diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 6b11c3a..eb0f5bc 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1776,6 +1776,21 @@
 	help
 	  Support for Kontron SMARC-sAL28 board.
 
+config TARGET_TEN64
+	bool "Support ten64"
+	select ARCH_LS1088A
+	select ARCH_MISC_INIT
+	select ARM64
+	select ARMV8_MULTIENTRY
+	select ARCH_SUPPORT_TFABOOT
+	select BOARD_LATE_INIT
+	select SUPPORT_SPL
+	select FSL_DDR_INTERACTIVE if !SD_BOOT
+	select GPIO_EXTRA_HEADER
+	help
+	  Support for Traverse Technologies Ten64 board, based
+	  on NXP LS1088A.
+
 config TARGET_COLIBRI_PXA270
 	bool "Support colibri_pxa270"
 	select CPU_PXA27X
@@ -2225,6 +2240,7 @@
 source "board/st/stv0991/Kconfig"
 source "board/tcl/sl50/Kconfig"
 source "board/toradex/colibri_pxa270/Kconfig"
+source "board/traverse/ten64/Kconfig"
 source "board/variscite/dart_6ul/Kconfig"
 source "board/vscom/baltos/Kconfig"
 source "board/phytium/durian/Kconfig"
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 5d45d19..0ed8de2 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -485,6 +485,8 @@
 	fsl-ls1028a-kontron-sl28-var3.dtb \
 	fsl-ls1028a-kontron-sl28-var4.dtb \
 
+dtb-$(CONFIG_TARGET_TEN64) += fsl-ls1088a-ten64.dtb
+
 dtb-$(CONFIG_TARGET_DRAGONBOARD410C) += dragonboard410c.dtb
 dtb-$(CONFIG_TARGET_DRAGONBOARD820C) += dragonboard820c.dtb
 dtb-$(CONFIG_TARGET_STARQLTECHN) += starqltechn.dtb
diff --git a/arch/arm/dts/fsl-ls1028a-qds-1xxx-sch-30842.dtsi b/arch/arm/dts/fsl-ls1028a-qds-1xxx-sch-30842.dtsi
index f4c557e..f208a02 100644
--- a/arch/arm/dts/fsl-ls1028a-qds-1xxx-sch-30842.dtsi
+++ b/arch/arm/dts/fsl-ls1028a-qds-1xxx-sch-30842.dtsi
@@ -15,6 +15,7 @@
 
 &enetc_port0 {
 	status = "okay";
+	managed = "in-band-status";
 	phy-mode = "usxgmii";
 	phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@02}>;
 };
diff --git a/arch/arm/dts/fsl-ls1028a-qds-8xxx-sch-24801.dtsi b/arch/arm/dts/fsl-ls1028a-qds-8xxx-sch-24801.dtsi
index 7d197c3..0a09264 100644
--- a/arch/arm/dts/fsl-ls1028a-qds-8xxx-sch-24801.dtsi
+++ b/arch/arm/dts/fsl-ls1028a-qds-8xxx-sch-24801.dtsi
@@ -14,6 +14,7 @@
 
 &enetc_port0 {
 	status = "okay";
+	managed = "in-band-status";
 	phy-mode = "sgmii";
 	phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1c}>;
 };
diff --git a/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801-LBRW.dtsi b/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801-LBRW.dtsi
index 992092e..94b5e76 100644
--- a/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801-LBRW.dtsi
+++ b/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801-LBRW.dtsi
@@ -44,24 +44,28 @@
 
 &mscc_felix_port0 {
 	status = "okay";
+	managed = "in-band-status";
 	phy-mode = "sgmii";
 	phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1c}>;
 };
 
 &mscc_felix_port1 {
 	status = "okay";
+	managed = "in-band-status";
 	phy-mode = "sgmii";
 	phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@1c}>;
 };
 
 &mscc_felix_port2 {
 	status = "okay";
+	managed = "in-band-status";
 	phy-mode = "sgmii";
 	phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1e}>;
 };
 
 &mscc_felix_port3 {
 	status = "okay";
+	managed = "in-band-status";
 	phy-mode = "sgmii";
 	phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1f}>;
 };
diff --git a/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801.dtsi b/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801.dtsi
index a905d77..bd46adf 100644
--- a/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801.dtsi
+++ b/arch/arm/dts/fsl-ls1028a-qds-9999-sch-24801.dtsi
@@ -29,24 +29,28 @@
 
 &mscc_felix_port0 {
 	status = "okay";
+	managed = "in-band-status";
 	phy-mode = "sgmii";
 	phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1c}>;
 };
 
 &mscc_felix_port1 {
 	status = "okay";
+	managed = "in-band-status";
 	phy-mode = "sgmii";
 	phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1d}>;
 };
 
 &mscc_felix_port2 {
 	status = "okay";
+	managed = "in-band-status";
 	phy-mode = "sgmii";
 	phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1e}>;
 };
 
 &mscc_felix_port3 {
 	status = "okay";
+	managed = "in-band-status";
 	phy-mode = "sgmii";
 	phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1f}>;
 };
diff --git a/arch/arm/dts/fsl-ls1028a-qds-x3xx-sch-30841-LBRW.dtsi b/arch/arm/dts/fsl-ls1028a-qds-x3xx-sch-30841-LBRW.dtsi
index 62e818f..5909e76 100644
--- a/arch/arm/dts/fsl-ls1028a-qds-x3xx-sch-30841-LBRW.dtsi
+++ b/arch/arm/dts/fsl-ls1028a-qds-x3xx-sch-30841-LBRW.dtsi
@@ -29,24 +29,28 @@
 
 &mscc_felix_port0 {
 	status = "okay";
+	managed = "in-band-status";
 	phy-mode = "usxgmii";
 	phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@00}>;
 };
 
 &mscc_felix_port1 {
 	status = "okay";
+	managed = "in-band-status";
 	phy-mode = "usxgmii";
 	phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@01}>;
 };
 
 &mscc_felix_port2 {
 	status = "okay";
+	managed = "in-band-status";
 	phy-mode = "usxgmii";
 	phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@02}>;
 };
 
 &mscc_felix_port3 {
 	status = "okay";
+	managed = "in-band-status";
 	phy-mode = "usxgmii";
 	phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@03}>;
 };
diff --git a/arch/arm/dts/fsl-ls1028a-qds-x5xx-sch-28021-LBRW.dtsi b/arch/arm/dts/fsl-ls1028a-qds-x5xx-sch-28021-LBRW.dtsi
index 6f1f6cb..b652206 100644
--- a/arch/arm/dts/fsl-ls1028a-qds-x5xx-sch-28021-LBRW.dtsi
+++ b/arch/arm/dts/fsl-ls1028a-qds-x5xx-sch-28021-LBRW.dtsi
@@ -23,24 +23,28 @@
 
 &mscc_felix_port0 {
 	status = "okay";
+	managed = "in-band-status";
 	phy-mode = "qsgmii";
 	phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@08}>;
 };
 
 &mscc_felix_port1 {
 	status = "okay";
+	managed = "in-band-status";
 	phy-mode = "qsgmii";
 	phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@09}>;
 };
 
 &mscc_felix_port2 {
 	status = "okay";
+	managed = "in-band-status";
 	phy-mode = "qsgmii";
 	phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@0a}>;
 };
 
 &mscc_felix_port3 {
 	status = "okay";
+	managed = "in-band-status";
 	phy-mode = "qsgmii";
 	phy-handle = <&{/soc/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@0b}>;
 };
diff --git a/arch/arm/dts/fsl-ls1028a-qds.dtsi b/arch/arm/dts/fsl-ls1028a-qds.dtsi
index 0da0a7b..3b063d0 100644
--- a/arch/arm/dts/fsl-ls1028a-qds.dtsi
+++ b/arch/arm/dts/fsl-ls1028a-qds.dtsi
@@ -195,7 +195,7 @@
 	status = "okay";
 
 	rtc@51 {
-		compatible = "pcf2127-rtc";
+		compatible = "nxp,pcf2129";
 		reg = <0x51>;
 	};
 };
diff --git a/arch/arm/dts/fsl-ls1028a-rdb-u-boot.dtsi b/arch/arm/dts/fsl-ls1028a-rdb-u-boot.dtsi
new file mode 100644
index 0000000..a72b573
--- /dev/null
+++ b/arch/arm/dts/fsl-ls1028a-rdb-u-boot.dtsi
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: GPL-2.0+
+/* Copyright 2021 NXP */
+
+/*
+ * u-boot will enable the device in the linux device tree in place. Because
+ * we are using the linux device tree, we have to enable the PCI controller
+ * ourselves.
+ */
+&pcie1 {
+	status = "okay";
+};
+
+&pcie2 {
+	status = "okay";
+};
diff --git a/arch/arm/dts/fsl-ls1028a-rdb.dts b/arch/arm/dts/fsl-ls1028a-rdb.dts
index 537ebbc..639f407 100644
--- a/arch/arm/dts/fsl-ls1028a-rdb.dts
+++ b/arch/arm/dts/fsl-ls1028a-rdb.dts
@@ -1,19 +1,27 @@
-// SPDX-License-Identifier: GPL-2.0+ OR X11
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
 /*
- * NXP ls1028ARDB device tree source
+ * Device Tree file for NXP LS1028A RDB Board.
  *
- * Copyright 2019 NXP
+ * Copyright 2018-2021 NXP
+ *
+ * Harninder Rai <harninder.rai@nxp.com>
  *
  */
 
 /dts-v1/;
-
 #include "fsl-ls1028a.dtsi"
 
 / {
-	model = "NXP Layerscape 1028a RDB Board";
+	model = "LS1028A RDB Board";
 	compatible = "fsl,ls1028a-rdb", "fsl,ls1028a";
+
 	aliases {
+		crypto = &crypto;
+		serial0 = &duart0;
+		serial1 = &duart1;
+		mmc0 = &esdhc;
+		mmc1 = &esdhc1;
+		rtc1 = &ftm_alarm0;
 		spi0 = &fspi;
 		ethernet0 = &enetc_port0;
 		ethernet1 = &enetc_port2;
@@ -22,130 +30,211 @@
 		ethernet4 = &mscc_felix_port2;
 		ethernet5 = &mscc_felix_port3;
 	};
-};
-
-&dspi0 {
-	status = "okay";
-};
-
-&dspi1 {
-	status = "okay";
-};
 
-&dspi2 {
-	status = "okay";
-};
-
-&esdhc {
-	status = "okay";
-};
-
-&esdhc1 {
-	status = "okay";
-	mmc-hs200-1_8v;
-};
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
 
-&fspi {
-	status = "okay";
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x1 0x0000000>;
+	};
 
-	mt35xu02g0: flash@0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "jedec,spi-nor";
-		spi-max-frequency = <50000000>;
-		reg = <0>;
-		spi-rx-bus-width = <8>;
-		spi-tx-bus-width = <1>;
+	sys_mclk: clock-mclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
 	};
-};
 
-&i2c0 {
-	status = "okay";
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
 
-	 i2c-mux@77 {
+	sb_3v3: regulator-sb3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3_vbus";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
 
-		compatible = "nxp,pca9547";
-		reg = <0x77>;
-		#address-cells = <1>;
-		#size-cells = <0>;
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,widgets =
+			"Microphone", "Microphone Jack",
+			"Headphone", "Headphone Jack",
+			"Speaker", "Speaker Ext",
+			"Line", "Line In Jack";
+		simple-audio-card,routing =
+			"MIC_IN", "Microphone Jack",
+			"Microphone Jack", "Mic Bias",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT",
+			"Speaker Ext", "LINE_OUT";
 
-		i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0x3>;
+		simple-audio-card,cpu {
+			sound-dai = <&sai4>;
+			frame-master;
+			bitclock-master;
+		};
 
-			rtc@51 {
-				compatible = "pcf2127-rtc";
-				reg = <0x51>;
-			};
+		simple-audio-card,codec {
+			sound-dai = <&sgtl5000>;
+			frame-master;
+			bitclock-master;
+			system-clock-frequency = <25000000>;
 		};
 	};
 };
 
-&i2c1 {
+&can0 {
 	status = "okay";
-};
 
-&i2c2 {
-	status = "okay";
+	can-transceiver {
+		max-bitrate = <5000000>;
+	};
 };
 
-&i2c3 {
+&can1 {
 	status = "okay";
-};
 
-&i2c4 {
-	status = "okay";
+	can-transceiver {
+		max-bitrate = <5000000>;
+	};
 };
 
-&i2c5 {
+&duart0 {
 	status = "okay";
 };
 
-&i2c6 {
+&duart1 {
 	status = "okay";
 };
 
-&i2c7 {
-	status = "okay";
-};
+&enetc_mdio_pf3 {
+	sgmii_phy0: ethernet-phy@2 {
+		reg = <0x2>;
+	};
 
-&sata {
-	status = "okay";
-};
+	/* VSC8514 QSGMII quad PHY */
+	qsgmii_phy0: ethernet-phy@10 {
+		reg = <0x10>;
+	};
 
-&duart0 {
-	status = "okay";
-};
+	qsgmii_phy1: ethernet-phy@11 {
+		reg = <0x11>;
+	};
 
-&duart1 {
-	status = "okay";
+	qsgmii_phy2: ethernet-phy@12 {
+		reg = <0x12>;
+	};
+
+	qsgmii_phy3: ethernet-phy@13 {
+		reg = <0x13>;
+	};
 };
 
-&pcie1 {
+&enetc_port0 {
+	phy-handle = <&sgmii_phy0>;
+	phy-mode = "sgmii";
+	managed = "in-band-status";
 	status = "okay";
 };
 
-&pcie2 {
+&enetc_port2 {
 	status = "okay";
 };
 
-&usb0 {
+&esdhc {
+	sd-uhs-sdr104;
+	sd-uhs-sdr50;
+	sd-uhs-sdr25;
+	sd-uhs-sdr12;
 	status = "okay";
 };
 
-&usb1 {
+&esdhc1 {
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	bus-width = <8>;
 	status = "okay";
 };
 
-&enetc_port0 {
+&fspi {
 	status = "okay";
-	phy-mode = "sgmii";
-	phy-handle = <&rdb_phy0>;
+
+	mt35xu02g0: flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <50000000>;
+		/* The following setting enables 1-1-8 (CMD-ADDR-DATA) mode */
+		spi-rx-bus-width = <8>; /* 8 SPI Rx lines */
+		spi-tx-bus-width = <1>; /* 1 SPI Tx line */
+		reg = <0>;
+	};
 };
 
-&enetc_port2 {
+&i2c0 {
 	status = "okay";
+
+	i2c-mux@77 {
+		compatible = "nxp,pca9847";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+
+			sgtl5000: audio-codec@a {
+				#sound-dai-cells = <0>;
+				compatible = "fsl,sgtl5000";
+				reg = <0xa>;
+				VDDA-supply = <&reg_1p8v>;
+				VDDIO-supply = <&reg_1p8v>;
+				clocks = <&sys_mclk>;
+				sclk-strength = <3>;
+			};
+		};
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x02>;
+
+			current-monitor@40 {
+				compatible = "ti,ina220";
+				reg = <0x40>;
+				shunt-resistor = <500>;
+			};
+		};
+
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+
+			temperature-sensor@4c {
+				compatible = "nxp,sa56004";
+				reg = <0x4c>;
+				vcc-supply = <&sb_3v3>;
+			};
+
+			rtc@51 {
+				compatible = "nxp,pcf2129";
+				reg = <0x51>;
+			};
+		};
+	};
 };
 
 &mscc_felix {
@@ -154,28 +243,32 @@
 
 &mscc_felix_port0 {
 	label = "swp0";
-	phy-handle = <&sw_phy0>;
+	managed = "in-band-status";
+	phy-handle = <&qsgmii_phy0>;
 	phy-mode = "qsgmii";
 	status = "okay";
 };
 
 &mscc_felix_port1 {
 	label = "swp1";
-	phy-handle = <&sw_phy1>;
+	managed = "in-band-status";
+	phy-handle = <&qsgmii_phy1>;
 	phy-mode = "qsgmii";
 	status = "okay";
 };
 
 &mscc_felix_port2 {
 	label = "swp2";
-	phy-handle = <&sw_phy2>;
+	managed = "in-band-status";
+	phy-handle = <&qsgmii_phy2>;
 	phy-mode = "qsgmii";
 	status = "okay";
 };
 
 &mscc_felix_port3 {
 	label = "swp3";
-	phy-handle = <&sw_phy3>;
+	managed = "in-band-status";
+	phy-handle = <&qsgmii_phy3>;
 	phy-mode = "qsgmii";
 	status = "okay";
 };
@@ -185,26 +278,23 @@
 	status = "okay";
 };
 
-&enetc_mdio_pf3 {
+&optee {
 	status = "okay";
-	rdb_phy0: phy@2 {
-		reg = <2>;
-	};
+};
 
-	/* VSC8514 QSGMII PHY */
-	sw_phy0: phy@10 {
-		reg = <0x10>;
-	};
+&sai4 {
+	status = "okay";
+};
 
-	sw_phy1: phy@11 {
-		reg = <0x11>;
-	};
+&sata {
+	status = "okay";
+};
 
-	sw_phy2: phy@12 {
-		reg = <0x12>;
-	};
+&usb0 {
+	status = "okay";
+};
 
-	sw_phy3: phy@13 {
-		reg = <0x13>;
-	};
+&usb1 {
+	dr_mode = "otg";
+	status = "okay";
 };
diff --git a/arch/arm/dts/fsl-ls1088a-qds.dtsi b/arch/arm/dts/fsl-ls1088a-qds.dtsi
index a7d0edc..21c5007 100644
--- a/arch/arm/dts/fsl-ls1088a-qds.dtsi
+++ b/arch/arm/dts/fsl-ls1088a-qds.dtsi
@@ -88,7 +88,7 @@
 			reg = <0x3>;
 
 			rtc@51 {
-				compatible = "pcf2127-rtc";
+				compatible = "nxp,pcf2129";
 				reg = <0x51>;
 			};
 		};
diff --git a/arch/arm/dts/fsl-ls1088a-rdb.dts b/arch/arm/dts/fsl-ls1088a-rdb.dts
index de92bf2..5cdd598 100644
--- a/arch/arm/dts/fsl-ls1088a-rdb.dts
+++ b/arch/arm/dts/fsl-ls1088a-rdb.dts
@@ -135,7 +135,7 @@
 			reg = <0x3>;
 
 			rtc@51 {
-				compatible = "pcf2127-rtc";
+				compatible = "nxp,pcf2129";
 				reg = <0x51>;
 			};
 		};
diff --git a/arch/arm/dts/fsl-ls1088a-ten64.dts b/arch/arm/dts/fsl-ls1088a-ten64.dts
new file mode 100644
index 0000000..43b669c
--- /dev/null
+++ b/arch/arm/dts/fsl-ls1088a-ten64.dts
@@ -0,0 +1,377 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for Travese Ten64 (LS1088) board
+ * Based on fsl-ls1088a-rdb.dts
+ * Copyright 2017-2020 NXP
+ * Copyright 2019-2021 Traverse Technologies
+ *
+ * Author: Mathew McBride <matt@traverse.com.au>
+ */
+
+/dts-v1/;
+
+#include "fsl-ls1088a.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Traverse Ten64";
+	compatible = "traverse,ten64", "fsl,ls1088a";
+
+	aliases {
+		spi0 = &qspi;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	buttons {
+		compatible = "gpio-keys";
+
+		/* Fired by system controller when
+		 * external power off (e.g ATX Power Button)
+		 * asserted
+		 */
+		powerdn {
+			label = "External Power Down";
+			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+			interrupts = <&gpio1 17 IRQ_TYPE_EDGE_FALLING>;
+			linux,code = <KEY_POWER>;
+		};
+
+		/* Rear Panel 'ADMIN' button (GPIO_H) */
+		admin {
+			label = "ADMIN button";
+			gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>;
+			interrupts = <&gpio3 8 IRQ_TYPE_EDGE_RISING>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		sfp1down {
+			label = "ten64:green:sfp1:down";
+			gpios = <&gpio3 11 GPIO_ACTIVE_HIGH>;
+		};
+
+		sfp2up {
+			label = "ten64:green:sfp2:up";
+			gpios = <&gpio3 12 GPIO_ACTIVE_HIGH>;
+		};
+
+		admin {
+			label = "ten64:admin";
+			gpios = <&sfpgpio 12 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	sfp_xg0: dpmac2-sfp {
+		compatible = "sff,sfp";
+		i2c-bus = <&sfplower_i2c>;
+		tx-fault-gpios = <&sfpgpio 0 GPIO_ACTIVE_HIGH>;
+		tx-disable-gpios = <&sfpgpio 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sfpgpio 2 GPIO_ACTIVE_LOW>;
+		los-gpios = <&sfpgpio 3 GPIO_ACTIVE_HIGH>;
+		maximum-power-milliwatt = <2000>;
+	};
+
+	sfp_xg1: dpmac1-sfp {
+		compatible = "sff,sfp";
+		i2c-bus = <&sfpupper_i2c>;
+		tx-fault-gpios = <&sfpgpio 4 GPIO_ACTIVE_HIGH>;
+		tx-disable-gpios = <&sfpgpio 5 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sfpgpio 6 GPIO_ACTIVE_LOW>;
+		los-gpios = <&sfpgpio 7 GPIO_ACTIVE_HIGH>;
+		maximum-power-milliwatt = <2000>;
+	};
+};
+
+/* XG1 - Upper SFP */
+&dpmac1 {
+	sfp = <&sfp_xg1>;
+	phy-connection-type = "10gbase-r";
+	managed = "in-band-status";
+	status = "okay";
+};
+
+/* XG0 - Lower SFP */
+&dpmac2 {
+	sfp = <&sfp_xg0>;
+	phy-connection-type = "10gbase-r";
+	managed = "in-band-status";
+	status = "okay";
+};
+
+/* DPMAC3..6 is GE4 to GE8 */
+&dpmac3 {
+	phy-handle = <&mdio1_phy5>;
+	phy-connection-type = "qsgmii";
+	managed = "in-band-status";
+	status = "okay";
+};
+
+&dpmac4 {
+	phy-handle = <&mdio1_phy6>;
+	phy-connection-type = "qsgmii";
+	managed = "in-band-status";
+	status = "okay";
+};
+
+&dpmac5 {
+	phy-handle = <&mdio1_phy7>;
+	phy-connection-type = "qsgmii";
+	managed = "in-band-status";
+	status = "okay";
+};
+
+&dpmac6 {
+	phy-handle = <&mdio1_phy8>;
+	phy-connection-type = "qsgmii";
+	managed = "in-band-status";
+	status = "okay";
+};
+
+/* DPMAC7..10 is GE0 to GE3 */
+&dpmac7 {
+	phy-handle = <&mdio1_phy1>;
+	phy-connection-type = "qsgmii";
+	managed = "in-band-status";
+	status = "okay";
+};
+
+&dpmac8 {
+	phy-handle = <&mdio1_phy2>;
+	phy-connection-type = "qsgmii";
+	managed = "in-band-status";
+	status = "okay";
+};
+
+&dpmac9 {
+	phy-handle = <&mdio1_phy3>;
+	phy-connection-type = "qsgmii";
+	managed = "in-band-status";
+	status = "okay";
+};
+
+&dpmac10 {
+	phy-handle = <&mdio1_phy4>;
+	phy-connection-type = "qsgmii";
+	managed = "in-band-status";
+	status = "okay";
+};
+
+&serial0 {
+	status = "okay";
+};
+
+&serial1 {
+	status = "okay";
+};
+
+&emdio1 {
+	status = "okay";
+
+	mdio1_phy5: ethernet-phy@c {
+		reg = <0xc>;
+	};
+
+	mdio1_phy6: ethernet-phy@d {
+		reg = <0xd>;
+	};
+
+	mdio1_phy7: ethernet-phy@e {
+		reg = <0xe>;
+	};
+
+	mdio1_phy8: ethernet-phy@f {
+		reg = <0xf>;
+	};
+
+	mdio1_phy1: ethernet-phy@1c {
+		reg = <0x1c>;
+	};
+
+	mdio1_phy2: ethernet-phy@1d {
+		reg = <0x1d>;
+	};
+
+	mdio1_phy3: ethernet-phy@1e {
+		reg = <0x1e>;
+	};
+
+	mdio1_phy4: ethernet-phy@1f {
+		reg = <0x1f>;
+	};
+};
+
+&esdhc {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	sfpgpio: gpio@76 {
+		compatible = "ti,tca9539";
+		reg = <0x76>;
+		#gpio-cells = <2>;
+		gpio-controller;
+
+		admin_led_lower {
+			gpio-hog;
+			gpios = <13 GPIO_ACTIVE_HIGH>;
+			output-low;
+		};
+	};
+
+	at97sc: tpm@29 {
+		compatible = "atmel,at97sc3204t";
+		reg = <0x29>;
+	};
+
+	uc: board-controller@7e {
+		compatible = "traverse,ten64-controller";
+		reg = <0x7e>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	rx8035: rtc@32 {
+		compatible = "epson,rx8035";
+		reg = <0x32>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+
+	i2c-switch@70 {
+		compatible = "nxp,pca9540";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+
+		sfpupper_i2c: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		sfplower_i2c: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+	};
+};
+
+&qspi {
+	status = "okay";
+
+	en25s64: flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <4>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "bl2";
+				reg = <0 0x100000>;
+			};
+
+			partition@100000 {
+				label = "bl3";
+				reg = <0x100000 0x200000>;
+			};
+
+			partition@300000 {
+				label = "mcfirmware";
+				reg = <0x300000 0x200000>;
+			};
+
+			partition@500000 {
+				label = "ubootenv";
+				reg = <0x500000 0x80000>;
+			};
+
+			partition@580000 {
+				label = "dpl";
+				reg = <0x580000 0x40000>;
+			};
+
+			partition@5C0000 {
+				label = "dpc";
+				reg = <0x5C0000 0x40000>;
+			};
+
+			partition@600000 {
+				label = "devicetree";
+				reg = <0x600000 0x40000>;
+			};
+		};
+	};
+
+	nand: flash@1 {
+		compatible = "spi-nand";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <1>;
+		spi-max-frequency = <20000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <4>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			/* reserved for future boot direct from NAND flash
+			 * (this would use the same layout as the 8MiB NOR flash)
+			 */
+			partition@0 {
+				label = "nand-boot-reserved";
+				reg = <0 0x800000>;
+			};
+
+			/* recovery / install environment */
+			partition@800000 {
+				label = "recovery";
+				reg = <0x800000 0x2000000>;
+			};
+
+			/* ubia (first OpenWrt) - a/b names to prevent confusion with ubi0/1/etc. */
+			partition@2800000 {
+				label = "ubia";
+				reg = <0x2800000 0x6C00000>;
+			};
+
+			/* ubib (second OpenWrt) */
+			partition@9400000 {
+				label = "ubib";
+				reg = <0x9400000 0x6C00000>;
+			};
+		};
+	};
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
diff --git a/arch/arm/dts/fsl-lx2160a-qds.dtsi b/arch/arm/dts/fsl-lx2160a-qds.dtsi
index 288607c..69e11cc 100644
--- a/arch/arm/dts/fsl-lx2160a-qds.dtsi
+++ b/arch/arm/dts/fsl-lx2160a-qds.dtsi
@@ -250,7 +250,7 @@
 			reg = <0x3>;
 
 			rtc@51 {
-				compatible = "pcf2127-rtc";
+				compatible = "nxp,pcf2129";
 				reg = <0x51>;
 			};
 		};
diff --git a/arch/arm/dts/fsl-lx2160a-rdb.dts b/arch/arm/dts/fsl-lx2160a-rdb.dts
index 5fbdd90..8ca4afa 100644
--- a/arch/arm/dts/fsl-lx2160a-rdb.dts
+++ b/arch/arm/dts/fsl-lx2160a-rdb.dts
@@ -117,7 +117,7 @@
 	status = "okay";
 
 	rtc@51 {
-		compatible = "pcf2127-rtc";
+		compatible = "nxp,pcf2129";
 		reg = <0x51>;
 	};
 };
diff --git a/arch/arm/dts/ls1021a-pg-wcom-expu1.dts b/arch/arm/dts/ls1021a-pg-wcom-expu1.dts
index 33456b7..ec8e7de 100644
--- a/arch/arm/dts/ls1021a-pg-wcom-expu1.dts
+++ b/arch/arm/dts/ls1021a-pg-wcom-expu1.dts
@@ -87,7 +87,6 @@
 			label = "qe";
 			reg = <0x20000 0x20000>;
 		};
-		/* ZL30343 init data to be added here */
 		partition@40000 {
 			label = "envred";
 			reg = <0x40000 0x20000>;
@@ -101,8 +100,20 @@
 			reg = <0x100000 0x100000>;
 		};
 		partition@200000 {
+			label = "redenvred";
+			reg = <0x200000 0x20000>;
+		};
+		partition@220000 {
+			label = "redenv";
+			reg = <0x220000 0x20000>;
+		};
+		partition@240000 {
+			label = "redu-boot";
+			reg = <0x240000 0x100000>;
+		};
+		partition@340000 {
 			label = "ubi0";
-			reg = <0x200000 0x3E00000>;
+			reg = <0x340000 0x03C00000>;
 		};
 	};
 };
diff --git a/arch/arm/dts/ls1021a-pg-wcom-seli8.dts b/arch/arm/dts/ls1021a-pg-wcom-seli8.dts
index e335188..03ce3ab 100644
--- a/arch/arm/dts/ls1021a-pg-wcom-seli8.dts
+++ b/arch/arm/dts/ls1021a-pg-wcom-seli8.dts
@@ -38,6 +38,7 @@
 &enet2 {
 	phy-handle = <&debug_phy>;
 	phy-connection-type = "rgmii-id";
+	max-speed = <100>;
 	status = "okay";
 };
 
@@ -82,8 +83,20 @@
 			reg = <0x100000 0x100000>;
 		};
 		partition@200000 {
+			label = "redenvred";
+			reg = <0x200000 0x20000>;
+		};
+		partition@220000 {
+			label = "redenv";
+			reg = <0x220000 0x20000>;
+		};
+		partition@240000 {
+			label = "redu-boot";
+			reg = <0x240000 0x100000>;
+		};
+		partition@340000 {
 			label = "ubi0";
-			reg = <0x200000 0x3E00000>;
+			reg = <0x340000 0x03C00000>;
 		};
 	};
 };
diff --git a/board/freescale/ls1043ardb/ls1043ardb.c b/board/freescale/ls1043ardb/ls1043ardb.c
index beef26b..1764c93 100644
--- a/board/freescale/ls1043ardb/ls1043ardb.c
+++ b/board/freescale/ls1043ardb/ls1043ardb.c
@@ -219,6 +219,10 @@
 	ppa_init();
 #endif
 
+#if !defined(CONFIG_SYS_EARLY_PCI_INIT) && defined(CONFIG_DM_ETH)
+	pci_init();
+#endif
+
 #ifdef CONFIG_U_QE
 	u_qe_init();
 #endif
diff --git a/board/freescale/ls1046ardb/ls1046ardb.c b/board/freescale/ls1046ardb/ls1046ardb.c
index 93ef903..d0abfe8 100644
--- a/board/freescale/ls1046ardb/ls1046ardb.c
+++ b/board/freescale/ls1046ardb/ls1046ardb.c
@@ -93,6 +93,10 @@
 	ppa_init();
 #endif
 
+#if !defined(CONFIG_SYS_EARLY_PCI_INIT) && defined(CONFIG_DM_ETH)
+	pci_init();
+#endif
+
 	/* invert AQR105 IRQ pins polarity */
 	out_be32(&scfg->intpcr, AQR105_IRQ_MASK);
 
diff --git a/board/freescale/ls1088a/ls1088a.c b/board/freescale/ls1088a/ls1088a.c
index aa548b2..63e824c 100644
--- a/board/freescale/ls1088a/ls1088a.c
+++ b/board/freescale/ls1088a/ls1088a.c
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0+
 /*
- * Copyright 2017-2018 NXP
+ * Copyright 2017-2022 NXP
  */
 #include <common.h>
 #include <clock_legacy.h>
@@ -904,10 +904,10 @@
 	}
 
 	if (disable_ifc) {
-		offset = fdt_path_offset(fdt, "/soc/ifc/nor");
+		offset = fdt_path_offset(fdt, "/soc/memory-controller/nor");
 
 		if (offset < 0)
-			offset = fdt_path_offset(fdt, "/ifc/nor");
+			offset = fdt_path_offset(fdt, "/memory-controller/nor");
 	} else {
 		offset = fdt_path_offset(fdt, "/soc/quadspi");
 
@@ -917,10 +917,10 @@
 
 #else
 #ifdef CONFIG_FSL_QSPI
-	offset = fdt_path_offset(fdt, "/soc/ifc/nor");
+	offset = fdt_path_offset(fdt, "/soc/memory-controller/nor");
 
 	if (offset < 0)
-		offset = fdt_path_offset(fdt, "/ifc/nor");
+		offset = fdt_path_offset(fdt, "/memory-controller/nor");
 #else
 	offset = fdt_path_offset(fdt, "/soc/quadspi");
 
diff --git a/board/keymile/Kconfig b/board/keymile/Kconfig
index 7dd8213..863c07d 100644
--- a/board/keymile/Kconfig
+++ b/board/keymile/Kconfig
@@ -130,6 +130,38 @@
 	help
 	  Page size of inventory in EEPROM.
 
+config PG_WCOM_UBOOT_UPDATE_SUPPORTED
+	bool "Enable U-boot Field Fail-Safe Update Functionality"
+	default n
+	help
+	  Indicates that field fail-safe u-boot update is supported.
+	  This functionality works only for designs that are booting
+	  from parallel NOR flash.
+
+config PG_WCOM_UBOOT_BOOTPACKAGE
+	bool "U-boot Is Part Of Factory Boot-Package Image"
+	default n
+	help
+	  Indicates that u-boot will be a part of the factory programmed
+	  boot-package image.
+	  Has to be set for original u-boot programmed at factory.
+
+config PG_WCOM_UBOOT_UPDATE_TEXT_BASE
+	hex "Text Base For U-boot Programmed Outside Factory"
+	default 0xFFFFFFFF
+	help
+	  Text base of an updated u-boot that is not factory programmed but
+	  later when the unit is rolled out on the field.
+	  Has to be set for original u-boot programmed at factory.
+
+config PG_WCOM_UBOOT_UPDATE
+	bool "U-boot Is Part Of Factory Boot-Package Image"
+	default n
+	help
+	  Indicates that u-boot will be a part of the embedded software and
+	  programmed at field.
+	  Has to be set for updated u-boot version programmed at field.
+
 source "board/keymile/km83xx/Kconfig"
 source "board/keymile/kmcent2/Kconfig"
 source "board/keymile/km_arm/Kconfig"
diff --git a/board/keymile/README b/board/keymile/README
new file mode 100644
index 0000000..4e5cfb1
--- /dev/null
+++ b/board/keymile/README
@@ -0,0 +1,18 @@
+Field Fail-Save U-boot Update
+-----------------------------
+Field Fail-Save u-boot update is a feature that allows save u-boot update
+of FOX and XMC products that are rolled out in the field.
+
+The feature is initially implemented for designs based on LS102x SoC, but in
+theory can be used on all designs that are booting from parallel NOR flash.
+
+The implementation expects redundant (secondary) u-boot image on a predefined
+location in the NOR flash, u-boot execution will be transferred to the redundant 
+(secondary) u-boot and redundant u-boot will be started if 'updateduboot' envvar
+is set to 'yes'.
+Update logic check_for_uboot_update() has to be invoked from the design early
+before relocation just after SoC initialization, e.g from board_early_init_f or
+misc_init_f functions.
+By design it is expected that primary u-boot image is burned in the factory and
+never updated, and in case u-boot update is required it can flashed and started
+from secondary u-boot location.
diff --git a/board/keymile/common/common.c b/board/keymile/common/common.c
index ff07260..3999f48 100644
--- a/board/keymile/common/common.c
+++ b/board/keymile/common/common.c
@@ -19,6 +19,8 @@
 #include <asm/io.h>
 #include <linux/ctype.h>
 #include <linux/delay.h>
+#include <linux/bug.h>
+#include <bootcount.h>
 
 #if defined(CONFIG_POST)
 #include "post.h"
@@ -76,6 +78,57 @@
 	return 0;
 }
 
+#if CONFIG_IS_ENABLED(PG_WCOM_UBOOT_UPDATE_SUPPORTED)
+#if   ((!CONFIG_IS_ENABLED(PG_WCOM_UBOOT_BOOTPACKAGE) && \
+	!CONFIG_IS_ENABLED(PG_WCOM_UBOOT_UPDATE)) ||     \
+	(CONFIG_IS_ENABLED(PG_WCOM_UBOOT_BOOTPACKAGE) && \
+	CONFIG_IS_ENABLED(PG_WCOM_UBOOT_UPDATE)))
+#error "It has to be either bootpackage or update u-boot image!"
+#endif
+void check_for_uboot_update(void)
+{
+	void (*uboot_update_entry)(void) =
+		(void (*)(void)) CONFIG_PG_WCOM_UBOOT_UPDATE_TEXT_BASE;
+	char *isupdated = env_get("updateduboot");
+	ulong bootcount = bootcount_load();
+	ulong ebootcount = 0;
+
+	if (IS_ENABLED(CONFIG_PG_WCOM_UBOOT_BOOTPACKAGE)) {
+		/*
+		 * When running in factory burned u-boot move to the updated
+		 * u-boot version only if updateduboot envvar is set to 'yes'
+		 * and bootcount limit is not exceeded.
+		 * Board must be able to start in factory bootloader mode!
+		 */
+		if (isupdated && !strncmp(isupdated, "yes", 3) &&
+		    bootcount <= CONFIG_BOOTCOUNT_BOOTLIMIT) {
+			printf("Check update: update detected, ");
+			printf("starting new image @%08x ...\n",
+			       CONFIG_PG_WCOM_UBOOT_UPDATE_TEXT_BASE);
+			ebootcount = early_bootcount_load();
+			if (ebootcount <= CONFIG_BOOTCOUNT_BOOTLIMIT) {
+				early_bootcount_store(++ebootcount);
+				uboot_update_entry();
+			} else {
+				printf("Check update: warning: ");
+				printf("early bootcount exceeded (%lu)\n",
+				       ebootcount);
+			}
+		}
+		printf("Check update: starting factory image @%08x ...\n",
+		       CONFIG_SYS_TEXT_BASE);
+	} else if (IS_ENABLED(CONFIG_PG_WCOM_UBOOT_UPDATE)) {
+		/*
+		 * When running in field updated u-boot, make sure that
+		 * bootcount limit is never exceeded. Must never happen!
+		 */
+		WARN_ON(bootcount > CONFIG_BOOTCOUNT_BOOTLIMIT);
+		printf("Check update: updated u-boot starting @%08x ...\n",
+		       CONFIG_SYS_TEXT_BASE);
+	}
+}
+#endif
+
 #if defined(CONFIG_SYS_I2C_INIT_BOARD)
 static void i2c_write_start_seq(void)
 {
diff --git a/board/keymile/common/common.h b/board/keymile/common/common.h
index 15a3c37..d16c824 100644
--- a/board/keymile/common/common.h
+++ b/board/keymile/common/common.h
@@ -133,6 +133,10 @@
 
 int set_km_env(void);
 
+ulong early_bootcount_load(void);
+void early_bootcount_store(ulong ebootcount);
+void check_for_uboot_update(void);
+
 #define DELAY_ABORT_SEQ		62  /* @200kHz 9 clocks = 44us, 62us is ok */
 #define DELAY_HALF_PERIOD	(500 / (CONFIG_SYS_I2C_SPEED / 1000))
 
diff --git a/board/keymile/common/qrio.c b/board/keymile/common/qrio.c
index da51691..5401bdd 100644
--- a/board/keymile/common/qrio.c
+++ b/board/keymile/common/qrio.c
@@ -27,6 +27,32 @@
 	       (id_rev >> 8) & 0xff, id_rev & 0xff);
 }
 
+#define SLFTEST_OFF		0x06
+
+bool qrio_get_selftest_pin(void)
+{
+	u8 slftest;
+
+	void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
+
+	slftest = in_8(qrio_base + SLFTEST_OFF);
+
+	return (slftest & 1) > 0;
+}
+
+#define BPRTH_OFF		0x04
+
+bool qrio_get_pgy_pres_pin(void)
+{
+	u8 pgy_pres;
+
+	void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
+
+	pgy_pres = in_8(qrio_base + BPRTH_OFF);
+
+	return (pgy_pres & 0x80) > 0;
+}
+
 int qrio_get_gpio(u8 port_off, u8 gpio_nr)
 {
 	u32 gprt;
@@ -244,6 +270,44 @@
 	out_8(qrio_base + RSTCFG_OFF, rstcfg);
 }
 
+/* Early bootcount memory area is avilable starting from QRIO3 Rev.2 */
+#define QRIO3_ID		0x71
+#define QRIO3_REV		0x02
+#define EBOOTCNT_OFF		0x28
+
+ulong early_bootcount_load(void)
+{
+	void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
+	u16 id_rev = in_be16(qrio_base + ID_REV_OFF);
+	u8 id = (id_rev >> 8) & 0xff;
+	u8 rev = id_rev & 0xff;
+	u32 ebootcount = 0;
+
+	if (id == QRIO3_ID && rev >= QRIO3_REV) {
+		ebootcount = in_be32(qrio_base + EBOOTCNT_OFF);
+	} else {
+		printf("QRIO: warning: early bootcount not supported, ");
+		printf("id = %u, rev = %u\n", id, rev);
+	}
+
+	return ebootcount;
+}
+
+void early_bootcount_store(ulong ebootcount)
+{
+	void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
+	u16 id_rev = in_be16(qrio_base + ID_REV_OFF);
+	u8 id = (id_rev >> 8) & 0xff;
+	u8 rev = id_rev & 0xff;
+
+	if (id == QRIO3_ID && rev >= QRIO3_REV) {
+		out_be32(qrio_base + EBOOTCNT_OFF, ebootcount);
+	} else {
+		printf("QRIO: warning: early bootcount not supported, ");
+		printf("id = %u, rev = %u\n", id, rev);
+	}
+}
+
 /* I2C deblocking uses the algorithm defined in board/keymile/common/common.c
  * 2 dedicated QRIO GPIOs externally pull the SCL and SDA lines
  * For I2C only the low state is activly driven and high state is pulled-up
diff --git a/board/keymile/common/qrio.h b/board/keymile/common/qrio.h
index 757bcbf..2b997d9 100644
--- a/board/keymile/common/qrio.h
+++ b/board/keymile/common/qrio.h
@@ -12,6 +12,8 @@
 #define QRIO_GPIO_B		0x60
 
 void show_qrio(void);
+bool qrio_get_selftest_pin(void);
+bool qrio_get_pgy_pres_pin(void);
 int qrio_get_gpio(u8 port_off, u8 gpio_nr);
 void qrio_set_opendrain_gpio(u8 port_off, u8 gpio_nr, u8 val);
 void qrio_set_gpio(u8 port_off, u8 gpio_nr, bool value);
diff --git a/board/keymile/pg-wcom-ls102xa/MAINTAINERS b/board/keymile/pg-wcom-ls102xa/MAINTAINERS
index 966c88b..33db2b2 100644
--- a/board/keymile/pg-wcom-ls102xa/MAINTAINERS
+++ b/board/keymile/pg-wcom-ls102xa/MAINTAINERS
@@ -7,6 +7,8 @@
 F:	include/configs/pg-wcom-seli8.h
 F:	include/configs/pg-wcom-expu1.h
 F:	configs/pg_wcom_seli8_defconfig
+F:	configs/pg_wcom_seli8_update_defconfig
 F:	configs/pg_wcom_expu1_defconfig
+F:	configs/pg_wcom_expu1_update_defconfig
 F:	arch/arm/dts/ls1021a-pg-wcom-seli8.dts
 F:	arch/arm/dts/ls1021a-pg-wcom-expu1.dts
diff --git a/board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c b/board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c
index db49e8f..467f110 100644
--- a/board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c
+++ b/board/keymile/pg-wcom-ls102xa/pg-wcom-ls102xa.c
@@ -91,8 +91,10 @@
 	qrio_prstcfg(WCOM_CLIPS_RST, PRSTCFG_POWUP_UNIT_RST);
 	qrio_prst(WCOM_CLIPS_RST, false, false);
 #endif
+
+	/* deasset debug phy reset only if piggy is present */
 	qrio_prstcfg(KM_DBG_ETH_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
-	qrio_prst(KM_DBG_ETH_RST, false, false);
+	qrio_prst(KM_DBG_ETH_RST, !qrio_get_pgy_pres_pin(), false);
 
 	i2c_deblock_gpio_cfg();
 
@@ -104,6 +106,13 @@
 
 	arch_soc_init();
 
+	return 0;
+}
+
+int misc_init_f(void)
+{
+	if (IS_ENABLED(CONFIG_PG_WCOM_UBOOT_UPDATE_SUPPORTED))
+		check_for_uboot_update();
 	return 0;
 }
 
@@ -128,8 +137,7 @@
 
 int misc_init_r(void)
 {
-	if (IS_ENABLED(CONFIG_FSL_DEVICE_DISABLE))
-		device_disable(devdis_tbl, ARRAY_SIZE(devdis_tbl));
+	device_disable(devdis_tbl, ARRAY_SIZE(devdis_tbl));
 
 	ivm_read_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN,
 			CONFIG_PIGGY_MAC_ADDRESS_OFFSET);
@@ -150,24 +158,22 @@
 #if defined(CONFIG_POST)
 int post_hotkeys_pressed(void)
 {
-	/* DIC26_SELFTEST: GPRTA0, GPA0 */
-	qrio_gpio_direction_input(QRIO_GPIO_A, 0);
-	return qrio_get_gpio(QRIO_GPIO_A, 0);
+	/* DIC26_SELFTEST: QRIO, SLFTEST */
+	return qrio_get_selftest_pin();
 }
 
+/* POST word is located in the unused SCRATCHRW4 register */
+#define CCSR_SCRATCHRW4_ADDR		0x1ee020c
+
 ulong post_word_load(void)
 {
-	/* POST word is located at the beginning of reserved physical RAM */
-	void *addr = (void *)(CONFIG_SYS_SDRAM_BASE +
-				gd->ram_size - CONFIG_KM_RESERVED_PRAM + 8);
+	void *addr = (void *)CCSR_SCRATCHRW4_ADDR;
 	return in_le32(addr);
 }
 
 void post_word_store(ulong value)
 {
-	/* POST word is located at the beginning of reserved physical RAM */
-	void *addr = (void *)(CONFIG_SYS_SDRAM_BASE +
-				gd->ram_size - CONFIG_KM_RESERVED_PRAM + 8);
+	void *addr = (void *)CCSR_SCRATCHRW4_ADDR;
 	out_le32(addr, value);
 }
 
diff --git a/board/traverse/common/Kconfig b/board/traverse/common/Kconfig
new file mode 100644
index 0000000..d34832b
--- /dev/null
+++ b/board/traverse/common/Kconfig
@@ -0,0 +1,6 @@
+config TEN64_CONTROLLER
+	bool "Enable Ten64 board controller driver"
+	depends on TARGET_TEN64
+	help
+		Support for the board microcontroller on the Traverse
+		Ten64 family of boards.
diff --git a/board/traverse/common/Makefile b/board/traverse/common/Makefile
new file mode 100644
index 0000000..d31e353
--- /dev/null
+++ b/board/traverse/common/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_TEN64_CONTROLLER) += ten64_controller.o
diff --git a/board/traverse/common/ten64-controller.h b/board/traverse/common/ten64-controller.h
new file mode 100644
index 0000000..fed6af4
--- /dev/null
+++ b/board/traverse/common/ten64-controller.h
@@ -0,0 +1,28 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+#ifndef TEN64_CNTRL_H
+#define TEN64_CNTRL_H
+
+/**
+ * struct t64uc_board_info - Board Information Structure
+ * @mac: Base MAC address
+ * @cpuId: Microcontroller unique serial number
+ * @fwversion_major: Microcontroller version number (Major)
+ * @fwversion_minor: Microcontroller version number (Minor)
+ * @fwversion_patch: Microcontroller version number (Patch)
+ */
+struct t64uc_board_info {
+	u8 mac[6];
+	u32 cpuId[4];
+	u8 fwversion_major;
+	u8 fwversion_minor;
+	u8 fwversion_patch;
+} __packed;
+
+enum {
+	TEN64_CNTRL_GET_BOARD_INFO,
+	TEN64_CNTRL_10G_OFF,
+	TEN64_CNTRL_10G_ON,
+	TEN64_CNTRL_SET_NEXT_BOOTSRC
+};
+
+#endif
diff --git a/board/traverse/common/ten64_controller.c b/board/traverse/common/ten64_controller.c
new file mode 100644
index 0000000..d6ef8a8
--- /dev/null
+++ b/board/traverse/common/ten64_controller.c
@@ -0,0 +1,240 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+/* Ten64 Board Microcontroller Driver
+ * Copyright 2021 Traverse Technologies Australia
+ *
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <misc.h>
+#include <i2c.h>
+#include <hexdump.h>
+#include <dm/device_compat.h>
+#include <inttypes.h>
+#include <linux/delay.h>
+
+#include "ten64-controller.h"
+
+/* Microcontroller command set and structure
+ * These should not be used outside this file
+ */
+
+#define T64_UC_DATA_MAX_SIZE            128U
+#define T64_UC_API_MSG_HEADER_SIZE      4U
+#define T64_UC_API_HEADER_PREAMB        0xcabe
+
+enum {
+	TEN64_UC_CMD_SET_BOARD_MAC = 0x10,
+	TEN64_UC_CMD_GET_BOARD_INFO = 0x11,
+	TEN64_UC_CMD_GET_STATE = 0x20,
+	TEN64_UC_CMD_SET_RESET_BTN_HOLD_TIME = 0x21,
+	TEN64_UC_CMD_ENABLE_RESET_BUTTON = 0x22,
+	TEN64_UC_CMD_SET_NEXT_BOOTSRC = 0x23,
+	TEN64_UC_CMD_ENABLE_10G = 0x24,
+	TEN64_UC_CMD_FWUP_GET_INFO = 0xA0,
+	TEN64_UC_CMD_FWUP_INIT = 0xA1,
+	TEN64_UC_CMD_FWUP_XFER = 0xA2,
+	TEN64_UC_CMD_FWUP_CHECK = 0xA3,
+	TEN64_UC_CMD_FWUPBOOT = 0x0A
+};
+
+/** struct t64uc_message - Wire Format for microcontroller messages
+ * @preamb: Message preamble (always 0xcabe)
+ * @cmd: Command to invoke
+ * @len: Length of data
+ * @data: Command data, up to 128 bytes
+ */
+struct t64uc_message {
+	u16 preamb;
+	u8 cmd;
+	u8 len;
+	u8 data[T64_UC_DATA_MAX_SIZE];
+}  __packed;
+
+enum {
+	T64_CTRL_IO_SET = 1U,
+	T64_CTRL_IO_CLEAR = 2U,
+	T64_CTRL_IO_TOGGLE = 3U,
+	T64_CTRL_IO_RESET = 4U,
+	T64_CTRL_IO_UNKNOWN = 5U
+};
+
+/** struct t64uc_board_10g_enable - Wrapper for 10G enable command
+ * @control: state to set the 10G retimer - either
+ *	     T64_CTRL_IO_CLEAR (0x02) for off or
+ *	     T64_CTRL_IO_SET (0x01) for on.
+ *
+ * This struct exists to simplify the wrapping of the
+ * command value into a microcontroller message and passing into
+ * functions.
+ */
+struct t64uc_board_10g_enable {
+	u8 control;
+} __packed;
+
+/** ten64_controller_send_recv_command() - Wrapper function to
+ * send a command to the microcontroller.
+ * @uc_chip: the DM I2C chip handle for the microcontroller
+ * @uc_cmd: the microcontroller API command code
+ * @uc_cmd_data: pointer to the data struct for this command
+ * @uc_data_len: size of command data struct
+ * @return_data: place to store response from microcontroller, NULL if not expected
+ * @expected_return_len: expected size of microcontroller command response
+ * @return_message_wait: wait this long (in us) before reading the response
+ *
+ * Invoke a microcontroller command and receive a response.
+ * This function includes communicating with the microcontroller over
+ * I2C and encoding a message in the wire format.
+ *
+ * Return: 0 if successful, error code otherwise.
+ * Returns -EBADMSG if the microcontroller response could not be validated,
+ * other error codes may be passed from dm_i2c_xfer()
+ */
+static int ten64_controller_send_recv_command(struct udevice *ucdev, u8 uc_cmd,
+					      void *uc_cmd_data, u8 cmd_data_len,
+					      void *return_data, u8 expected_return_len,
+					      u16 return_message_wait)
+{
+	int ret;
+	struct t64uc_message send, recv;
+	struct i2c_msg command_message, return_message;
+	struct dm_i2c_chip *chip = dev_get_parent_plat(ucdev);
+
+	dev_dbg(ucdev, "%s sending cmd %02X len %d\n", __func__, uc_cmd, cmd_data_len);
+
+	send.preamb = T64_UC_API_HEADER_PREAMB;
+	send.cmd = uc_cmd;
+	send.len = cmd_data_len;
+	if (uc_cmd_data && cmd_data_len > 0)
+		memcpy(send.data, uc_cmd_data, cmd_data_len);
+
+	command_message.addr = chip->chip_addr;
+	command_message.len = T64_UC_API_MSG_HEADER_SIZE + send.len;
+	command_message.buf = (void *)&send;
+	command_message.flags = I2C_M_STOP;
+
+	ret = dm_i2c_xfer(ucdev, &command_message, 1);
+	if (!return_data)
+		return ret;
+
+	udelay(return_message_wait);
+
+	return_message.addr = chip->chip_addr;
+	return_message.len = T64_UC_API_MSG_HEADER_SIZE + expected_return_len;
+	return_message.buf = (void *)&recv;
+	return_message.flags = I2C_M_RD;
+
+	ret = dm_i2c_xfer(ucdev, &return_message, 1);
+	if (ret)
+		return ret;
+
+	if (recv.preamb != T64_UC_API_HEADER_PREAMB) {
+		dev_err(ucdev, "%s: No preamble received in microcontroller response\n",
+			__func__);
+		return -EBADMSG;
+	}
+	if (recv.cmd != uc_cmd) {
+		dev_err(ucdev, "%s: command response mismatch, got %02X expecting %02X\n",
+			__func__, recv.cmd, uc_cmd);
+		return -EBADMSG;
+	}
+	if (recv.len != expected_return_len) {
+		dev_err(ucdev, "%s: received message has unexpected length, got %d expected %d\n",
+			__func__, recv.len, expected_return_len);
+		return -EBADMSG;
+	}
+	memcpy(return_data, recv.data, expected_return_len);
+	return ret;
+}
+
+/** ten64_controller_send_command() - Send command to microcontroller without
+ * expecting a response (for example, invoking a control command)
+ * @uc_chip: the DM I2C chip handle for the microcontroller
+ * @uc_cmd: the microcontroller API command code
+ * @uc_cmd_data: pointer to the data struct for this command
+ * @uc_data_len: size of command data struct
+ */
+static int ten64_controller_send_command(struct udevice *ucdev, u8 uc_cmd,
+					 void *uc_cmd_data, u8 cmd_data_len)
+{
+	return ten64_controller_send_recv_command(ucdev, uc_cmd,
+						  uc_cmd_data, cmd_data_len,
+						  NULL, 0, 0);
+}
+
+/** ten64_controller_get_board_info() -Get board information from microcontroller
+ * @dev: The microcontroller device handle
+ * @out: Pointer to a t64uc_board_info struct that has been allocated by the caller
+ */
+static int ten64_controller_get_board_info(struct udevice *dev, struct t64uc_board_info *out)
+{
+	int ret;
+
+	ret = ten64_controller_send_recv_command(dev, TEN64_UC_CMD_GET_BOARD_INFO,
+						 NULL, 0, out,
+						 sizeof(struct t64uc_board_info),
+						 10000);
+	if (ret) {
+		dev_err(dev, "%s unable to send board info command: %d\n",
+			__func__, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+/**
+ * ten64_controller_10g_enable_command() - Sends a 10G (Retimer) enable command
+ * to the microcontroller.
+ * @ucdev: The microcontroller udevice
+ * @value: The value flag for the 10G state
+ */
+static int ten64_controller_10g_enable_command(struct udevice *ucdev, u8 value)
+{
+	int ret;
+	struct t64uc_board_10g_enable enable_msg;
+
+	enable_msg.control = value;
+
+	ret = ten64_controller_send_command(ucdev, TEN64_UC_CMD_ENABLE_10G,
+					    &enable_msg, sizeof(enable_msg));
+	if (ret) {
+		dev_err(ucdev, "ERROR sending uC 10G Enable message: %d\n", ret);
+		return -1;
+	}
+
+	return 0;
+}
+
+int ten64_controller_call(struct udevice *dev, int msgid, void *tx_msg, int tx_size,
+			  void *rx_msg, int rx_size)
+{
+	switch (msgid) {
+	case TEN64_CNTRL_GET_BOARD_INFO:
+		return ten64_controller_get_board_info(dev, (struct t64uc_board_info *)rx_msg);
+	case TEN64_CNTRL_10G_OFF:
+		return ten64_controller_10g_enable_command(dev, T64_CTRL_IO_CLEAR);
+	case TEN64_CNTRL_10G_ON:
+		return ten64_controller_10g_enable_command(dev, T64_CTRL_IO_SET);
+	default:
+		dev_err(dev, "%s: Unknown operation %d\n", __func__, msgid);
+	}
+	return -EINVAL;
+}
+
+static struct misc_ops ten64_ctrl_ops  = {
+	.call = ten64_controller_call
+};
+
+static const struct udevice_id ten64_controller_ids[] = {
+	{.compatible = "traverse,ten64-controller"},
+	{}
+};
+
+U_BOOT_DRIVER(ten64_controller) = {
+	.name = "ten64-controller-i2c",
+	.id = UCLASS_MISC,
+	.of_match = ten64_controller_ids,
+	.ops = &ten64_ctrl_ops
+};
diff --git a/board/traverse/ten64/Kconfig b/board/traverse/ten64/Kconfig
new file mode 100644
index 0000000..ea8e3ea
--- /dev/null
+++ b/board/traverse/ten64/Kconfig
@@ -0,0 +1,17 @@
+if TARGET_TEN64
+
+config SYS_BOARD
+	default "ten64"
+
+config SYS_VENDOR
+	default "traverse"
+
+config SYS_SOC
+	default "fsl-layerscape"
+
+config SYS_CONFIG_NAME
+	default "ten64"
+
+endif
+
+source "board/traverse/common/Kconfig"
diff --git a/board/traverse/ten64/MAINTAINERS b/board/traverse/ten64/MAINTAINERS
new file mode 100644
index 0000000..7b53e87
--- /dev/null
+++ b/board/traverse/ten64/MAINTAINERS
@@ -0,0 +1,8 @@
+TEN64 BOARD
+M:	Mathew McBride <matt@traverse.com.au>
+S:	Maintained
+F:	arch/arm/dts/fsl-ls1088a-ten64.dts
+F:	board/traverse/ten64/
+F:	board/traverse/common/
+F:	include/configs/ten64.h
+F:	configs/ten64_tfa_defconfig
diff --git a/board/traverse/ten64/Makefile b/board/traverse/ten64/Makefile
new file mode 100644
index 0000000..fd8d5cc
--- /dev/null
+++ b/board/traverse/ten64/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0+
+
+obj-y += ten64.o
+obj-y += eth_ten64.o
+
+CFLAGS_ten64.o += -DDEBUG
diff --git a/board/traverse/ten64/eth_ten64.c b/board/traverse/ten64/eth_ten64.c
new file mode 100644
index 0000000..3f96e57
--- /dev/null
+++ b/board/traverse/ten64/eth_ten64.c
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2017 NXP
+ * Copyright 2019-2021 Traverse Technologies Australia
+ */
+#include <common.h>
+#include <command.h>
+#include <netdev.h>
+#include <malloc.h>
+#include <fsl_mdio.h>
+#include <miiphy.h>
+#include <phy.h>
+#include <fm_eth.h>
+#include <asm/io.h>
+#include <exports.h>
+#include <asm/arch/fsl_serdes.h>
+#include <fsl-mc/fsl_mc.h>
+#include <fsl-mc/ldpaa_wriop.h>
+
+void reset_phy(void)
+{
+	mc_env_boot();
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	/* These settings only apply to VSC8514 */
+	if (phydev->phy_id == 0x70670) {
+		/* First, ensure LEDs are driven to rails (not tristate)
+		 * This is in the extended page 0x0010
+		 */
+		phy_write(phydev, MDIO_DEVAD_NONE, 0x1F, 0x0010);
+		phy_write(phydev, MDIO_DEVAD_NONE, 0x0E, 0x2000);
+		/* Restore to page 0 */
+		phy_write(phydev, MDIO_DEVAD_NONE, 0x1F, 0x0000);
+
+		/* Disable blink on the left LEDs, and make the activity LEDs blink faster */
+		phy_write(phydev, MDIO_DEVAD_NONE, 0x1E, 0xC03);
+
+		phy_write(phydev, MDIO_DEVAD_NONE, 0x1D, 0x3421);
+	}
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
diff --git a/board/traverse/ten64/ten64.c b/board/traverse/ten64/ten64.c
new file mode 100644
index 0000000..bdabc21
--- /dev/null
+++ b/board/traverse/ten64/ten64.c
@@ -0,0 +1,438 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Traverse Ten64 Family board
+ * Copyright 2017-2018 NXP
+ * Copyright 2019-2021 Traverse Technologies
+ */
+#include <common.h>
+#include <dm/uclass.h>
+#include <env.h>
+#include <i2c.h>
+#include <init.h>
+#include <log.h>
+#include <malloc.h>
+#include <errno.h>
+#include <misc.h>
+#include <netdev.h>
+#include <fsl_ifc.h>
+#include <fsl_ddr.h>
+#include <fsl_sec.h>
+#include <asm/global_data.h>
+#include <asm/io.h>
+#include <fdt_support.h>
+#include <linux/delay.h>
+#include <linux/libfdt.h>
+#include <fsl-mc/fsl_mc.h>
+#include <env_internal.h>
+#include <asm/arch-fsl-layerscape/soc.h>
+#include <asm/arch/ppa.h>
+#include <hwconfig.h>
+#include <asm/arch/fsl_serdes.h>
+#include <asm/arch/soc.h>
+#include <asm/arch-fsl-layerscape/fsl_icid.h>
+
+#include <fsl_immap.h>
+
+#include "../common/ten64-controller.h"
+
+#define I2C_RETIMER_ADDR		0x27
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static int ten64_read_board_info(struct t64uc_board_info *);
+static void ten64_set_macaddrs_from_board_info(struct t64uc_board_info *);
+static void ten64_board_retimer_ds110df410_init(void);
+
+enum {
+	TEN64_BOARD_REV_A = 0xFF,
+	TEN64_BOARD_REV_B = 0xFE,
+	TEN64_BOARD_REV_C = 0xFD
+};
+
+#define RESV_MEM_IN_BANK(b)	(gd->arch.resv_ram >= base[b] && \
+				 gd->arch.resv_ram < base[b] + size[b])
+
+int board_early_init_f(void)
+{
+	fsl_lsch3_early_init_f();
+	return 0;
+}
+
+static u32 ten64_get_board_rev(void)
+{
+	struct ccsr_gur *dcfg = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
+	u32 board_rev_in = in_le32(&dcfg->gpporcr1);
+	return board_rev_in;
+}
+
+int checkboard(void)
+{
+	enum boot_src src = get_boot_src();
+	char boardmodel[32];
+	struct t64uc_board_info boardinfo;
+	u32 board_rev = ten64_get_board_rev();
+
+	switch (board_rev) {
+	case TEN64_BOARD_REV_A:
+		snprintf(boardmodel, 32, "1064-0201A (Alpha)");
+		break;
+	case TEN64_BOARD_REV_B:
+		snprintf(boardmodel, 32, "1064-0201B (Beta)");
+		break;
+	case TEN64_BOARD_REV_C:
+		snprintf(boardmodel, 32, "1064-0201C");
+		break;
+	default:
+		snprintf(boardmodel, 32, "1064 Revision %X", (0xFF - board_rev));
+		break;
+	}
+
+	printf("Board: %s, boot from ", boardmodel);
+	if (src == BOOT_SOURCE_SD_MMC)
+		puts("SD card\n");
+	else if (src == BOOT_SOURCE_QSPI_NOR)
+		puts("QSPI\n");
+	else
+		printf("Unknown boot source %d\n", src);
+
+	puts("Controller: ");
+	if (CONFIG_IS_ENABLED(TEN64_CONTROLLER)) {
+		/* Driver not compatible with alpha/beta board MCU firmware */
+		if (board_rev <= TEN64_BOARD_REV_C) {
+			if (ten64_read_board_info(&boardinfo)) {
+				puts("ERROR: unable to communicate\n");
+			} else {
+				printf("firmware %d.%d.%d\n",
+				       boardinfo.fwversion_major,
+				       boardinfo.fwversion_minor,
+				       boardinfo.fwversion_patch);
+				ten64_set_macaddrs_from_board_info(&boardinfo);
+			}
+		} else {
+			puts("not supported on this board revision\n");
+		}
+	} else {
+		puts("driver not enabled (no MAC addresses or other information will be read)\n");
+	}
+
+	return 0;
+}
+
+int board_init(void)
+{
+	init_final_memctl_regs();
+
+	if (CONFIG_IS_ENABLED(FSL_CAAM))
+		sec_init();
+
+	return 0;
+}
+
+int fsl_initdram(void)
+{
+	gd->ram_size = tfa_get_dram_size();
+
+	if (!gd->ram_size)
+		gd->ram_size = fsl_ddr_sdram_size();
+
+	return 0;
+}
+
+void detail_board_ddr_info(void)
+{
+	puts("\nDDR    ");
+	print_size(gd->bd->bi_dram[0].size + gd->bd->bi_dram[1].size, "");
+	print_ddr_info(0);
+}
+
+void board_quiesce_devices(void)
+{
+	if (IS_ENABLED(CONFIG_FSL_MC_ENET))
+		fsl_mc_ldpaa_exit(gd->bd);
+}
+
+void fdt_fixup_board_enet(void *fdt)
+{
+	int offset;
+
+	offset = fdt_path_offset(fdt, "/fsl-mc");
+
+	if (offset < 0)
+		offset = fdt_path_offset(fdt, "/soc/fsl-mc");
+
+	if (offset < 0) {
+		printf("%s: ERROR: fsl-mc node not found in device tree (error %d)\n",
+		       __func__, offset);
+		return;
+	}
+
+	if (get_mc_boot_status() == 0 &&
+	    (is_lazy_dpl_addr_valid() || get_dpl_apply_status() == 0))
+		fdt_status_okay(fdt, offset);
+	else
+		fdt_status_fail(fdt, offset);
+}
+
+/* Called after SoC board_late_init in fsl-layerscape/soc.c */
+int fsl_board_late_init(void)
+{
+	ten64_board_retimer_ds110df410_init();
+	return 0;
+}
+
+int ft_board_setup(void *blob, struct bd_info *bd)
+{
+	int i;
+	u16 mc_memory_bank = 0;
+
+	u64 *base;
+	u64 *size;
+	u64 mc_memory_base = 0;
+	u64 mc_memory_size = 0;
+	u16 total_memory_banks;
+
+	debug("%s blob=0x%p\n", __func__, blob);
+
+	ft_cpu_setup(blob, bd);
+
+	fdt_fixup_mc_ddr(&mc_memory_base, &mc_memory_size);
+
+	if (mc_memory_base != 0)
+		mc_memory_bank++;
+
+	total_memory_banks = CONFIG_NR_DRAM_BANKS + mc_memory_bank;
+
+	base = calloc(total_memory_banks, sizeof(u64));
+	size = calloc(total_memory_banks, sizeof(u64));
+
+	/* fixup DT for the two GPP DDR banks */
+	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+		base[i] = gd->bd->bi_dram[i].start;
+		size[i] = gd->bd->bi_dram[i].size;
+		/* reduce size if reserved memory is within this bank */
+		if (CONFIG_IS_ENABLED(RESV_RAM) && RESV_MEM_IN_BANK(i))
+			size[i] = gd->arch.resv_ram - base[i];
+	}
+
+	if (mc_memory_base != 0) {
+		for (i = 0; i <= total_memory_banks; i++) {
+			if (base[i] == 0 && size[i] == 0) {
+				base[i] = mc_memory_base;
+				size[i] = mc_memory_size;
+				break;
+			}
+		}
+	}
+
+	fdt_fixup_memory_banks(blob, base, size, total_memory_banks);
+
+	fdt_fsl_mc_fixup_iommu_map_entry(blob);
+
+	if (CONFIG_IS_ENABLED(FSL_MC_ENET))
+		fdt_fixup_board_enet(blob);
+
+	fdt_fixup_icid(blob);
+
+	return 0;
+}
+
+#define MACADDRBITS(a, b) (u8)(((a) >> (b)) & 0xFF)
+
+/** Probe and return a udevice for the Ten64 board microcontroller.
+ * Optionally, return the I2C bus the microcontroller resides on
+ * @i2c_bus_out: return I2C bus device handle in this pointer
+ */
+static int ten64_get_micro_udevice(struct udevice **ucdev, struct udevice **i2c_bus_out)
+{
+	int ret;
+	struct udevice *i2cbus;
+
+	ret = uclass_get_device_by_seq(UCLASS_I2C, 0, &i2cbus);
+	if (ret) {
+		printf("%s: Could not get I2C UCLASS", __func__);
+		return ret;
+	}
+	if (i2c_bus_out)
+		*i2c_bus_out = i2cbus;
+
+	ret = dm_i2c_probe(i2cbus, 0x7E, DM_I2C_CHIP_RD_ADDRESS, ucdev);
+	if (ret) {
+		printf("%s: Could not get microcontroller device\n", __func__);
+		return ret;
+	}
+	return ret;
+}
+
+static int ten64_read_board_info(struct t64uc_board_info *boardinfo)
+{
+	struct udevice *ucdev;
+	int ret;
+
+	ret = ten64_get_micro_udevice(&ucdev, NULL);
+	if (ret)
+		return ret;
+
+	ret = misc_call(ucdev, TEN64_CNTRL_GET_BOARD_INFO, NULL, 0, (void *)boardinfo, 0);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static void ten64_set_macaddrs_from_board_info(struct t64uc_board_info *boardinfo)
+{
+	char ethaddr[18];
+	char enetvar[10];
+	u8 intfidx, this_dpmac_num;
+	u64 macaddr = 0;
+	/* We will copy the MAC address returned from the
+	 * uC (48 bits) into the u64 macaddr
+	 */
+	u8 *macaddr_bytes = (u8 *)&macaddr + 2;
+
+	/** MAC addresses are allocated in order of the physical port numbers,
+	 * DPMAC7->10 is "eth0" through "eth3"
+	 * DPMAC3->6 is "eth4" through "eth7"
+	 * DPMAC2 and 1 are "eth8" and "eth9" respectively
+	 */
+	int allocation_order[10] = {7, 8, 9, 10, 3, 4, 5, 6, 2, 1};
+
+	memcpy(macaddr_bytes, boardinfo->mac, 6);
+	/* MAC address bytes from uC are in big endian,
+	 * convert to CPU
+	 */
+	macaddr = __be64_to_cpu(macaddr);
+
+	for (intfidx = 0; intfidx < 10; intfidx++) {
+		snprintf(ethaddr, 18, "%02X:%02X:%02X:%02X:%02X:%02X",
+			 MACADDRBITS(macaddr, 40),
+			 MACADDRBITS(macaddr, 32),
+			 MACADDRBITS(macaddr, 24),
+			 MACADDRBITS(macaddr, 16),
+			 MACADDRBITS(macaddr, 8),
+			 MACADDRBITS(macaddr, 0));
+
+		this_dpmac_num = allocation_order[intfidx];
+		printf("DPMAC%d: %s\n", this_dpmac_num, ethaddr);
+		snprintf(enetvar, 10,
+			 (this_dpmac_num != 1) ? "eth%daddr" : "ethaddr",
+			 this_dpmac_num - 1);
+		macaddr++;
+
+		if (!env_get(enetvar))
+			env_set(enetvar, ethaddr);
+	}
+}
+
+/* The retimer (DS110DF410) is one of the devices without
+ * a RESET line, but a power switch is on the board
+ * allowing it to be reset via uC command
+ */
+static int board_cycle_retimer(struct udevice **retim_dev)
+{
+	int ret;
+	u8 loop;
+	struct udevice *uc_dev;
+	struct udevice *i2cbus;
+
+	ret = ten64_get_micro_udevice(&uc_dev, &i2cbus);
+	if (ret)
+		return ret;
+
+	ret = dm_i2c_probe(i2cbus, I2C_RETIMER_ADDR, 0, retim_dev);
+	if (ret == 0) {
+		puts("(retimer on, resetting...) ");
+
+		ret = misc_call(uc_dev, TEN64_CNTRL_10G_OFF, NULL, 0, NULL, 0);
+		mdelay(1000);
+	}
+
+	ret = misc_call(uc_dev, TEN64_CNTRL_10G_ON, NULL, 0, NULL, 0);
+
+	// Wait for retimer to come back
+	for (loop = 0; loop < 5; loop++) {
+		ret = dm_i2c_probe(i2cbus, I2C_RETIMER_ADDR, 0, retim_dev);
+		if (ret == 0)
+			return 0;
+		mdelay(500);
+	}
+
+	return -ENOSYS;
+}
+
+/* ten64_board_retimer_ds110df410_init() - Configure the 10G retimer
+ * Adopted from the t102xqds board file
+ */
+static void ten64_board_retimer_ds110df410_init(void)
+{
+	u8 reg;
+	int ret;
+	struct udevice *retim_dev;
+	u32 board_rev = ten64_get_board_rev();
+
+	puts("Retimer: ");
+	/* Retimer power cycle not implemented on early board
+	 * revisions/controller firmwares
+	 */
+	if (CONFIG_IS_ENABLED(TEN64_CONTROLLER) &&
+	    board_rev >= TEN64_BOARD_REV_C) {
+		ret = board_cycle_retimer(&retim_dev);
+		if (ret) {
+			puts("Retimer power on failed\n");
+			return;
+		}
+	}
+
+	/* Access to Control/Shared register */
+	reg = 0x0;
+
+	ret = dm_i2c_write(retim_dev, 0xff, &reg, 1);
+	if (ret) {
+		printf("Error writing to retimer register (error %d)\n", ret);
+		return;
+	}
+
+	/* Read device revision and ID */
+	dm_i2c_read(retim_dev, 1, &reg, 1);
+	if (reg == 0xF0)
+		puts("DS110DF410 found\n");
+	else
+		printf("Unknown retimer 0x%xn\n", reg);
+
+	/* Enable Broadcast */
+	reg = 0x0c;
+	dm_i2c_write(retim_dev, 0xff, &reg, 1);
+
+	/* Perform a full reset (state, channel and clock)
+	 * for all channels
+	 * as the DS110DF410 does not have a RESET line
+	 */
+	dm_i2c_read(retim_dev, 0, &reg, 1);
+	reg |= 0x7;
+	dm_i2c_write(retim_dev, 0, &reg, 1);
+
+	/* Set rate/subrate = 0 */
+	reg = 0x6;
+	dm_i2c_write(retim_dev, 0x2F, &reg, 1);
+
+	/* Set data rate as 10.3125 Gbps */
+	reg = 0x0;
+	dm_i2c_write(retim_dev, 0x60, &reg, 1);
+	reg = 0xb2;
+	dm_i2c_write(retim_dev, 0x61, &reg, 1);
+	reg = 0x90;
+	dm_i2c_write(retim_dev, 0x62, &reg, 1);
+	reg = 0xb3;
+	dm_i2c_write(retim_dev, 0x63, &reg, 1);
+	reg = 0xff;
+	dm_i2c_write(retim_dev, 0x64, &reg, 1);
+
+	/* Invert channel 2 (Lower SFP TX to CPU) due to the SFP being inverted */
+	reg = 0x05;
+	dm_i2c_write(retim_dev, 0xFF, &reg, 1);
+	dm_i2c_read(retim_dev, 0x1F, &reg, 1);
+	reg |= 0x80;
+	dm_i2c_write(retim_dev, 0x1F, &reg, 1);
+
+	puts("OK\n");
+}
diff --git a/configs/T1024RDB_NAND_defconfig b/configs/T1024RDB_NAND_defconfig
index c1d0323..20ded48 100644
--- a/configs/T1024RDB_NAND_defconfig
+++ b/configs/T1024RDB_NAND_defconfig
@@ -96,6 +96,7 @@
 CONFIG_DM_MDIO=y
 CONFIG_E1000=y
 CONFIG_FMAN_ENET=y
+CONFIG_SYS_FMAN_FW_ADDR=0x180000
 CONFIG_MII=y
 CONFIG_PCIE_FSL=y
 CONFIG_SYS_QE_FW_ADDR=0x200000
diff --git a/configs/T1042D4RDB_SDCARD_defconfig b/configs/T1042D4RDB_SDCARD_defconfig
index 94e1528..efb46b3 100644
--- a/configs/T1042D4RDB_SDCARD_defconfig
+++ b/configs/T1042D4RDB_SDCARD_defconfig
@@ -90,6 +90,7 @@
 CONFIG_MII=y
 CONFIG_PCIE_FSL=y
 CONFIG_U_QE=y
+CONFIG_SYS_QE_FW_ADDR=0x124000
 CONFIG_SYS_QE_FMAN_FW_IN_MMC=y
 CONFIG_DM_RTC=y
 CONFIG_SYS_NS16550=y
diff --git a/configs/T2080RDB_defconfig b/configs/T2080RDB_defconfig
index f034403..1e53273 100644
--- a/configs/T2080RDB_defconfig
+++ b/configs/T2080RDB_defconfig
@@ -79,6 +79,7 @@
 CONFIG_DM_MDIO=y
 CONFIG_E1000=y
 CONFIG_FMAN_ENET=y
+CONFIG_SYS_FMAN_FW_ADDR=0xEFF00000
 CONFIG_MII=y
 CONFIG_PCIE_FSL=y
 CONFIG_SYS_QE_FMAN_FW_IN_NOR=y
diff --git a/configs/ls1046ardb_sdcard_SECURE_BOOT_defconfig b/configs/ls1046ardb_sdcard_SECURE_BOOT_defconfig
index 4c55777..4ee9316 100644
--- a/configs/ls1046ardb_sdcard_SECURE_BOOT_defconfig
+++ b/configs/ls1046ardb_sdcard_SECURE_BOOT_defconfig
@@ -80,6 +80,7 @@
 CONFIG_DM_MDIO=y
 CONFIG_E1000=y
 CONFIG_FMAN_ENET=y
+CONFIG_SYS_FMAN_FW_ADDR=0x900000
 CONFIG_PCI=y
 CONFIG_PCIE_LAYERSCAPE_RC=y
 CONFIG_PCIE_LAYERSCAPE_EP=y
diff --git a/configs/pg_wcom_expu1_defconfig b/configs/pg_wcom_expu1_defconfig
index 53d57e0..8238ca8 100644
--- a/configs/pg_wcom_expu1_defconfig
+++ b/configs/pg_wcom_expu1_defconfig
@@ -1,7 +1,10 @@
 CONFIG_ARM=y
 CONFIG_SKIP_LOWLEVEL_INIT=y
 CONFIG_TARGET_PG_WCOM_EXPU1=y
+CONFIG_PG_WCOM_UBOOT_UPDATE_SUPPORTED=y
+CONFIG_PG_WCOM_UBOOT_BOOTPACKAGE=y
 CONFIG_SYS_TEXT_BASE=0x60100000
+CONFIG_PG_WCOM_UBOOT_UPDATE_TEXT_BASE=0x60240000
 CONFIG_SYS_MALLOC_LEN=0x1004000
 CONFIG_NR_DRAM_BANKS=1
 CONFIG_KM_DEF_NETDEV="eth2"
@@ -26,6 +29,9 @@
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_OF_STDOUT_VIA_ALIAS=y
 CONFIG_BOOTDELAY=3
+CONFIG_AUTOBOOT_KEYED=y
+CONFIG_AUTOBOOT_STOP_STR=" "
+CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n"
 CONFIG_USE_BOOTARGS=y
 CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0"
 CONFIG_SILENT_CONSOLE=y
@@ -42,7 +48,7 @@
 CONFIG_CMD_CRAMFS=y
 CONFIG_CMD_MTDPARTS=y
 CONFIG_MTDIDS_DEFAULT="nor0=60000000.nor,nand0=68000000.flash"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:128k(rcw),128k(qe),128k(envred),128k(env),512k(res),1m(u-boot),-(ubi0);68000000.flash:-(ubi1)"
+CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:128k(rcw),128k(qe),128k(envred),128k(env),512k(res),1m(u-boot),128k(redenvred),128k(redenv),1m(redu-boot),-(ubi0);68000000.flash:-(ubi1)"
 CONFIG_CMD_UBI=y
 CONFIG_OF_CONTROL=y
 CONFIG_ENV_OVERWRITE=y
@@ -76,3 +82,4 @@
 CONFIG_SPECIFY_CONSOLE_INDEX=y
 CONFIG_DM_SERIAL=y
 CONFIG_SYS_NS16550=y
+CONFIG_VERSION_VARIABLE=y
diff --git a/configs/pg_wcom_expu1_update_defconfig b/configs/pg_wcom_expu1_update_defconfig
new file mode 100644
index 0000000..0fd5ebc
--- /dev/null
+++ b/configs/pg_wcom_expu1_update_defconfig
@@ -0,0 +1,83 @@
+CONFIG_ARM=y
+CONFIG_SKIP_LOWLEVEL_INIT=y
+CONFIG_TARGET_PG_WCOM_EXPU1=y
+CONFIG_PG_WCOM_UBOOT_UPDATE_SUPPORTED=y
+CONFIG_PG_WCOM_UBOOT_UPDATE=y
+CONFIG_SYS_TEXT_BASE=0x60240000
+CONFIG_SYS_MALLOC_LEN=0x1004000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_KM_DEF_NETDEV="eth2"
+CONFIG_KM_COMMON_ETH_INIT=y
+CONFIG_PIGGY_MAC_ADDRESS_OFFSET=3
+CONFIG_SYS_MEMTEST_START=0x80000000
+CONFIG_SYS_MEMTEST_END=0x9fffffff
+CONFIG_ENV_SIZE=0x4000
+CONFIG_ENV_SECT_SIZE=0x20000
+CONFIG_SYS_I2C_MXC_I2C1=y
+CONFIG_SYS_I2C_MXC_I2C2=y
+CONFIG_SYS_I2C_MXC_I2C3=y
+CONFIG_DEFAULT_DEVICE_TREE="ls1021a-pg-wcom-expu1"
+CONFIG_BOOTCOUNT_BOOTLIMIT=3
+CONFIG_SYS_BOOTCOUNT_ADDR=0x70000020
+CONFIG_AHCI=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_SYS_LOAD_ADDR=0x82000000
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_OF_STDOUT_VIA_ALIAS=y
+CONFIG_BOOTDELAY=3
+CONFIG_AUTOBOOT_KEYED=y
+CONFIG_AUTOBOOT_STOP_STR=" "
+CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n"
+CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0"
+CONFIG_SILENT_CONSOLE=y
+CONFIG_LAST_STAGE_INIT=y
+CONFIG_MISC_INIT_R=y
+CONFIG_CMD_IMLS=y
+CONFIG_CMD_GREPENV=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_NAND=y
+CONFIG_CMD_NAND_TRIMFFS=y
+CONFIG_CMD_CRAMFS=y
+CONFIG_CMD_MTDPARTS=y
+CONFIG_MTDIDS_DEFAULT="nor0=60000000.nor,nand0=68000000.flash"
+CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:128k(rcw),128k(qe),128k(envred),128k(env),512k(res),1m(u-boot),128k(redenvred),128k(redenv),1m(redu-boot),-(ubi0);68000000.flash:-(ubi1)"
+CONFIG_CMD_UBI=y
+CONFIG_OF_CONTROL=y
+CONFIG_ENV_OVERWRITE=y
+CONFIG_ENV_IS_IN_FLASH=y
+CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
+CONFIG_ENV_ADDR=0x60220000
+CONFIG_ENV_ADDR_REDUND=0x60200000
+CONFIG_DM=y
+CONFIG_BOOTCOUNT_LIMIT=y
+CONFIG_DDR_CLK_FREQ=50000000
+CONFIG_SYS_FSL_DDR3=y
+CONFIG_SYS_I2C_LEGACY=y
+# CONFIG_MMC is not set
+CONFIG_MTD=y
+CONFIG_MTD_NOR_FLASH=y
+CONFIG_FLASH_CFI_DRIVER=y
+CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
+CONFIG_FLASH_CFI_MTD=y
+CONFIG_SYS_FLASH_CFI=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_NAND_FSL_IFC=y
+CONFIG_SYS_NAND_ONFI_DETECTION=y
+CONFIG_PHY_MARVELL=y
+CONFIG_PHY_FIXED=y
+CONFIG_DM_ETH=y
+CONFIG_DM_MDIO=y
+CONFIG_PHY_GIGE=y
+CONFIG_MII=y
+CONFIG_TSEC_ENET=y
+CONFIG_SYS_QE_FW_ADDR=0x60020000
+CONFIG_SPECIFY_CONSOLE_INDEX=y
+CONFIG_DM_SERIAL=y
+CONFIG_SYS_NS16550=y
+CONFIG_VERSION_VARIABLE=y
diff --git a/configs/pg_wcom_seli8_defconfig b/configs/pg_wcom_seli8_defconfig
index 3eaf7fd..229535c 100644
--- a/configs/pg_wcom_seli8_defconfig
+++ b/configs/pg_wcom_seli8_defconfig
@@ -1,7 +1,10 @@
 CONFIG_ARM=y
 CONFIG_SKIP_LOWLEVEL_INIT=y
 CONFIG_TARGET_PG_WCOM_SELI8=y
+CONFIG_PG_WCOM_UBOOT_UPDATE_SUPPORTED=y
+CONFIG_PG_WCOM_UBOOT_BOOTPACKAGE=y
 CONFIG_SYS_TEXT_BASE=0x60100000
+CONFIG_PG_WCOM_UBOOT_UPDATE_TEXT_BASE=0x60240000
 CONFIG_SYS_MALLOC_LEN=0x1004000
 CONFIG_NR_DRAM_BANKS=1
 CONFIG_KM_DEF_NETDEV="eth2"
@@ -26,6 +29,9 @@
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_OF_STDOUT_VIA_ALIAS=y
 CONFIG_BOOTDELAY=3
+CONFIG_AUTOBOOT_KEYED=y
+CONFIG_AUTOBOOT_STOP_STR=" "
+CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n"
 CONFIG_USE_BOOTARGS=y
 CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0"
 CONFIG_SILENT_CONSOLE=y
@@ -42,7 +48,7 @@
 CONFIG_CMD_CRAMFS=y
 CONFIG_CMD_MTDPARTS=y
 CONFIG_MTDIDS_DEFAULT="nor0=60000000.nor,nand0=68000000.flash"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:128k(rcw),128k(qe),128k(envred),128k(env),512k(res),1m(u-boot),-(ubi0);68000000.flash:-(ubi1)"
+CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:128k(rcw),128k(qe),128k(envred),128k(env),512k(res),1m(u-boot),128k(redenvred),128k(redenv),1m(redu-boot),-(ubi0);68000000.flash:-(ubi1)"
 CONFIG_CMD_UBI=y
 CONFIG_OF_CONTROL=y
 CONFIG_ENV_OVERWRITE=y
@@ -76,3 +82,4 @@
 CONFIG_SPECIFY_CONSOLE_INDEX=y
 CONFIG_DM_SERIAL=y
 CONFIG_SYS_NS16550=y
+CONFIG_VERSION_VARIABLE=y
diff --git a/configs/pg_wcom_seli8_update_defconfig b/configs/pg_wcom_seli8_update_defconfig
new file mode 100644
index 0000000..fb5b715
--- /dev/null
+++ b/configs/pg_wcom_seli8_update_defconfig
@@ -0,0 +1,83 @@
+CONFIG_ARM=y
+CONFIG_SKIP_LOWLEVEL_INIT=y
+CONFIG_TARGET_PG_WCOM_SELI8=y
+CONFIG_PG_WCOM_UBOOT_UPDATE_SUPPORTED=y
+CONFIG_PG_WCOM_UBOOT_UPDATE=y
+CONFIG_SYS_TEXT_BASE=0x60240000
+CONFIG_SYS_MALLOC_LEN=0x1004000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_KM_DEF_NETDEV="eth2"
+CONFIG_KM_COMMON_ETH_INIT=y
+CONFIG_PIGGY_MAC_ADDRESS_OFFSET=3
+CONFIG_SYS_MEMTEST_START=0x80000000
+CONFIG_SYS_MEMTEST_END=0x9fffffff
+CONFIG_ENV_SIZE=0x4000
+CONFIG_ENV_SECT_SIZE=0x20000
+CONFIG_SYS_I2C_MXC_I2C1=y
+CONFIG_SYS_I2C_MXC_I2C2=y
+CONFIG_SYS_I2C_MXC_I2C3=y
+CONFIG_DEFAULT_DEVICE_TREE="ls1021a-pg-wcom-seli8"
+CONFIG_BOOTCOUNT_BOOTLIMIT=3
+CONFIG_SYS_BOOTCOUNT_ADDR=0x70000020
+CONFIG_AHCI=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_SYS_LOAD_ADDR=0x82000000
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_OF_STDOUT_VIA_ALIAS=y
+CONFIG_BOOTDELAY=3
+CONFIG_AUTOBOOT_KEYED=y
+CONFIG_AUTOBOOT_STOP_STR=" "
+CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n"
+CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0"
+CONFIG_SILENT_CONSOLE=y
+CONFIG_LAST_STAGE_INIT=y
+CONFIG_MISC_INIT_R=y
+CONFIG_CMD_IMLS=y
+CONFIG_CMD_GREPENV=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_NAND=y
+CONFIG_CMD_NAND_TRIMFFS=y
+CONFIG_CMD_CRAMFS=y
+CONFIG_CMD_MTDPARTS=y
+CONFIG_MTDIDS_DEFAULT="nor0=60000000.nor,nand0=68000000.flash"
+CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:128k(rcw),128k(qe),128k(envred),128k(env),512k(res),1m(u-boot),128k(redenvred),128k(redenv),1m(redu-boot),-(ubi0);68000000.flash:-(ubi1)"
+CONFIG_CMD_UBI=y
+CONFIG_OF_CONTROL=y
+CONFIG_ENV_OVERWRITE=y
+CONFIG_ENV_IS_IN_FLASH=y
+CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
+CONFIG_ENV_ADDR=0x60220000
+CONFIG_ENV_ADDR_REDUND=0x60200000
+CONFIG_DM=y
+CONFIG_BOOTCOUNT_LIMIT=y
+CONFIG_DDR_CLK_FREQ=50000000
+CONFIG_SYS_FSL_DDR3=y
+CONFIG_SYS_I2C_LEGACY=y
+# CONFIG_MMC is not set
+CONFIG_MTD=y
+CONFIG_MTD_NOR_FLASH=y
+CONFIG_FLASH_CFI_DRIVER=y
+CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
+CONFIG_FLASH_CFI_MTD=y
+CONFIG_SYS_FLASH_CFI=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_NAND_FSL_IFC=y
+CONFIG_SYS_NAND_ONFI_DETECTION=y
+CONFIG_PHY_MARVELL=y
+CONFIG_PHY_FIXED=y
+CONFIG_DM_ETH=y
+CONFIG_DM_MDIO=y
+CONFIG_PHY_GIGE=y
+CONFIG_MII=y
+CONFIG_TSEC_ENET=y
+CONFIG_SYS_QE_FW_ADDR=0x60020000
+CONFIG_SPECIFY_CONSOLE_INDEX=y
+CONFIG_DM_SERIAL=y
+CONFIG_SYS_NS16550=y
+CONFIG_VERSION_VARIABLE=y
diff --git a/configs/ten64_tfa_defconfig b/configs/ten64_tfa_defconfig
new file mode 100644
index 0000000..8d45b13
--- /dev/null
+++ b/configs/ten64_tfa_defconfig
@@ -0,0 +1,119 @@
+CONFIG_ARM=y
+CONFIG_TARGET_TEN64=y
+CONFIG_SYS_TEXT_BASE=0x82000000
+CONFIG_QSPI_AHB_INIT=y
+CONFIG_TFABOOT=y
+CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y
+CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_NR_DRAM_BANKS=2
+# CONFIG_SYS_MALLOC_F is not set
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_OF_FDT_OVERLAY=y
+CONFIG_OF_STDOUT_VIA_ALIAS=y
+CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4"
+CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 ramdisk_size=0x3000000 default_hugepagesz=2m hugepagesz=2m hugepages=256"
+# CONFIG_USE_BOOTCOMMAND is not set
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_CMD_BOOTEFI_HELLO=y
+CONFIG_CMD_BOOTEFI_SELFTEST=y
+CONFIG_CMD_BOOTMENU=y
+CONFIG_CMD_GPT=y
+CONFIG_RANDOM_UUID=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GREPENV=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_UBI=y
+CONFIG_CMD_UBIFS=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_POWEROFF=y
+CONFIG_CMD_WDT=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_FS_FAT=y
+CONFIG_FAT_WRITE=y
+CONFIG_MP=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1088a-ten64"
+CONFIG_EMC230X=y
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_ENV_OFFSET=0x500000
+CONFIG_ENV_SIZE=0x80000
+CONFIG_ENV_SECT_SIZE=0x80000
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM=y
+CONFIG_SCSI_AHCI=y
+CONFIG_DM_MMC=y
+CONFIG_FSL_ESDHC=y
+CONFIG_CMD_FAN=y
+CONFIG_FANCONTROL=y
+CONFIG_DM_MTD=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_EON=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_E1000=y
+# CONFIG_ID_EEPROM is not set
+CONFIG_MII=y
+CONFIG_NVME=y
+CONFIG_CMD_PCI=y
+CONFIG_PCI=y
+CONFIG_DM_PCA953X=y
+CONFIG_DM_PCI=y
+CONFIG_DM_PCI_COMPAT=y
+CONFIG_PCIE_LAYERSCAPE_RC=y
+CONFIG_SYS_NS16550=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_FSL_DSPI=y
+CONFIG_FSL_QSPI=y
+CONFIG_UBI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_GADGET=y
+CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
+CONFIG_DM_I2C=y
+CONFIG_DM_GPIO=y
+CONFIG_ARM_SMCCC=y
+CONFIG_MTD=y
+CONFIG_MTD_SPI_NAND=y
+CONFIG_CMD_MTD=y
+CONFIG_LOGLEVEL=7
+CONFIG_MTDPARTS_DEFAULT="mtdparts=spi-nand0:8m(reserved),32m(recovery),108m(ubia),108m(ubib);nor1:1m(bl2),2m(bl3),2m(mcfirmware),512k(ubootenv),256k(dpl),256k(dpc),256k(devicetree)"
+CONFIG_MPC8XXX_GPIO=y
+CONFIG_GPIO_HOG=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_RX8025=y
+CONFIG_CMD_NVEDIT_EFI=y
+CONFIG_CMD_EFIDEBUG=y
+CONFIG_DM_ETH=y
+CONFIG_PCI_INIT_R=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_VITESSE=y
+CONFIG_DM_MDIO=y
+CONFIG_FSL_LS_MDIO=y
+CONFIG_SYS_MALLOC_F=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_TPM=y
+CONFIG_CMD_TPM=y
+CONFIG_TPM_ATMEL_TWI=y
+CONFIG_MISC=y
+CONFIG_USB5744=y
+CONFIG_TEN64_CONTROLLER=y
+CONFIG_DM_SCSI=y
+CONFIG_AHCI=y
+CONFIG_AHCI_PCI=y
+CONFIG_WDT=y
+CONFIG_WDT_SP805=y
diff --git a/drivers/i2c/muxes/pca954x.c b/drivers/i2c/muxes/pca954x.c
index 55858cf..0034dfb 100644
--- a/drivers/i2c/muxes/pca954x.c
+++ b/drivers/i2c/muxes/pca954x.c
@@ -23,7 +23,8 @@
 	PCA9546,
 	PCA9547,
 	PCA9548,
-	PCA9646
+	PCA9646,
+	PCA9847,
 };
 
 struct chip_desc {
@@ -68,6 +69,11 @@
 		.muxtype = pca954x_isswi,
 		.width = 4,
 	},
+	[PCA9847] = {
+		.enable = 0x8,
+		.muxtype = pca954x_ismux,
+		.width = 8,
+	},
 };
 
 static int pca954x_deselect(struct udevice *mux, struct udevice *bus,
@@ -106,6 +112,7 @@
 	{ .compatible = "nxp,pca9547", .data = PCA9547 },
 	{ .compatible = "nxp,pca9548", .data = PCA9548 },
 	{ .compatible = "nxp,pca9646", .data = PCA9646 },
+	{ .compatible = "nxp,pca9847", .data = PCA9847 },
 	{ }
 };
 
diff --git a/drivers/pci/Kconfig b/drivers/pci/Kconfig
index 6914134..47cd074 100644
--- a/drivers/pci/Kconfig
+++ b/drivers/pci/Kconfig
@@ -233,8 +233,7 @@
 	default "fsl,ls1046a-pcie" if ARCH_LS1046A
 	default "fsl,ls2080a-pcie" if ARCH_LS2080A
 	default "fsl,ls1088a-pcie" if ARCH_LS1088A
-	default "fsl,lx2160a-pcie" if ARCH_LX2160A
-	default "fsl,ls2088a-pcie" if ARCH_LX2162A
+	default "fsl,ls2088a-pcie" if ARCH_LX2160A || ARCH_LX2162A
 	default "fsl,ls1021a-pcie" if ARCH_LS1021A
 	help
 	  This compatible is used to find pci controller node in Kernel DT
@@ -243,7 +242,6 @@
 config FSL_PCIE_EP_COMPAT
 	string "PCIe EP compatible of Kernel DT"
 	depends on PCIE_LAYERSCAPE_RC || PCIE_LAYERSCAPE_GEN4
-	default "fsl,lx2160a-pcie-ep" if ARCH_LX2160A
 	default "fsl,ls-pcie-ep"
 	help
 	  This compatible is used to find pci controller ep node in Kernel DT
diff --git a/drivers/pci/pcie_layerscape_fixup.c b/drivers/pci/pcie_layerscape_fixup.c
index a47c9ef..c519835 100644
--- a/drivers/pci/pcie_layerscape_fixup.c
+++ b/drivers/pci/pcie_layerscape_fixup.c
@@ -527,7 +527,7 @@
 	}
 
 	if (!IS_ENABLED(CONFIG_PCI_IOMMU_EXTRA_MAPPINGS))
-		goto skip;
+		return;
 
 	list_for_each_entry(pcie_rc, &ls_pcie_list, list) {
 		nodeoffset = fdt_pcie_get_nodeoffset(blob, pcie_rc);
@@ -568,9 +568,6 @@
 		}
 		free(entries);
 	}
-
-skip:
-	pcie_board_fix_fdt(blob);
 }
 #endif
 
@@ -619,6 +616,10 @@
 {
 	struct ls_pcie_rc *pcie_rc;
 
+#if defined(CONFIG_FSL_LSCH3) || defined(CONFIG_FSL_LSCH2)
+	pcie_board_fix_fdt(blob);
+#endif
+
 	list_for_each_entry(pcie_rc, &ls_pcie_list, list)
 		ft_pcie_ls_setup(blob, pcie_rc);
 
diff --git a/drivers/rtc/pcf2127.c b/drivers/rtc/pcf2127.c
index 57f8640..2f3fafb 100644
--- a/drivers/rtc/pcf2127.c
+++ b/drivers/rtc/pcf2127.c
@@ -120,7 +120,9 @@
 };
 
 static const struct udevice_id pcf2127_rtc_ids[] = {
-	{ .compatible = "pcf2127-rtc" },
+	{ .compatible = "nxp,pcf2127" },
+	{ .compatible = "nxp,pcf2129" },
+	{ .compatible = "nxp,pca2129" },
 	{ }
 };
 
diff --git a/include/configs/km/pg-wcom-ls102xa.h b/include/configs/km/pg-wcom-ls102xa.h
index 9d7a9e1..8453be8 100644
--- a/include/configs/km/pg-wcom-ls102xa.h
+++ b/include/configs/km/pg-wcom-ls102xa.h
@@ -274,4 +274,6 @@
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20) /* Increase max gunzip size */
 #define CONFIG_SYS_BOOTMAPSZ	(256 << 20) /* Increase map for Linux */
 
+#define CONFIG_MISC_INIT_F
+
 #endif
diff --git a/include/configs/ten64.h b/include/configs/ten64.h
new file mode 100644
index 0000000..54e65f2
--- /dev/null
+++ b/include/configs/ten64.h
@@ -0,0 +1,55 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2017 NXP
+ * Copyright 2019-2021 Traverse Technologies
+ */
+
+#ifndef __TEN64_H
+#define __TEN64_H
+
+#include "ls1088a_common.h"
+
+#define CONFIG_SYS_CLK_FREQ		100000000
+#define COUNTER_FREQUENCY		25000000	/* 25MHz */
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+
+#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
+
+#define QSPI_NOR_BOOTCOMMAND	"run distro_bootcmd"
+#define SD_BOOTCOMMAND		"run distro_bootcmd"
+
+#define QSPI_MC_INIT_CMD				\
+	"sf probe 0:0 && sf read 0x80000000 0x300000 0x200000 &&"	\
+	"sf read 0x80200000 0x5C0000 0x40000 &&"				\
+	"fsl_mc start mc 0x80000000 0x80200000 && " \
+	"sf read 0x80300000 0x580000 0x40000 && fsl_mc lazyapply DPL 0x80300000\0"
+#define SD_MC_INIT_CMD				\
+	"mmcinfo; fatload mmc 0 0x80000000 mcfirmware/mc_ls1088a.itb; "\
+	"fatload mmc 0 0x80200000 dpaa2config/dpc.0x1D-0x0D.dtb; "\
+	"fsl_mc start mc 0x80000000 0x80200000\0"
+
+#define BOOT_TARGET_DEVICES(func) \
+	func(NVME, nvme, 0) \
+	func(USB, usb, 0) \
+	func(MMC, mmc, 0) \
+	func(SCSI, scsi, 0) \
+	func(DHCP, dhcp, 0) \
+	func(PXE, pxe, 0)
+#include <config_distro_bootcmd.h>
+
+#undef CONFIG_EXTRA_ENV_SETTINGS
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"BOARD=ten64\0"					\
+	"fdt_addr_r=0x90000000\0"		\
+	"fdt_high=0xa0000000\0"			\
+	"kernel_addr_r=0x81000000\0"		\
+	"load_addr=0xa0000000\0"		\
+	BOOTENV \
+	"load_efi_dtb=mtd read devicetree $fdt_addr_r && fdt addr $fdt_addr_r && " \
+	"fdt resize && fdt boardsetup\0" \
+	"bootcmd_recovery=mtd read recovery 0xa0000000; mtd read dpl 0x80100000 && " \
+	"fsl_mc apply DPL 0x80100000 && bootm 0xa0000000#ten64\0"
+
+#endif /* __TEN64_H */