sunxi: h616: add Tanix TX1 support
The Tanix TX1 is a tiny TV box, featuring the Allwinner H313 SoC with up
to 2GB of DRAM and 16GB of eMMC. There is no SD card or Ethernet port on
this small device, but it can be booted via the USB debug "FEL" mode.
The bootloader could then be written to the eMMC.
Add the defconfig for that board, and add the devicetree file to the
Makefile, for it to be built.
The DRAM parameters were taken from the vendor firmware on the eMMC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 82d37ad..871cfbb 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -678,6 +678,7 @@
sun50i-h6-tanix-tx6.dtb \
sun50i-h6-tanix-tx6-mini.dtb
dtb-$(CONFIG_MACH_SUN50I_H616) += \
+ sun50i-h313-tanix-tx1.dtb \
sun50i-h616-orangepi-zero2.dtb \
sun50i-h618-orangepi-zero2w.dtb \
sun50i-h618-orangepi-zero3.dtb \
diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
index 4bcd9b9..4ad77c7 100644
--- a/board/sunxi/MAINTAINERS
+++ b/board/sunxi/MAINTAINERS
@@ -549,6 +549,12 @@
F: configs/Sunchip_CX-A99_defconfig
W: https://linux-sunxi.org/Sunchip_CX-A99
+TANIX TX1 BOARD
+M: Andre Przywara <andre.przywara@arm.com>
+S: Maintained
+F: configs/tanix_tx1_defconfig
+W: https://linux-sunxi.org/Tanix_TX1
+
TANIX TX6 BOARD
M: Jernej Skrabec <jernej.skrabec@siol.net>
S: Maintained
diff --git a/configs/tanix_tx1_defconfig b/configs/tanix_tx1_defconfig
new file mode 100644
index 0000000..9915fff
--- /dev/null
+++ b/configs/tanix_tx1_defconfig
@@ -0,0 +1,25 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_DEFAULT_DEVICE_TREE="sun50i-h313-tanix-tx1"
+CONFIG_SPL=y
+CONFIG_DRAM_SUN50I_H616_DX_ODT=0x06060606
+CONFIG_DRAM_SUN50I_H616_DX_DRI=0x0d0d0d0d
+CONFIG_DRAM_SUN50I_H616_CA_DRI=0x1919
+CONFIG_DRAM_SUN50I_H616_ODT_EN=0x9988eeee
+CONFIG_DRAM_SUN50I_H616_TPR6=0x2fb08080
+CONFIG_DRAM_SUN50I_H616_TPR10=0x402f4469
+CONFIG_DRAM_SUN50I_H616_TPR11=0x0e0f0d0d
+CONFIG_DRAM_SUN50I_H616_TPR12=0x11131213
+CONFIG_MACH_SUN50I_H616=y
+CONFIG_SUNXI_DRAM_H616_LPDDR3=y
+CONFIG_R_I2C_ENABLE=y
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL_I2C=y
+CONFIG_SPL_SYS_I2C_LEGACY=y
+CONFIG_SYS_I2C_MVTWSI=y
+CONFIG_SYS_I2C_SLAVE=0x7f
+CONFIG_SYS_I2C_SPEED=400000
+CONFIG_AXP313_POWER=y
+CONFIG_AXP_DCDC3_VOLT=1200
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y