diff --git a/arch/arm/dts/dra76-evm.dts b/arch/arm/dts/dra76-evm.dts
index b024a65..a1f289f 100644
--- a/arch/arm/dts/dra76-evm.dts
+++ b/arch/arm/dts/dra76-evm.dts
@@ -9,6 +9,7 @@
 
 #include "dra76x.dtsi"
 #include "dra7-evm-common.dtsi"
+#include "dra76x-mmc-iodelay.dtsi"
 #include <dt-bindings/net/ti-dp83867.h>
 
 / {
@@ -100,46 +101,6 @@
 	};
 };
 
-&dra7_pmx_core {
-	mmc1_pins_default: mmc1_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14)	/* mmc1sdcd.gpio219 */
-			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
-			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
-			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
-			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
-			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
-			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
-		>;
-	};
-
-	mmc1_pins_sdr12: pinmux_mmc1_sdr12_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_clk.clk */
-			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_cmd.cmd */
-			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat0.dat0 */
-			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat1.dat1 */
-			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat2.dat2 */
-			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat3.dat3 */
-		>;
-	};
-
-	mmc2_pins_default: mmc2_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
-			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
-			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
-			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
-			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
-			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
-			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
-			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
-			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
-			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
-		>;
-	};
-};
-
 &i2c1 {
 	status = "okay";
 	clock-frequency = <400000>;
@@ -345,23 +306,27 @@
 &mmc1 {
 	status = "okay";
 	vmmc-supply = <&vio_3v3_sd>;
-	vmmc_aux-supply = <&ldo4_reg>;
+	vqmmc-supply = <&ldo4_reg>;
 	bus-width = <4>;
 	/*
 	 * SDCD signal is not being used here - using the fact that GPIO mode
 	 * is always hardwired.
 	 */
 	cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "hs";
 	pinctrl-0 = <&mmc1_pins_default>;
+	pinctrl-1 = <&mmc1_pins_hs>;
 };
 
 &mmc2 {
 	status = "okay";
 	vmmc-supply = <&vio_1v8>;
 	bus-width = <8>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "hs", "ddr_1_8v", "hs200_1_8v";
 	pinctrl-0 = <&mmc2_pins_default>;
+	pinctrl-1 = <&mmc2_pins_default>;
+	pinctrl-2 = <&mmc2_pins_default>;
+	pinctrl-3 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_conf>;
 };
 
 /* No RTC on this device */