dm: dts: Convert driver model tags to use new schema
Now that Linux has accepted these tags, move the device tree files in
U-Boot over to use them.
Signed-off-by: Simon Glass <sjg@chromium.org>
diff --git a/arch/arm/dts/k3-j721s2-r5-common-proc-board.dts b/arch/arm/dts/k3-j721s2-r5-common-proc-board.dts
index 9e3bdec..bc61702 100644
--- a/arch/arm/dts/k3-j721s2-r5-common-proc-board.dts
+++ b/arch/arm/dts/k3-j721s2-r5-common-proc-board.dts
@@ -23,7 +23,7 @@
fs_loader0: fs_loader@0 {
compatible = "u-boot,fs-loader";
- u-boot,dm-pre-reloc;
+ bootph-all;
};
a72_0: a72@0 {
@@ -39,27 +39,27 @@
ti,sci = <&sms>;
ti,sci-proc-id = <32>;
ti,sci-host-id = <10>;
- u-boot,dm-spl;
+ bootph-pre-ram;
};
clk_200mhz: dummy_clock_200mhz {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <200000000>;
- u-boot,dm-spl;
+ bootph-pre-ram;
};
clk_19_2mhz: dummy_clock_19_2mhz {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <19200000>;
- u-boot,dm-spl;
+ bootph-pre-ram;
};
};
&cbass_mcu_wakeup {
sa3_secproxy: secproxy@44880000 {
- u-boot,dm-spl;
+ bootph-pre-ram;
compatible = "ti,am654-secure-proxy";
reg = <0x0 0x44880000 0x0 0x20000>,
<0x0 0x44860000 0x0 0x20000>,
@@ -75,14 +75,14 @@
<0x0 0x2a480000 0x0 0x80000>;
reg-names = "rt", "scfg", "target_data";
#mbox-cells = <1>;
- u-boot,dm-spl;
+ bootph-pre-ram;
};
sysctrler: sysctrler {
compatible = "ti,am654-system-controller";
mboxes= <&mcu_secproxy 4>, <&mcu_secproxy 5>, <&sa3_secproxy 5>;
mbox-names = "tx", "rx", "boot_notify";
- u-boot,dm-spl;
+ bootph-pre-ram;
};
dm_tifs: dm-tifs {
@@ -92,7 +92,7 @@
mbox-names = "rx", "tx";
mboxes= <&mcu_secproxy 21>,
<&mcu_secproxy 23>;
- u-boot,dm-spl;
+ bootph-pre-ram;
};
};
@@ -122,7 +122,7 @@
&wkup_pmx0 {
mcu_uart0_pins_default: mcu-uart0-pins-default {
- u-boot,dm-spl;
+ bootph-pre-ram;
pinctrl-single,pins = <
J721S2_WKUP_IOPAD(0x0f8, PIN_INPUT, 0) /* (B24) WKUP_GPIO0_14.MCU_UART0_CTSn */
J721S2_WKUP_IOPAD(0x0fc, PIN_OUTPUT, 0) /* (D25) WKUP_GPIO0_15.MCU_UART0_RTSn */
@@ -132,7 +132,7 @@
};
wkup_uart0_pins_default: wkup-uart0-pins-default {
- u-boot,dm-spl;
+ bootph-pre-ram;
pinctrl-single,pins = <
J721S2_WKUP_IOPAD(0x0d8, PIN_INPUT, 0) /* (E25) WKUP_GPIO0_6.WKUP_UART0_CTSn */
J721S2_WKUP_IOPAD(0x0dc, PIN_OUTPUT, 0) /* (F28) WKUP_GPIO0_7.WKUP_UART0_RTSn */
@@ -147,7 +147,7 @@
mbox-names = "tx", "rx", "notify";
ti,host-id = <4>;
ti,secure-host;
- u-boot,dm-spl;
+ bootph-pre-ram;
};
&wkup_uart0 {