Merge branch 'master' of git://git.denx.de/u-boot-socfpga
- Update SPDX tag in arch/arm/mach-socfpga/spl_a10.c
Signed-off-by: Tom Rini <trini@konsulko.com>
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 4fbb424..5b3746c 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -759,10 +759,10 @@
bool "Altera SOCFPGA family"
select ARCH_EARLY_INIT_R
select ARCH_MISC_INIT
- select CPU_V7A
+ select CPU_V7A if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
select DM
select DM_SERIAL
- select ENABLE_ARM_SOC_BOOT0_HOOK
+ select ENABLE_ARM_SOC_BOOT0_HOOK if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
select OF_CONTROL
select SPL_LIBCOMMON_SUPPORT
select SPL_LIBDISK_SUPPORT
@@ -772,20 +772,22 @@
select SPL_OF_CONTROL
select SPL_SERIAL_SUPPORT
select SPL_DM_SERIAL
+ select SPL_RESET_SUPPORT
select SPL_SPI_FLASH_SUPPORT if SPL_SPI_SUPPORT
select SPL_SPI_SUPPORT if DM_SPI
select SPL_WATCHDOG_SUPPORT
select SUPPORT_SPL
select SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION_TYPE
select SYS_NS16550
- select SYS_THUMB_BUILD
+ select SYS_THUMB_BUILD if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
+ select ARM64 if TARGET_SOCFPGA_STRATIX10
imply CMD_MTDPARTS
imply CRC32_VERIFY
imply DM_SPI
imply DM_SPI_FLASH
imply FAT_WRITE
- imply HW_WATCHDOG
imply SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
+ select SPL_SEPARATE_BSS if TARGET_SOCFPGA_STRATIX10
config ARCH_SUNXI
bool "Support sunxi (Allwinner) SoCs"
diff --git a/arch/arm/dts/socfpga_arria10_socdk.dtsi b/arch/arm/dts/socfpga_arria10_socdk.dtsi
index d7616dd..3f59f02 100644
--- a/arch/arm/dts/socfpga_arria10_socdk.dtsi
+++ b/arch/arm/dts/socfpga_arria10_socdk.dtsi
@@ -34,6 +34,7 @@
name = "memory";
device_type = "memory";
reg = <0x0 0x40000000>; /* 1GB */
+ u-boot,dm-pre-reloc;
};
a10leds {
diff --git a/arch/arm/dts/socfpga_stratix10_socdk.dts b/arch/arm/dts/socfpga_stratix10_socdk.dts
index c6ab0ae..6e8ddcd 100644
--- a/arch/arm/dts/socfpga_stratix10_socdk.dts
+++ b/arch/arm/dts/socfpga_stratix10_socdk.dts
@@ -36,8 +36,8 @@
memory {
device_type = "memory";
- /* We expect the bootloader to fill in the reg */
- reg = <0 0 0 0>;
+ reg = <0 0 0 0x80000000>; /* 2GB */
+ u-boot,dm-pre-reloc;
};
};
diff --git a/arch/arm/mach-socfpga/Kconfig b/arch/arm/mach-socfpga/Kconfig
index 30b4752..91ea742 100644
--- a/arch/arm/mach-socfpga/Kconfig
+++ b/arch/arm/mach-socfpga/Kconfig
@@ -20,6 +20,12 @@
bool
select ALTERA_SDRAM
+config TARGET_SOCFPGA_STRATIX10
+ bool
+ select ARMV8_MULTIENTRY
+ select ARMV8_SPIN_TABLE
+ select ARMV8_SET_SMPEN
+
choice
prompt "Altera SOCFPGA board select"
optional
@@ -57,6 +63,10 @@
bool "SR1500 (Cyclone V)"
select TARGET_SOCFPGA_CYCLONE5
+config TARGET_SOCFPGA_STRATIX10_SOCDK
+ bool "Intel SOCFPGA SoCDK (Stratix 10)"
+ select TARGET_SOCFPGA_STRATIX10
+
config TARGET_SOCFPGA_TERASIC_DE0_NANO
bool "Terasic DE0-Nano-Atlas (Cyclone V)"
select TARGET_SOCFPGA_CYCLONE5
@@ -87,12 +97,14 @@
default "sockit" if TARGET_SOCFPGA_TERASIC_SOCKIT
default "socrates" if TARGET_SOCFPGA_EBV_SOCRATES
default "sr1500" if TARGET_SOCFPGA_SR1500
+ default "stratix10-socdk" if TARGET_SOCFPGA_STRATIX10_SOCDK
default "vining_fpga" if TARGET_SOCFPGA_SAMTEC_VINING_FPGA
config SYS_VENDOR
default "altera" if TARGET_SOCFPGA_ARRIA5_SOCDK
default "altera" if TARGET_SOCFPGA_ARRIA10_SOCDK
default "altera" if TARGET_SOCFPGA_CYCLONE5_SOCDK
+ default "altera" if TARGET_SOCFPGA_STRATIX10_SOCDK
default "devboards" if TARGET_SOCFPGA_DEVBOARDS_DBM_SOC1
default "ebv" if TARGET_SOCFPGA_EBV_SOCRATES
default "samtec" if TARGET_SOCFPGA_SAMTEC_VINING_FPGA
@@ -116,6 +128,7 @@
default "socfpga_sockit" if TARGET_SOCFPGA_TERASIC_SOCKIT
default "socfpga_socrates" if TARGET_SOCFPGA_EBV_SOCRATES
default "socfpga_sr1500" if TARGET_SOCFPGA_SR1500
+ default "socfpga_stratix10_socdk" if TARGET_SOCFPGA_STRATIX10_SOCDK
default "socfpga_vining_fpga" if TARGET_SOCFPGA_SAMTEC_VINING_FPGA
endif
diff --git a/arch/arm/mach-socfpga/Makefile b/arch/arm/mach-socfpga/Makefile
index 61f5778..654999c 100644
--- a/arch/arm/mach-socfpga/Makefile
+++ b/arch/arm/mach-socfpga/Makefile
@@ -9,7 +9,6 @@
obj-y += clock_manager.o
obj-y += misc.o
obj-y += reset_manager.o
-obj-y += timer.o
ifdef CONFIG_TARGET_SOCFPGA_GEN5
obj-y += clock_manager_gen5.o
@@ -17,6 +16,7 @@
obj-y += reset_manager_gen5.o
obj-y += scan_manager.o
obj-y += system_manager_gen5.o
+obj-y += timer.o
obj-y += wrap_pll_config.o
obj-y += fpga_manager.o
endif
@@ -26,23 +26,35 @@
obj-y += misc_arria10.o
obj-y += pinmux_arria10.o
obj-y += reset_manager_arria10.o
+obj-y += timer.o
endif
ifdef CONFIG_TARGET_SOCFPGA_STRATIX10
obj-y += clock_manager_s10.o
+obj-y += mailbox_s10.o
+obj-y += misc_s10.o
+obj-y += mmu-arm64_s10.o
obj-y += reset_manager_s10.o
obj-y += system_manager_s10.o
+obj-y += timer_s10.o
obj-y += wrap_pinmux_config_s10.o
obj-y += wrap_pll_config_s10.o
endif
+
ifdef CONFIG_SPL_BUILD
-obj-y += spl.o
ifdef CONFIG_TARGET_SOCFPGA_GEN5
+obj-y += spl_gen5.o
obj-y += freeze_controller.o
obj-y += wrap_iocsr_config.o
obj-y += wrap_pinmux_config.o
obj-y += wrap_sdram_config.o
endif
+ifdef CONFIG_TARGET_SOCFPGA_ARRIA10
+obj-y += spl_a10.o
+endif
+ifdef CONFIG_TARGET_SOCFPGA_STRATIX10
+obj-y += spl_s10.o
+endif
endif
ifdef CONFIG_TARGET_SOCFPGA_GEN5
diff --git a/arch/arm/mach-socfpga/board.c b/arch/arm/mach-socfpga/board.c
index 189e12a..26d84be 100644
--- a/arch/arm/mach-socfpga/board.c
+++ b/arch/arm/mach-socfpga/board.c
@@ -18,7 +18,20 @@
DECLARE_GLOBAL_DATA_PTR;
-void s_init(void) {}
+void s_init(void) {
+#ifndef CONFIG_ARM64
+ /*
+ * Preconfigure ACTLR, make sure Write Full Line of Zeroes is disabled.
+ * This is optional on CycloneV / ArriaV.
+ * This is mandatory on Arria10, otherwise Linux refuses to boot.
+ */
+ asm volatile(
+ "mcr p15, 0, %0, c1, c0, 1\n"
+ "isb\n"
+ "dsb\n"
+ ::"r"(0x0));
+#endif
+}
/*
* Miscellaneous platform dependent initialisations
diff --git a/arch/arm/mach-socfpga/include/mach/firewall_s10.h b/arch/arm/mach-socfpga/include/mach/firewall_s10.h
new file mode 100644
index 0000000..b96f779
--- /dev/null
+++ b/arch/arm/mach-socfpga/include/mach/firewall_s10.h
@@ -0,0 +1,120 @@
+/* SPDX-License-Identifier: GPL-2.0
+ *
+ * Copyright (C) 2017-2018 Intel Corporation <www.intel.com>
+ *
+ */
+
+#ifndef _FIREWALL_S10_
+#define _FIREWALL_S10_
+
+struct socfpga_firwall_l4_per {
+ u32 nand; /* 0x00 */
+ u32 nand_data;
+ u32 _pad_0x8;
+ u32 usb0;
+ u32 usb1; /* 0x10 */
+ u32 _pad_0x14;
+ u32 _pad_0x18;
+ u32 spim0;
+ u32 spim1; /* 0x20 */
+ u32 spis0;
+ u32 spis1;
+ u32 emac0;
+ u32 emac1; /* 0x30 */
+ u32 emac2;
+ u32 _pad_0x38;
+ u32 _pad_0x3c;
+ u32 sdmmc; /* 0x40 */
+ u32 gpio0;
+ u32 gpio1;
+ u32 _pad_0x4c;
+ u32 i2c0; /* 0x50 */
+ u32 i2c1;
+ u32 i2c2;
+ u32 i2c3;
+ u32 i2c4; /* 0x60 */
+ u32 timer0;
+ u32 timer1;
+ u32 uart0;
+ u32 uart1; /* 0x70 */
+};
+
+struct socfpga_firwall_l4_sys {
+ u32 _pad_0x00; /* 0x00 */
+ u32 _pad_0x04;
+ u32 dma_ecc;
+ u32 emac0rx_ecc;
+ u32 emac0tx_ecc; /* 0x10 */
+ u32 emac1rx_ecc;
+ u32 emac1tx_ecc;
+ u32 emac2rx_ecc;
+ u32 emac2tx_ecc; /* 0x20 */
+ u32 _pad_0x24;
+ u32 _pad_0x28;
+ u32 nand_ecc;
+ u32 nand_read_ecc; /* 0x30 */
+ u32 nand_write_ecc;
+ u32 ocram_ecc;
+ u32 _pad_0x3c;
+ u32 sdmmc_ecc; /* 0x40 */
+ u32 usb0_ecc;
+ u32 usb1_ecc;
+ u32 clock_manager;
+ u32 _pad_0x50; /* 0x50 */
+ u32 io_manager;
+ u32 reset_manager;
+ u32 system_manager;
+ u32 osc0_timer; /* 0x60 */
+ u32 osc1_timer;
+ u32 watchdog0;
+ u32 watchdog1;
+ u32 watchdog2; /* 0x70 */
+ u32 watchdog3;
+};
+
+#define FIREWALL_L4_DISABLE_ALL (BIT(0) | BIT(24) | BIT(16))
+#define FIREWALL_BRIDGE_DISABLE_ALL (~0)
+
+/* Cache coherency unit (CCU) registers */
+#define CCU_CPU0_MPRT_ADBASE_DDRREG 0x4400
+#define CCU_CPU0_MPRT_ADBASE_MEMSPACE0 0x45c0
+#define CCU_CPU0_MPRT_ADBASE_MEMSPACE1A 0x45e0
+#define CCU_CPU0_MPRT_ADBASE_MEMSPACE1B 0x4600
+#define CCU_CPU0_MPRT_ADBASE_MEMSPACE1C 0x4620
+#define CCU_CPU0_MPRT_ADBASE_MEMSPACE1D 0x4640
+#define CCU_CPU0_MPRT_ADBASE_MEMSPACE1E 0x4660
+
+#define CCU_CPU0_MPRT_ADMASK_MEM_RAM0 0x4688
+
+#define CCU_IOM_MPRT_ADBASE_MEMSPACE0 0x18560
+#define CCU_IOM_MPRT_ADBASE_MEMSPACE1A 0x18580
+#define CCU_IOM_MPRT_ADBASE_MEMSPACE1B 0x185a0
+#define CCU_IOM_MPRT_ADBASE_MEMSPACE1C 0x185c0
+#define CCU_IOM_MPRT_ADBASE_MEMSPACE1D 0x185e0
+#define CCU_IOM_MPRT_ADBASE_MEMSPACE1E 0x18600
+
+#define CCU_IOM_MPRT_ADMASK_MEM_RAM0 0x18628
+
+#define CCU_ADMASK_P_MASK BIT(0)
+#define CCU_ADMASK_NS_MASK BIT(1)
+
+#define CCU_ADBASE_DI_MASK BIT(4)
+
+#define CCU_REG_ADDR(reg) \
+ (SOCFPGA_CCU_ADDRESS + (reg))
+
+/* Firewall MPU DDR SCR registers */
+#define FW_MPU_DDR_SCR_EN 0x00
+#define FW_MPU_DDR_SCR_EN_SET 0x04
+#define FW_MPU_DDR_SCR_MPUREGION0ADDR_LIMIT 0x18
+#define FW_MPU_DDR_SCR_MPUREGION0ADDR_LIMITEXT 0x1c
+#define FW_MPU_DDR_SCR_NONMPUREGION0ADDR_LIMIT 0x98
+#define FW_MPU_DDR_SCR_NONMPUREGION0ADDR_LIMITEXT 0x9c
+
+#define MPUREGION0_ENABLE BIT(0)
+#define NONMPUREGION0_ENABLE BIT(8)
+
+#define FW_MPU_DDR_SCR_WRITEL(data, reg) \
+ writel(data, SOCFPGA_FW_MPU_DDR_SCR_ADDRESS + (reg))
+
+#endif /* _FIREWALL_S10_ */
diff --git a/arch/arm/mach-socfpga/include/mach/mailbox_s10.h b/arch/arm/mach-socfpga/include/mach/mailbox_s10.h
new file mode 100644
index 0000000..81a609d
--- /dev/null
+++ b/arch/arm/mach-socfpga/include/mach/mailbox_s10.h
@@ -0,0 +1,144 @@
+/* SPDX-License-Identifier: GPL-2.0
+ *
+ * Copyright (C) 2017-2018 Intel Corporation <www.intel.com>
+ *
+ */
+
+#ifndef _MAILBOX_S10_H_
+#define _MAILBOX_S10_H_
+
+/* user define Uboot ID */
+#define MBOX_CLIENT_ID_UBOOT 0xB
+#define MBOX_ID_UBOOT 0x1
+
+#define MBOX_CMD_DIRECT 0
+#define MBOX_CMD_INDIRECT 1
+
+#define MBOX_MAX_CMD_INDEX 2047
+#define MBOX_CMD_BUFFER_SIZE 32
+#define MBOX_RESP_BUFFER_SIZE 16
+
+#define MBOX_HDR_CMD_LSB 0
+#define MBOX_HDR_CMD_MSK (BIT(11) - 1)
+#define MBOX_HDR_I_LSB 11
+#define MBOX_HDR_I_MSK BIT(11)
+#define MBOX_HDR_LEN_LSB 12
+#define MBOX_HDR_LEN_MSK 0x007FF000
+#define MBOX_HDR_ID_LSB 24
+#define MBOX_HDR_ID_MSK 0x0F000000
+#define MBOX_HDR_CLIENT_LSB 28
+#define MBOX_HDR_CLIENT_MSK 0xF0000000
+
+/* Interrupt flags */
+#define MBOX_FLAGS_INT_COE BIT(0) /* COUT update interrupt enable */
+#define MBOX_FLAGS_INT_RIE BIT(1) /* RIN update interrupt enable */
+#define MBOX_FLAGS_INT_UAE BIT(8) /* Urgent ACK interrupt enable */
+#define MBOX_ALL_INTRS (MBOX_FLAGS_INT_COE | \
+ MBOX_FLAGS_INT_RIE | \
+ MBOX_FLAGS_INT_UAE)
+
+/* Status */
+#define MBOX_STATUS_UA_MSK BIT(8)
+
+#define MBOX_CMD_HEADER(client, id, len, indirect, cmd) \
+ ((((cmd) << MBOX_HDR_CMD_LSB) & MBOX_HDR_CMD_MSK) | \
+ (((indirect) << MBOX_HDR_I_LSB) & MBOX_HDR_I_MSK) | \
+ (((len) << MBOX_HDR_LEN_LSB) & MBOX_HDR_LEN_MSK) | \
+ (((id) << MBOX_HDR_ID_LSB) & MBOX_HDR_ID_MSK) | \
+ (((client) << MBOX_HDR_CLIENT_LSB) & MBOX_HDR_CLIENT_MSK))
+
+#define MBOX_RESP_ERR_GET(resp) \
+ (((resp) & MBOX_HDR_CMD_MSK) >> MBOX_HDR_CMD_LSB)
+#define MBOX_RESP_LEN_GET(resp) \
+ (((resp) & MBOX_HDR_LEN_MSK) >> MBOX_HDR_LEN_LSB)
+#define MBOX_RESP_ID_GET(resp) \
+ (((resp) & MBOX_HDR_ID_MSK) >> MBOX_HDR_ID_LSB)
+#define MBOX_RESP_CLIENT_GET(resp) \
+ (((resp) & MBOX_HDR_CLIENT_MSK) >> MBOX_HDR_CLIENT_LSB)
+
+/* Response error list */
+enum ALT_SDM_MBOX_RESP_CODE {
+ /* CMD completed successfully, but check resp ARGS for any errors */
+ MBOX_RESP_STATOK = 0,
+ /* CMD is incorrectly formatted in some way */
+ MBOX_RESP_INVALID_COMMAND = 1,
+ /* BootROM Command code not undesrtood */
+ MBOX_RESP_UNKNOWN_BR = 2,
+ /* CMD code not recognized by firmware */
+ MBOX_RESP_UNKNOWN = 3,
+ /* Indicates that the device is not configured */
+ MBOX_RESP_NOT_CONFIGURED = 256,
+ /* Indicates that the device is busy */
+ MBOX_RESP_DEVICE_BUSY = 0x1FF,
+ /* Indicates that there is no valid response available */
+ MBOX_RESP_NO_VALID_RESP_AVAILABLE = 0x2FF,
+ /* General Error */
+ MBOX_RESP_ERROR = 0x3FF,
+};
+
+/* Mailbox command list */
+#define MBOX_RESTART 2
+#define MBOX_CONFIG_STATUS 4
+#define MBOX_RECONFIG 6
+#define MBOX_RECONFIG_MSEL 7
+#define MBOX_RECONFIG_DATA 8
+#define MBOX_RECONFIG_STATUS 9
+#define MBOX_QSPI_OPEN 50
+#define MBOX_QSPI_CLOSE 51
+#define MBOX_QSPI_DIRECT 59
+#define MBOX_REBOOT_HPS 71
+
+/* Mailbox registers */
+#define MBOX_CIN 0 /* command valid offset */
+#define MBOX_ROUT 4 /* response output offset */
+#define MBOX_URG 8 /* urgent command */
+#define MBOX_FLAGS 0x0c /* interrupt enables */
+#define MBOX_COUT 0x20 /* command free offset */
+#define MBOX_RIN 0x24 /* respond valid offset */
+#define MBOX_STATUS 0x2c /* mailbox status */
+#define MBOX_CMD_BUF 0x40 /* circular command buffer */
+#define MBOX_RESP_BUF 0xc0 /* circular response buffer */
+#define MBOX_DOORBELL_TO_SDM 0x400 /* Doorbell to SDM */
+#define MBOX_DOORBELL_FROM_SDM 0x480 /* Doorbell from SDM */
+
+/* Status and bit information returned by RECONFIG_STATUS */
+#define RECONFIG_STATUS_RESPONSE_LEN 6
+#define RECONFIG_STATUS_STATE 0
+#define RECONFIG_STATUS_PIN_STATUS 2
+#define RECONFIG_STATUS_SOFTFUNC_STATUS 3
+
+#define MBOX_CFGSTAT_STATE_IDLE 0x00000000
+#define MBOX_CFGSTAT_STATE_CONFIG 0x10000000
+#define MBOX_CFGSTAT_STATE_FAILACK 0x08000000
+#define MBOX_CFGSTAT_STATE_ERROR_INVALID 0xf0000001
+#define MBOX_CFGSTAT_STATE_ERROR_CORRUPT 0xf0000002
+#define MBOX_CFGSTAT_STATE_ERROR_AUTH 0xf0000003
+#define MBOX_CFGSTAT_STATE_ERROR_CORE_IO 0xf0000004
+#define MBOX_CFGSTAT_STATE_ERROR_HARDWARE 0xf0000005
+#define MBOX_CFGSTAT_STATE_ERROR_FAKE 0xf0000006
+#define MBOX_CFGSTAT_STATE_ERROR_BOOT_INFO 0xf0000007
+#define MBOX_CFGSTAT_STATE_ERROR_QSPI_ERROR 0xf0000008
+
+#define RCF_SOFTFUNC_STATUS_CONF_DONE BIT(0)
+#define RCF_SOFTFUNC_STATUS_INIT_DONE BIT(1)
+#define RCF_SOFTFUNC_STATUS_SEU_ERROR BIT(3)
+#define RCF_PIN_STATUS_NSTATUS BIT(31)
+
+int mbox_send_cmd(u8 id, u32 cmd, u8 is_indirect, u32 len, u32 *arg, u8 urgent,
+ u32 *resp_buf_len, u32 *resp_buf);
+int mbox_send_cmd_psci(u8 id, u32 cmd, u8 is_indirect, u32 len, u32 *arg,
+ u8 urgent, u32 *resp_buf_len, u32 *resp_buf);
+int mbox_send_cmd_only(u8 id, u32 cmd, u8 is_indirect, u32 len, u32 *arg);
+int mbox_send_cmd_only_psci(u8 id, u32 cmd, u8 is_indirect, u32 len, u32 *arg);
+int mbox_rcv_resp(u32 *resp_buf, u32 resp_buf_max_len);
+int mbox_rcv_resp_psci(u32 *resp_buf, u32 resp_buf_max_len);
+int mbox_init(void);
+
+#ifdef CONFIG_CADENCE_QSPI
+int mbox_qspi_close(void);
+int mbox_qspi_open(void);
+#endif
+
+int mbox_reset_cold(void);
+
+#endif /* _MAILBOX_S10_H_ */
diff --git a/arch/arm/mach-socfpga/include/mach/misc.h b/arch/arm/mach-socfpga/include/mach/misc.h
index 197f09a..7fe77ac 100644
--- a/arch/arm/mach-socfpga/include/mach/misc.h
+++ b/arch/arm/mach-socfpga/include/mach/misc.h
@@ -27,4 +27,6 @@
unsigned int uart_com_port(const void *blob);
#endif
+void do_bridge_reset(int enable);
+
#endif /* _MISC_H_ */
diff --git a/arch/arm/mach-socfpga/include/mach/sdram_s10.h b/arch/arm/mach-socfpga/include/mach/sdram_s10.h
new file mode 100644
index 0000000..91bfc0e
--- /dev/null
+++ b/arch/arm/mach-socfpga/include/mach/sdram_s10.h
@@ -0,0 +1,183 @@
+/* SPDX-License-Identifier: GPL-2.0
+ *
+ * Copyright (C) 2017-2018 Intel Corporation <www.intel.com>
+ *
+ */
+
+#ifndef _SDRAM_S10_H_
+#define _SDRAM_S10_H_
+
+unsigned long sdram_calculate_size(void);
+int sdram_mmr_init_full(unsigned int sdr_phy_reg);
+int sdram_calibration_full(void);
+
+#define DDR_TWR 15
+#define DDR_READ_LATENCY_DELAY 40
+#define DDR_ACTIVATE_FAWBANK 0x1
+
+/* ECC HMC registers */
+#define DDRIOCTRL 0x8
+#define DDRCALSTAT 0xc
+#define DRAMADDRWIDTH 0xe0
+#define ECCCTRL1 0x100
+#define ECCCTRL2 0x104
+#define ERRINTEN 0x110
+#define INTMODE 0x11c
+#define INTSTAT 0x120
+#define AUTOWB_CORRADDR 0x138
+#define ECC_REG2WRECCDATABUS 0x144
+#define ECC_DIAGON 0x150
+#define ECC_DECSTAT 0x154
+#define HPSINTFCSEL 0x210
+#define RSTHANDSHAKECTRL 0x214
+#define RSTHANDSHAKESTAT 0x218
+
+#define DDR_HMC_DDRIOCTRL_IOSIZE_MSK 0x00000003
+#define DDR_HMC_DDRCALSTAT_CAL_MSK BIT(0)
+#define DDR_HMC_ECCCTL_AWB_CNT_RST_SET_MSK BIT(16)
+#define DDR_HMC_ECCCTL_CNT_RST_SET_MSK BIT(8)
+#define DDR_HMC_ECCCTL_ECC_EN_SET_MSK BIT(0)
+#define DDR_HMC_ECCCTL2_RMW_EN_SET_MSK BIT(8)
+#define DDR_HMC_ECCCTL2_AWB_EN_SET_MSK BIT(0)
+#define DDR_HMC_ECC_DIAGON_ECCDIAGON_EN_SET_MSK BIT(16)
+#define DDR_HMC_ECC_DIAGON_WRDIAGON_EN_SET_MSK BIT(0)
+#define DDR_HMC_ERRINTEN_SERRINTEN_EN_SET_MSK BIT(0)
+#define DDR_HMC_ERRINTEN_DERRINTEN_EN_SET_MSK BIT(1)
+#define DDR_HMC_INTSTAT_SERRPENA_SET_MSK BIT(0)
+#define DDR_HMC_INTSTAT_DERRPENA_SET_MSK BIT(1)
+#define DDR_HMC_INTSTAT_ADDRMTCFLG_SET_MSK BIT(16)
+#define DDR_HMC_INTMODE_INTMODE_SET_MSK BIT(0)
+#define DDR_HMC_RSTHANDSHAKE_MASK 0x000000ff
+#define DDR_HMC_CORE2SEQ_INT_REQ 0xF
+#define DDR_HMC_SEQ2CORE_INT_RESP_MASK BIT(3)
+#define DDR_HMC_HPSINTFCSEL_ENABLE_MASK 0x001f1f1f
+
+/* NOC DDR scheduler */
+#define DDR_SCH_ID_COREID 0
+#define DDR_SCH_ID_REVID 0x4
+#define DDR_SCH_DDRCONF 0x8
+#define DDR_SCH_DDRTIMING 0xc
+#define DDR_SCH_DDRMODE 0x10
+#define DDR_SCH_READ_LATENCY 0x14
+#define DDR_SCH_ACTIVATE 0x38
+#define DDR_SCH_DEVTODEV 0x3c
+#define DDR_SCH_DDR4TIMING 0x40
+
+#define DDR_SCH_DDRTIMING_ACTTOACT_OFF 0
+#define DDR_SCH_DDRTIMING_RDTOMISS_OFF 6
+#define DDR_SCH_DDRTIMING_WRTOMISS_OFF 12
+#define DDR_SCH_DDRTIMING_BURSTLEN_OFF 18
+#define DDR_SCH_DDRTIMING_RDTOWR_OFF 21
+#define DDR_SCH_DDRTIMING_WRTORD_OFF 26
+#define DDR_SCH_DDRTIMING_BWRATIO_OFF 31
+#define DDR_SCH_DDRMOD_BWRATIOEXTENDED_OFF 1
+#define DDR_SCH_ACTIVATE_RRD_OFF 0
+#define DDR_SCH_ACTIVATE_FAW_OFF 4
+#define DDR_SCH_ACTIVATE_FAWBANK_OFF 10
+#define DDR_SCH_DEVTODEV_BUSRDTORD_OFF 0
+#define DDR_SCH_DEVTODEV_BUSRDTOWR_OFF 2
+#define DDR_SCH_DEVTODEV_BUSWRTORD_OFF 4
+
+/* HMC MMR IO48 registers */
+#define CTRLCFG0 0x28
+#define CTRLCFG1 0x2c
+#define DRAMTIMING0 0x50
+#define CALTIMING0 0x7c
+#define CALTIMING1 0x80
+#define CALTIMING2 0x84
+#define CALTIMING3 0x88
+#define CALTIMING4 0x8c
+#define CALTIMING9 0xa0
+#define DRAMADDRW 0xa8
+#define DRAMSTS 0xec
+#define NIOSRESERVED0 0x110
+#define NIOSRESERVED1 0x114
+#define NIOSRESERVED2 0x118
+
+#define DRAMADDRW_CFG_COL_ADDR_WIDTH(x) \
+ (((x) >> 0) & 0x1F)
+#define DRAMADDRW_CFG_ROW_ADDR_WIDTH(x) \
+ (((x) >> 5) & 0x1F)
+#define DRAMADDRW_CFG_BANK_ADDR_WIDTH(x) \
+ (((x) >> 10) & 0xF)
+#define DRAMADDRW_CFG_BANK_GRP_ADDR_WIDTH(x) \
+ (((x) >> 14) & 0x3)
+#define DRAMADDRW_CFG_CS_ADDR_WIDTH(x) \
+ (((x) >> 16) & 0x7)
+
+#define CTRLCFG0_CFG_MEMTYPE(x) \
+ (((x) >> 0) & 0xF)
+#define CTRLCFG0_CFG_DIMM_TYPE(x) \
+ (((x) >> 4) & 0x7)
+#define CTRLCFG0_CFG_AC_POS(x) \
+ (((x) >> 7) & 0x3)
+#define CTRLCFG0_CFG_CTRL_BURST_LEN(x) \
+ (((x) >> 9) & 0x1F)
+
+#define CTRLCFG1_CFG_DBC3_BURST_LEN(x) \
+ (((x) >> 0) & 0x1F)
+#define CTRLCFG1_CFG_ADDR_ORDER(x) \
+ (((x) >> 5) & 0x3)
+#define CTRLCFG1_CFG_CTRL_EN_ECC(x) \
+ (((x) >> 7) & 0x1)
+
+#define DRAMTIMING0_CFG_TCL(x) \
+ (((x) >> 0) & 0x7F)
+
+#define CALTIMING0_CFG_ACT_TO_RDWR(x) \
+ (((x) >> 0) & 0x3F)
+#define CALTIMING0_CFG_ACT_TO_PCH(x) \
+ (((x) >> 6) & 0x3F)
+#define CALTIMING0_CFG_ACT_TO_ACT(x) \
+ (((x) >> 12) & 0x3F)
+#define CALTIMING0_CFG_ACT_TO_ACT_DB(x) \
+ (((x) >> 18) & 0x3F)
+
+#define CALTIMING1_CFG_RD_TO_RD(x) \
+ (((x) >> 0) & 0x3F)
+#define CALTIMING1_CFG_RD_TO_RD_DC(x) \
+ (((x) >> 6) & 0x3F)
+#define CALTIMING1_CFG_RD_TO_RD_DB(x) \
+ (((x) >> 12) & 0x3F)
+#define CALTIMING1_CFG_RD_TO_WR(x) \
+ (((x) >> 18) & 0x3F)
+#define CALTIMING1_CFG_RD_TO_WR_DC(x) \
+ (((x) >> 24) & 0x3F)
+
+#define CALTIMING2_CFG_RD_TO_WR_DB(x) \
+ (((x) >> 0) & 0x3F)
+#define CALTIMING2_CFG_RD_TO_WR_PCH(x) \
+ (((x) >> 6) & 0x3F)
+#define CALTIMING2_CFG_RD_AP_TO_VALID(x) \
+ (((x) >> 12) & 0x3F)
+#define CALTIMING2_CFG_WR_TO_WR(x) \
+ (((x) >> 18) & 0x3F)
+#define CALTIMING2_CFG_WR_TO_WR_DC(x) \
+ (((x) >> 24) & 0x3F)
+
+#define CALTIMING3_CFG_WR_TO_WR_DB(x) \
+ (((x) >> 0) & 0x3F)
+#define CALTIMING3_CFG_WR_TO_RD(x) \
+ (((x) >> 6) & 0x3F)
+#define CALTIMING3_CFG_WR_TO_RD_DC(x) \
+ (((x) >> 12) & 0x3F)
+#define CALTIMING3_CFG_WR_TO_RD_DB(x) \
+ (((x) >> 18) & 0x3F)
+#define CALTIMING3_CFG_WR_TO_PCH(x) \
+ (((x) >> 24) & 0x3F)
+
+#define CALTIMING4_CFG_WR_AP_TO_VALID(x) \
+ (((x) >> 0) & 0x3F)
+#define CALTIMING4_CFG_PCH_TO_VALID(x) \
+ (((x) >> 6) & 0x3F)
+#define CALTIMING4_CFG_PCH_ALL_TO_VALID(x) \
+ (((x) >> 12) & 0x3F)
+#define CALTIMING4_CFG_ARF_TO_VALID(x) \
+ (((x) >> 18) & 0xFF)
+#define CALTIMING4_CFG_PDN_TO_VALID(x) \
+ (((x) >> 26) & 0x3F)
+
+#define CALTIMING9_CFG_4_ACT_TO_ACT(x) \
+ (((x) >> 0) & 0xFF)
+
+#endif /* _SDRAM_S10_H_ */
diff --git a/arch/arm/mach-socfpga/mailbox_s10.c b/arch/arm/mach-socfpga/mailbox_s10.c
new file mode 100644
index 0000000..cccd1a4
--- /dev/null
+++ b/arch/arm/mach-socfpga/mailbox_s10.c
@@ -0,0 +1,380 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017-2018 Intel Corporation <www.intel.com>
+ *
+ */
+
+#include <common.h>
+#include <wait_bit.h>
+#include <asm/io.h>
+#include <asm/arch/mailbox_s10.h>
+#include <asm/arch/system_manager.h>
+#include <asm/secure.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define MBOX_READL(reg) \
+ readl(SOCFPGA_MAILBOX_ADDRESS + (reg))
+
+#define MBOX_WRITEL(data, reg) \
+ writel(data, SOCFPGA_MAILBOX_ADDRESS + (reg))
+
+#define MBOX_READ_RESP_BUF(rout) \
+ MBOX_READL(MBOX_RESP_BUF + ((rout) * sizeof(u32)))
+
+#define MBOX_WRITE_CMD_BUF(data, cin) \
+ MBOX_WRITEL(data, MBOX_CMD_BUF + ((cin) * sizeof(u32)))
+
+static __always_inline int mbox_polling_resp(u32 rout)
+{
+ u32 rin;
+ unsigned long i = ~0;
+
+ while (i) {
+ rin = MBOX_READL(MBOX_RIN);
+ if (rout != rin)
+ return 0;
+
+ i--;
+ }
+
+ return -ETIMEDOUT;
+}
+
+/* Check for available slot and write to circular buffer.
+ * It also update command valid offset (cin) register.
+ */
+static __always_inline int mbox_fill_cmd_circular_buff(u32 header, u32 len,
+ u32 *arg)
+{
+ u32 cin;
+ u32 cout;
+ u32 i;
+
+ cin = MBOX_READL(MBOX_CIN) % MBOX_CMD_BUFFER_SIZE;
+ cout = MBOX_READL(MBOX_COUT) % MBOX_CMD_BUFFER_SIZE;
+
+ /* if command buffer is full or not enough free space
+ * to fit the data
+ */
+ if (((cin + 1) % MBOX_CMD_BUFFER_SIZE) == cout ||
+ ((MBOX_CMD_BUFFER_SIZE - cin + cout - 1) %
+ MBOX_CMD_BUFFER_SIZE) < len)
+ return -ENOMEM;
+
+ /* write header to circular buffer */
+ MBOX_WRITE_CMD_BUF(header, cin++);
+ /* wrapping around when it reach the buffer size */
+ cin %= MBOX_CMD_BUFFER_SIZE;
+
+ /* write arguments */
+ for (i = 0; i < len; i++) {
+ MBOX_WRITE_CMD_BUF(arg[i], cin++);
+ /* wrapping around when it reach the buffer size */
+ cin %= MBOX_CMD_BUFFER_SIZE;
+ }
+
+ /* write command valid offset */
+ MBOX_WRITEL(cin, MBOX_CIN);
+
+ return 0;
+}
+
+/* Check the command and fill it into circular buffer */
+static __always_inline int mbox_prepare_cmd_only(u8 id, u32 cmd,
+ u8 is_indirect, u32 len,
+ u32 *arg)
+{
+ u32 header;
+ int ret;
+
+ /* Total length is command + argument length */
+ if ((len + 1) > MBOX_CMD_BUFFER_SIZE)
+ return -EINVAL;
+
+ if (cmd > MBOX_MAX_CMD_INDEX)
+ return -EINVAL;
+
+ header = MBOX_CMD_HEADER(MBOX_CLIENT_ID_UBOOT, id, len,
+ (is_indirect) ? 1 : 0, cmd);
+
+ ret = mbox_fill_cmd_circular_buff(header, len, arg);
+
+ return ret;
+}
+
+/* Send command only without waiting for responses from SDM */
+static __always_inline int mbox_send_cmd_only_common(u8 id, u32 cmd,
+ u8 is_indirect, u32 len,
+ u32 *arg)
+{
+ int ret = mbox_prepare_cmd_only(id, cmd, is_indirect, len, arg);
+ /* write doorbell */
+ MBOX_WRITEL(1, MBOX_DOORBELL_TO_SDM);
+
+ return ret;
+}
+
+/* Return number of responses received in buffer */
+static __always_inline int __mbox_rcv_resp(u32 *resp_buf, u32 resp_buf_max_len)
+{
+ u32 rin;
+ u32 rout;
+ u32 resp_len = 0;
+
+ /* clear doorbell from SDM if it was SET */
+ if (MBOX_READL(MBOX_DOORBELL_FROM_SDM) & 1)
+ MBOX_WRITEL(0, MBOX_DOORBELL_FROM_SDM);
+
+ /* read current response offset */
+ rout = MBOX_READL(MBOX_ROUT);
+ /* read response valid offset */
+ rin = MBOX_READL(MBOX_RIN);
+
+ while (rin != rout && (resp_len < resp_buf_max_len)) {
+ /* Response received */
+ if (resp_buf)
+ resp_buf[resp_len++] = MBOX_READ_RESP_BUF(rout);
+
+ rout++;
+ /* wrapping around when it reach the buffer size */
+ rout %= MBOX_RESP_BUFFER_SIZE;
+ /* update next ROUT */
+ MBOX_WRITEL(rout, MBOX_ROUT);
+ }
+
+ return resp_len;
+}
+
+/* Support one command and up to 31 words argument length only */
+static __always_inline int mbox_send_cmd_common(u8 id, u32 cmd, u8 is_indirect,
+ u32 len, u32 *arg, u8 urgent,
+ u32 *resp_buf_len,
+ u32 *resp_buf)
+{
+ u32 rin;
+ u32 resp;
+ u32 rout;
+ u32 status;
+ u32 resp_len;
+ u32 buf_len;
+ int ret;
+
+ ret = mbox_prepare_cmd_only(id, cmd, is_indirect, len, arg);
+ if (ret)
+ return ret;
+
+ if (urgent) {
+ /* Read status because it is toggled */
+ status = MBOX_READL(MBOX_STATUS) & MBOX_STATUS_UA_MSK;
+ /* Send command as urgent command */
+ MBOX_WRITEL(1, MBOX_URG);
+ }
+
+ /* write doorbell */
+ MBOX_WRITEL(1, MBOX_DOORBELL_TO_SDM);
+
+ while (1) {
+ ret = ~0;
+
+ /* Wait for doorbell from SDM */
+ while (!MBOX_READL(MBOX_DOORBELL_FROM_SDM) && ret--)
+ ;
+ if (!ret)
+ return -ETIMEDOUT;
+
+ /* clear interrupt */
+ MBOX_WRITEL(0, MBOX_DOORBELL_FROM_SDM);
+
+ if (urgent) {
+ u32 new_status = MBOX_READL(MBOX_STATUS);
+ /* urgent command doesn't have response */
+ MBOX_WRITEL(0, MBOX_URG);
+ /* Urgent ACK is toggled */
+ if ((new_status & MBOX_STATUS_UA_MSK) ^ status)
+ return 0;
+
+ return -ECOMM;
+ }
+
+ /* read current response offset */
+ rout = MBOX_READL(MBOX_ROUT);
+
+ /* read response valid offset */
+ rin = MBOX_READL(MBOX_RIN);
+
+ if (rout != rin) {
+ /* Response received */
+ resp = MBOX_READ_RESP_BUF(rout);
+ rout++;
+ /* wrapping around when it reach the buffer size */
+ rout %= MBOX_RESP_BUFFER_SIZE;
+ /* update next ROUT */
+ MBOX_WRITEL(rout, MBOX_ROUT);
+
+ /* check client ID and ID */
+ if ((MBOX_RESP_CLIENT_GET(resp) ==
+ MBOX_CLIENT_ID_UBOOT) &&
+ (MBOX_RESP_ID_GET(resp) == id)) {
+ ret = MBOX_RESP_ERR_GET(resp);
+ if (ret)
+ return ret;
+
+ if (resp_buf_len) {
+ buf_len = *resp_buf_len;
+ *resp_buf_len = 0;
+ } else {
+ buf_len = 0;
+ }
+
+ resp_len = MBOX_RESP_LEN_GET(resp);
+ while (resp_len) {
+ ret = mbox_polling_resp(rout);
+ if (ret)
+ return ret;
+ /* we need to process response buffer
+ * even caller doesn't need it
+ */
+ resp = MBOX_READ_RESP_BUF(rout);
+ rout++;
+ resp_len--;
+ rout %= MBOX_RESP_BUFFER_SIZE;
+ MBOX_WRITEL(rout, MBOX_ROUT);
+ if (buf_len) {
+ /* copy response to buffer */
+ resp_buf[*resp_buf_len] = resp;
+ (*resp_buf_len)++;
+ buf_len--;
+ }
+ }
+ return ret;
+ }
+ }
+ };
+
+ return -EIO;
+}
+
+int mbox_init(void)
+{
+ int ret;
+
+ /* enable mailbox interrupts */
+ MBOX_WRITEL(MBOX_ALL_INTRS, MBOX_FLAGS);
+
+ /* Ensure urgent request is cleared */
+ MBOX_WRITEL(0, MBOX_URG);
+
+ /* Ensure the Doorbell Interrupt is cleared */
+ MBOX_WRITEL(0, MBOX_DOORBELL_FROM_SDM);
+
+ ret = mbox_send_cmd(MBOX_ID_UBOOT, MBOX_RESTART, MBOX_CMD_DIRECT, 0,
+ NULL, 1, 0, NULL);
+ if (ret)
+ return ret;
+
+ /* Renable mailbox interrupts after MBOX_RESTART */
+ MBOX_WRITEL(MBOX_ALL_INTRS, MBOX_FLAGS);
+
+ return 0;
+}
+
+#ifdef CONFIG_CADENCE_QSPI
+int mbox_qspi_close(void)
+{
+ return mbox_send_cmd(MBOX_ID_UBOOT, MBOX_QSPI_CLOSE, MBOX_CMD_DIRECT,
+ 0, NULL, 0, 0, NULL);
+}
+
+int mbox_qspi_open(void)
+{
+ static const struct socfpga_system_manager *sysmgr_regs =
+ (struct socfpga_system_manager *)SOCFPGA_SYSMGR_ADDRESS;
+
+ int ret;
+ u32 resp_buf[1];
+ u32 resp_buf_len;
+
+ ret = mbox_send_cmd(MBOX_ID_UBOOT, MBOX_QSPI_OPEN, MBOX_CMD_DIRECT,
+ 0, NULL, 0, 0, NULL);
+ if (ret) {
+ /* retry again by closing and reopen the QSPI again */
+ ret = mbox_qspi_close();
+ if (ret)
+ return ret;
+
+ ret = mbox_send_cmd(MBOX_ID_UBOOT, MBOX_QSPI_OPEN,
+ MBOX_CMD_DIRECT, 0, NULL, 0, 0, NULL);
+ if (ret)
+ return ret;
+ }
+
+ /* HPS will directly control the QSPI controller, no longer mailbox */
+ resp_buf_len = 1;
+ ret = mbox_send_cmd(MBOX_ID_UBOOT, MBOX_QSPI_DIRECT, MBOX_CMD_DIRECT,
+ 0, NULL, 0, (u32 *)&resp_buf_len,
+ (u32 *)&resp_buf);
+ if (ret)
+ goto error;
+
+ /* We are getting QSPI ref clock and set into sysmgr boot register */
+ printf("QSPI: Reference clock at %d Hz\n", resp_buf[0]);
+ writel(resp_buf[0], &sysmgr_regs->boot_scratch_cold0);
+
+ return 0;
+
+error:
+ mbox_qspi_close();
+
+ return ret;
+}
+#endif /* CONFIG_CADENCE_QSPI */
+
+int mbox_reset_cold(void)
+{
+ int ret;
+
+ ret = mbox_send_cmd(MBOX_ID_UBOOT, MBOX_REBOOT_HPS, MBOX_CMD_DIRECT,
+ 0, NULL, 0, 0, NULL);
+ if (ret) {
+ /* mailbox sent failure, wait for watchdog to kick in */
+ hang();
+ }
+ return 0;
+}
+
+int mbox_send_cmd(u8 id, u32 cmd, u8 is_indirect, u32 len, u32 *arg,
+ u8 urgent, u32 *resp_buf_len, u32 *resp_buf)
+{
+ return mbox_send_cmd_common(id, cmd, is_indirect, len, arg, urgent,
+ resp_buf_len, resp_buf);
+}
+
+int __secure mbox_send_cmd_psci(u8 id, u32 cmd, u8 is_indirect, u32 len,
+ u32 *arg, u8 urgent, u32 *resp_buf_len,
+ u32 *resp_buf)
+{
+ return mbox_send_cmd_common(id, cmd, is_indirect, len, arg, urgent,
+ resp_buf_len, resp_buf);
+}
+
+int mbox_send_cmd_only(u8 id, u32 cmd, u8 is_indirect, u32 len, u32 *arg)
+{
+ return mbox_send_cmd_only_common(id, cmd, is_indirect, len, arg);
+}
+
+int __secure mbox_send_cmd_only_psci(u8 id, u32 cmd, u8 is_indirect, u32 len,
+ u32 *arg)
+{
+ return mbox_send_cmd_only_common(id, cmd, is_indirect, len, arg);
+}
+
+int mbox_rcv_resp(u32 *resp_buf, u32 resp_buf_max_len)
+{
+ return __mbox_rcv_resp(resp_buf, resp_buf_max_len);
+}
+
+int __secure mbox_rcv_resp_psci(u32 *resp_buf, u32 resp_buf_max_len)
+{
+ return __mbox_rcv_resp(resp_buf, resp_buf_max_len);
+}
diff --git a/arch/arm/mach-socfpga/misc.c b/arch/arm/mach-socfpga/misc.c
index fca8650..77628e1 100644
--- a/arch/arm/mach-socfpga/misc.c
+++ b/arch/arm/mach-socfpga/misc.c
@@ -40,7 +40,9 @@
int dram_init(void)
{
- gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE);
+ if (fdtdec_setup_memory_size() != 0)
+ return -EINVAL;
+
return 0;
}
@@ -204,3 +206,34 @@
return 0;
}
#endif
+
+#ifndef CONFIG_SPL_BUILD
+static int do_bridge(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ if (argc != 2)
+ return CMD_RET_USAGE;
+
+ argv++;
+
+ switch (*argv[0]) {
+ case 'e': /* Enable */
+ do_bridge_reset(1);
+ break;
+ case 'd': /* Disable */
+ do_bridge_reset(0);
+ break;
+ default:
+ return CMD_RET_USAGE;
+ }
+
+ return 0;
+}
+
+U_BOOT_CMD(bridge, 2, 1, do_bridge,
+ "SoCFPGA HPS FPGA bridge control",
+ "enable - Enable HPS-to-FPGA, FPGA-to-HPS, LWHPS-to-FPGA bridges\n"
+ "bridge disable - Enable HPS-to-FPGA, FPGA-to-HPS, LWHPS-to-FPGA bridges\n"
+ ""
+);
+
+#endif
diff --git a/arch/arm/mach-socfpga/misc_arria10.c b/arch/arm/mach-socfpga/misc_arria10.c
index 47a9d50..a75cbc4 100644
--- a/arch/arm/mach-socfpga/misc_arria10.c
+++ b/arch/arm/mach-socfpga/misc_arria10.c
@@ -14,6 +14,7 @@
#include <asm/arch/misc.h>
#include <asm/arch/pinmux.h>
#include <asm/arch/reset_manager.h>
+#include <asm/arch/reset_manager_arria10.h>
#include <asm/arch/sdram_arria10.h>
#include <asm/arch/system_manager.h>
#include <asm/arch/nic301.h>
@@ -262,3 +263,11 @@
return socfpga_eth_reset();
}
#endif
+
+void do_bridge_reset(int enable)
+{
+ if (enable)
+ socfpga_reset_deassert_bridges_handoff();
+ else
+ socfpga_bridges_reset();
+}
diff --git a/arch/arm/mach-socfpga/misc_gen5.c b/arch/arm/mach-socfpga/misc_gen5.c
index 4343734..848551c 100644
--- a/arch/arm/mach-socfpga/misc_gen5.c
+++ b/arch/arm/mach-socfpga/misc_gen5.c
@@ -259,40 +259,20 @@
: : "r"(val), "r"(&sdr_ctrl->static_cfg) : "memory", "cc");
}
-static int do_bridge(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+void do_bridge_reset(int enable)
{
- if (argc != 2)
- return CMD_RET_USAGE;
-
- argv++;
-
- switch (*argv[0]) {
- case 'e': /* Enable */
+ if (enable) {
writel(iswgrp_handoff[2], &sysmgr_regs->fpgaintfgrp_module);
socfpga_sdram_apply_static_cfg();
writel(iswgrp_handoff[3], &sdr_ctrl->fpgaport_rst);
writel(iswgrp_handoff[0], &reset_manager_base->brg_mod_reset);
writel(iswgrp_handoff[1], &nic301_regs->remap);
- break;
- case 'd': /* Disable */
+ } else {
writel(0, &sysmgr_regs->fpgaintfgrp_module);
writel(0, &sdr_ctrl->fpgaport_rst);
socfpga_sdram_apply_static_cfg();
writel(0, &reset_manager_base->brg_mod_reset);
writel(1, &nic301_regs->remap);
- break;
- default:
- return CMD_RET_USAGE;
}
-
- return 0;
}
-
-U_BOOT_CMD(
- bridge, 2, 1, do_bridge,
- "SoCFPGA HPS FPGA bridge control",
- "enable - Enable HPS-to-FPGA, FPGA-to-HPS, LWHPS-to-FPGA bridges\n"
- "bridge disable - Enable HPS-to-FPGA, FPGA-to-HPS, LWHPS-to-FPGA bridges\n"
- ""
-);
#endif
diff --git a/arch/arm/mach-socfpga/misc_s10.c b/arch/arm/mach-socfpga/misc_s10.c
new file mode 100644
index 0000000..918baac
--- /dev/null
+++ b/arch/arm/mach-socfpga/misc_s10.c
@@ -0,0 +1,133 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2016-2018 Intel Corporation <www.intel.com>
+ *
+ */
+
+#include <altera.h>
+#include <common.h>
+#include <errno.h>
+#include <fdtdec.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/arch/reset_manager.h>
+#include <asm/arch/system_manager.h>
+#include <asm/arch/misc.h>
+#include <asm/pl310.h>
+#include <linux/libfdt.h>
+
+#include <dt-bindings/reset/altr,rst-mgr-s10.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static struct socfpga_system_manager *sysmgr_regs =
+ (struct socfpga_system_manager *)SOCFPGA_SYSMGR_ADDRESS;
+
+/*
+ * DesignWare Ethernet initialization
+ */
+#ifdef CONFIG_ETH_DESIGNWARE
+
+static u32 socfpga_phymode_setup(u32 gmac_index, const char *phymode)
+{
+ u32 modereg;
+
+ if (!phymode)
+ return -EINVAL;
+
+ if (!strcmp(phymode, "mii") || !strcmp(phymode, "gmii"))
+ modereg = SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_GMII_MII;
+ else if (!strcmp(phymode, "rgmii"))
+ modereg = SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_RGMII;
+ else if (!strcmp(phymode, "rmii"))
+ modereg = SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_RMII;
+ else
+ return -EINVAL;
+
+ clrsetbits_le32(&sysmgr_regs->emac0 + gmac_index,
+ SYSMGR_EMACGRP_CTRL_PHYSEL_MASK,
+ modereg);
+
+ return 0;
+}
+
+static int socfpga_set_phymode(void)
+{
+ const void *fdt = gd->fdt_blob;
+ struct fdtdec_phandle_args args;
+ const char *phy_mode;
+ u32 gmac_index;
+ int nodes[2]; /* Max. 3 GMACs */
+ int ret, count;
+ int i, node;
+
+ count = fdtdec_find_aliases_for_id(fdt, "ethernet",
+ COMPAT_ALTERA_SOCFPGA_DWMAC,
+ nodes, ARRAY_SIZE(nodes));
+ for (i = 0; i < count; i++) {
+ node = nodes[i];
+ if (node <= 0)
+ continue;
+
+ ret = fdtdec_parse_phandle_with_args(fdt, node, "resets",
+ "#reset-cells", 1, 0,
+ &args);
+ if (ret || args.args_count != 1) {
+ debug("GMAC%i: Failed to parse DT 'resets'!\n", i);
+ continue;
+ }
+
+ gmac_index = args.args[0] - EMAC0_RESET;
+
+ phy_mode = fdt_getprop(fdt, node, "phy-mode", NULL);
+ ret = socfpga_phymode_setup(gmac_index, phy_mode);
+ if (ret) {
+ debug("GMAC%i: Failed to parse DT 'phy-mode'!\n", i);
+ continue;
+ }
+ }
+
+ return 0;
+}
+#else
+static int socfpga_set_phymode(void)
+{
+ return 0;
+};
+#endif
+
+/*
+ * Print CPU information
+ */
+#if defined(CONFIG_DISPLAY_CPUINFO)
+int print_cpuinfo(void)
+{
+ puts("CPU: Intel FPGA SoCFPGA Platform (ARMv8 64bit Cortex-A53)\n");
+
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_ARCH_MISC_INIT
+int arch_misc_init(void)
+{
+ char qspi_string[13];
+
+ sprintf(qspi_string, "<0x%08x>", cm_get_qspi_controller_clk_hz());
+ env_set("qspi_clock", qspi_string);
+
+ socfpga_set_phymode();
+ return 0;
+}
+#endif
+
+int arch_early_init_r(void)
+{
+ return 0;
+}
+
+void do_bridge_reset(int enable)
+{
+ socfpga_bridges_reset(enable);
+}
diff --git a/arch/arm/mach-socfpga/mmu-arm64_s10.c b/arch/arm/mach-socfpga/mmu-arm64_s10.c
new file mode 100644
index 0000000..670ceb9
--- /dev/null
+++ b/arch/arm/mach-socfpga/mmu-arm64_s10.c
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2016-2018 Intel Corporation <www.intel.com>
+ *
+ */
+
+#include <common.h>
+#include <asm/armv8/mmu.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static struct mm_region socfpga_stratix10_mem_map[] = {
+ {
+ /* MEM 2GB*/
+ .virt = 0x0UL,
+ .phys = 0x0UL,
+ .size = 0x80000000UL,
+ .attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) |
+ PTE_BLOCK_INNER_SHARE,
+ }, {
+ /* FPGA 1.5GB */
+ .virt = 0x80000000UL,
+ .phys = 0x80000000UL,
+ .size = 0x60000000UL,
+ .attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
+ PTE_BLOCK_NON_SHARE |
+ PTE_BLOCK_PXN | PTE_BLOCK_UXN,
+ }, {
+ /* DEVICE 142MB */
+ .virt = 0xF7000000UL,
+ .phys = 0xF7000000UL,
+ .size = 0x08E00000UL,
+ .attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
+ PTE_BLOCK_NON_SHARE |
+ PTE_BLOCK_PXN | PTE_BLOCK_UXN,
+ }, {
+ /* OCRAM 1MB but available 256KB */
+ .virt = 0xFFE00000UL,
+ .phys = 0xFFE00000UL,
+ .size = 0x00100000UL,
+ .attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) |
+ PTE_BLOCK_INNER_SHARE,
+ }, {
+ /* DEVICE 32KB */
+ .virt = 0xFFFC0000UL,
+ .phys = 0xFFFC0000UL,
+ .size = 0x00008000UL,
+ .attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
+ PTE_BLOCK_NON_SHARE |
+ PTE_BLOCK_PXN | PTE_BLOCK_UXN,
+ }, {
+ /* MEM 124GB */
+ .virt = 0x0100000000UL,
+ .phys = 0x0100000000UL,
+ .size = 0x1F00000000UL,
+ .attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) |
+ PTE_BLOCK_INNER_SHARE,
+ }, {
+ /* DEVICE 4GB */
+ .virt = 0x2000000000UL,
+ .phys = 0x2000000000UL,
+ .size = 0x0100000000UL,
+ .attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
+ PTE_BLOCK_NON_SHARE |
+ PTE_BLOCK_PXN | PTE_BLOCK_UXN,
+ }, {
+ /* List terminator */
+ },
+};
+
+struct mm_region *mem_map = socfpga_stratix10_mem_map;
diff --git a/arch/arm/mach-socfpga/spl_a10.c b/arch/arm/mach-socfpga/spl_a10.c
new file mode 100644
index 0000000..fe4782c
--- /dev/null
+++ b/arch/arm/mach-socfpga/spl_a10.c
@@ -0,0 +1,104 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2012 Altera Corporation <www.altera.com>
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/pl310.h>
+#include <asm/u-boot.h>
+#include <asm/utils.h>
+#include <image.h>
+#include <asm/arch/reset_manager.h>
+#include <spl.h>
+#include <asm/arch/system_manager.h>
+#include <asm/arch/freeze_controller.h>
+#include <asm/arch/clock_manager.h>
+#include <asm/arch/scan_manager.h>
+#include <asm/arch/sdram.h>
+#include <asm/arch/scu.h>
+#include <asm/arch/nic301.h>
+#include <asm/sections.h>
+#include <fdtdec.h>
+#include <watchdog.h>
+#include <asm/arch/pinmux.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static const struct socfpga_system_manager *sysmgr_regs =
+ (struct socfpga_system_manager *)SOCFPGA_SYSMGR_ADDRESS;
+
+u32 spl_boot_device(void)
+{
+ const u32 bsel = readl(&sysmgr_regs->bootinfo);
+
+ switch (SYSMGR_GET_BOOTINFO_BSEL(bsel)) {
+ case 0x1: /* FPGA (HPS2FPGA Bridge) */
+ return BOOT_DEVICE_RAM;
+ case 0x2: /* NAND Flash (1.8V) */
+ case 0x3: /* NAND Flash (3.0V) */
+ socfpga_per_reset(SOCFPGA_RESET(NAND), 0);
+ return BOOT_DEVICE_NAND;
+ case 0x4: /* SD/MMC External Transceiver (1.8V) */
+ case 0x5: /* SD/MMC Internal Transceiver (3.0V) */
+ socfpga_per_reset(SOCFPGA_RESET(SDMMC), 0);
+ socfpga_per_reset(SOCFPGA_RESET(DMA), 0);
+ return BOOT_DEVICE_MMC1;
+ case 0x6: /* QSPI Flash (1.8V) */
+ case 0x7: /* QSPI Flash (3.0V) */
+ socfpga_per_reset(SOCFPGA_RESET(QSPI), 0);
+ return BOOT_DEVICE_SPI;
+ default:
+ printf("Invalid boot device (bsel=%08x)!\n", bsel);
+ hang();
+ }
+}
+
+#ifdef CONFIG_SPL_MMC_SUPPORT
+u32 spl_boot_mode(const u32 boot_device)
+{
+#if defined(CONFIG_SPL_FAT_SUPPORT) || defined(CONFIG_SPL_EXT_SUPPORT)
+ return MMCSD_MODE_FS;
+#else
+ return MMCSD_MODE_RAW;
+#endif
+}
+#endif
+
+void spl_board_init(void)
+{
+ /* configuring the clock based on handoff */
+ cm_basic_init(gd->fdt_blob);
+ WATCHDOG_RESET();
+
+ config_dedicated_pins(gd->fdt_blob);
+ WATCHDOG_RESET();
+
+ /* Release UART from reset */
+ socfpga_reset_uart(0);
+
+ /* enable console uart printing */
+ preloader_console_init();
+}
+
+void board_init_f(ulong dummy)
+{
+ /*
+ * Configure Clock Manager to use intosc clock instead external osc to
+ * ensure success watchdog operation. We do it as early as possible.
+ */
+ cm_use_intosc();
+
+ socfpga_watchdog_disable();
+
+ arch_early_init_r();
+
+#ifdef CONFIG_HW_WATCHDOG
+ /* release osc1 watchdog timer 0 from reset */
+ socfpga_reset_deassert_osc1wd0();
+
+ /* reconfigure and enable the watchdog */
+ hw_watchdog_init();
+ WATCHDOG_RESET();
+#endif /* CONFIG_HW_WATCHDOG */
+}
diff --git a/arch/arm/mach-socfpga/spl.c b/arch/arm/mach-socfpga/spl_gen5.c
similarity index 81%
rename from arch/arm/mach-socfpga/spl.c
rename to arch/arm/mach-socfpga/spl_gen5.c
index 0c9d738..d6fe7d3 100644
--- a/arch/arm/mach-socfpga/spl.c
+++ b/arch/arm/mach-socfpga/spl_gen5.c
@@ -22,21 +22,15 @@
#include <asm/sections.h>
#include <fdtdec.h>
#include <watchdog.h>
-#if defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
-#include <asm/arch/pinmux.h>
-#endif
DECLARE_GLOBAL_DATA_PTR;
-#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
static struct pl310_regs *const pl310 =
(struct pl310_regs *)CONFIG_SYS_PL310_BASE;
static struct scu_registers *scu_regs =
(struct scu_registers *)SOCFPGA_MPUSCU_ADDRESS;
static struct nic301_registers *nic301_regs =
(struct nic301_registers *)SOCFPGA_L3REGS_ADDRESS;
-#endif
-
static const struct socfpga_system_manager *sysmgr_regs =
(struct socfpga_system_manager *)SOCFPGA_SYSMGR_ADDRESS;
@@ -65,8 +59,18 @@
hang();
}
}
+
+#ifdef CONFIG_SPL_MMC_SUPPORT
+u32 spl_boot_mode(const u32 boot_device)
+{
+#if defined(CONFIG_SPL_FAT_SUPPORT) || defined(CONFIG_SPL_EXT_SUPPORT)
+ return MMCSD_MODE_FS;
+#else
+ return MMCSD_MODE_RAW;
+#endif
+}
+#endif
-#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
static void socfpga_nic301_slave_ns(void)
{
writel(0x1, &nic301_regs->lwhps2fpgaregs);
@@ -177,47 +181,3 @@
/* Configure simple malloc base pointer into RAM. */
gd->malloc_base = CONFIG_SYS_TEXT_BASE + (1024 * 1024);
}
-#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
-void spl_board_init(void)
-{
- /* configuring the clock based on handoff */
- cm_basic_init(gd->fdt_blob);
- WATCHDOG_RESET();
-
- config_dedicated_pins(gd->fdt_blob);
- WATCHDOG_RESET();
-
- /* Release UART from reset */
- socfpga_reset_uart(0);
-
- /* enable console uart printing */
- preloader_console_init();
-
- WATCHDOG_RESET();
-
- /* Add device descriptor to FPGA device table */
- socfpga_fpga_add();
-}
-
-void board_init_f(ulong dummy)
-{
- /*
- * Configure Clock Manager to use intosc clock instead external osc to
- * ensure success watchdog operation. We do it as early as possible.
- */
- cm_use_intosc();
-
- socfpga_watchdog_disable();
-
- arch_early_init_r();
-
-#ifdef CONFIG_HW_WATCHDOG
- /* release osc1 watchdog timer 0 from reset */
- socfpga_reset_deassert_osc1wd0();
-
- /* reconfigure and enable the watchdog */
- hw_watchdog_init();
- WATCHDOG_RESET();
-#endif /* CONFIG_HW_WATCHDOG */
-}
-#endif
diff --git a/arch/arm/mach-socfpga/spl_s10.c b/arch/arm/mach-socfpga/spl_s10.c
new file mode 100644
index 0000000..69d6e91
--- /dev/null
+++ b/arch/arm/mach-socfpga/spl_s10.c
@@ -0,0 +1,200 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2016-2018 Intel Corporation <www.intel.com>
+ *
+ */
+
+#include <asm/io.h>
+#include <asm/u-boot.h>
+#include <asm/utils.h>
+#include <common.h>
+#include <debug_uart.h>
+#include <image.h>
+#include <spl.h>
+#include <asm/arch/clock_manager.h>
+#include <asm/arch/firewall_s10.h>
+#include <asm/arch/mailbox_s10.h>
+#include <asm/arch/reset_manager.h>
+#include <asm/arch/sdram_s10.h>
+#include <asm/arch/system_manager.h>
+#include <watchdog.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static struct socfpga_system_manager *sysmgr_regs =
+ (struct socfpga_system_manager *)SOCFPGA_SYSMGR_ADDRESS;
+
+u32 spl_boot_device(void)
+{
+ /* TODO: Get from SDM or handoff */
+ return BOOT_DEVICE_MMC1;
+}
+
+#ifdef CONFIG_SPL_MMC_SUPPORT
+u32 spl_boot_mode(const u32 boot_device)
+{
+#if defined(CONFIG_SPL_FAT_SUPPORT) || defined(CONFIG_SPL_EXT_SUPPORT)
+ return MMCSD_MODE_FS;
+#else
+ return MMCSD_MODE_RAW;
+#endif
+}
+#endif
+
+void spl_disable_firewall_l4_per(void)
+{
+ const struct socfpga_firwall_l4_per *firwall_l4_per_base =
+ (struct socfpga_firwall_l4_per *)SOCFPGA_FIREWALL_L4_PER;
+ u32 i;
+ const u32 *addr[] = {
+ &firwall_l4_per_base->nand,
+ &firwall_l4_per_base->nand_data,
+ &firwall_l4_per_base->usb0,
+ &firwall_l4_per_base->usb1,
+ &firwall_l4_per_base->spim0,
+ &firwall_l4_per_base->spim1,
+ &firwall_l4_per_base->emac0,
+ &firwall_l4_per_base->emac1,
+ &firwall_l4_per_base->emac2,
+ &firwall_l4_per_base->sdmmc,
+ &firwall_l4_per_base->gpio0,
+ &firwall_l4_per_base->gpio1,
+ &firwall_l4_per_base->i2c0,
+ &firwall_l4_per_base->i2c1,
+ &firwall_l4_per_base->i2c2,
+ &firwall_l4_per_base->i2c3,
+ &firwall_l4_per_base->i2c4,
+ &firwall_l4_per_base->timer0,
+ &firwall_l4_per_base->timer1,
+ &firwall_l4_per_base->uart0,
+ &firwall_l4_per_base->uart1
+ };
+
+ /*
+ * The following lines of code will enable non-secure access
+ * to nand, usb, spi, emac, sdmmc, gpio, i2c, timers and uart. This
+ * is needed as most OS run in non-secure mode. Thus we need to
+ * enable non-secure access to these peripherals in order for the
+ * OS to use these peripherals.
+ */
+ for (i = 0; i < ARRAY_SIZE(addr); i++)
+ writel(FIREWALL_L4_DISABLE_ALL, addr[i]);
+}
+
+void spl_disable_firewall_l4_sys(void)
+{
+ const struct socfpga_firwall_l4_sys *firwall_l4_sys_base =
+ (struct socfpga_firwall_l4_sys *)SOCFPGA_FIREWALL_L4_SYS;
+ u32 i;
+ const u32 *addr[] = {
+ &firwall_l4_sys_base->dma_ecc,
+ &firwall_l4_sys_base->emac0rx_ecc,
+ &firwall_l4_sys_base->emac0tx_ecc,
+ &firwall_l4_sys_base->emac1rx_ecc,
+ &firwall_l4_sys_base->emac1tx_ecc,
+ &firwall_l4_sys_base->emac2rx_ecc,
+ &firwall_l4_sys_base->emac2tx_ecc,
+ &firwall_l4_sys_base->nand_ecc,
+ &firwall_l4_sys_base->nand_read_ecc,
+ &firwall_l4_sys_base->nand_write_ecc,
+ &firwall_l4_sys_base->ocram_ecc,
+ &firwall_l4_sys_base->sdmmc_ecc,
+ &firwall_l4_sys_base->usb0_ecc,
+ &firwall_l4_sys_base->usb1_ecc,
+ &firwall_l4_sys_base->clock_manager,
+ &firwall_l4_sys_base->io_manager,
+ &firwall_l4_sys_base->reset_manager,
+ &firwall_l4_sys_base->system_manager,
+ &firwall_l4_sys_base->watchdog0,
+ &firwall_l4_sys_base->watchdog1,
+ &firwall_l4_sys_base->watchdog2,
+ &firwall_l4_sys_base->watchdog3
+ };
+
+ for (i = 0; i < ARRAY_SIZE(addr); i++)
+ writel(FIREWALL_L4_DISABLE_ALL, addr[i]);
+}
+
+void board_init_f(ulong dummy)
+{
+ const struct cm_config *cm_default_cfg = cm_get_default_config();
+ int ret;
+
+#ifdef CONFIG_HW_WATCHDOG
+ /* Ensure watchdog is paused when debugging is happening */
+ writel(SYSMGR_WDDBG_PAUSE_ALL_CPU, &sysmgr_regs->wddbg);
+
+ /* Enable watchdog before initializing the HW */
+ socfpga_per_reset(SOCFPGA_RESET(L4WD0), 1);
+ socfpga_per_reset(SOCFPGA_RESET(L4WD0), 0);
+ hw_watchdog_init();
+#endif
+
+ /* ensure all processors are not released prior Linux boot */
+ writeq(0, CPU_RELEASE_ADDR);
+
+ socfpga_per_reset(SOCFPGA_RESET(OSC1TIMER0), 0);
+ timer_init();
+
+ populate_sysmgr_pinmux();
+
+ /* configuring the HPS clocks */
+ cm_basic_init(cm_default_cfg);
+
+#ifdef CONFIG_DEBUG_UART
+ socfpga_per_reset(SOCFPGA_RESET(UART0), 0);
+ debug_uart_init();
+#endif
+ ret = spl_early_init();
+ if (ret) {
+ debug("spl_early_init() failed: %d\n", ret);
+ hang();
+ }
+
+ preloader_console_init();
+ cm_print_clock_quick_summary();
+
+ /* enable non-secure interface to DMA330 DMA and peripherals */
+ writel(SYSMGR_DMA_IRQ_NS | SYSMGR_DMA_MGR_NS, &sysmgr_regs->dma);
+ writel(SYSMGR_DMAPERIPH_ALL_NS, &sysmgr_regs->dma_periph);
+
+ spl_disable_firewall_l4_per();
+
+ spl_disable_firewall_l4_sys();
+
+ /* disable lwsocf2fpga and soc2fpga bridge security */
+ writel(FIREWALL_BRIDGE_DISABLE_ALL, SOCFPGA_FIREWALL_SOC2FPGA);
+ writel(FIREWALL_BRIDGE_DISABLE_ALL, SOCFPGA_FIREWALL_LWSOC2FPGA);
+
+ /* disable SMMU security */
+ writel(FIREWALL_L4_DISABLE_ALL, SOCFPGA_FIREWALL_TCU);
+
+ /* disable ocram security at CCU for non secure access */
+ clrbits_le32(CCU_REG_ADDR(CCU_CPU0_MPRT_ADMASK_MEM_RAM0),
+ CCU_ADMASK_P_MASK | CCU_ADMASK_NS_MASK);
+ clrbits_le32(CCU_REG_ADDR(CCU_IOM_MPRT_ADMASK_MEM_RAM0),
+ CCU_ADMASK_P_MASK | CCU_ADMASK_NS_MASK);
+
+ debug("DDR: Initializing Hard Memory Controller\n");
+ if (sdram_mmr_init_full(0)) {
+ puts("DDR: Initialization failed.\n");
+ hang();
+ }
+
+ gd->ram_size = sdram_calculate_size();
+ printf("DDR: %d MiB\n", (int)(gd->ram_size >> 20));
+
+ /* Sanity check ensure correct SDRAM size specified */
+ debug("DDR: Running SDRAM size sanity check\n");
+ if (get_ram_size(0, gd->ram_size) != gd->ram_size) {
+ puts("DDR: SDRAM size check failed!\n");
+ hang();
+ }
+ debug("DDR: SDRAM size check passed!\n");
+
+ mbox_init();
+
+#ifdef CONFIG_CADENCE_QSPI
+ mbox_qspi_open();
+#endif
+}
diff --git a/arch/arm/mach-socfpga/timer_s10.c b/arch/arm/mach-socfpga/timer_s10.c
new file mode 100644
index 0000000..5723789
--- /dev/null
+++ b/arch/arm/mach-socfpga/timer_s10.c
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017-2018 Intel Corporation <www.intel.com>
+ *
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/timer.h>
+
+/*
+ * Timer initialization
+ */
+int timer_init(void)
+{
+ int enable = 0x3; /* timer enable + output signal masked */
+ int loadval = ~0;
+
+ /* enable system counter */
+ writel(enable, SOCFPGA_GTIMER_SEC_ADDRESS);
+ /* enable processor pysical counter */
+ asm volatile("msr cntp_ctl_el0, %0" : : "r" (enable));
+ asm volatile("msr cntp_tval_el0, %0" : : "r" (loadval));
+
+ return 0;
+}