PowerPC: keymile: Add support for kmcent2 board
Add basic support for the Hitachi Power Grids kmcent2 board, based
on the NXP QorIQ T1040 SoC.
Signed-off-by: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
[Fixed blank line at EOF errors]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
diff --git a/board/keymile/kmcent2/ddr.c b/board/keymile/kmcent2/ddr.c
new file mode 100644
index 0000000..4f77820
--- /dev/null
+++ b/board/keymile/kmcent2/ddr.c
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2016 Keymile AG
+ * Rainer Boschung <rainer.boschung@keymile.com>
+ *
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ */
+
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+#include <asm/mpc85xx_gpio.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#include <hwconfig.h>
+#include <i2c.h>
+#include <init.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define DQSn_POS(n) (3 - (((n) - 1) % 4)) * 8
+#define DQSn_START(n, start) ((start) << DQSn_POS(n))
+
+void fsl_ddr_board_options(memctl_options_t *popts, dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ if (ctrl_num > 1) {
+ printf("Not supported controller number %d\n", ctrl_num);
+ return;
+ }
+
+ /* 1/2 clk delay between wr command and data strobe */
+ popts->write_data_delay = 4;
+ /* clk lauched 1/2 applied cylcle after address command */
+ popts->clk_adjust = 4;
+ /* 1T timing: command/address held for only 1 cycle */
+ popts->twot_en = 0;
+ popts->threet_en = 0;
+
+ /* optimize cpo for erratum A-009942 */
+ popts->cpo_sample = 0x3b;
+
+ /* we have only one module, half str should be OK */
+ popts->half_strength_driver_enable = 1;
+ /*
+ * Write leveling override
+ */
+ /* set for DDR3-1600 */
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xf;
+ popts->wrlvl_start = 0x7;
+ /* DQS write leveling start time according layout */
+ popts->wrlvl_ctl_2 = (DQSn_START(1, 0x06) |
+ DQSn_START(2, 0x06) |
+ DQSn_START(3, 0x07) |
+ DQSn_START(4, 0x07));
+ popts->wrlvl_ctl_3 = (DQSn_START(5, 0x07) |
+ DQSn_START(6, 0x08) |
+ DQSn_START(7, 0x08) |
+ DQSn_START(8, 0x08));
+
+ /*
+ * rtt and wtt_wr override
+ */
+ popts->rtt_override = 0;
+
+ /* Enable ZQ calibration */
+ popts->zq_en = 1;
+
+ /* DHC_EN =1, ODT = 75 Ohm */
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
+ popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
+}
+
+int dram_init(void)
+{
+ phys_size_t dram_size;
+
+ puts("Initializing....using SPD\n");
+
+ dram_size = fsl_ddr_sdram();
+
+ dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+ dram_size *= 0x100000;
+
+ gd->ram_size = dram_size;
+
+ return 0;
+}