| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * NVIDIA Tegra20 GPIO handling. |
| * (C) Copyright 2010-2012,2015 |
| * NVIDIA Corporation <www.nvidia.com> |
| */ |
| |
| /* |
| * Based on (mostly copied from) kw_gpio.c based Linux 2.6 kernel driver. |
| * Tom Warren (twarren@nvidia.com) |
| */ |
| |
| #include <dm.h> |
| #include <log.h> |
| #include <malloc.h> |
| #include <errno.h> |
| #include <fdtdec.h> |
| #include <asm/io.h> |
| #include <asm/bitops.h> |
| #include <asm/arch/tegra.h> |
| #include <asm/gpio.h> |
| #include <dm/device-internal.h> |
| #include <dt-bindings/gpio/gpio.h> |
| |
| static const int CFG_SFIO = 0; |
| static const int CFG_GPIO = 1; |
| static const int DIRECTION_INPUT = 0; |
| static const int DIRECTION_OUTPUT = 1; |
| |
| struct tegra_gpio_plat { |
| struct gpio_ctlr_bank *bank; |
| const char *port_name; /* Name of port, e.g. "B" */ |
| int base_gpio; /* Port number for this port (0, 1,.., n-1) */ |
| }; |
| |
| /* Information about each port at run-time */ |
| struct tegra_port_info { |
| struct gpio_ctlr_bank *bank; |
| int base_gpio; /* Port number for this port (0, 1,.., n-1) */ |
| }; |
| |
| /* Return config of pin 'gpio' as GPIO (1) or SFIO (0) */ |
| static int get_config(unsigned gpio) |
| { |
| struct gpio_ctlr *ctlr = (struct gpio_ctlr *)NV_PA_GPIO_BASE; |
| struct gpio_ctlr_bank *bank = &ctlr->gpio_bank[GPIO_BANK(gpio)]; |
| u32 u; |
| int type; |
| |
| u = readl(&bank->gpio_config[GPIO_PORT(gpio)]); |
| type = (u >> GPIO_BIT(gpio)) & 1; |
| |
| debug("get_config: port = %d, bit = %d is %s\n", |
| GPIO_FULLPORT(gpio), GPIO_BIT(gpio), type ? "GPIO" : "SFPIO"); |
| |
| return type ? CFG_GPIO : CFG_SFIO; |
| } |
| |
| /* Config pin 'gpio' as GPIO or SFIO, based on 'type' */ |
| static void set_config(unsigned gpio, int type) |
| { |
| struct gpio_ctlr *ctlr = (struct gpio_ctlr *)NV_PA_GPIO_BASE; |
| struct gpio_ctlr_bank *bank = &ctlr->gpio_bank[GPIO_BANK(gpio)]; |
| u32 u; |
| |
| debug("set_config: port = %d, bit = %d, %s\n", |
| GPIO_FULLPORT(gpio), GPIO_BIT(gpio), type ? "GPIO" : "SFPIO"); |
| |
| u = readl(&bank->gpio_config[GPIO_PORT(gpio)]); |
| if (type != CFG_SFIO) |
| u |= 1 << GPIO_BIT(gpio); |
| else |
| u &= ~(1 << GPIO_BIT(gpio)); |
| writel(u, &bank->gpio_config[GPIO_PORT(gpio)]); |
| } |
| |
| /* Return GPIO pin 'gpio' direction - 0 = input or 1 = output */ |
| static int get_direction(unsigned gpio) |
| { |
| struct gpio_ctlr *ctlr = (struct gpio_ctlr *)NV_PA_GPIO_BASE; |
| struct gpio_ctlr_bank *bank = &ctlr->gpio_bank[GPIO_BANK(gpio)]; |
| u32 u; |
| int dir; |
| |
| u = readl(&bank->gpio_dir_out[GPIO_PORT(gpio)]); |
| dir = (u >> GPIO_BIT(gpio)) & 1; |
| |
| debug("get_direction: port = %d, bit = %d, %s\n", |
| GPIO_FULLPORT(gpio), GPIO_BIT(gpio), dir ? "OUT" : "IN"); |
| |
| return dir ? DIRECTION_OUTPUT : DIRECTION_INPUT; |
| } |
| |
| /* Config GPIO pin 'gpio' as input or output (OE) as per 'output' */ |
| static void set_direction(unsigned gpio, int output) |
| { |
| struct gpio_ctlr *ctlr = (struct gpio_ctlr *)NV_PA_GPIO_BASE; |
| struct gpio_ctlr_bank *bank = &ctlr->gpio_bank[GPIO_BANK(gpio)]; |
| u32 u; |
| |
| debug("set_direction: port = %d, bit = %d, %s\n", |
| GPIO_FULLPORT(gpio), GPIO_BIT(gpio), output ? "OUT" : "IN"); |
| |
| u = readl(&bank->gpio_dir_out[GPIO_PORT(gpio)]); |
| if (output != DIRECTION_INPUT) |
| u |= 1 << GPIO_BIT(gpio); |
| else |
| u &= ~(1 << GPIO_BIT(gpio)); |
| writel(u, &bank->gpio_dir_out[GPIO_PORT(gpio)]); |
| } |
| |
| /* set GPIO pin 'gpio' output bit as 0 or 1 as per 'high' */ |
| static void set_level(unsigned gpio, int high) |
| { |
| struct gpio_ctlr *ctlr = (struct gpio_ctlr *)NV_PA_GPIO_BASE; |
| struct gpio_ctlr_bank *bank = &ctlr->gpio_bank[GPIO_BANK(gpio)]; |
| u32 u; |
| |
| debug("set_level: port = %d, bit %d == %d\n", |
| GPIO_FULLPORT(gpio), GPIO_BIT(gpio), high); |
| |
| u = readl(&bank->gpio_out[GPIO_PORT(gpio)]); |
| if (high) |
| u |= 1 << GPIO_BIT(gpio); |
| else |
| u &= ~(1 << GPIO_BIT(gpio)); |
| writel(u, &bank->gpio_out[GPIO_PORT(gpio)]); |
| } |
| |
| /* |
| * Generic_GPIO primitives. |
| */ |
| |
| /* set GPIO pin 'gpio' as an input */ |
| static int tegra_gpio_direction_input(struct udevice *dev, unsigned offset) |
| { |
| struct tegra_port_info *state = dev_get_priv(dev); |
| |
| /* Configure GPIO direction as input. */ |
| set_direction(state->base_gpio + offset, DIRECTION_INPUT); |
| |
| /* Enable the pin as a GPIO */ |
| set_config(state->base_gpio + offset, 1); |
| |
| return 0; |
| } |
| |
| /* set GPIO pin 'gpio' as an output, with polarity 'value' */ |
| static int tegra_gpio_direction_output(struct udevice *dev, unsigned offset, |
| int value) |
| { |
| struct tegra_port_info *state = dev_get_priv(dev); |
| int gpio = state->base_gpio + offset; |
| |
| /* Configure GPIO output value. */ |
| set_level(gpio, value); |
| |
| /* Configure GPIO direction as output. */ |
| set_direction(gpio, DIRECTION_OUTPUT); |
| |
| /* Enable the pin as a GPIO */ |
| set_config(state->base_gpio + offset, 1); |
| |
| return 0; |
| } |
| |
| /* read GPIO IN value of pin 'gpio' */ |
| static int tegra_gpio_get_value(struct udevice *dev, unsigned offset) |
| { |
| struct tegra_port_info *state = dev_get_priv(dev); |
| int gpio = state->base_gpio + offset; |
| int val; |
| |
| debug("%s: pin = %d (port %d:bit %d)\n", __func__, |
| gpio, GPIO_FULLPORT(gpio), GPIO_BIT(gpio)); |
| |
| if (get_direction(gpio) == DIRECTION_INPUT) |
| val = readl(&state->bank->gpio_in[GPIO_PORT(gpio)]); |
| else |
| val = readl(&state->bank->gpio_out[GPIO_PORT(gpio)]); |
| |
| return (val >> GPIO_BIT(gpio)) & 1; |
| } |
| |
| /* write GPIO OUT value to pin 'gpio' */ |
| static int tegra_gpio_set_value(struct udevice *dev, unsigned offset, int value) |
| { |
| struct tegra_port_info *state = dev_get_priv(dev); |
| int gpio = state->base_gpio + offset; |
| |
| debug("gpio_set_value: pin = %d (port %d:bit %d), value = %d\n", |
| gpio, GPIO_FULLPORT(gpio), GPIO_BIT(gpio), value); |
| |
| /* Configure GPIO output value. */ |
| set_level(gpio, value); |
| |
| return 0; |
| } |
| |
| void gpio_config_table(const struct tegra_gpio_config *config, int len) |
| { |
| int i; |
| |
| for (i = 0; i < len; i++) { |
| switch (config[i].init) { |
| case TEGRA_GPIO_INIT_IN: |
| set_direction(config[i].gpio, DIRECTION_INPUT); |
| break; |
| case TEGRA_GPIO_INIT_OUT0: |
| set_level(config[i].gpio, 0); |
| set_direction(config[i].gpio, DIRECTION_OUTPUT); |
| break; |
| case TEGRA_GPIO_INIT_OUT1: |
| set_level(config[i].gpio, 1); |
| set_direction(config[i].gpio, DIRECTION_OUTPUT); |
| break; |
| } |
| set_config(config[i].gpio, CFG_GPIO); |
| } |
| } |
| |
| static int tegra_gpio_get_function(struct udevice *dev, unsigned offset) |
| { |
| struct tegra_port_info *state = dev_get_priv(dev); |
| int gpio = state->base_gpio + offset; |
| |
| if (!get_config(gpio)) |
| return GPIOF_FUNC; |
| else if (get_direction(gpio)) |
| return GPIOF_OUTPUT; |
| else |
| return GPIOF_INPUT; |
| } |
| |
| static int tegra_gpio_xlate(struct udevice *dev, struct gpio_desc *desc, |
| struct ofnode_phandle_args *args) |
| { |
| int gpio, port, ret; |
| |
| gpio = args->args[0]; |
| port = gpio / TEGRA_GPIOS_PER_PORT; |
| ret = device_get_child(dev, port, &desc->dev); |
| if (ret) |
| return ret; |
| desc->offset = gpio % TEGRA_GPIOS_PER_PORT; |
| desc->flags = args->args[1] & GPIO_ACTIVE_LOW ? GPIOD_ACTIVE_LOW : 0; |
| |
| return 0; |
| } |
| |
| static const struct dm_gpio_ops gpio_tegra_ops = { |
| .direction_input = tegra_gpio_direction_input, |
| .direction_output = tegra_gpio_direction_output, |
| .get_value = tegra_gpio_get_value, |
| .set_value = tegra_gpio_set_value, |
| .get_function = tegra_gpio_get_function, |
| .xlate = tegra_gpio_xlate, |
| }; |
| |
| /* |
| * SPL GPIO functions. |
| */ |
| int spl_gpio_output(void *regs, uint gpio, int value) |
| { |
| /* Configure GPIO output value. */ |
| set_level(gpio, value); |
| |
| /* Configure GPIO direction as output. */ |
| set_direction(gpio, DIRECTION_OUTPUT); |
| |
| /* Enable the pin as a GPIO */ |
| set_config(gpio, 1); |
| |
| return 0; |
| } |
| |
| int spl_gpio_input(void *regs, uint gpio) |
| { |
| /* Configure GPIO direction as input. */ |
| set_direction(gpio, DIRECTION_INPUT); |
| |
| /* Enable the pin as a GPIO */ |
| set_config(gpio, 1); |
| |
| return 0; |
| } |
| |
| int spl_gpio_get_value(void *regs, uint gpio) |
| { |
| struct gpio_ctlr *ctlr = (struct gpio_ctlr *)NV_PA_GPIO_BASE; |
| struct gpio_ctlr_bank *bank = &ctlr->gpio_bank[GPIO_BANK(gpio)]; |
| int val; |
| |
| if (get_direction(gpio) == DIRECTION_INPUT) |
| val = readl(&bank->gpio_in[GPIO_PORT(gpio)]); |
| else |
| val = readl(&bank->gpio_out[GPIO_PORT(gpio)]); |
| |
| return (val >> GPIO_BIT(gpio)) & 1; |
| } |
| |
| int spl_gpio_set_value(void *regs, uint gpio, int value) |
| { |
| /* Configure GPIO output value. */ |
| set_level(gpio, value); |
| |
| return 0; |
| } |
| |
| /** |
| * Returns the name of a GPIO port |
| * |
| * GPIOs are named A, B, C, ..., Z, AA, BB, CC, ... |
| * |
| * @base_port: Base port number (0, 1..n-1) |
| * Return: allocated string containing the name |
| */ |
| static char *gpio_port_name(int base_port) |
| { |
| char *name, *s; |
| |
| name = malloc(3); |
| if (name) { |
| s = name; |
| *s++ = 'A' + (base_port % 26); |
| if (base_port >= 26) |
| *s++ = *name; |
| *s = '\0'; |
| } |
| |
| return name; |
| } |
| |
| static const struct udevice_id tegra_gpio_ids[] = { |
| { .compatible = "nvidia,tegra30-gpio" }, |
| { .compatible = "nvidia,tegra20-gpio" }, |
| { } |
| }; |
| |
| static int gpio_tegra_probe(struct udevice *dev) |
| { |
| struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev); |
| struct tegra_port_info *priv = dev_get_priv(dev); |
| struct tegra_gpio_plat *plat = dev_get_plat(dev); |
| |
| /* Only child devices have ports */ |
| if (!plat) |
| return 0; |
| |
| priv->bank = plat->bank; |
| priv->base_gpio = plat->base_gpio; |
| |
| uc_priv->gpio_count = TEGRA_GPIOS_PER_PORT; |
| uc_priv->bank_name = plat->port_name; |
| |
| return 0; |
| } |
| |
| /** |
| * We have a top-level GPIO device with no actual GPIOs. It has a child |
| * device for each Tegra port. |
| */ |
| static int gpio_tegra_bind(struct udevice *parent) |
| { |
| struct tegra_gpio_plat *plat = dev_get_plat(parent); |
| struct gpio_ctlr *ctlr; |
| int bank_count; |
| int bank; |
| int ret; |
| |
| /* If this is a child device, there is nothing to do here */ |
| if (plat) |
| return 0; |
| |
| /* TODO(sjg@chromium.org): Remove once SPL supports device tree */ |
| #ifdef CONFIG_XPL_BUILD |
| ctlr = (struct gpio_ctlr *)NV_PA_GPIO_BASE; |
| bank_count = TEGRA_GPIO_BANKS; |
| #else |
| { |
| int len; |
| |
| /* |
| * This driver does not make use of interrupts, other than to figure |
| * out the number of GPIO banks |
| */ |
| len = dev_read_size(parent, "interrupts"); |
| if (len < 0) |
| return len; |
| bank_count = len / 3 / sizeof(u32); |
| ctlr = dev_read_addr_ptr(parent); |
| if (!ctlr) |
| return -EINVAL; |
| } |
| #endif |
| for (bank = 0; bank < bank_count; bank++) { |
| int port; |
| |
| for (port = 0; port < TEGRA_PORTS_PER_BANK; port++) { |
| struct tegra_gpio_plat *plat; |
| struct udevice *dev; |
| int base_port; |
| |
| plat = calloc(1, sizeof(*plat)); |
| if (!plat) |
| return -ENOMEM; |
| plat->bank = &ctlr->gpio_bank[bank]; |
| base_port = bank * TEGRA_PORTS_PER_BANK + port; |
| plat->base_gpio = TEGRA_GPIOS_PER_PORT * base_port; |
| plat->port_name = gpio_port_name(base_port); |
| |
| ret = device_bind(parent, parent->driver, |
| plat->port_name, plat, |
| dev_ofnode(parent), &dev); |
| if (ret) |
| return ret; |
| } |
| } |
| |
| return 0; |
| } |
| |
| U_BOOT_DRIVER(gpio_tegra) = { |
| .name = "gpio_tegra", |
| .id = UCLASS_GPIO, |
| .of_match = tegra_gpio_ids, |
| .bind = gpio_tegra_bind, |
| .probe = gpio_tegra_probe, |
| .priv_auto = sizeof(struct tegra_port_info), |
| .ops = &gpio_tegra_ops, |
| }; |