/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * (C) Copyright 2011
 * egnite GmbH <info@egnite.de>
 *
 * Configuation settings for Ethernut 5 with AT91SAM9XE.
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#include <asm/hardware.h>

/* The first stage boot loader expects u-boot running at this address. */

/* The first stage boot loader takes care of low level initialization. */

/* CPU information */

/* ARM asynchronous clock */
#define CFG_SYS_AT91_SLOW_CLOCK	32768	/* slow clock xtal */
#define CFG_SYS_AT91_MAIN_CLOCK	18432000 /* 18.432 MHz crystal */

/* 32kB internal SRAM */
#define CFG_SYS_INIT_RAM_ADDR	0x00300000 /*AT91SAM9XE_SRAM_BASE */
#define CFG_SYS_INIT_RAM_SIZE	(32 << 10)

/* 128MB SDRAM in 1 bank */
#define CFG_SYS_SDRAM_BASE		0x20000000
#define CFG_SYS_SDRAM_SIZE		(128 << 20)

/* 512kB on-chip NOR flash */
# define CFG_SYS_FLASH_BASE		0x00200000 /* AT91SAM9XE_FLASH_BASE */

/* bootstrap + u-boot + env + linux in dataflash on CS0 */

/* NAND flash */
#ifdef CONFIG_CMD_NAND
#define CFG_SYS_NAND_BASE		0x40000000
/* our ALE is AD21 */
#define CFG_SYS_NAND_MASK_ALE	(1 << 21)
/* our CLE is AD22 */
#define CFG_SYS_NAND_MASK_CLE	(1 << 22)
#define CFG_SYS_NAND_ENABLE_PIN	GPIO_PIN_PC(14)
#endif

/* JFFS2 */

/* Ethernet */
#define CFG_PHY_ID			0

/* MMC */
#ifdef CONFIG_CMD_MMC
#define CFG_SYS_MMC_CD_PIN		AT91_PIO_PORTC, 8
#endif

/* RTC */
#if defined(CONFIG_CMD_DATE) || defined(CONFIG_CMD_SNTP)
#define CFG_SYS_I2C_RTC_ADDR		0x51
#endif

#define I2C_SOFT_DECLARATIONS

#define GPIO_I2C_SCL		AT91_PIO_PORTA, 24
#define GPIO_I2C_SDA		AT91_PIO_PORTA, 23

#define I2C_INIT { \
	at91_set_pio_periph(AT91_PIO_PORTA, 23, 0); \
	at91_set_pio_multi_drive(AT91_PIO_PORTA, 23, 1); \
	at91_set_pio_periph(AT91_PIO_PORTA, 24, 0); \
	at91_set_pio_output(AT91_PIO_PORTA, 24, 0); \
	at91_set_pio_multi_drive(AT91_PIO_PORTA, 24, 1); \
}

#define I2C_ACTIVE	at91_set_pio_output(AT91_PIO_PORTA, 23, 0)
#define I2C_TRISTATE	at91_set_pio_input(AT91_PIO_PORTA, 23, 0)
#define I2C_SCL(bit)	at91_set_pio_value(AT91_PIO_PORTA, 24, bit)
#define I2C_SDA(bit)	at91_set_pio_value(AT91_PIO_PORTA, 23, bit)
#define I2C_DELAY	udelay(100)
#define I2C_READ	at91_get_pio_value(AT91_PIO_PORTA, 23)

/* File systems */

/* Boot command */

/* Misc. u-boot settings */

#endif