arch/arm/dts/rk3399-puma-haikou-u-boot.dtsi

// SPDX-License-Identifier: GPL-2.0+

#include "rk3399-u-boot.dtsi"

#ifdef CONFIG_TARGET_PUMA_RK3399_RAM_DDR3_1333
#include "rk3399-sdram-ddr3-1333.dtsi"
#endif
#ifdef CONFIG_TARGET_PUMA_RK3399_RAM_DDR3_1600
#include "rk3399-sdram-ddr3-1600.dtsi"
#endif
#ifdef CONFIG_TARGET_PUMA_RK3399_RAM_DDR3_1866
#include "rk3399-sdram-ddr3-1866.dtsi"
#endif

/ {
	config {
		u-boot,spl-payload-offset = <0x80000>; /* @ 512KB */
		u-boot,mmc-env-offset = <0x4000>;      /* @  16KB */
		u-boot,efi-partition-entries-offset = <0x200000>; /* 2MB */
		u-boot,boot-led = "module_led";
		sysreset-gpio = <&gpio1 RK_PA6 GPIO_ACTIVE_HIGH>;
	};

	chosen {
		stdout-path = "serial0:115200n8";
		u-boot,spl-boot-order = \
			"same-as-spl", &norflash, &sdhci, &sdmmc;
	};

	aliases {
		spi5 = &spi5;
	};

	vdd_log: vdd-log {
		compatible = "pwm-regulator";
		pwms = <&pwm2 0 25000 1>;
		regulator-name = "vdd_log";
		regulator-always-on;
		regulator-boot-on;
		regulator-min-microvolt = <800000>;
		regulator-max-microvolt = <1400000>;
		regulator-init-microvolt = <950000>;
		vin-supply = <&vcc5v0_sys>;
	};
};

&binman {
	simple-bin {
		blob {
			offset = <((CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR - 64) * 512)>;
		};
	};
};

&gpio1 {
	u-boot,dm-pre-reloc;
};

&gpio3 {
	u-boot,dm-pre-reloc;

	/*
	 * The Qseven BIOS_DISABLE signal on the RK3399-Q7 keeps the on-module
	 * eMMC and SPI flash powered-down initially (in fact it keeps the
	 * reset signal asserted). BIOS_DISABLE_OVERRIDE pin allows to re-enable
	 * eMMC and SPI after the SPL has been booted from SD Card.
	 */
	bios_disable_override {
		u-boot,dm-pre-reloc;
		gpios = <RK_PD5 GPIO_ACTIVE_LOW>;
		output-high;
		line-name = "bios_disable_override";
		gpio-hog;
	};
};

&gpio4 {
	u-boot,dm-pre-reloc;
};

&norflash {
	u-boot,dm-pre-reloc;
};

&pcfg_pull_none {
	u-boot,dm-pre-reloc;
};

&pcfg_pull_up {
	u-boot,dm-pre-reloc;
};

&sdmmc_bus4 {
	u-boot,dm-pre-reloc;
};

&sdmmc_clk {
	u-boot,dm-pre-reloc;
};

&sdmmc_cmd {
	u-boot,dm-pre-reloc;
};