diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
index 01c4e16..6e5e0ff 100644
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -52,15 +52,6 @@
 	select SUPPORTS_CPU_MIPS32_R2
 	select SYS_MIPS_CACHE_INIT_RAM_LOAD
 
-config TARGET_PB1X00
-	bool "Support pb1x00"
-	select MIPS_TUNE_4KC
-	select ROM_EXCEPTION_VECTORS
-	select SUPPORTS_CPU_MIPS32_R1
-	select SUPPORTS_CPU_MIPS32_R2
-	select SUPPORTS_LITTLE_ENDIAN
-	select SYS_MIPS_CACHE_INIT_RAM_LOAD
-
 config ARCH_ATH79
 	bool "Support QCA/Atheros ath79"
 	select DM
@@ -125,7 +116,6 @@
 source "board/imgtec/malta/Kconfig"
 source "board/imgtec/xilfpga/Kconfig"
 source "board/micronas/vct/Kconfig"
-source "board/pb1x00/Kconfig"
 source "board/qemu-mips/Kconfig"
 source "arch/mips/mach-ath79/Kconfig"
 source "arch/mips/mach-bmips/Kconfig"
diff --git a/arch/mips/Makefile b/arch/mips/Makefile
index 5deec9a..a36f5f1 100644
--- a/arch/mips/Makefile
+++ b/arch/mips/Makefile
@@ -11,7 +11,6 @@
 libs-y += arch/mips/cpu/
 libs-y += arch/mips/lib/
 
-machine-$(CONFIG_SOC_AU1X00) += au1x00
 machine-$(CONFIG_ARCH_ATH79) += ath79
 machine-$(CONFIG_ARCH_BMIPS) += bmips
 machine-$(CONFIG_MACH_PIC32) += pic32
diff --git a/arch/mips/include/asm/addrspace.h b/arch/mips/include/asm/addrspace.h
index 7deb516..b6d3876 100644
--- a/arch/mips/include/asm/addrspace.h
+++ b/arch/mips/include/asm/addrspace.h
@@ -130,13 +130,13 @@
  * Returns the uncached address of a sdram address
  */
 #ifndef __ASSEMBLY__
-#if defined(CONFIG_SOC_AU1X00) || defined(CONFIG_TB0229)
+#if defined(CONFIG_TB0229)
 /* We use a 36 bit physical address map here and
    cannot access physical memory directly from core */
 #define UNCACHED_SDRAM(a) (((unsigned long)(a)) | 0x20000000)
-#else	/* !CONFIG_SOC_AU1X00 */
+#else	/* !CONFIG_TB0229 */
 #define UNCACHED_SDRAM(a) CKSEG1ADDR(a)
-#endif	/* CONFIG_SOC_AU1X00 */
+#endif	/* CONFIG_TB0229 */
 #endif	/* __ASSEMBLY__ */
 
 /*
diff --git a/arch/mips/mach-au1x00/Makefile b/arch/mips/mach-au1x00/Makefile
deleted file mode 100644
index 4301b9c..0000000
--- a/arch/mips/mach-au1x00/Makefile
+++ /dev/null
@@ -1,6 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2011
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-
-obj-y	= au1x00_eth.o au1x00_serial.o au1x00_usb_ohci.o au1x00_ide.o
diff --git a/arch/mips/mach-au1x00/au1x00_eth.c b/arch/mips/mach-au1x00/au1x00_eth.c
deleted file mode 100644
index ef9be89..0000000
--- a/arch/mips/mach-au1x00/au1x00_eth.c
+++ /dev/null
@@ -1,307 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/* Only eth0 supported for now
- *
- * (C) Copyright 2003
- * Thomas.Lange@corelatus.se
- */
-#include <config.h>
-
-#if defined(CONFIG_SYS_DISCOVER_PHY)
-#error "PHY not supported yet"
-/* We just assume that we are running 100FD for now */
-/* We all use switches, right? ;-) */
-#endif
-
-/* I assume ethernet behaves like au1000 */
-
-#ifdef CONFIG_SOC_AU1000
-/* Base address differ between cpu:s */
-#define ETH0_BASE AU1000_ETH0_BASE
-#define MAC0_ENABLE AU1000_MAC0_ENABLE
-#else
-#ifdef CONFIG_SOC_AU1100
-#define ETH0_BASE AU1100_ETH0_BASE
-#define MAC0_ENABLE AU1100_MAC0_ENABLE
-#else
-#ifdef CONFIG_SOC_AU1500
-#define ETH0_BASE AU1500_ETH0_BASE
-#define MAC0_ENABLE AU1500_MAC0_ENABLE
-#else
-#error "No valid cpu set"
-#endif
-#endif
-#endif
-
-#include <common.h>
-#include <malloc.h>
-#include <net.h>
-#include <command.h>
-#include <asm/io.h>
-#include <mach/au1x00.h>
-
-#if defined(CONFIG_CMD_MII)
-#include <miiphy.h>
-#endif
-
-/* Ethernet Transmit and Receive Buffers */
-#define DBUF_LENGTH  1520
-#define PKT_MAXBUF_SIZE		1518
-
-static char txbuf[DBUF_LENGTH];
-
-static int next_tx;
-static int next_rx;
-
-/* 4 rx and 4 tx fifos */
-#define NO_OF_FIFOS 4
-
-typedef struct{
-	u32 status;
-	u32 addr;
-	u32 len; /* Only used for tx */
-	u32 not_used;
-} mac_fifo_t;
-
-mac_fifo_t mac_fifo[NO_OF_FIFOS];
-
-#define MAX_WAIT 1000
-
-#if defined(CONFIG_CMD_MII)
-int au1x00_miiphy_read(struct mii_dev *bus, int addr, int devad, int reg)
-{
-	unsigned short value = 0;
-	volatile u32 *mii_control_reg = (volatile u32*)(ETH0_BASE+MAC_MII_CNTRL);
-	volatile u32 *mii_data_reg = (volatile u32*)(ETH0_BASE+MAC_MII_DATA);
-	u32 mii_control;
-	unsigned int timedout = 20;
-
-	while (*mii_control_reg & MAC_MII_BUSY) {
-		udelay(1000);
-		if (--timedout == 0) {
-			printf("au1x00_eth: miiphy_read busy timeout!!\n");
-			return -1;
-		}
-	}
-
-	mii_control = MAC_SET_MII_SELECT_REG(reg) |
-		MAC_SET_MII_SELECT_PHY(addr) | MAC_MII_READ;
-
-	*mii_control_reg = mii_control;
-
-	timedout = 20;
-	while (*mii_control_reg & MAC_MII_BUSY) {
-		udelay(1000);
-		if (--timedout == 0) {
-			printf("au1x00_eth: miiphy_read busy timeout!!\n");
-			return -1;
-		}
-	}
-	value = *mii_data_reg;
-	return value;
-}
-
-int au1x00_miiphy_write(struct mii_dev *bus, int addr, int devad, int reg,
-			u16 value)
-{
-	volatile u32 *mii_control_reg = (volatile u32*)(ETH0_BASE+MAC_MII_CNTRL);
-	volatile u32 *mii_data_reg = (volatile u32*)(ETH0_BASE+MAC_MII_DATA);
-	u32 mii_control;
-	unsigned int timedout = 20;
-
-	while (*mii_control_reg & MAC_MII_BUSY) {
-		udelay(1000);
-		if (--timedout == 0) {
-			printf("au1x00_eth: miiphy_write busy timeout!!\n");
-			return -1;
-		}
-	}
-
-	mii_control = MAC_SET_MII_SELECT_REG(reg) |
-		MAC_SET_MII_SELECT_PHY(addr) | MAC_MII_WRITE;
-
-	*mii_data_reg = value;
-	*mii_control_reg = mii_control;
-	return 0;
-}
-#endif
-
-static int au1x00_send(struct eth_device *dev, void *packet, int length)
-{
-	volatile mac_fifo_t *fifo_tx =
-		(volatile mac_fifo_t*)(MAC0_TX_DMA_ADDR+MAC_TX_BUFF0_STATUS);
-	int i;
-	int res;
-
-	/* tx fifo should always be idle */
-	fifo_tx[next_tx].len = length;
-	fifo_tx[next_tx].addr = (virt_to_phys(packet))|TX_DMA_ENABLE;
-	au_sync();
-
-	udelay(1);
-	i=0;
-	while(!(fifo_tx[next_tx].addr&TX_T_DONE)){
-		if(i>MAX_WAIT){
-			printf("TX timeout\n");
-			break;
-		}
-		udelay(1);
-		i++;
-	}
-
-	/* Clear done bit */
-	fifo_tx[next_tx].addr = 0;
-	fifo_tx[next_tx].len = 0;
-	au_sync();
-
-	res = fifo_tx[next_tx].status;
-
-	next_tx++;
-	if(next_tx>=NO_OF_FIFOS){
-		next_tx=0;
-	}
-	return(res);
-}
-
-static int au1x00_recv(struct eth_device* dev){
-	volatile mac_fifo_t *fifo_rx =
-		(volatile mac_fifo_t*)(MAC0_RX_DMA_ADDR+MAC_RX_BUFF0_STATUS);
-
-	int length;
-	u32 status;
-
-	for(;;){
-		if(!(fifo_rx[next_rx].addr&RX_T_DONE)){
-			/* Nothing has been received */
-			return(-1);
-		}
-
-		status = fifo_rx[next_rx].status;
-
-		length = status&0x3FFF;
-
-		if(status&RX_ERROR){
-			printf("Rx error 0x%x\n", status);
-		} else {
-			/* Pass the packet up to the protocol layers. */
-			net_process_received_packet(net_rx_packets[next_rx],
-						    length - 4);
-		}
-
-		fifo_rx[next_rx].addr =
-			(virt_to_phys(net_rx_packets[next_rx])) | RX_DMA_ENABLE;
-
-		next_rx++;
-		if(next_rx>=NO_OF_FIFOS){
-			next_rx=0;
-		}
-	} /* for */
-
-	return(0); /* Does anyone use this? */
-}
-
-static int au1x00_init(struct eth_device* dev, bd_t * bd){
-
-	volatile u32 *macen = (volatile u32*)MAC0_ENABLE;
-	volatile u32 *mac_ctrl = (volatile u32*)(ETH0_BASE+MAC_CONTROL);
-	volatile u32 *mac_addr_high = (volatile u32*)(ETH0_BASE+MAC_ADDRESS_HIGH);
-	volatile u32 *mac_addr_low = (volatile u32*)(ETH0_BASE+MAC_ADDRESS_LOW);
-	volatile u32 *mac_mcast_high = (volatile u32*)(ETH0_BASE+MAC_MCAST_HIGH);
-	volatile u32 *mac_mcast_low = (volatile u32*)(ETH0_BASE+MAC_MCAST_LOW);
-	volatile mac_fifo_t *fifo_tx =
-		(volatile mac_fifo_t*)(MAC0_TX_DMA_ADDR+MAC_TX_BUFF0_STATUS);
-	volatile mac_fifo_t *fifo_rx =
-		(volatile mac_fifo_t*)(MAC0_RX_DMA_ADDR+MAC_RX_BUFF0_STATUS);
-	int i;
-
-	next_tx = TX_GET_DMA_BUFFER(fifo_tx[0].addr);
-	next_rx = RX_GET_DMA_BUFFER(fifo_rx[0].addr);
-
-	/* We have to enable clocks before releasing reset */
-	*macen = MAC_EN_CLOCK_ENABLE;
-	udelay(10);
-
-	/* Enable MAC0 */
-	/* We have to release reset before accessing registers */
-	*macen = MAC_EN_CLOCK_ENABLE|MAC_EN_RESET0|
-		MAC_EN_RESET1|MAC_EN_RESET2;
-	udelay(10);
-
-	for(i=0;i<NO_OF_FIFOS;i++){
-		fifo_tx[i].len = 0;
-		fifo_tx[i].addr = virt_to_phys(&txbuf[0]);
-		fifo_rx[i].addr = (virt_to_phys(net_rx_packets[i])) |
-			RX_DMA_ENABLE;
-	}
-
-	/* Put mac addr in little endian */
-#define ea eth_get_ethaddr()
-	*mac_addr_high	=	(ea[5] <<  8) | (ea[4]	    ) ;
-	*mac_addr_low	=	(ea[3] << 24) | (ea[2] << 16) |
-		(ea[1] <<  8) | (ea[0]	    ) ;
-#undef ea
-	*mac_mcast_low = 0;
-	*mac_mcast_high = 0;
-
-	/* Make sure the MAC buffer is in the correct endian mode */
-#ifdef __LITTLE_ENDIAN
-	*mac_ctrl = MAC_FULL_DUPLEX;
-	udelay(1);
-	*mac_ctrl = MAC_FULL_DUPLEX|MAC_RX_ENABLE|MAC_TX_ENABLE;
-#else
-	*mac_ctrl = MAC_BIG_ENDIAN|MAC_FULL_DUPLEX;
-	udelay(1);
-	*mac_ctrl = MAC_BIG_ENDIAN|MAC_FULL_DUPLEX|MAC_RX_ENABLE|MAC_TX_ENABLE;
-#endif
-
-	return(1);
-}
-
-static void au1x00_halt(struct eth_device* dev){
-	volatile u32 *macen = (volatile u32*)MAC0_ENABLE;
-
-	/* Put MAC0 in reset */
-	*macen = 0;
-}
-
-int au1x00_enet_initialize(bd_t *bis){
-	struct eth_device* dev;
-
-	if ((dev = (struct eth_device*)malloc(sizeof *dev)) == NULL) {
-		puts ("malloc failed\n");
-		return -1;
-	}
-
-	memset(dev, 0, sizeof *dev);
-
-	strcpy(dev->name, "Au1X00 ethernet");
-	dev->iobase = 0;
-	dev->priv   = 0;
-	dev->init   = au1x00_init;
-	dev->halt   = au1x00_halt;
-	dev->send   = au1x00_send;
-	dev->recv   = au1x00_recv;
-
-	eth_register(dev);
-
-#if defined(CONFIG_CMD_MII)
-	int retval;
-	struct mii_dev *mdiodev = mdio_alloc();
-	if (!mdiodev)
-		return -ENOMEM;
-	strncpy(mdiodev->name, dev->name, MDIO_NAME_LEN);
-	mdiodev->read = au1x00_miiphy_read;
-	mdiodev->write = au1x00_miiphy_write;
-
-	retval = mdio_register(mdiodev);
-	if (retval < 0)
-		return retval;
-#endif
-
-	return 1;
-}
-
-int cpu_eth_init(bd_t *bis)
-{
-	au1x00_enet_initialize(bis);
-	return 0;
-}
diff --git a/arch/mips/mach-au1x00/au1x00_ide.c b/arch/mips/mach-au1x00/au1x00_ide.c
deleted file mode 100644
index ab52b99..0000000
--- a/arch/mips/mach-au1x00/au1x00_ide.c
+++ /dev/null
@@ -1,14 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2000-2011
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- */
-
-#include <common.h>
-#include <ide.h>
-
-/* AU1X00 swaps data in big-endian mode, enforce little-endian function */
-void ide_input_swap_data(int dev, ulong *sect_buf, int words)
-{
-	ide_input_data(dev, sect_buf, words);
-}
diff --git a/arch/mips/mach-au1x00/au1x00_serial.c b/arch/mips/mach-au1x00/au1x00_serial.c
deleted file mode 100644
index 4bcbc2d..0000000
--- a/arch/mips/mach-au1x00/au1x00_serial.c
+++ /dev/null
@@ -1,130 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * AU1X00 UART support
- *
- * Hardcoded to UART 0 for now
- * Speed and options also hardcoded to 115200 8N1
- *
- *  Copyright (c) 2003	Thomas.Lange@corelatus.se
- */
-
-#include <config.h>
-#include <common.h>
-#include <mach/au1x00.h>
-#include <serial.h>
-#include <linux/compiler.h>
-
-/******************************************************************************
-*
-* serial_init - initialize a channel
-*
-* This routine initializes the number of data bits, parity
-* and set the selected baud rate. Interrupts are disabled.
-* Set the modem control signals if the option is selected.
-*
-* RETURNS: N/A
-*/
-
-static int au1x00_serial_init(void)
-{
-	volatile u32 *uart_fifoctl = (volatile u32*)(UART0_ADDR+UART_FCR);
-	volatile u32 *uart_enable = (volatile u32*)(UART0_ADDR+UART_ENABLE);
-
-	/* Enable clocks first */
-	*uart_enable = UART_EN_CE;
-
-	/* Then release reset */
-	/* Must release reset before setting other regs */
-	*uart_enable = UART_EN_CE|UART_EN_E;
-
-	/* Activate fifos, reset tx and rx */
-	/* Set tx trigger level to 12 */
-	*uart_fifoctl = UART_FCR_ENABLE_FIFO|UART_FCR_CLEAR_RCVR|
-		UART_FCR_CLEAR_XMIT|UART_FCR_T_TRIGGER_12;
-
-	serial_setbrg();
-
-	return 0;
-}
-
-
-static void au1x00_serial_setbrg(void)
-{
-	volatile u32 *uart_clk = (volatile u32*)(UART0_ADDR+UART_CLK);
-	volatile u32 *uart_lcr = (volatile u32*)(UART0_ADDR+UART_LCR);
-	volatile u32 *sys_powerctrl = (u32 *)SYS_POWERCTRL;
-	int sd;
-	int divisorx2;
-
-	/* sd is system clock divisor			*/
-	/* see section 10.4.5 in au1550 datasheet	*/
-	sd = (*sys_powerctrl & 0x03) + 2;
-
-	/* calulate 2x baudrate and round */
-	divisorx2 = ((CONFIG_SYS_MIPS_TIMER_FREQ/(sd * 16 * CONFIG_BAUDRATE)));
-
-	if (divisorx2 & 0x01)
-		divisorx2 = divisorx2 + 1;
-
-	*uart_clk = divisorx2 / 2;
-
-	/* Set parity, stop bits and word length to 8N1 */
-	*uart_lcr = UART_LCR_WLEN8;
-}
-
-static void au1x00_serial_putc(const char c)
-{
-	volatile u32 *uart_lsr = (volatile u32*)(UART0_ADDR+UART_LSR);
-	volatile u32 *uart_tx = (volatile u32*)(UART0_ADDR+UART_TX);
-
-	if (c == '\n')
-		au1x00_serial_putc('\r');
-
-	/* Wait for fifo to shift out some bytes */
-	while((*uart_lsr&UART_LSR_THRE)==0);
-
-	*uart_tx = (u32)c;
-}
-
-static int au1x00_serial_getc(void)
-{
-	volatile u32 *uart_rx = (volatile u32*)(UART0_ADDR+UART_RX);
-	char c;
-
-	while (!serial_tstc());
-
-	c = (*uart_rx&0xFF);
-	return c;
-}
-
-static int au1x00_serial_tstc(void)
-{
-	volatile u32 *uart_lsr = (volatile u32*)(UART0_ADDR+UART_LSR);
-
-	if(*uart_lsr&UART_LSR_DR){
-		/* Data in rfifo */
-		return(1);
-	}
-	return 0;
-}
-
-static struct serial_device au1x00_serial_drv = {
-	.name	= "au1x00_serial",
-	.start	= au1x00_serial_init,
-	.stop	= NULL,
-	.setbrg	= au1x00_serial_setbrg,
-	.putc	= au1x00_serial_putc,
-	.puts	= default_serial_puts,
-	.getc	= au1x00_serial_getc,
-	.tstc	= au1x00_serial_tstc,
-};
-
-void au1x00_serial_initialize(void)
-{
-	serial_register(&au1x00_serial_drv);
-}
-
-__weak struct serial_device *default_serial_console(void)
-{
-	return &au1x00_serial_drv;
-}
diff --git a/arch/mips/mach-au1x00/au1x00_usb_ohci.c b/arch/mips/mach-au1x00/au1x00_usb_ohci.c
deleted file mode 100644
index 999b15a..0000000
--- a/arch/mips/mach-au1x00/au1x00_usb_ohci.c
+++ /dev/null
@@ -1,1609 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * URB OHCI HCD (Host Controller Driver) for USB on the AU1x00.
- *
- * (C) Copyright 2003
- * Gary Jennejohn, DENX Software Engineering <garyj@denx.de>
- * Note: Part of this code has been derived from linux
- *
- */
-/*
- * IMPORTANT NOTES
- * 1 - this driver is intended for use with USB Mass Storage Devices
- *     (BBB) ONLY. There is NO support for Interrupt or Isochronous pipes!
- */
-
-#include <config.h>
-
-#ifdef CONFIG_USB_OHCI
-
-/* #include <pci.h> no PCI on the AU1x00 */
-
-#include <common.h>
-#include <malloc.h>
-#include <asm/io.h>
-#include <mach/au1x00.h>
-#include <usb.h>
-#include "au1x00_usb_ohci.h"
-
-#define OHCI_USE_NPS		/* force NoPowerSwitching mode */
-#define OHCI_VERBOSE_DEBUG	/* not always helpful */
-#define OHCI_FILL_TRACE
-
-#define USBH_ENABLE_BE (1<<0)
-#define USBH_ENABLE_C  (1<<1)
-#define USBH_ENABLE_E  (1<<2)
-#define USBH_ENABLE_CE (1<<3)
-#define USBH_ENABLE_RD (1<<4)
-
-#ifdef __LITTLE_ENDIAN
-#define USBH_ENABLE_INIT (USBH_ENABLE_CE | USBH_ENABLE_E | USBH_ENABLE_C)
-#else
-#define USBH_ENABLE_INIT (USBH_ENABLE_CE | USBH_ENABLE_E | USBH_ENABLE_C | USBH_ENABLE_BE)
-#endif
-
-
-/* For initializing controller (mask in an HCFS mode too) */
-#define OHCI_CONTROL_INIT \
-	(OHCI_CTRL_CBSR & 0x3) | OHCI_CTRL_IE | OHCI_CTRL_PLE
-
-#undef readl
-#undef writel
-
-#define readl(a)     au_readl((long)(a))
-#define writel(v,a)  au_writel((v),(int)(a))
-
-#define DEBUG
-#ifdef DEBUG
-#define dbg(format, arg...) printf("DEBUG: " format "\n", ## arg)
-#else
-#define dbg(format, arg...) do {} while(0)
-#endif /* DEBUG */
-#define err(format, arg...) printf("ERROR: " format "\n", ## arg)
-#define SHOW_INFO
-#ifdef SHOW_INFO
-#define info(format, arg...) printf("INFO: " format "\n", ## arg)
-#else
-#define info(format, arg...) do {} while(0)
-#endif
-
-#define m16_swap(x) swap_16(x)
-#define m32_swap(x) swap_32(x)
-
-/* global ohci_t */
-static ohci_t gohci;
-/* this must be aligned to a 256 byte boundary */
-struct ohci_hcca ghcca[1];
-/* a pointer to the aligned storage */
-struct ohci_hcca *phcca;
-/* this allocates EDs for all possible endpoints */
-struct ohci_device ohci_dev;
-/* urb_priv */
-urb_priv_t urb_priv;
-/* RHSC flag */
-int got_rhsc;
-/* device which was disconnected */
-struct usb_device *devgone;
-
-/*-------------------------------------------------------------------------*/
-
-/* AMD-756 (D2 rev) reports corrupt register contents in some cases.
- * The erratum (#4) description is incorrect.  AMD's workaround waits
- * till some bits (mostly reserved) are clear; ok for all revs.
- */
-#define OHCI_QUIRK_AMD756 0xabcd
-#define read_roothub(hc, register, mask) ({ \
-	u32 temp = readl (&hc->regs->roothub.register); \
-	if (hc->flags & OHCI_QUIRK_AMD756) \
-		while (temp & mask) \
-			temp = readl (&hc->regs->roothub.register); \
-	temp; })
-
-static u32 roothub_a (struct ohci *hc)
-	{ return read_roothub (hc, a, 0xfc0fe000); }
-static inline u32 roothub_b (struct ohci *hc)
-	{ return readl (&hc->regs->roothub.b); }
-static inline u32 roothub_status (struct ohci *hc)
-	{ return readl (&hc->regs->roothub.status); }
-static u32 roothub_portstatus (struct ohci *hc, int i)
-	{ return read_roothub (hc, portstatus [i], 0xffe0fce0); }
-
-
-/* forward declaration */
-static int hc_interrupt (void);
-static void
-td_submit_job (struct usb_device * dev, unsigned long pipe, void * buffer,
-	int transfer_len, struct devrequest * setup, urb_priv_t * urb, int interval);
-
-/*-------------------------------------------------------------------------*
- * URB support functions
- *-------------------------------------------------------------------------*/
-
-/* free HCD-private data associated with this URB */
-
-static void urb_free_priv (urb_priv_t * urb)
-{
-	int		i;
-	int		last;
-	struct td	* td;
-
-	last = urb->length - 1;
-	if (last >= 0) {
-		for (i = 0; i <= last; i++) {
-			td = urb->td[i];
-			if (td) {
-				td->usb_dev = NULL;
-				urb->td[i] = NULL;
-			}
-		}
-	}
-}
-
-/*-------------------------------------------------------------------------*/
-
-#ifdef DEBUG
-static int sohci_get_current_frame_number (struct usb_device * dev);
-
-/* debug| print the main components of an URB
- * small: 0) header + data packets 1) just header */
-
-static void pkt_print (struct usb_device * dev, unsigned long pipe, void * buffer,
-	int transfer_len, struct devrequest * setup, char * str, int small)
-{
-	urb_priv_t * purb = &urb_priv;
-
-	dbg("%s URB:[%4x] dev:%2d,ep:%2d-%c,type:%s,len:%d/%d stat:%#lx",
-			str,
-			sohci_get_current_frame_number (dev),
-			usb_pipedevice (pipe),
-			usb_pipeendpoint (pipe),
-			usb_pipeout (pipe)? 'O': 'I',
-			usb_pipetype (pipe) < 2? (usb_pipeint (pipe)? "INTR": "ISOC"):
-				(usb_pipecontrol (pipe)? "CTRL": "BULK"),
-			purb->actual_length,
-			transfer_len, dev->status);
-#ifdef	OHCI_VERBOSE_DEBUG
-	if (!small) {
-		int i, len;
-
-		if (usb_pipecontrol (pipe)) {
-			printf (__FILE__ ": cmd(8):");
-			for (i = 0; i < 8 ; i++)
-				printf (" %02x", ((__u8 *) setup) [i]);
-			printf ("\n");
-		}
-		if (transfer_len > 0 && buffer) {
-			printf (__FILE__ ": data(%d/%d):",
-				purb->actual_length,
-				transfer_len);
-			len = usb_pipeout (pipe)?
-					transfer_len: purb->actual_length;
-			for (i = 0; i < 16 && i < len; i++)
-				printf (" %02x", ((__u8 *) buffer) [i]);
-			printf ("%s\n", i < len? "...": "");
-		}
-	}
-#endif
-}
-
-/* just for debugging; prints non-empty branches of the int ed tree inclusive iso eds*/
-void ep_print_int_eds (ohci_t *ohci, char * str) {
-	int i, j;
-	 __u32 * ed_p;
-	for (i= 0; i < 32; i++) {
-		j = 5;
-		ed_p = &(ohci->hcca->int_table [i]);
-		if (*ed_p == 0)
-		    continue;
-		printf (__FILE__ ": %s branch int %2d(%2x):", str, i, i);
-		while (*ed_p != 0 && j--) {
-			ed_t *ed = (ed_t *)m32_swap(ed_p);
-			printf (" ed: %4x;", ed->hwINFO);
-			ed_p = &ed->hwNextED;
-		}
-		printf ("\n");
-	}
-}
-
-static void ohci_dump_intr_mask (char *label, __u32 mask)
-{
-	dbg ("%s: 0x%08x%s%s%s%s%s%s%s%s%s",
-		label,
-		mask,
-		(mask & OHCI_INTR_MIE) ? " MIE" : "",
-		(mask & OHCI_INTR_OC) ? " OC" : "",
-		(mask & OHCI_INTR_RHSC) ? " RHSC" : "",
-		(mask & OHCI_INTR_FNO) ? " FNO" : "",
-		(mask & OHCI_INTR_UE) ? " UE" : "",
-		(mask & OHCI_INTR_RD) ? " RD" : "",
-		(mask & OHCI_INTR_SF) ? " SF" : "",
-		(mask & OHCI_INTR_WDH) ? " WDH" : "",
-		(mask & OHCI_INTR_SO) ? " SO" : ""
-		);
-}
-
-static void maybe_print_eds (char *label, __u32 value)
-{
-	ed_t *edp = (ed_t *)value;
-
-	if (value) {
-		dbg ("%s %08x", label, value);
-		dbg ("%08x", edp->hwINFO);
-		dbg ("%08x", edp->hwTailP);
-		dbg ("%08x", edp->hwHeadP);
-		dbg ("%08x", edp->hwNextED);
-	}
-}
-
-static char * hcfs2string (int state)
-{
-	switch (state) {
-		case OHCI_USB_RESET:	return "reset";
-		case OHCI_USB_RESUME:	return "resume";
-		case OHCI_USB_OPER:	return "operational";
-		case OHCI_USB_SUSPEND:	return "suspend";
-	}
-	return "?";
-}
-
-/* dump control and status registers */
-static void ohci_dump_status (ohci_t *controller)
-{
-	struct ohci_regs	*regs = controller->regs;
-	__u32			temp;
-
-	temp = readl (&regs->revision) & 0xff;
-	if (temp != 0x10)
-		dbg ("spec %d.%d", (temp >> 4), (temp & 0x0f));
-
-	temp = readl (&regs->control);
-	dbg ("control: 0x%08x%s%s%s HCFS=%s%s%s%s%s CBSR=%d", temp,
-		(temp & OHCI_CTRL_RWE) ? " RWE" : "",
-		(temp & OHCI_CTRL_RWC) ? " RWC" : "",
-		(temp & OHCI_CTRL_IR) ? " IR" : "",
-		hcfs2string (temp & OHCI_CTRL_HCFS),
-		(temp & OHCI_CTRL_BLE) ? " BLE" : "",
-		(temp & OHCI_CTRL_CLE) ? " CLE" : "",
-		(temp & OHCI_CTRL_IE) ? " IE" : "",
-		(temp & OHCI_CTRL_PLE) ? " PLE" : "",
-		temp & OHCI_CTRL_CBSR
-		);
-
-	temp = readl (&regs->cmdstatus);
-	dbg ("cmdstatus: 0x%08x SOC=%d%s%s%s%s", temp,
-		(temp & OHCI_SOC) >> 16,
-		(temp & OHCI_OCR) ? " OCR" : "",
-		(temp & OHCI_BLF) ? " BLF" : "",
-		(temp & OHCI_CLF) ? " CLF" : "",
-		(temp & OHCI_HCR) ? " HCR" : ""
-		);
-
-	ohci_dump_intr_mask ("intrstatus", readl (&regs->intrstatus));
-	ohci_dump_intr_mask ("intrenable", readl (&regs->intrenable));
-
-	maybe_print_eds ("ed_periodcurrent", readl (&regs->ed_periodcurrent));
-
-	maybe_print_eds ("ed_controlhead", readl (&regs->ed_controlhead));
-	maybe_print_eds ("ed_controlcurrent", readl (&regs->ed_controlcurrent));
-
-	maybe_print_eds ("ed_bulkhead", readl (&regs->ed_bulkhead));
-	maybe_print_eds ("ed_bulkcurrent", readl (&regs->ed_bulkcurrent));
-
-	maybe_print_eds ("donehead", readl (&regs->donehead));
-}
-
-static void ohci_dump_roothub (ohci_t *controller, int verbose)
-{
-	__u32			temp, ndp, i;
-
-	temp = roothub_a (controller);
-	ndp = (temp & RH_A_NDP);
-
-	if (verbose) {
-		dbg ("roothub.a: %08x POTPGT=%d%s%s%s%s%s NDP=%d", temp,
-			((temp & RH_A_POTPGT) >> 24) & 0xff,
-			(temp & RH_A_NOCP) ? " NOCP" : "",
-			(temp & RH_A_OCPM) ? " OCPM" : "",
-			(temp & RH_A_DT) ? " DT" : "",
-			(temp & RH_A_NPS) ? " NPS" : "",
-			(temp & RH_A_PSM) ? " PSM" : "",
-			ndp
-			);
-		temp = roothub_b (controller);
-		dbg ("roothub.b: %08x PPCM=%04x DR=%04x",
-			temp,
-			(temp & RH_B_PPCM) >> 16,
-			(temp & RH_B_DR)
-			);
-		temp = roothub_status (controller);
-		dbg ("roothub.status: %08x%s%s%s%s%s%s",
-			temp,
-			(temp & RH_HS_CRWE) ? " CRWE" : "",
-			(temp & RH_HS_OCIC) ? " OCIC" : "",
-			(temp & RH_HS_LPSC) ? " LPSC" : "",
-			(temp & RH_HS_DRWE) ? " DRWE" : "",
-			(temp & RH_HS_OCI) ? " OCI" : "",
-			(temp & RH_HS_LPS) ? " LPS" : ""
-			);
-	}
-
-	for (i = 0; i < ndp; i++) {
-		temp = roothub_portstatus (controller, i);
-		dbg ("roothub.portstatus [%d] = 0x%08x%s%s%s%s%s%s%s%s%s%s%s%s",
-			i,
-			temp,
-			(temp & RH_PS_PRSC) ? " PRSC" : "",
-			(temp & RH_PS_OCIC) ? " OCIC" : "",
-			(temp & RH_PS_PSSC) ? " PSSC" : "",
-			(temp & RH_PS_PESC) ? " PESC" : "",
-			(temp & RH_PS_CSC) ? " CSC" : "",
-
-			(temp & RH_PS_LSDA) ? " LSDA" : "",
-			(temp & RH_PS_PPS) ? " PPS" : "",
-			(temp & RH_PS_PRS) ? " PRS" : "",
-			(temp & RH_PS_POCI) ? " POCI" : "",
-			(temp & RH_PS_PSS) ? " PSS" : "",
-
-			(temp & RH_PS_PES) ? " PES" : "",
-			(temp & RH_PS_CCS) ? " CCS" : ""
-			);
-	}
-}
-
-static void ohci_dump (ohci_t *controller, int verbose)
-{
-	dbg ("OHCI controller usb-%s state", controller->slot_name);
-
-	/* dumps some of the state we know about */
-	ohci_dump_status (controller);
-	if (verbose)
-		ep_print_int_eds (controller, "hcca");
-	dbg ("hcca frame #%04x", controller->hcca->frame_no);
-	ohci_dump_roothub (controller, 1);
-}
-
-
-#endif /* DEBUG */
-
-/*-------------------------------------------------------------------------*
- * Interface functions (URB)
- *-------------------------------------------------------------------------*/
-
-/* get a transfer request */
-
-int sohci_submit_job(struct usb_device *dev, unsigned long pipe, void *buffer,
-		int transfer_len, struct devrequest *setup, int interval)
-{
-	ohci_t *ohci;
-	ed_t * ed;
-	urb_priv_t *purb_priv;
-	int i, size = 0;
-
-	ohci = &gohci;
-
-	/* when controller's hung, permit only roothub cleanup attempts
-	 * such as powering down ports */
-	if (ohci->disabled) {
-		err("sohci_submit_job: EPIPE");
-		return -1;
-	}
-
-	/* every endpoint has a ed, locate and fill it */
-	if (!(ed = ep_add_ed (dev, pipe))) {
-		err("sohci_submit_job: ENOMEM");
-		return -1;
-	}
-
-	/* for the private part of the URB we need the number of TDs (size) */
-	switch (usb_pipetype (pipe)) {
-		case PIPE_BULK: /* one TD for every 4096 Byte */
-			size = (transfer_len - 1) / 4096 + 1;
-			break;
-		case PIPE_CONTROL: /* 1 TD for setup, 1 for ACK and 1 for every 4096 B */
-			size = (transfer_len == 0)? 2:
-						(transfer_len - 1) / 4096 + 3;
-			break;
-	}
-
-	if (size >= (N_URB_TD - 1)) {
-		err("need %d TDs, only have %d", size, N_URB_TD);
-		return -1;
-	}
-	purb_priv = &urb_priv;
-	purb_priv->pipe = pipe;
-
-	/* fill the private part of the URB */
-	purb_priv->length = size;
-	purb_priv->ed = ed;
-	purb_priv->actual_length = 0;
-
-	/* allocate the TDs */
-	/* note that td[0] was allocated in ep_add_ed */
-	for (i = 0; i < size; i++) {
-		purb_priv->td[i] = td_alloc (dev);
-		if (!purb_priv->td[i]) {
-			purb_priv->length = i;
-			urb_free_priv (purb_priv);
-			err("sohci_submit_job: ENOMEM");
-			return -1;
-		}
-	}
-
-	if (ed->state == ED_NEW || (ed->state & ED_DEL)) {
-		urb_free_priv (purb_priv);
-		err("sohci_submit_job: EINVAL");
-		return -1;
-	}
-
-	/* link the ed into a chain if is not already */
-	if (ed->state != ED_OPER)
-		ep_link (ohci, ed);
-
-	/* fill the TDs and link it to the ed */
-	td_submit_job(dev, pipe, buffer, transfer_len, setup, purb_priv, interval);
-
-	return 0;
-}
-
-/*-------------------------------------------------------------------------*/
-
-#ifdef DEBUG
-/* tell us the current USB frame number */
-
-static int sohci_get_current_frame_number (struct usb_device *usb_dev)
-{
-	ohci_t *ohci = &gohci;
-
-	return m16_swap (ohci->hcca->frame_no);
-}
-#endif
-
-/*-------------------------------------------------------------------------*
- * ED handling functions
- *-------------------------------------------------------------------------*/
-
-/* link an ed into one of the HC chains */
-
-static int ep_link (ohci_t *ohci, ed_t *edi)
-{
-	volatile ed_t *ed = edi;
-
-	ed->state = ED_OPER;
-
-	switch (ed->type) {
-	case PIPE_CONTROL:
-		ed->hwNextED = 0;
-		if (ohci->ed_controltail == NULL) {
-			writel ((long)ed, &ohci->regs->ed_controlhead);
-		} else {
-			ohci->ed_controltail->hwNextED = m32_swap (ed);
-		}
-		ed->ed_prev = ohci->ed_controltail;
-		if (!ohci->ed_controltail && !ohci->ed_rm_list[0] &&
-			!ohci->ed_rm_list[1] && !ohci->sleeping) {
-			ohci->hc_control |= OHCI_CTRL_CLE;
-			writel (ohci->hc_control, &ohci->regs->control);
-		}
-		ohci->ed_controltail = edi;
-		break;
-
-	case PIPE_BULK:
-		ed->hwNextED = 0;
-		if (ohci->ed_bulktail == NULL) {
-			writel ((long)ed, &ohci->regs->ed_bulkhead);
-		} else {
-			ohci->ed_bulktail->hwNextED = m32_swap (ed);
-		}
-		ed->ed_prev = ohci->ed_bulktail;
-		if (!ohci->ed_bulktail && !ohci->ed_rm_list[0] &&
-			!ohci->ed_rm_list[1] && !ohci->sleeping) {
-			ohci->hc_control |= OHCI_CTRL_BLE;
-			writel (ohci->hc_control, &ohci->regs->control);
-		}
-		ohci->ed_bulktail = edi;
-		break;
-	}
-	return 0;
-}
-
-/*-------------------------------------------------------------------------*/
-
-/* unlink an ed from one of the HC chains.
- * just the link to the ed is unlinked.
- * the link from the ed still points to another operational ed or 0
- * so the HC can eventually finish the processing of the unlinked ed */
-
-static int ep_unlink (ohci_t *ohci, ed_t *ed)
-{
-	ed->hwINFO |= m32_swap (OHCI_ED_SKIP);
-
-	switch (ed->type) {
-	case PIPE_CONTROL:
-		if (ed->ed_prev == NULL) {
-			if (!ed->hwNextED) {
-				ohci->hc_control &= ~OHCI_CTRL_CLE;
-				writel (ohci->hc_control, &ohci->regs->control);
-			}
-			writel (m32_swap (*((__u32 *)&ed->hwNextED)), &ohci->regs->ed_controlhead);
-		} else {
-			ed->ed_prev->hwNextED = ed->hwNextED;
-		}
-		if (ohci->ed_controltail == ed) {
-			ohci->ed_controltail = ed->ed_prev;
-		} else {
-			((ed_t *)m32_swap (*((__u32 *)&ed->hwNextED)))->ed_prev = ed->ed_prev;
-		}
-		break;
-
-	case PIPE_BULK:
-		if (ed->ed_prev == NULL) {
-			if (!ed->hwNextED) {
-				ohci->hc_control &= ~OHCI_CTRL_BLE;
-				writel (ohci->hc_control, &ohci->regs->control);
-			}
-			writel (m32_swap (*((__u32 *)&ed->hwNextED)), &ohci->regs->ed_bulkhead);
-		} else {
-			ed->ed_prev->hwNextED = ed->hwNextED;
-		}
-		if (ohci->ed_bulktail == ed) {
-			ohci->ed_bulktail = ed->ed_prev;
-		} else {
-			((ed_t *)m32_swap (*((__u32 *)&ed->hwNextED)))->ed_prev = ed->ed_prev;
-		}
-		break;
-	}
-	ed->state = ED_UNLINK;
-	return 0;
-}
-
-
-/*-------------------------------------------------------------------------*/
-
-/* add/reinit an endpoint; this should be done once at the usb_set_configuration command,
- * but the USB stack is a little bit stateless	so we do it at every transaction
- * if the state of the ed is ED_NEW then a dummy td is added and the state is changed to ED_UNLINK
- * in all other cases the state is left unchanged
- * the ed info fields are setted anyway even though most of them should not change */
-
-static ed_t * ep_add_ed (struct usb_device *usb_dev, unsigned long pipe)
-{
-	td_t *td;
-	ed_t *ed_ret;
-	volatile ed_t *ed;
-
-	ed = ed_ret = &ohci_dev.ed[(usb_pipeendpoint (pipe) << 1) |
-			(usb_pipecontrol (pipe)? 0: usb_pipeout (pipe))];
-
-	if ((ed->state & ED_DEL) || (ed->state & ED_URB_DEL)) {
-		err("ep_add_ed: pending delete");
-		/* pending delete request */
-		return NULL;
-	}
-
-	if (ed->state == ED_NEW) {
-		ed->hwINFO = m32_swap (OHCI_ED_SKIP); /* skip ed */
-		/* dummy td; end of td list for ed */
-		td = td_alloc (usb_dev);
-		ed->hwTailP = m32_swap (td);
-		ed->hwHeadP = ed->hwTailP;
-		ed->state = ED_UNLINK;
-		ed->type = usb_pipetype (pipe);
-		ohci_dev.ed_cnt++;
-	}
-
-	ed->hwINFO = m32_swap (usb_pipedevice (pipe)
-			| usb_pipeendpoint (pipe) << 7
-			| (usb_pipeisoc (pipe)? 0x8000: 0)
-			| (usb_pipecontrol (pipe)? 0: (usb_pipeout (pipe)? 0x800: 0x1000))
-			| (usb_dev->speed == USB_SPEED_LOW) << 13
-			| usb_maxpacket (usb_dev, pipe) << 16);
-
-	return ed_ret;
-}
-
-/*-------------------------------------------------------------------------*
- * TD handling functions
- *-------------------------------------------------------------------------*/
-
-/* enqueue next TD for this URB (OHCI spec 5.2.8.2) */
-
-static void td_fill (ohci_t *ohci, unsigned int info,
-	void *data, int len,
-	struct usb_device *dev, int index, urb_priv_t *urb_priv)
-{
-	volatile td_t  *td, *td_pt;
-#ifdef OHCI_FILL_TRACE
-	int i;
-#endif
-
-	if (index > urb_priv->length) {
-		err("index > length");
-		return;
-	}
-	/* use this td as the next dummy */
-	td_pt = urb_priv->td [index];
-	td_pt->hwNextTD = 0;
-
-	/* fill the old dummy TD */
-	td = urb_priv->td [index] = (td_t *)(m32_swap (urb_priv->ed->hwTailP) & ~0xf);
-
-	td->ed = urb_priv->ed;
-	td->next_dl_td = NULL;
-	td->index = index;
-	td->data = (__u32)data;
-#ifdef OHCI_FILL_TRACE
-	if (1 || (usb_pipebulk(urb_priv->pipe) &&
-				usb_pipeout(urb_priv->pipe))) {
-		for (i = 0; i < len; i++)
-		printf("td->data[%d] %#2x\n",i, ((unsigned char *)(td->data+0x80000000))[i]);
-	}
-#endif
-	if (!len)
-		data = 0;
-
-	td->hwINFO = m32_swap (info);
-	td->hwCBP = m32_swap (data);
-	if (data)
-		td->hwBE = m32_swap (data + len - 1);
-	else
-		td->hwBE = 0;
-	td->hwNextTD = m32_swap (td_pt);
-	td->hwPSW [0] = m16_swap (((__u32)data & 0x0FFF) | 0xE000);
-
-	/* append to queue */
-	td->ed->hwTailP = td->hwNextTD;
-}
-
-/*-------------------------------------------------------------------------*/
-
-/* prepare all TDs of a transfer */
-
-#define kseg_to_phys(x)	  ((void *)((__u32)(x) - 0x80000000))
-
-static void td_submit_job (struct usb_device *dev, unsigned long pipe, void *buffer,
-	int transfer_len, struct devrequest *setup, urb_priv_t *urb, int interval)
-{
-	ohci_t *ohci = &gohci;
-	int data_len = transfer_len;
-	void *data;
-	int cnt = 0;
-	__u32 info = 0;
-	unsigned int toggle = 0;
-
-	/* OHCI handles the DATA-toggles itself, we just use the
-	   USB-toggle bits for resetting */
-	if(usb_gettoggle(dev, usb_pipeendpoint(pipe), usb_pipeout(pipe))) {
-		toggle = TD_T_TOGGLE;
-	} else {
-		toggle = TD_T_DATA0;
-		usb_settoggle(dev, usb_pipeendpoint(pipe), usb_pipeout(pipe), 1);
-	}
-	urb->td_cnt = 0;
-	if (data_len)
-		data = kseg_to_phys(buffer);
-	else
-		data = 0;
-
-	switch (usb_pipetype (pipe)) {
-	case PIPE_BULK:
-		info = usb_pipeout (pipe)?
-			TD_CC | TD_DP_OUT : TD_CC | TD_DP_IN ;
-		while(data_len > 4096) {
-			td_fill (ohci, info | (cnt? TD_T_TOGGLE:toggle), data, 4096, dev, cnt, urb);
-			data += 4096; data_len -= 4096; cnt++;
-		}
-		info = usb_pipeout (pipe)?
-			TD_CC | TD_DP_OUT : TD_CC | TD_R | TD_DP_IN ;
-		td_fill (ohci, info | (cnt? TD_T_TOGGLE:toggle), data, data_len, dev, cnt, urb);
-		cnt++;
-
-		if (!ohci->sleeping)
-			writel (OHCI_BLF, &ohci->regs->cmdstatus); /* start bulk list */
-		break;
-
-	case PIPE_CONTROL:
-		info = TD_CC | TD_DP_SETUP | TD_T_DATA0;
-		td_fill (ohci, info, kseg_to_phys(setup), 8, dev, cnt++, urb);
-		if (data_len > 0) {
-			info = usb_pipeout (pipe)?
-				TD_CC | TD_R | TD_DP_OUT | TD_T_DATA1 : TD_CC | TD_R | TD_DP_IN | TD_T_DATA1;
-			/* NOTE:  mishandles transfers >8K, some >4K */
-			td_fill (ohci, info, data, data_len, dev, cnt++, urb);
-		}
-		info = usb_pipeout (pipe)?
-			TD_CC | TD_DP_IN | TD_T_DATA1: TD_CC | TD_DP_OUT | TD_T_DATA1;
-		td_fill (ohci, info, data, 0, dev, cnt++, urb);
-		if (!ohci->sleeping)
-			writel (OHCI_CLF, &ohci->regs->cmdstatus); /* start Control list */
-		break;
-	}
-	if (urb->length != cnt)
-		dbg("TD LENGTH %d != CNT %d", urb->length, cnt);
-}
-
-/*-------------------------------------------------------------------------*
- * Done List handling functions
- *-------------------------------------------------------------------------*/
-
-
-/* calculate the transfer length and update the urb */
-
-static void dl_transfer_length(td_t * td)
-{
-	__u32 tdINFO, tdBE, tdCBP;
-	urb_priv_t *lurb_priv = &urb_priv;
-
-	tdINFO = m32_swap (td->hwINFO);
-	tdBE   = m32_swap (td->hwBE);
-	tdCBP  = m32_swap (td->hwCBP);
-
-
-	if (!(usb_pipecontrol(lurb_priv->pipe) &&
-	    ((td->index == 0) || (td->index == lurb_priv->length - 1)))) {
-		if (tdBE != 0) {
-			if (td->hwCBP == 0)
-				lurb_priv->actual_length += tdBE - td->data + 1;
-			else
-				lurb_priv->actual_length += tdCBP - td->data;
-		}
-	}
-}
-
-/*-------------------------------------------------------------------------*/
-
-/* replies to the request have to be on a FIFO basis so
- * we reverse the reversed done-list */
-
-static td_t * dl_reverse_done_list (ohci_t *ohci)
-{
-	__u32 td_list_hc;
-	td_t *td_rev = NULL;
-	td_t *td_list = NULL;
-	urb_priv_t *lurb_priv = NULL;
-
-	td_list_hc = m32_swap (ohci->hcca->done_head) & 0xfffffff0;
-	ohci->hcca->done_head = 0;
-
-	while (td_list_hc) {
-		td_list = (td_t *)td_list_hc;
-
-		if (TD_CC_GET (m32_swap (td_list->hwINFO))) {
-			lurb_priv = &urb_priv;
-			dbg(" USB-error/status: %x : %p",
-					TD_CC_GET (m32_swap (td_list->hwINFO)), td_list);
-			if (td_list->ed->hwHeadP & m32_swap (0x1)) {
-				if (lurb_priv && ((td_list->index + 1) < lurb_priv->length)) {
-					td_list->ed->hwHeadP =
-						(lurb_priv->td[lurb_priv->length - 1]->hwNextTD & m32_swap (0xfffffff0)) |
-									(td_list->ed->hwHeadP & m32_swap (0x2));
-					lurb_priv->td_cnt += lurb_priv->length - td_list->index - 1;
-				} else
-					td_list->ed->hwHeadP &= m32_swap (0xfffffff2);
-			}
-		}
-
-		td_list->next_dl_td = td_rev;
-		td_rev = td_list;
-		td_list_hc = m32_swap (td_list->hwNextTD) & 0xfffffff0;
-	}
-	return td_list;
-}
-
-/*-------------------------------------------------------------------------*/
-
-/* td done list */
-static int dl_done_list (ohci_t *ohci, td_t *td_list)
-{
-	td_t *td_list_next = NULL;
-	ed_t *ed;
-	int cc = 0;
-	int stat = 0;
-	/* urb_t *urb; */
-	urb_priv_t *lurb_priv;
-	__u32 tdINFO, edHeadP, edTailP;
-
-	while (td_list) {
-		td_list_next = td_list->next_dl_td;
-
-		lurb_priv = &urb_priv;
-		tdINFO = m32_swap (td_list->hwINFO);
-
-		ed = td_list->ed;
-
-		dl_transfer_length(td_list);
-
-		/* error code of transfer */
-		cc = TD_CC_GET (tdINFO);
-		if (cc != 0) {
-			dbg("ConditionCode %#x", cc);
-			stat = cc_to_error[cc];
-		}
-
-		if (ed->state != ED_NEW) {
-			edHeadP = m32_swap (ed->hwHeadP) & 0xfffffff0;
-			edTailP = m32_swap (ed->hwTailP);
-
-			/* unlink eds if they are not busy */
-			if ((edHeadP == edTailP) && (ed->state == ED_OPER))
-				ep_unlink (ohci, ed);
-		}
-
-		td_list = td_list_next;
-	}
-	return stat;
-}
-
-/*-------------------------------------------------------------------------*
- * Virtual Root Hub
- *-------------------------------------------------------------------------*/
-
-#include <usbroothubdes.h>
-
-/* Hub class-specific descriptor is constructed dynamically */
-
-
-/*-------------------------------------------------------------------------*/
-
-#define OK(x)			len = (x); break
-#ifdef DEBUG
-#define WR_RH_STAT(x)		{info("WR:status %#8x", (x));writel((x), &gohci.regs->roothub.status);}
-#define WR_RH_PORTSTAT(x)	{info("WR:portstatus[%d] %#8x", wIndex-1, (x));writel((x), &gohci.regs->roothub.portstatus[wIndex-1]);}
-#else
-#define WR_RH_STAT(x)		writel((x), &gohci.regs->roothub.status)
-#define WR_RH_PORTSTAT(x)	writel((x), &gohci.regs->roothub.portstatus[wIndex-1])
-#endif
-#define RD_RH_STAT		roothub_status(&gohci)
-#define RD_RH_PORTSTAT		roothub_portstatus(&gohci,wIndex-1)
-
-/* request to virtual root hub */
-
-int rh_check_port_status(ohci_t *controller)
-{
-	__u32 temp, ndp, i;
-	int res;
-
-	res = -1;
-	temp = roothub_a (controller);
-	ndp = (temp & RH_A_NDP);
-	for (i = 0; i < ndp; i++) {
-		temp = roothub_portstatus (controller, i);
-		/* check for a device disconnect */
-		if (((temp & (RH_PS_PESC | RH_PS_CSC)) ==
-			(RH_PS_PESC | RH_PS_CSC)) &&
-			((temp & RH_PS_CCS) == 0)) {
-			res = i;
-			break;
-		}
-	}
-	return res;
-}
-
-static int ohci_submit_rh_msg(struct usb_device *dev, unsigned long pipe,
-		void *buffer, int transfer_len, struct devrequest *cmd)
-{
-	void * data = buffer;
-	int leni = transfer_len;
-	int len = 0;
-	int stat = 0;
-	__u32 datab[4];
-	__u8 *data_buf = (__u8 *)datab;
-	__u16 bmRType_bReq;
-	__u16 wValue;
-	__u16 wIndex;
-	__u16 wLength;
-
-#ifdef DEBUG
-urb_priv.actual_length = 0;
-pkt_print(dev, pipe, buffer, transfer_len, cmd, "SUB(rh)", usb_pipein(pipe));
-#else
-	mdelay(1);
-#endif
-	if (usb_pipeint(pipe)) {
-		info("Root-Hub submit IRQ: NOT implemented");
-		return 0;
-	}
-
-	bmRType_bReq  = cmd->requesttype | (cmd->request << 8);
-	wValue	      = m16_swap (cmd->value);
-	wIndex	      = m16_swap (cmd->index);
-	wLength	      = m16_swap (cmd->length);
-
-	info("Root-Hub: adr: %2x cmd(%1x): %08x %04x %04x %04x",
-		dev->devnum, 8, bmRType_bReq, wValue, wIndex, wLength);
-
-	switch (bmRType_bReq) {
-	/* Request Destination:
-	   without flags: Device,
-	   RH_INTERFACE: interface,
-	   RH_ENDPOINT: endpoint,
-	   RH_CLASS means HUB here,
-	   RH_OTHER | RH_CLASS	almost ever means HUB_PORT here
-	*/
-
-	case RH_GET_STATUS:
-			*(__u16 *) data_buf = m16_swap (1); OK (2);
-	case RH_GET_STATUS | RH_INTERFACE:
-			*(__u16 *) data_buf = m16_swap (0); OK (2);
-	case RH_GET_STATUS | RH_ENDPOINT:
-			*(__u16 *) data_buf = m16_swap (0); OK (2);
-	case RH_GET_STATUS | RH_CLASS:
-			*(__u32 *) data_buf = m32_swap (
-				RD_RH_STAT & ~(RH_HS_CRWE | RH_HS_DRWE));
-			OK (4);
-	case RH_GET_STATUS | RH_OTHER | RH_CLASS:
-			*(__u32 *) data_buf = m32_swap (RD_RH_PORTSTAT); OK (4);
-
-	case RH_CLEAR_FEATURE | RH_ENDPOINT:
-		switch (wValue) {
-			case (RH_ENDPOINT_STALL): OK (0);
-		}
-		break;
-
-	case RH_CLEAR_FEATURE | RH_CLASS:
-		switch (wValue) {
-			case RH_C_HUB_LOCAL_POWER:
-				OK(0);
-			case (RH_C_HUB_OVER_CURRENT):
-					WR_RH_STAT(RH_HS_OCIC); OK (0);
-		}
-		break;
-
-	case RH_CLEAR_FEATURE | RH_OTHER | RH_CLASS:
-		switch (wValue) {
-			case (RH_PORT_ENABLE):
-					WR_RH_PORTSTAT (RH_PS_CCS ); OK (0);
-			case (RH_PORT_SUSPEND):
-					WR_RH_PORTSTAT (RH_PS_POCI); OK (0);
-			case (RH_PORT_POWER):
-					WR_RH_PORTSTAT (RH_PS_LSDA); OK (0);
-			case (RH_C_PORT_CONNECTION):
-					WR_RH_PORTSTAT (RH_PS_CSC ); OK (0);
-			case (RH_C_PORT_ENABLE):
-					WR_RH_PORTSTAT (RH_PS_PESC); OK (0);
-			case (RH_C_PORT_SUSPEND):
-					WR_RH_PORTSTAT (RH_PS_PSSC); OK (0);
-			case (RH_C_PORT_OVER_CURRENT):
-					WR_RH_PORTSTAT (RH_PS_OCIC); OK (0);
-			case (RH_C_PORT_RESET):
-					WR_RH_PORTSTAT (RH_PS_PRSC); OK (0);
-		}
-		break;
-
-	case RH_SET_FEATURE | RH_OTHER | RH_CLASS:
-		switch (wValue) {
-			case (RH_PORT_SUSPEND):
-					WR_RH_PORTSTAT (RH_PS_PSS ); OK (0);
-			case (RH_PORT_RESET): /* BUG IN HUP CODE *********/
-					if (RD_RH_PORTSTAT & RH_PS_CCS)
-					    WR_RH_PORTSTAT (RH_PS_PRS);
-					OK (0);
-			case (RH_PORT_POWER):
-					WR_RH_PORTSTAT (RH_PS_PPS ); OK (0);
-			case (RH_PORT_ENABLE): /* BUG IN HUP CODE *********/
-					if (RD_RH_PORTSTAT & RH_PS_CCS)
-					    WR_RH_PORTSTAT (RH_PS_PES );
-					OK (0);
-		}
-		break;
-
-	case RH_SET_ADDRESS: gohci.rh.devnum = wValue; OK(0);
-
-	case RH_GET_DESCRIPTOR:
-		switch ((wValue & 0xff00) >> 8) {
-			case (0x01): /* device descriptor */
-				len = min_t(unsigned int,
-					  leni,
-					  min_t(unsigned int,
-					      sizeof (root_hub_dev_des),
-					      wLength));
-				data_buf = root_hub_dev_des; OK(len);
-			case (0x02): /* configuration descriptor */
-				len = min_t(unsigned int,
-					  leni,
-					  min_t(unsigned int,
-					      sizeof (root_hub_config_des),
-					      wLength));
-				data_buf = root_hub_config_des; OK(len);
-			case (0x03): /* string descriptors */
-				if(wValue==0x0300) {
-					len = min_t(unsigned int,
-						  leni,
-						  min_t(unsigned int,
-						      sizeof (root_hub_str_index0),
-						      wLength));
-					data_buf = root_hub_str_index0;
-					OK(len);
-				}
-				if(wValue==0x0301) {
-					len = min_t(unsigned int,
-						  leni,
-						  min_t(unsigned int,
-						      sizeof (root_hub_str_index1),
-						      wLength));
-					data_buf = root_hub_str_index1;
-					OK(len);
-			}
-			default:
-				stat = USB_ST_STALLED;
-		}
-		break;
-
-	case RH_GET_DESCRIPTOR | RH_CLASS:
-	    {
-		    __u32 temp = roothub_a (&gohci);
-
-		    data_buf [0] = 9;		/* min length; */
-		    data_buf [1] = 0x29;
-		    data_buf [2] = temp & RH_A_NDP;
-		    data_buf [3] = 0;
-		    if (temp & RH_A_PSM)	/* per-port power switching? */
-			data_buf [3] |= 0x1;
-		    if (temp & RH_A_NOCP)	/* no overcurrent reporting? */
-			data_buf [3] |= 0x10;
-		    else if (temp & RH_A_OCPM)	/* per-port overcurrent reporting? */
-			data_buf [3] |= 0x8;
-
-		    /* corresponds to data_buf[4-7] */
-		    datab [1] = 0;
-		    data_buf [5] = (temp & RH_A_POTPGT) >> 24;
-		    temp = roothub_b (&gohci);
-		    data_buf [7] = temp & RH_B_DR;
-		    if (data_buf [2] < 7) {
-			data_buf [8] = 0xff;
-		    } else {
-			data_buf [0] += 2;
-			data_buf [8] = (temp & RH_B_DR) >> 8;
-			data_buf [10] = data_buf [9] = 0xff;
-		    }
-
-		    len = min_t(unsigned int, leni,
-			      min_t(unsigned int, data_buf [0], wLength));
-		    OK (len);
-		}
-
-	case RH_GET_CONFIGURATION:	*(__u8 *) data_buf = 0x01; OK (1);
-
-	case RH_SET_CONFIGURATION:	WR_RH_STAT (0x10000); OK (0);
-
-	default:
-		dbg ("unsupported root hub command");
-		stat = USB_ST_STALLED;
-	}
-
-#ifdef	DEBUG
-	ohci_dump_roothub (&gohci, 1);
-#else
-	mdelay(1);
-#endif
-
-	len = min_t(int, len, leni);
-	if (data != data_buf)
-	    memcpy (data, data_buf, len);
-	dev->act_len = len;
-	dev->status = stat;
-
-#ifdef DEBUG
-	if (transfer_len)
-		urb_priv.actual_length = transfer_len;
-	pkt_print(dev, pipe, buffer, transfer_len, cmd, "RET(rh)", 0/*usb_pipein(pipe)*/);
-#else
-	mdelay(1);
-#endif
-
-	return stat;
-}
-
-/*-------------------------------------------------------------------------*/
-
-/* common code for handling submit messages - used for all but root hub */
-/* accesses. */
-int submit_common_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
-		int transfer_len, struct devrequest *setup, int interval)
-{
-	int stat = 0;
-	int maxsize = usb_maxpacket(dev, pipe);
-	int timeout;
-
-	/* device pulled? Shortcut the action. */
-	if (devgone == dev) {
-		dev->status = USB_ST_CRC_ERR;
-		return 0;
-	}
-
-#ifdef DEBUG
-	urb_priv.actual_length = 0;
-	pkt_print(dev, pipe, buffer, transfer_len, setup, "SUB", usb_pipein(pipe));
-#else
-	mdelay(1);
-#endif
-	if (!maxsize) {
-		err("submit_common_message: pipesize for pipe %lx is zero",
-			pipe);
-		return -1;
-	}
-
-	if (sohci_submit_job(dev, pipe, buffer, transfer_len, setup, interval) < 0) {
-		err("sohci_submit_job failed");
-		return -1;
-	}
-
-	mdelay(10);
-	/* ohci_dump_status(&gohci); */
-
-	/* allow more time for a BULK device to react - some are slow */
-#define BULK_TO	 5000	/* timeout in milliseconds */
-	if (usb_pipebulk(pipe))
-		timeout = BULK_TO;
-	else
-		timeout = 100;
-
-	timeout *= 4;
-	/* wait for it to complete */
-	for (;;) {
-		/* check whether the controller is done */
-		stat = hc_interrupt();
-		if (stat < 0) {
-			stat = USB_ST_CRC_ERR;
-			break;
-		}
-		if (stat >= 0 && stat != 0xff) {
-			/* 0xff is returned for an SF-interrupt */
-			break;
-		}
-		if (--timeout) {
-			udelay(250); /* mdelay(1); */
-		} else {
-			err("CTL:TIMEOUT ");
-			stat = USB_ST_CRC_ERR;
-			break;
-		}
-	}
-	/* we got an Root Hub Status Change interrupt */
-	if (got_rhsc) {
-#ifdef DEBUG
-		ohci_dump_roothub (&gohci, 1);
-#endif
-		got_rhsc = 0;
-		/* abuse timeout */
-		timeout = rh_check_port_status(&gohci);
-		if (timeout >= 0) {
-#if 0 /* this does nothing useful, but leave it here in case that changes */
-			/* the called routine adds 1 to the passed value */
-			usb_hub_port_connect_change(gohci.rh.dev, timeout - 1);
-#endif
-			/*
-			 * XXX
-			 * This is potentially dangerous because it assumes
-			 * that only one device is ever plugged in!
-			 */
-			devgone = dev;
-		}
-	}
-
-	dev->status = stat;
-	dev->act_len = transfer_len;
-
-#ifdef DEBUG
-	pkt_print(dev, pipe, buffer, transfer_len, setup, "RET(ctlr)", usb_pipein(pipe));
-#else
-	mdelay(1);
-#endif
-
-	/* free TDs in urb_priv */
-	urb_free_priv (&urb_priv);
-	return 0;
-}
-
-/* submit routines called from usb.c */
-int submit_bulk_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
-		int transfer_len)
-{
-	info("submit_bulk_msg");
-	return submit_common_msg(dev, pipe, buffer, transfer_len, NULL, 0);
-}
-
-int submit_control_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
-		int transfer_len, struct devrequest *setup)
-{
-	int maxsize = usb_maxpacket(dev, pipe);
-
-	info("submit_control_msg");
-#ifdef DEBUG
-	urb_priv.actual_length = 0;
-	pkt_print(dev, pipe, buffer, transfer_len, setup, "SUB", usb_pipein(pipe));
-#else
-	mdelay(1);
-#endif
-	if (!maxsize) {
-		err("submit_control_message: pipesize for pipe %lx is zero",
-			pipe);
-		return -1;
-	}
-	if (((pipe >> 8) & 0x7f) == gohci.rh.devnum) {
-		gohci.rh.dev = dev;
-		/* root hub - redirect */
-		return ohci_submit_rh_msg(dev, pipe, buffer, transfer_len,
-			setup);
-	}
-
-	return submit_common_msg(dev, pipe, buffer, transfer_len, setup, 0);
-}
-
-int submit_int_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
-		int transfer_len, int interval)
-{
-	info("submit_int_msg");
-	return -1;
-}
-
-/*-------------------------------------------------------------------------*
- * HC functions
- *-------------------------------------------------------------------------*/
-
-/* reset the HC and BUS */
-
-static int hc_reset (ohci_t *ohci)
-{
-	int timeout = 30;
-	int smm_timeout = 50; /* 0,5 sec */
-
-	if (readl (&ohci->regs->control) & OHCI_CTRL_IR) { /* SMM owns the HC */
-		writel (OHCI_OCR, &ohci->regs->cmdstatus); /* request ownership */
-		info("USB HC TakeOver from SMM");
-		while (readl (&ohci->regs->control) & OHCI_CTRL_IR) {
-			mdelay (10);
-			if (--smm_timeout == 0) {
-				err("USB HC TakeOver failed!");
-				return -1;
-			}
-		}
-	}
-
-	/* Disable HC interrupts */
-	writel (OHCI_INTR_MIE, &ohci->regs->intrdisable);
-
-	dbg("USB HC reset_hc usb-%s: ctrl = 0x%X ;",
-		ohci->slot_name,
-		readl (&ohci->regs->control));
-
-	/* Reset USB (needed by some controllers) */
-	writel (0, &ohci->regs->control);
-
-	/* HC Reset requires max 10 us delay */
-	writel (OHCI_HCR,  &ohci->regs->cmdstatus);
-	while ((readl (&ohci->regs->cmdstatus) & OHCI_HCR) != 0) {
-		if (--timeout == 0) {
-			err("USB HC reset timed out!");
-			return -1;
-		}
-		udelay (1);
-	}
-	return 0;
-}
-
-/*-------------------------------------------------------------------------*/
-
-/* Start an OHCI controller, set the BUS operational
- * enable interrupts
- * connect the virtual root hub */
-
-static int hc_start (ohci_t * ohci)
-{
-	__u32 mask;
-	unsigned int fminterval;
-
-	ohci->disabled = 1;
-
-	/* Tell the controller where the control and bulk lists are
-	 * The lists are empty now. */
-
-	writel (0, &ohci->regs->ed_controlhead);
-	writel (0, &ohci->regs->ed_bulkhead);
-
-	writel ((__u32)ohci->hcca, &ohci->regs->hcca); /* a reset clears this */
-
-	fminterval = 0x2edf;
-	writel ((fminterval * 9) / 10, &ohci->regs->periodicstart);
-	fminterval |= ((((fminterval - 210) * 6) / 7) << 16);
-	writel (fminterval, &ohci->regs->fminterval);
-	writel (0x628, &ohci->regs->lsthresh);
-
-	/* start controller operations */
-	ohci->hc_control = OHCI_CONTROL_INIT | OHCI_USB_OPER;
-	ohci->disabled = 0;
-	writel (ohci->hc_control, &ohci->regs->control);
-
-	/* disable all interrupts */
-	mask = (OHCI_INTR_SO | OHCI_INTR_WDH | OHCI_INTR_SF | OHCI_INTR_RD |
-			OHCI_INTR_UE | OHCI_INTR_FNO | OHCI_INTR_RHSC |
-			OHCI_INTR_OC | OHCI_INTR_MIE);
-	writel (mask, &ohci->regs->intrdisable);
-	/* clear all interrupts */
-	mask &= ~OHCI_INTR_MIE;
-	writel (mask, &ohci->regs->intrstatus);
-	/* Choose the interrupts we care about now  - but w/o MIE */
-	mask = OHCI_INTR_RHSC | OHCI_INTR_UE | OHCI_INTR_WDH | OHCI_INTR_SO;
-	writel (mask, &ohci->regs->intrenable);
-
-#ifdef	OHCI_USE_NPS
-	/* required for AMD-756 and some Mac platforms */
-	writel ((roothub_a (ohci) | RH_A_NPS) & ~RH_A_PSM,
-		&ohci->regs->roothub.a);
-	writel (RH_HS_LPSC, &ohci->regs->roothub.status);
-#endif	/* OHCI_USE_NPS */
-
-	/* POTPGT delay is bits 24-31, in 2 ms units. */
-	mdelay ((roothub_a (ohci) >> 23) & 0x1fe);
-
-	/* connect the virtual root hub */
-	ohci->rh.devnum = 0;
-
-	return 0;
-}
-
-/*-------------------------------------------------------------------------*/
-
-/* an interrupt happens */
-
-static int
-hc_interrupt (void)
-{
-	ohci_t *ohci = &gohci;
-	struct ohci_regs *regs = ohci->regs;
-	int ints;
-	int stat = -1;
-
-	if ((ohci->hcca->done_head != 0) && !(m32_swap (ohci->hcca->done_head) & 0x01)) {
-		ints =	OHCI_INTR_WDH;
-	} else {
-		ints = readl (&regs->intrstatus);
-	}
-
-	/* dbg("Interrupt: %x frame: %x", ints, le16_to_cpu (ohci->hcca->frame_no)); */
-
-	if (ints & OHCI_INTR_RHSC) {
-		got_rhsc = 1;
-	}
-
-	if (ints & OHCI_INTR_UE) {
-		ohci->disabled++;
-		err ("OHCI Unrecoverable Error, controller usb-%s disabled",
-			ohci->slot_name);
-		/* e.g. due to PCI Master/Target Abort */
-
-#ifdef	DEBUG
-		ohci_dump (ohci, 1);
-#else
-	mdelay(1);
-#endif
-		/* FIXME: be optimistic, hope that bug won't repeat often. */
-		/* Make some non-interrupt context restart the controller. */
-		/* Count and limit the retries though; either hardware or */
-		/* software errors can go forever... */
-		hc_reset (ohci);
-		return -1;
-	}
-
-	if (ints & OHCI_INTR_WDH) {
-		mdelay(1);
-		writel (OHCI_INTR_WDH, &regs->intrdisable);
-		stat = dl_done_list (&gohci, dl_reverse_done_list (&gohci));
-		writel (OHCI_INTR_WDH, &regs->intrenable);
-	}
-
-	if (ints & OHCI_INTR_SO) {
-		dbg("USB Schedule overrun\n");
-		writel (OHCI_INTR_SO, &regs->intrenable);
-		stat = -1;
-	}
-
-	/* FIXME:  this assumes SOF (1/ms) interrupts don't get lost... */
-	if (ints & OHCI_INTR_SF) {
-		unsigned int frame = m16_swap (ohci->hcca->frame_no) & 1;
-		mdelay(1);
-		writel (OHCI_INTR_SF, &regs->intrdisable);
-		if (ohci->ed_rm_list[frame] != NULL)
-			writel (OHCI_INTR_SF, &regs->intrenable);
-		stat = 0xff;
-	}
-
-	writel (ints, &regs->intrstatus);
-	return stat;
-}
-
-/*-------------------------------------------------------------------------*/
-
-/*-------------------------------------------------------------------------*/
-
-/* De-allocate all resources.. */
-
-static void hc_release_ohci (ohci_t *ohci)
-{
-	dbg ("USB HC release ohci usb-%s", ohci->slot_name);
-
-	if (!ohci->disabled)
-		hc_reset (ohci);
-}
-
-/*-------------------------------------------------------------------------*/
-
-#define __read_32bit_c0_register(source, sel)				\
-({ int __res;								\
-	if (sel == 0)							\
-		__asm__ __volatile__(					\
-			"mfc0\t%0, " #source "\n\t"			\
-			: "=r" (__res));				\
-	else								\
-		__asm__ __volatile__(					\
-			".set\tmips32\n\t"				\
-			"mfc0\t%0, " #source ", " #sel "\n\t"		\
-			".set\tmips0\n\t"				\
-			: "=r" (__res));				\
-	__res;								\
-})
-
-#define read_c0_prid()		__read_32bit_c0_register($15, 0)
-
-/*
- * low level initalisation routine, called from usb.c
- */
-static char ohci_inited = 0;
-
-int usb_lowlevel_init(int index, enum usb_init_type init, void **controller)
-{
-	u32 pin_func;
-	u32 sys_freqctrl, sys_clksrc;
-	u32 prid = read_c0_prid();
-
-	dbg("in usb_lowlevel_init\n");
-
-	/* zero and disable FREQ2 */
-	sys_freqctrl = au_readl(SYS_FREQCTRL0);
-	sys_freqctrl &= ~0xFFF00000;
-	au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
-	/* zero and disable USBH/USBD clocks */
-	sys_clksrc = au_readl(SYS_CLKSRC);
-	sys_clksrc &= ~0x00007FE0;
-	au_writel(sys_clksrc, SYS_CLKSRC);
-
-	sys_freqctrl = au_readl(SYS_FREQCTRL0);
-	sys_freqctrl &= ~0xFFF00000;
-
-	sys_clksrc = au_readl(SYS_CLKSRC);
-	sys_clksrc &= ~0x00007FE0;
-
-	switch (prid & 0x000000FF) {
-	case 0x00: /* DA */
-	case 0x01: /* HA */
-	case 0x02: /* HB */
-		/* CPU core freq to 48MHz to slow it way down... */
-		au_writel(4, SYS_CPUPLL);
-
-		/*
-		 * Setup 48MHz FREQ2 from CPUPLL for USB Host
-		 */
-		/* FRDIV2=3 -> div by 8 of 384MHz -> 48MHz */
-		sys_freqctrl |= ((3<<22) | (1<<21) | (0<<20));
-		au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
-		/* CPU core freq to 384MHz */
-		au_writel(0x20, SYS_CPUPLL);
-
-		printf("Au1000: 48MHz OHCI workaround enabled\n");
-		break;
-
-	default:  /* HC and newer */
-		/* FREQ2 = aux/2 = 48 MHz */
-		sys_freqctrl |= ((0<<22) | (1<<21) | (1<<20));
-		au_writel(sys_freqctrl, SYS_FREQCTRL0);
-		break;
-	}
-
-	/*
-	 * Route 48MHz FREQ2 into USB Host and/or Device
-	 */
-	sys_clksrc |= ((4<<12) | (0<<11) | (0<<10));
-	au_writel(sys_clksrc, SYS_CLKSRC);
-
-	/* configure pins GPIO[14:9] as GPIO */
-	pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x8080);
-
-	au_writel(pin_func, SYS_PINFUNC);
-	au_writel(0x2800, SYS_TRIOUTCLR);
-	au_writel(0x0030, SYS_OUTPUTCLR);
-
-	dbg("OHCI board setup complete\n");
-
-	/* enable host controller */
-	au_writel(USBH_ENABLE_CE, USB_HOST_CONFIG);
-	udelay(1000);
-	au_writel(USBH_ENABLE_INIT, USB_HOST_CONFIG);
-	udelay(1000);
-
-	/* wait for reset complete (read register twice; see au1500 errata) */
-	while (au_readl(USB_HOST_CONFIG),
-	       !(au_readl(USB_HOST_CONFIG) & USBH_ENABLE_RD))
-		udelay(1000);
-
-	dbg("OHCI clock running\n");
-
-	memset (&gohci, 0, sizeof (ohci_t));
-	memset (&urb_priv, 0, sizeof (urb_priv_t));
-
-	/* align the storage */
-	if ((__u32)&ghcca[0] & 0xff) {
-		err("HCCA not aligned!!");
-		return -1;
-	}
-	phcca = &ghcca[0];
-	info("aligned ghcca %p", phcca);
-	memset(&ohci_dev, 0, sizeof(struct ohci_device));
-	if ((__u32)&ohci_dev.ed[0] & 0x7) {
-		err("EDs not aligned!!");
-		return -1;
-	}
-	memset(gtd, 0, sizeof(td_t) * (NUM_TD + 1));
-	if ((__u32)gtd & 0x7) {
-		err("TDs not aligned!!");
-		return -1;
-	}
-	ptd = gtd;
-	gohci.hcca = phcca;
-	memset (phcca, 0, sizeof (struct ohci_hcca));
-
-	gohci.disabled = 1;
-	gohci.sleeping = 0;
-	gohci.irq = -1;
-	gohci.regs = (struct ohci_regs *)(USB_OHCI_BASE | 0xA0000000);
-
-	gohci.flags = 0;
-	gohci.slot_name = "au1x00";
-
-	dbg("OHCI revision: 0x%08x\n"
-	       "  RH: a: 0x%08x b: 0x%08x\n",
-	       readl(&gohci.regs->revision),
-	       readl(&gohci.regs->roothub.a), readl(&gohci.regs->roothub.b));
-
-	if (hc_reset (&gohci) < 0)
-		goto errout;
-
-	/* FIXME this is a second HC reset; why?? */
-	writel (gohci.hc_control = OHCI_USB_RESET, &gohci.regs->control);
-	mdelay (10);
-
-	if (hc_start (&gohci) < 0)
-		goto errout;
-
-#ifdef	DEBUG
-	ohci_dump (&gohci, 1);
-#else
-	mdelay(1);
-#endif
-	ohci_inited = 1;
-	return 0;
-
-  errout:
-	err("OHCI initialization error\n");
-	hc_release_ohci (&gohci);
-	/* Initialization failed */
-	au_writel(readl(USB_HOST_CONFIG) & ~USBH_ENABLE_CE, USB_HOST_CONFIG);
-	return -1;
-}
-
-int usb_lowlevel_stop(int index)
-{
-	/* this gets called really early - before the controller has */
-	/* even been initialized! */
-	if (!ohci_inited)
-		return 0;
-	/* TODO release any interrupts, etc. */
-	/* call hc_release_ohci() here ? */
-	hc_reset (&gohci);
-	/* may not want to do this */
-	/* Disable clock */
-	au_writel(readl(USB_HOST_CONFIG) & ~USBH_ENABLE_CE, USB_HOST_CONFIG);
-	return 0;
-}
-
-#endif /* CONFIG_USB_OHCI */
diff --git a/arch/mips/mach-au1x00/au1x00_usb_ohci.h b/arch/mips/mach-au1x00/au1x00_usb_ohci.h
deleted file mode 100644
index bb9f351..0000000
--- a/arch/mips/mach-au1x00/au1x00_usb_ohci.h
+++ /dev/null
@@ -1,416 +0,0 @@
-/*
- * URB OHCI HCD (Host Controller Driver) for USB.
- *
- * (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
- * (C) Copyright 2000-2001 David Brownell <dbrownell@users.sourceforge.net>
- *
- * usb-ohci.h
- */
-
-
-static int cc_to_error[16] = {
-
-/* mapping of the OHCI CC status to error codes */
-	/* No  Error  */	0,
-	/* CRC Error  */	USB_ST_CRC_ERR,
-	/* Bit Stuff  */	USB_ST_BIT_ERR,
-	/* Data Togg  */	USB_ST_CRC_ERR,
-	/* Stall      */	USB_ST_STALLED,
-	/* DevNotResp */	-1,
-	/* PIDCheck   */	USB_ST_BIT_ERR,
-	/* UnExpPID   */	USB_ST_BIT_ERR,
-	/* DataOver   */	USB_ST_BUF_ERR,
-	/* DataUnder  */	USB_ST_BUF_ERR,
-	/* reservd    */	-1,
-	/* reservd    */	-1,
-	/* BufferOver */	USB_ST_BUF_ERR,
-	/* BuffUnder  */	USB_ST_BUF_ERR,
-	/* Not Access */	-1,
-	/* Not Access */	-1
-};
-
-/* ED States */
-
-#define ED_NEW		0x00
-#define ED_UNLINK	0x01
-#define ED_OPER		0x02
-#define ED_DEL		0x04
-#define ED_URB_DEL	0x08
-
-/* usb_ohci_ed */
-struct ed {
-	__u32 hwINFO;
-	__u32 hwTailP;
-	__u32 hwHeadP;
-	__u32 hwNextED;
-
-	struct ed *ed_prev;
-	__u8 int_period;
-	__u8 int_branch;
-	__u8 int_load;
-	__u8 int_interval;
-	__u8 state;
-	__u8 type;
-	__u16 last_iso;
-	struct ed *ed_rm_list;
-
-	struct usb_device *usb_dev;
-	__u32 unused[3];
-} __attribute__((aligned(16)));
-typedef struct ed ed_t;
-
-
-/* TD info field */
-#define TD_CC			0xf0000000
-#define TD_CC_GET(td_p)		((td_p >>28) & 0x0f)
-#define TD_CC_SET(td_p, cc)	(td_p) = ((td_p) & 0x0fffffff) | (((cc) & 0x0f) << 28)
-#define TD_EC			0x0C000000
-#define TD_T			0x03000000
-#define TD_T_DATA0		0x02000000
-#define TD_T_DATA1		0x03000000
-#define TD_T_TOGGLE		0x00000000
-#define TD_R			0x00040000
-#define TD_DI			0x00E00000
-#define TD_DI_SET(X)		(((X) & 0x07)<< 21)
-#define TD_DP			0x00180000
-#define TD_DP_SETUP		0x00000000
-#define TD_DP_IN		0x00100000
-#define TD_DP_OUT		0x00080000
-
-#define TD_ISO			0x00010000
-#define TD_DEL			0x00020000
-
-/* CC Codes */
-#define TD_CC_NOERROR		0x00
-#define TD_CC_CRC		0x01
-#define TD_CC_BITSTUFFING	0x02
-#define TD_CC_DATATOGGLEM	0x03
-#define TD_CC_STALL		0x04
-#define TD_DEVNOTRESP		0x05
-#define TD_PIDCHECKFAIL		0x06
-#define TD_UNEXPECTEDPID	0x07
-#define TD_DATAOVERRUN		0x08
-#define TD_DATAUNDERRUN		0x09
-#define TD_BUFFEROVERRUN	0x0C
-#define TD_BUFFERUNDERRUN	0x0D
-#define TD_NOTACCESSED		0x0F
-
-
-#define MAXPSW 1
-
-struct td {
-	__u32 hwINFO;
-	__u32 hwCBP;		/* Current Buffer Pointer */
-	__u32 hwNextTD;		/* Next TD Pointer */
-	__u32 hwBE;		/* Memory Buffer End Pointer */
-
-	__u16 hwPSW[MAXPSW];
-	__u8 unused;
-	__u8 index;
-	struct ed *ed;
-	struct td *next_dl_td;
-	struct usb_device *usb_dev;
-	int transfer_len;
-	__u32 data;
-
-	__u32 unused2[2];
-} __attribute__((aligned(32)));
-typedef struct td td_t;
-
-#define OHCI_ED_SKIP	(1 << 14)
-
-/*
- * The HCCA (Host Controller Communications Area) is a 256 byte
- * structure defined in the OHCI spec. that the host controller is
- * told the base address of.  It must be 256-byte aligned.
- */
-
-#define NUM_INTS 32	/* part of the OHCI standard */
-struct ohci_hcca {
-	__u32	int_table[NUM_INTS];	/* Interrupt ED table */
-	__u16	frame_no;		/* current frame number */
-	__u16	pad1;			/* set to 0 on each frame_no change */
-	__u32	done_head;		/* info returned for an interrupt */
-	u8		reserved_for_hc[116];
-} __attribute__((aligned(256)));
-
-
-/*
- * Maximum number of root hub ports.
- */
-#define MAX_ROOT_PORTS	15	/* maximum OHCI root hub ports */
-
-/*
- * This is the structure of the OHCI controller's memory mapped I/O
- * region.  This is Memory Mapped I/O.	You must use the readl() and
- * writel() macros defined in asm/io.h to access these!!
- */
-struct ohci_regs {
-	/* control and status registers */
-	__u32	revision;
-	__u32	control;
-	__u32	cmdstatus;
-	__u32	intrstatus;
-	__u32	intrenable;
-	__u32	intrdisable;
-	/* memory pointers */
-	__u32	hcca;
-	__u32	ed_periodcurrent;
-	__u32	ed_controlhead;
-	__u32	ed_controlcurrent;
-	__u32	ed_bulkhead;
-	__u32	ed_bulkcurrent;
-	__u32	donehead;
-	/* frame counters */
-	__u32	fminterval;
-	__u32	fmremaining;
-	__u32	fmnumber;
-	__u32	periodicstart;
-	__u32	lsthresh;
-	/* Root hub ports */
-	struct	ohci_roothub_regs {
-		__u32	a;
-		__u32	b;
-		__u32	status;
-		__u32	portstatus[MAX_ROOT_PORTS];
-	} roothub;
-} __attribute__((aligned(32)));
-
-
-/* OHCI CONTROL AND STATUS REGISTER MASKS */
-
-/*
- * HcControl (control) register masks
- */
-#define OHCI_CTRL_CBSR	(3 << 0)	/* control/bulk service ratio */
-#define OHCI_CTRL_PLE	(1 << 2)	/* periodic list enable */
-#define OHCI_CTRL_IE	(1 << 3)	/* isochronous enable */
-#define OHCI_CTRL_CLE	(1 << 4)	/* control list enable */
-#define OHCI_CTRL_BLE	(1 << 5)	/* bulk list enable */
-#define OHCI_CTRL_HCFS	(3 << 6)	/* host controller functional state */
-#define OHCI_CTRL_IR	(1 << 8)	/* interrupt routing */
-#define OHCI_CTRL_RWC	(1 << 9)	/* remote wakeup connected */
-#define OHCI_CTRL_RWE	(1 << 10)	/* remote wakeup enable */
-
-/* pre-shifted values for HCFS */
-#	define OHCI_USB_RESET	(0 << 6)
-#	define OHCI_USB_RESUME	(1 << 6)
-#	define OHCI_USB_OPER	(2 << 6)
-#	define OHCI_USB_SUSPEND	(3 << 6)
-
-/*
- * HcCommandStatus (cmdstatus) register masks
- */
-#define OHCI_HCR	(1 << 0)	/* host controller reset */
-#define OHCI_CLF	(1 << 1)	/* control list filled */
-#define OHCI_BLF	(1 << 2)	/* bulk list filled */
-#define OHCI_OCR	(1 << 3)	/* ownership change request */
-#define OHCI_SOC	(3 << 16)	/* scheduling overrun count */
-
-/*
- * masks used with interrupt registers:
- * HcInterruptStatus (intrstatus)
- * HcInterruptEnable (intrenable)
- * HcInterruptDisable (intrdisable)
- */
-#define OHCI_INTR_SO	(1 << 0)	/* scheduling overrun */
-#define OHCI_INTR_WDH	(1 << 1)	/* writeback of done_head */
-#define OHCI_INTR_SF	(1 << 2)	/* start frame */
-#define OHCI_INTR_RD	(1 << 3)	/* resume detect */
-#define OHCI_INTR_UE	(1 << 4)	/* unrecoverable error */
-#define OHCI_INTR_FNO	(1 << 5)	/* frame number overflow */
-#define OHCI_INTR_RHSC	(1 << 6)	/* root hub status change */
-#define OHCI_INTR_OC	(1 << 30)	/* ownership change */
-#define OHCI_INTR_MIE	(1 << 31)	/* master interrupt enable */
-
-
-/* Virtual Root HUB */
-struct virt_root_hub {
-	int devnum; /* Address of Root Hub endpoint */
-	void *dev;  /* was urb */
-	void *int_addr;
-	int send;
-	int interval;
-};
-
-/* USB HUB CONSTANTS (not OHCI-specific; see hub.h) */
-
-/* destination of request */
-#define RH_INTERFACE		0x01
-#define RH_ENDPOINT		0x02
-#define RH_OTHER		0x03
-
-#define RH_CLASS		0x20
-#define RH_VENDOR		0x40
-
-/* Requests: bRequest << 8 | bmRequestType */
-#define RH_GET_STATUS		0x0080
-#define RH_CLEAR_FEATURE	0x0100
-#define RH_SET_FEATURE		0x0300
-#define RH_SET_ADDRESS		0x0500
-#define RH_GET_DESCRIPTOR	0x0680
-#define RH_SET_DESCRIPTOR	0x0700
-#define RH_GET_CONFIGURATION	0x0880
-#define RH_SET_CONFIGURATION	0x0900
-#define RH_GET_STATE		0x0280
-#define RH_GET_INTERFACE	0x0A80
-#define RH_SET_INTERFACE	0x0B00
-#define RH_SYNC_FRAME		0x0C80
-/* Our Vendor Specific Request */
-#define RH_SET_EP		0x2000
-
-
-/* Hub port features */
-#define RH_PORT_CONNECTION	0x00
-#define RH_PORT_ENABLE		0x01
-#define RH_PORT_SUSPEND		0x02
-#define RH_PORT_OVER_CURRENT	0x03
-#define RH_PORT_RESET		0x04
-#define RH_PORT_POWER		0x08
-#define RH_PORT_LOW_SPEED	0x09
-
-#define RH_C_PORT_CONNECTION	0x10
-#define RH_C_PORT_ENABLE	0x11
-#define RH_C_PORT_SUSPEND	0x12
-#define RH_C_PORT_OVER_CURRENT	0x13
-#define RH_C_PORT_RESET		0x14
-
-/* Hub features */
-#define RH_C_HUB_LOCAL_POWER	0x00
-#define RH_C_HUB_OVER_CURRENT	0x01
-
-#define RH_DEVICE_REMOTE_WAKEUP 0x00
-#define RH_ENDPOINT_STALL	0x01
-
-#define RH_ACK			0x01
-#define RH_REQ_ERR		-1
-#define RH_NACK			0x00
-
-
-/* OHCI ROOT HUB REGISTER MASKS */
-
-/* roothub.portstatus [i] bits */
-#define RH_PS_CCS		0x00000001	/* current connect status */
-#define RH_PS_PES		0x00000002	/* port enable status*/
-#define RH_PS_PSS		0x00000004	/* port suspend status */
-#define RH_PS_POCI		0x00000008	/* port over current indicator */
-#define RH_PS_PRS		0x00000010	/* port reset status */
-#define RH_PS_PPS		0x00000100	/* port power status */
-#define RH_PS_LSDA		0x00000200	/* low speed device attached */
-#define RH_PS_CSC		0x00010000	/* connect status change */
-#define RH_PS_PESC		0x00020000	/* port enable status change */
-#define RH_PS_PSSC		0x00040000	/* port suspend status change */
-#define RH_PS_OCIC		0x00080000	/* over current indicator change */
-#define RH_PS_PRSC		0x00100000	/* port reset status change */
-
-/* roothub.status bits */
-#define RH_HS_LPS		0x00000001	/* local power status */
-#define RH_HS_OCI		0x00000002	/* over current indicator */
-#define RH_HS_DRWE		0x00008000	/* device remote wakeup enable */
-#define RH_HS_LPSC		0x00010000	/* local power status change */
-#define RH_HS_OCIC		0x00020000	/* over current indicator change */
-#define RH_HS_CRWE		0x80000000	/* clear remote wakeup enable */
-
-/* roothub.b masks */
-#define RH_B_DR			0x0000ffff	/* device removable flags */
-#define RH_B_PPCM		0xffff0000	/* port power control mask */
-
-/* roothub.a masks */
-#define	RH_A_NDP		(0xff << 0)	/* number of downstream ports */
-#define	RH_A_PSM		(1 << 8)	/* power switching mode */
-#define	RH_A_NPS		(1 << 9)	/* no power switching */
-#define	RH_A_DT			(1 << 10)	/* device type (mbz) */
-#define	RH_A_OCPM		(1 << 11)	/* over current protection mode */
-#define	RH_A_NOCP		(1 << 12)	/* no over current protection */
-#define	RH_A_POTPGT		(0xff << 24)	/* power on to power good time */
-
-/* urb */
-#define N_URB_TD 48
-typedef struct
-{
-	ed_t *ed;
-	__u16 length;		/* number of tds associated with this request */
-	__u16 td_cnt;		/* number of tds already serviced */
-	int   state;
-	unsigned long pipe;
-	int actual_length;
-	td_t *td[N_URB_TD];	/* list pointer to all corresponding TDs associated with this request */
-} urb_priv_t;
-#define URB_DEL 1
-
-/*
- * This is the full ohci controller description
- *
- * Note how the "proper" USB information is just
- * a subset of what the full implementation needs. (Linus)
- */
-
-
-typedef struct ohci {
-	struct ohci_hcca *hcca;		/* hcca */
-	/*dma_addr_t hcca_dma;*/
-
-	int irq;
-	int disabled;			/* e.g. got a UE, we're hung */
-	int sleeping;
-	unsigned long flags;		/* for HC bugs */
-
-	struct ohci_regs *regs;		/* OHCI controller's memory */
-
-	ed_t *ed_rm_list[2];		/* lists of all endpoints to be removed */
-	ed_t *ed_bulktail;		/* last endpoint of bulk list */
-	ed_t *ed_controltail;		/* last endpoint of control list */
-	int intrstatus;
-	__u32 hc_control;		/* copy of the hc control reg */
-	struct usb_device *dev[32];
-	struct virt_root_hub rh;
-
-	const char	*slot_name;
-} ohci_t;
-
-#define NUM_EDS 8		/* num of preallocated endpoint descriptors */
-
-struct ohci_device {
-	ed_t	ed[NUM_EDS];
-	int ed_cnt;
-};
-
-/* hcd */
-/* endpoint */
-static int ep_link(ohci_t * ohci, ed_t * ed);
-static int ep_unlink(ohci_t * ohci, ed_t * ed);
-static ed_t * ep_add_ed(struct usb_device * usb_dev, unsigned long pipe);
-
-/*-------------------------------------------------------------------------*/
-
-/* we need more TDs than EDs */
-#define NUM_TD 64
-
-/* +1 so we can align the storage */
-td_t gtd[NUM_TD+1];
-/* pointers to aligned storage */
-td_t *ptd;
-
-/* TDs ... */
-static inline struct td *
-td_alloc (struct usb_device *usb_dev)
-{
-	int i;
-	struct td	*td;
-
-	td = NULL;
-	for (i = 0; i < NUM_TD; i++) {
-		if (ptd[i].usb_dev == NULL) {
-			td = &ptd[i];
-			td->usb_dev = usb_dev;
-			break;
-		}
-	}
-	return td;
-}
-
-static inline void
-ed_free (struct ed *ed)
-{
-	ed->usb_dev = NULL;
-}
diff --git a/arch/mips/mach-au1x00/include/mach/au1x00.h b/arch/mips/mach-au1x00/include/mach/au1x00.h
deleted file mode 100644
index 1fabcba..0000000
--- a/arch/mips/mach-au1x00/include/mach/au1x00.h
+++ /dev/null
@@ -1,1040 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- *
- * BRIEF MODULE DESCRIPTION
- *	Include file for Alchemy Semiconductor's Au1k CPU.
- *
- * Copyright 2000,2001 MontaVista Software Inc.
- * Author: MontaVista Software, Inc.
- *	   ppopov@mvista.com or source@mvista.com
- */
-
- /*
-  * some definitions add by takuzo@sm.sony.co.jp and sato@sm.sony.co.jp
-  */
-
-#ifndef _AU1X00_H_
-#define _AU1X00_H_
-
-#ifndef __ASSEMBLY__
-/* cpu pipeline flush */
-void static inline au_sync(void)
-{
-	__asm__ volatile ("sync");
-}
-
-void static inline au_sync_udelay(int us)
-{
-	__asm__ volatile ("sync");
-	udelay(us);
-}
-
-void static inline au_writeb(u8 val, int reg)
-{
-	*(volatile u8 *)(reg) = val;
-}
-
-void static inline au_writew(u16 val, int reg)
-{
-	*(volatile u16 *)(reg) = val;
-}
-
-void static inline au_writel(u32 val, int reg)
-{
-	*(volatile u32 *)(reg) = val;
-}
-
-static inline u8 au_readb(unsigned long port)
-{
-	return (*(volatile u8 *)port);
-}
-
-static inline u16 au_readw(unsigned long port)
-{
-	return (*(volatile u16 *)port);
-}
-
-static inline u32 au_readl(unsigned long port)
-{
-	return (*(volatile u32 *)port);
-}
-
-/* These next three functions should be a generic part of the MIPS
- * kernel (with the 'au_' removed from the name) and selected for
- * processors that support the instructions.
- * Taken from PPC tree.  -- Dan
- */
-/* Return the bit position of the most significant 1 bit in a word */
-static __inline__ int __ilog2(unsigned int x)
-{
-	int lz;
-
-	asm volatile (
-		".set\tnoreorder\n\t"
-		".set\tnoat\n\t"
-		".set\tmips32\n\t"
-		"clz\t%0,%1\n\t"
-		".set\tmips0\n\t"
-		".set\tat\n\t"
-		".set\treorder"
-		: "=r" (lz)
-		: "r" (x));
-
-	return 31 - lz;
-}
-
-static __inline__ int au_ffz(unsigned int x)
-{
-	if ((x = ~x) == 0)
-		return 32;
-	return __ilog2(x & -x);
-}
-
-/*
- * ffs: find first bit set. This is defined the same way as
- * the libc and compiler builtin ffs routines, therefore
- * differs in spirit from the above ffz (man ffs).
- */
-static __inline__ int au_ffs(int x)
-{
-	return __ilog2(x & -x) + 1;
-}
-
-#define gpio_set(Value)      outl(Value, SYS_OUTPUTSET)
-#define gpio_clear(Value)    outl(Value, SYS_OUTPUTCLR)
-#define gpio_read()          inl(SYS_PINSTATERD)
-#define gpio_tristate(Value) outl(Value, SYS_TRIOUTCLR)
-
-#endif /* !ASSEMBLY */
-
-#ifdef CONFIG_PM
-/* no CP0 timer irq */
-#define ALLINTS (IE_IRQ0 | IE_IRQ1 | IE_IRQ2 | IE_IRQ3 | IE_IRQ4)
-#else
-#define ALLINTS (IE_IRQ0 | IE_IRQ1 | IE_IRQ2 | IE_IRQ3 | IE_IRQ4 | IE_IRQ5)
-#endif
-
-#define CP0_IWATCHLO		$18,1
-#define CP0_DEBUG		$23
-
-/* SDRAM Controller */
-#define MEM_SDMODE0                0xB4000000
-#define MEM_SDMODE1                0xB4000004
-#define MEM_SDMODE2                0xB4000008
-
-#define MEM_SDADDR0                0xB400000C
-#define MEM_SDADDR1                0xB4000010
-#define MEM_SDADDR2                0xB4000014
-
-#define MEM_SDREFCFG               0xB4000018
-#define MEM_SDPRECMD               0xB400001C
-#define MEM_SDAUTOREF              0xB4000020
-
-#define MEM_SDWRMD0                0xB4000024
-#define MEM_SDWRMD1                0xB4000028
-#define MEM_SDWRMD2                0xB400002C
-
-#define MEM_SDSLEEP                0xB4000030
-#define MEM_SDSMCKE                0xB4000034
-
-/* Static Bus Controller */
-#define MEM_STCFG0                 0xB4001000
-#define MEM_STTIME0                0xB4001004
-#define MEM_STADDR0                0xB4001008
-
-#define MEM_STCFG1                 0xB4001010
-#define MEM_STTIME1                0xB4001014
-#define MEM_STADDR1                0xB4001018
-
-#define MEM_STCFG2                 0xB4001020
-#define MEM_STTIME2                0xB4001024
-#define MEM_STADDR2                0xB4001028
-
-#define MEM_STCFG3                 0xB4001030
-#define MEM_STTIME3                0xB4001034
-#define MEM_STADDR3                0xB4001038
-
-/* Interrupt Controller 0 */
-#define IC0_CFG0RD                 0xB0400040
-#define IC0_CFG0SET                0xB0400040
-#define IC0_CFG0CLR                0xB0400044
-
-#define IC0_CFG1RD                 0xB0400048
-#define IC0_CFG1SET                0xB0400048
-#define IC0_CFG1CLR                0xB040004C
-
-#define IC0_CFG2RD                 0xB0400050
-#define IC0_CFG2SET                0xB0400050
-#define IC0_CFG2CLR                0xB0400054
-
-#define IC0_REQ0INT                0xB0400054
-#define IC0_SRCRD                  0xB0400058
-#define IC0_SRCSET                 0xB0400058
-#define IC0_SRCCLR                 0xB040005C
-#define IC0_REQ1INT                0xB040005C
-
-#define IC0_ASSIGNRD               0xB0400060
-#define IC0_ASSIGNSET              0xB0400060
-#define IC0_ASSIGNCLR              0xB0400064
-
-#define IC0_WAKERD                 0xB0400068
-#define IC0_WAKESET                0xB0400068
-#define IC0_WAKECLR                0xB040006C
-
-#define IC0_MASKRD                 0xB0400070
-#define IC0_MASKSET                0xB0400070
-#define IC0_MASKCLR                0xB0400074
-
-#define IC0_RISINGRD               0xB0400078
-#define IC0_RISINGCLR              0xB0400078
-#define IC0_FALLINGRD              0xB040007C
-#define IC0_FALLINGCLR             0xB040007C
-
-#define IC0_TESTBIT                0xB0400080
-
-/* Interrupt Controller 1 */
-#define IC1_CFG0RD                 0xB1800040
-#define IC1_CFG0SET                0xB1800040
-#define IC1_CFG0CLR                0xB1800044
-
-#define IC1_CFG1RD                 0xB1800048
-#define IC1_CFG1SET                0xB1800048
-#define IC1_CFG1CLR                0xB180004C
-
-#define IC1_CFG2RD                 0xB1800050
-#define IC1_CFG2SET                0xB1800050
-#define IC1_CFG2CLR                0xB1800054
-
-#define IC1_REQ0INT                0xB1800054
-#define IC1_SRCRD                  0xB1800058
-#define IC1_SRCSET                 0xB1800058
-#define IC1_SRCCLR                 0xB180005C
-#define IC1_REQ1INT                0xB180005C
-
-#define IC1_ASSIGNRD               0xB1800060
-#define IC1_ASSIGNSET              0xB1800060
-#define IC1_ASSIGNCLR              0xB1800064
-
-#define IC1_WAKERD                 0xB1800068
-#define IC1_WAKESET                0xB1800068
-#define IC1_WAKECLR                0xB180006C
-
-#define IC1_MASKRD                 0xB1800070
-#define IC1_MASKSET                0xB1800070
-#define IC1_MASKCLR                0xB1800074
-
-#define IC1_RISINGRD               0xB1800078
-#define IC1_RISINGCLR              0xB1800078
-#define IC1_FALLINGRD              0xB180007C
-#define IC1_FALLINGCLR             0xB180007C
-
-#define IC1_TESTBIT                0xB1800080
-
-/* Interrupt Configuration Modes */
-#define INTC_INT_DISABLED                0
-#define INTC_INT_RISE_EDGE             0x1
-#define INTC_INT_FALL_EDGE             0x2
-#define INTC_INT_RISE_AND_FALL_EDGE    0x3
-#define INTC_INT_HIGH_LEVEL            0x5
-#define INTC_INT_LOW_LEVEL             0x6
-#define INTC_INT_HIGH_AND_LOW_LEVEL    0x7
-
-/* Interrupt Numbers */
-#define AU1X00_UART0_INT          0
-#define AU1000_UART1_INT          1 /* au1000 */
-#define AU1000_UART2_INT          2 /* au1000 */
-
-#define AU1500_PCI_INTA           1 /* au1500 */
-#define AU1500_PCI_INTB           2 /* au1500 */
-
-#define AU1X00_UART3_INT          3
-
-#define AU1000_SSI0_INT           4 /* au1000 */
-#define AU1000_SSI1_INT           5 /* au1000 */
-
-#define AU1500_PCI_INTC           4 /* au1500 */
-#define AU1500_PCI_INTD           5 /* au1500 */
-
-#define AU1X00_DMA_INT_BASE       6
-#define AU1X00_TOY_INT            14
-#define AU1X00_TOY_MATCH0_INT     15
-#define AU1X00_TOY_MATCH1_INT     16
-#define AU1X00_TOY_MATCH2_INT     17
-#define AU1X00_RTC_INT            18
-#define AU1X00_RTC_MATCH0_INT     19
-#define AU1X00_RTC_MATCH1_INT     20
-#define AU1X00_RTC_MATCH2_INT     21
-#define AU1000_IRDA_TX_INT        22 /* au1000 */
-#define AU1000_IRDA_RX_INT        23 /* au1000 */
-#define AU1X00_USB_DEV_REQ_INT    24
-#define AU1X00_USB_DEV_SUS_INT    25
-#define AU1X00_USB_HOST_INT       26
-#define AU1X00_ACSYNC_INT         27
-#define AU1X00_MAC0_DMA_INT       28
-#define AU1X00_MAC1_DMA_INT       29
-#define AU1X00_ETH0_IRQ           AU1X00_MAC0_DMA_INT
-#define AU1X00_ETH1_IRQ           AU1X00_MAC1_DMA_INT
-#define AU1000_I2S_UO_INT         30 /* au1000 */
-#define AU1X00_AC97C_INT          31
-#define AU1X00_LAST_INTC0_INT     AU1X00_AC97C_INT
-#define AU1X00_GPIO_0             32
-#define AU1X00_GPIO_1             33
-#define AU1X00_GPIO_2             34
-#define AU1X00_GPIO_3             35
-#define AU1X00_GPIO_4             36
-#define AU1X00_GPIO_5             37
-#define AU1X00_GPIO_6             38
-#define AU1X00_GPIO_7             39
-#define AU1X00_GPIO_8             40
-#define AU1X00_GPIO_9             41
-#define AU1X00_GPIO_10            42
-#define AU1X00_GPIO_11            43
-#define AU1X00_GPIO_12            44
-#define AU1X00_GPIO_13            45
-#define AU1X00_GPIO_14            46
-#define AU1X00_GPIO_15            47
-
-/* Au1000 only */
-#define AU1000_GPIO_16            48
-#define AU1000_GPIO_17            49
-#define AU1000_GPIO_18            50
-#define AU1000_GPIO_19            51
-#define AU1000_GPIO_20            52
-#define AU1000_GPIO_21            53
-#define AU1000_GPIO_22            54
-#define AU1000_GPIO_23            55
-#define AU1000_GPIO_24            56
-#define AU1000_GPIO_25            57
-#define AU1000_GPIO_26            58
-#define AU1000_GPIO_27            59
-#define AU1000_GPIO_28            60
-#define AU1000_GPIO_29            61
-#define AU1000_GPIO_30            62
-#define AU1000_GPIO_31            63
-
-/* Au1500 only */
-#define AU1500_GPIO_200           48
-#define AU1500_GPIO_201           49
-#define AU1500_GPIO_202           50
-#define AU1500_GPIO_203           51
-#define AU1500_GPIO_20            52
-#define AU1500_GPIO_204           53
-#define AU1500_GPIO_205           54
-#define AU1500_GPIO_23            55
-#define AU1500_GPIO_24            56
-#define AU1500_GPIO_25            57
-#define AU1500_GPIO_26            58
-#define AU1500_GPIO_27            59
-#define AU1500_GPIO_28            60
-#define AU1500_GPIO_206           61
-#define AU1500_GPIO_207           62
-#define AU1500_GPIO_208_215       63
-
-#define AU1X00_MAX_INTR           63
-
-#define AU1100_SD		2
-#define	AU1100_GPIO_208_215	29
-/* REDEFINE SECONDARY GPIO BLOCK INTO IC1 CONTROLLER HERE */
-
-/* Programmable Counters 0 and 1 */
-#define SYS_BASE                   0xB1900000
-#define SYS_COUNTER_CNTRL          (SYS_BASE + 0x14)
-#define SYS_CNTRL_E1S            (1<<23)
-#define SYS_CNTRL_T1S            (1<<20)
-#define SYS_CNTRL_M21            (1<<19)
-#define SYS_CNTRL_M11            (1<<18)
-#define SYS_CNTRL_M01            (1<<17)
-#define SYS_CNTRL_C1S            (1<<16)
-#define SYS_CNTRL_BP             (1<<14)
-#define SYS_CNTRL_EN1            (1<<13)
-#define SYS_CNTRL_BT1            (1<<12)
-#define SYS_CNTRL_EN0            (1<<11)
-#define SYS_CNTRL_BT0            (1<<10)
-#define SYS_CNTRL_E0             (1<<8)
-#define SYS_CNTRL_E0S            (1<<7)
-#define SYS_CNTRL_32S            (1<<5)
-#define SYS_CNTRL_T0S            (1<<4)
-#define SYS_CNTRL_M20            (1<<3)
-#define SYS_CNTRL_M10            (1<<2)
-#define SYS_CNTRL_M00            (1<<1)
-#define SYS_CNTRL_C0S            (1<<0)
-
-/* Programmable Counter 0 Registers */
-#define SYS_TOYTRIM                 (SYS_BASE + 0)
-#define SYS_TOYWRITE                (SYS_BASE + 4)
-#define SYS_TOYMATCH0               (SYS_BASE + 8)
-#define SYS_TOYMATCH1               (SYS_BASE + 0xC)
-#define SYS_TOYMATCH2               (SYS_BASE + 0x10)
-#define SYS_TOYREAD                 (SYS_BASE + 0x40)
-
-/* Programmable Counter 1 Registers */
-#define SYS_RTCTRIM                 (SYS_BASE + 0x44)
-#define SYS_RTCWRITE                (SYS_BASE + 0x48)
-#define SYS_RTCMATCH0               (SYS_BASE + 0x4C)
-#define SYS_RTCMATCH1               (SYS_BASE + 0x50)
-#define SYS_RTCMATCH2               (SYS_BASE + 0x54)
-#define SYS_RTCREAD                 (SYS_BASE + 0x58)
-
-/* I2S Controller */
-#define I2S_DATA                    0xB1000000
-#define I2S_DATA_MASK        (0xffffff)
-#define I2S_CONFIG                0xB1000004
-#define I2S_CONFIG_XU        (1<<25)
-#define I2S_CONFIG_XO        (1<<24)
-#define I2S_CONFIG_RU        (1<<23)
-#define I2S_CONFIG_RO        (1<<22)
-#define I2S_CONFIG_TR        (1<<21)
-#define I2S_CONFIG_TE        (1<<20)
-#define I2S_CONFIG_TF        (1<<19)
-#define I2S_CONFIG_RR        (1<<18)
-#define I2S_CONFIG_RE        (1<<17)
-#define I2S_CONFIG_RF        (1<<16)
-#define I2S_CONFIG_PD        (1<<11)
-#define I2S_CONFIG_LB        (1<<10)
-#define I2S_CONFIG_IC        (1<<9)
-#define I2S_CONFIG_FM_BIT    7
-#define I2S_CONFIG_FM_MASK     (0x3 << I2S_CONFIG_FM_BIT)
-#define I2S_CONFIG_FM_I2S    (0x0 << I2S_CONFIG_FM_BIT)
-#define I2S_CONFIG_FM_LJ     (0x1 << I2S_CONFIG_FM_BIT)
-#define I2S_CONFIG_FM_RJ     (0x2 << I2S_CONFIG_FM_BIT)
-#define I2S_CONFIG_TN        (1<<6)
-#define I2S_CONFIG_RN        (1<<5)
-#define I2S_CONFIG_SZ_BIT    0
-#define I2S_CONFIG_SZ_MASK     (0x1F << I2S_CONFIG_SZ_BIT)
-
-#define I2S_CONTROL                0xB1000008
-#define I2S_CONTROL_D         (1<<1)
-#define I2S_CONTROL_CE        (1<<0)
-
-/* USB Host Controller */
-/* We pass USB_OHCI_BASE to ioremap, so it needs to be a physical address */
-#define USB_OHCI_BASE             0x10100000
-#define USB_OHCI_LEN              0x00100000
-#define USB_HOST_CONFIG           0xB017fffc
-
-/* USB Device Controller */
-#define USBD_EP0RD                0xB0200000
-#define USBD_EP0WR                0xB0200004
-#define USBD_EP2WR                0xB0200008
-#define USBD_EP3WR                0xB020000C
-#define USBD_EP4RD                0xB0200010
-#define USBD_EP5RD                0xB0200014
-#define USBD_INTEN                0xB0200018
-#define USBD_INTSTAT              0xB020001C
-#define USBDEV_INT_SOF       (1<<12)
-#define USBDEV_INT_HF_BIT    6
-#define USBDEV_INT_HF_MASK   (0x3f << USBDEV_INT_HF_BIT)
-#define USBDEV_INT_CMPLT_BIT  0
-#define USBDEV_INT_CMPLT_MASK (0x3f << USBDEV_INT_CMPLT_BIT)
-#define USBD_CONFIG               0xB0200020
-#define USBD_EP0CS                0xB0200024
-#define USBD_EP2CS                0xB0200028
-#define USBD_EP3CS                0xB020002C
-#define USBD_EP4CS                0xB0200030
-#define USBD_EP5CS                0xB0200034
-#define USBDEV_CS_SU         (1<<14)
-#define USBDEV_CS_NAK        (1<<13)
-#define USBDEV_CS_ACK        (1<<12)
-#define USBDEV_CS_BUSY       (1<<11)
-#define USBDEV_CS_TSIZE_BIT  1
-#define USBDEV_CS_TSIZE_MASK (0x3ff << USBDEV_CS_TSIZE_BIT)
-#define USBDEV_CS_STALL      (1<<0)
-#define USBD_EP0RDSTAT            0xB0200040
-#define USBD_EP0WRSTAT            0xB0200044
-#define USBD_EP2WRSTAT            0xB0200048
-#define USBD_EP3WRSTAT            0xB020004C
-#define USBD_EP4RDSTAT            0xB0200050
-#define USBD_EP5RDSTAT            0xB0200054
-#define USBDEV_FSTAT_FLUSH     (1<<6)
-#define USBDEV_FSTAT_UF        (1<<5)
-#define USBDEV_FSTAT_OF        (1<<4)
-#define USBDEV_FSTAT_FCNT_BIT  0
-#define USBDEV_FSTAT_FCNT_MASK (0x0f << USBDEV_FSTAT_FCNT_BIT)
-#define USBD_ENABLE               0xB0200058
-#define USBDEV_ENABLE (1<<1)
-#define USBDEV_CE     (1<<0)
-
-/* Ethernet Controllers  */
-#define AU1000_ETH0_BASE          0xB0500000
-#define AU1000_ETH1_BASE          0xB0510000
-#define AU1500_ETH0_BASE	  0xB1500000
-#define AU1500_ETH1_BASE	  0xB1510000
-#define AU1100_ETH0_BASE	  0xB0500000
-
-/* 4 byte offsets from AU1000_ETH_BASE */
-#define MAC_CONTROL                     0x0
-#define MAC_RX_ENABLE               (1<<2)
-#define MAC_TX_ENABLE               (1<<3)
-#define MAC_DEF_CHECK               (1<<5)
-#define MAC_SET_BL(X)       (((X)&0x3)<<6)
-#define MAC_AUTO_PAD                (1<<8)
-#define MAC_DISABLE_RETRY          (1<<10)
-#define MAC_DISABLE_BCAST          (1<<11)
-#define MAC_LATE_COL               (1<<12)
-#define MAC_HASH_MODE              (1<<13)
-#define MAC_HASH_ONLY              (1<<15)
-#define MAC_PASS_ALL               (1<<16)
-#define MAC_INVERSE_FILTER         (1<<17)
-#define MAC_PROMISCUOUS            (1<<18)
-#define MAC_PASS_ALL_MULTI         (1<<19)
-#define MAC_FULL_DUPLEX            (1<<20)
-#define MAC_NORMAL_MODE                 0
-#define MAC_INT_LOOPBACK           (1<<21)
-#define MAC_EXT_LOOPBACK           (1<<22)
-#define MAC_DISABLE_RX_OWN         (1<<23)
-#define MAC_BIG_ENDIAN             (1<<30)
-#define MAC_RX_ALL                 (1<<31)
-#define MAC_ADDRESS_HIGH                0x4
-#define MAC_ADDRESS_LOW                 0x8
-#define MAC_MCAST_HIGH                  0xC
-#define MAC_MCAST_LOW                  0x10
-#define MAC_MII_CNTRL                  0x14
-#define MAC_MII_BUSY                (1<<0)
-#define MAC_MII_READ                     0
-#define MAC_MII_WRITE               (1<<1)
-#define MAC_SET_MII_SELECT_REG(X)   (((X)&0x1f)<<6)
-#define MAC_SET_MII_SELECT_PHY(X)   (((X)&0x1f)<<11)
-#define MAC_MII_DATA                   0x18
-#define MAC_FLOW_CNTRL                 0x1C
-#define MAC_FLOW_CNTRL_BUSY         (1<<0)
-#define MAC_FLOW_CNTRL_ENABLE       (1<<1)
-#define MAC_PASS_CONTROL            (1<<2)
-#define MAC_SET_PAUSE(X)        (((X)&0xffff)<<16)
-#define MAC_VLAN1_TAG                  0x20
-#define MAC_VLAN2_TAG                  0x24
-
-/* Ethernet Controller Enable */
-#define AU1000_MAC0_ENABLE       0xB0520000
-#define AU1000_MAC1_ENABLE       0xB0520004
-#define AU1500_MAC0_ENABLE       0xB1520000
-#define AU1500_MAC1_ENABLE       0xB1520004
-#define AU1100_MAC0_ENABLE       0xB0520000
-
-#define MAC_EN_CLOCK_ENABLE         (1<<0)
-#define MAC_EN_RESET0               (1<<1)
-#define MAC_EN_TOSS                 (0<<2)
-#define MAC_EN_CACHEABLE            (1<<3)
-#define MAC_EN_RESET1               (1<<4)
-#define MAC_EN_RESET2               (1<<5)
-#define MAC_DMA_RESET               (1<<6)
-
-/* Ethernet Controller DMA Channels */
-
-#define MAC0_TX_DMA_ADDR         0xB4004000
-#define MAC1_TX_DMA_ADDR         0xB4004200
-/* offsets from MAC_TX_RING_ADDR address */
-#define MAC_TX_BUFF0_STATUS             0x0
-#define TX_FRAME_ABORTED            (1<<0)
-#define TX_JAB_TIMEOUT              (1<<1)
-#define TX_NO_CARRIER               (1<<2)
-#define TX_LOSS_CARRIER             (1<<3)
-#define TX_EXC_DEF                  (1<<4)
-#define TX_LATE_COLL_ABORT          (1<<5)
-#define TX_EXC_COLL                 (1<<6)
-#define TX_UNDERRUN                 (1<<7)
-#define TX_DEFERRED                 (1<<8)
-#define TX_LATE_COLL                (1<<9)
-#define TX_COLL_CNT_MASK         (0xF<<10)
-#define TX_PKT_RETRY               (1<<31)
-#define MAC_TX_BUFF0_ADDR                0x4
-#define TX_DMA_ENABLE               (1<<0)
-#define TX_T_DONE                   (1<<1)
-#define TX_GET_DMA_BUFFER(X)    (((X)>>2)&0x3)
-#define MAC_TX_BUFF0_LEN                 0x8
-#define MAC_TX_BUFF1_STATUS             0x10
-#define MAC_TX_BUFF1_ADDR               0x14
-#define MAC_TX_BUFF1_LEN                0x18
-#define MAC_TX_BUFF2_STATUS             0x20
-#define MAC_TX_BUFF2_ADDR               0x24
-#define MAC_TX_BUFF2_LEN                0x28
-#define MAC_TX_BUFF3_STATUS             0x30
-#define MAC_TX_BUFF3_ADDR               0x34
-#define MAC_TX_BUFF3_LEN                0x38
-
-#define MAC0_RX_DMA_ADDR         0xB4004100
-#define MAC1_RX_DMA_ADDR         0xB4004300
-/* offsets from MAC_RX_RING_ADDR */
-#define MAC_RX_BUFF0_STATUS              0x0
-#define RX_FRAME_LEN_MASK           0x3fff
-#define RX_WDOG_TIMER              (1<<14)
-#define RX_RUNT                    (1<<15)
-#define RX_OVERLEN                 (1<<16)
-#define RX_COLL                    (1<<17)
-#define RX_ETHER                   (1<<18)
-#define RX_MII_ERROR               (1<<19)
-#define RX_DRIBBLING               (1<<20)
-#define RX_CRC_ERROR               (1<<21)
-#define RX_VLAN1                   (1<<22)
-#define RX_VLAN2                   (1<<23)
-#define RX_LEN_ERROR               (1<<24)
-#define RX_CNTRL_FRAME             (1<<25)
-#define RX_U_CNTRL_FRAME           (1<<26)
-#define RX_MCAST_FRAME             (1<<27)
-#define RX_BCAST_FRAME             (1<<28)
-#define RX_FILTER_FAIL             (1<<29)
-#define RX_PACKET_FILTER           (1<<30)
-#define RX_MISSED_FRAME            (1<<31)
-
-#define RX_ERROR (RX_WDOG_TIMER | RX_RUNT | RX_OVERLEN |  \
-		    RX_COLL | RX_MII_ERROR | RX_CRC_ERROR | \
-		    RX_LEN_ERROR | RX_U_CNTRL_FRAME | RX_MISSED_FRAME)
-#define MAC_RX_BUFF0_ADDR                0x4
-#define RX_DMA_ENABLE               (1<<0)
-#define RX_T_DONE                   (1<<1)
-#define RX_GET_DMA_BUFFER(X)    (((X)>>2)&0x3)
-#define RX_SET_BUFF_ADDR(X)     ((X)&0xffffffc0)
-#define MAC_RX_BUFF1_STATUS              0x10
-#define MAC_RX_BUFF1_ADDR                0x14
-#define MAC_RX_BUFF2_STATUS              0x20
-#define MAC_RX_BUFF2_ADDR                0x24
-#define MAC_RX_BUFF3_STATUS              0x30
-#define MAC_RX_BUFF3_ADDR                0x34
-
-
-/* UARTS 0-3 */
-#define UART0_ADDR                0xB1100000
-#define UART1_ADDR                0xB1200000
-#define UART2_ADDR                0xB1300000
-#define UART3_ADDR                0xB1400000
-#define UART_BASE                 UART0_ADDR
-#define UART_DEBUG_BASE           UART2_ADDR
-
-#define UART_RX		0	/* Receive buffer */
-#define UART_TX		4	/* Transmit buffer */
-#define UART_IER	8	/* Interrupt Enable Register */
-#define UART_IIR	0xC	/* Interrupt ID Register */
-#define UART_FCR	0x10	/* FIFO Control Register */
-#define UART_LCR	0x14	/* Line Control Register */
-#define UART_MCR	0x18	/* Modem Control Register */
-#define UART_LSR	0x1C	/* Line Status Register */
-#define UART_MSR	0x20	/* Modem Status Register */
-#define UART_CLK	0x28	/* Baud Rate Clock Divider */
-#define UART_ENABLE	0x100	/* Uart enable */
-
-#define UART_EN_CE      1       /* Clock enable */
-#define UART_EN_E       2       /* Enable */
-
-#define UART_FCR_ENABLE_FIFO	0x01 /* Enable the FIFO */
-#define UART_FCR_CLEAR_RCVR	0x02 /* Clear the RCVR FIFO */
-#define UART_FCR_CLEAR_XMIT	0x04 /* Clear the XMIT FIFO */
-#define UART_FCR_DMA_SELECT	0x08 /* For DMA applications */
-#define UART_FCR_TRIGGER_MASK	0xF0 /* Mask for the FIFO trigger range */
-#define UART_FCR_R_TRIGGER_1	0x00 /* Mask for receive trigger set at 1 */
-#define UART_FCR_R_TRIGGER_4	0x40 /* Mask for receive trigger set at 4 */
-#define UART_FCR_R_TRIGGER_8	0x80 /* Mask for receive trigger set at 8 */
-#define UART_FCR_R_TRIGGER_14   0xA0 /* Mask for receive trigger set at 14 */
-#define UART_FCR_T_TRIGGER_0	0x00 /* Mask for transmit trigger set at 0 */
-#define UART_FCR_T_TRIGGER_4	0x10 /* Mask for transmit trigger set at 4 */
-#define UART_FCR_T_TRIGGER_8    0x20 /* Mask for transmit trigger set at 8 */
-#define UART_FCR_T_TRIGGER_12	0x30 /* Mask for transmit trigger set at 12 */
-
-/*
- * These are the definitions for the Line Control Register
- */
-#define UART_LCR_SBC	0x40	/* Set break control */
-#define UART_LCR_SPAR	0x20	/* Stick parity (?) */
-#define UART_LCR_EPAR	0x10	/* Even parity select */
-#define UART_LCR_PARITY	0x08	/* Parity Enable */
-#define UART_LCR_STOP	0x04	/* Stop bits: 0=1 stop bit, 1= 2 stop bits */
-#define UART_LCR_WLEN5  0x00	/* Wordlength: 5 bits */
-#define UART_LCR_WLEN6  0x01	/* Wordlength: 6 bits */
-#define UART_LCR_WLEN7  0x02	/* Wordlength: 7 bits */
-#define UART_LCR_WLEN8  0x03	/* Wordlength: 8 bits */
-
-/*
- * These are the definitions for the Line Status Register
- */
-#define UART_LSR_TEMT	0x40	/* Transmitter empty */
-#define UART_LSR_THRE	0x20	/* Transmit-hold-register empty */
-#define UART_LSR_BI	0x10	/* Break interrupt indicator */
-#define UART_LSR_FE	0x08	/* Frame error indicator */
-#define UART_LSR_PE	0x04	/* Parity error indicator */
-#define UART_LSR_OE	0x02	/* Overrun error indicator */
-#define UART_LSR_DR	0x01	/* Receiver data ready */
-
-/*
- * These are the definitions for the Interrupt Identification Register
- */
-#define UART_IIR_NO_INT	0x01	/* No interrupts pending */
-#define UART_IIR_ID	0x06	/* Mask for the interrupt ID */
-#define UART_IIR_MSI	0x00	/* Modem status interrupt */
-#define UART_IIR_THRI	0x02	/* Transmitter holding register empty */
-#define UART_IIR_RDI	0x04	/* Receiver data interrupt */
-#define UART_IIR_RLSI	0x06	/* Receiver line status interrupt */
-
-/*
- * These are the definitions for the Interrupt Enable Register
- */
-#define UART_IER_MSI	0x08	/* Enable Modem status interrupt */
-#define UART_IER_RLSI	0x04	/* Enable receiver line status interrupt */
-#define UART_IER_THRI	0x02	/* Enable Transmitter holding register int. */
-#define UART_IER_RDI	0x01	/* Enable receiver data interrupt */
-
-/*
- * These are the definitions for the Modem Control Register
- */
-#define UART_MCR_LOOP	0x10	/* Enable loopback test mode */
-#define UART_MCR_OUT2	0x08	/* Out2 complement */
-#define UART_MCR_OUT1	0x04	/* Out1 complement */
-#define UART_MCR_RTS	0x02	/* RTS complement */
-#define UART_MCR_DTR	0x01	/* DTR complement */
-
-/*
- * These are the definitions for the Modem Status Register
- */
-#define UART_MSR_DCD	0x80	/* Data Carrier Detect */
-#define UART_MSR_RI	0x40	/* Ring Indicator */
-#define UART_MSR_DSR	0x20	/* Data Set Ready */
-#define UART_MSR_CTS	0x10	/* Clear to Send */
-#define UART_MSR_DDCD	0x08	/* Delta DCD */
-#define UART_MSR_TERI	0x04	/* Trailing edge ring indicator */
-#define UART_MSR_DDSR	0x02	/* Delta DSR */
-#define UART_MSR_DCTS	0x01	/* Delta CTS */
-#define UART_MSR_ANY_DELTA 0x0F	/* Any of the delta bits! */
-
-
-/* SSIO */
-#define SSI0_STATUS                0xB1600000
-#define SSI_STATUS_BF              (1<<4)
-#define SSI_STATUS_OF              (1<<3)
-#define SSI_STATUS_UF              (1<<2)
-#define SSI_STATUS_D               (1<<1)
-#define SSI_STATUS_B               (1<<0)
-#define SSI0_INT                   0xB1600004
-#define SSI_INT_OI                 (1<<3)
-#define SSI_INT_UI                 (1<<2)
-#define SSI_INT_DI                 (1<<1)
-#define SSI0_INT_ENABLE            0xB1600008
-#define SSI_INTE_OIE               (1<<3)
-#define SSI_INTE_UIE               (1<<2)
-#define SSI_INTE_DIE               (1<<1)
-#define SSI0_CONFIG                0xB1600020
-#define SSI_CONFIG_AO              (1<<24)
-#define SSI_CONFIG_DO              (1<<23)
-#define SSI_CONFIG_ALEN_BIT        20
-#define SSI_CONFIG_ALEN_MASK       (0x7<<20)
-#define SSI_CONFIG_DLEN_BIT        16
-#define SSI_CONFIG_DLEN_MASK       (0x7<<16)
-#define SSI_CONFIG_DD              (1<<11)
-#define SSI_CONFIG_AD              (1<<10)
-#define SSI_CONFIG_BM_BIT          8
-#define SSI_CONFIG_BM_MASK         (0x3<<8)
-#define SSI_CONFIG_CE              (1<<7)
-#define SSI_CONFIG_DP              (1<<6)
-#define SSI_CONFIG_DL              (1<<5)
-#define SSI_CONFIG_EP              (1<<4)
-#define SSI0_ADATA                 0xB1600024
-#define SSI_AD_D                   (1<<24)
-#define SSI_AD_ADDR_BIT            16
-#define SSI_AD_ADDR_MASK           (0xff<<16)
-#define SSI_AD_DATA_BIT            0
-#define SSI_AD_DATA_MASK           (0xfff<<0)
-#define SSI0_CLKDIV                0xB1600028
-#define SSI0_CONTROL               0xB1600100
-#define SSI_CONTROL_CD             (1<<1)
-#define SSI_CONTROL_E              (1<<0)
-
-/* SSI1 */
-#define SSI1_STATUS                0xB1680000
-#define SSI1_INT                   0xB1680004
-#define SSI1_INT_ENABLE            0xB1680008
-#define SSI1_CONFIG                0xB1680020
-#define SSI1_ADATA                 0xB1680024
-#define SSI1_CLKDIV                0xB1680028
-#define SSI1_ENABLE                0xB1680100
-
-/*
- * Register content definitions
- */
-#define SSI_STATUS_BF				(1<<4)
-#define SSI_STATUS_OF				(1<<3)
-#define SSI_STATUS_UF				(1<<2)
-#define SSI_STATUS_D				(1<<1)
-#define SSI_STATUS_B				(1<<0)
-
-/* SSI_INT */
-#define SSI_INT_OI					(1<<3)
-#define SSI_INT_UI					(1<<2)
-#define SSI_INT_DI					(1<<1)
-
-/* SSI_INTEN */
-#define SSI_INTEN_OIE				(1<<3)
-#define SSI_INTEN_UIE				(1<<2)
-#define SSI_INTEN_DIE				(1<<1)
-
-#define SSI_CONFIG_AO				(1<<24)
-#define SSI_CONFIG_DO				(1<<23)
-#define SSI_CONFIG_ALEN				(7<<20)
-#define SSI_CONFIG_DLEN				(15<<16)
-#define SSI_CONFIG_DD				(1<<11)
-#define SSI_CONFIG_AD				(1<<10)
-#define SSI_CONFIG_BM				(3<<8)
-#define SSI_CONFIG_CE				(1<<7)
-#define SSI_CONFIG_DP				(1<<6)
-#define SSI_CONFIG_DL				(1<<5)
-#define SSI_CONFIG_EP				(1<<4)
-#define SSI_CONFIG_ALEN_N(N)		((N-1)<<20)
-#define SSI_CONFIG_DLEN_N(N)		((N-1)<<16)
-#define SSI_CONFIG_BM_HI			(0<<8)
-#define SSI_CONFIG_BM_LO			(1<<8)
-#define SSI_CONFIG_BM_CY			(2<<8)
-
-#define SSI_ADATA_D					(1<<24)
-#define SSI_ADATA_ADDR				(0xFF<<16)
-#define SSI_ADATA_DATA				(0x0FFF)
-#define SSI_ADATA_ADDR_N(N)			(N<<16)
-
-#define SSI_ENABLE_CD				(1<<1)
-#define SSI_ENABLE_E				(1<<0)
-
-
-/* IrDA Controller */
-#define IRDA_BASE                 0xB0300000
-#define IR_RING_PTR_STATUS        (IRDA_BASE+0x00)
-#define IR_RING_BASE_ADDR_H       (IRDA_BASE+0x04)
-#define IR_RING_BASE_ADDR_L       (IRDA_BASE+0x08)
-#define IR_RING_SIZE              (IRDA_BASE+0x0C)
-#define IR_RING_PROMPT            (IRDA_BASE+0x10)
-#define IR_RING_ADDR_CMPR         (IRDA_BASE+0x14)
-#define IR_INT_CLEAR              (IRDA_BASE+0x18)
-#define IR_CONFIG_1               (IRDA_BASE+0x20)
-#define IR_RX_INVERT_LED        (1<<0)
-#define IR_TX_INVERT_LED        (1<<1)
-#define IR_ST                   (1<<2)
-#define IR_SF                   (1<<3)
-#define IR_SIR                  (1<<4)
-#define IR_MIR                  (1<<5)
-#define IR_FIR                  (1<<6)
-#define IR_16CRC                (1<<7)
-#define IR_TD                   (1<<8)
-#define IR_RX_ALL               (1<<9)
-#define IR_DMA_ENABLE           (1<<10)
-#define IR_RX_ENABLE            (1<<11)
-#define IR_TX_ENABLE            (1<<12)
-#define IR_LOOPBACK             (1<<14)
-#define IR_SIR_MODE	          (IR_SIR | IR_DMA_ENABLE | \
-				   IR_RX_ALL | IR_RX_ENABLE | IR_SF | IR_16CRC)
-#define IR_SIR_FLAGS              (IRDA_BASE+0x24)
-#define IR_ENABLE                 (IRDA_BASE+0x28)
-#define IR_RX_STATUS            (1<<9)
-#define IR_TX_STATUS            (1<<10)
-#define IR_READ_PHY_CONFIG        (IRDA_BASE+0x2C)
-#define IR_WRITE_PHY_CONFIG       (IRDA_BASE+0x30)
-#define IR_MAX_PKT_LEN            (IRDA_BASE+0x34)
-#define IR_RX_BYTE_CNT            (IRDA_BASE+0x38)
-#define IR_CONFIG_2               (IRDA_BASE+0x3C)
-#define IR_MODE_INV             (1<<0)
-#define IR_ONE_PIN              (1<<1)
-#define IR_INTERFACE_CONFIG       (IRDA_BASE+0x40)
-
-/* GPIO */
-#define SYS_PINFUNC               0xB190002C
-#define SYS_PF_USB			(1<<15)	/* 2nd USB device/host */
-#define SYS_PF_U3			(1<<14)	/* GPIO23/U3TXD */
-#define SYS_PF_U2			(1<<13) /* GPIO22/U2TXD */
-#define SYS_PF_U1			(1<<12) /* GPIO21/U1TXD */
-#define SYS_PF_SRC			(1<<11)	/* GPIO6/SROMCKE */
-#define SYS_PF_CK5			(1<<10)	/* GPIO3/CLK5 */
-#define SYS_PF_CK4			(1<<9)	/* GPIO2/CLK4 */
-#define SYS_PF_IRF			(1<<8)	/* GPIO15/IRFIRSEL */
-#define SYS_PF_UR3			(1<<7)	/* GPIO[14:9]/UART3 */
-#define SYS_PF_I2D			(1<<6)	/* GPIO8/I2SDI */
-#define SYS_PF_I2S			(1<<5)	/* I2S/GPIO[29:31] */
-#define SYS_PF_NI2			(1<<4)	/* NI2/GPIO[24:28] */
-#define SYS_PF_U0			(1<<3)	/* U0TXD/GPIO20 */
-#define SYS_PF_RD			(1<<2)	/* IRTXD/GPIO19 */
-#define SYS_PF_A97			(1<<1)	/* AC97/SSL1 */
-#define SYS_PF_S0			(1<<0)	/* SSI_0/GPIO[16:18] */
-#define SYS_TRIOUTRD              0xB1900100
-#define SYS_TRIOUTCLR             0xB1900100
-#define SYS_OUTPUTRD              0xB1900108
-#define SYS_OUTPUTSET             0xB1900108
-#define SYS_OUTPUTCLR             0xB190010C
-#define SYS_PINSTATERD            0xB1900110
-#define SYS_PININPUTEN            0xB1900110
-
-/* GPIO2, Au1500 only */
-#define GPIO2_BASE                0xB1700000
-#define GPIO2_DIR                 (GPIO2_BASE + 0)
-#define GPIO2_DATA_EN             (GPIO2_BASE + 8)
-#define GPIO2_PIN_STATE           (GPIO2_BASE + 0xC)
-#define GPIO2_INT_ENABLE          (GPIO2_BASE + 0x10)
-#define GPIO2_ENABLE              (GPIO2_BASE + 0x14)
-
-/* Power Management */
-#define SYS_SCRATCH0              0xB1900018
-#define SYS_SCRATCH1              0xB190001C
-#define SYS_WAKEMSK               0xB1900034
-#define SYS_ENDIAN                0xB1900038
-#define SYS_POWERCTRL             0xB190003C
-#define SYS_WAKESRC               0xB190005C
-#define SYS_SLPPWR                0xB1900078
-#define SYS_SLEEP                 0xB190007C
-
-/* Clock Controller */
-#define SYS_FREQCTRL0             0xB1900020
-#define SYS_FC_FRDIV2_BIT         22
-#define SYS_FC_FRDIV2_MASK        (0xff << FQC2_FRDIV2_BIT)
-#define SYS_FC_FE2                (1<<21)
-#define SYS_FC_FS2                (1<<20)
-#define SYS_FC_FRDIV1_BIT         12
-#define SYS_FC_FRDIV1_MASK        (0xff << FQC2_FRDIV1_BIT)
-#define SYS_FC_FE1                (1<<11)
-#define SYS_FC_FS1                (1<<10)
-#define SYS_FC_FRDIV0_BIT         2
-#define SYS_FC_FRDIV0_MASK        (0xff << FQC2_FRDIV0_BIT)
-#define SYS_FC_FE0                (1<<1)
-#define SYS_FC_FS0                (1<<0)
-#define SYS_FREQCTRL1             0xB1900024
-#define SYS_FC_FRDIV5_BIT         22
-#define SYS_FC_FRDIV5_MASK        (0xff << FQC2_FRDIV5_BIT)
-#define SYS_FC_FE5                (1<<21)
-#define SYS_FC_FS5                (1<<20)
-#define SYS_FC_FRDIV4_BIT         12
-#define SYS_FC_FRDIV4_MASK        (0xff << FQC2_FRDIV4_BIT)
-#define SYS_FC_FE4                (1<<11)
-#define SYS_FC_FS4                (1<<10)
-#define SYS_FC_FRDIV3_BIT         2
-#define SYS_FC_FRDIV3_MASK        (0xff << FQC2_FRDIV3_BIT)
-#define SYS_FC_FE3                (1<<1)
-#define SYS_FC_FS3                (1<<0)
-#define SYS_CLKSRC                0xB1900028
-#define SYS_CS_ME1_BIT            27
-#define SYS_CS_ME1_MASK           (0x7<<CSC_ME1_BIT)
-#define SYS_CS_DE1                (1<<26)
-#define SYS_CS_CE1                (1<<25)
-#define SYS_CS_ME0_BIT            22
-#define SYS_CS_ME0_MASK           (0x7<<CSC_ME0_BIT)
-#define SYS_CS_DE0                (1<<21)
-#define SYS_CS_CE0                (1<<20)
-#define SYS_CS_MI2_BIT            17
-#define SYS_CS_MI2_MASK           (0x7<<CSC_MI2_BIT)
-#define SYS_CS_DI2                (1<<16)
-#define SYS_CS_CI2                (1<<15)
-#define SYS_CS_MUH_BIT            12
-#define SYS_CS_MUH_MASK           (0x7<<CSC_MUH_BIT)
-#define SYS_CS_DUH                (1<<11)
-#define SYS_CS_CUH                (1<<10)
-#define SYS_CS_MUD_BIT            7
-#define SYS_CS_MUD_MASK           (0x7<<CSC_MUD_BIT)
-#define SYS_CS_DUD                (1<<6)
-#define SYS_CS_CUD                (1<<5)
-#define SYS_CS_MIR_BIT            2
-#define SYS_CS_MIR_MASK           (0x7<<CSC_MIR_BIT)
-#define SYS_CS_DIR                (1<<1)
-#define SYS_CS_CIR                (1<<0)
-
-#define SYS_CS_MUX_AUX            0x1
-#define SYS_CS_MUX_FQ0            0x2
-#define SYS_CS_MUX_FQ1            0x3
-#define SYS_CS_MUX_FQ2            0x4
-#define SYS_CS_MUX_FQ3            0x5
-#define SYS_CS_MUX_FQ4            0x6
-#define SYS_CS_MUX_FQ5            0x7
-#define SYS_CPUPLL                0xB1900060
-#define SYS_AUXPLL                0xB1900064
-
-/* AC97 Controller */
-#define AC97C_CONFIG              0xB0000000
-#define AC97C_RECV_SLOTS_BIT  13
-#define AC97C_RECV_SLOTS_MASK (0x3ff << AC97C_RECV_SLOTS_BIT)
-#define AC97C_XMIT_SLOTS_BIT  3
-#define AC97C_XMIT_SLOTS_MASK (0x3ff << AC97C_XMIT_SLOTS_BIT)
-#define AC97C_SG              (1<<2)
-#define AC97C_SYNC            (1<<1)
-#define AC97C_RESET           (1<<0)
-#define AC97C_STATUS              0xB0000004
-#define AC97C_XU              (1<<11)
-#define AC97C_XO              (1<<10)
-#define AC97C_RU              (1<<9)
-#define AC97C_RO              (1<<8)
-#define AC97C_READY           (1<<7)
-#define AC97C_CP              (1<<6)
-#define AC97C_TR              (1<<5)
-#define AC97C_TE              (1<<4)
-#define AC97C_TF              (1<<3)
-#define AC97C_RR              (1<<2)
-#define AC97C_RE              (1<<1)
-#define AC97C_RF              (1<<0)
-#define AC97C_DATA                0xB0000008
-#define AC97C_CMD                 0xB000000C
-#define AC97C_WD_BIT          16
-#define AC97C_READ            (1<<7)
-#define AC97C_INDEX_MASK      0x7f
-#define AC97C_CNTRL               0xB0000010
-#define AC97C_RS              (1<<1)
-#define AC97C_CE              (1<<0)
-
-#define DB1000_BCSR_ADDR 0xAE000000
-#define DB1550_BCSR_ADDR 0xAF000000
-
-#define DB1XX0_BCSR_ADDR DB1000_BCSR_ADDR
-
-#ifdef CONFIG_SOC_AU1500
-/* Au1500 PCI Controller */
-#define Au1500_CFG_BASE           0xB4005000 /* virtual, kseg0 addr */
-#define Au1500_PCI_CMEM           (Au1500_CFG_BASE + 0)
-#define Au1500_PCI_CFG            (Au1500_CFG_BASE + 4)
-#define PCI_ERROR ((1<<22) | (1<<23) | (1<<24) | (1<<25) | (1<<26) | (1<<27))
-#define Au1500_PCI_B2BMASK_CCH    (Au1500_CFG_BASE + 8)
-#define Au1500_PCI_B2B0_VID       (Au1500_CFG_BASE + 0xC)
-#define Au1500_PCI_B2B1_ID        (Au1500_CFG_BASE + 0x10)
-#define Au1500_PCI_MWMASK_DEV     (Au1500_CFG_BASE + 0x14)
-#define Au1500_PCI_MWBASE_REV_CCL (Au1500_CFG_BASE + 0x18)
-#define Au1500_PCI_ERR_ADDR       (Au1500_CFG_BASE + 0x1C)
-#define Au1500_PCI_SPEC_INTACK    (Au1500_CFG_BASE + 0x20)
-#define Au1500_PCI_ID             (Au1500_CFG_BASE + 0x100)
-#define Au1500_PCI_STATCMD        (Au1500_CFG_BASE + 0x104)
-#define Au1500_PCI_CLASSREV       (Au1500_CFG_BASE + 0x108)
-#define Au1500_PCI_HDRTYPE        (Au1500_CFG_BASE + 0x10C)
-#define Au1500_PCI_MBAR           (Au1500_CFG_BASE + 0x110)
-
-#define Au1500_PCI_HDR            0xB4005100 /* virtual, kseg0 addr */
-
-/* All of our structures, like pci resource, have 32 bit members.
- * Drivers are expected to do an ioremap on the PCI MEM resource, but it's
- * hard to store 0x4 0000 0000 in a 32 bit type.  We require a small patch
- * to __ioremap to check for addresses between (u32)Au1500_PCI_MEM_START and
- * (u32)Au1500_PCI_MEM_END and change those to the full 36 bit PCI MEM
- * addresses.  For PCI IO, it's simpler because we get to do the ioremap
- * ourselves and then adjust the device's resources.
- */
-#define Au1500_EXT_CFG            0x600000000
-#define Au1500_EXT_CFG_TYPE1      0x680000000
-#define Au1500_PCI_IO_START       0x500000000
-#define Au1500_PCI_IO_END         0x5000FFFFF
-#define Au1500_PCI_MEM_START      0x440000000
-#define Au1500_PCI_MEM_END        0x443FFFFFF
-
-#define PCI_IO_START    (Au1500_PCI_IO_START + 0x300)
-#define PCI_IO_END      (Au1500_PCI_IO_END)
-#define PCI_MEM_START   (Au1500_PCI_MEM_START)
-#define PCI_MEM_END     (Au1500_PCI_MEM_END)
-#define PCI_FIRST_DEVFN (0<<3)
-#define PCI_LAST_DEVFN  (19<<3)
-
-#endif
-
-#if defined(CONFIG_SOC_AU1100) || (defined(CONFIG_SOC_AU1000) && !defined(CONFIG_MIPS_PB1000))
-/* no PCI bus controller */
-#define PCI_IO_START    0
-#define PCI_IO_END      0
-#define PCI_MEM_START   0
-#define PCI_MEM_END     0
-#define PCI_FIRST_DEVFN 0
-#define PCI_LAST_DEVFN  0
-#endif
-#define AU1X_SOCK0_IO        0xF00000000
-#define AU1X_SOCK0_PHYS_ATTR 0xF40000000
-#define AU1X_SOCK0_PHYS_MEM  0xF80000000
-
-/* pcmcia socket 1 needs external glue logic so the memory map
- * differs from board to board.
- */
-
-/* Only for db board, not older pb */
-#define AU1X_SOCK1_IO        0xF04000000
-#define AU1X_SOCK1_PHYS_ATTR 0xF44000000
-#define AU1X_SOCK1_PHYS_MEM  0xF84000000
-
-#endif