-__weak void ide_input_swap_data(int dev, ulong *sect_buf, int words)
-{
-	ide_input_data(dev, sect_buf, words);
-}
-#else
-__weak void ide_input_swap_data(int dev, ulong *sect_buf, int words)
-{
-	volatile ushort *pbuf =
-		(ushort *)(ATA_CURR_BASE(dev) + ATA_DATA_REG);
-	ushort *dbuf = (ushort *)sect_buf;
-
-	debug("in input swap data base for read is %lx\n",
-	      (unsigned long) pbuf);
-
-	while (words--) {
-#ifdef __MIPS__
-		*dbuf++ = swab16p((u16 *)pbuf);
-		*dbuf++ = swab16p((u16 *)pbuf);
-#else
-		*dbuf++ = ld_le16(pbuf);
-		*dbuf++ = ld_le16(pbuf);
-#endif /* !MIPS */
-	}
-}
-#endif /* __LITTLE_ENDIAN */
-
-
-#if defined(CONFIG_IDE_SWAP_IO)
-__weak void ide_output_data(int dev, const ulong *sect_buf, int words)
-{
-	ushort *dbuf;
-	volatile ushort *pbuf;
-
-	pbuf = (ushort *)(ATA_CURR_BASE(dev) + ATA_DATA_REG);
-	dbuf = (ushort *)sect_buf;
-	while (words--) {
-		EIEIO;
-		*pbuf = *dbuf++;
-		EIEIO;
-		*pbuf = *dbuf++;
-	}
-}
-#else  /* ! CONFIG_IDE_SWAP_IO */
-__weak void ide_output_data(int dev, const ulong *sect_buf, int words)
-{
-#if defined(CONFIG_IDE_AHB)
-	ide_write_data(dev, sect_buf, words);
-#else
-	outsw(ATA_CURR_BASE(dev) + ATA_DATA_REG, sect_buf, words << 1);
-#endif
-}
-#endif /* CONFIG_IDE_SWAP_IO */
-
-#if defined(CONFIG_IDE_SWAP_IO)
-__weak void ide_input_data(int dev, ulong *sect_buf, int words)
-{
-	ushort *dbuf;
-	volatile ushort *pbuf;
-
-	pbuf = (ushort *)(ATA_CURR_BASE(dev) + ATA_DATA_REG);
-	dbuf = (ushort *)sect_buf;
-
-	debug("in input data base for read is %lx\n", (unsigned long) pbuf);
-
-	while (words--) {
-		EIEIO;
-		*dbuf++ = *pbuf;
-		EIEIO;
-		*dbuf++ = *pbuf;
-	}
-}
-#else  /* ! CONFIG_IDE_SWAP_IO */
-__weak void ide_input_data(int dev, ulong *sect_buf, int words)
-{
-#if defined(CONFIG_IDE_AHB)
-	ide_read_data(dev, sect_buf, words);
-#else
-	insw(ATA_CURR_BASE(dev) + ATA_DATA_REG, sect_buf, words << 1);
-#endif
-}
-
-#endif /* CONFIG_IDE_SWAP_IO */
-
-/* ------------------------------------------------------------------------- */
-
-ulong ide_read(struct blk_desc *block_dev, lbaint_t blknr, lbaint_t blkcnt,
-	       void *buffer)
-{
-	int device = block_dev->devnum;
-	ulong n = 0;
-	unsigned char c;
-	unsigned char pwrsave = 0;	/* power save */
-
-#ifdef CONFIG_LBA48
-	unsigned char lba48 = 0;
-
-	if (blknr & 0x0000fffff0000000ULL) {
-		/* more than 28 bits used, use 48bit mode */
-		lba48 = 1;
-	}
-#endif
-	debug("ide_read dev %d start " LBAF ", blocks " LBAF " buffer at %lX\n",
-	      device, blknr, blkcnt, (ulong) buffer);
-
-	ide_led(DEVICE_LED(device), 1);	/* LED on       */
-
-	/* Select device
-	 */
-	ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
-	c = ide_wait(device, IDE_TIME_OUT);
-
-	if (c & ATA_STAT_BUSY) {
-		printf("IDE read: device %d not ready\n", device);
-		goto IDE_READ_E;
-	}
-
-	/* first check if the drive is in Powersaving mode, if yes,
-	 * increase the timeout value */
-	ide_outb(device, ATA_COMMAND, ATA_CMD_CHK_PWR);
-	udelay(50);
-
-	c = ide_wait(device, IDE_TIME_OUT);	/* can't take over 500 ms */
-
-	if (c & ATA_STAT_BUSY) {
-		printf("IDE read: device %d not ready\n", device);
-		goto IDE_READ_E;
-	}
-	if ((c & ATA_STAT_ERR) == ATA_STAT_ERR) {
-		printf("No Powersaving mode %X\n", c);
-	} else {
-		c = ide_inb(device, ATA_SECT_CNT);
-		debug("Powersaving %02X\n", c);
-		if (c == 0)
-			pwrsave = 1;
-	}
-
-
-	while (blkcnt-- > 0) {
-
-		c = ide_wait(device, IDE_TIME_OUT);
-
-		if (c & ATA_STAT_BUSY) {
-			printf("IDE read: device %d not ready\n", device);
-			break;
-		}
-#ifdef CONFIG_LBA48
-		if (lba48) {
-			/* write high bits */
-			ide_outb(device, ATA_SECT_CNT, 0);
-			ide_outb(device, ATA_LBA_LOW, (blknr >> 24) & 0xFF);
-#ifdef CONFIG_SYS_64BIT_LBA
-			ide_outb(device, ATA_LBA_MID, (blknr >> 32) & 0xFF);
-			ide_outb(device, ATA_LBA_HIGH, (blknr >> 40) & 0xFF);
-#else
-			ide_outb(device, ATA_LBA_MID, 0);
-			ide_outb(device, ATA_LBA_HIGH, 0);
-#endif
-		}
-#endif
-		ide_outb(device, ATA_SECT_CNT, 1);
-		ide_outb(device, ATA_LBA_LOW, (blknr >> 0) & 0xFF);
-		ide_outb(device, ATA_LBA_MID, (blknr >> 8) & 0xFF);
-		ide_outb(device, ATA_LBA_HIGH, (blknr >> 16) & 0xFF);
-
-#ifdef CONFIG_LBA48
-		if (lba48) {
-			ide_outb(device, ATA_DEV_HD,
-				 ATA_LBA | ATA_DEVICE(device));
-			ide_outb(device, ATA_COMMAND, ATA_CMD_READ_EXT);
-
-		} else
-#endif
-		{
-			ide_outb(device, ATA_DEV_HD, ATA_LBA |
-				 ATA_DEVICE(device) | ((blknr >> 24) & 0xF));
-			ide_outb(device, ATA_COMMAND, ATA_CMD_READ);
-		}
-
-		udelay(50);
-
-		if (pwrsave) {
-			/* may take up to 4 sec */
-			c = ide_wait(device, IDE_SPIN_UP_TIME_OUT);
-			pwrsave = 0;
-		} else {
-			/* can't take over 500 ms */
-			c = ide_wait(device, IDE_TIME_OUT);
-		}
-
-		if ((c & (ATA_STAT_DRQ | ATA_STAT_BUSY | ATA_STAT_ERR)) !=
-		    ATA_STAT_DRQ) {
-			printf("Error (no IRQ) dev %d blk " LBAF
-			       ": status %#02x\n", device, blknr, c);
-			break;
-		}
-
-		ide_input_data(device, buffer, ATA_SECTORWORDS);
-		(void) ide_inb(device, ATA_STATUS);	/* clear IRQ */
-
-		++n;
-		++blknr;
-		buffer += ATA_BLOCKSIZE;
-	}
-IDE_READ_E:
-	ide_led(DEVICE_LED(device), 0);	/* LED off      */
-	return n;
-}
-
-/* ------------------------------------------------------------------------- */
-
-
-ulong ide_write(struct blk_desc *block_dev, lbaint_t blknr, lbaint_t blkcnt,
-		const void *buffer)
-{
-	int device = block_dev->devnum;
-	ulong n = 0;
-	unsigned char c;
-
-#ifdef CONFIG_LBA48
-	unsigned char lba48 = 0;
-
-	if (blknr & 0x0000fffff0000000ULL) {
-		/* more than 28 bits used, use 48bit mode */
-		lba48 = 1;
-	}
-#endif
-
-	ide_led(DEVICE_LED(device), 1);	/* LED on       */
-
-	/* Select device
-	 */
-	ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
-
-	while (blkcnt-- > 0) {
-		c = ide_wait(device, IDE_TIME_OUT);
-
-		if (c & ATA_STAT_BUSY) {
-			printf("IDE read: device %d not ready\n", device);
-			goto WR_OUT;
-		}
-#ifdef CONFIG_LBA48
-		if (lba48) {
-			/* write high bits */
-			ide_outb(device, ATA_SECT_CNT, 0);
-			ide_outb(device, ATA_LBA_LOW, (blknr >> 24) & 0xFF);
-#ifdef CONFIG_SYS_64BIT_LBA
-			ide_outb(device, ATA_LBA_MID, (blknr >> 32) & 0xFF);
-			ide_outb(device, ATA_LBA_HIGH, (blknr >> 40) & 0xFF);
-#else
-			ide_outb(device, ATA_LBA_MID, 0);
-			ide_outb(device, ATA_LBA_HIGH, 0);
-#endif
-		}
-#endif
-		ide_outb(device, ATA_SECT_CNT, 1);
-		ide_outb(device, ATA_LBA_LOW, (blknr >> 0) & 0xFF);
-		ide_outb(device, ATA_LBA_MID, (blknr >> 8) & 0xFF);
-		ide_outb(device, ATA_LBA_HIGH, (blknr >> 16) & 0xFF);
-
-#ifdef CONFIG_LBA48
-		if (lba48) {
-			ide_outb(device, ATA_DEV_HD,
-				 ATA_LBA | ATA_DEVICE(device));
-			ide_outb(device, ATA_COMMAND, ATA_CMD_WRITE_EXT);
-
-		} else
-#endif
-		{
-			ide_outb(device, ATA_DEV_HD, ATA_LBA |
-				 ATA_DEVICE(device) | ((blknr >> 24) & 0xF));
-			ide_outb(device, ATA_COMMAND, ATA_CMD_WRITE);
-		}
-
-		udelay(50);
-
-		/* can't take over 500 ms */
-		c = ide_wait(device, IDE_TIME_OUT);
-
-		if ((c & (ATA_STAT_DRQ | ATA_STAT_BUSY | ATA_STAT_ERR)) !=
-		    ATA_STAT_DRQ) {
-			printf("Error (no IRQ) dev %d blk " LBAF
-			       ": status %#02x\n", device, blknr, c);
-			goto WR_OUT;
-		}
-
-		ide_output_data(device, buffer, ATA_SECTORWORDS);
-		c = ide_inb(device, ATA_STATUS);	/* clear IRQ */
-		++n;
-		++blknr;
-		buffer += ATA_BLOCKSIZE;
-	}
-WR_OUT:
-	ide_led(DEVICE_LED(device), 0);	/* LED off      */
-	return n;
-}
-
-/* ------------------------------------------------------------------------- */
-
-#if defined(CONFIG_OF_IDE_FIXUP)
-int ide_device_present(int dev)
-{
-	if (dev >= CONFIG_SYS_IDE_MAXBUS)
-		return 0;
-	return ide_dev_desc[dev].type == DEV_TYPE_UNKNOWN ? 0 : 1;
-}
-#endif
-/* ------------------------------------------------------------------------- */
-
 U_BOOT_CMD(ide, 5, 1, do_ide,
 	   "IDE sub-system",
 	   "reset - reset IDE controller\n"