siemens,am33x: add draco etamin board
In the draco CPU board family, etamin is a new variant
with bigger flash and more RAM. Due to new flash that
uses larger pages (4K) some changes are necessary because
it impacts the MTD partition layout and the ubi mount
parameters.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
[trini: Move BOOTDELAY into defconfig, just always be 3 now]
Signed-off-by: Tom Rini <trini@konsulko.com>
diff --git a/board/siemens/draco/board.c b/board/siemens/draco/board.c
index 41bdef0..d8869a0 100644
--- a/board/siemens/draco/board.c
+++ b/board/siemens/draco/board.c
@@ -24,6 +24,7 @@
#include <asm/arch/gpio.h>
#include <asm/arch/mmc_host_def.h>
#include <asm/arch/sys_proto.h>
+#include <asm/arch/mem.h>
#include <asm/io.h>
#include <asm/emif.h>
#include <asm/gpio.h>
@@ -33,6 +34,7 @@
#include <watchdog.h>
#include "board.h"
#include "../common/factoryset.h"
+#include <nand.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -40,6 +42,7 @@
static struct draco_baseboard_id __attribute__((section(".data"))) settings;
#if DDR_PLL_FREQ == 303
+#if !defined(CONFIG_TARGET_ETAMIN)
/* Default@303MHz-i0 */
const struct ddr3_data ddr3_default = {
0x33524444, 0x56312e35, 0x0080, 0x0000, 0x003A, 0x003F, 0x009F,
@@ -48,6 +51,16 @@
"default name @303MHz \0",
"default marking \0",
};
+#else
+/* etamin board */
+const struct ddr3_data ddr3_default = {
+ 0x33524444, 0x56312e36, 0x0080, 0x0000, 0x003A, 0x0010, 0x009F,
+ 0x0050, 0x0888A39B, 0x266D7FDA, 0x501F86AF, 0x00100206, 0x61A44BB2,
+ 0x0000093B, 0x0000018A,
+ "test-etamin \0",
+ "generic-8Gbit \0",
+};
+#endif
#elif DDR_PLL_FREQ == 400
/* Default@400MHz-i0 */
const struct ddr3_data ddr3_default = {
@@ -210,6 +223,7 @@
draco_ddr3_emif_reg_data.emif_ddr_phy_ctlr_1 =
settings.ddr3.emif_ddr_phy_ctlr_1;
draco_ddr3_emif_reg_data.sdram_config = settings.ddr3.sdram_config;
+ draco_ddr3_emif_reg_data.sdram_config2 = 0x08000000;
draco_ddr3_emif_reg_data.ref_ctrl = settings.ddr3.ref_ctrl;
draco_ddr3_data.datardsratio0 = settings.ddr3.dt0rdsratio0;
@@ -251,6 +265,10 @@
nand_curr_device = 0;
omap_nand_switch_ecc(1, ecc_type);
+#ifdef CONFIG_TARGET_ETAMIN
+ nand_curr_device = 1;
+ omap_nand_switch_ecc(1, ecc_type);
+#endif
#ifdef CONFIG_FACTORYSET
/* Set ASN in environment*/
if (factory_dat.asn[0] != 0) {
@@ -326,7 +344,7 @@
}
static int do_switch_reset(cmd_tbl_t *cmdtp, int flag, int argc,
- char *const argv[])
+ char *const argv[])
{
/* Reset SMSC LAN9303 switch for default configuration */
gpio_request(GPIO_LAN9303_NRST, "nRST");
@@ -346,4 +364,23 @@
#endif /* #if defined(CONFIG_DRIVER_TI_CPSW) */
#endif /* #if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) */
+#ifdef CONFIG_NAND_CS_INIT
+/* GPMC definitions for second nand cs1 */
+static const u32 gpmc_nand_config[] = {
+ ETAMIN_NAND_GPMC_CONFIG1,
+ ETAMIN_NAND_GPMC_CONFIG2,
+ ETAMIN_NAND_GPMC_CONFIG3,
+ ETAMIN_NAND_GPMC_CONFIG4,
+ ETAMIN_NAND_GPMC_CONFIG5,
+ ETAMIN_NAND_GPMC_CONFIG6,
+ /*CONFIG7- computed as params */
+};
+
+static void board_nand_cs_init(void)
+{
+ enable_gpmc_cs_config(gpmc_nand_config, &gpmc_cfg->cs[1],
+ 0x18000000, GPMC_SIZE_16M);
+}
+#endif
+
#include "../common/board.c"